ADTRAN TRC4208 TRACER 4208 User Manual 612804208L1 1A

Adtran TRACER 4208 612804208L1 1A

UserManual.wiki >

ADTRAN >

TRC4208 User Manual

Manual

TRACER 4208 System Manual Revision History612804208L1-1A © 2003 ADTRAN, Inc. 3Revision HistoryDocument RevisionDate Description of ChangesA March 2003 Initial release of manual.Notes provide additional useful information.Cautions signify information that could prevent service interruption.Warnings provide information that could prevent damage to the equipment or endangerment to human life.

Safety Instructions TRACER 4208 System Manual 4 © 2003 ADTRAN, Inc. 612804208L1-1ASafety InstructionsWhen using your telephone equipment, please follow these basic safety precautions to reduce the risk of fire, electrical shock, or personal injury:1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.2. Avoid using a telephone (other than a cordless-type) during an electrical storm. There is a remote risk of shock from lightning.3. Do not use the telephone to report a gas leak in the vicinity of the leak.4. Use only the power cord, power supply, and/or batteries indicated in the manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for special disposal instructions.Save These Important Safety Instructions

TRACER 4208 System Manual FCC-Required Information612804208L1-1A © 2003 ADTRAN, Inc. 5FCC-Required InformationFederal Communications Commission Radio Frequency Interference StatementThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.Radio Frequency Interface StatementThis equipment has been tested and found to comply with the limits for an intentional radiator, pursuant to Part 15, Subpart C of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications.The limits are designed to provide reasonable protection against such interference in a residential situation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna of the affected radio or television.• Increase the separation between the equipment and the affected receiver.• Connect the equipment and the affected receiver to power outlets on separate circuits.• Consult the dealer or an experienced radio/TV technician for help.Shielded cables must be used with this unit to ensure compliance with Class A FCC limits.Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Changes or modifications not expressly approved by ADTRAN could void the user’s authority to operate the equipment.

FCC-Required Information TRACER 4208 System Manual 6 © 2003 ADTRAN, Inc. 612804208L1-1AFCC Output Power RestrictionsThe FCC does not require licensing to implement this device. License-free operation in the industrial, scientific, and medical band is documented in FCC Rules Part 15.247. It is the responsibility of the individuals designing and implementing the radio system to assure compliance with any pertinent FCC Rules and Regulations. This device must be professionally installed.Exposure to Radio Frequency FieldsThe TRACER 4208 is designed to operate at 5.8 GHz with 100 mW maximum transmit power.This level of RF energy is below the Maximum Permissible Exposure (MPE) levels specified in FCC OET 65:97-01. The installation of high gain antenna equipment in the system configuration may create the opportunity for exposure to levels higher than recommended for the general population at a distance less than 15 feet (4.6 meter) from the center of the antenna. The following precautions must be taken during installation of this equipment:• The installed antenna must not be located in a manner that allows exposure of the general population to the direct beam path of the antenna at a distance less than 15 feet (4.6 meters). Installation on towers, masts, or rooftops not accessible to the general population is recommended; or• Mount the antenna in a manner that prevents any personnel from entering the area within 15 feet (4.6 meter) from the front of the antenna.• It is recommended that the installer place radio frequency hazard warnings signs on the barrier that prevents access to the antenna.• Prior to installing the antenna to the TRACER 4208 output, make sure the power is adjusted to the settings specified in section 2 of this manual.• During antenna installation, be sure that power to the TRACER equipment is turned off in order to prevent any energy presence on the coaxial connector.• During installation and alignment of the antenna, do not stand in front of the antenna assembly.• During installation and alignment of the antenna, do not handle or touch the front of the antenna.These simple precautions must be taken to prevent general population and installation personnel from exposure to RF energy in excess of specified MPE levels.

TRACER 4208 System Manual Warranty and Customer Service612804208L1-1A © 2003 ADTRAN, Inc. 7Warranty and Customer ServiceADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty.Customer Service, Product Support Information, and TrainingADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty. A return material authorization (RMA) is required prior to returning equipment to ADTRAN. For service, RMA requests, training, or more information, use the contact information given below.Repair and ReturnIf you determine that a repair is needed, please contact our Customer and Product Service (CaPS) department to have an RMA number issued. CaPS should also be contacted to obtain information regarding equipment currently in house or possible fees associated with repair.Identify the RMA number clearly on the package (below address), and return to the following address:Pre-Sales Inquiries and Applications SupportYour reseller should serve as the first point of contact for support. If additional pre-sales support is needed, the ADTRAN Support web site provides a variety of support services such as a searchable knowledge base, latest product documentation, application briefs, case studies, and a link to submit a question to an Applications Engineer. All of this, and more, is available at:When needed, further pre-sales assistance is available by calling our Applications Engineering Department.CaPS Department (256) 963-8722 ADTRAN Customer and Product Service901 Explorer Blvd. (East Tower)Huntsville, Alabama 35806RMA # _____________http://support.adtran.comApplications Engineering (800) 615-1176

Customer Service, Product Support Information, and Training TRACER 4208 System Manual 8 © 2003 ADTRAN, Inc. 612804208L1-1APost-Sale SupportYour reseller should serve as the first point of contact for support. If additional support is needed, the ADTRAN Support web site provides a variety of support services such as a searchable knowledge base, updated firmware releases, latest product documentation, service request ticket generation and trouble-shooting tools. All of this, and more, is available at:When needed, further post-sales assistance is available by calling our Technical Support Center. Please have your unit serial number available when you call.Installation and Maintenance SupportThe ADTRAN Custom Extended Services (ACES) program offers multiple types and levels of installation and maintenance services which allow you to choose the kind of assistance you need. This support is available at:For questions, call the ACES Help Desk. TrainingThe Enterprise Network (EN) Technical Training Department offers training on our most popular products. These courses include overviews on product features and functions while covering applications of ADTRAN's product lines. ADTRAN provides a variety of training options, including customized training and courses taught at our facilities or at your site. For more information about training, please contact your Territory Manager or the Enterprise Training Coordinator.http://support.adtran.comTechnical Support (888) 4ADTRANhttp://www.adtran.com/acesACES Help Desk (888) 874-ACES (2237) Training Phone (800) 615-1176, ext. 7500 Training Fax (256) 963-6700Training Email training@adtran.com

612804208L1-1A © 2003 ADTRAN, Inc. 9Table of ContentsSection 1 System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11This section of ADTRAN’s TRACER 4208 System Manual is designed for use by network en-gineers, planners, and designers for overview information about the TRACER 4208.Section 2 Microwave Path Engineering Basics . . . . . . . . . . . . . . . . . . . . . . . . . . 13Explains the basics of analyzing a wireless microwave link or path. The significant parameters are defined, and several recommendations are offered.Section 3 Engineering Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Provides information to assist network designers with incorporating the TRACER 4208 system into their networks.Section 4 Network Turnup Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Provides shipment contents list, grounding instructions, mounting options, and specifics of sup-plying power to the unit.Section 5 User Interface Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Provides detailed descriptions of all menu options and configuration parameters available for the TRACER 4208.Section 6 Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Provides helpful information for troubleshooting common configuration problems for the TRACER 4208.

Table of Contents TRACER 4208 System Manual 10 © 2003 ADTRAN, Inc. 612804208L1-1A

612804208L1-1A © 2003 ADTRAN, Inc. 11SYSTEM DESCRIPTIONThis section of ADTRAN’s TRACER 4208 System Manual is designed for use by network engineers, planners, and designers for overview information about the TRACER 4208.It contains general information and describes physical and operational concepts, network relationships, provisioning, testing, alarm status, and system monitoring. This section should be used in conjunction with Section 3, Engineering Guidelines, of the system manual.CONTENTSSystem Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Configuration and Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Operational . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Section 1 System Description TRACER 4208 System Manual 12 © 2003 ADTRAN, Inc. 612804208L1-1A1. SYSTEM OVERVIEWThe ADTRAN TRACER® 4208 wireless system provides eight independent T1 circuits over a wireless link for up to 30 miles (line-of-sight path required). As authorized under Part 15.247 of the FCC Rules, the TRACER 4208 operates license-free in the 5.8 GHz Industrial, Scientific, and Medical (ISM) band. The ISM band requires no frequency coordination or licensing of end users.For configuration and testing, the TRACER 4208 provides the capability to control the remote system through a separate maintenance channel. The TRACER 4208 has several built-in test capabilities including remote loopback. Complete configuration and performance data is available through menus accessed using a standard RS-232 terminal interface.2. FEATURES AND BENEFITSThe following is a brief list of the TRACER 4208 features and benefits:Configuration and Management• Easy to use VT100 control port (RS-232 interface) for configuration and monitoring• Remote configuration over both ends of the wireless link, from each end of the linkOperational• Eight independent transparent T1 transmission paths, over digital microwave link• No license required per FCC Rules Part 15.247• Frequency: 5.725 to 5.850 GHz• Point-to-point, up to 30 miles• 1-U high unit for easy rack-mounting

612804208L1-1A © 2003 ADTRAN, Inc. 13 MICROWAVE PATH ENGINEERING BASICSExplains the basics of analyzing a wireless microwave link or path. The significant parameters are defined, and several recommendations are offered.CONTENTSLine-of-Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Decibels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Calculating the Fade Margin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Receiver Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Antenna Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Transmitted Power (PT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Carrier Wavelength (l) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Path Distance (d) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18System Losses (L) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Path Loss (LP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Receiver Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Antenna Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Antenna Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20TRACER RSSI Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Antenna Beam Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Fresnel Zones, Earth Curvature, & Antenna Heights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Other Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Path Availability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23FIGURESFigure 1. Example Microwave Path with Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Figure 2. Typical Antenna Beam Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21TABLESTable 1. Antenna Gain for Given Dish Diameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Table 2. Typical Coaxial Loss for Common Cable Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Table 3. Path Loss for Given Path Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Table 4. Minimum Antenna Height for Given Path Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Section 2 Microwave Path Engineering Basics TRACER 4208 System Manual 14 © 2003 ADTRAN, Inc. 612804208L1-1A

TRACER 4208 System Manual Section 2 Microwave Path Engineering Basics612804208L1-1A © 2003 ADTRAN, Inc. 151. LINE-OF-SITEThe TRACER 4208 system is designed for operation in the license-free 5.725 GHz to 5.850 GHz industrial, scientific and medical (ISM) band. Radio wave propagation in this band exhibits microwave characteristics which are ideally suited for point-to-point, line-of-sight communications. Line-of-Sight requires that the transmitting antenna and receiving antenna are able to “see” each other, and that the straight-line path between the two antennas is free of obstructions, such as buildings, trees, mountains, and, in longer paths, even the curvature of the earth. In addition, for maximum signal strength the area around the visual line-of-sight where microwave signals reflect (Fresnel zone) must also be free of obstructions. Fresnel zones are discussed in more detail on page 21.Terminology2. DECIBELSUnderstanding the decibel (dB) format is key when discussing microwave path engineering because the received signal power is often expressed in decibel format. In general, any quantity can be expressed in decibels. If the quantity x is a power level (in Watts), the decibel equivalent is defined asIf the quantity x is referenced to a milliwatt (mW), then the decibel-milliwatt (dBm) is used instead of a generic decibel.Using the decibel format simplifies power calculations by reducing multiplication and division operations into addition and subtraction operations.3. CALCULATING THE FADE MARGINThe fade margin (F ) is a value indicating the amount of extra signal power available to the receiver to operate at a maximum bit error rate (BER). Fade margin is simply the difference between the available signal power at the receiver (PR ) and the receiver sensitivity (Psens ). Point-to-Point Wireless communication from a single site to another individual site. Contrast with point-to-multipoint.Line-of-Sight An unobstructed, direct path exists between the transmitting and the receiving antennas.It is imperative to determine if the proposed microwave path is suitable (at a minimum) for ideal, nondistorted signals before attempting installation.xdB 10 log10 x()⋅=(dB)xdBm 10 log10x1mW-------------⋅=(dBm)FPRPsens–=(dB)

Section 2 Microwave Path Engineering Basics TRACER 4208 System Manual 16 © 2003 ADTRAN, Inc. 612804208L1-1AHigher levels of fade margin indicate stronger protection against signal fading and a more reliable link. For most applications, 20 to 30 dB of fade margin should ensure a reliable link. The following sections further discuss the necessary power calculations and their components.4. RECEIVER POWERThe viability of a particular microwave path is determined by the power of the transmitted microwave signal, the transmit and receive antenna gain, distance, and accumulated system losses (such as RF coaxial cable losses and path loss).The equation relating received signal power to the other microwave parameters isor (in decibel notation)where the variables in the equation are defined asPRreceived power (Watts)PTtransmitted power (100 mW (max) for TRACER 4208 - adjustable)GTtransmit antenna gainGRreceive antenna gainλcarrier wavelength (meters)dpath distance (meters)Lother losses (RF coaxial cable, etc.)LPpath loss (dB)Figure 1 on page 17 illustrates a wireless link configuration containing all the parameters necessary for the power budget analysis.When using decibel notation, all quantities must be individually converted to decibels prior to performing addition and subtraction.PRPTGTGRλ24π()2d2L------------------------------=(Watts, W)(decibels referenced to a Watt, dBW)PR = PT + GT + GR - L - LP

TRACER 4208 System Manual Section 2 Microwave Path Engineering Basics612804208L1-1A © 2003 ADTRAN, Inc. 17Figure 1. Example Microwave Path with ParametersThe following sections further discuss the power budget analysis and its components.Antenna GainActual transmit and receive antenna gain values depend strictly upon the physical characteristics of the antennas installed for each link. In other words, the size of the dish determines the antenna gain. Using a parabolic dish antenna results in the best performance. Antenna gains are specified in terms of decibels of gain referenced to an isotropic source (dBi). An isotropic source is a hypothetical antenna having equal radiation in all directions. Typical antenna gains are listed in Table 1; however, dish manufacturers can provide gains for specific types of antennas.Transmitted Power (PT)The FCC specifies the maximum transmitter power used for antennae of a given gain. FCC Rules Part 15, Subpart 247 allow for a maximum power of 1 Watt (30 dBm) into antennae of a gain less than or equal to 6 dBi. Since the TRACER 4208 maximum transmit power is 100 milliwatts, there is no reduction in transmitter output power required for antennae gains greater than 6 dBi.Table 1. Antenna Gain for Given Dish DiametersDish Diameter(in feet)Gain at 5.8 GHz(in dBi)228.5434.2637.5840.710 42.512 44.2 GTGRd, LPPTPRλLL

Section 2 Microwave Path Engineering Basics TRACER 4208 System Manual 18 © 2003 ADTRAN, Inc. 612804208L1-1ACarrier Wavelength (λ)The carrier wavelength is the physical wavelength of the main RF carrier being used for communication, and is usually approximated at the center frequency of the band (which is 5787.5 MHz for the TRACER 4208). The carrier wavelength calculations follow:λ = c / f (meters)where c = speed of light (in meters)f = frequency (in Hz)resulting in the following carrier wavelength:λ = 3.00 x 10¯8 / 5787.5 x 10 5 = 0.0518 m or 5.18 cmPath Distance (d)The path distance is simply the physical distance between the transmit and receive antennas. For the TRACER 4208, these distances can range up to 30 miles. System Losses (L)System losses are defined by RF coaxial cable loss, connector losses, and losses added from any additional lightning protection devices for the power budget analysis. Coaxial cable is required to attach the TRACER 4208 to the antenna. The length of the cable varies from a few feet to several feet, depending upon your application and the proximity of the TRACER 4208 to the antenna. Various grades of coaxial cable will work sufficiently well for connecting the TRACER 4208 unit to the antenna. A low-loss coaxial cable will minimize cable losses.One end of the coaxial cable requires an N-type male connector (plug) to mate with the TRACER 4208 unit. The other end of the coaxial cable requires a connector compatible with the antenna chosen for the installation (usually an N-type male connector). Additionally, ADTRAN recommends that the outdoor connector on the coaxial cable be weatherproofed to prevent corrosion and electrical shorting.In areas where lightning strikes are frequent, a lightning arrestor should be installed directly on the antenna coaxial cable. Installing lightning arrestors helps protect the RF electronics in the downstream path from damaging voltages and currents (including the TRACER 4208 unit).

TRACER 4208 System Manual Section 2 Microwave Path Engineering Basics612804208L1-1A © 2003 ADTRAN, Inc. 19Table 2 gives typical loss figures for some of the more common coaxial cable types (per 100 feet).Path Loss (LP)Path loss is the estimated attenuation between the transmit and receive antennas caused by signal separation and scattering. The path loss is considered basic transmission loss over the microwave link. The following expression calculates path loss:where fcarrier frequency (Hz)λcarrier wavelength (c / f) (meters)dpath distance (meters)cspeed of light, free-space (meters)orwhere d is expressed in miles and f in GHzPath loss, as shown here, increases rapidly as either the path length increases or the carrier wavelength decreases (which happens as the carrier frequency increases). Therefore, longer microwave paths naturally experience more path loss than shorter paths. Likewise, higher frequency microwave communication experiences more path loss than lower frequency microwave communication.Table 2. Typical Coaxial Loss for Common Cable TypesCable Type5.8 GHz Loss/100 ft. (in dB)RG58 N/ARG8 (air) N/ARG8 (foam) N/A1/4” Coax 11.363/8” Coax 9.651/2” Coax 6.495/8” Coax 4.907/8” Coax N/A1 1/4” Coax N/A1 5/8” Coax N/A5.8 GHz Elliptical Waveguide 1.23LP4πdλ----------24πdfc------------2== (dB)LP96.6 20 log10 d() 20·log+10 f()⋅+= (dB)

Section 2 Microwave Path Engineering Basics TRACER 4208 System Manual 20 © 2003 ADTRAN, Inc. 612804208L1-1ATable 3 lists path loss values for various path lengths for the TRACER 4208 5.8 GHz system. Values not listed in the table can be interpolated from those listed.5. RECEIVER SENSITIVITYReceiver sensitivity is a value expressed in decibels referenced to one milliwatt (dBm) that corresponds to the minimum amount of signal power needed at the receiver to achieve a given bit error rate (BER). Receiver sensitivity is usually a negative number of decibels and smaller receiver sensitivity (higher quantity negative number) is better for a given BER. Several factors affect receiver sensitivity including the data bandwidth of the wireless link, and the amount of additional signal degradation introduced in the receiver electronics. The receiver sensitivity of the TRACER 4208 is -90 dBm at 10-6 BER.6. ANTENNA INFORMATIONThe overall wireless system is directly affected by the antenna selection and installation. The following sections discuss several factors concerning antenna selection and installation.Antenna AlignmentWith line-of-sight microwave communications, optimum system performance requires that the transmitting and receiving antennas are properly aligned. This ensures maximum received signal power at each receiver. Antenna alignment must be achieved in both azimuth (along a horizontal plane) and elevation (along a vertical plane). A received signal strength indicator (RSSI) aids the equipment installer in determining when alignment is maximized by simply ensuring maximum RSSI. Table 3. Path Loss for Given Path LengthsPath Length(miles)Path Loss(dB)1112211831214124512610 13215 13520 13825 14030 14135 143Should an interferer be present nearby, three software selectable bandplans are provided for frequency agility. Changing the TRACER 4208 bandplan does not require additional components, or opening of the radio. See TRACER System Configuration > RF Bandplan on page 47 for additional details.

TRACER 4208 System Manual Section 2 Microwave Path Engineering Basics612804208L1-1A © 2003 ADTRAN, Inc. 21TRACER RSSI Test PointsThe RSSI indicator for the TRACER 4208 system is provided through the VT100 terminal menus accessed through the RS-232 interface, and it is presented as a series of bars indicating signal strength. More bars means more RSSI, which ensures more received signal strength and better link performance.If the local system has acquired a useful signal from the remote system, then the remote TRACER 4208 RSSI can be viewed from the local TRACER 4208 VT100 terminal menu interface.An RSSI test point, located on the front panel, represents the voltage (relative to the GND test point) of a relative signal level of receive strength from the far end. The voltage at this test point can vary from approximatly 0 to greater than 4 Volts DC, with 0 Volts corresponding to no signal and 4 Volts or better to full signal strength.Antenna Beam PatternsDirectly related to the subject of antenna alignment is the topic of antenna beam patterns. Antennas used with the TRACER 4208 system have a particular beam shape determined in part by the physical construction and geometry of the antenna. The antenna beam patterns are characterized by a dominant main lobe, which is the preferred lobe to use for point-to-point communications, and several side lobes, as shown in Figure 1. When setting up a microwave link, antenna alignment is nothing more than steering the main lobes of both antennas until the main lobe of one transmitter is centered on the receiving element of the receiving antenna.Figure 2. Typical Antenna Beam PatternAntennas are also designed to radiate RF energy efficiently for a specific range of frequencies. Please consult the data sheet for your particular antenna make and model to ensure that it is specified to operate in the 5725 MHz to 5850 MHz frequency band for the TRACER 4208 system.Fresnel Zones, Earth Curvature, & Antenna HeightsFresnel zones correspond to regions in the microwave path where reflections of the intended signal occur and combine in both constructive and destructive manners with the main signal, thereby either enhancing or reducing the net power at the receiver.In general, the odd numbered Fresnel zones (1, 3, 5, ...) add constructively at the receiver, while the even numbered Fresnel zones (2, 4, 6, ...) add destructively at the receiver.

Section 2 Microwave Path Engineering Basics TRACER 4208 System Manual 22 © 2003 ADTRAN, Inc. 612804208L1-1AThe first Fresnel zone corresponds to the main lobe, 60% of which must be free of physical obstructions for the path calculations to be valid. Since the main lobe contains the vast majority of the microwave energy, this zone is typically used to determine proper antenna heights when placing antennas on towers or buildings.The curvature of the Earth becomes a legitimate obstruction for path lengths of 7 miles or greater, and must also be accounted for when determining minimum antenna heights.The aggregate expression for minimum antenna height that incorporates both the 60% first Fresnel zone and the Earth’s curvature is given bywhere f is in GHz and d is in miles.Table 4 tabulates minimum antenna heights for given path lengths.Table 4. Minimum Antenna Height for Given Path LengthsPath Length(miles)Min. Antenna Height(ft)22243264185010 6014 8116 9218 10420 11722 13124 14526 16128 17730 19432 21334 23236 252h72.1d4f-----0.125d2+= (feet)

$TRACER 4208 System Manual Section 2 Microwave Path Engineering Basics612804208L1-1A © 2003 ADTRAN, Inc. 237. OTHER CONSIDERATIONSPath AvailabilityThe path availability of a wireless link is a metric that expresses the fractional amount of time a link is available over some fixed amount of time, and depends on several factors. Path availability is expressed aswhere the parameters areaterrain factorbclimate factorfcarrier frequency (GHz)dpath length (miles)Ffade margin (dB)Terrain Factor (a)The terrain factor is a quantity that compensates the link availability for different types of terrain. Generally speaking, the more smooth an area's terrain is, the less availability a wireless link running over that terrain will have, primarily due to multipath reflections. In contrast, secondary microwave signals will be randomly dispersed over rough terrain, and will not interfere with the main signal lobe as badly as in the smooth terrain case. The terrain factor values normally used are listed below:Climate Factor (b)The climate factor is a quantity that compensates the link availability for different types of climates (weather). In general, microwave links operating in areas with high humidity will have less availability than those in arid areas, primarily because water is a dispersive mechanism to microwave energy, and causes the main signal lobe to refract and disperse away from the receiver location. The climate factor values normally used are listed below:Terrain Terrain Factor DescriptionSmooth 4water, flat desertAverage 1moderate roughnessMountainous 1/4 very rough, mountainousClimate Climate Factor DescriptionVery Dry 1/8 desert regionsTemperate 1/4 mainland, interior regionHumid 1/2 humid and coastal regionsA12.5106–×()abfd310 F10⁄–()–[]100%×=(%)$

Section 2 Microwave Path Engineering Basics TRACER 4208 System Manual 24 © 2003 ADTRAN, Inc. 612804208L1-1A

612804208L1-1A © 2003 ADTRAN, Inc. 25ENGINEERING GUIDELINESProvides information to assist network designers with incorporating the TRACER 4208 system into their networks.CONTENTSEquipment Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Reviewing the Front Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26RSSI Monitoring Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26TX PWR Monitoring Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Reviewing the TRACER 4208 Rear Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28RS-232 Connection (DB-25) — Terminal Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28RS-232 Connection (Modem Use) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Test (1/4” bantam). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30T1 Connections (RJ-48C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Alarm Contacts (Plug-In Terminal Block) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31DC Power Connection (Plug-In Terminal Block) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Antenna Interface (N-Type connector) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32At-A-Glance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32FIGURESFigure 1. TRACER 4208 Front Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Figure 2. TRACER 4208 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28TABLESTable 1. TRACER 4208 Front Panel Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Table 2. TRACER 4208 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Table 1. Rear Panel Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Table 2. RS-232 Connection Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Table 3. TRACER 4208 (DCE) to Terminal (DTE) Diagram (DB-25) . . . . . . . . . . . . . . . . . . . . . . 29Table 4. TRACER 4208 (DCE) to Personal Computer (DB-9) . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Table 5. TRACER 4208 (DCE) to Modem (DCE - DB-25) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Table 6. T1 Interface Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Table 7. Alarm Contact Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Table 8. DC Power Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Table 9. At-A-Glance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Section 3 Engineering Guidelines TRACER 4208 System Manual 26 © 2003 ADTRAN, Inc. 612804208L1-1A1. EQUIPMENT DIMENSIONSThe TRACER 4208 unit is 17.12” W, 10.80” D, and 1.72” H, weighs 7 lbs, and can be used in 19 or 23-inch rack-mount configurations.2. POWER REQUIREMENTSThe TRACER 4208 system has a maximum power consumption of 18 W and a maximum current draw of 0.86 A (at 21 VDC).3. REVIEWING THE FRONT PANEL DESIGNThe front panel contains RSSI and TX PWR monitoring interfaces, a GND interface for reference with the monitoring interfaces, and status LEDs to provide visual information about the TRACER 4208 system. Figure 1 identifies the various bantam interfaces and the LEDs.Figure 1. TRACER 4208 Front Panel LayoutRSSI Monitoring InterfaceThe RSSI voltage is a function of the signal strength at the receiver and is used to measure the received signal strength. RSSI varies approximately from 0 to greater than 4 Volts (V), with 0V corresponding to a weaker received signal and 4V or better corresponding to a stronger received signal.TX PWR Monitoring InterfaceThe TX PWR voltage is a function of the selected transmit power level. This voltage ranges approximately from 0 to 5V, with 0V corresponding to +5 dBm (3 milliwatts) and 5V corresponding to +20 dBm(100 milliwatts).The voltage level present at the RSSI test point represents only a relative signal level of receive strength from the far end. No direct correlation can be made between RSSI voltage levels and actual receive levels in dBm. This test point is provided to assess relative signal level for alignment of antennas.ALARMT1A T1B T1C T1D T1E T1F T1G T1HTRACER 4208Status LEDsTX PWRRSSI GND

TRACER 4208 System Manual Section 3 Engineering Guidelines612804208L1-1A © 2003 ADTRAN, Inc. 27Front Panel LEDsWith the TRACER 4208 powered-on, the front panel LEDs provide visual information about the status of the TRACER 4208 system. Table 1 provides a brief description of the front panel features, and Table 2 provides detailed information about the LEDs. Table 1. TRACER 4208 Front Panel DescriptionFeature DescriptionRSSI Interface DC voltage indicating strength of the received signal at the antennaTX PWR Interface DC voltage indicating strength of transmitted signalGND Interface Ground reference for RSSI and TX PWR interfacesStatus LEDs Status information about the systemTable 2. TRACER 4208 LEDsFor these LEDs... This color light... Indicates that...PWRGreen (solid) the TRACER 4208 is connected to a power source.Off the TRACER 4208 is not currently powered up.PLAN AGreen (solid) the TRACER 4208 is transmitting on Frequency Plan A.Off the TRACER 4208 is not transmitting on Frequency Plan A.PLAN BGreen (solid) the TRACER 4208 is transmitting on Frequency Plan B.Off the TRACER 4208 is not transmitting on FrequencyPlan B.RF DOWN Red (solid) there is a communication problem between the local and remote TRACER 4208 systems.T1 AlarmsT1A....T1HRed (solid) an Alarm Condition on a T1 Interface. Check the respective T1 status page to identify the active alarm.Red (blinking) the respective T1 is in a loopback mode.RF LOW Red (solid) the RSSI level is below suggested minimum threshold (approximately 10 dBm above the minimum receive sensitivity).TST Amber (solid) there is an active test being performed by the system or there is an active loopback.

Section 3 Engineering Guidelines TRACER 4208 System Manual 28 © 2003 ADTRAN, Inc. 612804208L1-1A4. REVIEWING THE TRACER 4208 REAR PANEL DESIGNFigure 2 identifies the various features of the TRACER 4208 rear panel and Table 1 provides a brief description of each interface. Figure 2. TRACER 4208 Rear PanelRS-232 Connection (DB-25) — Terminal UseThe RS-232 connector provides a female DB-25 terminal connection (wired as a DCE interface), which is used for terminal access to the TRACER 4208 system. The RS-232 port provides the following functions:• Accepts EIA-232 input from a PC or terminal for controlling the TRACER 4208 system• Operates at 9600 bpsTable 2 on page 29 shows the pinout. Wiring diagrams for connecting to the RS-232 connector (for various applications) are provided following the pinout.Table 1. Rear Panel Description11 Detailed discussions (including pinouts) of rear panel components (where applicable) follow the table.Name Connector DescriptionARS-232 DB-25 (female) VT100 terminal (or PC with terminal emulation software) connectionBTes t 1/4” bantam Factory test connectionCT1A - T1H RJ-48C T1 device connectionDAlarm Terminal block External alarm monitoring system connectionEDC Power Terminal block 21-60 VDC power source connectionFFuse N/A 1 A, 250 V, 2 inch slow-blo fuseGAntenna N-Type Antenna feedline cable connectionHGround Lug N/A Earth ground connectionAT1A T1B T1C T1DT1E T1F T1G T1HAntennaDC PowerConnection ConnectorT1 InterfacesRS232 Interface(VT100 Terminal)GroundLugFuseAlarmContactsTestEGBCDFH

TRACER 4208 System Manual Section 3 Engineering Guidelines612804208L1-1A © 2003 ADTRAN, Inc. 29Table 2. RS-232 Connection Pinout PIN NAME DESCRIPTION1, 7 GND Ground2TX Transmit3RX Receive4RTS Request To Send5CTS Clear To Send6DSR Data Set Ready (Modem Control Only)8CD Carrier Detect9-19 —Unused20 DTR Data Terminal Ready (Modem Control Only)21 —Unused22 RI Ring Indicator23-25 —UnusedTable 3. TRACER 4208 (DCE) to Terminal (DTE) Diagram (DB-25)PIN NAME PIN NAME2TX 2TX3RX 3RX4RTS 4RTS5CTS 5CTS6DSR 6DSR7 GND 7 GNDTable 4. TRACER 4208 (DCE) to Personal Computer (DB-9)PIN NAME PIN NAME2TX 2TX3RX 3RX4RTS 7RTS5CTS 8CTS6DSR 6DSR7 GND 5 GND

Section 3 Engineering Guidelines TRACER 4208 System Manual 30 © 2003 ADTRAN, Inc. 612804208L1-1ARS-232 Connection (Modem Use)Modem controls, discussed in Section 5, User Interface Guide, enable or disable modem control through the RS-232 interface. When this option is enabled from a standard terminal connection, all RS-232 communications cease until a modem with a null modem adapter is attached between the TRACER 4208 and the data modem. Configure the data modem for AUTO ANSWER and 9600 BPS. When the user connects via the modem to the TRACER 4208 unit, communications via the RS-232 port resume. If a user accidentally enables modem control from a terminal and disrupts the RS-232 communication, pressing <Ctrl + Z> three times will temporarily disable the modem control option (until the system is reset) and will access the system configuration to disable modem control.The TRACER 4208 must be interfaced to a modem via an RS-232 null modem adapter or cable. The null modem converts Clear To Send (CTS) and Data Set Ready (DSR) into Ready To Send (RTS) and Data Terminal Ready (DTR), respectively. These signals indicate (to most modems) that a valid DTE terminal device is present. The null modem interface must route Carrier Detect (CD) on pin 8 directly from the modem. When using the RS-232 interface for modem control, the modem must source CD only when actually connected to a carrier.When MODEM CONNECTION is selected in the menu system, the TRACER 4208 will de-assert DTR and DSR for a time greater than 20 msec. The null modem consequently drops DTR and RTS at the modem interface, signaling the modem to hang up the line. If password functionality is enabled in the TRACER 4208, selecting MODEM CONNECTION resets the TRACER 4208 to the password entry screen.Table 5 contains the wiring diagram needed for connecting the TRACER 4208 RS-232 interface to a modem using the null modem adapter.Hangup-on-DTR-drop may need to be explicitly enabled on some modems.Table 5. TRACER 4208 (DCE) to Modem (DCE - DB-25)PIN NAME PIN NAME2TX 3RX3RX 2TX4RTS 5CTS5CTS 4RTS6DSR 20 DTR7GND 7 GND8CD 8CD

TRACER 4208 System Manual Section 3 Engineering Guidelines612804208L1-1A © 2003 ADTRAN, Inc. 31T1 Connections (RJ-48C)The physical T1 interfaces are provided by eight RJ-48C jacks that comply with the applicable ANSI and AT& T® standards.Alarm Contacts (Plug-In Terminal Block)Normally open (NO) and normally closed (NC) alarm contacts are provided on the rear panel of the TRACER 4208 system. In normal operation, the NC contact is electrically connected to the common contact (COM) and the NO contact is isolated. During an alarm condition, the NC contact becomes isolated and the NO is electrically connected to COM. This allows alarm conditions to be reported to external alarm monitoring systems.DC Power Connection (Plug-In Terminal Block)The TRACER 4208 can operate from a supply between 21 and 60 VDC, with either polarity referenced to ground, and consumes less than 18 Watts (W). Power supplies should be able to provide up to 25 W atthe selected voltage. Current required (in Amps) is determined by dividing the power consumed (in Watts) by the applied voltage (in Volts). For example, at 48 V, TRACER 4208 would draw approximately 0.375 A (18 W/48 V).FuseThe fuse holder, accessible from the rear panel of the TRACER 4208, accepts a generic 1 A, 250 V, 2-inch slow-blo fuse.Table 6. T1 Interface Connector PinoutPIN NAME DESCRIPTION1RTransmit data (ring) towards the network2 T Transmit data (tip) towards the network3, 6-8 UNUSED —4R1 Receive data (ring) toward the network5T1 Transmit data (tip) from the networkTable 7. Alarm Contact Connector PinoutPIN NAME DESCRIPTION1 COM Common Contact2NO Normally-Open Contact3NC Normally-Closed ContactTable 8. DC Power Connector PinoutPIN NAME DESCRIPTION1 + Positive Lead (referenced to ground)2 - Negative Lead (referenced to ground)

Section 3 Engineering Guidelines TRACER 4208 System Manual 32 © 2003 ADTRAN, Inc. 612804208L1-1AAntenna Interface (N-Type connector)The ANTENNA interface (N-Type connector) connects to the customer-supplied antenna using standard antenna feedline cable. When determining the cable specifications for your application, refer to Section 2, Microwave Path Engineering Basics (System Losses (L) on page 18) for a discussion on cable length and loss factors.5. AT-A-GLANCE SPECIFICATIONSThe following is a list of specifications for the TRACER 4208 system.Table 9. At-A-Glance Specifications Hardware Description SpecificationTransmitterOutput Power +20 dBm, maxFrequency Range 5725 to 5850 MHzReceiverReceive Level, Minimum -86 dBm Receive Level, Maximum -30 dBmReceive Level, Nominal -55 dBmFrequency PlanPlan ABand Plan1Tx 5.742 GHz, Rx 5.815 GHz 2Tx 5.747 GHz, Rx 5.827 GHz 3Tx 5.753 GHz, Rx 5.833 GHz Plan BBand Plan1Tx 5.815 GHz, Rx 5.742 GHz2Tx 5.827 GHz, Rx 5.747 GHz3Tx 5.833 GHz, Rx 5.753 GHz T1 InterfaceCapacity 1.544 Mbps (each)Connection RJ-48C jacksLine Code B8ZS, AMIFraming ESF, D4Alarms AIS, Red, Yellow, BPVs, LOSLoopbacks Local and remote (line and link)

TRACER 4208 System Manual Section 3 Engineering Guidelines612804208L1-1A © 2003 ADTRAN, Inc. 33User InterfacePanel Alarm LEDsDiagnostics Line and Link LoopbacksTes t P oin ts RSSI and TX PWRAlarms Normally Open (NO) and Normally Closed (NC)VT100 TerminalMenu Driven User Interface, Control of the Remote End, Loopback Test, Optional Password Protection, Event HistoryVT100 Terminal InterfaceData Rate 9600 bpsData Bits 8Parity NoneStop Bits 1Terminal Emulation VT100Mechanical and EnvironmentalOperating Temperature -25° C to 65° CSize 17.12” W x 10.80” D x 1.72” HHumidity 95%, Non-condensingWeight 7 lbsPowerInput Voltage 21 to 60 VDC, either polarity referenced to groundPower Consumption < 18 WattsConnector 2 pin terminal block (DC)Fuse 1A, 250V slow-blo fuse (2-inch)Table 9. At-A-Glance Specifications (Continued)Hardware Description Specification

Section 3 Engineering Guidelines TRACER 4208 System Manual 34 © 2003 ADTRAN, Inc. 612804208L1-1A

612804208L1-1A © 2003 ADTRAN, Inc. 35NETWORK TURNUP PROCEDUREProvides shipment contents list, grounding instructions, mounting options, and specifics of supplying power to the unit.CONTENTSIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Unpack and Inspect the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Contents of ADTRAN Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Customer Provides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Grounding Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Supplying Power to the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Mounting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Connecting the T1 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39FIGURESFigure 1. 5.8 GHz Bandwidth Division. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Section 4 Network Turnup Procedure TRACER 4208 System Manual 36 © 2003 ADTRAN, Inc. 612804208L1-1A1. INTRODUCTIONThis section discusses the installation process of the TRACER 4208 system.2. TOOLS REQUIREDThe tools required for the installation of the TRACER 4208 are:• VT100 terminal or PC with terminal emulation software• RS-232 (DB-25 male for TRACER 4208) cable for connecting to terminal3. UNPACK AND INSPECT THE SYSTEMEach TRACER 4208 is shipped in its own cardboard shipping carton. Open each carton carefully and avoid deep penetration into the carton with sharp objects. After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in transit, immediately file a claim with the carrier, then contact ADTRAN Customer Service (see Customer Service, Product Support Information, and Training information in the front of this manual).Contents of ADTRAN ShipmentYour ADTRAN shipment includes the following items:• TRACER 4208 Unit• TRACER 4208 Documentation CD• Eight T1 Crossover (RJ-48 to RJ-48) Cables • Eight T1 Straight Through (RJ-48 to RJ-48) CablesCustomer ProvidesThe following items are necessary for the installation of the TRACER 4208 system and are not provided by ADTRAN:• 21 to 60 VDC power source (or AC adapter available from ADTRAN P/N 1280650L1), either polarity referenced to ground• Antenna and mounting hardware• Antenna feedline cable• Lightning arrestors• Weatherproofing kits for antenna installationChanges or modifications not expressly approved by ADTRAN could void the user’s authority to operate the equipment.To prevent electrical shock, do not install equipment in a wet location or during a lightning storm.

TRACER 4208 System Manual Section 4 Network Turnup Procedure612804208L1-1A © 2003 ADTRAN, Inc. 374. CHANNEL SELECTIONThe FCC has allocated 125 MHz of spectrum in the 5.8 GHz band where the TRACER 4208 operates. Figure 1 illustrates the bandwidth division. Figure 1. 5.8 GHz Bandwidth DivisionTo designate the utilization of the ISM bandwidth, there are two different channel plans, labeled A and B. The letter of each channel plan setting is preset by the factory and refers to the physical configuration of the diplexer filter inside the environmental housing. Each channel is then divided into three bandplans (1, 2 or 3). The bandplans must be the same for the local and remote TRACER 4208. For example, the transmitter at one end of the link will transmit in bandplan 1 of channel A (the lower portion of the spectrum) and receive in bandplan 1 of channel B (the upper portion). Consequently, the receiver at the other end should receive in bandplan 1 of channel A (the lower portion) and transmit in bandplan 1 of channel B (the upper portion).The letter of the channel plan (A or B) must be different on both ends and the number of the bandplan (1, 2, or 3) must be the same on both ends. The default bandplan configuration for the TRACER 4208 is bandplan 1.The channel plan (A or B) of the unit may be changed in the field, if necessary, by rewiring the internal diplexer. Contact ADTRAN Technical Support for more information on this procedure.ChannelA57425725 5787 58505747 5753MHz MHzBandplan3Bandplan2Bandplan1ChannelB5815 5827 5833Bandplan3Bandplan2Bandplan1

Section 4 Network Turnup Procedure TRACER 4208 System Manual 38 © 2003 ADTRAN, Inc. 612804208L1-1A5. GROUNDING INSTRUCTIONSThe following provides grounding instruction information from the Underwriters’ Laboratory UL 60950 Standard for Safety of Information Technology Equipment Including Electrical Business Equipment, of December, 2000.An equipment grounding conductor that is not smaller in size than the ungrounded branch-circuit supply conductors is to be installed as part of the circuit that supplies the product or system. Bare, covered, or insulated grounding conductors are acceptable. Individually covered or insulated equipment grounding conductors shall have a continuous outer finish that is either green, or green with one or more yellow stripes. The equipment grounding conductor is to be connected to ground at the service equipment.The attachment-plug receptacles in the vicinity of the product or system are all to be of a grounding type, and the equipment grounding conductors serving these receptacles are to be connected to earth ground at the service equipment.A supplementary equipment grounding conductor shall be installed between the product or system and ground that is in addition to the equipment grounding conductor in the power supply cord.The supplementary equipment grounding conductor shall not be smaller in size than the ungrounded branch-circuit supply conductors. The supplementary equipment grounding conductor shall be connected to the product at the terminal provided, and shall be connected to ground in a manner that will retain the ground connection when the product is unplugged from the receptacle. The connection to ground of the supplementary equipment grounding conductor shall be in compliance with the rules for terminating bonding jumpers at Part K or Article 250 of the National Electrical Code, ANSI/NFPA 70. Termination of the supplementary equipment grounding conductor is permitted to be made to building steel, to a metal electrical raceway system, or to any grounded item that is permanently and reliably connected to the electrical service equipment ground.The supplemental grounding conductor shall be connected to the equipment using a number 8 ring terminal and should be fastened to the grounding lug provided on the rear panel of the equipment. The ring terminal should be installed using the appropriate crimping tool (AMP P/N 59250 T-EAD Crimping Tool or equivalent.)The supplemental equipment grounding terminal is located on the rear panel of the TRACER 4208.• This unit shall be installed in accordance with Article 400 and 364.8 of the NEC NFPA 70 when installed outside of a Restricted Access Location (i.e., central office, behind a locked door, service personnel only area).• Power to the TRACER 4208 DC system must be from a reliably grounded 21-60 VDC source which is electrically isolated from the AC source.• The branch circuit overcurrent protection shall be a fuse or circuit breaker rated minimum 60 VDC, maximum 10A.• A readily accessible disconnect device that is suitably approved and rated shall be incorporated in the field wiring.

TRACER 4208 System Manual Section 4 Network Turnup Procedure612804208L1-1A © 2003 ADTRAN, Inc. 396. SUPPLYING POWER TO THE UNITThe TRACER 4208 can operate from a supply between 21 and 60 VDC, with either polarity referenced to ground. Power supplies should be able to provide up to 25 watts at the selected voltage. A dual pin terminal plug accepts power at the rear panel of the unit, providing a + and - polarity reference point. Adapters for this plug are available (P/N 1175043L2) and are furnished with the unit and optional power supply (P/N 1280650L1).7. MOUNTING OPTIONSInstall the TRACER 4208 in a location that requires minimal antenna feedline length (the loss in this cable directly affects overall system performance). The TRACER 4208 is designed to be mounted in a rack. If multiple units are installed in one location, one half inch of spacing is recommended above and below the unit.8. CONNECTING THE T1 INTERFACEThe physical T1 interface is provided using eight RJ-48C jacks for transmit and receive. The provided straight through T1 interface cables can be used to interface to any standard T1 DTE device.

Section 4 Network Turnup Procedure TRACER 4208 System Manual 40 © 2003 ADTRAN, Inc. 612804208L1-1A

612804208L1-1A © 2003 ADTRAN, Inc. 41USER INTERFACE GUIDEProvides detailed descriptions of all menu options and configuration parameters available for the TRACER 4208.This section of ADTRAN’s TRACER 4208 System Manual is designed for use by network administrators and others who will configure and provision the system. It contains information about navigating the VT100 user interface, configuration information, and menu descriptions.CONTENTSNavigating the Terminal Menu 62Terminal Menu Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Navigating using the Keyboard Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Terminal Menu and System Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63Selecting the Appropriate Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Security Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Menu Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Menu 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64FIGURESFigure 1. Top-Level Terminal Menu Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Figure 2. Alternate Menu View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Figure 3. System Info Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70Figure 4. System Status Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Figure 5. System Config Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Figure 6. System Utility Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Figure 7. View Selftest Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Figure 8. Modules Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102Figure 9. T1/PRI Loopback Test Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109Figure 10. E1/PRA Network Loopback Test Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116Figure 11. T1/PRI Loopback Test Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128Figure 12. T1/PRI Loopback Test Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169Figure 13. HSSI Interface Loopback Test Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171Figure 14. Packet Manager Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190Figure 15. Router Menu (IP Selected). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218Figure 16. Dedicated Maps Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233Figure 17. Circuit Status Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250Figure 18. Dial Plan Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253

Section 5 User Interface Guide TRACER 4208 System Manual 42 © 2003 ADTRAN, Inc. 612804208L1-1A1. NAVIGATING THE TERMINAL MENUThe TRACER 4208 menu system can be accessed with a VT100 compatible terminal that is connected to the RS-232 port located on the back of the unit and set to 9600 bits per second, 8 data bits, 1 stop bit, and no parity. Flow control on the serial interface should be configured to NONE for proper operation. Once a terminal is connected, press <Ctrl + L> to refresh the current screen. If password access has been enabled, the ENTER PASSWORD message displays at the bottom of the TRACER 4208 System Status menu. Terminal Menu WindowThe TRACER 4208 uses a series of menu pages and a single main menu page to access its many features. The main menu page (see Figure 1) provides a link to all available configuration/status pages.Figure 1. Main Menu ScreenAll TRACER 4208 systems are shipped factory default with password protection disabled.After connecting a VT100 terminal to the TRACER 4208, press <Ctrl + L> to redraw the current screen.

TRACER 4208 System Manual Section 5 User Interface Guide612804208L1-1A © 2003 ADTRAN, Inc. 43Navigating using the Keyboard KeysYou can use various keystrokes to move through the terminal menu, to manage a terminal menu session, and to configure the system.Moving Through the MenusSession Management Keystrokes2. TERMINAL MENU AND SYSTEM CONTROLPassword ProtectionThe TRACER 4208 provides optional password protection of the terminal interface. If enabled, a password prompt is presented at power-up, reboot, modem logout, or after ten minutes of inactivity on the terminal. The password is enabled and defined via the system configuration menu.To do this... Press this key...Move up to select items Up ArrowMove down to select items Down ArrowEdit a selected menu item EnterScroll through configuration parameters for a menu item SpacebarLeft/Right ArrowsP or N (Prev/Next)Cancel an edit EscapeReturn to Main Menu page MAccess the TRACER 4208 Status page SAccess the System Configuration Menu CDisplay the TRACER 4208 Link Performance History LAccess the T1 (A through H) Status/Configuration/Loopback Menu 1, 3, 5 ... 15Display the T1 (A through H) Performance History 2, 4, 6 ... 16To do this... Press this key...Log into a session SpacebarRefresh the screenTo save time, only the portion of the screen that has changed is refreshed. <Ctrl + L>All TRACER 4208 systems are shipped factory default with password protection disabled.

Section 5 User Interface Guide TRACER 4208 System Manual 44 © 2003 ADTRAN, Inc. 612804208L1-1A3. MENU DESCRIPTIONSThe remainder of this section describes the TRACER 4208 menus and submenus. >TRACER SYSTEM STATUSFigure 2 shows the TRACER 4208 System Status menu page. The status of major system components for both sides of the TRACER link are displayed, but no configuration can be performed from this view.Figure 2. TRACER 4208 System StatusA. Elapsed TimeThe top of the TRACER 4208 System Status menu page displays the elapsed time the TRACER 4208 system has been operational since the last power reset.B. Contact InformationThe ADTRAN technical Support toll-free contact number is located directly beneath the elapsed time display at the top of the TRACER 4208 System Status menu page.The menu structure of the TRACER 4208 system is depicted below as follows:> MENU PAGE> MENU PAGE > MENU SELECTION> MENU PAGE > MENU SELECTION > SUB-MENUAElapsedTimeBContactInformationFLocalHFrequencyIRx PowerCRF StatusGDT1 StatusERemoteHIRx PowerJTx PowerJTx PowerKNavigation Reminder(Error/AlarmOnly)TracerSTATUSPlanFrequencyPlanTRACERStatusSite Name

TRACER 4208 System Manual Section 5 User Interface Guide612804208L1-1A © 2003 ADTRAN, Inc. 45C. RF StatusA graphical indicator of the TRACER RF links is located beneath the Technical Support contact number. The status of the received radio link is indicated as RF UP or RF DOWN for each direction. This RF status display corresponds to the RF DOWN LED on the front of the unit.D. T1 Status (Error/Alarm Only)A visual status of current errors/alarms on the T1 interfaces (for both the local and remote TRACER systems) is provided on the TRACER 4208 System Status menu page. T1A through T1H displayed in reverse highlight indicates an active error or alarm condition. Individual T1 status pages (accessible from the main menu) provide detailed T1 information.E. Remote TRACER StatusThe right portion of the TRACER 4208 System Status menu page reports the status of the remote TRACER 4208 (the system across the wireless link from the active terminal). If the RF link is down, DATA NOT AVAILABLE is displayed in place of the remote system status information.F. Local TRACER StatusThe left portion of the TRACER 4208 System Status menu page reports the status of the local TRACER 4208 (the system where the active terminal is attached). G. Si t e Nam eThe SITE NAME field provides a user-defined alphanumeric description (up to 25 characters) for the TRACER 4208 system. This field is defined from the TRACER 4208 System Configuration menu page.H. Frequency PlanDisplays the frequency plan (A or B) for the TRACER 4208 unit. For an operational TRACER 4208 system you should have one A and ond B frequency plan.I. Rx PowerDisplays the approximate receiver levels (for both the local and remote units) using a series of symbols (#). The more symbols (#) displayed, the stronger the signal. If the link is down and remote end data is unavailable, DATA NOT AVAILABLE is displayed in place of the symbols (#).J. Tx PowerDisplays the approximate transmitter levels (for both the local and remote units) using a series of symbols (#). The more symbols (#) displayed, the stronger the signal. If the link is down and remote end data is unavailable, DATA NOT AVAILABLE is displayed in place of the symbols (#).K. Navigation RemindersDisplays system navigation reminders. For more details on system navigation, refer to Navigating the Terminal Menu on page 42.

Section 5 User Interface Guide TRACER 4208 System Manual 46 © 2003 ADTRAN, Inc. 612804208L1-1A>MAIN MENUThe TRACER 4208 Main Menu page provides access to all other configuration/status pages. Figure 3 shows the TRACER 4208 Main Menu page.Figure 3. TRACER 4208 Main MenuFrom the keyboard, use the up and down arrow keys to scroll through the available pages, or enter the number or letter of the selected page (to highlight the menu page) and press <Enter>.Press <m> from any menu in the TRACER 4208 VT100 menu structure to access the TRACER 4208 Main Menu page.

TRACER 4208 System Manual Section 5 User Interface Guide612804208L1-1A © 2003 ADTRAN, Inc. 47>TRACER SYSTEM CONFIGURATIONFigure 4 shows the TRACER 4208 System Configuration menu page. System configuration parameters for both the local and remote TRACER 4208 units are available through this menu page.Figure 4. TRACER 4208 System Configuration>TRACER SYSTEM CONFIGURATION > RX POWERDisplays the approximate receiver levels (for both the local and remote units) using a series of symbols (#). The more symbols (#) displayed, the stronger the signal. If the link is down and remote end data is unavailable, DATA NOT AVAILABLE displays in place of the symbols (#). This parameter is display only.>TRACER SYSTEM CONFIGURATION > TX POWERAllows the transmitter levels (for both the local and remote units) to be adjusted. The current transmitter level is displayed using a series of symbols (#). The more symbols (#) displayed, the stronger the signal. If the link is down and remote end data is unavailable, DATA NOT AVAILABLE displays in place of the symbols (#).Press <C> from any menu in the TRACER 4208 VT100 menu structure to access the TRACER System Configuration menu page.Reducing the transmitter power of the remote TRACER 4208 could negatively impact the TRACER RF link.

Section 5 User Interface Guide TRACER 4208 System Manual 48 © 2003 ADTRAN, Inc. 612804208L1-1A>TRACER SYSTEM CONFIGURATION > SITE NAMEProvides a user-defined alphanumeric discription (up to 25 characters) for the TRACER 4208 system.>TRACER SYSTEM CONFIGURATION > RF BANDPLANSets the bandplan for the TRACER 4208. Each channel is divided into three bandplans (1, 2, or 3). Both local and remote TRACER 4208 must be configured with the same bandplan (1, 2, or 3) but different channel plans (Plan A or Plan B). For example, the transmitter at one end of the link will transmit in bandplan 1 of channel A (the lower portion of the spectrum) and receive in bandplan 1 of channel B (the upper portion). Consequently, the receiver at the other end should receive in bandplan 1 of channel A (the lower portion) and transmit in bandplan 1 of channel B (the upper portion). (Refer to Figure 5). The TRACER 4208 comes factory programmed with RF bandplan set to Band 1.Figure 5. 5.8 GHz Bandwidth Division (TRACER 4208)>TRACER SYSTEM CONFIGURATION > MODEM CONTROLConfigures the modem control leads on the RS-232 port (terminal interface located on the rear panel of the unit). Set MODEM CONTROL to ENABLED when connecting the unit to a modem (using a null modem adapter). Setting MODEM CONTROL to DISABLED prevents the TRACER 4208 from monitoring DCD and enables data to be sent to the VT100 continuously. MODEM CONTROL must be set to DISABLED when the VT100 terminal is in use. The TRACER 4208 comes factory programmed with MODEM CONTROL set to DISABLED.>TRACER SYSTEM CONFIGURATION > MODEM CONNECTION (LOGOUT)Causes the TRACER 4208 to de-assert Clear To Send (CTS) and DSR for a time greater than 20 msec. This signals the modem to disconnect the analog connection. Hangup-On-DTR-Drop may need to be explicitly enabled on some modems. If PASSWORD PROTECTION is ENABLED, this menu also causes the unit to close the current session and return to the TRACER System Status menu page and wait for password input.Press <Ctrl+Z> three times from the terminal interface to disable MODEM CONTROL when the modem control leads are active.ChannelA5742725 5787 58505747 5753MHzMBandplan3Bandplan2Bandplan1ChannelB5815 5827 5833Bandplan3Bandplan2Bandplan1

TRACER 4208 System Manual Section 5 User Interface Guide612804208L1-1A © 2003 ADTRAN, Inc. 49>TRACER SYSTEM CONFIGURATION > PASSWORD ENABLEConfigures password protection for the VT100 terminal interface. Password protection for the TRACER 4208 requires password input from the TRACER 4208 System Status menu page when connecting to the unit. When configured for password protection, the TRACER 4208 closes any terminal session that remains inactive for more than 10 minutes. The TRACER 4208 comes factory programmed with PASSWORD ENABLE set to DISABLED. >TRACER SYSTEM CONFIGURATION > PASSWORDSets the password for password protection of the TRACER 4208 VT100 terminal interface. Enter up to 8 alphanumeric characters. The system password is case sensitive.>TRACER SYSTEM CONFIGURATION > PERFORMANCE STATS (CLEAR)Resets all system error counters for the TRACER 4208.>TRACER LINK PERFORMANCE HISTORYFigure 6 shows the TRACER 4208 Link Performance History menu page, which displays detailed error statistics and received signal level for the RF link (from both the local and remote TRACER 4208 units) in 15-minute increments. Figure 6. TRACER Link Performance HistoryThe default password for the TRACER 4208 is tracer.24 Hours7 Days

Section 5 User Interface Guide TRACER 4208 System Manual 50 © 2003 ADTRAN, Inc. 612804208L1-1AThe minimum received signal level (MIN RSL) is represented as a numerical value from 0 to 255 with 0 corresponding to no receive power and 255 corresponding to an extremely strong signal. The minimum received signal level is directly related to RSSI.The error count and received signal level for the most recent 24 hours are recorded and displayed on the right side of the page. The left side of the page displays the 24 hour totals for the most recent 7 days. > T1X STATUS/CONFIGURATION/LOOPBACKFigure 7 shows the T1x Status/Configuration/Loopback menu page, which displays a real-time graphical representation for the T1x link (using data from both the local and remote TRACER 4208 units) is displayed on this page. T1x operational configuration parameters and testing functions are configured from this menu.Figure 7. T1x Status/Configuration/LoopbackPress <N> to view the next 8 hours worth of 15-minute totals and <P> to view the previous 8 hours.Press <L> from any menu in the TRACER 4208 VT100 menu structure to access the TRACER Link Performance History menu page.The following menus for the T1x Staus/Configuration/Loopback and T1x Performance History apply to all eight available T1 interfaces (A through H).

TRACER 4208 System Manual Section 5 User Interface Guide612804208L1-1A © 2003 ADTRAN, Inc. 51>T1X STATUS/CONFIGURATION/LOOPBACK > T1X INTERFACE ALARMSDisplays any active alarms on the T1 link (reported from both the local and remote TRACER 4208 units). These alarms include Red, Blue/AIS, Yellow, LOS, and bipolar violations (BPV). Table 1 breifly describes these alarms. See Section 6, Troubleshooting Guide, for more information on these alarms.>T1X STATUS/CONFIGURATION/LOOPBACK > T1X LINE BUILD OUTConfigures the T1 for the appropriate line buildout, based on the distance to the T1 equipment. >T1X STATUS/CONFIGURATION/LOOPBACK > ALARM REPORTINGDetermines whether the TRACER 4208 unit will report active alarms. If set to DISABLED, no alarms will be displayed on this menu page. The ALARM REPORTING parameter is independently configured for the local and remote TRACER 4208 units. When set to DISABLED, the front panel LED alarms are also disabled (OFF).>T1X STATUS/CONFIGURATION/LOOPBACK > SIGNALINGConfigures the framing format for the T1 link for both the local and remote TRACER 4208 units. The TRACER 4208 transports T1 data across the link (as long as the T1 signal is properly timed). Configure the framing format (using the SIGNALING menu) to enable the TRACER 4208 to monitor incoming framing error events and indicate problems with the attached metallic service. The TRACER 4208 supports both ESF and D4 framing formats.>T1X STATUS/CONFIGURATION/LOOPBACK > LINE CODESets the line coding for the T1 link. The TRACER 4208 supports B8ZS and AMI line coding.>T1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATEControls the loop status of the T1 link. Activates/deactivates loopback conditions for testing purposes.>T1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATE > NORMALDefines the T1 link as normal data transport mode - there are no active loopbacks.Table 1. T1 Interface AlarmsRED Activates when a local facility failure occurs.Blue/AIS Activates when an incoming remote alarm is received from a connected T1 device. An AIS signal is an unframed All One signal that replaces the normal traffic signalYEL Activates when an incoming remote alarm is received from the T1 device indicating that a failure has occurred in the received direction.LOS Activates when no T1 signal is present from the connected T1 equipment. LOS is activated after receiving 192 consecutive zeros.BPV Activates when the incoming T1 stream presents bipolar violations (BPVs).

Section 5 User Interface Guide TRACER 4208 System Manual 52 © 2003 ADTRAN, Inc. 612804208L1-1A>T1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATE > LINKActivates a loopback at the TRACER 4208 T1 framer towards the wireless link (see Figure 8). Use the LINK loopback to test data path integrity from one unit across the wireless link.Figure 8. T1 Link Loopback>T1X STATUS/CONFIGURATION/LOOPBACK > LOOP/NORMAL STATE > LINEActivates a loopback at the TRACER 4208 T1 framer towards the locally connected T1 equipment (see Figure 9). Use the LINE loopback to test data path integrity from the TRACER 4208 unit to the T1 equipment.Figure 9. T1 Line Loopback>T1X PERFORMANCE HISTORYFigure 10 shows the T1x Performance History menu page, which displays detailed error statistics for the T1 link (from both the local and remote TRACER 4208 units) in 15-minute increments. Figure 10. T1x Link Performance History24 Hours7 Days

TRACER 4208 System Manual Section 5 User Interface Guide612804208L1-1A © 2003 ADTRAN, Inc. 53T1 performance data is presented as Errored Seconds (ES) and Severely Errored Seconds (SES) on the T1 link. The following events qualify as an ES–AIS, LOS or LOF Alarm Second, a single bipolar violation (BPV), excessive zero event, or a single parity bit. An SES is caused by an AIS, LOS or LOF Alarm Second, excessive BPVs, or framed parity bit errors causing a line bit error rate (BER) of 10-6.The error count for the most recent 24 hours are recorded and displayed on the right side of the page. The left side of the page displays the 24 hour totals for the most recent 7 days.Press <N> to view the next 8 hours worth of 15-minute totals and <P> to view the previous 8 hours.Press <2> from any menu in the TRACER 4208 VT100 menu structure to access the T1x Link Performance History menu page.

Section 5 User Interface Guide TRACER 4208 System Manual 54 © 2003 ADTRAN, Inc. 612804208L1-1A

612804208L1-1A © 2003 ADTRAN, Inc. 55TROUBLESHOOTING GUIDEProvides helpful information for troubleshooting common configuration problems for the TRACER 4208.CONTENTSOverview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56PWR LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56TST LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56RF DOWN LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56RF LOW LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57T1 Interface Alarm LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57RF Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Step-by-Step Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Installing/Troubleshooting the TRACER Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Installing/Configuring T1 Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Section 6 Troubleshooting Guide TRACER 4208 System Manual 56 © 2003 ADTRAN, Inc. 612804208L1-1A1. OVERVIEWThis troubleshooting guide provides recommended actions for various conditions of the TRACER 4208 system. The status LEDs (located on the front panel of the unit) provide information to help determine the necessary troubleshooting action. Recommended actions for resolving possible status LED indicators are contained in this guide.2. LED INDICATORSPWR LEDIf the PWR LED is not ON and solid green, it is an indicator that the TRACER 4208 is not receiving adequate DC power. Recommended Actions:1. Verify that the power source is delivering between 21 and 60 VDC.2. Check the polarity of the power connection (referenced to ground) of both the TRACER 4208 unit and the power source.3. Check the internal fuse. The fuse is accessed from the rear panel of the unit. If this fuse is open, replace with a 1 A, 250 V (2-inch) slow-blo fuse.TST LEDThe TST LED will remain ON (solid amber) during power-up to indicate a self-test is in progress. If the TST LED is blinking or remains ON after 10 seconds, this indicates that the TRACER 4208 unit has failed the self-test. This is an internal failure, and ADTRAN technical support should be contacted.RF DOWN LEDIf the RF DOWN LED is ON (solid red), it is an indicator that there is a problem with the RF link to the TRACER 4208.Recommended Actions:1. Check the RF coaxial cable connection.2. Measure the RSSI voltage. If the signal is acceptable (> 2.0 VDC at RSSI test point), go to Step 6.3. Verify that one end of the link is configured as Plan A and the other end as Plan B, and that both ends have the same bandplan Number (ex. A1 and B1).4. Verify that the antenna polarization is the same at both ends of the RF signal transmit and receive path.5. Verify the RF signal path is clear.6. Check for possible interference at both ends of the link. If necessary, change polarization and/or bandplans at both ends.

TRACER 4208 System Manual Section 6 Troubleshooting Guide612804208L1-1A © 2003 ADTRAN, Inc. 57RF LOW LEDIf the RF LOW LED is ON (solid red), it is an indicator that the received signal is within 10 dB (approximately) of the minimum operable signal. This condition is typically indicative of a path problem.Recommended Actions:1. Verify the far-end transmitter power setting is the value that the link planning budget allows.2. Check all coaxial cable connectors for solid connections. Check for water and corrosion around any of the connectors. If water is apparent in the coaxial connectors, replace the coaxial cable and the connectors, making sure to properly weatherproof the replacements.3. Verify the RF signal path by verifying the antenna alignment.4. Check the integrity of the cable plant.5. Check the integrity of lightning arrestors.T1 Interface Alarm LEDsIf the ALARM LED is ON (solid red), it is an indication that the TRACER 4208 is detecting an active T1 alarm. To identify the T1 interface in alarm and the specific alarm present, display the T1(X) STATUS screens and check the T1(X) INTERFACE ALARMS field.Recommended Actions:1. Display the T1(X) STATUS screen and check the T1(X) INTERFACE ALARM field to identify the active alarm. 2. Follow the steps below for the appropriate alarm.LOS Alarm (Red Alarm)LOS ALARM is an indication that the TRACER 4208 may be unable to detect a viable T1 received signal from the connected T1 equipment. This error may be due to a degraded signal or no signal, or may be caused by improper framing.Recommended Actions:1. Verify that the T1 cable is connected to the T1 interface on the TRACER 4208.2. Verify the connections at the opposite end of the T1 cable.3. Verify that the framing mode (D4 or ESF) is the same for both the TRACER 4208 and the T1 equipment.Yellow AlarmA Yellow Alarm is generated by the attached equipment. When the attached equipment’s T1 interface is in Red Alarm, the TRACER 4208 generates a Yellow Alarm.Recommended Actions:1.Follow the troubleshooting steps for Red Alarm, but do so at the attached equipment.Blue Alarm A remote alarm (alarm indication signal or AIS) is generated by the attached equipment. The root cause must be determined at the attached equipment. A typical cause of a blue alarm is a lack of input to a CSU.Recommended Actions:1.Verify the input to any attached data equipment.

$TRACER 4208 System Manual Section 6 Troubleshooting Guide612804208L1-1A © 2003 ADTRAN, Inc. 594. Attach the RF coaxial cables to be used in the permanent installation to the N-type connectors on the back of the TRACER 4208 unit. Attach the other end of the coaxial cable(s) to an RF power meter or spectrum analyzer, if either is available. The power measured by the meter/analyzer will be the RF power available at the input of the antenna. The TRACER 4208 unit is programmed at the factory to output approximately 100 mW (20 dBm) of RF power. The actual power level measured by the meter/analyzer will be less than 100 mW due to RF losses through the coaxial cable, and is a function of the cable type and length being used. In any event, the power level at the output of the coaxial cable should be a significant fraction of 100 mW. A power meter/analyzer reading that is not on the order of at least tens-of-milliwatts could be an indication of any combination of either unsuitable RF, faulty, or unreasonably long coaxial cable.5. Resolve all RF coaxial cabling errors before proceeding.6. Attach the RF coaxial cables to a high-quality attenuator, if possible. If you do not have an attenuator, attach the coaxial cables to the antennas to be used in the permanent installation. If the installation antennas are not available, small, inexpensive dipole or patch antennas can be used for verification purposes. If an adjustable attenuator is being used, dial in the amount of attenuation that corresponds to the path loss value expected for the microwave link in which the TRACER hardware will be installed. The path loss value can be calculated from a knowledge of the path length, or provided by a path study. Remember to subtract both antenna gain values from the attenuator level if these values have not already be accounted for.7. After setting up the RF pieces, examine the RF DOWN LED on the front panel of each TRACER 4208 unit. If the RF DOWN LED is illuminated (red), the corresponding TRACER 4208 is not receiving a suitable RF signal from the other TRACER 4208 unit. In this case, the receiving TRACER 4208 is either receiving a very weak signal, or no signal at all. If the RF DOWN LED is not illuminated, then the TRACER 4208 units are receiving a suitable RF signal. Suitable RF power levels for low error rate communication will range from -30 dBm to -86 dBm measured at the N-type connector input on the TRACER 4208 unit.8. Resolve any signal level issues before proceeding.9. Examine the RF LOW LED on the front panel of each TRACER 4208. If this LED is illuminated, then the TRACER 4208 is receiving a relatively weak signal; however, if the RF DOWN LED is not illuminated, then the received signal is being suitably processed by the TRACER 4208 system. If you are receiving a weak signal (RF LOW is ON), please verify that the weak signal is not being caused by a faulty cable, an insufficiently tightened cable, or some other installation-related problem. Also, make sure an unreasonably large attenuation value has not been selected if you are using an attenuator on a workbench setup. Use the tables in Section 2, Microwave Path Engineering Basics, of this manual to select the proper free-space attenuation value (in dB) based on the estimated length of the microwave path. Remember to subtract both antenna gains (local and remote) from the attenuator setting.10. Command a link loopback in one TRACER 4208 unit and run a test pattern from the connected T1 equipment. This will verify the data path between the T1 equipment and the TRACER 4208 unit. External pattern generators are required to test data path integrity. A T1 BERT tester is suggested.$

ADTRAN TRC4208 TRACER 4208 User Manual 612804208L1 1A

Adtran TRACER 4208 612804208L1 1A

Manual

Navigation menu

Namespaces

Views

Navigation