Zhuhai Unitech Power Technology IKEYMU-1 Smart Key User Manual Smart Key
Zhuhai Unitech Power Technology Co., Ltd. Smart Key Smart Key
Users Manual
User Manual for iKeyMU-1_F Smart Key
Document No.: TSS-iKeyMU1_F-001
Version No.: V1.0
IKEYMU-1_F SMART KEY
USER MANUAL
Total 43 Pages
Formulated by: Liu Xiaojun
Audited by: Yang Shaohua
Reviewed by: Xu Yinhua
Countersigned by: Ma Jinhui
Approved by: Li Baofu
Zhuhai Unitech Power Technology Co., Ltd.
Sept. 7
th, 2011
User Manual for iKeyMU-1_F Smart Key
.Contents
1OVERVIEW............................................................................................................................................1
2APPEARANCEANDCOMPONENTFUNCTIONS................................................................................................2
3FUNCTIONSANDPERFORMANCES..............................................................................................................4
4TECHNICALPARAMETERS..........................................................................................................................6
5OPERATION...........................................................................................................................................7
5.1ElementaryOperation................................................................................................................7
5.1.1Start.........................................................................................................................................7
5.1.2Close.....................................................................................................................................................7
5.1.3PreparationbeforeOperation.............................................................................................................8
5.1.4MenuOperation..................................................................................................................................8
5.1.5ShortcutMenu....................................................................................................................................9
5.2Self‐Learn....................................................................................................................................9
5.3ReceiveOperationOrders.........................................................................................................10
5.4Unlock.......................................................................................................................................12
5.4.1UnlocktheDevicesLockedbyMechanicalCodingLocksSuchasManualDisconnector,
Grounding‐switch,andTemporaryGroundingConnector.........................................................................12
5.4.2UnlocktheDevicesInterlockedbyCircuitLocksSuchasCircuitBreaker,ElectricDisconnector,etc.
...................................................................................................................................................................14
5.4.3UnlocktheDevicesInterlockedbyCircuitLockandMechanicalCodingLockSuchasElectric
Disconnector...............................................................................................................................................15
5.4.4UnlocktheNon‐mandatorilyLockedDevices....................................................................................16
5.4.5StateDetection..................................................................................................................................17
5.4.6ElectriferousDetection......................................................................................................................17
5.4.7UnlocktheDevicesSimultaneouslyLockedbytheControlSystems(SuchasKBQ)ExceptSmartKey
andMimicPanel.........................................................................................................................................18
5.4.8UnlocktheDevicesLockedbyFeedbackCircuitLocks......................................................................20
5.5PostBack..................................................................................................................................21
5.5.1NormalPostback...............................................................................................................................21
5.5.2SuspensionPostback.........................................................................................................................22
5.5.3RecallingPostback.............................................................................................................................22
5.6BrowseOrders..........................................................................................................................23
5.6.1BrowseOrderContents.....................................................................................................................23
5.6.2BrowseRecall....................................................................................................................................23
5.7Accessibilities............................................................................................................................24
5.7.1Self‐Learning......................................................................................................................................24
5.7.2CheckCode........................................................................................................................................24
5.7.3SpecialOperations.............................................................................................................................25
5.7.3.1SmartUnlock..................................................................................................................................25
5.7.3.2Skip.................................................................................................................................................25
5.7.3.3OnlineUnlocking............................................................................................................................26
User Manual for iKeyMU-1_F Smart Key
5.7.3.4DeleteOrders.................................................................................................................................27
5.7.4FunctionalTest..................................................................................................................................27
5.7.4.1VoiceTest........................................................................................................................................28
5.7.4.2BuzzerTest ......................................................................................................................................28
5.7.4.3IRDACommunication.....................................................................................................................29
5.7.5Debugging.........................................................................................................................................29
5.7.6TestforProduction............................................................................................................................30
5.8SystemSettings.........................................................................................................................30
5.8.1CommunicationMode.......................................................................................................................30
5.8.2CommunicationParameters..............................................................................................................31
5.8.3VoiceSettings....................................................................................................................................34
5.8.4BacklightBrightness..........................................................................................................................35
5.8.5TimeSettings.....................................................................................................................................35
5.8.6BackgroundSettings...........................................................................................................................36
5.8.7SmartUnlocking................................................................................................................................37
5.8.8RemoteOperation.............................................................................................................................37
5.8.9NetworkSettings...............................................................................................................................37
5.9Help..........................................................................................................................................38
6SPECIALFUNCTIONS..............................................................................................................................39
6.1AutoPower‐off.........................................................................................................................39
6.2ShortcutMenu..........................................................................................................................39
6.3ScreensaverinCharging...........................................................................................................39
6.4Outdoor/IndoorMode..............................................................................................................40
7PRECAUTIONSINOPERATING..................................................................................................................41
8TROUBLESHOOTING...............................................................................................................................42
9WARNING...........................................................................................................................................43
User Manual for iKeyMU-1_F Smart Key
1
1 Overview
The iKeyMU-1_F midsize smart key is a new type of OLED color-screen smart key
based on the “Double-less” technology of the company, which can be operated in
conjunction with JOYO series of microcomputer safety interlock systems. The
“Double-less” technology is a new acquiring and coding technique developed by the
company under huge investments, which has gained many patents and is especially
applicable to the microcomputer anti-maloperation field, characterized by limitless coding
and wireless acquiring.
The iKeyMU-1_F smart key has an essential improvement, no matter in technology,
performance, and manufacture process, compared with the previous type of smart key,
and it is capable of meeting the customer’s new requirements on five-prevention devices
such as the applications in centralized control station.
Note: CDMA module will be unavailable about this product.
User Manual for iKeyMU-1_F Smart Key
2
2 Appearance and Component Functions
Figure 1：Appearance Diagram of iKeyMU-1_F Smart Key
1 ------- Smart key housing;
2 ------- Speaker hole;
3 ------- Keys, including the Return key (the Switch on/off key), the Up key, the Down
key, and the Enter key represented by On / Off, Up, Down, and Enter.
4 ------- 60,000-dot OLED color screen: displaying the operation information by
Chinese characters and graphics information;
5 ------- High-speed IRDA transmission link for data exchange with host;
6 ------- Transmission locating key: conductive electrode for circuit lock;
7 ------- Wireless sensor: detecting the lock code;
8 -------Release rod: release the mechanical coding lock, or used as conductive
electrode for circuit lock;
9 ------- Unlocking button: press the key to rotate the release rod clockwise, to unlock
mechanical coding lock;
10 ------ Infrared photoelectric detector;
User Manual for iKeyMU-1_F Smart Key
3
11 ------ Battery locking knob;
12 -------High-capacity poly-lithium rechargeable battery;
13 ------ Battery cover label;
14 ------ Charger electrode;
User Manual for iKeyMU-1_F Smart Key
4
3 Functions and Performances
Limitless coding; and the coding system adopts the GUID;
Wireless code acquiring; the smart key adopts the non-contact acquisition mode.
Receiving several operation orders available;
“Black Box” function: Recording and browsing the operation orders and the operation
information; the data can be well saved within 10 years after power-off;
The smart key functions as order clearance, self-learning, memory, lock code
checking, termination of the current operation order, step-skipping, real-time clock,
battery electric quantity detection, self-diagnosis, etc.
It can release and detect various locks as follows:
Mechanical coding lock
circuit lock
Feedback circuit lock
Electric control lock
Fixed lock
Super smart anti-empty application lock
Electroscope
State detector
The system is provided with various advanced data transmission modules such as
high-speed infrared IRDA module, wireless UT-NET communication module, CDMA
module, etc., which can be matched according to the customized requirements.
Voice prompt in mandarin;
Sixty thousand dots OLED color screen to enhance the visual effects.
Friendly man-machine interface and on-line help system for your convenient and
simple operation.
Automatic power control (APC) and automatic detection of battery fault for a low
power consumption of system to prolong the service life of battery;
User Manual for iKeyMU-1_F Smart Key
5
Ultra-low temperature poly-lithium battery with independent encapsulation design;
Supporting all the Chinese character databases stipulated by GB2312;
Strong resistance to ultra low temperature (-40℃); high contrast, and multi-line
Chinese character displayer.
Brightness adjustable in OLED displayer for different demands from users;
Super capacity memory; expandable as needed;
Flexible switchover between manual operation mode and automatic operation mode;
Developed based on the Real-Time Operating System (RTOS); high stability;
convenient extension;
Integrated mechanism and overall metal frame design to enhance its fall resistance
and impact resistance;
Brand new structure integrating functions such as code acquisition, detection and
releasing mechanical lock, for a simple and convenient operation and the
improvement on the stability, reliability and producibility.
User Manual for iKeyMU-1_F Smart Key
6
4 Technical Parameters
Ambient Temperature: -40℃～+70℃
Environment Relative Humidity: Daily Mean≤95%, Monthly Mean≤90%
Power Source: 4.2V High Capacity Rechargeable Lithium Ion Battery
Static Working Current: ≤25mA
Unlocking Maximum Current: ≤300mA
Numbers of Identification Code Lock: ≥65535
Allowable Current Through Operating Circuit: 1mA～5A
Antistatic Strength: ≥8000V
Radio Frequency Interference Resistance Strength: ≤50db（uV/m）
Power Terminal Transmission Interference Resistance Strength: ≤70db（uV）
Impact Strength: ≥6g
Operating Circuit Rated Voltage: ≤220Ｖ AC, DC
Environment Infrared Resistance Strength: No Less Than 0.8mW/cm2 When
Wave Length is 850～980nm
ZIGBEE Operating Frequency Range: 2420~2460 MHz
ZIGBEE Antenna Gain: 3dbi
ZIGBEE Output Power: 18±3dBm
Receiving Operation Content at One Time: ≤3000 Frames
Operation Order Storage Capacity: ≤4MB
Outline Dimensions: 132×72×31mm
Mean Time between Failures (MTBF): 50000h
Grade of Rainproof and Dustproof Can Reach Requirements of IP65 Specified in
GB 4208-84
User Manual for iKeyMU-1_F Smart Key
7
5 Operation
5.1 Elementary Operation
5.1.1 Start
① Ensure that the smart key is available to be powered. If the battery runs low, the
smart key can’t start, please operate in accordance with the second step.
Place the smart key on the charger and check if it is properly placed and is stably ②
connected to the charger.
Press the on / off ③key on the panel, and then release it, the smart key produces
“Beep” sound and displays the dynamic LOGO on the interface, and shows the
following standby interface later:
Thereinto:
“ “ is a symbol of battery, indicating the current running level of the battery,
the full-green color indicates that the battery runs in full level; the full-white color
indicates that the battery runs out. When the battery symbol is full-white, namely the
battery runs out, please charge the battery immediately.
5.1.2Close
It is available to close the smart key at any state after starting. A user can press and
hold down the On / Off key on the panel for about 3 seconds, the smart key produces the
sound “beep…beep…”, then the user can release the key, the key can switch off the
power supply automatically. In addition, the key can also be closed by shortcuts: press the
Enter key on the standby interface, select the Close option on the shortcut menu, and
press the Enter key to close the key quickly.
User Manual for iKeyMU-1_F Smart Key
8
5.1.3 Preparation before Operation
The iKeyMU-1_F smart key is a general-purpose smart key, which can be applied to
any station, and it is required to enable the “self-learning” function before operation, thus
to transmit the station's device information to the smart key. If the device information is not
modified in a station, the smart key can be used forever as long as enabled “self-learning”.
5.1.4 Menu Operation
In the standby interface, press the “Main Menu” option to enter main menu as shown
below:
Thereinto:
The “Receive Order” is the default option on the menu, indicating the option is selected.
Now a user presses the Down key to select the next option on the menu, similarly, it is
available to press the Up key to select the previous option.
When selecting an option on the menu, press the Enter key to enter the function menu
interface or the submenu interface; press the Cancel key to the standby interface or the
option's parent menu.
When a user operates on a submenu, it can display the scroll bar icon on the right side
of the screen, to show the current position of the selected submenu. There is a help
prompt box on the lower right side of each submenu, to give a brief introduction to the
contents or functions of the menu.
User Manual for iKeyMU-1_F Smart Key
9
5.1.5 Shortcut Menu
1) In the standby mode, press the Enter key to the shortcut menu as shown below:
Now, take the “Voice” menu as an example, select and press the Enter key to
display the following interface:
In this page, a user can enable or disenable voice quickly and easily.
5.2 Self-Learn
The smart key features good interchangeability and versatility, it can be applicable to
different substations or power plants once successfully self-learned before the first
operation.
Under the IRDA communication mode, it is available to receive self-learning data
directly in the standby interface, or select “Accessibility” on the main menu, and then
select the “self-learning” option to directly enter the self-learning interface; the key can
receive the transmitted self-learning data atomically. Under the UT-NET communication
mode, the key prompts the information such as “connecting to the wireless network, GET
MAC ...,” when the UT-NET initialization is completed, it can enter the self-learning
interface.
User Manual for iKeyMU-1_F Smart Key
10
Thereinto:
Press the Return key to the previous menu。
1) Under the UT-NET communication mode, a user can just set the master station to
the self-learning state to enable the key to receive self-learning data.
2) Under the IRDA communication mode, a user needs to set mimic panel (or
synthetic operation interface and other devices) to self-learning state, and then aim
the smart key at transmission port of transmission adapter, and keep a distance
within 1.2 meters, the key can receive self-learning data.
3) When the key is being charged on the transmission adapter, regardless of
UT-NET mode or IRDA mode, the key can receive self-learning data if the user sets
Model IV host or mimic panel to (or synthetic operation interface and other devices)
to the self-learning state, and the smart key enters the self-learning interface.
When the key starts receiving self-learning data, it can display the following interface,
the progress bar shows the receiving progress of self-learning data.
When the self-learning data have been received, the smart key is capable of
processing and saving the received data.
5.3 Receive Operation Orders
A user can press the Up or Down key to select the option “Receive Orders” on the
main menu, and press the Enter key, if the communication mode is UT-NET, the key
User Manual for iKeyMU-1_F Smart Key
11
prompts the information such as “connecting to the wireless network, GET MAC ...,” when
the UT-NET initialization is completed, it can enter the order-receiving interface. If the
communication mode is IRDA, the key can enter order-receiving interface directly.
Thereinto:
If the key hasn’t self-learned, it can not enter the order-receiving interface, the screen
displays the information “the key hasn’t self-learned”, and a user must conduct
self-learning before receiving orders.
Press the On / Off key to the main menu.
1) Under the UT-NET communication mode, a user can just set the master station to the
order-sending state to enable the key to receive orders.
2) Under the IRDA communication mode, a user needs to set mimic panel (or synthetic
operation interface and other devices) to order-sending state, and then aim the smart key
at transmission port of transmission adapter, and keep a distance within 1.2 meters, the
key can receive orders.
3) When the key is being charged on the transmission adapter, regardless of UT-NET
mode or IRDA mode, the key can receive orders if the user sets Model IV host or mimic
panel to (or synthetic operation interface and other devices) to the order-sending state,
and the smart key enters the order-receiving interface.
When the key starts receiving order data, it can display the following interface, the
progress bar shows the receiving progress of order data.
User Manual for iKeyMU-1_F Smart Key
12
When the smart key has processed and saved the received data, the key can switch
to the following operating interface automatically.
A user can operate on site now in accordance with the displayed content.
5.4 Unlock
5.4.1 Unlock the Devices Locked by Mechanical Coding Locks Such as
Manual Disconnector, Grounding-switch, and Temporary Grounding Connector
The smart key can display the specific device information under operating while
unlocking the mechanical coding locks such as manual disconnector, grounding-switch,
and temporary grounding connector, web door, etc. For example, if a user wants to “close
the No. 101 switch”, the key can display the following information at this moment:
User Manual for iKeyMU-1_F Smart Key
13
Find the corresponding device matched with the displayed by the key on site, and
insert the smart key into the keyhole, if the code is correct, the smart key can ring “beep”
or make a voice prompt “Correct, Please Operate!” (Available to set in the system) and
display as follows:
Press the Unlocking button to open the mechanical coding lock at this moment and
then switch.
When the correct operation is completed, the smart key can ring “beep” and prompt
as follows:
Then the operator can continue the next operation.
Note: If the inserted lock’ code is not consistent with the displayed in the key, the key
can ring “beep” three times or make a voice prompt “Wrong Code, Please Check!”
(Available to set in the system) and display below, the above is the same to other types of
locks.
User Manual for iKeyMU-1_F Smart Key
14
At this moment, the operator can’t unlock because the interlocking gear is locked.
5.4.2 Unlock the Devices Interlocked by Circuit Locks Such as Circuit Breaker ,
Electric Disconnector, etc.
When the smart key displays the device information of circuit breaker or electric
disconnector, please insert the smart key into the circuit lock of corresponding device, it
can ring “beep ” or prompt by voice “Correct, Please Operate!” (Available to set in the
system) and display “Correct Code, Please Operate!”
Switch the breaker at this moment, the key rings “Beep” and displays “the operation is
completed, please continue!” indicating that the key has detected the completion signal,
as shown as below:
It is available to unplug the smart key and continue.
If the key is unplugged when it has not detected the complete operation signal within
2 seconds under the operation of circuit lock, it can show that the default key “failure” is
white, and the other key is “success” as shown as below:
User Manual for iKeyMU-1_F Smart Key
15
Press and hold down the “success” or “failure” key (for 2 seconds) to select the
operating results, “success” indicates that this step is complete, the key can enter the next
step; “failure” indicates that this step is not completed and will be restarted.
If the key is unplugged when it has not detected the complete operation signal over 2
seconds under the operation of circuit lock, it can show that the default key “success” is
white, and the other key is “failure” as shown as below:
Press and hold down the “success” or “failure” key ( for 2 seconds) to select the
operating results, “success” indicates that this step is complete, the key can enter the next
step; “failure” indicates that this step is not completed and will be restarted .
5.4.3 Unlock the Devices Interlocked by Circuit Lock and Mechanical Coding
Lock Such as Electric Disconnector.
When the smart key displays the information of the devices to be operated, please
insert the smart key into the circuit lock or mechanical coding lock of corresponding device,
it can ring “beep…” or prompt by voice “Correct, Please Operate!” (Available to set in the
system) and display “Correct Code, Please Operate!”
User Manual for iKeyMU-1_F Smart Key
16
A user can operate circuit lock or mechanical lock as needed, then the user should
insert the corresponding locks and press the Unlocking button to unlock, the smart key
rings “beep” and displays the following information:
It indicates that the smart key has completed its working; the user can remove the
smart key and continue the next operation.
While inserting the corresponding circuit lock, it is available to operate in accordance
with the steps described in “5.4.2 Unlock the Devices Interlocked by Circuit Locks Such as
Circuit Breaker, Electric Disconnector, etc.”
5.4.4 Unlock the Non-mandatorily Locked Devices
When the smart key displays “prompt”, “check”, “second operation” and other
information require operating a device, indicating the device number represents a
non-mandatory locked device, it is available to directly enter switching operation, after the
operation is completed , press the Enter key to check the prompt, and then release it, as
shown as follows:
User Manual for iKeyMU-1_F Smart Key
17
5.4.5 State Detection
The smart key shows the state of the device to be detected, please find the
corresponding connection or disconnection state detectors, electrical switching state
detectors in accordance with the device number shown on the smart key, and insert the
smart key; the smart key can continue its working only after detecting the correct state.
5.4.6 Electriferous Detection
Insert the smart key into the corresponding electroscope for further electriferous
detection, when the smart key displays electriferous detection and the next option, then
enter mechanical lock operation after the electriferous detection is successful, if the
mechanical lock code is correct, and the operation is successful, it is available to enter the
next step.
User Manual for iKeyMU-1_F Smart Key
18
When the smart key displays the following information in the detecting process:
And produces rapid alarm sound “Beep…Beep…Beep…”indicating the circuits are
electriferous, and can’t enter the next operation.
When the smart key displays the following information, and rings “Beep”, it indicates
that the circuits aren’t electriferous, remove the smart key from the electroscope and enter
the next operation.
5.4.7 Unlock the Devices Simultaneously Locked by the Control Systems
(Such as KBQ) Except Smart Key and Mimic Panel.
Except smart key and mimic panel, (or synthetic operation panel), the control
systems (such as KBQ, monitoring system, etc.) are not the prior locking devices.
When the smart key is used in conjunctions with such the devices, the smart key can
display:
User Manual for iKeyMU-1_F Smart Key
19
At this moment, It is available to insert the smart key back into the adapter (or
integrated operation interface, transmission port, etc.) to control unlocking and other
operations by such the devices, or use the smart key to unlock.
① Use mimic panel (or integrated operation panel) in conjunctions with other devices.
Press Enter key to display:
Aim the smart key to the transmission port, and it shows later:
Send the operating results back to the smart key after the operation by other devices,
if the unlocking is successful, the smart key can produce “Beep” twice, automatically load
and display the related operating information; if the above devices fail to unlock, the key
returns to the starting state automatically, then please unplug the smart key and use it to
User Manual for iKeyMU-1_F Smart Key
20
unlock, see details in the section “② Unlock with the smart key.”
②Unlock with the smart key
If use the smart key to unlock the device, please refer to the operation methods for
circuit or mechanical coding lock.
5.4.8 Unlock the Devices Locked by Feedback Circuit Locks
When the smart key shows the number for the device to be operated, please insert
the smart key into the device's feedback circuit lock; at first, the smart key can check if the
current state of the device is correct, if incorrect, the smart key can display the related
information, the smart key must be unplugged at this time, please do not continue any
operation until the current device is in the correct position.
The operation steps of Circuit Locks can be performed in accordance with the
operating procedures described in “5.4.2 Unlock the Devices Locked by the Circuit Locks
Such as Circuit Breaker, Electric Disconnector, etc.
When the operation is completed, the smart key can check if the position is correct,
the key can prompt “detecting feedback, please insert the key well!” The display interface
is shown as follows:
If the key detects that the device is correctly switched, the smart key can display the
following information, the operator can pull out the smart key, then the operation is
completed, the smart key continues to display the content of the next operation.
User Manual for iKeyMU-1_F Smart Key
21
If the smart key doesn’t check the correct connection, the smart key displays the
following image to inform the operator that the current device is not switched, please
check it, then the operator must check if the current device is in the correct position, if the
device is not in the required position, please find the reason, and switch the device to the
correct position, then press the Unlocking button on the smart key, the smart key can
continue to show the next operation, then the operator may continue the next operation.
5.5 Post Back
The data postback is a transmission process of the operation processes and results
and other information from the smart key to the mimic panel, (or integrated operating
panel, etc.) which is mainly divided into three types: the normal postback at the end of an
operation, suspension postback during operation process, recalling information postback.
5.5.1 Normal Postback
When the key completes the current operation order, it will automatically prompt the
postback information on the completion of operation, Under the UT-NET communication
mode, the key prompts the information such as “connecting to the wireless network, GET
MAC ...,” when the UT-NET initialization is completed, it can directly prompt the message
“waiting for the postback data.” If the key is closed before postback, it can prompt such
information again automatically when it restarts; the normal postback interface is shown
User Manual for iKeyMU-1_F Smart Key
22
as follows:
5.5.2 Suspension Postback
Suspension postback refers to a postback when the operation order has not been
completely executed. Select the Main Menu- Postback - Suspension Postback to enter
the option. If the operation orders are fully executed, it can prompt that “all operation
orders have been operated, it is unavailable to post back now”. after entering the option, if
the communication mode is UT-NET, the key can prompt the information such as
“connecting to the wireless network, GET MAC ...,” when the UT-NET initialization is
completed, it can directly prompt the message “waiting for the suspension postback.” if the
communication mode is IRDA, it can directly prompt “waiting for the suspension
postback.” It is available to execute the postback if the mimic panel (or the integrated
operation panel) is being in the postback state. it can return to the main menu
automatically; the suspension postback interface is shown as follows:
5.5.3 Recalling Postback
Recalling postback is a postback of recalling information saved in the smart key.
Select the Main Menu- Postback - Recalling Postback to enter the option. The version
of software does not support this feature currently; the corresponding interface is shown
as follows:
User Manual for iKeyMU-1_F Smart Key
23
5.6 Browse Orders
5.6.1 Browse Order Contents
The order browsing functions as browsing and checking the content of the current
operating order in the smart key. Select the Main Menu- Browse Orders - Browse Order
Contents to enter the option. If the smart key has not any operating order, it will prompt
“no order now, unavailable to browse”, if the smart key has received the operating order,
press the Enter key to show the contents on the first item of the current operation order.
Press the Down key to show the contents of the next item, press the Up key to select the
content of previous item, as shown below. Press the Return key to the previous menu.
5.6.2 Browse Recall
The option is to browse and check the content of the recalling data in the smart key.
Select the Main Menu- Browse Orders – Browse Recall to enter the option. If the smart
key has not received any operating order, it will prompt “no recall data now, unavailable to
browse”, if the smart key has received the recalling data, press the Enter key to show the
content on the first page of the recall records. Press the Down key to select the contents of
the next page, press the Up key to select the content of previous page, and press the
Enter key to browse the currently-selected page, as shown below.
User Manual for iKeyMU-1_F Smart Key
24
5.7 Accessibilities
5.7.1 Self-Learning
See details in the section 5.2 Self-Learning.
5.7.2 Check Code
The option is to check the code value or RFID value of the current lock. And it is also
capable of showing the corresponding device name. Select the Main Menu-
Accessibilities –Check Code to enter the option, press the Enter key to read the lock
code or RFID code value. The code’s equipment name can be shown if exists. If the
device name doesn’t exist, it can show “no the character code for the device”. Press the
Return key to the previous menu. The interface is shown as follows:
User Manual for iKeyMU-1_F Smart Key
25
5.7.3 Special Operations
5.7.3.1 Smart Unlock
Select Special Operations-Smart Unlock, the smart key shows as follows:
At this moment, insert the skipping key to enter skipping verification process, if
validated, it is available to continue smart unlocking operation.
5.7.3.2 Skip
Skip operation can be defined as to skip the option (that has been forcedly operated)
currently displayed on the smart key when the lock is abnormal and is unavailable to be
unlocked by the smart key, and requires forced unlocking by approval of the director in
charge, thus continuing the next operation.
Enter Special Operation - Skipping, the smart key displays as follows:
At this moment, insert the smart key step into the skipping key, the smart key begins
User Manual for iKeyMU-1_F Smart Key
26
to identify the skipping key, 5 seconds later, the smart key displays as follows:
If fails, the key displays:
Please remove the smart key from the skipping key when the skipping operation is
successful, the smart key loads the next operation automatically, and continues its
operations.
5.7.3.3 Online Unlocking
Enter Special Operation – Online Unlocking, the smart key displays as follows:
Please verify your ID card，and it is available to continue if your ID is passed.
User Manual for iKeyMU-1_F Smart Key
27
5.7.3.4 Delete Orders
If doesn’t want to operate an received operating order or post the result back, a user
can press the Up or Down key to select -Special Operation-Delete Orders, and press
Enter key, the key will show the following interface:
Thereinto:
Press the Enter key to delete the order, the smart key will automatically return to
the main menu; or press the Return key to directly return to the main menu,
rather than to delete the operation order.
5.7.4 Functional Test
On the main menu, the option “Functional Test” provides a series of tests for the
functional parts, and aims to check the normality of each function. The “Functional Test”
menu consists of there options, called the sub-menus of “functional test”. In the function
test, the smart key displays the interface below, a user can operate it as same as
operating the main menu to select the functional part to be tested. On the interface, a user
can press the Return key to the previous menu.
User Manual for iKeyMU-1_F Smart Key
28
5.7.4.1 Voice Test
A user can press the Up or Down key to select the “Voice Test” option on the menu
“Functional Test”, the option is mainly used to test the voice system of the smart key, press
the Enter key to enter the voice test state, the smart key displays as follows:
Press the “Enter” key to continue other voice tests. Press the “On / Off” key to the
previous menu.
5.7.4.2 Buzzer Test
A user can press the Up or Down key to select the “Buzzer Test” option on the menu
“Functional Test”, the option is mainly used to test the normality of built-in buzzer, press
the Enter key to enter the buzzer test state, the smart key displays as follows:
User Manual for iKeyMU-1_F Smart Key
29
On this state, the smart key can automatically produce beep sound from high to low
tone every other 600 milliseconds, and repeat such14 tones. A user may press the Enter
key or the Return key to the sub-menu at any time.
5.7.4.3 IRDA Communication
Press the Down or Up key to select the “IRDA Communication” option on the menu
“Functional Test”; this option is mainly used to test the normality of IRDA, press the Enter
key to enter the test state.
5.7.5 Debugging
This menu provides a series of debugging programs special for professional test
personal, and such test options are unavailable to final users for further safe and reliable
operations.
If a user enters the menu, the key will display an interface for inputting password, the
user can ignore it, or press the Cancel key to the previous menu, the operating interface is
as shown as below:
User Manual for iKeyMU-1_F Smart Key
30
5.7.6 Test for Production
The menu provides a series of testing programs special for production, and such test
options are unavailable to the final users for further safe and reliable operations.
If a user enters the menu, the screen will display an interface for inputting password,
the user can ignore it, or press the Cancel key to the previous menu, the operating
interface is as shown as below:
5.8 System Settings
5.8.1 Communication Mode
Communication mode can be defined as the approach (such as self-learning,
receiving orders, data postback, etc.) for communication between the smart key and
other devices requiring data transmission, including IRDA, CDMA, and UT-NET. This
menu functions as changing its communication modes; Select the System
Settings-Communication Mode to enter the menu, and then input your password.
After entering this menu, press the arrow keys to select the communication mode,
press the Enter key to save the selected communication mode. Press the Return key
to the previous menu.
User Manual for iKeyMU-1_F Smart Key
31
5.8.2 Communication Parameters
The communication parameters include CDMA and UT-NET parameters.
Select the UT-NET, press the Enter key to the corresponding parameter settings,
including wireless ID, P2P Address, P2P monitoring, network settings and offline settings.
The wireless ID is the unique parameter indicating the identity of the key,
including 16-bit numbers. P2P address functions as communicating with the
monitoring key under the monitoring mode of midsized key. P2P monitoring functions
as enabling and disenabling monitoring function. Network settings can set UT-NET
modes including non-network mode, network mode, and gateway mode. Offline
settings function as set the current operation mode including online or offline mode.
CDMA parameter settings include server IP, server port, login user, login
password, international ID, PPP connection, authentication, Permissions settings,
and operation mode.
User Manual for iKeyMU-1_F Smart Key
32
Server IP: Set the IP address of the server.
Server port: Set the server's port number in communication.
Login user: identify the ID of a user.
User Manual for iKeyMU-1_F Smart Key
33
Password: set the user's password.
International ID: set IMSI number of CDMA card. PPP connection: Set PPP
connection address in test of CDMA mode.
Authentication: enable and disenable the identification function of user name.
Permission Settings: set the permissions under CDMA mode, including default,
PAP and CHAP a.
User Manual for iKeyMU-1_F Smart Key
34
Operation Mode: set the continuous and discontinuous modes under the CDMA
communication mode.
5.8.3 Voice Settings
The menu functions as modifying voice-related parameters, including voice
settings, volume settings, recording module, enable recording, and Electroscope
voice.
Voice Settings: enable or disenable voice; when the voice is enabled, the key
can make voice prompts, and the buzzer doesn’t work; when the voice is disenabled,
the buzzer can make prompts, and the key can’t make any voice prompt. After
entering this menu, press the arrow keys to enable or disenable voice, press the Enter
key to save the current voice state. Press the Return key to the previous menu. The
interface is as shown as follows:
The key doesn’t support the Volume Settings now. The Enable Recording and
Recording Module are only available to the recording key, and used for enabling or
disenabling recording function. Electroscope Voice functions as enabling or
disenabling the voice prompts including “charged, prohibited to operate” and
User Manual for iKeyMU-1_F Smart Key
35
“uncharged, available to operate”, when the electroscope runs.
5.8.4 Backlight Brightness
The menu functions as setting backlight brightness, Select System Settings -
Backlight Brightness on the main menu, to enter the menu. Press the arrow keys to
increase or decrease the backlight brightness; press the Enter key to save the current
backlight brightness level. Press the Return key to the previous menu.
5.8.5 Time Settings
The menu functions as setting time and date, Select System Settings –Time
Settings on the main menu, to enter the menu, as shown as below. Press the Down key
to select the items to be adjusted; press the Up key to adjust the current option, press the
Enter key to save the current state. Press the On / Off key to cancel the operation and
directly return to the previous menu.
User Manual for iKeyMU-1_F Smart Key
36
5.8.6Background Settings
The menu functions as setting the background pattern of the user interface, Select
System Settings –Background Settings to enter the menu, as shown as below. Press
the Up or Down key to select the background image, press the Enter key to set, press the
On / Off key to cancel the operation. The currently available backgrounds are three
options as follows:
Note: it is recommended to use the black background in consideration of the visibility
of information for the operation and power saving.
User Manual for iKeyMU-1_F Smart Key
37
5.8.7 Smart Unlocking
The menu functions as setting the smart unlocking options, Select System Settings
–Smart Unlocking to enter the menu. After entering this menu item, press the Up or
Down key to select the options, press the Enter key to enter the submenu, press the Enter
key to save the current option, and then return to the previous menu. Press the Cancel
key to cancel the modification and directly return to the previous menu.
5.8.8 Remote Operation
The menu functions as setting the continuous or discontinuous mode of remote
operation. Select System Settings –Remote Operation to enter the menu.
5.8.9 Network Settings
The network settings consist of CDMA switching and postback settings. CDMA
switching functions as enabling or disenabling CDMA switching. Select System
Settings –CDMA Switching to enter the menu. In the interface, a user can select
“Enabled” or “Disenabled”, the interface is shown as follows:
User Manual for iKeyMU-1_F Smart Key
38
The postback settings are only available in the case of the distribution network
key, including continuous mode and discontinuous mode.
5.9 Help
Operate the menu to check the system information of smart key, and press the Up or
Down key to select the various functional options on the menu, press the Enter key to
display the related information, as shown as follows:
Thereinto:
Press the Return key to directly return to the main menu.
User Manual for iKeyMU-1_F Smart Key
39
6 Special Functions
6.1 Auto Power-off
The smart key will automatically power off if continues its standby state for 6 minutes,
If it is being charged or fully-charged state, or being under cycle unlocking test for
electric-controlled lock or discharging test, the key will cancel the auto power-off, till the
above state is canceled.
6.2 Shortcut Menu
On the standby interface, press the shortcut key to show shortcut menu; under
order-operating mode, and it’s also available to press and hold the Enter key for three
seconds to show the shortcut menu as follows:
Press the Up or Down key to select options, then press the Enter key to set
corresponding parameters or operate.
6.3 Screensaver in Charging
Under charging mode, the smart key beeps and displays “Enabling Screensaver” to
automatically enter screensaver a minute later if no key is pressed or the key doesn’t
receive any operation order or self-learning data. The screen becomes black. Under this
mode, press any key or receive any operation order or self-learning data, the key will exit
the screensaver to enter the normal state.
User Manual for iKeyMU-1_F Smart Key
40
6.4 Outdoor/Indoor Mode
In outdoor operating, the key is exposed under sunlight and cause that users can’t
see the content on screen clearly, please switch to the outdoor display mode.
In the standby interface, press the Shortcut key to pop the shortcut menu as follows:
Press the Up / Down key to select the menu, select the “Outdoor” option, then press the
Enter key to enter the outdoor display mode as shown below:
Similarly, press the Shortcut menu under the outdoor mode, select the “Indoor” mode
to switch back to the indoor display mode. It is also available to enable the outdoor mode
as follows: hold down the On / Off key for 3 seconds after starting, the system can
automatically enable the outdoor display mode. After restart, the key can reset to the
default indoor mode.
Note: The battery runs out faster under the outdoor mode, thus it’s recommended to
use the system-default indoor mode in the case of a good visual effect.
User Manual for iKeyMU-1_F Smart Key
41
7 Precautions in Operating
Please note the following issues to ensure your safe and reliable use:
a. Placement: when the smart key is not in service, please place the smart key in a
fixed place, rather than random places.
b. Do not place the smart key in any specially wet environment in a long term, to
extend the service life of the smart key.
c. The smart key is product integrating machinery, optic, and electric technologies,
with a complex internal structure, except as authorized by its manufacturer, please do not
disassemble to avoid any damage to internal components.
d. Please keep its data transmission ports clean, to avoid any damage to data
transmission performance.
User Manual for iKeyMU-1_F Smart Key
42
8 Troubleshooting
Troubles Causes Solutions
The smart key cannot
self-learn, or is abnormal
in self-learning.
1. Battery voltage is low.
2. Self-learning program is
incorrectly operated.
3. Transmission port of the
main control equipment is
damaged.
1. Charge the smart key.
2. Operate the Self-learning program
correctly.
3. Renew the transmission port of the
main control equipment.
Mechanical coding lock is
opened, but unlocking
program cannot continue.
1. The internal IRDA
device of the smart key is
damaged.
2. Unlocking stem is offset.
1. Send the smart key back to Zhuhai
Unitech Power Technology Co., Ltd.
for repairing.
2. Re-adjust the horizontal position or
send it back to our company.
The smart key cannot
receive the operation
order sent from the
transmission port
1. The smart key has an
operation order that is
out of receiving state.
2. Internal IRDA device of
the smart key is damaged.
3. IR transmission cover is
blocked badly by dirt.
4. The transmission port of
main control equipment is
damaged.
1. Clear the smart key, and then insert
the transmission port to receive the
operation order.
2. Send the smart key back to Zhuhai
Unitech Power Technology Co., Ltd.
3. Sweep the dirt and clear the IR
transmission cover.
4. Renew the transmission port of
operation order.
The smart key shows
“Code correctly, please
unlock the mechanical
lock.” But the mechanical
coding lock still cannot be
opened.
1. The internal
components of the lock are
unsmooth.
2. The ring is blocked by
external components.
3. Battery voltage is low.
4. Internal unlocking
components of the smart
key do not work.
5. The mechanical coding
lock is damaged.
1. Renew the mechanical coding lock.
2. When unlocking, press the “Unlock”
key, and then pull the lock lightly
manually.
3. Ensure charge adequate power
before operating the smart key.
4. Send the smart key back to Zhuhai
Unitech Power Technology Co., Ltd.
5. Renew the mechanical coding lock.
When operating the
breaker, the breaker can
not be connected;
though the smart key
shows “Electric coding
lock can be opened.”
1. Internal relay of the
smart key is damaged.
2. The battery voltage is
low.
3. The smart key is in an
improper connection to the
electric coding lock.
1. Send the smart key back to Zhuhai
Unitech Power Technology Co., Ltd.
2. Ensure charge adequate power
before operating the smart key.
3. Clear the conductivity pole of the
electric coding lock, and renew the
electric coding lock if necessary.
User Manual for iKeyMU-1_F Smart Key
43
The smart key says “The
key has not self-learned,
not prepared for normal
operation.”
The smart key did not
self-learned before
operating normally.
Please self-learn.
Fully charged in a
charger, but the battery
runs out in a very short
time.
1. The charger is
damaged.
2. The battery has been
used for such a long time
that it causes the battery
aging.
3. The detection circuit for
power within the battery is
damaged.
1. Repair or renew the charger.
2. Renew the battery.
3. Send the smart key back to Zhuhai
Unitech Power Technology Co., Ltd.
Place the key into the
battery charger, the
interface says: “Low
power or battery failure,
please check”
1. The battery is installed
incorrectly.
2. Battery failure.
1. Reinstall the battery and set the
screws.
2. Renew the battery.
The battery cannot be
fully charged though it
has been charged for a
long time.
1. Rechargeable battery is
aged.
2. The smart key or the
charger exist failures.
1. Renew the battery.
2. Send the smart key or the charger
back to Zhuhai Unitech Power
Technology Co., Ltd.
9 Warning
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment .This equipment should be installed and operated with minimum
distance 20cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this
User Manual for iKeyMU-1_F Smart Key
44
device must accept any interference received, including interference that may cause
undesired operation.、
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.