ATEQ ATEQ-VTXX intelligent tire pressure Analyzer User Manual Meeting Review

Download:
Mirror Download [FCC.gov]
Document ID	661380
Application ID	7lOuPNyredmzS4DhEFNXoQ==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	48.75kB (609329 bits)
Date Submitted	2006-05-24 00:00:00
Date Available	2006-05-24 00:00:00
Creation Date	2006-04-19 16:40:27
Producing Software	OpenOffice.org 2.0
Document Lastmod	2006-04-19 12:49:54
Document Title	Meeting Review
Document Creator	Writer
Document Author:	Mike Crimmings

User’s manual
TPM-RKE Analyzer
9936
Version 06.03 Daimler Chrysler
Reference: QS-258DCA-U
User guide
REGULATORY STATEMENTS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions;
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
“Changes or modifications not expressly approved by the manufacture could void the
user's authority to operate the equipment.”
“NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications not expressly approved by the manufacturer may
violate the user's authority to operate the equipment.
Industries Canada:
The installer of this radio equipment must ensure that the antenna is located or pointed
such that it does not emit RF field in excess of Health Canada limits for the general
population; consult Safety Code 6, obtainable from Health Canada’s website
www.hc-sc.gc.ca/rpb"
User’s Manual
TABLE OF CONTENTS
User guide
TPM-RKE ANALYZER 9936............................................................................................. 2
.1 DESCRIPTION OF THE TPM-RKE ANALYZER 9936........................................................................ 2
.2 FEATURES.......................................................................................................................................... 3
..1 Radio frequencies........................................................................................................................... 3
..2 Type of valve.................................................................................................................................. 3
.3 CONNECTORS.................................................................................................................................... 4
..1 Supply connector............................................................................................................................ 4
..2 USB connector............................................................................................................................... 4
..3 RS232 connector............................................................................................................................ 4
.4 DESCRIPTION OF THE INSTRUMENT............................................................................................... 5
..1 Power on/off key............................................................................................................................. 5
.5 FRONT PANEL DESCRIPTION........................................................................................................... 6
..1 Display............................................................................................................................................ 6
..2 Lights.............................................................................................................................................. 6
..3 Keys................................................................................................................................................ 6
.6 BATTERY SUPPLY............................................................................................................................. 7
..1 Battery status.................................................................................................................................. 7
.7 MEASUREMENT.................................................................................................................................. 8
..1 Key measurement (RKE test)......................................................................................................... 8
..2 Valve measurement (TPM functions).............................................................................................. 9
.8 SETTINGS............................................................................................................................................ 12
..1 Parameters menu........................................................................................................................... 12
.9 STARSCAN.......................................................................................................................................... 16
..1 Data transfer................................................................................................................................... 16
..2 TPM/RKE Analyzer program up-dating........................................................................................... 16
.10 MENU STRUCTURE.......................................................................................................................... 17
..1 Main menu...................................................................................................................................... 17
.11 CORRESPONDANCES TABLES...................................................................................................... 19
..1 Vehicle / Body / valve..................................................................................................................... 19
..2 Countries / frequencies................................................................................................................... 19
................................................................................................................................................................ 19
Index
20
User guide TPM-RKE Analyzer Page 1/20
User guide
TPM-RKE ANALYZER 9936
.1
DESCRIPTION OF THE TPM-RKE ANALYZER 9936
The principal of this instrument is to awaken and then retrieve data from smart
valves mounted on vehicle wheels in order to verify their identifiers.
The instrument interacts with the smart valves without contact through wireless
communication.
LCD
Display
Light
Indicators
Keypad
RS232 (RJ45)
Connecter
USB
Connecter
User guide TPM-RKE Analyzer Page 2/20
.2
FEATURES
..1
RADIO FREQUENCIES
Awakening transmission frequency: 125 kHz (LF).
Reception frequencies: 433 MHz or 315 MHz (RF).
..2
TYPE OF VALVE
This instrument is especially designed for the measurement of the Siemens and
Schrader valves installed into Daimler-Chrysler vehicles.
Siemens
Siemens
Schrader
User guide TPM-RKE Analyzer Page 3/20
.3
CONNECTORS
..1
SUPPLY CONNECTOR
To supply the instrument and recharging the internal battery.
The voltage of the charger is a 24 V DC.
..2
USB CONNECTOR
The USB connector allows the instrument software programs to
be updated.
StarScan tool can retrieve information through the USB
connector.
..3
RS232 CONNECTOR
Not used.
User guide TPM-RKE Analyzer Page 4/20
.4
DESCRIPTION OF THE INSTRUMENT
..1
POWER ON/OFF KEY
KEY
FUNCTION
Power on: Press this key to power on the instrument.
Power off: Press and hold the key (more than 3
seconds) to power off the instrument.
..1. Power on
At power on, it displays the logo.
Then it displays the software revision number.
Then the tool displays the main menu and the operator
can select desired function.
ATEQ VT 60
Version 06.03
MAIN MENU
> RKE TEST
TPM FUNCTIONS
SETTINGS
User guide TPM-RKE Analyzer Page 5/20
.5
FRONT PANEL DESCRIPTION
..1
DISPLAY
The LCD screen displays the parameters menus and
the measurements results.
..2
LOW BAT
MAIN MENU
> RKE TEST
TPM FUNCTIONS
SETTINGS
LIGHTS
Battery level light: When this light is on, the battery level is too low, charge it.
Pass test light: When this light is on, the instrument has correctly
received the frame from the valve (or the RKE).
PASS
Fail test light: When this light is on, the instrument has not received the
frame from the valve (or the RKE).
FAIL
Transmission light: When this light is flashing, the instrument is
currently transmitting a 125 KHz frequency to activate a valve.
TX
CHARGE
Battery charging light: This light turns on when the instrument is being
charged.
..3
KEYS
Power on and off the instrument.
Navigation menu, "up".
Navigation menu, "down".
Select Key, press to enter in the chosen function or validate a parameter.
Cancel key, return to the previous menu or function without parameter validation.
Test Key, to initiate a test cycle.
User guide TPM-RKE Analyzer Page 6/20
.6
BATTERY SUPPLY
The instrument uses a Li-ion battery, the autonomy depends of the number of
cycles carried out. It battery must be recharged with a 24 V DC external power
supply (Included).
..1
BATTERY STATUS
When the battery is too low, the "LOW BATT" light is
flashing for 2 seconds and the instrument will
powered off.
LOW BATT
PASS
FAIL
To see the battery status, select the "SETTINGS"
menu using the
and
keys.
Validate your entry with the
By using the
and
key.
keys, select the
"BATTERY LEVEL" menu and validate with the
MAIN MENU
RKE TEST
TPM FUNCTIONS
> SETTINGS
PARAMETERS MENU
UNIT : METRIC
AUTO OFF: DISABLE
> BATTERY LEVEL
key.
The instrument displays the receivers and the battery
status.
Press the
button to return to the main menu.
RECEIVER
1: READY
2: READY
BATTERY
MAIN MENU
> RKE TEST
TPM FUNCTIONS
SETTINGS
User guide TPM-RKE Analyzer Page 7/20
TX
.7
MEASUREMENT
..1
KEY MEASUREMENT (RKE TEST)
This menu allows putting the instrument in key test
mode (RKE).
Select this mode with the
key,
the instrument invites you to launch the test by
pressing the
key.
Wait a second for the initialization if the instrument.
The instrument displays a horizontal bar and invites
you to test the key fob. Hold the key fob near the
antenna of the instrument (between 7 and 15
centimetres) and press any button of the key fob.
The intensity of the RF signal force is indicated on the
scale of the horizontal bar. The greater the key fob RF
signal power, the greater the horizontal bar is filled.
Press the
button to return to the main menu.
MAIN MENU
> RKE TEST
TPM FUNCTIONS
SETTINGS
EUROPE
RKE TEST
< TEST > TO START
EUROPE
1997/E
RF LEVEL
PLEASE WAIT...
EUROPE
RKE TEST
PRESS KEY FOB BUTTON
EUROPE
RKE TEST
PRESS KEY FOB BUTTON
MAIN MENU
> RKE TEST
TPM FUNCTIONS
SETTINGS
User guide TPM-RKE Analyzer Page 8/20
..2
VALVE MEASUREMENT (TPM FUNCTIONS)
Use the following directions to test the functionality of a TPM sensor:
Select "TPM FUNCTION" by using the
keys and validate using the
By using the
and
and
key.
keys, select the model
year of the valve to be tested and validate using the
key (existing years from 1997 to 2006).
MAIN MENU
RKE TEST
> TPM FUNCTIONS
SETTINGS
MODEL YEAR SELECTION
> 1997
1998
1999
MODEL YEAR SELECTION
2004
2005
> 2006 ...
BODY STYLE SELECTION
Next, by using the
and
keys, select the
body code of the valve to be tested and validate with
the
key (this code is in correspondence with a
vehicle).
Next, by using the
and
keys, select the
key (you
trigger selection and validate using the
may select the mode you want to trigger on the valve,
read, park, deactivation and sniffing).
Then the instrument is displaying the valve
characteristics chosen and waiting for a start cycle. To
start cycle, press the
key.
> CS
HB
KJ
LX
RS
> WK
BODY STYLE SELECTION
TRIGGER SELECTION
> READ SENSOR
PARK SENSOR
DEACTIVATE SENSOR
EUROPE
2006 .../WK
PARK SENSOR
< TEST > TO START
User guide TPM-RKE Analyzer Page 9/20
LOW BATT
PASS
When the "TX" light is flashing, it indicates that the
instrument is emitting a frame wirelessly to make the
valve respond.
First case: a valve is detected:
When the instrument has detected a frame from the
valve, the "PASS" light is on and it displays the valve
characteristics.
To locate the valve on the car, press the
key.
Then select the valve wheel location and press the
key.
The instrument confirms the location of the valve.
And indicates the location valve on the car.
TX
EUROPE
2006 .../WK
PARK SENSOR
TRIGGER PROCESSING
LOW BATT
NB: the identifier displayed on the screen must be the
same as the one written on the valve.
FAIL
PASS
FAIL
TX
SENSOR DATAS
80AA323B
240 KPa
SLEEP MODE
TIRE LOCATION
80AA323B
SENSOR DATAS
240 KPa
SLEEP MODE
TIRE LOCATION
TIRE LOCATION
> LEFT FRONT : EMPTY
LEFT REAR1 : EMPTY
LEFT REAR2 : EMPTY
LEFT FRONT : STORED
TIRE LOCATION
> LEFT FRONT : OK
LEFT REAR1 : EMPTY
LEFT REAR2 : EMPTY
Second case: no valve is detected:
After a few moments, if no valve frame is detected, the
"FAIL" light is on, so start a new test.
LOW BATT
PASS
FAIL
User guide TPM-RKE Analyzer Page 10/20
TX
MAIN MENU
Press the
> RKE TEST
TPM FUNCTIONS
SETTINGS
button to return to the main menu.
..1. Results explanation
The picture below is an example of a valve data communication result:
Tire internal
pressure at
sea level
Valve
identifier
80AA323B
SENSOR DATAS
240 KPa
SLEEP MODE
TIRE LOCATION
Valve
mode
To locate the
valve on the car
..2. No valve response
If the instrument doesn't receive any information from the valve or if the valve is
not compatible with the parameters, after 36 seconds a time out on the
instrument stops its cycle and the "FAIL" light is switched on.
LOW BATT
PASS
FAIL
TX
User guide TPM-RKE Analyzer Page 11/20
.8
SETTINGS
..1
PARAMETERS MENU
This menu will allow the instrument to be configured according to the operator
preferences.
..1. Country
The parameter "COUNTRY" allows the user to select the geographic valves
region.
Select "SETTINGS" by using the
and
keys and validate with the
key.
Select the "COUNTRY" parameter and validate with
the
key.
Then select the valve region between US/CAN/MEX,
JAPAN, MIDDLE EAST, EUROPE and OTHER.
NB: the TPM function is not available for the Japan
country.
MAIN MENU
RKE TEST
TPM FUNCTIONS
> SETTINGS
PARAMETERS MENU
> COUNTRY : EUROPE
UNIT : METRIC
AUTO OFF: DISABLE
REGION SELECTION
> US/CAN/MEX
JAPAN
MIDDLE EAST
MAIN MENU
Press the
button to return to the main menu.
> RKE TEST
TPM FUNCTIONS
SETTINGS
User guide TPM-RKE Analyzer Page 12/20
..2. Unit
The parameter "UNIT" allows the user to choose between the "METRIC" unit and
the "US" unit.
Select "SETTINGS" by using the
and
keys and validate with the
key.
Select the "UNIT" parameter and validate with the
key.
Then select the unit between "US" and "METRIC" and
validate with the
Press the
key.
button to return to the main menu.
MAIN MENU
RKE TEST
TPM FUNCTIONS
> SETTINGS
PARAMETERS MENU
COUNTRY : EUROPE
> UNIT : METRIC
AUTO OFF: DISABLE
UNIT SELECTION
US
> METRIC
MAIN MENU
> RKE TEST
TPM FUNCTIONS
SETTINGS
User guide TPM-RKE Analyzer Page 13/20
..3. Auto off
The "AUTO OFF" setting allows the user to turn off the instrument automatically
after a certain time without use. This is to save the battery before a recharge is
required.
Select "SETTINGS" by using the
and
keys and validate with the
key.
Select the "AUTO OFF" parameter and validate with
key.
the
MAIN MENU
RKE TEST
TPM FUNCTIONS
> SETTINGS
PARAMETERS MENU
COUNTRY : EUROPE
UNIT : METRIC
> AUTO OFF: DISABLE
The cursor position moves to the right of the screen
and by using the
and
keys, choose the
auto off time between "DISABLE" and 1 to 60 minutes,
then validate with the
PARAMETERS MENU
COUNTRY : EUROPE
UNIT : METRIC
AUTO OFF: 5 mn <
key.
MAIN MENU
Press the
button to return to the main menu.
> RKE TEST
TPM FUNCTIONS
SETTINGS
In the above example, after 5 minutes with no use, the instrument will switch off
automatically.
User guide TPM-RKE Analyzer Page 14/20
..4. Back light
The "BACK LIGHT" menu allows the user to adjust the light intensity of the
display. The back light increases the battery consumption.
Select "SETTINGS" by using the
and
keys and validate with the
key.
Select the "BACK LIGHT" parameter and validate with
key.
the
MAIN MENU
RKE TEST
TPM FUNCTIONS
> SETTINGS
PARAMETERS MENU
AUTO OFF: DISABLE
BATTERY LEVEL
> BACK LIGHT: 0 %
The cursor position moves to the right of the screen
and by using the
and
keys, adjust the
back light intensity, choose between 1 to 100 percent
PARAMETERS MENU
COUNTRY : EUROPE
UNIT : METRIC
AUTO OFF: 5 mn <
by 1 percent increments, then validate with the
key.
MAIN MENU
Press the
button to return to the main menu.
> RKE TEST
TPM FUNCTIONS
SETTINGS
User guide TPM-RKE Analyzer Page 15/20
.9
STARSCAN
..1
DATA TRANSFER
Data transfer from the TPM/RKE Analyzer 9936 instrument to the StarScan tool.
Connect the USB cable from the TPM/RKE Analyzer 9936 instrument to the
StarScan tool, then the StarScan tool recognizes the information to download
automatically.
..2
TPM/RKE ANALYZER PROGRAM UP-DATING
Connect the USB cable between the computer and the instrument, the USB
drivers must be installed first.
Press and hold the
and the
at the same
BOOTSTRAP VT60 4.11
USB.2.00
time.
NB: in case of error of manipulation, to exit from this
menu, press the
key.
When the USB cable is connected, "CONFIGURED"
appears on the screen.
On the computer open the attached file and a browser
will appear. Click on "LOAD".
The loading progress is displayed and when
completed, the instrument will boot to the main menu.
Now it's possible to disconnect the USB cable from the
PC and the instrument.
BOOTSTRAP VT60 4.11
USB.2.00 CONFIGURED
MAIN MENU
> RKE TEST
TPM FUNCTIONS
SETTINGS
User guide TPM-RKE Analyzer Page 16/20
.10 MENU STRUCTURE
..1
MAIN MENU
MAIN MENU
RKE TEST
Sub menu 1
RKE TEST
Press  to
start
1997 > 1998 >
1999 > 2000
Sub menu 2
Sub menu 3
PR
READ SENSOR
Sub menu 4
TPM FUNCTIONS
DEACTIVATE
SENSOR
SNIFFING MODE
2001
DEACTIVATE
SENSOR
SNIFFING MODE
2002
DEACTIVATE
SENSOR
SNIFFING MODE
2003
DEACTIVATE
SENSOR
SNIFFING MODE
2004
LH > PR > WJ
READ SENSOR
TIRE LOCATION:
Left / right /
front / rear…
TIRE LOCATION:
Left / right /
front / rear…
TIRE LOCATION:
Left / right /
front / rear…
TIRE LOCATION:
Left / right /
front / rear…
TIRE LOCATION:
Left / right /
front / rear…
TIRE LOCATION:
Left / right /
front / rear…
TIRE LOCATION:
Left / right /
front / rear…
TIRE LOCATION:
Left / right /
front / rear…
TIRE LOCATION:
Left / right /
front / rear…
LH > PR > RS >
WJ
READ SENSOR
CS > LH > RS >
W J > ZB
READ SENSOR
CS > KJ > LH >
RS > WJ > ZB
READ SENSOR
User guide TPM-RKE Analyzer Page 17/20
V
DEACTIVATE
SENSOR
SNIFFING MODE
2005
PARK SENSOR
DEACTIVATE
SENSOR
SNIFFING MODE
2006
CS > KJ > RS >
WK > ZB
CS > HB > KJ >
RS > WK > XK
READ SENSOR
READ SENSOR
PARK SENSOR
DEACTIVATE
SENSOR
SNIFFING MODE
TIRE LOCATION:
Left / right /
front / rear…
TIRE LOCATION:
Left / right /
front / rear…
TIRE LOCATION:
Left / right /
front / rear…
TIRE LOCATION:
Left / right /
front / rear…
TIRE LOCATION:
Left / right /
front / rear…
SETTINGS
COUNTRY
US/CAN/MEX
JAPAN
MIDDLE EAST
EUROPE
OTHER
UNIT
US
METRIC
AUTO OFF
DISABLE > 1 to
60 min
0 to 100 %
BATTERY LEVEL
BACK LIGHT
User guide TPM-RKE Analyzer Page 18/20
.11 CORRESPONDANCES TABLES
..1
VEHICLE / BODY / VALVE
Body
code
Model year
Valve
manufacturer
Prowler
PR
1997-2002
Schrader
Viper
ZB
2003 - Present
Schrader
Intrepid/300M
LH
2001 - 2004
Schrader
Grand Cherokee
WJ
2001 - 2004
Schrader
Pacifica
CS
2003.5 - 2004
Schrader
Town & Country/Caravan
RS
2002 - 2003
Schrader
Town & Country/Caravan
RS
2004 - 2005
Siemens
Liberty
KJ
2004
Siemens
Liberty
KJ
2005 - Present
Commander
XK
2006 - Present
Siemens
Siemens
Pacifica
CS
2005 - Present
Siemens
Town & Country/Caravan
RS
2006 - Present
Siemens
Grand Cherokee
WK
2005 - Present
Siemens
300C/Magnum/Charger
LX
2006 - Present
Siemens
Durango
HB
2006 - Present
Siemens
Vehicle line
..2
COUNTRIES / FREQUENCIES
Country
TPM frequencies (MHz)
RKE frequencies (MHz)
315
315
315
Middle east
315
433
Europe
433
433
Other
315
315
US / Canada / Mexico
Japan
User guide TPM-RKE Analyzer Page 19/20
Index
Auto off................................................................................................................ 14
Back light............................................................................................................. 15
Battery status......................................................................................................... 7
Connectors............................................................................................................ 4
Country................................................................................................................ 12
Description............................................................................................................. 2
Display................................................................................................................... 6
Key fob.................................................................................................................. 8
Keys...................................................................................................................... 6
Lights indicator...................................................................................................... 6
Measurement......................................................................................................... 9
Measurements....................................................................................................... 8
Menu structure..................................................................................................... 17
No response........................................................................................................ 11
Parameters menu................................................................................................ 12
Parameters setting.............................................................................................. 12
Power on............................................................................................................... 5
Radio frequencies.................................................................................................. 3
RKE....................................................................................................................... 8
RS232 connectors................................................................................................. 4
StarScan tool....................................................................................................... 16
Start key................................................................................................................ 5
Supply.................................................................................................................... 7
Supply connector................................................................................................... 4
Tables.................................................................................................................. 19
TPM....................................................................................................................... 9
Unit...................................................................................................................... 13
Up-dating............................................................................................................. 16
USB connectors..................................................................................................... 4
Valves types.......................................................................................................... 3
Results explanation............................................................................................ 11
User guide TPM-RKE Analyzer Page 20/20
Source Exif Data: File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 22
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:d390a04c-a609-48c3-b531-a7366028d8ec
Producer                        : OpenOffice.org 2.0
Create Date                     : 2006:04:19 16:40:27+02:00
Creator Tool                    : Writer
Modify Date                     : 2006:04:19 12:49:54-04:00
Metadata Date                   : 2006:04:19 12:49:54-04:00
Document ID                     : uuid:b5dc4fa8-ec3e-42bb-a2cf-b35f8fbe66ab
Format                          : application/pdf
Title                           : Meeting Review
Creator                         : Mike Crimmings
Author                          : Mike Crimmings

EXIF Metadata provided by EXIF.tools
FCC ID Filing: TJB-ATEQ-VTXX

								
							
		
		
			Navigation menu

			
									
                                                 
                                                
Upload a User Manual

					
									
										
						Namespaces
						
															Wiki Guide
															

															HTML
                                                                                                                        PDF
 

                                                                                                                       Info
													
					
									
				
										
						Views
						
															User Manual
															Discussion / Help
													
					


									

			
			
				
						
			Navigation

		
			


		
				
		
		
							
											© 2025 UserManual.wiki | Privacy Policy
									
							
											Contact Us
											DMCA