Audiovox aar Systems D189070 Rear Seat Entertainment System - BCU User Manual Bentley RSE Control Unit Installation Guide

Download:
Mirror Download [FCC.gov]
Document ID	2247473
Application ID	nsTXKtZoCPM52a5wXfmSrA==
Document Description	Installation Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	45.57kB (569634 bits)
Date Submitted	2014-04-22 00:00:00
Date Available	2014-04-22 00:00:00
Creation Date	2014-01-28 14:14:19
Producing Software	Microsoft® Word 2010
Document Lastmod	2014-01-28 14:14:19
Document Title	Bentley RSE Control Unit Installation Guide
Document Creator	Microsoft® Word 2010
Document Author:	Heath, James (Bentley)

Bentley RSE Control Unit
Installation Guide
Installation for J829 (aftersales reference)

Control unit 2 for information electronics
(J829) - To remove and fit
General Information
The Control unit 2 for information
electronics -J829- -arrowed- is located
inside the glove box on the outboard
side.
Note
Image shows a right hand drive
vehicle. Left hand drive vehicle is a
mirror image.
Replacement control units require
additional programming via the Vehicle
tester. Refer to Installation
instructions.
Special tools and workshop equipment
required

Removal tool -WT 10221-

Vehicle tester
Torque tightening values
Unless otherwise shown, standard
torque values apply.
→ Rep.-Gr.00
Removal
The following procedure is based on a
right hand drive vehicle. The
procedure is the same for both left
hand and right hand drive.
–
Switch off the ignition.
Insert the removal tools -WT
–
10221- into the slots in the control
unit until they locate.
Note
Ensure that both tools click into
position before attempting to remove
the control unit.
Push and hold the tools outwards
in the direction of the -arrows- to
–
release the retaining clips, then pull
rearwards evenly to slide out the
control unit.
Press the retaining clips -arrowed–
inwards on both sides to release
the removal tools -1-.
Disconnect the harness connectors
–
-1- and remove the control unit -2from the vehicle.
Installation
Installation is the reverse of removal
procedure, noting the following.
Ensure all electrical connectors are
–
connected correctly prior to
installation.
After installation ensure the
catches secure the control unit on
both sides. This can be confirmed
–
by an audible click being heard and
then attempting to withdraw the
control unit without using the
removal tools.
A new control unit will require
coding. Connect the Vehicle tester
to the vehicle and run Software
Version Management (SVM). Refer
–
to "Diagnostic system - Guided
functions/Component
replacement".
→ Rep.-Gr.97
CAUTION: FCC REGULATORY
REQUIREMENTS
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
1-
This device may not cause
harmful interference, and
This device must accept any
2-
interference received, including
interference that may cause
undesired operation.
Any change or modification to the
product not expressly approved by the
manufacturer could void the user's
authority to operate the device.
FCC RF Radiation Exposure
Statement:
This equipment contains a radio
transmitter. It is designed and
manufactured not to exceed the
emission limits for exposure to radio
frequency energy set by the Federal
Communication Commission (FCC) of
the US Government in accordance
with part 2.1091 of the FCC Rules for
an uncontrolled environment.
The equipment is installed to ensure a
minimum 20 cm distance between the
two antennas and, with a minimum
safe operating distance of 20 cm
between the respective antennas and
the car occupants
CAUTION: IC REGULATORY
REQUIREMENTS
This device complies with Industry
Canada licence-exempt RSS
standard(s). Operation is subject to the
following two conditions:
1-
This device may not cause
interference.
This device must accept any
interference, including
2 - interference that may cause
undesired operation of the
device.
Any change or modification to the
product not expressly approved by the
manufacturer could void the user's
authority to operate the device.
IC RF Radiation Exposure Statement:
This equipment contains a radio
transmitter. It is designed and
manufactured not to exceed the
emission limits for exposure to radio
frequency energy as stated within the
Industry Canada RSS standard(s).
This radio transmitter (IC: 11196AD189070) has been approved by
Industry Canada to operate with the
antenna types listed below with the
maximum permissible gain and
required antenna impedance for each
antenna type indicated. Antenna types
not included in this list, having a gain
greater than the maximum gain
indicated for that type, are strictly
prohibited for use with this device.
Antenna Models:
For GSM / UMTS: Smarteq Antenna
AB; part No: 3W7.035.524.A
For Bluetooth / WLAN: WISI
Automotive GmbH & Co. KG; part:
Wisi AG91 WLAN Bentley
4W0.962.131
The equipment is installed to ensure a
minimum 20 cm distance between the
two antennas and, with a minimum
safe operating distance of 20 cm
between the respective antennas and
the car occupants.
ATTENTION: IC EXIGENCES
RÉGLEMENTAIRES
Cet appareil est conforme avec
Industrie Canada RSS exemptes de
licence standard (s). Son
fonctionnement est soumis aux deux
conditions suivantes:
12-
Ce dispositif ne peut causer des
interférences.
Ce dispositif ne peut causer des
interférences.
Tout changement ou modification au
produit non expressément approuvés
par le fabricant peuvent annuler le
droit de l'utilisateur à utiliser l'appareil.
IC Rayonnement RF de Déclaration
d'exposition:
Cet appareil contient un émetteur
radio. Il est conçu et fabriqué pour ne
pas dépasser les limites d'émission
pour l'exposition à l'énergie de
radiofréquence comme indiqué dans la
norme (s) d'Industrie Canada RSS
Le présent émetteur radio (IC:
11196A-D189070) a été approuvé par
Industrie Canada pour fonctionner
avec les types d'antenne énumérés cidessous et ayant un gain admissible
maximal et l'impédance requise pour
chaque type d'antenne. Les types
d'antenne non inclus dans cette liste,
ou dont le gain est supérieur au gain
maximal indiqué, sont strictement
interdits pour l'exploitation de
l'émetteur.
Modèles d'antenne:
Pour GSM / UMTS: Smarteq Antenna
AB; part No: 3W7.035.524.A
Pour Bluetooth / WLAN: WISI
Automotive GmbH & Co. KG; part:
Wisi AG91 WLAN Bentley
4W0.962.131
L'équipement est installé pour assurer
une distance minimale de 20 cm entre
les deux antennes et, avec une
distance de fonctionnement minimale
de sécurité de 20 cm entre les
antennes respectives et les occupants
de la voiture.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 8
Language                        : en-GB
Tagged PDF                      : Yes
Title                           : Bentley RSE Control Unit Installation Guide
Author                          : Heath, James (Bentley)
Subject                         : Installation for J829 (aftersales reference)
Creator                         : Microsoft® Word 2010
Create Date                     : 2014:01:28 14:14:19+00:00
Modify Date                     : 2014:01:28 14:14:19+00:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools