Arts Digital Technology CE7000BT Handheld Bluetooth Speaker with Speakerphone User Manual
Arts Digital Technology (HK) Limited Handheld Bluetooth Speaker with Speakerphone
Contents
- 1. User Manual-1
- 2. User Manual-2
User Manual-1
INSTRUCTION MANUAL
CE7000-BT
Handheld Bluetooth Speaker
With Speakphone
Thank you for purchasing this Handheld Bluetooth Speaker With Speakphone. Please read this
instruction manual carefully before using this product to ensure proper use. Keep this manual in a
safe place for future reference.
1
WHAT’S IN THE BOX
Contents
1. CE7000-BT Handheld
Bluetooth Speaker
2. AC-DC Power Adaptor
3. Instruction Manual
4. Warranty Card
If you are missing any parts above, please contact ADT Digital LLC.
Tel: 561 922 6886
Fax: 561 922 6159
2
Cet appareil numérique de la classe B est
FCC ID : OWT-CE7000BT
IC : 10607A-CE7000BT
The CAUTION marking is located on the
bottom / rear panel.
conforme à la norme NMB-003 du Canada.
WARNINGS
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation of
the device.
Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for
the transmitter
by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its
gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more
than that necessary for successful communication.
3
NOTE: This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as
set out in the radio interference regulations of Industry Canada.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils
numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par Industrie Canada.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television (which can be determined by turning the equipment off),
the user is encouraged to try to correct the interference by one or more of the following measures:
FCC AND CANADIAN ICES
Read Instructions –All the safety and operating instructions should be read before the product
is operated.
Retain Instructions – The safety and operating instructions should be retained for future
reference.
Heed Warnings - All warnings on the product and in the operating instruction should be
adhered to.
Follow Instructions – All operating and use instructions should be followed.
Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a dry cloth only for cleaning the exterior only. Do NOT attempt to clean
the inside.
Attachments – Do not use attachments not recommended by the product manufacturer as they
may cause hazards.
Water and Moisture – Do not use this product near water – for example, near a bath tub, wash
bowl, kitchen sink, or laundry tub; in a wet basement, or near a swimming pool, and the like.
Accessories – Do not place this product on an unstable cart, stand tripod, bracket, or table.
The product may fall, causing serious injury to a child or adult, and serious damage to the
product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer,
or sold with the product. Any mounting of the product should follow the manufacturer’s
instructions, and should use a mounting accessory recommended by the manufacturer.
Ven
1.
2.
3.
4.
5.
6.
7.
8.
10.
9.
tilation – Slots and openings in the cabinet are provided for ventilation and to ensure
reliable operation of the product and to protect it from overheating, and these openings must not
be blocked or covered. The openings should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not be placed in a built-in installation
such as a bookcase or rack unless proper ventilation is provided.
A product and cart combination should be moved with care. Quick stops, excessive
force, and uneven surfaces may cause the appliance and cart combination to overturn.
4
Power Sources – This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For products intended to operate from
battery power, or other sources, refer to the operating instruction.
Grounding or Polarization – This product may be equipped with a polarized alternating current
line plug (a plug having one blade wider than the other). This plug will fit into the power outlet
only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarized plug.
Power-Cord Protection – Power supply cords should be routed so that they are not likely to be
walked on or pinched by items placed upon or against them, paying particular attention to cords
at plugs, convenience receptacles, and the point where they exit from the product.
Lightning – For added protection for this product during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the product due to lightning and
power-line surges.
Overloading – Do not overload wall outlets, extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
Object and Liquid Entry
11.
12.
13.
14.
15.
16. – Never push objects of any kind into this product through openings
as they may touch dangerous voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
Serving – Do not attempt to service this product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
17.
Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a) When the power-supply cord or plug is damaged,
b) Liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions. Adjust
only those controls that are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will of then require extensive
work by a qualified technician to restore the product to its normal operation.
e) If the product has been dropped or damaged in anyway, and
f) When the product exhibits a distinct change in performance – this indicates a need for
service.
18.
Replacement Parts – When replacement parts are required, be sure the service technician has
used replacement parts specified by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Safety Check – Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper operating
condition.
19.
20.
5
Heat21.
22.
23.
24.
25.
– The product should be situated away from heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that produce heat.
Unplug this apparatus during lighting storms or when unused for long periods of time.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or metal capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the appliance.
Ensure children and babies do not play with plastic bags or any packaging materials.
•
•
•
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
The apparatus shall notbe exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on apparatus.
Mains plug /Power adaptor is used as disconnect device and it should remain readily operable
during intended use. In order to disconnect the apparatus from the mains completely, the main
plug/power adaptor should be disconnected from the mains socket outlet completely.
WARNINGS
6
1. STATUS indicator
2. PAIR/ ANSWER / END button
PLAY/ PAUSE button
3. VOLUME -button
4. Speaker (L ch.)
5. POWER STANDBY / REJECT CALL button
6. VOLUME +button
7. Speaker (R ch)
8. AUX IN jack
9. POWER ON/OFF switch
10.Battery compartment
11.DC IN jack
1
8
10
9
6
7
11
2
3
4
5
FRONT SIDE
REAR SIDE
CONTROL LOCATION
7
MAKING THE CONNECTIONS
1. Remove the battery compartment cove r.
2. Install 4 “AA” size (UM-3) batteries (not included) in the battery compartment
following the polarity markings shown on it.
3. Replace the battery compartment cover.
Battery Precautions (Use
Battery Installation
AA Size UM-3 (LR6) x 4 pieces)
The precautions below should be followed when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in
the battery compartment. Reversed batteries may cause damage to the device.
3. Do not mix different type of batteries together (e.g. Alkaline and Carbon Zinc) or
old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to
prevent damage or injury from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged, they can overheat
and rupture
(Follow battery manufacturer’s directions).
6. Rechargeable batteries are to be removed from the product before being charged.
7. Rechargeable batteries are only to be charged under adult supervision.
8. Exhausted batteries are to be removed from the product.
9. The supply terminals are not to be short-circuited.
10.Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
Connecting to AC-DC Power Adaptor
Before using your Bluetooth speaker, you should connect it to AC (mains) power.
1. Firmly and securely insert the DC plug of the adaptor to the DC jack at the back
of the unit.
2. Plug the adaptor into the AC outlet.
8
MAKING THE CONNECTIONS
OPERATION
When the unit is not operated by the AC power or unused for long period of time,
please remove the power adaptor from the wall outlet and unplug from the unit.
1. After connecting the AC power, turn ON the POWER switch on the rear of the
unit, the STATUS indicator will light up in RED to indicate that the unit is in
standby mode.
POWERING ON/OFF THE UNIT
2. Press the “ ” button once to turn on the unit.
3. After using the unit, press and hold the “ ” button for 2 seconds to switch the
unit to standby mode, or turn OFF the POWER switch. The STATUS indicator
will light off.
1. After powering on your unit, you can start pairing process to connect to your
Bluetooth device.
PAIRING YOUR BLUETOOTH DEVICE
About pairing
Pairing is the term used when two Bluetooth devices are connected wirelessly for the
first time. This allows the devices to see each other and sets up a one to one
communication channel between both devices.
Pairing with a Bluetooth device
2. If it is the first time setup after purchasing, the STATUS indicator will flash RED
and BLUE alternatively to ask for pairing, BLUE/RED flashing indicates pairing
attempt is in process.
3. Turn on Bluetooth functionality on your device and make it discoverable (see
your device’s instructions to add or setup a Bluetooth device).
4. Select CE7000-BT on you Bluetooth device to make the pairing when it is
found. If you device asks for a passkey, enter “0000” on the keyboard of your
device. If no device is paired in 3 minutes, the unit will power off (switch to
standby mode). If this occurs, retry step 1 - 4.
5. Once paired with a device, a blue light on the STATUS indicator will glow
steadily and two beep sounds confirms that pairing is completed. On some
devices, you must then select “use as a stereo audio device” or similar on the
device’s Bluetooth manual. Once paired, your device should connect to the
CE7000-BT whenever within the Bluetooth range (10 metres).
9
OPERATION
To connect previously paired Bluetooth device
1. Your Bluetooth speaker can store one previously paired device for quick
pairing during power on.
2. To connect a previously paired device after power on, if the previously paired
device is found with the range, the unit will pair the device automatically and
the STATUS indicator will turn to BLUE steadily. Two beeps will confirm the
pairing is completed.
To connect a new Bluetooth device
1.
2. During this period, you can pair a new Bluetooth device. Please follow step 3 to
5 in “To begin pairing with a Bluetooth device” section to complete the
pairing of a new Bluetooth device.
3. You can also start the pairing process manually by pressing and holding the
PAIR button on the unit until STATUS indicator would flash in RED and BLUE
alternatively again to indicate pairing attempt is in process.
NOTE:
•Due to different operating system of Bluetooth devices, the time taken by pairing
process might be different. If the pairing cannot be successful in the first time,
please try to restart the pairing process by pressing and holding the PAIR button
again until the indicator light flashes red and blue alternatively.
•The pairing time might be longer for the first time pairing or pairing a new
Bluetooth device.
•Make sure you have the latest firmware for your Bluetooth mobile devices.
•Make sure your device is working properly. Check your device’s manual for details
on Bluetooth pairing and linking.
1. Follow the “PAIRING YOUR BLUETOOTH DEVICE” section to connect your
Bluetooth device.
PLAYING MUSIC VIA BLUETOOTH
To listen to music streamed wirelessly from your paired Bluetooth device.
2. Start the audio playback and adjust the volume output on your Bluetooth
device.
3. Press and release the PAIR button to pause the audio playback from your
Bluetooth device and press and release this button for resume the playback.
You may also pause and resume the playback on your Bluetooth device.
NOTE: It is not recommended to pause the audio playback by pressing and
releasing the PAIR button on the unit and then resuming the playback on your
Bluetooth device as it may have abnormal response for some Bluetooth
devices.
4. Use the Volume +/- buttons on the unit to adjust volume.
5. When done listening, press and hold the “ ” button for 2 seconds to turn the
unit off (switch to standby mode).
If no previously paired device is found with the Bluetooth range (10 metres)
after power on, the STATUS indicator would continue to flash in BLUE and
RED for 3 minutes before switching to standby mode.
10
OPERATION
USING THE SPEAKERPHONE
To use your Bluetooth speaker as a speakerphone for receiving a phone call from a
Bluetooth enabled phone.
1. Follow the “PAIRING YOUR BLUETOOTH DEVICE” section to set up the
Bluetooth connection.
2. When a call is received during music is playing, music will be muted to hear the
ringtone. STATUS indicator will flash in RED color to indicating the incoming
call. Press the “ANSWER” button to answer the call, or press the “ ” button to
ignore the call.
NOTE: The voice from the unit will be in “MONO” mode when the Speaker
phone is being used and only the right hand side speaker will sound.
3. Use the Volume+/- buttons to adjust the desired volume level.
4. When the call is completed, press the “END” button to end the call and resume
previous function or music playback.
NOTE:
The position of the built-in microphone of the unit is on the central of the front side.
You are recommended to face the front side of the unit and at a short distance in order
to have good voice quality and clarity.
USING THE AUX IN JACK
1. Plug one end of the AUX IN cable (not included) into the headphone jack (or
audio out) of your audio device and the other end into the AUX IN jack of the
unit.
2. Press and hold the “ ” button for 2 seconds to turn on the unit (release when
blue light appears).
3. Use your audio device to control music playback and volume through the unit.
4. Use the Volume+/- buttons to adjust the desired volume level.
5. When done listening, press and hold the “ ” button for 2 seconds to turn
the unit off (switch to standby mode) and unplug the AUX IN cable from the unit.
Remember to turn off your audio device too.
11
OPERATION
CARE AND MAINTENANCE
NOTE:
•Play/Pause control only works in Bluetooth mode. It does not control the
plugged-in device.
•When you plug in the AUX IN cable during Bluetooth playback, the Bluetooth
playback will be interrupted and switched to the AUX mode. After unplugging the
AUX IN cable from the unit, the music may be or may not be resumed depending
on different Bluetooth devices. If the music has been pause on you device, please
restart / resume playback on your device manually. Alternatively you can restart
Bluetooth playback following the “playing music via Bluetooth” section.
•Only using AUX IN cable with standard 3.5mm stereo plug ( do not use any cable
with “mono” plug).
PLACING THE UNIT
Place the unit on a level surface away from sources of direct sunlight or excessive
heat. Protect your furniture when placing your unit on a natural wood and lacquered
finish. A cloth or other protective material should be placed between it and the
furniture.
CLEANING THE UNIT
Do not clean your unit by water directly.
Clean your unit with a soft cloth moistened only with mild soap and water. Stronger
cleaning agents, such as Benzene, thinner or similar materials can damage the
surface of the unit.
12
TROUBLE SHOOTING
PROBLEM
If you have followed the instructions and are having difficulty operating the unit, locate
the PROBLEM in the left column below. Check the corresponding POSSIBLE CAUSE
column to locate and remedy the problem.
POSSIBLE CAUSE SOLUTION
No sound when
playing audio via
Bluetooth
Your Bluetooth device has
not been paired properly.
Pairing your Bluetooth device
according to the “PAIRING
YOUR BLUETOOTH DEVICE”
section.
The volume control of your
Bluetooth device is set too
low.
Increase the volume of your
Bluetooth device.
The volume control of the
Bluetooth speaker is set too
low.
Increase the volume of the
Bluetooth speaker by pressing
the Volume “+” button.
No sound when
playing audio via
AUX IN
Audio cable has not been
connected properly.
Check the connection of audio
cable at the Bluetooth speaker
and the audio device.
Audio cable has breakage. Use another audio cable for
connection.
The volume control of you
Bluetooth device is set too
low.
Increase the volume of you
Bluetooth device.
The volume control of you
Bluetooth speaker is set too
low.
Increase the volume of the
Bluetooth speaker by pressing
the Volume “+” button.
Sound comes
from only one
speaker when
playing audio via
AUX IN
Mono audio cable is used. Make sure the audio cable is a
stereo type.
The audio cable was
damaged.
Replace the audio cable of
stereo type
The person whom
you call via
speakerphone
cannot hear your
voice clearly.
You are not facing to the
front side of the Bluetooth
speaker.
Face to the front side of the
Bluetooth speaker.
You are too far from the
Bluetooth speaker.
Close to the front side of the
Bluetooth speaker.
13
SPECIFICATION
Power Supply
AC-DC Power Adaptor
DC Input
Input: 100 – 240VAC, 50/60Hz
Output: 5VDC, 1A
4 x “AA” size (UM-3/LR6) Battery (Not included)
Bluetooth Protocol Support A2DP / HFP
Audio Power Output 2 x 2W (rms)
Dimensions 7.52” (W) x 6.69” (H) x 6.50” (D)
191mm (W) x 170mm (H) x 165mm (D)
Weight 1.01 lb
0.46 kg
Specifications are typical, individual units might vary. They are subject to continuous
improvement without notice and without incurring any obligation.