Contents
- 1. Manual
- 2. Users Manual
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2462000 |
| Application ID | ZK87WW7h5rXz0VrA3p2Ktw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 169.78kB (2122280 bits) |
| Date Submitted | 2014-12-03 00:00:00 |
| Date Available | 2014-12-03 00:00:00 |
| Creation Date | 2014-12-03 09:35:16 |
| Producing Software | doPDF Ver 7.3 Build 387 (Windows 7 Home Premium Edition (SP 1) - Version: 6.1.7601 (x64)) |
| Document Lastmod | 0000-00-00 00:00:00 |
| Document Title | Users Manual |
User's Manual SPP-R200II Mobile Printer Rev. 1.00 http://www.bixolon.com SPP-R200II ■ Table of Contents ※ Manual Information & Usage Precautions ······································· 3 1. Content Confirmation ·································································· 10 2. Product Part Names ···································································· 11 3. Installation & Usage ···································································· 12 3-1 Battery Installation ································································ 12 3-2 Battery Charging ·································································· 12 3-2-1 Battery Charging Usage ··················································································· 12 3-2-2 Cigarette Lighter Jack Charger (Optional) Usage ················································· 13 3-2-3 Using Quad Charger/Quad Cradle (Optional)························································ 14 3-3 Paper Installation·································································· 16 3-4 Using Car Holder (Optional) ··················································· 17 3-5 Control Panel Usage ····························································· 18 3-6 MSR Usage ········································································· 19 4. Self-Test ····················································································· 19 5. Label Printing Function ······························································· 22 5-1 Label Function Setting ··························································· 22 5-2 Auto Calibration Function ······················································· 22 6. Peripherals Connection ······························································· 23 6-1 Bluetooth Connection ···························································· 23 6-2 Interface Cable Connection ···················································· 23 7. Printer Cleaning ·········································································· 24 8. Appendix ···················································································· 25 8-1 Specifications ······································································ 25 8-2 Certification ········································································· 26 8-3 Label Types········································································· 27 Rev. 1.00 -2- SPP-R200II ■ Manual Information ※ Manual Information & Usage Precautions This user’s manual contains basic information for product usage as well as for emergency measures that may be required. ※ The following separate manuals provide more detailed content on various technological issues and areas. 1. Windows CE Module Program Manual This manual provides information on the dll files required for Windows CE application program development. 2. Windows Driver Manual This manual provides information on installation and main functions of the Windows Driver for this product. 3. Unified Utility Manual This manual provides information on the software used to select functions of this product, modify operation conditions, etc. • VMSM (Virtual Memory Switch Manager) : As a function that sets the basic operation conditions of the product, the use of non-hardware control, software-based virtual switches is explained. • NV Image Download Manager : The downloading of image files, such as logos, intended for repetitive printing is explained. • Firmware Download Manager : The downloading and installation of the latest Firmware, which is subject to ongoing modification for the enhancement of product performance, are explained. 4. Bluetooth Connection Manual This manual provides information on the connection of this product with devices equipped with Bluetooth functionality (PDAs, PCs, etc.). The devices included are as follows. • PDAs: - Intermec PDA (Device: CN2B, OS: Pocket PC 4.20.0) - SYMBOL PDA (Device: SYMBOL MC70, OS: Windows Mobile 5.0) - HP PDA (Device: iPAQ hx2700, OS: Windows Mobile 5.1.1702) - Mobile Compia PDA (Device: M3, OS: WinCE 5.0) - InnoTeletek PDA (Device: MC3000, OS: WinCE 4.2) - Widefly PDA (Device: WF35, OS: WinCE 5.0) • Bluetooth: - Dongle (BlueSoleil IVT Stack) - Dongle (Widcomm Stack) 5. Commands Manual This manual provides information on the protocol and functions of the control commands that can be used with this product. 6. Code Pages Manual This manual provides information on each character code page that can be used with this product. We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality of all our products. In following, product specifications and/or user manual content may be changed without prior notice. Rev. 1.00 -3- SPP-R200II ■ Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. WARNING Violating following instructions can cause serious injury or death. Do not plug several products in one multi-outlet. You must use only the supplied adapter. • • • • • It is dangerous to use other adapters. This can provoke over-heating and a fire. If the plug is wet or dirty, dry or wipe it before usage. If the plug does not fit perfectly with the outlet, do not plug in. Be sure to use only standardized multi-outlets. ONLY SUPPLIED ADAPTER PROHIBIT PROHIBIT Do not pull the cable to unplug. Keep the plastic bag out of children’s reach. • This can damage the cable, which is the origin of a fire or a breakdown of the printer. • If not, a child may put the bag on his head. PROHIBIT Do not plug in or unplug with your hands wet. • You can be electrocuted. PROHIBIT Do not bend the cable by force or leave it under any heavy object. • A damaged cable can cause a fire. PROHIBIT Rev. 1.00 PROHIBIT -4- SPP-R200II CAUTION Violating following instructions can cause slight wound or damage the appliance. If you observe a strange smoke, odor or noise from the printer, unplug it before taking following measures. Keep the desiccant out of children’s reach. • If not, they may eat it. • Switch off the printer and unplug the set from the mains. • After the disappearance of the smoke, call your dealer to repair it. TO UNPLUG PROHIBIT PRINTER Install the printer on the stable surface. • If the printer falls down, it can be broken and you can hurt yourself. Use only approved accessories and do not try to disassemble, repair or remodel it for yourself. • Call your dealer when you need these services. • Do not touch the blade of auto cutter. PRINTER DISASSEMBLING PROHIBITED PROHIBIT PRINTER Do not let water or other foreign objects in the printer. Do not use the printer when it is out of order. This can cause a fire or an electrocution. • If this happened, switch off and unplug the printer before calling your dealer. • Switch off and unplug the printer before calling your dealer. PROHIBIT TO UNPLUG PRINTER PRINTER DEALER Rev. 1.00 -5- SPP-R200II ■ Battery Safety Precautions Make sure to review the user manual carefully prior to product use. Neglecting to heed the following instructions can result in battery overheating, combustion, explosion, damage and/or decline in performance and product life. Danger 1. Do not allow water, seawater or moisture to enter or leak into the battery. If the safety mechanism within the battery becomes oxidized, the battery may overcharge with abnormal electrical current and/or voltage so that it may overheat, ignite and/or explode. 2. Do not place the battery near open flames or heating devices, such as stoves. Exposure to excessive heat may cause damage to the resin case and/or insulating materials, thus causing a short circuit within the battery that may result in battery overheating, combustion, and/or explosion. 3. Charge the battery only with the exclusive charger specified (optionally provided) by BIXOLON. The use of an incorrect charger may result in overheating, combustion and/or explosion of the battery. 4. Charging the battery with a modified charger may result in overheating, combustion and/or explosion of the battery by abnormal chemical reaction caused by incorrect polarity. 5. Do not directly connect the battery to an electrical power outlet not specified by BIXOLON or an automobile’s cigarette lighter jack. Doing so may result in overheating, combustion and/or explosion of the battery by over-current and/or over-voltage. 6. Do not heat the battery or place it near a fire. Doing so may melt insulation materials, damage the safety mechanism/equipment, and/or ignite the electrolytic solution. There is a potential risk of battery overheating, combustion, and/or explosion. 7. Do not reverse the connection of (+) and (-) electrodes of the battery. Charging the battery in reverse polarity may produce an undesired chemical reaction inside the battery cell, causing unexpected behavior during discharging such as overheating, explosion, or fire. 8. Do not allow the battery’s (+) or (-) pole to come into contact with any metal. In addition, do not carry or store the battery with metallic items, such as necklaces and hairpins. Doing so may cause a short circuit of the battery generating an over-current. There is the potential risk to overheat, ignite and/or explode the battery or overheat the metallic items, such as necklaces, hair pins etc. 9. Do not throw the battery or subject it to strong shock. If the safety mechanism in the battery is damaged, the battery may be overcharged and, consequently, an adverse chemical reaction may be generated in the battery. There is a potential risk of battery overheating, combustion, and/or explosion. Rev. 1.00 -6- SPP-R200II 10. Do not pierce the battery with a pointed object, such as nail or awl, or strike with a heavy object, such as a hammer, and take care not to step on the battery. There is a potential risk of battery overheating, combustion, and/or explosion caused by an internal short circuit. 11. Do not solder the battery directly. Doing so may melt the insulating materials and/or damage the safety mechanism or safety equipment, resulting in battery overheating, combustion, and/or explosion. 12. Do not disassemble and/or modify the battery. The battery contains safety equipment and a safety mechanism to prevent danger. There is a potential risk of overheating, combustion, and/or explosion caused by disassembly. 13. Do not charge the battery near open flames and/or under direct sunlight. Because exposure to high temperatures triggers the operation of the safety mechanism, the battery may not charge or may overcharge due to destruction of the safety mechanism. There is a potential risk of overheating, combustion, and/or explosion. 14. Do not expose the battery to high temperatures over 60 oC, and do not use or store it in a hot or humid place. 15. Do not use the battery if it is damaged or the exterior is deformed due to external shock or if it is swollen. Warning 1. Do not place the battery within the reach of small children to prevent any swallowing accidents. If a small child has swallowed the battery, consult a physician immediately. 2. Do not place the battery in a microwave oven and/or high voltage appliance. Doing so can cause rapid overheating and/or destruction of the sealing, resulting in battery overheating, combustion, and/or explosion. 3. Do not combine and use any battery of different capacity and/or type with the primary battery. Doing so can cause excessive electrical discharge during use or excessive charging during charging, resulting in an abnormal chemical reaction within the battery that can cause battery overheating, combustion, and/or explosion. 4. If during battery usage, storage, or charging, a strange odor or conditions differing from the normal, such as overheating, color changes, warping, etc., are detected, remove the battery from the product or charger and discontinue use. Continued use may cause battery overheating, combustion, and/or explosion. 5. When recharging, if the battery is not charged after the normal fixed charging time, discontinue charging. Continued charging can result in battery overheating, combustion, and/or explosion. 6. If the battery appears to be coated with condensation or emits a strange odor, immediately place it far away from any heat source. The condensation may be caused by a leak of electrolytic solution that can ignite to cause battery combustion and/or explosion. Rev. 1.00 -7- SPP-R200II 7. If the battery is leaking electrolytic solution and any of the solution enters the eyes, immediately wash out with clean water, and then consult a physician to receive treatment. Neglecting to do so can cause permanent eye injuries. Caution 1. Do not use or leave the battery in a location exposed to high temperatures or intense direct sunlight, such as within an automobile. Doing so can cause battery overheating and/or combustion. In addition, battery performance and product life may be reduced. 2. The battery contains a safety mechanism to prevent danger. Do not use the battery in a location that is prone to static electricity (above the amount covered by the manufacturer’s product warranty) that can cause damage to this safety mechanism. Damage to the safety mechanism can result in battery overheating, combustion, and/or explosion. 3. The temperature ranges for battery usage are as follows. Any usage outside of these ranges can result in battery overheating and/or damage. In addition, battery performance and product life may be reduced. - Charging: 0 ~ 40 oC - Product Usage: -20 ~ 60 oC - Storage: -20 ~ 60 oC (30 days) - Long-Term Storage: -20 ~ 40 oC (90 days) 4. Please review the exclusive charger manual carefully for charging instructions. 5. If you observe any abnormal symptom, such as strange smell and overheating, on first use after purchasing the product, contact your local dealer immediately. 6. If a child must use the battery, the child’s parent or legal guardian should clearly explain the instructions from the user manual prior to use. In addition, the parent or legal guardian should periodically confirm that usage is being conducted in accordance with user manual instruction during use. 7. Store the battery in a location that is out of the reach of small children. During usage, make sure to also place the charger and/or product out of the reach of small children. 8. If the battery is leaking electrolytic solution, and the solution comes in contact with the skin or clothing, immediately wash thoroughly with clean water. Contact with skin can result in skin disorders. 9. Make sure to review the user manual and precautions carefully prior to use. In addition, after carefully reviewing the user manual and precautions, place them in a secure location for future reference when needed. 10. There is a risk of explosion when replacing with an incorrect battery. Only exchange it for another one of the same or equivalent model specified by BIXOLON. Insulate the used battery by attaching insulation tape to its port, and then dispose of the battery according to local regulations. 11. If using the printed side of preprinted paper, this may cause malfunction. Rev. 1.00 -8- SPP-R200II Recommended 1. Review the user manual for instructions concerning insertion/removal of batteries into/from the product. 2. The battery shipped with the product is partially charged, and it is good for checking the operation of the equipment. Charge the battery first with the supplied charger if the equipment does not work or long hours of operation are required. 3. To avoid improper use of the battery, review the product user manual carefully. 4. Do not charge the battery for long times in excess of the normal charging time indicated in the user manual. 5. If the battery is not to be used for a long period of time, remove it from the product and store in a location with low humidity. If the battery is stored while still inserted in the product in a highly humid location, oxidization may occur along with a decline in battery performance. 6. Turn off the power after using the equipment. Otherwise the performance of the battery will be degraded over time. 7. The battery may fail to charge if it is not used for a long period of time. Charge the battery with the supplied charger at least once every six months if the equipment is not used for a long time. Leaving the battery for a long time without charging may degrade the performance of the battery or cause system trouble. 8. If the battery terminal is contaminated, clean the contact with a dry cloth before using it. Using the battery with contaminated contacts may cause problems when supplying power to the equipment or charging due to irregular electric contact. 9. Each battery has a life cycle. If the usage time of the produce is shortened, replace with a new battery. Insulate the used battery by attaching insulation tape to its port, and then dispose of the battery according to local regulations. ■ Other Precautions The copyright for this user manual and various other manuals is property of the BIXOLON Co., Ltd. Any copying or conversion into electronic firm and saving of this material without the express written permission of BIXOLON Co., Ltd. is strictly prohibited. Use of the information contained in this manual is not subject to any patent liability. This manual has been prepared with utmost care and attention to detail but may contain certain errors and/or omissions. BIXOLON Co., Ltd. is not legally liable for any damages resulting from the use of the information in this manual. BIXOLON Co., Ltd. and its affiliates are not legally liable (United States excluded) for any damages, loss, costs, and/or expenses that result from the breakdown, malfunction, and/or misuse of the product due to violation or neglect of the operation and maintenance information and instructions provided by the BIXOLON Co., Ltd., as well as from the unauthorized alteration, repair, and/or modification of the product by the user and/or third party. BIXOLON Co., Ltd. is not legally liable for any damages and/or issues resulting from the use of options and/or parts that are not authentic BIXOLON products or authorized products. Rev. 1.00 -9- SPP-R200II 1. Content Confirmation The following items should all be contained in the printer package. Contact the dealer from which the purchase was made if any item is damaged and/or missing. ※ Basic items SPP-R200II Battery Battery Charger Power Cord User Manual CD Paper ※ Optional items Car Holder Battery Rev. 1.00 Interface Cable Cigarette Lighter Jack Charger Quad Cradle Quad Charger - 10 - Cleaning Pen Wall mount forQuad Charger(RWM-350) SPP-R200II 2. Product Part Names • Front Paper Cover Power Button Paper Feed Button Open Button MSR Cover • Rear Hole for mounting belt strap / belt clip Battery Interface Cap Cable Connection Power Connection Rev. 1.00 - 11 - SPP-R200II 3. Installation & Usage 3-1 Battery Installation 1) Insert the battery on the rear side of the printer, aligning the battery hook properly. 2) Push the battery into the slot until a snapping sound is heard. NOTE As the battery is not charged at the time of purchase, charge the battery prior to product use. (Use the battery charger) 3-2 Battery Charging 3-2-1 Battery Charging Usage 1) Turn off the printer power. 2) Connect the power cord ② to the battery charger ①, and then connect AC power. ③ ① ② 3) Open the external interface cap in the direction of ③. 4) Connect the battery charger to the power connector. CAUTION The printer may incur serious damage if the battery charger provided by BIXOLON is not used. BIXOLON is not legally liable for any such damages. (The voltage and electrical current specifications of the printer and battery charger must match.) WARNING Turn off the power before charging the battery for the printer. Rev. 1.00 - 12 - SPP-R200II 3-2-2 Cigarette Lighter Jack Charger (Optional) Usage 1) Turn off the power to the printer. 2) Connect the cigarette lighter jack charger ① to your car’s cigarette lighter jack. 3) Open the external interface protection cap in the direction of ②. ① 4) Connect the battery charger to the power connector. ② CAUTION The printer may be seriously damaged if a battery charger not provided by BIXOLON is used. BIXOLON is not liable for such damage. WARNING Turn off the power before charging the battery for the printer. Rev. 1.00 - 13 - SPP-R200II 3-2-3 Using Quad Charger/Quad Cradle (Optional) 3-2-3-1 Connecting the cables 1) Connect the power cord to the adaptor, and Connect the adaptor to the power connector of the Quad Charger. 2) Plug the power cord into a power Outlet. Input power is 100 ~ 240VAC, 50/60Hz, 1.4A. 3) When power is supplied, the amber and green Lamp turn on for two seconds. WARNING Use only designated AC/DC adaptor. (12VDC, 5A) Rev. 1.00 - 14 - SPP-R200II 3-2-3-2 Charging Battery (Printer) 1) Fasten batteries via the battery hooks into the Quad Charger as shown above. 2) Push the battery in until a snapping sound is emitted. 3) Charging begins as soon as the battery is completely inserted. Batteries are charged to 8.4VDC, 0.8A. 4) Push the hook and pull up to extract the battery. 1) Turn the printer off. 2) Slide the printer in the Quad Cradle as shown in the picture. 3) Push the printer in until a clicking sound is heard. 4) Charging will begin when the printer is installed. 5) Pull out the printer to separate it. NOTE Battery charging status descriptions are as follows. Lamp Charge Status Red Lamp On Charging Green Lamp Blinking Over 80% Charged Green Lamp On Fully Charged Error Replace or Reinstall Battery Red Lamp Blinking Charge Time 2.5 hours CAUTION 1. If the red lamp of the charger blinks, install the battery again. 2. If the red lamp continues to blink despite several attempts (4 ~ 5 times) to install the battery, contact your local dealer. 3. The charging time may vary depending on the type of the charger or ambient temperature. Rev. 1.00 - 15 - SPP-R200II 3-3 Paper Installation 1) Press the Open button to open the paper cover. 2) Insert the paper as shown in the image. (Remove any remaining core of a fully used paper roll.) 3) Take care to align the paper correctly. 4) Pull the paper out as shown in the image and close the paper cover. 5) Tear off any excess paper in the direction of the side of the printer. Rev. 1.00 - 16 - SPP-R200II 3-4 Using Car Holder (Optional) 1) Assemble the car holder to the mount. 2) Adjust the car mount properly, put the suction plate close to the glass, and pull the level to fix the position. (Use the disk pad to mount it on the dash board) 3) Slide the printer in the car holder completely as shown in the picture. Rev. 1.00 - 17 - SPP-R200II 3-5 Control Panel Usage • Power Button This button is used to turn the printer on and off. When the printer is off, pressing this button for approximately 2 seconds will turn the power on. When the printer is on, pressing this button for approximately 2 seconds will turn the power off. • Paper Feed Button This button is used to feed paper manually, take the self-set and dump hexadecimals. 1) To feed paper manually, press this button. 2) For information on the self-test, refer to “4. Self-Test”. 3) For information on the dump of hexadecimals, refer to “Service Manual”. • Battery Status Lamp (Blue or Red) 1) If three blue lamps are lit, the battery is fully charged. 2) If two blue lamps are lit, the battery is half charged. 3) If one blue lamp is lit, the battery is at the lowest charge level. 4) If the red lamp is lit, the battery must be charged or replaced. • Error Lamp (Left-sided) 1) If the red lamp is lit, the paper cover is open. 2) If the red lamp is blinking, either the paper has been fully used or the print head is overheated. (Fill with paper or turn the printer off for at least 10 minutes.) 3) If the red lamp continues to blink, it may indicate a more serious problem with the product, and thus an authorized service dealer should be consulted. • Bluetooth Lamp (Green) 1) When using Bluetooth If the printer is ready for wireless communication with any Bluetooth, the green lamp as well as the battery status lamp is turned on. 2) When using wireless LAN The right indicator shows the signal strength from wireless LAN. The green lamp blinks for acceptable signal strength while the red lamp blinks for weak signal strength. In power save mode, only the Status lamp is lit. NOTE The power saving mode is activated after the first communication, with the Rev. 1.00 - 18 - SPP-R200II default time interval being 10 seconds. 3-6 MSR Usage 1) Press the MSR cover to open. 2) Insert the card as shown in the image and swipe in the direction of the arrow. (can be done in both directions) 3) When finished using, press the MSR cover to close it. NOTE If the card does not register, first check to see if it is properly aligned. When swiping the card, the recommended swiping speed is 100 ~ 1200 mm/sec. 4. Self-Test Run the self-test when first setting the printer or when encountering a problem, and check the following. - Control Circuit, Mechanisms, Print Quality, ROM Version, and Memory Switch Settings If no issue is found with the printer after running the self-test, examine the other devices or peripherals and software. This function is independent of such other devices and software. • Self-Test Instructions 1) Turn the printer power off and close the printer paper cover. 2) Pressing the paper feed button and power button simultaneously turns the printer on. 3) The printout is produced after releasing the two buttons. 4) To add a printout of the ASCII pattern, press the paper feed button once more. 5) After the ASCII pattern is printed out, the self-test is automatically terminated. Rev. 1.00 - 19 - SPP-R200II • Self-Test Sample (For Bluetooth) Firmware version : V01.00 STOB 050412 Butter Capacity : 128K Bytes Print Density : 100% Serial Interface - Baud rate : 115200 bps Data bits : 8 bits Parity : None Stop bit : 1 bit or more Handshaking : DTR/DSR Default Codepage : PC437 Print Speed : Max. 80mm/s Double byte character mode:On Font : 12 x 24 Paper out Bell : Off Low Battery Buzzer : On Power off time : 15 Min Idle mode time : 10 Sec MSR data including sentinel Character mode : None MSR read mode : Auto TRACK1/2/3 BATT NTC : OK If you want to continue SELF-TEST printing, Please press FEED button. ASCII !”#$%&’()*+, -./ 0123456789:; <=>?@ ”#$%&’()*+,-./0123456789:;<=>?@A #$% & ’ ()*+, -. / 0123456789: ; <=>?@A B $% &’ ()*+, -. / 0123456789:; <=>?@AB C %&’ ()* +, -./ 0123456789:; <= > ?@AB CD & ’()*+, -./ 0123456789: ; <=>?@A B CDE ’()*+,-./0123456789:;<=>?@ABCDEF ()* +,-./0123456789:;<= >?@AB CDEFG )*+,-./0123456789:;<=>?@ABCDEFGH *+,-./0123456789:;<=>?@ABCDEFGHI + , - ./ 0 1 2 3 4 5 6 7 8 9 : ; <= > ? @A B CDE F G HI J , -./ 0123456789:; < = > ?@AB CDE FGHIJ K -./0 1 2 34 5 67 8 9:;< = >? @A B CD EF G HIJKL ./0123456789:;<=>?@ABCDEFGHIJKLM / 0 12 3 4 56 7 8 9: ; < = >? @ A B C DE F G HI J K L M N 012345 6789: ; <=>? @A B CDE FGHI J K LM NO 123456789: ; <=>?@A B CDE FGHI J K LMNOP 23456789:; <=>?@AB CDEFGHI JK LMNOP Q 3456789:; <=>?@AB CDEFGHIJK LMNOPQR 456789:;<=>?@AB CDEFGHIJK LMNOPQRS 56789:;<=>?@ABCDEFGHIJKLMNOPQRST 6789:;<=>?@ABCDEFGHIJKLMNOPQRSTU 789:;<=>?@ABCDEFGHIJKLMNOPQRSTUV 89:;<=>?@ABCDEFGHIJKLMNOPQRSTUVW 9:;<=>?@ABCDEFGHIJKLMNOPQRSTUVW X Memory switch setup status Memory S/W1 Memory S/W2 1 23 45 6 78 1 23 45 6 78 ON █ █ ON OFF █ █ █ █ █ █ OFF █ █ █ █ █ █ █ █ Memory S/W3 1 23 45 6 78 ON █ █ █ █ OFF ████ Memory S/W4 1 23 45 6 78 ON OFF █ █ █ █ █ █ █ █ Memory S/W5 1 23 45 6 78 ON █ █ █ █ OFF ████ Memory S/W6 1 23 45 6 78 ON █ █ OFF█ █ █ █ █ █ Memory S/W7 1 23 45 6 78 ON ███ OFF █ █ █ █ █ Memory S/W8 1 23 45 6 78 ON OFF █ █ █ █ █ █ █ █ PC437 Çüé âä àåçê ëèïîìÄÅÉæÆôöò ûùÿÖ Ü¢ £¥ Ptƒ üé âä à åçê ëèïîìÄÅÉæÆ ô öò ûùÿ Ö Ü¢ £¥ Pt ƒá éâäàåç êëèïî ìÄÅÉ æÆ ôöòûùÿ ÖÜ¢£¥ P t ƒáí âäàåçêëèïî ìÄÅ Éæ Æôöòûùÿ ÖÜ¢£¥ P t ƒáíó äàåç êëèï îìÄÅ Éæ Æ ôöòûùÿ ÖÜ¢ £¥Pt ƒáí óú àåç êëèïîìÄ ÅÉæ Æ ôöòûùÿ ÖÜ¢£¥ Pt ƒáí óúñ åçêëèïîìÄÅÉæ Æ ôöòûùÿ ÖÜ¢£¥ Pt ƒáíóúñÑ ç êëèïîì ÄÅÉ æÆ ôöòûùÿ ÖÜ¢£¥ P t ƒáí óúñѪ êëèï îìÄ ÅÉ æ Æ ôöòûùÿ ÖÜ¢£¥ P t ƒáí óúñѪº ëèïî ìÄ ÅÉæ Æ ôöòûùÿ ÖÜ¢£¥ P t ƒáí óúñѪº¿ èïîìÄ ÅÉæ Æ ôöòûùÿ Ö Ü¢£¥ P t ƒáí óúñѪº¿┌ ï îì ÄÅÉæ Æôöòûùÿ ÖÜ¢£¥Ptƒáí óúñѪº¿┌ ┐ î ì Ä Å É æ Æôö òû ùÿ Ö Ü¢ £¥ Pt ƒáí óú ñÑ ª º¿ ┌ ┐½ ì ÄÅ Éæ Æôöòûùÿ ÖÜ¢£¥Ptƒáí óúñѪº¿ ┌ ┐½ ¼ Ä ÅÉ æÆôöòûùÿ ÖÜ¢£¥Ptƒáí óúñѪº¿ ┌ ┐½ ¼ ¡ Å É æÆôöòûùÿ ÖÜ¢£¥Ptƒáí óúñѪº¿ ┌ ┐½ ¼ ¡« É æ Æôöòûùÿ ÖÜ¢£¥Ptƒáí óúñÑ ªº¿ ┌ ┐½ ¼ ¡«» æ Æôöòûùÿ ÖÜ¢£¥Ptƒáí óúñѪº¿ ┌ ┐½ ¼ ¡«»▓ Æôöòû ùÿ ÖÜ¢£ ¥Ptƒ áí óúñÑ ªº¿ ┌ ┐½ ¼ ¡« »▓ ▒ ôö òû ùÿ Ö Ü¢ £¥ Pt ƒ áí ó úñ Ñ ªº¿ ┌ ┐½ ¼ ¡« »▓ ▒░ öòûùÿ ÖÜ¢£¥Ptƒáí óúñÑ ªº¿ ┌ ┐½ ¼ ¡«»▓ ▒░ ┃ òûùÿ ÖÜ¢£¥Ptƒáí óúñѪº¿┌ ┐½ ¼ ¡«»▓ ▒░┃ ┤ ûùÿ ÖÜ¢£¥PtƒáíóúñѪº¿┌ ┐½ ¼ ¡«»▓▒░┃┤╡ ùÿÖ Ü ¢£¥Ptƒáí óúñ Ѫ º¿ ┌ ┐½ ¼ ¡«»▓ ▒░┃ ┤╡╢ ÿ ÖÜ¢£¥Ptƒáí óúñѪº¿┌┐½ ¼ ¡«»▓ ▒░ ┃ ┤╡╢╖ RF Interface Bluetooth Firmware version : 4.0.0 Bluetooth BD address : 001901223194 - Auth. & Encry. are enable - Connection Mode = 2 Not available WLAN *** Completed *** Rev. 1.00 - 20 - SPP-R200II • Self-Test Sample (For Wireless LAN) Firmware version : V01.00 STOB 050412 Butter Capacity : 128K Bytes Print Density : 100% Serial Interface - Baud rate : 115200 bps Data bits : 8 bits Parity : None Stop bit : 1 bit or more Handshaking : DTR/DSR Default Codepage : PC437 Print Speed : Max. 80mm/s Double byte character mode:On Font : 12 x 24 Paper out Bell : Off Low Battery Buzzer : On Power off time : 15 Min Idle mode time : 10 Sec MSR data including sentinel Character mode : None MSR read mode : Auto TRACK1/2/3 BATT NTC : OK If you want to continue SELF-TEST printing, Please press FEED button. ASCII !”#$%&’()*+, -./ 0123456789:; <=>?@ ”#$%&’()*+,-./0123456789:;<=>?@A #$% & ’ ()*+, -. / 0123456789: ; <=>?@A B $% &’ ()*+, -. / 0123456789:; <=>?@AB C %&’ ()* +, -./ 0123456789:; <= > ?@AB CD & ’()*+, -./ 0123456789: ; <=>?@A B CDE ’()*+,-./0123456789:;<=>?@ABCDEF ()* +,-./0123456789:;<= >?@AB CDEFG )*+,-./0123456789:;<=>?@ABCDEFGH *+,-./0123456789:;<=>?@ABCDEFGHI + , - ./ 0 1 2 3 4 5 6 7 8 9 : ; <= > ? @A B CDE F G HI J , -./ 0123456789:; < = > ?@AB CDE FGHIJ K -./0 1 2 34 5 67 8 9:;< = >? @A B CD EF G HIJKL ./0123456789:;<=>?@ABCDEFGHIJKLM / 0 12 3 4 56 7 8 9: ; < = >? @ A B C DE F G HI J K L M N 012345 6789: ; <=>? @A B CDE FGHI J K LM NO 123456789: ; <=>?@A B CDE FGHI J K LMNOP 23456789:; <=>?@AB CDEFGHI JK LMNOP Q 3456789:; <=>?@AB CDEFGHIJK LMNOPQR 456789:;<=>?@AB CDEFGHIJK LMNOPQRS 56789:;<=>?@ABCDEFGHIJKLMNOPQRST 6789:;<=>?@ABCDEFGHIJKLMNOPQRSTU 789:;<=>?@ABCDEFGHIJKLMNOPQRSTUV 89:;<=>?@ABCDEFGHIJKLMNOPQRSTUVW 9:;<=>?@ABCDEFGHIJKLMNOPQRSTUVW X Memory switch setup status Memory S/W1 Memory S/W2 1 23 45 6 78 1 23 45 6 78 ON █ █ ON OFF █ █ █ █ █ █ OFF █ █ █ █ █ █ █ █ Memory S/W3 1 23 45 6 78 ON █ █ █ █ OFF ████ Memory S/W4 1 23 45 6 78 ON OFF █ █ █ █ █ █ █ █ Memory S/W5 1 23 45 6 78 ON █ █ █ █ OFF ████ Memory S/W6 1 23 45 6 78 ON █ █ OFF█ █ █ █ █ █ Memory S/W7 1 23 45 6 78 ON ███ OFF █ █ █ █ █ Memory S/W8 1 23 45 6 78 ON OFF █ █ █ █ █ █ █ █ PC437 Çüé âä àåçê ëèïîìÄÅÉæÆôöò ûùÿÖ Ü¢ £¥ Ptƒ üé âä à åçê ëèïîìÄÅÉæÆ ô öò ûùÿ Ö Ü¢ £¥ Pt ƒá éâäàåç êëèïî ìÄÅÉ æÆ ôöòûùÿ ÖÜ¢£¥ P t ƒáí âäàåçêëèïî ìÄÅ Éæ Æôöòûùÿ ÖÜ¢£¥ P t ƒáíó äàåç êëèï îìÄÅ Éæ Æ ôöòûùÿ ÖÜ¢£¥ Pt ƒáí óú àåç êëèïîìÄ ÅÉæ Æ ôöòûùÿ ÖÜ¢£¥ Pt ƒáí óúñ åçêëèïîìÄÅÉæ Æ ôöòûùÿ ÖÜ¢£¥ Pt ƒáíóúñÑ ç êëèïîì ÄÅÉ æÆ ôöòûùÿ ÖÜ¢£¥ P t ƒáí óúñ Ѫ êëèï îìÄ ÅÉ æ Æ ôöòûùÿ ÖÜ¢£¥ P t ƒáí óúñѪº ëèïî ìÄ ÅÉæ Æ ôöòûùÿ ÖÜ¢£¥ P t ƒáí óúñѪº¿ èïîìÄ ÅÉæ Æ ôöòûùÿ Ö Ü¢£¥ P t ƒáí óúñѪº¿┌ ï îì ÄÅÉæ Æôöòûùÿ ÖÜ¢£¥Ptƒáí óúñѪº¿┌ ┐ î ì Ä Å É æ Æôö òû ùÿ Ö Ü¢ £¥ Pt ƒáí óú ñÑ ª º¿ ┌ ┐½ ì ÄÅ Éæ Æôöòûùÿ ÖÜ¢£¥Ptƒáí óúñѪº¿ ┌ ┐½ ¼ Ä ÅÉ æÆôöòûùÿ ÖÜ¢£¥Ptƒáí óúñѪº¿ ┌ ┐½ ¼ ¡ Å É æÆôöòûùÿ ÖÜ¢£¥Ptƒáí óúñѪº¿ ┌ ┐½ ¼ ¡« É æ Æôöòûùÿ ÖÜ¢£¥Ptƒáí óúñÑ ªº¿ ┌ ┐½ ¼ ¡«» æ Æôöòûùÿ ÖÜ¢£¥Ptƒáí óúñѪº¿ ┌ ┐½ ¼ ¡«»▓ Æôöòû ùÿ ÖÜ¢£ ¥Ptƒ áí óúñÑ ªº¿ ┌ ┐½ ¼ ¡« »▓ ▒ ôö òû ùÿ Ö Ü¢ £¥ Pt ƒ áí ó úñ Ñ ªº¿ ┌ ┐½ ¼ ¡« »▓ ▒░ öòûùÿ ÖÜ¢£¥Ptƒáí óúñÑ ªº¿ ┌ ┐½ ¼ ¡«»▓ ▒░ ┃ òûùÿ ÖÜ¢£¥Ptƒáí óúñѪº¿┌ ┐½ ¼ ¡«»▓ ▒░┃ ┤ ûùÿ ÖÜ¢£¥PtƒáíóúñѪº¿┌ ┐½ ¼ ¡«»▓▒░┃┤╡ ùÿÖ Ü ¢£¥Ptƒáí óúñ Ѫ º¿ ┌ ┐½ ¼ ¡«»▓ ▒░┃ ┤╡╢ ÿ ÖÜ¢£¥Ptƒáí óúñѪº¿┌┐½ ¼ ¡«»▓ ▒░ ┃ ┤╡╢╖ RF Interface Not available Bluetooth WLAN firmware version : Ver 1.2 WLAN MAC address : cc7a30020517 - System Name : SPP-R200II - Network Mode : Adhoc - Authentication : Open - Encryption : None - ESSID : BIXOLON_adhoc - DHCP : Disabled - IP : 192.168.1.1 - Netmask : 255.255.255.0 - Gateway : 192.168.1.2 - Port : 9100 - HTTPS : Disabled - Telnet : Disabled - FTP : Disabled - SNMP : Disabled *** Completed *** Rev. 1.00 - 21 - SPP-R200II 5. Label Printing Function 5-1 Label Function Setting Label paper and black mark paper available at the label mode. • Setting Operations 1) Turn on the printer power. 2) Open the paper cover and press and hold down the paper feed button for longer than two seconds. 3) After the buzzer tone is emitted, insert paper and close the cover. 4) Repeat the steps above to return to receipt mode. • Setting Via Memory Switch - Please refer to the memory switch changing section of the Commands Manual. 5-2 Auto Calibration Function The label printing function requires the recognition of label paper gaps and black mark paper black bar in order to print. If label paper gaps are not properly recognized, use the auto calibration function. • Auto Calibration Instructions 1) Turn the printer power off while in label print mode. 2) Press and hold down the paper feed button and then press the power button. 3) After the following printout is outputted, press the power button to perform auto calibration. Select the mode Auto Calibration: Power Button Self Test: Feed Button 4) Three pages of label paper are outputted when performing auto calibration. Rev. 1.00 - 22 - SPP-R200II 6. Peripherals Connection This product can communicate with other devices via Bluetooth communication and cable. 6-1 Bluetooth Connection 1) The printer can be connected to devices equipped with Bluetooth communication capacity (PDAs, PCs, etc.). 2) Use the Bluetooth connection function supported by the device to connect to the printer. 3) The printer can be connected to other stations, such as PDAs and PCs supporting wireless LAN communication in Ad-hoc mode and AP in Infrastructure mode. NOTE Refer to the Bluetooth Wireless LAN Manual for detailed information on its connection. You can check the bluetooth environment (authentication, encryption, connection mode) and the wireless LAN environment (IP, SSID, authentication, encryption) via the self-test page. 6-2 Interface Cable Connection 1) Open the Interface Cap ①. 2) Connect the interface cable (optional) ② to the cable connector of the printer. NOTE ① ② Use only cables (optional) provided by BIXOLON (USB, Serial). 3) Connect the interface cable to the USB port of the device (PDAs, PCs, etc.). NOTE The interface cable that can be connected with the printer is available in both USB and Serial type. Refer to the service manual for detailed interface cable specifications. Rev. 1.00 - 23 - SPP-R200II 7. Printer Cleaning If the interior of the printer is dusty, print quality can decline. In such a case, follow the instructions below to clean the printer. CAUTION • Make sure to turn the printer power off prior to cleaning. • As the print head gets very hot during printing, if intending to clean the print head, turn the printer power off and wait approximately 10 minute before commencement. • When cleaning the print head, take care not to touch the heated portion of the print head. → The print head is susceptible to damage from static electricity, etc. • Take care not to allow the print head to become scratched and/or damaged in any way. 1) Open the paper cover and remove any paper that may be present. 2) Wipe the print head with a cleaning pen. 3) Use a cloth moistened with an alcohol solution to clean the paper sensor are and remove any paper remnants and/or dust. 4) Insert paper into the printer 1~2 minutes after completing the cleaning process and close the printer cover. Rev. 1.00 - 24 - SPP-R200II 8. Appendix 8-1 Specifications Item Description Printing Method Printing Speed Resolution Paper Supply Mode Character Size Characters Per Line Character Set Printing Barcode Emulation Driver SDK Reliability Sensor Cutter Type Language Paper Type Width Diameter Thickness TPH Battery Communications Interface Paper Battery Charger Input Output Type Battery Output Charging Time Usage Conditions Temperature Humidity Dimensions Printer Weight Printer Basic Package Accessories Sold Separately Thermal printing 90 mm/sec (Receipt Paper) 203 DPI Easy paper loading Font A: 12 × 24 Font B: 9 × 17 Font A: 32 Font B/C: 42 Font C: 9 × 24 English: 95 Expanded Graphics: Standard(ENG) -128 × 30 pages Others(KOR,CHN,JPN) - 128 × 20 pages International: 32 1 Dimension: UPC A, UPC E, CODE 39, CODE 93, Code 128, EAN 8, EAN 13, ITF, Codabar 2 Dimension: PDF417, DATAMATRIX, MAXI, QR BXL/POS Windows XP(32bit) / WEPOS / 2003 Server(32bit) / VISTA(32bit) / 2008 Server(32bit) / 7 (32bit) Windows XP / WEPOS / 2003 Server / VISTA / 2008 Server / 7 / CE 3.0 and later Paper End, Paper Cover Open Tear-Bar User language supported Thermal paper 58 ± 0.5 mm (2.28” ± 0.2”) Max. ø40 mm (1.57”) 0.07 ± 0.003 mm 50 km Rechargeable up to 500 times Serial/USB, Bluetooth Class2 V3.0 Wireless Lan 802.11 b/g/n * Communication is enabled only for devices with Bluetooth or Wireless LAN function. Voltage: 100 ~ 250 VAC/100 ~ 240VAC Current: 0.5A (Max. at 110VA) Voltage: 8.4 VDC Current: 0.8A * Charging current and charging time may depend on the type (option) of the charger. Lithium-ion Voltage: 7.4 VDC (Available 8.4 ~ 6.8VDC) Capacity: 1200 mAh 2.5 hours Printer: -10~50℃ (14~122℉) Battery: 0~40℃ (32~104℉) Printer: 10~80% RH (No condensation) Battery: 20~70% RH(Non-condensing, refer to the tempera ture conditions on page 8) 79.5mm × 126.7mm × 43.6mm (3.13″ × 4.99″ × 1.72″) Printer : 186g (0.42lbs) Printer + Battery : 239g (0.53lbs) Printer + Battery + Paper : 296g (0.66lbs) Package: approx. 1000g (2.2lbs) Battery, Battery Charger, Belt Clip, Paper Battery, Case, Protection Case, Belt Strap, Cleaning Pen, Car Holder, Interface Cable, Cigarette Lighter Jack Charger, Shoulder Strap, Quad Cradle, Quad Charger, Wall mount for QuadCharger(RWM-350) * This equipment is indooruse and all the communication hiring are limited to inside of the building. * The switch is the disconnecting device. Turn off switch from any hazard. Rev. 1.00 - 25 - SPP-R200II 8-2 Certification 1) WEEE (Waste Electrical and Electric Equipment) This mark shown on the product or its literature indicates that the corresponding item should not be discarded at the end of its working life with other household waste. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate marked items from other types of waste and recycle them responsibly to promote the sustained reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office for details of where and how they can conduct environmentally safe recycling of such items. Commercial users should contact their suppliers and check the terms and conditions of purchase contracts. This product should not be combined with other commercial waste for disposal. 2) This equipment is indooruse and all the communication hiring are limited to inside of the building. 3) The switch is the disconnecting device. Turn off switch from any hazard. Warning Lithium-lon Battery packThe battery has the potential risk of overheating, fire and/or explosion. To avoid such risks, observe the following instructions: • A visibly swollen battery may be dangerous. Contact BIXOLON or your local dealer. • Only use an eligible charger. • Keep away from open flames. (Do not place in a microwave.) • Do not leave the battery pack inside a vehicle in summertime. • Do not store or use in a hot and humid place like a sauna with sleeping rooms. • Do not place the battery pack on a quilt, an electric blanket or a carpet for a long time. • Do not store the battery pack switched on in an enclosed place for a long time. • Do not allow the battery port to touch metal items, such as necklace, coin, key or clock etc. • Use the lithium secondary cell guaranteed by mobile phone manufacturer or BIXOLON. • Do not disassemble, compress or pierce the battery pack. • Do not drop the battery pack from a high place or subject it to strong shock. • Do not expose the battery to high temperatures over 60oC. • Do not expose to humidity. Disposal Directions • Do not dispose of waste battery packs recklessly. • Do not burn or throw in fire to dispose of the battery pack. There is a risk of fire and/or explosion. • How to dispose of battery packs may vary depending on countries or regions. Dispose of it in the correct method. Recommendation for Charging • Do not charge your battery pack in a way not mentioned in the instruction manual. Doing so may result in fire or explosion. Rev. 1.00 - 26 - SPP-R200II 8-3 Label Types The labels used on this product are composed of the following materials; • BIXOLON logo label: PC • Rating Label: PP • Other labels: PET FCC compliance Information This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Information to the user NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement : This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. Rev. 1.00 - 27 -
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 27 Page Layout : OneColumn Page Mode : UseNone Producer : doPDF Ver 7.3 Build 387 (Windows 7 Home Premium Edition (SP 1) - Version: 6.1.7601 (x64)) Create Date : 2014:12:03 09:35:16+09:00EXIF Metadata provided by EXIF.tools