Advanced Control Technologies 0738-02 Wireless Duplex Receptacle User Manual ZRR150 S300 R2 1 instr p65

Advanced Control Technologies, Inc. Wireless Duplex Receptacle ZRR150 S300 R2 1 instr p65

Contents

Manual - (ZRR150 Series)

Z-Wave ZRR150 Instructions, Series 300, Rel. 2.1010510HomeProby ADVANCED CONTROL TECHNOLOGIES, INC.0738-021ZRR150HomeProRF Home AutomationZRR150 DUPLEX RECEPTACLEThe ZRR150 Duplex Receptacle is a component of the HomePro lighting control system. Wire the Duplex Receptaclein place of a standard receptacle according to the diagram above and program from the Wireless Controller to operateloads. Inclusion of this Receptacle on the ZTH100 Wireless Controller menu allows remote ON/OFF control of loadsconnected to the controlled outlet. The other outlet remains powered all the time.This ZRR150 Duplex Receptacle is designed to work with other Z-Wave enabled devices. Z-Wave nodes of othertypes can be included in the system and will also act as repeaters if they support this function of repeating the signalreceived, to other modules in the system.This product supports 40Kbps data transmission. This product can also be used for networking support insystems that stream metadata. An example might include transmission of information from audio devices such assong title, artist, and album information to various displays around the home.As part of a Z-Wave network, the ZRR150 will also act as a wireless repeater to insure that commands intended foranother device in the network are received. This is useful when the device would otherwise be out of the radio rangeof the wireless controller.There are no field repairable assemblies on this unit. It is covered by a one year limited warranty. If service is needed,the unit must be returned where purchased.DANGER! SHOCK HAZARD. Read and understand these instructions before installing. This device is intended forinstallation in accordance with the National Electric code and local regulations in the United States, or the CanadianElectrical Code and local regulations in Canada. It is recommended that a qualified electrician perform this installation.Make sure the total load controlled does not exceed 1800 watts. For indoor use only. Retain instructions for futureuse.INSTALLATIONWire this Receptacle in place of a current receptacle according to the diagram above. Use copper wire only, or theequivalent. See the ZTH100 Wireless Controller operating instructions to add this module under the command of theWireless Controller.Note: This module must be “Includedin the Network” only where it will bepermanently installed. The properoperation of this node in the meshnetwork is dependent on it knowing itslocation with respect to other nodes.You cannot “test bench” configurethis module, then install.Controlled OutletAlways Powered OutletRadio Frequency Controlled, 120 VAC, 15A,Duplex Receptacle, Series 300, Rel. 2.1• This product supports Zensor Net Beam technology.
Z-Wave ZRR150 Instructions, Series 300 Rel. 2.1010510HomeProby ADVANCED CONTROL TECHNOLOGIES, INC.0738-022INCLUDING ZRR150 TO THE NETWORKSTEP 1.. Prepare the Controller to include a unit to the network, by selecting “Groups” and “Add Unit to Group”(method of adding a node to the network). Refer to controller instructions.STEP 2. The ZRR150 must be in its permanently installed location. Tap the button on the face of theZRR150 once when your controller indicates “Press Button on Unit”.STEP 3. You should see an indication on your Controller that the “Device was Included” in the network.NOTE: If you have trouble adding the ZRR150 to a group it may be that the Home ID and Node IDwere not cleared from it after testing. You must first “Reset Unit” with your controller to remove itfrom the network. If using the ZTH100 select “Setup” and scroll to “Reset Unit”Although adding it to a group includes it in the network, removing it from a group does not remove it from thenetwork. If removed from a group, it functions as a repeater only. “Reset Unit” removes it from the network.Receptacle ConfigurationThe ZRR150 Receptacle controls the ON and OFF of a load connected to the controlled outlet (see diagram onpage one for identification). The other outlet remains powered all the time. A button on the face of the receptacleis used to add the module to the wireless network and be controlled from the wireless controller. With the WirelessController, the ZRR150 Receptacle can be turned ON and OFF remotely, and can be included in groups thatoperate at the same time (a group can also be a single module), and in scenes that set a lighting mood.Local ON and OFFWhen the button on the face of the ZRR150 is pressed, the power to the controlled outlet will turn on. When thebutton is pressed again, the the controlled outlet will turn off.Child ProtectionThe ZRR150 controlled outlet can be set in a child protect mode by the Wireless Controller. When this mode isactive, a user will have to press the button on the face 3 times rapidly to activate the attached load. The moduleoperates normally when controlled by the Wireless Controller..Other functionsThe button on the face of the ZRR150 Receptacle can be used to carry out inclusion (add to a group), association(operate simultaneously with other nodes), exclusion (remove from group) or reset (remove from network). Thisis described in more detail in the Advanced Wireless Controller instructions on our web site.The ZRR150 has a blue indicator LED. This LED will turn on when the controlled outlet is on and will turn off whenthe controlled outlet is off. However, its behavior can be configured as a “night light” (LED ON when the controlledoutlet is off). See Configuration section below on how to do it.ADVANCED OPERATIONConfigurationThe ZRR150 supports the Configuration command.The ZRR150 has some features that can be configured (If your controller supports it).The ZRR150 can be configured to operate slightly differently than how it works when you first install it. You canuse a HomePro ZTH100 Wireless Controller to send Configuration commands (refer to the Setup Menu,Configuration section of the ZTH100 instructions). Using the Configuration command you can configure thefollowing:Nightlight:Set this parameter to 0 to have the blue indicator LED show state of controlled outlet (indicator ON = outlet ON).Set this parameter to 1 to have indicator show the opposite state of controlled outlet (indicator ON = outlet OFF)• Configuration Parameter No 3:• Length: 1 Byte• Valid Values: 0 or 1 (Default: 0)
Z-Wave ZRR150 Instructions, Series 300, Rel. 2.1010510HomeProby ADVANCED CONTROL TECHNOLOGIES, INC.0738-023SPECIFICATIONSPower 120 VAC, 60 HzMaximum Load Resistive: 15 amps (1800 watts) maximum, 120 VACSignal (Frequency) 908.42 MHzRange Up to 100 feet line of sight between the Wireless Controllerand/or the closest HomePro ModuleWARRANTYFor warranty and general product information visit our web site at www.act-solutions.comABOUT ZRR150’S CERTIFICATIONThe ZRR150 is certified to comply with applicable FCC and ICrules and regulations governing RF and EMI emissions.This device complies with part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) This device may not causeharmful interference, and (2) This device must accept any interfer-ence received, including interference that may cause undesiredoperation.FCC NOTICENote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions may cause harmful interference to radio communications. However, there is no guaran-tee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authorityto operate the equipment.IC NOTICEThis Class B digital apparatus complies with Canadian ICES-003Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this devicemust accept any interference, including interference that may cause undesired operation of the device. Z-Wave® is a registered trademark of Zensys, Inc. and/or its subsidiaries.

Navigation menu