Ademco 8DL6150RFT3 Security Keypad Transceiver User Manual

Honeywell International Inc. Security Keypad Transceiver Users Manual

a href="https://usermanual.wiki/Ademco" itemprop="url"> Ademco >

Users Manual

K4460-1V6 2/06 Rev C ADEMCO 6150RFADEMCO 6150RFADEMCO 6150RFADEMCO 6150RF Keypad/TransceiverKeypad/TransceiverKeypad/TransceiverKeypad/Transceiver INSTALLATION AND SETUP GUIDE GENERAL INFORMATION The 6150RF Keypad/Transceiver is a combination unit incorporating a normally-open relay output and the functions of: • 6150 Fixed Addressable Keypad • 5881M RF Receiver • 5800TM Transmitter Module The 6150RF Keypad/Transceiver may be used on any control panel that supports the 6150 Keypad. Wireless Features The 6150RF supports the following: • 5828/5828V wireless keypads. • Up to eight wireless keys locally (programmed directly into 6150RF) without occupying any zones supported by the control panel. • Button-type transmitters (e.g., 5804, 5804BD) for local operation. • A maximum of 16 transmitters programmed into any 5800 Series-supported control panel. • Wireless keys with high-security (e.g., 5804E). • RF jam detection when the receiver is enabled. • Low-battery indications for the local wireless keys. • A nominal range of 200' for the RF transmitters (some transmitters have a shorter range). • Wireless keys for control panels that do not support RF themselves (such as 4110DL). • Sends status signals (Armed, Ready, etc.) to bi-directional units such as 5804BDV and 5828/5828V. UUUULLLL The 5802, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5804E, 5814, 5816TEMP, 5819, 5819BRS, 5819WHS, 5828/5828V and 5850 transmitters are not intended for UL installations. Programming Features • Auto Enroll mode for programming wireless keys. • Provides a method for deleting a serial number and re-enrolling a new one in its place. • Provides default settings for the wireless key functions. Additional Features • Operates the on-board relay in conjunction with the receiver (e.g., to trip a garage door opener). UUUULLLL This feature is not intended for UL installations. • Activates relays programmed into the control panel. • Provides an End User mode to enable/disable local wireless keys (e.g., if a user accidentally loses a wireless key). Refer to the 6150RF User Guide for this procedure.INSTALLING THE 6150RF Locate the 6150RF in an area and at a height where it is convenient for user operation. The 6150RF must be at least 10 feet from the control panel to ensure proper operation of the RF receiver. Perform the following steps to install the 6150RF. 1. Push the two case release snaps at the bottom of the keypad with the blade of a medium screwdriver (this will push in the release snap), then pull that side of the case back away. Insert the screwdriver in the side of the keypad (between the front and back case) and gently twist to release the side locking tab. Repeat for the other side. Refer to Figure 1 for location of the case back release snaps and locking tabs. 2. Route the wiring from the control panel through the opening in the case back. (See the control panel’s instructions for proper wire run lengths.) 3. Mount the case back directly to a wall or electrical gang box. 4. Connect the power and data wires from the control panel to the terminals on the 6150RF as indicated in the wiring table adjacent to Figure 2. 5. Connect the wires for the relay output (if used) to the terminals on the 6150RF’s PC board. 6. Reattach the keypad to its case back. Note: Upon power-up or exit of the Program Mode, the 6150RF alternately flashes "Ad" and the 2-digit keypad address and the 2-digit receiver address on the display. Press any key to display the system status. NOTE:TO REMOVE CASE BACKPUSH IN THE TWO MOUNTINGSNAPS LOCATED ALONG THE BOTTOM OF THE KEYPADAND LIFT UP.6150-006-V0RETAININGSNAPSARMEDREADYLOCKINGTAB Figure 1 – Removing the 6150RF Case Back PLEASE GO TO PAGE 8 FOR THEFCC AND IC STATEMENTS.
- 2 - WIRING TABLE Keypad Control Panel Wire Color ▲G Data In Green − − Aux Pwr (GND) Black + + Aux Pwr Red ▼Y Data Out Yellow Note: NO (normally Open) and C (common) are the connections for the relay output +6150RF-003-V2NO CYG Figure 2 - 6150RF Wiring Connections APPLICATION GUIDELINES Use the following guidelines when planning an installation: • Local wireless keys (wireless keys programmed directly into the 6150RF) may be used regardless of whether the RF receiver in the 6150RF is enabled or disabled. • If using bi-directional devices, be sure to enable the transmitter module in the 6150RF. • If transmitters are programmed into the control panel, be sure to enable the receiver. (Make sure you do not exceed the number of receivers supported by the control panel.) • If a local wireless key is programmed to arm/disarm or to trigger a relay on the control panel, a user code must be entered into the 6150RF. This user code must also be programmed into the control panel. • You must set the House ID only if you are using RF keypads and/or bi-directional devices; AND the House ID Source is the 6150RF (Local). 6150RF Application Guide The following guide outlines how to program the wireless keys, RF receiver, and the House ID in the 6150RF for your installation. * Two 6150RFs are needed for this application: one assigned to partition 1 and one assigned to partition 2. ** If using an RF keypad on only one partition, the 6150RF’s partition assignment in panel programming must match the partition. *** If set for Local on a partition control, the 6150RF’s partition assignment must match the one programmed in the BD device. Are you using 6150RF Programming Options System Control Panel RF keys beyond system’s capacity? RF receivers beyond system’s capacity? RF keypads and/or Bi-directional devices on more than 1 partition? Program Wireless Keys Into Receiver Enable House ID Source*** 4110DL, 4110XM, 4140XMP, VISTA-20HWSE N/A N/A N/A 6150RF OFF Local [0] NO NO N/A System ON [1] System [1] YES NO N/A 6150RF ON [1] System [1] VISTA-10P, VISTA-10SE, VISTA-15, VISTA-15P, VIA-30PSE YES YES N/A 6150RF OFF [0] Local [0] NO NO NO System ON [1] System [1] YES NO NO 6150RF ON [1] System [1] YES YES NO 6150RF OFF [0] Local [0] NO YES YES* System OFF [0] Local [0] VISTA-20SE, VISTA-20P YES YES YES* 6150RF OFF [0] Local [0] NO NO NO** System ON [1] System [1] YES NO NO** 6150RF ON [1] System [1] YES YES NO** 6150RF OFF [0] Local [0] NO YES YES System OFF [0] Local [0] VISTA-40, VISTA-50P, VISTA-128B, VISTA-128BP YES YES YES 6150RF OFF [0] Local [0]
Download:
Mirror Download [FCC.gov]
Document ID1283877
Application IDazj7i2W2Bv8x5l0znGt3Dw==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize31.19kB (389854 bits)
Date Submitted2010-05-19 00:00:00
Date Available2010-11-15 00:00:00
Creation Date2009-06-12 15:19:31
Producing SoftwareAcrobat Distiller 4.05 for Windows
Document Lastmod2009-06-12 16:05:18
Document TitleUsers Manual
FCC ID Filing: CFS8DL6150RFT3

Navigation menu