Arista Networks C130 802.11a/b/g/n/ac AP User Manual
Mojo Networks, Inc. 802.11a/b/g/n/ac AP Users Manual
Contents
Users Manual
C-130 Mojo Access Point Quick Start Guide Package Contents The C-130 package must contain the following components. C-130 15/16” (24mm) Mounting Bracket Mounting the C-130 1. Afix bracket to T - Grid. 3. Place the first mounting post on the rear-side of the device on to the lower notch of the bracket. 2. Rotate bracket to snap on to T- Grid. 4. Rotate the device such that the center mounting post fits in to the center notch on the bracket. 5. Ensure that all the mounting posts on the rear-side of the device are snapped in to the respective notches on the bracket. Getting the C-130 Online Step 1: Power Up the Device Plug one end of an Ethernet cable into the PoE+ (802.3at) switch or injector and the other end into the Ethernet/PoE+ port on the C-130. Ensure the PoE+ source you are using is turned ON. Note: You can also use regular PoE (802.3af). However it will disable some features. To know more refer to C-130 Installation Guide. OR As an alternative to PoE+, you can insert a compatible power adaptor plug into an AC power outlet and the other end into the power input port on the C-130. Warning: If you are not using PoE+, ensure that you use only an AC power adaptor supported by the C-130 access point (AP). Step 2: Connect the Device to the Network If you are using a PoE+ injector, make sure the data connection is plugged into a suitable switch port with proper network connectivity. Step 3: Check the LED Status After the device is powered ON and connected to the network, a few minutes will pass until the Power/Ethernet (small globe) turns solid GREEN. This indicates the AP is online and operational. Troubleshooting After the C-130 is connected to the network and powered ON, if the LED for Power/Ethernet is not Solid Green, the AP has encountered a problem or is in the upgrade process. The following guidelines may help you to quickly diagnose and fix the problem. LED Status Power/ Ethernet Wi-Fi 2.4GHz What does it mean? Wi-Fi 5GHz Solid Orange Any Any The AP does not have an active Ethernet link1 Fast Blink Green Any Any The AP did not receive a valid IP address via DHCP2 Slow Blink Green Any Any The AP is unable to connect to the Mojo Cloud Services or Mojo Server3 Slow Blink Orange Any Any The AP is being upgraded Note: If Power/Ethernet LED is Yellow, the device is plugged into a non-Gigabit Ethernet switch port. Using an 802.11 ac Access Point on a 100Mb or 10Mb Ethernet connection can cause performance issues in the WLAN. Use Gigabit Ethernet uplinks when possible. 1. Check whether the Ethernet cable is plugged into the correct port (PoE+) on the C-130 and the other end of the cable is plugged into an Ethernet jack or port on a switch that is turned ON. 2. If the C-130 did not receive a valid IP address from the DHCP server, check wether the DHCP server is ON and available on the VLAN/subnet to which the AP is connected. If the AP still fails to get a valid IP address, reboot the device once to see if the problem get resolved. 3. If you are using Mojo Cloud Services, then open the TCP port 443 (SSL). If you have an on-premises installation, then open the ports UDP 3851 and port 80. If you are using a Proxy, Web Accelerator or URL Content Filter in between the AP and the Internet, ensure the settings allow communication between the AP and Mojo Cloud Services. If your configuration requires you to specify an exact IP address or IP range for Mojo Cloud Services, please contact Technical Support. If you are still unable to resolve the problem, contact the local Mojo Networks Sales Engineer or 24/7 Mojo Networks Technical Support. Tel: +1 (650) 641 0027 Email: support@mojonetworks.com Mojo Networks, Inc. 339 N. Bernardo Avenue #200, Mountain View, CA 94043 T +1.877.424.7844 T 650.961.1111 F 650.961.1169 www.mojonetworks.com info@mojonetworks.com © 2016 Mojo Networks, Inc. All rights reserved. Mojo Networks and the Mojo Networks logo are trademarks, and Mojo is a registered trademark of Mojo Networks, Inc. All other trademarks mentioned herein are properties of their respective owners. Specifications are subject to change without notice.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Create Date : 2016:06:16 18:18:55+05:30 Creator : Adobe InDesign CC 2015 (Macintosh) Modify Date : 2016:07:19 01:26:35+08:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.6-c015 84.158975, 2016/02/13-02:40:29 Metadata Date : 2016:07:19 01:26:35+08:00 Creator Tool : Adobe InDesign CC 2015 (Macintosh) Instance ID : uuid:e7f0dd40-bd7e-4ebe-bbf8-e4a6ef6b97a7 Original Document ID : xmp.did:7A30FF0DAD6EE211817E93E08AE83754 Document ID : xmp.id:089b1117-fb17-403f-a9c4-fc9bf09b8a7b Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:099ea3ff-aadb-4f42-8651-9a1dd8045a2e Derived From Document ID : xmp.did:27AA1FE01DCAE311B13C9875ED59DC9B Derived From Original Document ID: xmp.did:7A30FF0DAD6EE211817E93E08AE83754 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2015 (Macintosh) History Changed : / History When : 2016:06:16 18:18:55+05:30 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 4EXIF Metadata provided by EXIF.tools