Huizhou Desay Auto Electronics RA11A0D08 Car Radio Receiver User Manual

Huizhou Desay Auto. Electronics Co.,LTD. Car Radio Receiver Users Manual

Users Manual

PLEASE READ THIS MANUAL BEFORE USING THE EQUIPMENT.
INSTRUCTION MANUAL
MP3/WMA/USB PLAYER WITH FM/AM RECEIVER
RA11A0
MIC
USB
3 RDM 4 5 +
1 2
AUX
IN
BAND
AF
MENU
SRC
Use only in a 12-volt DC negative-ground electric-
al system.
Be sure to connect the colour coded leads according
to the diagram.
Incorrect connections may cause the unit to mal-
function or damage the vehicles, electrical system.
Be sure to connect the speaker (-) leads to the
speaker (-) terminal.
Never connect the left and right channel speaker
cables each other or to the vehicle body.
Make sure all the connections are completely
correct before turning on your unit.
Using a fuse with a higher amperage rating may
cause serious damage to the unit.
DO NOT attempt to disassemble the unit.
Laser beams from the optical pick up are dangerous
to the eyes.
Do NOT block vents or radiator panels. Doing so
many cause heat to build up inside and may result
in fire.
Make sure those pins or other foreign objects do
not get inside the unit; they may cause malfunctions,
or create safety hazards such as electrical shock
or laser beam exposure.
Keep the volume at a level at which you can hear
outside warning sounds (horns sirens, etc.).
Stop the vehicle before carrying out any operation
that could interfere with your driving.
Do NOT work in extremely high or low temperature.
Be sure the temperature inside the vehicle is
between +60 and -10 before turning on your
unit.
1
PRECAUTION
PRECAUTIONS
Power Supply Requirements
Chassis Dimensions
Maximum Output Power
Safety fuse
DC 12 Volts,
Negative Ground
178x 92x 50 mm
4 x 40W
15 Ampere (max.)
87.5 to 105.0 Mhz
10.7 Mhz
< 10dBu
25 dB
Frequency Coverage
IF
Sensitivity(S/N=30dB)
Stereo Separation
522 to 1620 kHz
450 kHz
35 dBu
Frequency Coverage
IF
Sensitivity(S/N=20dB)
1
1
1
1
2
1
1
Mounting Bracket(Half Sleeve)
Trim plate
Mounting Screw M5
Rubber
Release key
User manual
Wire connector
Note: Due to continuous product improvement,
specifications and design are subject to
change without prior notice.
GENERAL
ACCESSORIES
FM STEREO RADIO
AM STEREO RADIO
SPECIFICATION
CONTENTS
PRECAUTION ........................................................ 1
SPECIFICATION .................................................... 1
FRONT PANEL ....................................................... 2
BLUETOOTH OPERATION ................................... 3
SYSTEM MENU OPERATION............................... 4
INSTALLATION ...................................................... 5
TROUBLE SHOOTING ........................................... 6
FCC WARNING ........... ........................................... 7
> 60 dB
> 55 dB
500 mA
Sensitivity(S/N=30dB)
Stereo Separation
Max loaded current
USB SD CARD
162.4 to 162.5 Mhz
450 kHz
35 dBu
Frequency Coverage
IF
Sensitivity(S/N=20dB)
WB STEREO RADIO
2
1. SRC
Press this button to switch on the unit, press and hold
this button to turn off the unit. .
When the system is on, press this button to switch the
modes available.
In bluetooth mode, press the button to hang up or
reject a coming call.
BAND /
Press
In bluetooth mode, press this button to dial up a call
or receive an incoming call.
In bluetooth mode, press and hold this button to
link up the device and the unit.
VOL
Rotating:
Press and hold this button to display the current
time.
2.
to switch between the radio bands available.
3.
Rotate to adjust the volume level.
Press once:
Press and rotate to select the functions provided.
Following functions can be accessed by press
the volume control knob; in the order specified :
VOL BAL FAD BASS TRE SUBW OFF
Rotate the volume control to change the
setting of these functions.
The Bass and Treble selections are active
only in EQ OFF mode.
4. AF
Press the button to turn on or off the AF function.
/9.
LCD display
8. MENU
Press the button to enter system setup.
Please refer to page 4 for details.
10. 1/
n playback mode
press once: to pause playing,
press and hold: to stop playing.
In radio mode
press once: to select the preset station,
11. 2/
In playback mode, press the button to select the repeat
modes: RPT ONE, RPT DIR, RPT ALL and RPT OFF.
In radio mode
press once: to select the preset station,
12. 3/RDM
In playback mode, press the button to play in random order.
In radio mode
press once: to select the preset station,
5 >>I / I<<
In radio mode, press the keys to search for a station
manually, press and hold to search for a station
automatically.
In playback mode, press these keys to select the track
you want to play. Press and hold to active fast forward
or fast rewind search .
6. MIC
7.
I
press and hold: to store the current station.
press and hold: to store the current station.
press and hold: to store the current station.
FRONT PANEL
MIC
USB
3 RDM 4 5 +
1 2
AUX
IN
BAND
AF
MENU
SRC
1
2
34567
8910 11 12 13 14 15
17
16
5/F-
To go to first song of folder( when an MP3/
WMA is being played).
In radio mode, press to select the preset station.
P
6/F+
next
In radio mode, press to select the preset station.
P
.
17. SD Card slot
previous
Press to go to the first song of the folder
(when an Mp3 / WMA is being played).
. AUX IN
Insert audio cord, press MODE button on the unit
to AUX mode.
USB insert slot
Insert USB device, it will play the files of USB
automatically.
Insert SD card, it will play the files of SD card
automatically.
Note: Once the SD cards could not eject after
pressing, just take it out manually.
13.
ress and hold to store the current station.
14.
ress and hold to store the current station.
15
16
3
FRONT PANEL
General operation
Bluetooth-enabled variant of this radio (BT models) has
additional answer (=accept call) and hang up
(= end/reject call) silkscreen printed on the front panel
buttons.
There is an internal microphone on the front panel.
An optional external microphone may be fitted in
which case the internal microphone is disabled.
Press and hold Answer button activates
last-number-redial.
Pairing
To use Bluetooth handsfree function, a mobile phone
would need to be connected by pairing.
The mobile phone must also have Bluetooth capability.
To pair the mobile phone with the radio, ensure that
the radio is turned on. On the mobile phone, search for
available Bluetooth device. Pair to the device using
passcode1234.
The phone should report to the user pairing has been
successful.
Once paired, many mobile phones are capable of
automatically reconnecting the Bluetooth link so
subsequent pairing is not necessary on these phones.
A2DP and AVRCP
Bluetooth devices that have A2DP functionality can
stream music into the radio. In addition, if the device
has AVRCP, functions like next track and previous track
can be controlled from the radio.
BLUETOOTH OPERATION
4
SYSTEM MENU OPERATION
Menu
On this radio, the 4-level- deep software menu is accessible using the menu button. When accessed, the
LCD displays available menu items. The Reset C confirm entry is to restore default settings.
Short press menu to call up menus. Once in the menu, use the following buttons to navigate:
- menu = EXIT, ESCAPE, MOVE UP ONE LEVEL (to move right to left in the menu tree below)
- Turn rotary knob = PREVIOUS ITEM/NEXT ITEM
(to scroll items <up and down> in the menu tree below )
- Centre button =SELECT ITEM, CONFIRM, MOVE DOWN INTO SUB-LEVEL
(move right to left in the menu tree below)
- Press and hold menu to exit all.
Alternative button is made available by software mapping and is always available:
- right to left >>|
- left to right |<<
Refer the following Software menu tree for the structure of this software menu.
A1 NC
A3 NC
A6 ILL
A4 (+)BATTERY
A5 ANTENNA POWER+
A7 IGNITION KEY
A2 TEL-MUTE
A8 GROUND
B1 REAR RIGHT SPEAKER+
B3 FRONT RIGHT SPEAKER+
B6 FRONT LEFT SPEAKER-
B4 FRONT RIGHT SPEAKER-
B5 FRONT LEFT SPEAKER+
B7 REAR LEFT SPEAKER+
B2 REAR RIGHT SPEAKER-
B8 REAR LEFT SPEAKER- MIC
5
Installation using the screw holes on the sides of the
unit.
First complete the electrical connections,and then
check them for correctness.
182
53
1. Metal Sleeve
Install the metal sleeve in the dashboard.
For optimal performance of the player, the
metal sleeve should be positioned horizontally
(between 10 and +30). Fix metal sleeve into
place by pressing the metal tags outwards using
screwdriver.
2. Front Mounting
Slide the radio into the metal sleeve until the
springs at either side of the radio snap into the
openings of the sleeve.
3. Removing Radio
Insert the levers supplied with the unit into the
grooves at both sides of the unit they lock.
Pull the levers toward you makes it possible to
remove the unit from the dashboard.
Remove the outer rim around the front panel and
the side springs.
Select a position where the screw holes of the
mounting bracket and the screw holes of the radio
become aligned and tighten the screws at 2 places
on each side.
1. Press the release button and pull-off the front
panel. Keep front panel into the case.
2. To install the front panel, insert the panel into the
housing, slide in to the right hand side and push
in till locked.
3. Make sure the panel is properly installed.
Otherwise, abnormalities occurs on the display
or some keys will not function properly.
INSTALLATION PROCEDURES REAR-MOUNT
INSTALLATION OF THE UNIT
REMOVE AND INSTALL THE FRONT PANEL
INSTALLATION
CABLE CONNECTION
Note: A wrong connection can be easily detected by
our technical service for a repair request under the
warranty. Your warranty can be rejected in that case.
6
If any of the problems persist after check list has been made, consult your nearest service dealer.
Symptom Cause Solution
No power. The car ignition is not on.
If the power supply is properly connected to
the car accessory terminal, switch the ignition
key to ACC.
The fuse is blown. Replace the fuse.
No sound.
Volume is in minimum. Adjust volume to a desired level.
Wiring is not properly
connected.
Due to telephone mute.
Check wiring connect.
Ensure your phone MUTE is on.
Sound skips. The music format may be
not correct.
Check if the music format is MP3/WMA.
The operation
key do not
work.
The built-in micro compute
is not operated properly due
to noise.
Front panel is not properly fixed into its
place.
Contacts between front and main unit are
dirty. Clean contacts with a cotton bud
soaked in isopropyl alcohol.
The antenna cable is not work
or connected.
The radio does
not receive the
radio station
automatic
selection does
not work. The Signals are too weak.
Insert the antenna cable firmly.
Select a station manually.
Before going through the check list, check wiring connection.
TROUBLE SHOOTING
1. Keep the product dry. If it does get wet, wipe it dry immediately. Liquids might contain
minerals that can corrode the electronic circuits.
2. Keep the product away from dust and dirt, which can cause premature wear of part.
3. Handle the product gently and carefully dropping it can damage circuit boards and cases,
and can cause the product to work improperly.
4.Wipe the product with a dampened cloth occasionally to keep it looking new. Do not use
harsh chemicals, cleaning solvents, or strong detergents to clean the product.
5.Use and store the product only in normal temperature environment.
High temperature can shorten the life of electronic devices and distort or melt plastic parts.
MAINTENANCE
FCC warning statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum 20 cm between the radiator and your body. This transmitter must not be
collocated or operating in conjunction with any other antenna or transmitter unless
authorized to do so by the FCC.
Changes or modifications not expressly approved by the party responsible for compliance.
could void the user's authority to operate the equipment.

Navigation menu