Exceed Technology EX4C01 Water leak detector User Manual
Shenzhen Exceed Technology Co.,Ltd. Water leak detector
User Manual
WiFi Ready – Plug & Go PN: 900117121 VitalWIFI (EX4C01) is designed to bundle with the X4M200, X4M300 sensors. VitalWiFi equips the XeThru sensor modules with standalone power supply and WIFI communication capabilities. The X4M200 and X4M300 can now stream outputs independently and directly to data servers and cloud applications. Features Plug and Go XeThru UWB radar sensor system No extra hardware needed Standalone power system Provides WIFI communication and control; Provides power to X4M200 and X4M300; Physical interface to mount and secure the sensor Compact size Multiple encapsulation options Compatible with XeThru X4M200 & X4M300 EX4C01 works with X4M200, X4M300 Applications WiFi ready Respiration Sensor o EX4C01 + X4M200 WiFi ready Presence Sensor o EX4C01 + X4M300 VitalWIFI bridges the X4M200/X4M300 modules to an existing WiFi network. user can easily manage and control the device networking requirement. With VitalWIFI, X4M200/X4M300 module When VitalWiFi is working as a TCP Client, it will initiate request for 2-way Exceed Technology Co. Limited www.exceed-tech.com E: ask@exceed-tech.com, Tel: + 852 9738 7071, Whatsapp: +85297387071 WiFi Ready – Plug & Go connections with a TCP Server device. Upon successful connection, transparent transmission between Server and Client is enabled. The server end could be a fixed IP from the Internet, or a device within the network with an intranet IP Plug and Ready to use No further hardware development required. Using the Vital-WIFI, the XeThru sensor modules can now be managed via WIFI. Users only need to focus on developing the backend software interfaces. Schematic diagram VitalWIF(EX4C01) is made up of DC-DC voltage converter, WIFI module,connectors and LED. DC-DC converter steps down the +5V DC input to +3.4V DC. Maximum current 1.5A. Connector provides power to X4M200/X4M300, and the UART communication link WIFI module is based on ESP8285, which can establish transmission to a cloud server. LED is used to indicate WIFI status. When there is no network connection, the LED flashes in constant interval. When a connection is established, the LED is stands On. During data transmission, LED flashes when receiving and transmitting. Compact and easy to use Board dimensions are 50mm x 67.6mm x 21mm, when assembled with the X4M200 or X4M300. Special design considerations must be given to ensure signal integrity, especially with several RF antennas on board. Exceed Technology offers the product in standard encapsulation, custom encapsulations and PCB assembly. Mechanical drawings can be made available to support encapsulation designs. Technical Specifications Compatible with X4M200, X4M300 Frequency range:2.4G~2.5G(2400~2483.5M) Transmitting power: 802.11b: +20dBm Exceed Technology Co. Limited www.exceed-tech.com E: ask@exceed-tech.com, Tel: + 852 9738 7071, Whatsapp: +85297387071 WiFi Ready – Plug & Go 802.11g: +17dBm 802.11n: +14dBm receiving sensitivity: 802.11b: -91dBm 802.11g: -75dBm 802.11n: -72dBm Supports 80211 b/g/n/e/I; Supports Station、SoftAP、SoftAP+STA mode; Supports WI-FI Direct(P2P); Supports WPA/PA2 PSK and WPS; Seamless Roaming; Built-in HTTP Web Server, Supporting web configuration parameter; Supporting TCP Server,TCP Client,UDP Server,UDP Client and UDP Broadcast; Support AP enable, customize SSID/password, customize IP and network segments; Automatically scan peripheral hotspots, support STA enabling, DHCP, customize IP and network segments; Support for using serial port at command to set and view WIFI status; Remote Server address support DNS Domain name Auto-resolution; Antenna:PCB embedded antenna; UART : Default 115200 baud rate,8 data bits,1 stop bit,no parity. Parameters can be changed as needed Dimensions:50mm X 67.6 mm; Working Temperature :-40° to 125° Other Specifications Power supply: 5V DC Power current: 200mA (including X4M200/X4M300) PCB size: 50 x 67.6 mm Assembly size: 50 x 67.6 x 21 mm Exceed Technology Co. Limited www.exceed-tech.com E: ask@exceed-tech.com, Tel: + 852 9738 7071, Whatsapp: +85297387071 WiFi Ready – Plug & Go Availability and options Available from January 2018 Standard encapsulation o Color : White, Black o Dimension: 80 * 80 * 26 mm, o Material: ABS Custom encapsulation o Customized designs PCB Assembly o Design and manufacture your own encapsulation Exceed Technology Co. Limited www.exceed-tech.com E: ask@exceed-tech.com, Tel: + 852 9738 7071, Whatsapp: +85297387071 WiFi Ready – Plug & Go AT Command Instruction Set: Data Direction Instruction(ASCII Character string) Meaning Query STA state MCU WIFI AT+STASTATUS Query STA schema status WIFI MCU STA:OK STA connected WIFI MCU STA:DOWN STA disconnected Get the IP and MAC of the STA mode MCU WIFI WIFI MCU AT+STAINFO Mac|IP Sample 5CCF7F116380|192.168.1.102 Get the MAC and IP of WIFI MAC address and IP address in STA Mode Query the connection state in the TCP Client mode MCUWIFI AT+TCPCLIENT Query join status in TCP Client mode, no sense in other modes WIFIMCU TCP:OK TCP Client connected WIFIMCU TCP:OFF TCP Client disconnected MCU WIFI AT+RST Reset WIFI WIFI MCU RST:OK Response Reset WIFI Restoration of factory setting MCU WIFI AT+RESTORE WIFI Restore and reboot WIFI MCU RESTORE:OK Response Exceed WIFI module access and set up. 1. Please connect DC5V to the board ->System power up -> Green LED on WiFI board + LED on Xethru module flashing. 2. The module starts searching for WIFI networks. If this is new WiFi network, then User set up is required. Please note both AP and STATION modes are provided by the WiFi module. 3. Using a PC or mobile phone, search for ( Exceed_Wifi_xxxxxx) and connect to it. 4. Enter 192.168.4.1 to access WiFi set up. Exceed Technology Co. Limited www.exceed-tech.com E: ask@exceed-tech.com, Tel: + 852 9738 7071, Whatsapp: +85297387071 WiFi Ready – Plug & Go 5. Once connected, select STATUS , check that WiFi Status is showing “connecting”. 6. Select Module -> Serial 7. Confirm “Baudrate” is 115200 8. Save 9. 10. 11. 12. 13. Select Module -> WiFi Station Settings -> Enabled Enter the SSID name you are connecting to or select from the drop down SSID list Enter Password accordingly Save Exceed Technology Co. Limited www.exceed-tech.com E: ask@exceed-tech.com, Tel: + 852 9738 7071, Whatsapp: +85297387071 WiFi Ready – Plug & Go 14. Select Module -> Network 15. Socket Type -> TCP Client (VitalWIFI supports TCP Server、TCP Client、UDP Server、 UDP Client andUDP BroadCast. Depending on the network requirement, user may select any of the supported Socket Type and respective settings.), The following example uses TCP Client,ie: Socket Type ->TCP Client) 16. 17. TCP Client -> set the respective IP address and local port of the server Save Exceed Technology Co. Limited www.exceed-tech.com E: ask@exceed-tech.com, Tel: + 852 9738 7071, Whatsapp: +85297387071 WiFi Ready – Plug & Go 18. 19. Select More -> Restart - this will start the module with the new settings. Check for Restart Successful Exceed Technology Co. Limited www.exceed-tech.com E: ask@exceed-tech.com, Tel: + 852 9738 7071, Whatsapp: +85297387071 WiFi Ready – Plug & Go 20. 21. Select STATUS , check that WiFi Status is showing “connected”. Set Up Completed 22. Activate TCPUDPbg ( testing program) , select Server Mode and CreateServer. Set the Local IP address and LocalPort. Please note the settings here must be identical to those settings in step 18. Create TCP server. 23. Click - StartServer,establish TCP connection. Exceed Technology Co. Limited www.exceed-tech.com E: ask@exceed-tech.com, Tel: + 852 9738 7071, Whatsapp: +85297387071 WiFi Ready – Plug & Go 24. Click on ShowHex, to display the data in hex format. The content in the receiving window is the data received directly from the UART of X4M200.X4M300. ie transparent data transmission from VitalSCAN (TCP client) to TCP Serder. Exceed Technology Co. Limited www.exceed-tech.com E: ask@exceed-tech.com, Tel: + 852 9738 7071, Whatsapp: +85297387071 WiFi Ready – Plug & Go ATTENTION This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, this equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. FCC ID:2APQO-EX4C01 Exceed Technology Co. Limited www.exceed-tech.com E: ask@exceed-tech.com, Tel: + 852 9738 7071, Whatsapp: +85297387071
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Author : ALS Comments : Company : Create Date : 2018:05:09 20:41:30+12:30 Modify Date : 2018:05:10 16:01:40+08:00 Source Modified : D:20180509204130+12'41' Subject : Trapped : false XMP Toolkit : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08 Format : application/pdf Creator : ALS Description : Title : Creator Tool : WPS Office Metadata Date : 2018:05:10 16:01:40+08:00 Keywords : Producer : Document ID : uuid:9526dbdc-365b-4379-8f5d-f9669fdb560c Instance ID : uuid:2383e0f4-5ea7-40d8-b2dc-e54ee5a9e8e6 Page Count : 11EXIF Metadata provided by EXIF.tools