ASSALOY YRHCPZB0 Yale Real Living Electronic Zigbee Lock User Manual 12 0001 Exhibit Cover

ASSA ABLOY Inc. Yale Real Living Electronic Zigbee Lock 12 0001 Exhibit Cover

Manual - YRT220-ZB

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: U4A-YRHCPZB0 IC: 6982A-YRHCPZB0 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 12-0001 Manufacturer: Assa Abloy Inc. Models: YRDZB, YRD210-ZB, YRD220-ZB, YRT210-ZB, YRT220-ZB Manual – YRT220-ZB
For Technical Assistance call Yale at 1-800-810-WIRE (9473)NOTE TO INSTALLERFAILURE TO FOLLOW THESE INSTRUCTIONSCOULD RESULT IN DAMAGE TO THE PRODUCTAND VOID THE FACTORY WARRANTYAn ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev AThis document is available on our website in printed Spanish and French. Go to www.yalerealliving.com. Click "Product Information & Documentation" and then "Installation Instructions".Este documento está disponible en español en nuestra página de internet. Vaya a www.yalerealliving.com. Presione "Información del Producto y Documentación" y luego "Instrucciones de Instalación".Ce document est disponible sur notre site Web dans le français imprimé. Allez à www.yalerealliving.com. Cliquez sur le "Information sur le produit et Documentation" et puis "Installation Instructions".Yale Real Living™ Touchscreen LeverInstallation and Programming Instructions
2An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev AWarnings .........................................................................................................................2Return Lock to Factory Default ................................................................................3Introduction .....................................................................................................................3InstallationComponents and Tools .............................................................................................4Prepare Lock for Installation ................................................................................. 5-6Install Lock .......................................................................................................... 6-11ProgrammingProgramming Features-Menus-Keys-Definitions ............................................. 12-13Operation .......................................................................................................... 14-16Miscellaneous InformationHardware Troubleshooting .....................................................................................17 Programming Troubleshooting ...............................................................................18Installing the Network Module ...............................................................................19Sample Pin Code Management Sheets ........................................................... 23-24TABLE OF CONTENTSWARNINGSFCC: FCC ID: U4A-YRHCPZW0 (Z-Wave); U4A-YRHCPZB0 (Zigbee)Model(s): YRT220-ZW, YRT220-ZBThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.IMPORTANT: The accuracy of the door preparation is critical for the proper functioning and security of this product. Misalignment can cause performance degradation and a lessening of security.Finish Care: This lockset is designed to provide the highest standard of product quality and perfor-mance. Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coat-ing and result in tarnishing.Warning: Changes or modifications to this device not expressly approved by Yale Security, Inc. could void the user's authority to operate the equipment.
3An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev A Factory Default SettingsTo reset the lock to factory default, see the following:The following procedure returns the lock to its factory defaults by deleting all user codes (including the Master PIN code*) and returning all programming features to their original default settings (see below). 1. Remove the batteries and then remove the inside escutcheon to access the reset button.2. The reset button (see image at right) is located above the PCB cable connector. 3. Hold down the reset button for a minimum of 3 seconds and then reinstall the batteries; once the batteries are properly installed, release the reset button. All features (including adjustable settings** (see below) should now be returned to factory default.Upon reset, Master Code Registration is the only option available and must be performed prior to any other programming of the lock.See "Operation" later in this manual for programming instructions. Reset Lock to Factory DefaultReset ButtonInside EscutcheonSettings Factory DefaultMaster Code Registration requiredAuto Re-lock EnabledOne Touch Re-Lock EnabledAudio EnabledAuto Re-lock Time **30 SecondsWrong Code Entry Limit **5 TimesShutdown Time **60 Seconds**Adjustable only when using Network Module
4An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev AINTRODUCTIONThe Yale Real Living™ Stand-alone Touchscreen Deadbolt Lock combines a robust lockset with a contemporary electronic aesthetic.Users benefit from an interactive touchscreen that makes day-to-day access effortless, as well as offering voice-guided programming for simple updates to user information in the event of staffing changes or security breaches. Yale Real Living™ is engineered for quick and easy installation and fits in place of a standard deadbolt lock door prep (ANSI/BHMA A156.115).If this is an RF-enabled network lock, it needs to be located within 50 - 100 feet of another network controller. That distance is influenced by objects between the lock and the controller and may be expanded depending on proximity to other RF network devices. Also, if the lock is connected to a network controller, it is recommended that it is programmed through the centralized user interface (PC or hand-held device) to ensure communication between the lock and the controller unit. Industry Canada:Canadian ID: 6982A-YRHCPZW0 (Z-Wave); 6982A-YRHCPZB0 (Zigbee)Model(s): YRT220-ZW, YRT220-ZBThis Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.For the U4A-YRHCPZB0 and 6982A-YRHCPZB0, the following statement applies:“This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.”Section 7.1.2 of RSS-GEN Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.En vertu des règlements d'Industrie Canada, cet émetteur radio ne peut fonctionner avec une antenne d'un type et un maximum (ou moins) approuvés pour gagner de l'émetteur par Industrie Canada. Pour réduire le risque d'interférence aux autres utilisateurs, le type d'antenne et son gain doivent être choisies de façon que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication réussie.Section 7.1.3 of RSS-GEN This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device.Cet appareil est conforme avec Industrie Canada RSS standard exemptes de licence(s). Son fonctionnement est soumis aux deux conditions suivantes: 1) ce dispositif ne peut causer des interférences, et 2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif.
5An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev ALock Installation #2 Phillips screw driver Allen wrench (3mm) - provided Parts Illustrations Tools NeededCOMPONENTS AND TOOLSINSTALLATION4 AA Alkaline BatteriesLatch boltStrikeDoor Prep 2-1/8" (54mm) hole saw 1" (26mm) boring bit 7/64" (2.5mm) drill bit Chisel & hammerBattery CoverNetwork Module (Optional)OutsideEscutcheonLatchKeys(4) Inside Escutcheon Mounting Screws (Pack 1)(2) Inside Mounting Plate Screws (Pack 1)(2) Latch & (2) Strike Plate Mounting Screws (Pack 2)CylinderInstallation InstructionsTemplateLatch BoltStrike Plate Included in the box. . .Inside Mounting Plate (with gasket)Inside EscutcheonOutside Escutcheon(2) Screw Packs (see below)KeysCylinderBattery CoverAllen Wrench4 AA Alkaline BatteriesAllen Wrench(2) Hex Set Screws (Pack 1)Inside EscutcheonOutside & Inside Lever HandlesInside Mounting Plate with Gasket (back of Inside Escutcheon)
6An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev AINSTALL LOCK Install LatchA. Remove the latch (Fig. 1) and strike plate from the packaging.NOTE: Latch ships with backset in 2-3/8" position (Fig. 1). Backset is the measurement from door edge to center of 2-1/8" diameter hole (see template supplied with lock).If required, pull to extend to 2-3/4" backset position (Detail 1A).NOTE: Different holes are used for (2) through bolts depending on backset (see Detail 1A).Figure 1Detail 1A2-3/8" through bolt posts2-3/4" through bolt postsThe lock is packed representative of how it will install on the door.Before installing the lock on the door:B. Install latch bolt in door. 1. Attach with two (2) M4 x 25.4mm screws supplied.C. Install strike on the door frame, using two (2) M4 x 25mm screws supplied, making sure to allow for the latch to be centered in the strike.NOTE: The latch bolt (and strike) can be installed in only one of two ways - with the bevel (slope) of latch facing out or facing in while standing outside of the door. If the door opens in, the bevel will face the outside; if the doors opens out, the bevel will face in. The strike plate is installed according to the orientation of the latch bolt. See Figures 1 & 2 for an example of a RH door that opens in.NOTE: Make sure door has been prepped according to specifications in template included with lock.(4) M4 x 25.4mmFlat HeadCombination ScrewsNOTE: Both latch face and strike plate have adhesive-backed covers to prevent marring and should be removed upon installation.Figure 2
7An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev AFigure 1AOutside Escutcheon (with gasket)Do not remove clip from Outside Escutcheon shank until correct handing has been determined and Outside Lever Handle is to be installed.(See page 9)ClipShankNOTE: RED marking indicates "top" of hub1. From outside of door, position the outside escutcheon by first routing the cable through 2-1/8" diameter hole and under the latch (Fig. 3A & B), then insert posts* and tailpiece into the latch. Square Drive Tube is marked (WHITE) to indicate "top" NOTE: The "tops" of both the square drive tube and the hub (in the shank) are marked to indicate their orientation for proper installation (Figures A & B).Shank NOTE: Cable goes under latch (Fig. 1A & 1B). Outside of DoorFigure 1BInside of Door "Top" of Drive Tube (marked WHITE)Tailpiece*Posts are inserted in holes according to backset adjustment. (Refer back to Detail 1A under "Install Lock") Install Outside EscutcheonFigure A Figure B
8An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev A 2. Remove the inside mounting plate (with gasket) from the back (door side) of the inside escutcheon (Fig. 2A).A. Ensure that gasket on inside mounting plate is properly fitted (Fig. 2B). Figure 2BFigure 2AInside Escutcheon & Mounting Plate (with gasket) 3. Remove the battery cover from the back of the inside escutcheon (Fig. 3) by loosening the captive Phillips head screw.Inside of Door5. Secure both assemblies by inserting (2) M4 x 25mm pan head machine screws through the mounting plate and into the slightly extended through posts of the outside escutcheon (Fig. 4B). Ensure that outside escutcheon is vertically aligned. Tighten securely with a #2 Phillips screwdriver. Do not over-tighten. 4. Holding the outside escutcheon flush to the door, position the inside mounting plate by routing the cable/connector through the mounting plate's 1/2" rectangular hole below center hole (Fig. 4A). Figure 4A6. Finish routing the cable and connector through the left upper slot, then behind center rib as shown in Fig. 4A.Figure 4BThrough posts hereScrewBattery Cover Install Outside EscutcheonFigure 3
9An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev A7. Attach cable assembly to the inside escutcheon printed circuit board (PCB) by lining up notches on top of cable connector to slots on PCB connector (Fig. 7A & 7B). Press connector in firmly using thumbs until completely seated (properly seated position indicated by arrows on PCB as in Fig. 7B). 8. Install and secure inside escutcheon to inside mounting plate using (4) M4 x 8mm [8-32 x 5/16"] pan head machine screws through the inside escutcheon into the mounting plate (Fig. 8). NOTE: Make sure cable does not obstruct path of the mounting screws.Inside EscutcheonReset ButtonFigure 7BFigure 7ACable ConnectorFigure 8
10An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev A Determine Lever HandingHinges on Right Hinges on Left RH RHR Lever LH LHR LeverRight handed lever positionLeft handed lever positionBefore proceeding with the next step, ensure correct lever handing for proper installation. Correct "curved" position Correct "curved" positionIncorrect Incorrect Determine Lever Position Both outside and inside lever handles should always point toward the door hinges.
11An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev AHex ScrewRH/RHR LH/LHRNOTE: For correct lever handing, the hex set screw for the outside lever shank must be installed as shown (Fig. 8B).Figure 8BFigure 1CA. Once correct handing is determined, remove the clip that has held the hub in its correct position by spreading clip ends to extract clip from shank as shown in Figure 1C with detail. Do not rotate cam from its original position. ("top" is marked RED)2. Remove clip from shank.3. Install hex set screw. Install the Exterior Lever (Right Hand shown)1. Install cylinder in exterior lever. (If necessary, remove key from cylinder)A. Drop cylinder in exterior lever handle as shown.90°B. Insert key in cylinder.A. Place set screw in hole on side of shank toward edge of door (opposite lever handle); turn CW to allow placement of lever handle over shank. Do not overtighten.CWFigure 1AFigure 1BTailpieceWhile supporting cylinder tailpiece (with finger); rotate key 90° clockwise (CW) to vertical position (Figure 1B).NOTE: RH shown; with LH lever, rotate key 90° counter-clockwise (CCW)
12An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev AEFigure 1EF. Secure lever handle by inserting allen wrench and rotating set screw CCW (Fig. 1F). Do not overtighten.G. Turn key 90° CCW; pull to remove key and test operation of lever handle, ensuring that the latch moves smoothly.G90°FFigure 1FCCWE. Push lever handle (with key & cylinder) over shank until hole on handle aligns with set screw in shank (Figure 1E).
13An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev A3. Turn set screw CCW to tighten and secure lever handle to shank.1. Insert four (4) AA alkaline batteries; the lock will flash and beep several times. 2. Install battery cover and tighten Phillips head screw.IMPORTANT: Before installing the batteries, test the mechanical operation of lock by rotating both the outside and inside lever handles. Also try using both the thumbturn and key. The movement of the latch should be smooth and unobstructed. If operation is not smooth, review the previous steps to ensure proper installation, while maintaining proper alignment of escutcheons.1. Rotate thumbturn counter-clockwise to horizontal position (Fig. 9A).2. Insert set screw on side of shank (toward edge of door); turn CW to allow placement of inside lever handle over shank.Figure 9AFigure 9B Figure 9C Install the Exterior Lever (Right Hand shown) Install Batteries
14An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev APROGRAMMINGPROGRAMMING FEATURES - MENUS - KEYS - DEFINITIONSProgramming Features-Menus-Keys-Definitions ............................................. 12-13Operation .......................................................................................................... 14-17Phillips ScrewNetwork Module SlotAlkaline Batteries4 AA TypeInside HandleStatus IndicatorBattery Cover Outside InsideSpeaker Hole Lockout ModeCylinderLow BatteryIndicatorNumbersTouch Screen " P " Key(Return to Previous) Menu and IconsTouch the screen with palm of hand or fingers to begin and end actions. Repeat operation using settings indicated.Enter Value 1 -10 (times or seconds). Click the indicated number. Enter Master PIN code* (4-8 digits in length). Advanced Mode only. Press the Star key on the touchscreen to Enter or Accept entry. Enter User PIN. Can be 4-8 digits in length.Press the Pound key on the touchscreen to enter Menu mode.User Serial Number (01 - 25); RF Controlled (01-250).Press this key to return to the previous step or menu setting. MU~*The Master Pin Code must be registered prior to any further programming of the lock.
15An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev A Low Battery Warning1 Lockout Mode2 Return to previous step3 Status IndicatorsLockout Mode: This feature is enabled by the Master code. When enabled, it restricts all user PIN code access. When attempting to enter a code while the unit is in Lockout, the Status Indicator flashes RED and BLUE; the keypad flashes as well.Low Battery: When battery power is low, the Status Indicator flashes RED. If battery power is completely lost, use the key override. Master PIN Code: The Master code is used for programming and for feature settings. NOTE: The Master Pin Code must be registered prior to programming the lock. The Master code will also operate the lock.Auto Re-lock Time: After successful code entry and the unit unlocks, it will automatically re-lock after a default of thirty (30) seconds. Re-lock time is adjustable from five (5) to thirty (30) seconds. One Touch Re-Lock: When the bolt is retracted, activating the keypad will extend the bolt (during Auto Re-Lock duration or when Auto Re-Lock is disabled). Shutdown Time: The unit will shutdown for a default of sixty (60) seconds and not allow operation after the wrong code entry limit has been met. When the unit is in Shutdown, the Status Indicator flashes RED and BLUE; the keypad flashes as well.Audio Mode: Choosing Disable (3) in Audio mode shuts off the code confirmation tone playback for use in quiet areas. Audio mode is enabled or disabled through feature programming by the Master code.Status LED: Located on inside escutcheon. User PIN Code: The User code operates the lock. Maximum number of user codes is 250 with Network Module; without Network Module, maximum is 25 user codes.Wrong Code Entry Limit: After a specified number of unsuccessful attempts at entering a valid PIN code the unit will shut down and not allow operation. Wrong code entry limit is adjustable from three (3) to ten (10) times through feature settings (up to 5 times with no RF network enabled - de-fault is 5; 10 with RF network enabled). Definitions Factory Default Settings*Adjustable with Network ModuleSettings Factory DefaultMaster Code Registration requiredAuto Re-lock EnabledOne Touch Re-Lock EnabledAudio EnabledAuto Re-lock Time **30 SecondsWrong Code Entry Limit **5 TimesShutdown Time **60 Seconds
16An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev AOPERATION1Press the key. Enter the new Master PIN code (4~8 digits), followed by the key. Lock ActivationThe touchscreen can be activated in several ways: Lock Operation Touch lock with back of hand or fingers to activate.Press the key to activate. Touch lock with fingers spread to activate.1. Touch the screen with the back of your hand or fingers to activate . 2. Press the key. Lock Response: “Register Master Code; press the key to continue.”3. Press the key. Lock Response: “Enter a 4 to 8 digit pin code followed by the pound key."4. Enter new 4-8 digit Master PIN code followed by the key.Lock visually confirms pin code selection, announces "Handing lock", the motor engages and the lock responds, "Completed". Master Code Set**This step is required prior to programming of the lock.
17An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev AUser PIN Codes can only be programmed through the Master PIN Code*.1. Touch the screen with the back of your hand or fingers to activate . 2. Enter the 4-8 digit Master PIN code followed by the key. Lock Response: “Menu mode, enter number, press the key to continue.”3. Enter “2” followed by the key. 4. Enter “1” followed by the key. 5. Enter the User Number to be registered (1-25) followed by the key. 6. Enter a 4-8 digit PIN code for the User number followed by the key. 7. To continue adding users press the key.8. Press the key to complete the process and conclude the programming session. Set Up User PIN CodesNote: When registering User codes, the code must be entered within 20 seconds or time expires, Lock Response: “Time expired”, no codes are registered and the process must be re-started. 3Press the key to confirm the selection. Enter PIN code. 2 1Touch lock with back of hand or fingers to activate. PIN code structureMaximum number of user codes is 250 with Network Module; without Network Module, maximum is 25 user codes. Open Door with PIN Code*Master PIN code must be registered before User codes can be added.
18An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev AMaster PIN Code SettingMM User PIN Code Registration RegisterDeleteAdvanced Lock SettingsVolume Setting Language Setting mode Lockout Mode**Network Module Setting RegisterHighEnglishEnableDisableDeleteSilentSpanishFrenchLowUser Number (UN) 1~25: without network module 1~250: with network module 1 2 3UContinue CompleteContinue Complete**This function appears only with RF network module installed.Auto Re-lock Setting Enable Disable Inside Escutcheon LEDOne Touch Locking Setting Enable Disable Feature Programming Through Menu Mode Using Master PIN code* 1. Touch the screen with the back of your hand or fingers to activate . 2. Enter the 4-8 digit Master PIN code* followed by the key. Lock Response: “Menu mode, enter number, press the key to continue.”3. Enter digit corresponding to the function to be performed followed by the key. Follow the voice commands.Note: If the lock is connected to a network controller, it is recommended that it is programmed through the central-ized user interface (PC or hand-held device) to ensure communication between the lock and the controller unit. *The Master PIN code must be registered prior to any other programming of the lock.Enable Disable
19An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev AMISCELLANEOUSCycle the lock in both the locked and the unlocked positions. If problems are found: TROUBLESHOOTING Hardware TroubleshootingSymptom Suggested ActionDoor is binding a. Check that door and frame are properly aligned and door is free swinging.b. Check hinges: They should not be loose or have excessive wear on knuckles. Latch will not deadlock a. Check for sufficient clearance of the latch within the strike-side jamb. Correct this by increasing the depth of the pocket for the latch.b. Check for misalignment of latch and/or strike which may be preventing latch from properly entering the strike. With the door open, extend and retract the latch; if it is smooth, check the strike alignment. Latch does not extend or retract smoothly a. Latch and strike are misaligned, see above.b. Check the backset of door relative to adjustments already made to latch.c. Verify proper door preparation and re-bore holes that are too small or misaligned.d. Verify keypad cable/connector is routed under the latch (see Fig. A).e. Verify latch is installed with correct side up (Fig. A).Inside of DoorFigure AHardware Troubleshooting ......................................................................................17 Programming Troubleshooting ...............................................................................18Installing the Network Module ...............................................................................19Change Lever Handing .................................................................................... 20-21 Replace/Install Cylinder .........................................................................................22Sample Pin Code Management Sheets ........................................................... 23-24
20An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev ASymptom Suggested ActionLock does not respond – door is open and accessible.The touchscreen will become active when pressed with the back of hand or fingers in at least 3 areas simultaneously. Use a larger area of the hand or fingers and verify contact with at least 3 areas.If touchscreen numbers are visible, check to see if they respond when pressed.Check batteries are installed and oriented correctly in the battery case.Check batteries are in good condition; replace batteries* if discharged.Check to see if touchscreen cable is fully connected and not pinched.Lock does not respond – door is locked and inaccessible. Mechanical key will grant access.Batteries may be completely discharged.Use mechanical key to gain entry and replace batteries*.The unit is on for a while, and then shows no reaction. Lights dim.The batteries do not have enough power. Replace the batteries*.Unit chimes to indicate code acceptance, but the door will not open.Check to see if there is an existing lock device on the door.Check the door gaps for any foreign objects between door and frame.Check that the cable is firmly connected to the PCB.Unit operates to allow access, but will not automatically re-lock. Check to see if Passage Mode** is enabled (Network module units only). If the Passage Mode icon on the touchscreen and the status indicator on the interior escutcheon flicker for several seconds, it is set at Passage Mode.Disable Passage Mode to lock the door.If low battery indicator is lit, replace batteries*.PIN codes will not register. PIN codes must consist of 4 to 8 digits to register.The same PIN code cannot be used for multiple users. Registration/management of PIN codes is set by the authority of Master Code. The Master PIN code must be registered prior to adding any users.Contact the Master user.User codes must be entered within 20 seconds (while the touchscreen is active) or the process will have to be restarted.The star (*) or pound (#) can not be used as part of the PIN code.Upon entering a PIN code and pressing the star (*) key, the unit displays an “invalid code” error or the lock times out without responding.Lockout Mode is enabled.Only the Master Code can enable Lockout Mode.Contact the Master user.Upon entering a PIN code and pressing the (*) key, the red padlock icon appears and there are different tones.Check to see if lock is set** at Lockout Mode.Setting/managing Lockout Mode is done through Master Code only. Contact the Master user.The unit operates, but it makes no sound.Check to see if Silent Mode is enabled (pages 8, 11).The unit responds “Low Battery” This is the voice alarm alerting that it is time to replace the batteries. Replace all four (4) batteries with new AA Alkaline batteries*.Upon entering a PIN code and pressing the star (*) key, the unit responds “Wrong number of digits.”The digits entered were incorrect or incomplete. Re-enter the correct code. Programming Troubleshooting* When batteries are replaced, Network Module locks have a real time clock that will be set through the User Interface; it is recommended to verify correct date and time particularly those locks operating under Daylight Saving Time (DST).** Network module units only
21An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev AIMPORTANT: The batteries must be removed prior to removing and/or inserting the network module:• Remove batteries• Remove and/or insert network module• Reinstall batteries Installing the Network ModuleUse Feature Programming step 7 (page 16) for enrollment of the Network Module.
22An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev A How to Change Handing of Lever (Reverse Levers)1. Remove the outside lever handle:A. Insert key in cylinder (outside lever handle); rotate key 90° clockwise. B. Insert allen wrench (included) in set screw on side of lever (toward edge of door); turn clockwise to loosen.C. Pull to remove lever handle/key/cylinder. BCCWFC90°A90°
23An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev A2. Remove the inside lever handle:A. Insert allen wrench (included) in set screw on side of lever (towards edge of door); turn clockwise to loosen lever handle.B. Pull to remove lever handle. AA. Remove and switch handles (inside to outside, outside to inside).B. Remove cylinder from outside lever handle.C. Insert cylinder in "new" outside lever (Fig. 3A).D. Push handle in allowing holes for set screw to align.E. Insert set screw and tighten by turning set screw counter-clockwise.3. Change the lever handing:IncorrectNOTE: "Swoop" of lever handle must be oriented in upward direction as shown in Fig. 3ACorrectFigure 3ABFigure 3B
24An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev A1. Remove cylinder:A. Repeat previous steps for removing the outside lever handle.B. Remove cylinder. How to Replace or Install Cylinder2. Install new cylinder: A. Insert cylinder in "new" outside lever. B. Push handle in allowing holes for set screw to align. C. Insert set screw and tighten by turning set screw counter-clockwise. D. Verify that new cylinder fits and rotates freely. E. Test operation of the new cylinder/key.`
25An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev APIN CODE MANAGEMENT SAMPLE SHEETSPIN Code Management (No Network Module - Up to 25 Users)Location: Door Number: User User Name User # PIN CodeUser Type User Name User # PIN CodeMaster User 13User 01 User 14User 02 User 15User 03 User 16User 04 User 17User 05 User 18User 06 User 19User 07 User 20User 08 User 21User 09 User 22User 10 User 23User 11 User 24User 12 User 25
26An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev APIN Code Management (With Network Module - Up to 250 Users) - Duplicate Sheet to record entriesUser Type User Name User # PIN Code User User Name User # PIN CodeMaster User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___
ONLINE LITERATURE AND TEMPLATESFor the latest information on Yale products visit our website at www.yalelocks.com. Click on the “Literature” button to find the most up-to-date catalogs, parts manuals, templates, specifica-tions and installation instructions.Yale Locks & Hardware100 Yale Avenue, Lenoir City, TN 37771 • Product Support Tel 800.810.WIRE (9473) • www.yalelocks.comYale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company. Yale® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Yale Real Living™ is a trademark of Copyright © 2012, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without express written permission of Yale Security Inc., an ASSA ABLOY Group company is prohibited.YALE, with its unique global reach and range of products, is the world’s favorite lock — the preferred solution for securing your home, family and personal belongings.ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience.An ASSA ABLOY Group brandP/N AYRT-220-INST-FUL Rev A

Navigation menu