User Manual
Quick Start Guide Product introduction MDT750 has optional features (WiFi, BT, GPS, 3G, RFID, LoRa, Back camera, Front camera, Video input, GPIO, Lightsensor, Gyroscope, Accelerometer) Highlights: 3G – pls insert the SIM card when the device if complete off front camera – there are 6 IR LED around the camera. if you enable the flash function in front camera, then you will see the IR LED is on. In this case, the picture will be in black and white On/off button Pls move upward to open the cover, you will hear “click” sound, it is normal SD card slot, SIM card slot and reset button Screw hole is available if you want to lock the cover Pls cover it well in order to ensure the waterproof performance Pls move right to open the cover, you will hear “click” sound, it is normal Micro usb for connecting to PC or charging Pls cover it well in order to ensure the waterproof performance All rights reserved. No part of this work may be reproduced or copied in any form or by any means (graphic, electronic, or mechanical, including photocopying, recording, recording taping, or information and retrieval systems) without the written permission of the copyright owner Direction of SIM card and SD card All rights reserved. No part of this work may be reproduced or copied in any form or by any means (graphic, electronic, or mechanical, including photocopying, recording, recording taping, or information and retrieval systems) without the written permission of the copyright owner Interface 1. There is TTL serial port (Tx/RX) or OTG from 10 pin usb connector 10pin usb connector pls see the above schematics of our USB connector in our PND, it is 10 pin connector. Pin 4 and 6 can be used for USB or TTL serial interface (Rx/Tx) and Pin 8 is ID pin which is used to distinguish for USB or serial interface. if it is connected to GND, then the pin 4 and 6 will be Rx/Tx interface. if it is connected to Vcc, then the pin 4 and 6 will be D- and D+. All rights reserved. No part of this work may be reproduced or copied in any form or by any means (graphic, electronic, or mechanical, including photocopying, recording, recording taping, or information and retrieval systems) without the written permission of the copyright owner 2. There are Rs232 interface and OTG from cradle. Highlights: OTG port from device (10pin usb connector) and cradle are sharing same pins. Only 1 OTG interface can be used. Usb connector for OTG or charging This cable can be customized when you placed order For sample, it will be 12 pins connector, pls see below or pins assignment All rights reserved. No part of this work may be reproduced or copied in any form or by any means (graphic, electronic, or mechanical, including photocopying, recording, recording taping, or information and retrieval systems) without the written permission of the copyright owner Pin 1 – NOT connected Pin 2 – GND (black) Pin 3 – RXD (White) Pin 4 – NOT connected Pin 5 – NOT connected Pin 6 – Ignition (Green), it can be wake up the device. see the software section for more details. Pin 7 – 5V input (Pink) Pin 8 – NOT connected Pin 9 – GND (black) Pin 10 – TXD (purple) Pin 11 – car battery input (9-36V) (Red) Pin 12 – NOT connected Highlights: for RS232, it is master mode definition. if you are using OTG with external device, you can only charge the device by 12V input. Removing the cradle cable (12pin molex connector) if you don’t want to use it. 1. you can find the rubber plug in our blackbox (see below picture). 2. open the cradle casing by screw driver 3. remove the 12pin molex cable from connector 4. put the rubber plug in the hole and close the cradle casing Option for ignition control the power supply If ignition is OFF, the power supply will cut. Customer uses their application to control the device to power off or sleep mode. If ignition is ON, there is power supply and able to charge the device. so, when the engine is ON, the device will power on automatically. All rights reserved. No part of this work may be reproduced or copied in any form or by any means (graphic, electronic, or mechanical, including photocopying, recording, recording taping, or information and retrieval systems) without the written permission of the copyright owner If you want to try this feature, pls open the cradle. There are switch inside the cradle PCB. (only production batch >1642) Device installation There are few options 1. Directly attach mount to device (no cradle in this case) 2 screw hole at the back Pls use M4 15mm screw if the mount thickness is 9mm. Pls note that the screw hole depth is only 6mm. Long screw may damge the PCB inside All rights reserved. No part of this work may be reproduced or copied in any form or by any means (graphic, electronic, or mechanical, including photocopying, recording, recording taping, or information and retrieval systems) without the written permission of the copyright owner 2. Cradle attached to car mount with different screw length 2 screw hole at the back Case 1 – if M4 18mm screw is used, the device will be removable from cradle Case 2 – if M4 23mm screw is used, the device will be not removable from cradle Mount options: There are many car mount options. You can use the 2 screw hole (black colour) or 4 screw hole (yellow colour) to attach the different mount system. The 4 screw hole depth is 5mm long only, pls prepare correct screw. Pls note that wrong screw length may damage the cradle. Option 1: All rights reserved. No part of this work may be reproduced or copied in any form or by any means (graphic, electronic, or mechanical, including photocopying, recording, recording taping, or information and retrieval systems) without the written permission of the copyright owner Low cost wind shield car mount Option 2: Many mount option from RAM MOUNT You can choose the mount you like from their website (www.rammount.com) Example 1 (RAP-B-166-2U) Example 2 (RAM-B-138-224-1U) Example 3 (RAM-B-138U-A) All rights reserved. No part of this work may be reproduced or copied in any form or by any means (graphic, electronic, or mechanical, including photocopying, recording, recording taping, or information and retrieval systems) without the written permission of the copyright owner Example 4 (RAP-B-138-AU) Option 3: You can also choose mount from HR (http://www.hr-autocomfort.de/) There are 4 hole plate which you can lock in the cradle with 4 screw hole. then, you can choose the mount from HR. Example 1 (1719/0) All rights reserved. No part of this work may be reproduced or copied in any form or by any means (graphic, electronic, or mechanical, including photocopying, recording, recording taping, or information and retrieval systems) without the written permission of the copyright owner Option 4: Mounting solution from truck expert (ARAT) http://www.arat-de.eu/index.php?ber_id=10&dia_id=1&lang=en Option 5: There are other mount which can support this 2 screw hole and 4 screw hole at the back can be used. For my understanding, there are other mount company also use this 2 or 4 screw hole as standard. Pls let know if you need other mounting system or solution. All rights reserved. No part of this work may be reproduced or copied in any form or by any means (graphic, electronic, or mechanical, including photocopying, recording, recording taping, or information and retrieval systems) without the written permission of the copyright owner 10 New silicon sleeve It can have more protection for the device. 1. It also support stylus. There are optional clip which you can install at the back of the sleeve. 2. There is new cradle (dock) to match the device with sleeve. This cradle can be used for the device with or without the sleeve. All rights reserved. No part of this work may be reproduced or copied in any form or by any means (graphic, electronic, or mechanical, including photocopying, recording, recording taping, or information and retrieval systems) without the written permission of the copyright owner 11 Software support We can provide serial port apk and NFC demo. Pls contact our Sales for details. 1. Pls also see the software setting for serial port two serial ports are available on the device : one shares the the USB data pins of the mini A/B USB connector. Only TX and RX pins are available, voltage is TTL 3.3V. one is on the Pogopin interface (pins 3, 5, 6 and 7). TX, RX CTS and RTS are available, voltage is RS232. On the software side, the tty devices corresponding to these ports are : for the RS232 port, /dev/user_external_tty for the TTL port, /dev/user_tty In addition, one I2C port is available both on the USB and Procopin connectors. The I2C interface is accessible through /dev/user_i2c 2. if your application want to read the ignition state, pls use below API. the 12V input is reported to the application as a key press (high level pressed, low level depressed) in the java Android API, this key is KeyEvent.KEYCODE_TV_INPUT A second way to access the ignition state is to register a broadcast receiver for the action "hk.topicon.intent.action.IGNITION" The current ignition status is given by the extra boolean "state". This intent is sticky, ie the application will be immediately notified of the current status at registration, even if no transition occurred. Here is a code sniplet : private static final String ACTION_IGNITION = "hk.topicon.intent.action.IGNITION"; private BroadcastReceiver mIgnitionReceiver = new BroadcastReceiver() { public void onReceive(Context context, Intent intent) { String action = intent.getAction(); if(!action.equals(ACTION_IGNITION)) return; boolean state = intent.getBooleanExtra("state", false); if(state) Log.d(TAG, "ignition event is on"); else Log.d(TAG, "ignition event is off"); }; All rights reserved. No part of this work may be reproduced or copied in any form or by any means (graphic, electronic, or mechanical, including photocopying, recording, recording taping, or information and retrieval systems) without the written permission of the copyright owner 12 FCC RF Exposure Information and Statement This device meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. The SAR limit of USA (FCC) is 1.6 W/kg averaged. Device types: GPS (FCC ID: 2AHAF-MDT) has also been tested against this SAR limit. SAR information on this and other pad can be viewed on‐line at http://www.fcc.gov/oet/ea/fccid/. Please use the device FCC ID number for search. This device was tested simulation typical 0mm to body. To maintain compliance with FCC RF exposure requirements, the use of belt clips, holsters and similar accessories should not contain metallic components in its assembly, the use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Creator : Keller Sin Description : Title : Business Proposal Comments : Company : Source Modified : D:20180523172905+09'29' Create Date : 2018:05:23 17:29:05+09:00 Creator Tool : WPS Office Modify Date : 2018:09:20 15:08:51+08:00 Metadata Date : 2018:09:20 15:08:51+08:00 Keywords : Producer : Document ID : uuid:54497d73-23cf-433d-b61b-db2ac572cce9 Instance ID : uuid:27f9b10b-227b-4cdb-80de-f200ce6302d1 Page Count : 13 Author : Keller Sin Subject : Trapped : falseEXIF Metadata provided by EXIF.tools