Delta Networks HB97 802.11 bgn RF Module User Manual
Delta Networks, Inc. 802.11 bgn RF Module
User Manual
HB97
Product Specification
802.11n/g 2.4GHz (2x2) WLAN PCI Express MiniCard Adapter
Note: This document contains proprietary technical information in which is the property of the Delta Networks
Inc. and shall not be disclosed to others in whole or in part, reproduced, copied, or used as the basis for
design, manufacturing, or sale of apparatus without written permission of Delta Networks Inc.
Delta Networks Inc. ii
Table Of Contents
1. REVISION HISTORY...................................................................................................................................................... 1
1.1. DOCUMENT REVISION HISTORY................................................................................................................................... 1
2. GENERAL DESCRIPTION ............................................................................................................................................ 2
2.1. FEATURES .................................................................................................................................................................... 2
2.2. MECHANICAL DESIGN.................................................................................................................................................. 3
2.3. IC SOLUTION ............................................................................................................................................................... 4
2.4. VID, DID, SVID AND SPID ASSIGNMENT................................................................................................................... 5
3. TECHNICAL SPECIFICATIONS.................................................................................................................................. 6
Delta Networks Inc. 1
1. Revision History
Revision Date Remark
1.00 2011/1/4 Product proposal
1.1. Document Revision History
Revision Date Remark
1.00 2011/1/4 Preliminary product proposal
1.01 2011/9/27 Change Tx measured output power in peak value
Delta Networks Inc. 2
2. General Description
HB97 is compliant with miniPCI Express v1.1 standard Adapter. The Atheros 802.11g/n technique delivers up to
54Mbps (802.11g) and IEEE802.11n data rate support the channel bandwidth support 20MHz for 150Mbps and
40MHz channel bandwidth for 300Mbps ( 2Tx2R) and support legacy WLAN standard IEEE802.11b, IEEE802.11g
data rate, it use 2 sets of 2.4Ghz Tx / Rx antenna’s combinations and applied Transmit Beamforming and Receive
combining to focus energy and CDD, MRC to improve 802.11n performance. The IEEE802.11g is OFDM
modulation and CCK modulation compliant with IEEE802.11b standard. It supports the Quality of Service for
802.11e. (WMM) and also 802.11e burst mode feature to enable robust wireless streaming of audio and video
content while remaining compatible with any 802.11b/g device and with high throughput link
2.1. Features
Form Factor – a compatible with PCI Express v1.1 MiniCard Adapter
Support for IEEE 802.11g standard, IEEE802.11b and IEEE802.11n compliant
Support 802.11e (WMM), 802.11h, 802.11j and
Security support for WEP, TKIP and AES and IEEE802.11i
Data rate 802.11b/g: 1,2,5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54-Mbps
802.11n rate at 300Mbps for 40MHz and 150Mbps for 20MHz
Drivers - Microsoft®Windows® XP, Vista and Win7
Delta Networks Inc. 3
2.2. Mechanical Design
The Dimension : L x W (mm): 30mm x27mm
Delta Networks Inc. 4
2.3. IC Solution
The IC solution for HB97:
P/N Functionality Description
AR9287 A powerful IEEE11g/n
MAC/BBP for PCI-e card
interface
AR9287 is single chip solution for 2.4GHz 802.11n-ready ; it
integrates a multiple protocol MAC, Baseband Processor and
ADC/DAC converters with 2x2 MIMO radio transceiver including
LNA, PA, and RF Switch and PCIe v1.1 interface; AR9287
imlements half duplex OFDM, CCK and DSSS baseband
processing supporting up to 130Mbps for 20MHz and 300Mbps
for 40MHz channel operations respectively and IEEE802.11b/g
data rates.it also provide QoS and CDD, MRC coexistence with
Bluetooth. The package is LPCC (76-pin 9x9 mm)
Delta Networks Inc. 5
2.4. VID, DID, SVID and SPID assignment
The SVID and SPID may provide from customer.
1. Vendor ID (VID): use Chip’s vendor ID = 0x168C
2. Device ID (DID): use Chip’s device ID = 0x4013
3. Sub-Vendor ID (SVID): use manufacture’s ID = 0x??
4. Sub-Product ID (SPID): use manufacture’s product ID = 0x??
Delta Networks Inc. 6
3. Technical Specifications
HB97 Specification
Specification Wireless LAN PC Card
WLAN Standard IEEE802.11b, IEEE 802.11g; IEEE802.11e, IEEE802.11h; IEEE802.11i;
IEEE802.11n standard
Data Rate IEEE802.11b/g: 1/2/5.5/6/9/11/12/18/24/36/48 and 54Mbps
And 802.11n data rate up to 300Mbps ( 40MHz); 130Mbps ( 20MHz)
Wireless Medium Complementary code keying (CCK) and Orthogonal Frequency Division
Multiplexing (OFDM); MIMO-OFDM
Frequency Band 2.4GHzband:ISM band 2.412 –2.472, 2.484GHz
Modulation Technique OFDM: BPSK@6/9 Mbps, QPSK@12/18Mbps, 16-QAM@24Mbps
64-QAM@48/54Mbps
DSSS: DBPSK @1Mbps, DQPSK@2Mbps, and CCK@5.5/11Mbps
MIMO-OFDM: BPSK, QPSK, 16QAM and 64QAM
Wired Equivalent Privacy 64-bit, 128-bit data encryption
Number of
non-overlapping
Channels
802.11g: US and EU and Japan 3 channels
802.11b: US and EU and Japan 3 channels
802.11n at 40MHz for 2.4GHz are 2422MHz, 2452MHz channels
Antenna 2X Tx and 2X Rx
Delta Networks Inc. 7
HB97 specification (continued)
Specification Wireless LAN PC Card
Receive Sensitivity 11b@CH6 -86dBm@11Mbps
11g@CH6: -74dBm@54Mbps; CH13: -74dBm@54Mbps
11n-20MHz BW: 2437MHz for MCS7: -70dBm
2437MHz for MCS15: -68dBm
11n-40MHz BW: 2422MHz for MCS7: -68dBm
2422MHz for MCS15: -65dBm
Max output power 11b 19.9dBm@1Mbps
11g 24dBm@6Mbps
11n-20MHz BW : MCS0: 23.8dBm
11n-40MHz BW : MCS0: 22.7dBm
Power consumption Measured for 2xTx / 2x Rx:
For TX: @ HT40: MCS0 1947mW@653mA
Drivers Windows 2000 and XP
Security AES
Certification Prescan the module for FCC Part 15 (North America) Compliant
Form Factor PCI Expressv1.1 Mini-card
Operating Environment Temperature: 0~40℃ (operating)
-20~70℃ (storage)
Humidity (non-condensing): 10~90% RH
Dimension (L x W) 30mm x 27 mm
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This device is intended only for OEM integrators under the following
conditions:
1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna,
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the
final product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a separate
FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may
be installed such that 20 cm may be maintained between the antenna and users. The
final end product must be labeled in a visible area with the following: “Contains FCC
ID: PD5‐HB97”.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as
show in this manual.
Industry Canada statement:
Industry Canada statement:Industry Canada statement:
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
IMPORTANT NOTE:
IMPORTANT NOTE:IMPORTANT NOTE:
IMPORTANT NOTE: (For mobile device use)
(For mobile device use) (For mobile device use)
(For mobile device use)
Radiation Exposure Statement:
Radiation Exposure Statement:Radiation Exposure Statement:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
This device is intended only for OEM integrators under the following conditions:This device is intended only for OEM integrators under the following conditions:
This device is intended only for OEM integrators under the following conditions: (For
(For (For
(For
module device use)
module device use)module device use)
module device use)
1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna,
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for
any additional compliance requirements required with this module installed.
IMPORTANT NOTE:
IMPORTANT NOTE:IMPORTANT NOTE:
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the Canada
authorization is no longer considered valid and the IC ID can not be used on
the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate Canada authorization.
End Product Labeling
End Product LabelingEnd Product Labeling
End Product Labeling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the following:
“Contains IC:
3970A
3970A3970A
3970A-
--
-HB97
HB97HB97
HB97”.
Manual Information To the End User
Manual Information To the End UserManual Information To the End User
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux
appareils radio exempts de licence. Son fonctionnement est sujet aux deux
conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un
brouillage susceptible de provoquer un fonctionnement indésirable.
NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles)
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec
un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions
suivantes: (Pour utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est
respectée entre l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou
antenne,
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour
certaines configurations d'ordinateur portable ou de certaines co-localisation
avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme
valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces
circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y
compris l'émetteur) et l'obtention d'une autorisation distincte au Canada.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un
dispositif où l'antenne peut être installée de telle sorte qu'une distance de 20cm
peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit être
étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC:
3970A
3970A3970A
3970A-
--
-HB97
HB97HB97
HB97 ".
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à
l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le
manuel de l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires
requises et avertissements comme indiqué dans ce manuel.