AzureWave Technologies NM230NF IEEE 802.11 b/g/n Wireless LAN and Bluetooth combo M.2 1216 module User Manual Safety and regulatory guide

AzureWave Technologies, Inc. IEEE 802.11 b/g/n Wireless LAN and Bluetooth combo M.2 1216 module Safety and regulatory guide

Contents

User manual statement

Safety and regulatory guide
Important health information and safety precautions
When using this product, the safety precautions below must be taken to avoid possible legal liabilities and damages.
Retain and follow all product safety and operating instructions. Observe all warnings in the operating instructions on the
product.
To reduce the risk of bodily injury, electric shock, fire, and damage to the equipment, observe the following precautions.
Electrical safety
This product is intended for use when supplied with power from the AA batteries. Other usage may be dangerous and
will invalidate any approval given to this product.
Safety precautions for AA batteries
Handle battery packs carefully
This product contains a AA batteries. There is a risk of fire and burns if the battery pack is handled improperly.
WARNING: To reduce risk of fire or burns, do not disassemble, crush, puncture, short external
contacts or circuits, expose to temperature above 60° C (140° F), or dispose of in fire or water.
Recycle or dispose of used batteries according to the local regulations or reference guide supplied
with your product.
Take extra precautions
Avoid dropping the device. If the device is dropped, especially on a hard surface, and the user suspects damage,
take it to a service centre for inspection.
If the battery leaks:
Do not allow the leaking fluid to come in contact with skin or clothing. If already in contact, flush the affected area
immediately with clean water and seek medical advice.
Do not allow the leaking fluid to come in contact with eyes. If already in contact, DO NOT rub; rinse with clean water
immediately and seek medical advice.
Take extra precautions to keep a leaking battery away from fire as there is a danger of ignition or explosion.
Safety precautions for direct sunlight
Keep this product away from excessive moisture and extreme temperatures. Do not leave the product inside a vehicle
or in places where the temperature may exceed 60°C (140°F), such as on a car dashboard, window sill, or behind glass
that is exposed to direct sunlight or strong ultraviolet light for extended periods of time. This may damage the product,
overheat the battery, or pose a risk to the vehicle.
Safety precautions for RF exposure
Use only original manufacturer-approved accessories, or accessories that do not contain any metal.
Use of non-original manufacturer-approved accessories may violate your local RF exposure guidelines and should be
avoided.
Electrical safety
Accessories
Use only approved accessories.
Do not connect with incompatible products or accessories.
Faulty and damaged the device
Do not attempt to disassemble this device or its accessory.
Only qualified personnel must service or repair this device or its accessory.
General precautions
Protect your device
Always treat your product with care and keep them in a clean and dust-free place.
Do not expose your product to open flames or lit tobacco products.
Do not drop, throw or try to bend your product.
Do not use harsh chemicals, cleaning solvents, or aerosols to clean the product.
Do not paint your product.
Do not attempt to disassemble your product, only authorised personnel must do so.
Store your product at temperatures between 0°C to 40°C.
Please check local regulations for disposal of electronic products.
Damage requiring service
Unplug the product from the electrical outlet and refer servicing to an authorized service technician or provider under
the following conditions:
The product has been damaged by exposure to liquid, dropped, subject to impact or damaged.
There are noticeable signs of overheating.
The product does not operate normally when you follow the operating instructions.
Avoid hot areas
The product should be placed away from heat sources such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
Avoid using your device after a dramatic change in temperature
When you move your product between environments with very different temperature and/or humidity ranges,
condensation may form on or within the device. To avoid damaging the device, allow sufficient time for the moisture
to evaporate before using the device.
NOTICE: When taking the device from low-temperature conditions into a warmer environment or from
high-temperature conditions into a cooler environment, allow the device to acclimate to room temperature before
turning on power.
Avoid pushing objects into product
Never push objects of any kind into cabinet slots or other openings in the product. Slots and openings are provided
for ventilation. These openings must not be blocked or covered.
Small children
Do not leave your device and its accessories within the reach of small children or allow them to play with it. They
could hurt themselves or others, or could accidentally damage the device. Your device contains small parts with
sharp edges that may cause an injury or which could become detached and create a choking hazard. Consult the
doctor immediately if the accessories or battery are swallowed.
Repetitive motion injuries
To minimize the risk of repetitive strain injuries:
Do not grip the device too tightly
Press the buttons lightly
Regulatory agency identifications
For regulatory identification purposes, your product is assigned a model number of 2PQ6.
To ensure continued reliable and safe operation of your device, use only the accessories listed below with your 2PQ6:
Battery Pack with model number AA batteries
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio or television technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC RF Radiation Exposure Statement:
This equipment has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines rules. This transmitter must not be
co-located or operated in conjunction with any other antenna or transmitter.
[ IC ]
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of
the device.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement."
RF Radiation Exposure Statement:
This equipment has been tested and found to comply with IC radiation exposure limits set forth for an uncontrolled
environment and meets the RSS-102 of the IC radio frequency (RF) Exposure Guidelines rules. This transmitter must
not be co-located or operated in conjunction with any other antenna or transmitter.
éclaration d'exposition aux radiations RF :
Cet équipement a été testé et jugé conforme aux limites IC d'exposition aux radiations définies pour un environnement
non contrôlé et répond aux règles des directives d'exposition aux radiofréquences (RF) CNR-102 IC. Cet émetteur ne
doit pas être placé ou opéré conjointement avec une autre antenne ou un autre émetteur.
Contain IC: 6100A-NM230NF
[CE]
This device complies with the R&TTE Directive (1999/5/EC) issued by the Commission of the European Community.
We declare under our sole responsibility that our product and in combination with our accessories, to which this
declaration relates is in conformity with the appropriate standards EN 300 328, EN 301 489-1 -17, EN62209-2,
EN62479, EN 60950 following the provisions of, radio equipment and telecommunication terminal equipment
directive 1999/ 5 /EC.
[ NCC ]
[警語內容]
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大
功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，
並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍
受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
WEEE notice
Please do not discard your device in a landfill. Electronic devices contain substances that may be
hazardous to the environment if not properly disposed of. For more information about electronic and
electrical waste equipment disposal, recovery, and collection points, please contact your local city center,
household waste disposal service, shop from where you purchased the equipment, or manufacturer of
the equipment.
RoHS compliance
This product is in compliance with Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011,
on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS) and its
amendments.
EXPLANATION OF THE GRAPHIC SYMBOLS
KRYMDA4XXXXX
Designation of the serial number of every device,
applied at the device.
(Number as an example)
“Please note the accompanying
documents“
or “Observe operating instructions”
Krell Precision (Yang Zhou)Co.,Ltd
NO.28 XingYang Road,Development Area,
YangZhou City ,JiangSu Province.
Identification of manufacturer of
medical product including address
Carefully read this operation manual before setup and
commissioning, even if you are already familiar with
Charger scales.
“Electro-medical appliance“
with attachment for type BF
+60°C
Transport and storage temperature limit
indicating the upper and the lower limit
(Transport and storage temperature on
-20°C
(Drawing will be Modify base on ID
Design)
packaging)
EMC GUIDANCE AND MANUFACTURE’S DECLARATION
Guidance and manufacturer’s declaration-electromagnetic emissions
The SCALE 2PQ6 is intended for use in the electromagnetic environment specified below.
The customer or the user of the SCALE 2PQ6 should assure that it is used in such an environment.
Emission test
Compliance
Electromagnetic
environment-guidance
RF emissions
CISPR 11 Group 1
The SCALE 2PQ6 uses RF energy only for
its internal function. Therefore, its RF
emissions are very low and are not likely to
cause any interference in nearby electronic
equipment.
RF emissions
CISPR 11 Class B
The SCALE 2PQ6 is suitable for use in all
establishments, including domestic
establishments and those directly
connected to the public low-voltage power
supply network that supplies buildings used
for domestic purposes.
Harmonic emissions
IEC 61000-3-2
Class A
Voltage fluctuations
/flicker emissions
IEC 61000-3-3
Compliance
Guidance and manufacturer’s declaration-electromagnetic immunity
The SCALE 2PQ6 is intended for use in the electromagnetic environment specified below.
The customer or the user of the SCALE 2PQ6 should assure that it is used in such an environment.
Immunity test
IEC 60601 test level
Compliance
L evel
Electromagnetic
environment-guidance
Electrostatic
discharge(ESD)
± 6 kV contact
± 8 kV air
± 6 kV contact
± 8 kV air
Floors should be wood,
concrete or ceramic tile.
IEC 61000-4-2
If floors are covered with
synthetic material, the
relative humidity should
be at least 30%
Electrical fast
transient/burst
IEC 61000-4-4
± 2kV for power
supply lines +
1kV for
input/output lines
± 2kV for power
supply lines Not
applicable
Mains power quality
should be that of a typical
commercial or hospital
environment.
Surge IEC
61000-4-5
± 1kV line(s) to
line(s) ± 2kV
line(s) to earth
± 1kV differential
mode Not
applicable
Mains power quality
should be that of a typical
commercial or hospital
environment.
Voltage Dips,
short
interruptions
and voltage
variations on
power supply
input lines IEC
61000-4-11
<5% UT(>95%
dip in UT) for 0,5
cycle 40%
UT(60% dip in
UT) for 5 cycles
70% UT(30%
dip in UT) for 25
cycles <5%
UT(>95% dip in
UT) for 5 s
<5% UT(>95%
dip in UT) for 0,5
cycle 40%
UT(60% dip in
UT) for 5 cycles
70% UT(30%
dip in UT) for 25
cycles <5%
UT(>95% dip in
UT) for 5 s
Mains power quality
should be that of a typical
commercial or hospital
environment. If the user
of the SCALE 2PQ6
requires continued
operation during power
mains interruptions, it is
recommended that the
SCALE 2PQ6 be powered
from an uninterruptible
power supply or a battery.
Power
frequency(50/60
Hz) magnetic
field IEC
61000-4-8
3 A/m 3 A/m
The SCALE 2PQ6 power
frequency magnetic
fields should be at levels
characteristic of a typical
location in a typical
commercial or hospital
environment.
NOTE UT is the a.c. mains voltage prior to application of the test level.
Guidance and manufacturer’s declaration-electromagnetic immunity
The SCALE 2PQ6 is intended for use in the electromagnetic environment specified below. The
customer or the user of the SCALE 2PQ6 should assure that is used in such and environment
Immunity test
IEC 60601 test level
Compliance level
Electromagnetic
environment-guidance
Conducted RF
IEC 61000-4-6
Radiated RF
IEC 61000-4-3
3 Vrms
150 KHz to 80 MHz
3 V/m 80MHz to 2,5
GHz
3 Vrms
3 V/m
Portable and mobile RF
communications equipment
should be used no closer to any
part of the SCALE 2PQ6
including
cables, than the recommended
separation distance calculated
from the equation applicable to
the frequency of the transmitter.
Recommended separation
distance:
d = 1,2 √P
d = 1,2 √P 80MHz to 800 MHz
d = 2,3 √P 800MHz to 2,5 GHz
Where P is the maximum output
power rating of the transmitter in
watts (W) according to the
transmitter manufacturer and d is
the recommended separation
distance in metres (m).
Field strengths from fixed RF
transmitters, as determined by an
electromagnetic site surveya,
should be less than the
compliance level in each
frequency rangeb.
Interference may occur in the
vicinity of equipment marked with
the following symbol
:
NOTE1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reflection from structures, objects and people.
a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones
and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be
predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF
transmitters, an electromagnetic site survey should be considered.
b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
Recommended separation distance between portable and mobile RF communications
equipment and the SCALE
The SCALE 2PQ6 is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled.
The customer or the user of the SCALE 2PQ6 can help prevent electromagnetic interference by
maintaining a minimum distance between portable and mobile RF communications equipment
(transmitters) and the SCALE 2PQ6 as recommended below, according to the maximum output power
of the communications equipment.
Rated maximum output
power of transmitter
W
Separation distance according to frequency of transmitter m
150 kHz to 80 MHz
d =1,2
√
P
80 MHz to 800 MHz
d =1,2
√
P
800 MHz to 2,5 GHz
d =2,3
√
P
0,01
0,12
0,12
0,23
0,1
0,38
0,38
0,73
1
1,2
1,2
2,3
10
3,8
3,8
7,3
100
12
12
23
For transmitters rated at a maximum output power not listed above, the recommended separation
distance d in metres (m) can be estimated using the equation applicable to the frequency of the
transmitter, where p is the maximum output power rating of the transmitter in watts (W) according to
the transmitter manufacturer.
NOTE1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reflection from structures, objects and people.
Specification
Model
2PQ6
Weight
Measurement
Capacity
180kg / 396lb
Weight Unit
Approximately 2.3Kg
LCD Display
45.4mm*121mm ( Included 4pcs icons)
LED dot matrix 40x12
Platform Dimension
'Φ14.2" x 1.3"(Φ360mm x 33.5mm)
Power Supply
4AA batteries
Operation Temperature,
Humidity
and air pressure
5℃~35℃ ( 41°F ~ 95°F)
30% / 85% RH
80~105KPa
Storage/transportation Temperature,
Humidity
and air pressure
-20℃~60℃ (-4°F ~ 140°F)
10% / 95 % RH
50~105KPa
Expected Service Life 20 months
Dust / Waterproof level
IP21
Battery Lift Approximately 6 months
(When 4 people use 2 times per day)
Note: Specifications are subject to change without prior notice.
Intended use description:
Helping consumers to keep a healthy balance between fat, calories and energy and
maintain a fit and healthy body.
How calculates your body composition:
Algorithm focuses on the Bioelectrical Impedance Method as well as height, weight, age and gender.
WARNING
Pregnant women and young children do not use this device.
Do no use, or allow others to use, this monitor I fitted with a cardiac pacemaker or other implanted medical device.
Manufacturer’s Declaration of Conformity
FCC CLASS B Declaration of Comformity
This device complies with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Manufactured by:
Krell Precision (Yang Zhou)Co.,Ltd
NO.28 XingYang Road,Development Area,
YangZhou City ,JiangSu Province.
FDA no.: XXXXXXX / XXXXXXXXXX
Proprietary Notice
© 2014-2015 HTC Corporation. All rights reserved. HTC, the HTC logo, and all other HTC product and service names
are the trademarks or registered tradmarks in the U.S. ans/or other countries of HTC Corporation and its affiliates.
91H0XXXX-XXM Rev.A
htc.com

Navigation menu