Winegard Power Supply Rv 0751 Users Manual 2451487

RV-0751 to the manual 16befd92-9ef8-4ac9-b0c8-a56c3b244154

: Winegard Winegard-Power-Supply-Rv-0751-Users-Manual-479774 winegard-power-supply-rv-0751-users-manual-479774 winegard pdf

Open the PDF directly: View PDF .
Page Count: 2

This unit is equipped with a polyswitch,

(current limiting device), which will shut down

+12VDC if there is a direct short between

antenna and power supply. Green indicator

light will not light. Once short is eliminated,

device will reset itself in approximately 2 minutes.

DESCRIPTION

Wall plate/power supply to operate Winegard

RV antenna with outdoor receptacle for TV set

and cable or satellite input. Wall plate/power

supply provides +12 VDC to antenna as well as

antenna signals to two TV sets. Cable input

from outdoor receptacle connects to wall plate

and may be switched so either antenna or cable

signals may be watched. See applications.

There is also an auxiliary jack for a third

signal.

NOTE: THIS UNIT IS NOT AN AMPLIFIER. USE ONLY

WITH A WINEGARD AMPLIFIED RV ANTENNA.

INSTRUCTIONS

WINEGARD COMPANY

3000 KIRKWOOD ST., BURLINGTON, IA 52601-2000

Printed in U.S.A. 2451487 REV2 1/10

STEP 4. Install connectors on downlead and

set 2 cable as shown in Figure 5. Attach

downlead cable to jack on wall plate/power

supply marked antenna as shown in Figure 4.

Attach cable going to set 2 outlet to jack on

power supply marked SET 2. Attach cable

coming from cable input to jack on power

supply marked CABLE.

OPERATION: To receive cable signals from

outdoor receptacle: Press switch to (OFF)

position. Light on wallplate will go (OFF)

showing that power is no longer connected to

the antenna and the TV sets are receiving

signals from outdoor receptacle. To receive

signals from antenna: Press switch to (ON)

position. Light on wall plate will come (ON)

showing that power is connected to the antenna

and theTV sets are receiving signals from the

antenna. NOTE: Make sure TV antenna is in

the (UP) position and pointed at the station

RV WALL PLATE/

POWER SUPPLY

MODEL RV-0751 (almond bulk)

MODEL RV-0752 (white bulk)

MODEL RV-7542 (white single)

Made in U.S.A.

INSTALLING FC-5910

CONNECTORS ON COAX CABLE

1/2" *

¼" *

Center Conductor

Inner Insulation

Outer Cover

Crimp Here

1.

2.

3.

STEP 1: Strip outer cover back 1/2"* from end of cable. Fray braid

back as far as outer cover will allow.

STEP 2: Trim braid close to outer cover and remove 1/4"* of inner

insulation being careful not to nick center conductor. Make

sure no foil or braid can touch center conductor.

STEP 3: Slide connector tip between braid and inner insulation

(braid and foil, on foil shield cable) and push connector on cable as

far as it will go. Crimp built-in ferrule with proper crimping tool. Hex

connector requires hex crimping tool. Do Not crush cable out-

of-round.

* If installing in very hot weather, increase dimensions 1/8".

STEP 5. Mount power supply in wall with

screws provided and attach TV set cable to jack

on front. Connect band separator to VHF and

UHF antenna terminals of TV set, if required.

Press switch on front of outlet and check that

light is on.

Figure 4

Figure 5

desired. To receive satellite signal, attach

coax from receiver/antenna to Auxiliary jack

on wall plate.

Antenna Cable

Auxiliary

(Satellite Receiver)

Set 2

WINEGARD MOBILE PRODUCTS LIMITED WARRANTY

(2 YEARS PARTS; 1 YEAR LABOR)

Winegard Company warrants this product against defects in

materials or workmanship for a period of two (2) years from the date

of original purchase. During year one (1) of such warranty, Winegard

Company will also pay authorized labor costs to an authorized

Winegard dealer to repair or replace defective products. No warranty

claim will be honored unless at the time the claim is made, Customer

presents proof of purchase to an authorized Winegard dealer (to

locate the nearest authorized Winegard dealer, contact Winegard

Company, 3000 Kirkwood Street, Burlington, Iowa 52601,

Telephone 800-288-8094 or visit www.winegard.com). Customer

must provide proof of purchase with a dated sales receipt for the

Winegard product to verify the product is under warranty. If the date

of purchase cannot be verified, the warranty period shall be

considered to begin thirty (30) days after the date of manufacture.

If a defect in material or workmanship is discovered, Customer

may take the product to an authorized Winegard dealer for service.

Customer must provide proof of purchase to verify the product is

under warranty. If the product is brought to an authorized Winegard

dealer for service prior to expiration of year one (1) of the warranty

period and a defect in material or workmanship is verified by

Winegard Technical Services, Winegard Company will cover the

Winegard dealer’s labor charges for warranty service. The Winegard

dealer must contact Winegard Technical Services in advance for

pre-approval of the service. Approval of the service is at the sole

discretion of Winegard Company.

Alternatively, Customer may ship the product prepaid to Winegard

Technical Services (located at 3111 Kirkwood Street, Burlington,

Iowa 52601, Telephone 800-788-4417). Customer must return the

product along with a brief description of the problem and provide

Winegard Technical Services with Customer’s name, address,

and phone number. Customer must also provide proof of purchase

to verify the product is under warranty. If the product is returned

before the expiration of the warranty period, Winegard Company

will (at its option) either repair or replace the product.

This Limited Warranty does not apply if the product has been

damaged, deteriorates, malfunctions or fails from: improper

installation, misuse, abuse, neglect, accident, tampering,

modification of the product as originally manufactured by Winegard

in any manner whatsoever, removing or defacing any serial number,

usage not in accordance with product instructions or acts of nature

such as damage caused by wind, lightning, ice or corrosive

environments such as salt spray and acid rain. This Limited Warranty

also does not apply if the product becomes unable to perform its’

intended function in any way as a result of the television signal

provider making any changes in technology or service.

RETURN AUTHORIZATION POLICY

A Return Material Authorization (RMA) is required prior to returning

any product to Winegard Company or Winegard Warranty Services

under this warranty policy. Please call our Technical Services

Department at 800-788-4417 or send an e-mail to

warranty@winegard.com to obtain the RMA number. Please furnish

the date of purchase when requesting an RMA number. Enclose

the product in a prepaid package and write the RMA number in

large, clear letters on the outside of the package. To avoid confusion

or misunderstanding, a shipment(s) without an RMA number(s) or

an unauthorized return(s) will be refused and returned to Customer

freight collect.

WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES

FOR ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, MADE

BY ANY OTHER PERSON.

ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED

OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR

A PARTICULAR PURPOSE AND MERCHANTABILITY ARE

LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY.

In states that do not allow limitations on implied warranties, or

the exclusion of limitation of incidental or consequential damages,

the above limitations or exclusions do not apply.

Some states do not allow limitations on how long an implied

warranty lasts, or the exclusion of limitation of incidental or

consequential damages, so the above limitations or exclusions

may not apply to you.

This warranty gives Customer specific legal rights. Customer

may also have other rights that may vary from state to state.

SATELLITE RECEIVER WARRANTY:

See manufacturer’s limited warranty policy.

WS-MOBWARREV2 Rev. 1/10

Example 3

WARNING: Use of this on/off

power switch with any product

other than Winegard amplified

RV antenna, could result in fire

or other damage.

INSTRUCTIONS

APPLICATIONS AND

ALTERNATE CONNECTIONS

STEP 1. Select location for wall plate and

patio receptacle if required. Run coax cables

between locations and install connectors on

each end. Mark cables so they may be

identified. Antenna downlead and +12 VDC

will also be needed at inside wall plate/power

supply location.

STEP 2. The wall plate assembly may be

flush mounted in most standard electrical boxes.

To flush mount, cut a hole in wall to fit the box.

Route all cables to the wall plate and other

outlets required at this time. The Auxiliary

jack is designed for the use of satellite

receivers, etc. requiring direct line input.

WHEN CONNECTING CABLE OR WIRES

BE SURE SWITCH IS IN OFF POSITION.

STEP 3. Make +12 VDC connection by

running two #12 wires between the wall plate

and +12 VDC source. Install terminals on wires

from +12 VDC source as shown in Figure 1.

Crimp terminals with Craftsman type 4 crimping

tool or equivalent. Push wires onto tabs on

terminal board as shown in Figure 2. If in doubt

as to the polarity of the wires, connect them

temporarily to tabs on circuit board and press

switch on front of outlet. If light comes on,

polarity is correct. See Figure 3.

Figure 2

Figure 3

Auxilliary

Antenna Outdoor Receptacle

WA-1010

TV

Outlet

Antenna

Input

Cable Input

Cable Input

Set 1

Example 1

Antenna Outdoor Receptacle

WA-1010

TV

Outlet

Antenna

Input

TG-7221

Cable

Input

Set 2

Set 1

SP-1002

Splitter

Example 2

Antenna

Antenna

Input

TG-7221

Cable

Input

Set 2

Set 1

ON/OFF

Switch

ON/OFF

Switch

ON/OFF

Switch

Outdoor Receptacle

WA-1010

Figure 1

Connector

Insulation

Remove 1/4" of

insulation from

#12 wire.

#12 Wire

1/4"

Connector

Ferrule

Crimp Here

+12 VDC

Ground

Set 1

Set 2