Ademco 8DLFA270RF keypad transceiver User Manual

Honeywell International Inc. keypad transceiver PREK14035 Rev A

a href="https://usermanual.wiki/Ademco" itemprop="url"> Ademco >

II with FCC Part 15 Statment and FCC ID Number

R PREK14035 9/05 Rev. A FA270RF Keypad/Transceiver INSTALLATION AND SETUP GUIDE About the FA270RF The FA270RF Keypad/Transceiver is a combination unit incorporating the functions of the following units:• FA270KP Fixed Addressable Keypad • 5881M RF Receiver • 5800TM Transmitter Module • Normally-open relay output. The FA270RF Keypad/Transceiver may also be used on any control panel that supports the FA260KP keypad. Features of the FA270RF Wireless Features • Supports up to eight wireless keys locally (programmed directly into FA270RF) without occupying any zones supported by the control panel. • Supports button-type transmitters (5804 and 5804BD) for local operation. • Supports a maximum of 16 transmitters programmed into any 5800 Series-supported control panel. • Provides low-battery indications for the local wireless keys. • Supports wireless keys with (high-security) (5804E). • Provides a nominal range of 200' for the RF transmitters (some transmitters have a shorter range). • Supports RF jam detection when the receiver is enabled. • Provides wireless key support for control panels that do not support RF themselves (e.g., FA110C). UL The following 5800 series transmitters are not intended for use in UL installations: 5802, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5804E, 5804WATCH, 5814, 5816TEMP, 5819, 5819BRS, 5819WHS, and 5850. Programming Features • Provides an Auto Enroll mode for programming of the wireless keys. • Provides a method for deleting a serial number and re-enrolling a new one in its place. • Provides default settings for the functions of the wireless keys. Additional Features • Sends status signals (Armed, Ready, etc.) to bi-directional units such as 5804BDV. • Operates the on-board relay in conjunction with the receiver (for example, to trip a garage door opener). Note: This particular feature is not intended for UL installations. • Can activate relays programmed into the control panel. • Provides an End User mode to enable/disable local wireless keys (for example, if a user accidentally loses a wireless key). Refer to the FA270RF User Guide for this procedure. Application Guidelines Use the following guidelines when planning an installation: • Local wireless keys are programmed directly into the FA270RF and may be used regardless of whether the RF receiver is enabled or disabled. • If using bi-directional devices, be sure to enable the transmitter module in the FA270RF. • If transmitters are programmed into the control panel, be sure to enable the receiver. (Make sure you do not exceed the number of receivers supported by the control panel.) • If a local wireless key is programmed to arm/disarm or to trigger a relay on the control panel, a user code must be entered into the FA270RF. • You must set the House ID only if you are using RF keypads and/or bi-directional devices AND the House ID source is the FA270RF (Local).
- 2 - Application Guide Below is a guide that outlines how to program the wireless keys, RF receiver, and the House ID in the FA270RF for your particular installation. Are you using FA270RF Programming Options Control Panel RF keys beyond system’s capacity? RF receivers beyond system’s capacity? RF keypads and/or Bi-directional devices on more than 1 partition? Program Wireless Keys Into Receiver Enable House ID Source*** FA110C, FA120C N/A N/A N/A FA270RF OFF Local [0] NO NO N/A System ON [1] System [1] YES NO N/A FA270RF ON [1] System [1] FA142C, FA148C, FA148CP YES YES N/A FA270RF OFF [0] Local [0] NO NO NO System ON [1] System [1] YES NO NO FA270RF ON [1] System [1] YES YES NO FA270RF OFF [0] Local [0] NO YES YES* System OFF [0] Local [0] FA162C, FA168CPS FA168C YES YES YES* Local OFF [0] Local [0] NO NO NO** System ON [1] System [1] YES NO NO** FA270RF ON [1] System [1] YES YES NO** FA270RF OFF [0] Local [0] NO YES YES System OFF [0] Local [0] FA1220CV, FA1340C YES YES YES FA270RF OFF [0] Local [0] * Two FA270RFs are needed for this application. One connected to partition 1’s keypad terminals and one connected to partition 2’s. ** If using an RF keypad on only one partition, the FA270RF’s partition assignment must match the partition set in field 1*48. *** If set for Local on a partition control, the FA270RF’s partition assignment must match the partition programmed in the BD device. An example of an installation using two FA270RF Keypad/Transceivers with 2-Way Wireless Devices on two partitions is shown below. Settings FA270RF #1 FA270RF #2 Keypad: Must be assigned to Partition 1 in the control panel Must be assigned to Partition 2 in the control panel House ID: Match Partition 1 House ID in the control panel and House ID in Wireless Device Match House ID in Wireless Device House ID Source: System Local Receiver Enable: On Off Transmitter Enable: On On Installing the FA270RF Locate the FA270RF in an area and at a height where it is convenient for users to operate the system. The FA270RF must be at least ten feet from the control panel to ensure proper operation of the RF receiver. DO+DINOCFA270RF-001-V0 Figure 1: FA270RF Wiring Connections Wiring Table Keypad Control Panel Wire Color DI Data In Green – – Aux Pwr (GND) Black + + Aux. Pwr Red DO Data Out Yellow To install the FA270RF, refer to Figure 1 and the Wiring Table for wiring connections and perform the following steps: Step Action 1 Remove the case back by pushing down the two snaps along the FA270RF’s bottom edge and pulling the case apart. 2 Route the wiring from the control panel through the opening in the case back. (See the control panel’s instructions for proper wire run lengths.) 3 Mount the case back directly to a wall or electrical gang box. 4 Connect the power and data wires from the control panel to the terminals on the FA270RF as indicated in the wiring table adjacent to Figure 1 above. 5 Connect the wires for the relay output (if used) to the terminals on the FA270RF’s PC board. 6 Reattach the keypad to its case back. 7 Remove the clear protective films from the LCD display and install the keypad labels, as required. Note: Upon power-up or exit of the Program Mode, the FA270RF alternately flashes "Ad" and the 2-digit keypad address and the 2-digit receiver address on the display. Press any key to display the system status. FA270RF #1 FA270RF #2 CONTROL PANEL
Download:
Mirror Download [FCC.gov]
Document ID618287
Application IDtCIWdUaC32nUV7M8mAEEZQ==
Document DescriptionII with FCC Part 15 Statment and FCC ID Number
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize12.21kB (152587 bits)
Date Submitted2006-01-10 00:00:00
Date Available2006-02-03 00:00:00
Creation Date2005-10-25 14:55:33
Producing SoftwareAcrobat Distiller 4.05 for Windows
Document Lastmod0000-00-00 00:00:00
Document TitleMicrosoft Word - PREK14035 Rev A.doc
Document CreatorPScript5.dll Version 5.2
Document Author: E653612
FCC ID Filing: CFS8DLFA270RF

Navigation menu