Apex Digital Dvd Player Lad 703 Users Manual AD703

LAD-703 to the manual eaef0803-441e-44b1-8074-277ddf54d437

2015-01-21

: Apex-Digital Apex-Digital-Apex-Digital-Dvd-Player-Lad-703-Users-Manual-236362 apex-digital-apex-digital-dvd-player-lad-703-users-manual-236362 apex-digital pdf

Open the PDF directly: View PDF .
Page Count: 46

APEX DIGITAL

AD-703

Safety Precautions

The lightning flash with a arrowhead symbol within an equilateral triangle is

intended to alert the user to the presence of uninsulated "dangerous

voltage" within the product's enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the

user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

WARNING: DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE, DUE TO THE HIGH RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT OPEN THE CABINET DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE

ENCLOSURE. ONLY QUALIFIED SERVICE PERSONNEL SHOULD ATTEMPT THIS.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, AND

FULLY INSERT.

ATTENTION: POUR EVITER LES CHOCS ELECTRIQUE, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE

DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOUD.

CAUTION: This Digital Video Disc Player employs a Laser System. To prevent direct exposure to the laser beam, do not

try to open the enclosure. Visible laser radiation when open and interlocks defeated.

The use of control adjustments or the performance of procedures other than those specified may result in

hazardous radiation exposure.

DO NOT STARE INTO BEAM.

To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference.

Should the unit require maintenance, contact an authorized service location, or contact APEX Digital Inc. Only

qualified service personnel should remove the cover.

FCC NOTICE:This equipment has been tested and found to comply with the limits for a Class B digital device. Pursuant with

the FCC Rules, Part 15. These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

WARNING:Changes or modifications made to this equipment, not expressly approved by APEX or parties authorized by

APEX will void all the manufacture warranties.

THE REGION CODE FOR THE UNIT IS 1.

Since it is very usual for DVD movies to be released at different times in different regions of the world, all

players have region codes and disks can have an optional region code. If you load a disk of a different

region code to your player, you will see the region code notice on the screen. The disk will not play, and

should be unloaded.

For Customer Use:

In spaces provided below, record the Model and Serial No. located on the rear panel of your DVD video player.

Model No. Serial No.

Retain this information for future reference.

CLASS 1

LASER PRODUCT

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS RISQUE DE CHOC ELECTRIQUE NE

PAS OUVRIR

WARNING: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PART INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION:

PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS OWNER’S

MANUAL AND THOSE MARKED ON THE UNIT. PLEASE KEEP THIS MANUAL FOR FUTURE USE.

This product was designed and manufactured to meet strict quality and safety standards. The safeguards incorporated

in this unit will protect you if you observe the following procedures for installation, use, and service. There are, however,

some installation and operation precautions which you should be aware of.

2APEX DIGITAL AD-703

1. READ THE OWNER’SMANUAL -Follow all the operating

and installation instructions.

2. RETAIN INSTRUCTIONS -The safety and operating

instructions should be retained for future use.

3. PAY ATTENTION TO WARNINGS -All warnings on the

appliances and in the operating instructions should

be followed.

4. FOLLOW INSTRUCTIONS -Follow all operating

instructions to achieve optimal use.

5. POWER SOURCES -This product should only be

operated from the type of power source indicated on

the label.

6. HEAT -This unit should be situated away from heat

sources, such as amplifiers, radiators, stoves or any

other units producing heat.

7. WATER AND MOISTURE -Do not use this unit near

water, for example: near the kitchen sink, a bath tub,

washbowl, laundry tub, swimming pool, or in a wet

basement.

8. CLEANING -Unplug the unit from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol

cleaners directly on the unit. Use a damp cloth for

cleaning.

9. CARTS AND STANDS -The unit and cart combination

should be moved with care. Quick stops, excessive

force and uneven surfaces may cause the unit and cart

combination to overturn. The unit should be used only

with a cart or stand recommended by the manufacturer.

10. POWER-CORD PROTECTION - Power-supply cords

should be routed so that they are not likely to be walked

on or pinched by items places upon or against them.

11. OVERLOADING -Do not overload wall outlet, or

extension cords. This can result in a risk of fire or

electrical shock.

12. DISC TRAY - Keep your fingers well clear of the disc

tray as it is closing. It may cause serious personal

injury,

or do damage to the machine.

13. WEIGHT - Do not place a heavy object (amplifier,

receiver) on your DVD player. The object may fall,

causing serious personal injury or death.

14. OBJECT AND LIQUID ENTRY - Care should be taken so

Important Safety Instructions

APEX DIGITAL

AD-703

that objects do not fall and liquids are not spilled into

the units openings. Such situations could result in fire

or electrical shock.

15. NON-USE PERIODS - The power cord of the unit

should be unplugged, when not in use for a long time.

16. DISC - Do not use a deformed, cracked, or heavily

scratched disc. Using these disc will limit your viewing

pleasure, and/or may damage the internal workings of

your machine.

17. LIGHTING AND POWER SURGES - Use a power strip to

help eliminate surges and spikes caused by lighting and

static electric charges.

18. POLARIZATION OR GROUNDING - Precautions should be

taken so that the polarization or grounding means of a

unit is not defeated. To prevent electric shock match

the wide blade of the plug to the wide slot of the outlet

and fully insert. If the wide blade does not match up

with the outlet try reversing the plug.

19. SERVICING - Do not attempt to service this unit

yourself. Only qualified APEX service technicians

should work on your DVD Player.

20. DAMAGE REQUIRING SERVICE -The unit should be

serviced by qualified APEX authorized specialist when:

A. The unit does not appear to operate normally or

exhibits a marked change in performance.

B. When the power supply cord or plug is damaged.

C. If objects have fallen, or liquid has been spilled into

the unit.

D. If the unit has been exposed to water or rain.

E. If the unit has been dropped or damaged in any way.

21. SAFETY CHECK -Ask the service technician to

perform safety checks upon completion of the unit.

22. WALL AND CEILING MOUNTING -The unit should be

mounted to a wall or ceiling only as recommended by

the manufacturer.

Continued

Important Safety Instructions

4APEX DIGITAL AD-703

Introduction

Your DVD video player is a player for digital video discs

conforming to the universal DVD video standard. With it, you will

be able to enjoy full-length movies with true cinema picture quality,

and stereo or multi-channel sound (depending on the disc, and on

your playback setup). The unique features of this DVD video, such

as selection of sound track and subtitle languages, and of different

camera angles (again depending on the disc), are all included.

What’s more, Parental Control lets you decide which discs your

children will be able to see.

You will find your player remarkably easy to use, by way of the On-

Screen Display (Setup Menu) and player display, in combination

with the remote control.

UNPACKING

When shipping the DVD video player, the original shipping carton and packing comes in handy. For

maximum protection, repack the unit as it was originally packed at the factory.

First check and identify the contents of your DVD video players package, as listed below:

- DVD video player

- Remote control handset with separately packed batteries

- Power cable

- RCA cables (3) (1 yellow, 1 red, and 1 white)

- Owner’s manual

- Size AAA batteries (2)

If any item should be damaged or missing, please inform your supplier without delay.

Keep the packaging materials, you may need them to transport your player in the future.

WHERE TO LOCATE YOUR DVD

A. Place the unit on a firm, flat surface.

B. When you place this DVD video player near a radio, or VCR, the playback picture may become poor

and/or distorted. In this situation, move the DVD video player away from the other units.

C. Keep away from direct sunlight & domestic heating equipment.

D. If placed in a cabinet, please allow at least 2.5 cm (1 inch) of free space all around the player for

proper ventilation.

TO OBTAIN A CLEAR PICTURE

The DVD video player is a high technology, precision device. If the optical pick-up lens and disc drive parts

are dirty or worn down, the picture quality becomes poor. To obtain a clear picture, we recommend regular

inspection and maintenance (cleaning or parts replacement) every 1,000 hours of use depending on the

operating environment. For details, contact your nearest dealer.

APEX DIGITAL

AD-703

Table of Contents

Safety Precautions ........................... 1

Important Safety Instructions ........... 2 - 3

Introduction ........................................ 4

Identification of Controls .................... 6

DVD Display ....................................... 7

Remote Control .................................. 8 - 9

Connecting to a TV using a RF Modulator

........................................................ 10 - 11

Preparation before Operation ........... 12 - 15

What is MP3 and VCD? ..................... 16

Basic Operation ................................. 17 - 20

Playing Disc in Various Ways ........... 21 - 30

MP3 Operations ................................ 31 - 33

Karaoke ............................................. 33

Function Settings .............................. 34 - 41

Notes on Discs .................................. 42

Specifications ..................................... 43

Before Calling Service Personnel ...... 44

Memo ................................................ 45

Limited Warranty ................................ 46

6APEX DIGITAL AD-703

Identification of Controls

FRONT PANEL

REAR PANEL

1 6 11

2 3 4 5 7

1POWER ON/OFF

2MIC 1

3MIC 2

4MIC LEVEL

5ECHO LEVEL

6DVD DISPLAY

7DISC LOADING TRAY

8PLAY

9PAUSE

10 STOP

11 OPEN/CLOSE

12 SKIP REVERSE

13 SKIP FORWARD

14 DIRECT PLAY OR DISC EXCHANGER

12 13 14

8 9

1POWER SUPPLY CORD

25.1 CHANNEL AUDIO OUT

3MIXED AUDIO OUT

4VIDEO OUT

5S-VIDEO OUT

6COAXIAL OUT

3 4 5

APEX DIGITAL

AD-703

DVD Display

• Other indicators

When playing back the

same title, chapter or

track repeatedly.

When playback is paused.

When playing back a

specific segment

repeatedly. (A-B repeat)

During memory playback.

During shuffle playback.

When playing back the entire

disc repeatedly.

When the camera angle can

be changed.

The indicators vary depending on the kinds of discs you play.

Push the DIMMER button, the brightness of the display is

reduced by half; push it once more, the display becomes

dark. Push the button again, the display resumes brightness.

Play

indicator

SUPER-VCD VCD

and CD indicator

PBC

indicator

Pause

indicator Title

indicator

Remain

indicator

Chapter/track

indicator

Lock

indicator

Program

indicator

Angle

indicator

Dolby Digital

indicator

Repeat play

indicator

Track

calendar

DVD

indicator Title/chapter/track

indicator

Hour

indicator Minute

indicator Second

indicator

Disc recording

indicator

Resume

indicator

8APEX DIGITAL AD-703

17. DIGEST

18. TIME SEARCH

19. RESUME

20. REMAIN

21. ZOOM

22. SLOW PLAY

23. PAUSE/STEP

24. MENU

25. RETURN

26. REPEAT

27. A-B REPEAT

28. AUDIO MODE

29. SUBTITLE

30. MUTE ( )

31. LANGUAGE ( )

Remote Control

1. OSD

2. DIMMER

3. NUMBER BUTTONS

4. SEARCH

5. SETUP

6. TITLE

7. PLAY

8. PREV/NEXT

9. STOP

10. DIRECTIONS

11. SYSTEM

12. KEY CONTROL

13. VOLUME

14. DISK SKIP

15. ANGLE ( )

16. PLAY MODE

THE INSTRUCTIONS IN THIS MANUAL DESCRIBE

THE FUNCTIONS ON THE REMOTE CONTROL.

Press , or anytime on the front panel or

on the remote control unit, you can switch the disc

inside the 3 disc changer.

1 2 3

NOTICE

A few seconds is needed during switching the disc inside the 3 disc changer.

Press EXCHANGE on the front panel, you can

change the rest of two discs and it will not affect

the disc that is currently playback. After you finish

changing the two discs, press EXCHANGE again

and the loader will close and store that two discs

inside the 3 disc changer.

APEX DIGITAL

AD-703

Remote Control Continued

1 2 3

Open the battery cover.

OPERATING WITH THE REMOTE CONTROL

Operating DVD video player with the remote control.

The remote control must point at the remote sensor, in order for the

DVD player to function correctly. Make sure there is no barrier

between them.

Distance: Maximum of 5 m from the front of the remote sensor.

Angle: Approximately 30º from each direction.

*Please do not place the remote sensor towards any light source such as direct

sunlight or illumination. The DVD video player will malfunction, if you do so.

Insert two batteries (AAA size).

Make sure to match the + and - on the

batteries to the marks inside the battery

compartment.

Close the battery cover.

NOTICE (BATTERIES)

PREPARING THE REMOTE CONTROL

To operate the DVD video player, you must first place the batteries into the remote control.

FOLLOW INSTRUCTIONS BELOW BECAUSE INCORRECT USE OF BATTERIES MIGHT CAUSE THEM TO LEAK OR CORRODE.

• Do not place the batteries in the wrong direction.

• It is dangerous to charge/heat/open or short-circuit the batteries.

• Do not leave dead batteries or mix old/new batteries in the remote control.

• When not using the remote control for a long duration of time, remove the batteries.

• When difficulties occur, with the remote control, or if the operating range becomes reduced, then replace the batteries.

• If leakage from the battery occurs, wipe the battery liquid from the battery compartment, then replace the batteries.

• With normal usage the batteries should last one year.

NOTICE (REMOTE CONTROL)

• The remote control should be aimed directly towards the remote sensor of the DVD video player.

• Avoid dropping the remote control.

• Avoid spilling any liquids and/or extreme heat.

APEX DIGITAL

AD-703

Connecting to a TV using a RF Modulator

RF-Modulator

Your TV (Back)

VTo TVAntennaRL

UHF/Antenna IN

Coaxial

Your VCR (Back)

UHF/Antenna OUT

Coaxial

COAXIAL

VIDEO OUT

AUDIO OUT

DVD (Back)

TV / Video Input

Conntection

TV /Audio Input

Conntection

(R)

(L)

(V)

Connection 1

Figure 1

Connecting the TV to the DVD through the

VCR

Note: Many VCRs will distort the picture of a DVD

player. This is NOT a malfunction of the DVD player

or VCR. All DVD manufacturers are required to

install macrovision copyright ciruritry to prevent

copying via VCR. This is what causes the distortion.

1) Connect the three-terminal composite video

cable to the back of your Apex DVD player. This

cable has three prongs, one each in yellow, red,

and white. The yellow prong will go into the jack

labeled "Video Out"; the white prong will go into the

jack labeled "Front-L"; the

red prong will go into the jack labeled

"Front-R".

2) Connect the opposite end of the composite-video

cable into the back of the RF modulator. Make sure

to match up the colors correctly.

3) Connect a coaxial cable from the "Antenna Out"

jack on the back of your VCR to the "Antenna" jack

on the RF modulator. The coaxial cable is the one-

wire, metal-ended type that you screw onto the

VCR.

4) Connect a coaxial cable from the "To TV" jack on

the RF modulator to the jack on the back of your

TV.

Many older televisions do not have the newer component-video, composite-video, or s-video connections that

optimize DVD technology. While it would be advised to purchase a newer television in order to take full advantage of

the digital quality of DVD’s, it is possible to connect an older television to a DVD player. This connection requires a

device called an RF modulator.

First, it is necessary to ascertain whether or not your TV needs a RF modulator. Look at the back of your TV. If you

see three input connectors lined up in a row, in the colors of yellow, red, and white, then you will not need an RF

modulator. If you see a connector labeled "s-video", then you will not need an RF modulator. If you do not have either

of these connectors, then you will need to purchase an RF modulator from the store where you purchased your Apex

Digital DVD player or other home electronics retailers.

Older televisions use a coaxial connection, which combines all of the video signal from an exterior source into a

single line. This line is then translated by your TV into the picture you see. The RF modulator combines the output

signals from the DVD player, or any other device, into the coaxial connection for use by your television.

Below are written and pictoral instructions on the proper way to connect an RF modulator to your Apex DVD player

and your TV.

Note: Not all RF Modulators are compatible

with APEX Digital players. Please see our

website for recommendations.

5) Make sure your TV is set to the appropriate

channel before using your DVD player. In most cases,

this is channel 3 or 4.

APEX DIGITAL

AD-703

Connecting to a TV using a RF Modulator

COAXIAL

VIDEO OUT

AUDIO OUT

RF-Modulator

Your TV (Back)

(Back)

TV / Video Input

Conntection

TV /Audio Input

Conntection

VTo TV AntennaRL

(R)

(L)

(V)

To your Cable/Satelite connection

(V)

UHF/Antenna IN

Coaxial

Your Cable/Satelite Box

INOUT IN

OUT

Your VCR (Back)

UHF/Antenna OUT

Coaxial

Figure 3

Connection 3

Connecting the TV , DVD, VCR, and Cable

or Satelite Box

1) Connect the three-terminal composite video

cable to the back of your Apex DVD player. This

cable has three prongs, one each in yellow, red,

and white. The yellow prong will go into the jack

labeled "Video Out"; the white prong will go into

the jack labeled "Front-L"; the red prong will go

into the jack labeled "Front-R".

2) Connect the opposite end of the composite-

video cable into the back of the RF modulator.

Make sure to match up the colors correctly.

3) Connect a coaxial cable from the "Antenna

Out" jack on the back of your cable or satellite

receiver to the "Antenna In" jack on the back of

your VCR. The coaxial cable is the one-wire,

metal-ended type that you screw onto the VCR.

4) Connect a coaxial cable from the "Antenna

Out" jack on the back of your VCR to the

"Antenna" jack on the RF modulator.

5) Connect a coaxial cable from the "To TV" jack

RF-Modulator

Your TV (Back)

VTo TV AntennaRL

To your Cable/Satelite connection

UHF/Antenna IN

Coaxial

Your Cable/Satelite Box

INOUT

COAXIAL

VIDEO OUT

AUDIO OUT

DVD (Back)

TV / Video Input

Conntection

TV /Audio Input

Conntection

(R)

(L)

(V)

Figure 2

Connection 2

Connecting the TV to the DVD through the

Cable or Satelite Box

1) Connect the three-terminal composite video

cable to the back of your Apex DVD player. This

cable has three prongs, one each in yellow, red,

and white. The yellow prong will go into the jack

labeled "Video Out"; the white prong will go into

the jack labeled "Front-L"; the red prong will go

into the jack labeled "Front-R".

2) Connect the opposite end of the composite-

video cable into the back of the RF modulator.

Make sure to match up the colors correctly.

3) Connect a coaxial cable from the "Antenna

Out" jack on the back of your Cable or Satellite

receiver to the "Antenna" jack on the RF

modulator. The coaxial cable is the one-wire,

metal-ended type that you screw onto the VCR.

Continued

4) Connect a coaxial cable from the "To TV" jack on the RF modulator

to the jack on the back of your TV.

5) Make sure your TV is set to the appropriate channel before using

your DVD player. In most cases, this is channel 3 or 4.

on the RF modulator to the jack on

the back of your TV.

6) Make sure your TV is set to the

appropriate channel before using

your DVD player. In most cases, this

is channel 3 or 4. Also make sure

that the VCR is set to the

appropriate channel, as well. This

selector is usually on the back of

your VCR. Consult your VCR

manual for further information.

12 APEX DIGITAL AD-703

1. If the TV has S-VIDEO input, please connect the unit and the TV with S-VIDEO cord (not supplied).

You do not have to connect it to VIDEO. S-VIDEO will ensure clearer image.

2. You have to set the unit according to the TV to be connected.

• If the system of the TV is PAL, push SYSTEM and select PAL.

• If the system of the TV is NTSC, push SYSTEM and select NTSC. (NTSC is American standard.)

• If the system of the TV is AUTO (multi-system), push SYSTEM and select AUTO.

• Connect the unit to a wide-screen TV. Set the “TV DISPLAY” to “16:9 WIDE” in the function

setting column.

• Connect the unit to an ordinary TV. Set the “TV DISPLAY” to “4:3/PS” or “4:3/LB” in the function

setting column.

Preparation Before Operation

CONNECTIONS

Before preparing this unit for operation, make sure all equipments are turned off.

The unit has several types of output modes like A/V output, S-VIDEO output, digital signal output

(COAXIAL). You may select as needed.

CONNECTED TO A TV

Be sure your TV is on the Video Input

channel before you press Setup to select

your settings.

You will see the Setup menu on your TV

screen.

APEX DIGITAL

AD-703

Preparation Before Operation

CONNECTED TO AN ORDINARY AMPLIFIER

• This connection is for Analog Audio only.

CONNECTED TO A RECEIVER WITH DOLBY DIGITAL/DTS DECODER

CONNECT TO A RECEIVER WITH 5.1 CHANNEL SURROUND SOUND

14 APEX DIGITAL AD-703

Preparation Before Operation

CONNECT TO A RECEIVER WITH 5.1 CHANNEL SURROUND SOUND

NOTICE

• When enjoying karaoke, connect fixed Audio out to L/R jack of 5.1 channel AMP.

• Do not insert the power cord to outlet or switch POWER button before finishing connections.

1. Some discs with Dolby or MPEG AUDIO recorded 5.1

channel track. When connecting a receiver with 5.1

channel input terminal and 5.1 speaker, you can enjoy

more realized sound effects at home.

“5 channel” means 2 front speakers (L/R), 2 rear

speakers (L/R) and a center speaker. 0.1 means bass

speaker output. Even if there are no 5.1 speakers, the

unit will output signals to each speaker.

Note:

• A DVD disc with MPEG AUDIO format recorded 7.1 channel

soundtrack, the output signal will be incorporated to 5.1 channel.

• When uing 5.1 Channel Audio Output, set the SPDIF Output to

SPDIF/RAW.

2. SPEAKER SETUP

To obtain perfect surround sound, the following is

recommended:

a) Use high quality speakers.

b) Use rear and center speakers to match with front

speakers (in size and performance).

c) Same distance between all speakers, between

two front speakers and the listening location.

d) If possible, set the bass speakers between two

front speakers (L/R).

Note: Distance between center speakers and listening location,

and distance between rear speakers and listening location

should shorter than the distance between front speakers and

listening location.

APEX DIGITAL

AD-703

Preparation Before Operation

16 APEX DIGITAL AD-703

What is MP3 and VCD?

WHAT IS MP3?

MP3 is a compression form (like zip). The name MP3 stand for Mpeg1 Audio layer 3 and its

compression algorithm is based on a complicated psycho-acoustic model. This model is based on the

fact that the human ear can not hear all the audio frequencies. The human hearing range is between

20Hz to 20khz and it is most sensitive between 2 to 4 kHz. As a result the MP3 compression form is

destructive, that means the compression algorithm causes the file to lose some information so that it

can not be restored to its original content.

When compressing an audio file (encoding) using the MP3 algorithm you can set the desired

encoding level and have any compression level you want. The larger the compressed file the better

the audio quality of the result. The majority of the files available on the internet are encoded in 128

kbits stereo 44kHz which results in a high quality file that is 12 times smaller than the original! This,

of course, has many interesting consequences.

WHAT IS VCD?

Size and shape of any regular music CD with the same digital audio, plus good video capability. It is

a new video format that offers exceptional high-end digital picture quality and smoothness, over an

hour of playing time, full CD-quality, stereo sound, and more. Using MPEG (Motion Picture Expert

Group) compression (1:30), VCD’s offer picture quality that is far superior to the Quicktime movies you

see on standard VHS tape.

DTS and DTS Digital Out are trademarks of Digital

Theater System, Inc.

Manufactured under license from Dolby Digital

Laboratories. Dolby and the Double-D symbol are

trademarks of Dolby Laboratories. Confidential

unpublished works. 1992-1997 Dolby Laboratories,

This product incorporates copyright protection

technology that is protected by method claims of

certain U.S. patents and other intellectual property

rights owned by Macrovision Corporation and other

rights owners. Use of this copyright protection

technology must be authorized by Macrovision

Corporation, and is intended for home and other

limited viewing uses only unless otherwise

authorized by Macrovision Corporation. Reverse

engineering or disassembly is prohibited.

It is forbidden by law to copy, broadcast, show,

broadcast on cable, play in public, and rent

copyrighted material without permission.

DVD video discs are copy protected, and any

recordings made from these discs will be distorted.

APEX DIGITAL

AD-703

Continued

Basic Operations

TV/AUDIO SELECTION

Press POWER on the TV and audio system.

1. Press “TV/VIDEO” on the TV, select VIDEO mode (TV).

• Select S-VIDEO mode to connect to S-VIDEO (if available).

2. Select the correct audio input on the receiver.

• Each receiver is different from another, please refer to the manual of the receiver.

(e.g., connect the audio output of the DVD to audio input of the receiver.)

Note: This step can be cancelled if you do not connect it to the receiver.

1. Press the POWER button to turn on the unit.

2. Press to open the disc tray and load a disc with the label side up.

3. Press again to close the disc tray. The unit begins to read the disc.

4. Press to play the disc.

After step 4 is finished:

• PLAY DVD

The TV Screen shows DVD menu and title menu.

• PLAY SUPER-VCD, VCD 2.0

The TV Screen shows the menu, the unit enters PBC status.

• PLAY CD, VCD 1.1

Press , the unit plays the disc according to the track numbers.

5. Press to stop playback.

• You have to push this button twice to stop the playback properly.

6. Remove the disc and power off the unit.

DOLBY

D I G I

T A L

TV/VIDEO

DVD/LD

PLAY DISCS

1. If the system of the TV is PAL:

Press SYSTEM and select PAL.

18 APEX DIGITAL AD-703

Basic Operations

SYSTEM SETTING

According to the system of the TV to be connected, set the system of the unit to make it match the TV.

PAUSE

Press STEP.

• When playing pictures:

If the pictures of DVD and VCD are played, press STEP to make playback pause. The

unit enters step play status. Press STEP again, the unit plays a frame forward.

• When playing music CD:

Press STEP to make playback pause.

Press STEP again to resume playback.

The screen shows:

PAL

2. If the system of the TV is NTSC:

Press SYSTEM and select NTSC.

The screen shows:

NTSC

3. If the system of the TV is multi-

system:

Press SYSTEM and select AUTO.

The screen shows:

AUTO

Note: SYSTEM button works only with DVD,

SUPER-VCD and VCD discs.

OSD When the unit is operated, the TV screen shows the operation functions and information

about the disc.

Press OSD to select. OSD OFF

VOLUME CONTROL

Press VOLUME on the TV or amplifier to adjust the volume or press VOLUME on the

remote control.

1. Press + to raise the volume.

2. Press - to lower the volume.

Note: Volume control will not be available on Digital Audio output (SPDIF/RAW or SPDIF/PCM).

SYSTEM SYSTEM

SYSTEM

OSD

STEP

VOLUME

+ -

PBC PLAY (PBC - PLAY BACK CONTROL)

When playing a SUPER-VCD, VCD 2.0, you can enjoy the basic interactive function.

Example: VCD 2.0

1. Press , the screen shows the home menu.

2. Press number buttons to select.

Example: select home menu 1.

3. The screen shows the sub-menu after the unit enters home menu 1.

4. Press or to see the previous or next page.

5. Press number buttons to select sub-menus.

Example: Press number button 5, the unit plays track.

6. Press RETURN to return to the sub-menu, press it again to return to the home menu.

12. ................

13. ................

14. ................

15. ................

16. ................

APEX DIGITAL

AD-703

Basic Operations

ROOT MENU 1. ................

2. ................

3. ................

4. ................

5. ................

11. ...............

ROOT MENU 12. ................

13. ................

14. ................

15. ................

16. ................

ROOT MENU

+10 3

TITLE

SELECT 01

1. .................

2. .................

3. .................

1. .................

2. .................

3. .................

4. .................

5. .................

1. .................

2. .................

3. .................

4. .................

5. .................

DVD MENU PLAY

Some DVDs have title menus and chapter menus.

Press , the screen shows the menu.

Press or to see the next page, select with number buttons

and direction buttons.

1. Press to enter the next menu.

2. Press number buttons to select directly.

Example: select track 13.

You can also do as follows:

1. Press to select track 13.

Press TITLE once to return to the title menu;

press it again to return to the current playback.

Press MENU once to return to the root menu;

press it again to return to the current playback.

20 APEX DIGITAL AD-703

Basic Operations

SELECT WITH NUMBER BUTTONS

Load a disc. Press number buttons to select tracks after the unit finishes reading the disc.

1. If the track number is less than 10, just push buttons 1-10.

Example: push 8 to select track 8.

2. If the track number is over 10, press +10 once

and a button among 1-10.

Example: if you select track 12, press +10 once and button 2.

SELECT DISC

1. Press 1, the unit selects disc 1 to play.

2. Press 2, the unit selects disc 2 to play.

3. Press 3, the unit selects disc 3 to play.

4. Press DISC SKIP, the unit selects next disc to play.

Press the button again, the unit selects the discs circularly.

EXCHANGE DISCS

1. Press EXCHANGE to open the disc tray

2. Unload the disc and load another one.

3. Press EXCHANGE again to close the disc tray.

TRACK08 00:21

+10 2

The screen shows:

TRACK12 00:00

The screen shows:

1DISC 1

The screen shows:

2DISC 2

The screen shows:

3DISC 3

The screen shows:

DISC SKIP DISC SKIP

The screen shows:

EXCHANGE

APEX DIGITAL

AD-703

Play Discs in Various Ways

AUDIO MODE

You may select a needed language from a multi-language DVD and SUPER-VCD.

You may select the right channel, left channel, or stereo from a multi-channel CD or VCD.

WHEN PLAYING DVD

Press , the screen shows orderly:

Different discs differ in languages.

1 AUDIO 1/4: MPEG 2CH ENGLISH

2 AUDIO 2/4: MPEG 2CH SPANISH

3 AUDIO 3/4: MPEG 2CH FRENCH

4 AUDIO 4/4: MPEG 2CH CHINESE

AUDIO 1/4: AC-3 2CH ENGLISH

The screen shows:

AUDIO 2/2: AC-3 2CH SPANISH

MUTE

MUTE OFF

WHEN PLAYING VCD OR CD

Press AUDIO MODE, the screen shows orderly:

MUTE When playing a disc, this function can remove the sound.

1. REMOVE SOUND

Press MUTE, the screen shows “MUTE”.

2. RESUME SOUND

Press MUTE again, the screen shows “MUTE OFF”.

MONO L

STEREO

MONO R

AUDIO MODE

NOTICE

• Different discs differ in language.

• As to a two-language function VCD, you may push AUDIO MODE to select a needed language.

• AUDIO MODE works when playing a SUPER-VCD, you may select mono channel (left or right) or stereo.

You may select one mode.

AUDIO MODE

MUTE

LANGUAGE

22 APEX DIGITAL AD-703

Continued

Play Discs in Various Ways

FAST PLAY

When playing a disc, you may play it forward fast or reverse it fast to find what you need.

SLOW PLAY

Enjoy slow motions by the following steps.

WHEN PLAYING DVD

1. Press to play slowly.