Wild Planet Entertainment MOBILESPYEAR Mobile Spy Ear User Manual 82011UCNoteKitInstrucPG1 AI

Wild Planet Entertainment, Inc. Mobile Spy Ear 82011UCNoteKitInstrucPG1 AI

User Manual

OPERATING MOBILE SPY EAR VEHICLE 1. Slide SWITCH on VEHICLE to ON position. RED LED will light.2. Place vehicle in the room you would like to listen in, OR send it in to spy.3. To send vehicle in to spy, place it on the floor, making sure both rear wheels are contacting the floor.4. Pull back the vehicle to wind the motor, point vehicle in the direction you want to go, then let go. For maximum distance, pull the vehicle back until you hear the clicking “ratchet” sound, indicating the motor is fully wound. • Tip: Vehicle will travel farther on hard floors than on carpet.• Always turn power off when not in use to preserve battery life.OPERATING LISTENING RECEIVER1. Move up to 75 feet (23 meters) from the vehicle.2. Rotate the POWER/VOLUME CONTROL to turn on the power. RED LED will light. Set volume to a low level to start. 3. Unsnap EAR BUD, unwrap CORD, and place ear bud in your ear.4. SLOWLY turn volume up until you can hear.• Always turn power off when not in use to preserve battery life.CONNECTING/CARRYING ON BELT CLIP1. Turn off the power on both units.2. Wrap cord around CORD SPOOL, snap ear bud into HOLDER.3. Push CONNECTOR on receiver into SLOT on vehicle. 4. Secure ANTENNA under CLIP on either side of cordspool. (Fig. 1)5. Hang connected units on your belt using BELT CLIP.ADULTS: REPLACING BATTERIES1. Using a small Phillips screwdriver, loosen screw and remove BATTERY DOOR on each unit. (Figs. 2 and 4) 2. Remove both old batteries.3. Snap a fresh, new battery onto each BATTERY CLIP. (Fig. 3) IMPORTANT: Observe battery polarity (+ and – )4. Place each battery into battery compartment, making sure wires and clip are tucked neatly inside.5. Replace battery covers and tighten screws.BATTERY SAFETY1. Only adults should install and replace batteries. 2. Do not recharge non-rechargeable batteries. 3. Remove dead or exhausted batteries. 4. Insert batteries correctly. Match positive and negative signs. 5. The supply terminals are not to be short circuited. 6. Do not use rechargeable batteries. 7. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. 8. Do not mix old and new batteries. 9. Only the batteries of the same or equivalent type recommended to be used. Mobile Spy EarListening Device in a Pull-Back VehicleAges 6 and Up70181Requires 2 9V (6LR61) batteries,not included.Important: Please save this instruction sheet. It contains valuable product information.TMTMMOBILE SPY EAR 70181-4000 PR 3/07IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT US AT1-800-247-6570WWW.WILDPLANET.COM/HELPWild Planet Entertainment, Inc., P.O. Box 194087San Francisco, CA 94119-4087TM© 2006 Wild Planet Entertainment, Inc., San Francisco, CA 94104, USA. All rights reserved. PRINTED IN CHINA.Product specifications subject to change. Caution: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.FCC ID: N3EMOBILESPYEARThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.AntennaAntennaclipFig. 1Fig. 3BatteryclipFig. 2VehiclebatterydoorFig. 4ReceiverbatterydoorRECEIVERVEHICLERed LEDMicrophonePowerSwitch(underside)Ear budHolderCord spoolPower/volumecontrolBelt clip(on back)ConnectorSlotONOFFRed LEDNOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installion. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installion. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.

Navigation menu