Behringer Xenyx X1222Usb Users Manual

Behringer-Xenyx-X1222Usb-Owners-Manual behringer-xenyx-x1222usb-owners-manual

2015-06-29

: Behringer Behringer-Xenyx-X1222Usb-Users-Manual-752300 behringer-xenyx-x1222usb-users-manual-752300 behringer pdf

Open the PDF directly: View PDF .
Page Count: 16

Download
Open PDF In Browser	View PDF

User Manual

X1222
Premium 16-Input 2/2-Bus Mixer with XENYX Mic Preamps
& Compressors, British EQs, 24-Bit Multi-FX Processor and
USB/Audio Interface

XENYX X1222USB User Manual

Table of Contents
Thank you........................................................................ 2
Important Safety Instructions....................................... 3
Legal Disclaimer.............................................................. 3
Limited warranty............................................................. 3
1. Introduction................................................................ 4
1.1 General mixing console functions ................................ 4
1.2 The user’s manual................................................................ 5
1.3 Before you get started....................................................... 5
2. Control Elements and Connectors ........................... 5
2.1 Mono channels..................................................................... 5
2.2 Stereo channels.................................................................... 7
2.3 Connector panel and main section.............................. 7
2.4 Graphic 7-band equalizer............................................... 10
2.5 Rear view of X1222USB.................................................... 11
3. Digital Effects Processor and
XPQ Surround Function................................................ 11
3.1 Digital effects processor.................................................. 11
3.2 XPQ surround function................................................... 12
4. Installation................................................................ 12
4.1 Rack mounting.................................................................... 12
4.2 Cable connections............................................................ 12
5. Specifications............................................................ 13

Thank you
Congratulations! In purchasing the BEHRINGER XENYX you have acquired a
mixer whose small size belies its incredible versatility and audio performance.
The XENYX Series represents a milestone in the development of mixing console
technology. With the new XENYX microphone preamps including phantom power
as an option, balanced line inputs and a powerful effects section, the mixing
consoles in the XENYX Series are optimally equipped for live and studio
applications. Owing to state-of-the-art circuitry, your XENYX console produces
a warm analog sound that is unrivalled. With the addition of the latest digital
technology, these best-in-class consoles combine the advantages of both analog
and digital technology.

XENYX X1222USB User Manual

Important Safety
Instructions

Terminals marked with this symbol carry
electrical current of sufficient magnitude
to constitute risk of electric shock.
Use only high-quality professional speaker cables with
¼" TS or twist-locking plugs pre-installed. All other
installation or modification should be performed only
by qualified personnel.
This symbol, wherever it appears,
alerts you to the presence of uninsulated
dangerous voltage inside the
enclosure - voltage that may be sufficient to constitute a
risk of shock.
This symbol, wherever it appears,
alerts you to important operating and
maintenance instructions in the
accompanying literature. Please read the manual.
Caution
To reduce the risk of electric shock, do not
remove the top cover (or the rear section).
No user serviceable parts inside. Refer servicing to
qualified personnel.
Caution
To reduce the risk of fire or electric shock,
do not expose this appliance to rain and
moisture. The apparatus shall not be exposed to dripping
or splashing liquids and no objects filled with liquids,
such as vases, shall be placed on the apparatus.

9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Use only attachments/accessories specified by
the manufacturer.
12. Use only with the
cart, stand, tripod, bracket,
or table specified by the
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus
combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has
been dropped.
15. The apparatus shall be connected to a MAINS socket
outlet with a protective earthing connection.
16. Where the MAINS plug or an appliance coupler is
used as the disconnect device, the disconnect device shall
remain readily operable.

Caution
These service instructions are for use
by qualified service personnel only.
To reduce the risk of electric shock do not perform any
servicing other than that contained in the operation
instructions. Repairs have to be performed by qualified
service personnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.

LEGAL DISCLAIMER
TECHNICAL SPECIFICATIONS AND APPEARANCES
ARE SUBJECT TO CHANGE WITHOUT NOTICE AND
ACCURACY IS NOT GUARANTEED. BEHRINGER,
KLARK TEKNIK, MIDAS, BUGERA, AND TURBOSOUND
ARE PART OF THE MUSIC GROUP (MUSIC-GROUP.COM).
ALL TRADEMARKS ARE THE PROPERTY OF THEIR
RESPECTIVE OWNERS. MUSIC GROUP ACCEPTS NO
LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED
BY ANY PERSON WHO RELIES EITHER WHOLLY OR
IN PART UPON ANY DESCRIPTION, PHOTOGRAPH
OR STATEMENT CONTAINED HEREIN. COLORS AND
SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT.
MUSIC GROUP PRODUCTS ARE SOLD THROUGH
AUTHORIZED FULLFILLERS AND RESELLERS ONLY.
FULLFILLERS AND RESELLERS ARE NOT AGENTS OF
MUSIC GROUP AND HAVE ABSOLUTELY NO AUTHORITY

TO BIND MUSIC GROUP BY ANY EXPRESS OR IMPLIED
UNDERTAKING OR REPRESENTATION. THIS MANUAL
IS COPYRIGHTED. NO PART OF THIS MANUAL MAY
BE REPRODUCED OR TRANSMITTED IN ANY FORM
OR BY ANY MEANS, ELECTRONIC OR MECHANICAL,
INCLUDING PHOTOCOPYING AND RECORDING OF ANY
KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS
WRITTEN PERMISSION OF MUSIC GROUP IP LTD.
ALL RIGHTS RESERVED.
© 2013 MUSIC Group IP Ltd.
Trident Chambers, Wickhams Cay, P.O. Box 146,
Road Town, Tortola, British Virgin Islands

LIMITED WARRANTY
For the applicable warranty terms and conditions
and additional information regarding MUSIC Group’s
Limited Warranty, please see complete details online at
www.music-group.com/warranty.

XENYX X1222USB User Manual

1. Introduction
FBQ Feedback Detection System
The FBQ Feedback Detection System, integrated into the graphic equalizer, is one
of the most outstanding characteristics of this mixing console. This ingenious
circuitry lets you immediately recognize and eliminate feedback frequencies.
The FBQ Feedback Detection System uses the LEDs in the frequency band faders
of the graphic EQ to indicate the critical frequencies. This way, what once used to
be a labor-intensive search for feedback frequencies is now an activity that even
a child could master.
The microphone channels feature high-end XENYX Mic Preamps that compare
well with costly outboard preamps in terms of sound quality and dynamics and
boast the following features:
• 130 dB dynamic range for an incredible amount of headroom
• A bandwidth ranging from below 10 Hz to over 200 kHz for crystal-clear

reproduction of even the finest nuances

• The extremely low-noise and distortion-free circuitry guarantees absolutely

natural and transparent signal reproduction

• They are perfectly matched to every conceivable microphone with up to

60 dB gain and +48 volt phantom power supply

• They enable you to use the greatly extended dynamic range of your

24-bit/192 kHz HD recorder to the full, thereby maintaining optimal
audio quality

“British EQ”
The equalizers used for the XENYX Series are based on the legendary circuitry of
top-notch consoles made in Britain, which are renowned throughout the world
for their incredibly warm and musical sound character. Even with extreme gain
settings these equalizers ensure outstanding audio properties.
Multi-effects processor
Additionally, your XENYX mixing console has an effects processor with 24-bit
A/D and D/A converters included, which gives you 16 presets producing first-class
reverb, delay and modulation effects plus numerous multi-effects in excellent
audio quality.
The XENYX mixing consoles are equipped with a state-of-the-art switchedmode power supply (SMPS). Unlike conventional circuitry an SMPS provides
an optimum supply current regardless of the input voltage. And thanks to its
considerably higher efficiency a switched-mode power supply uses less energy
than conventional power supplies.

CAUTION!

We would like to draw your attention to the fact that extreme volumes may
damage your hearing and/or your headphones or loudspeakers. Turn the
MAIN MIX faders and the PHONES control in the main section fully down before
you switch on the unit. Always be careful to set the appropriate volume.

1.1 General mixing console functions
A mixing console fulfils three main functions:
• Signal processing:

Preamplification
Microphones convert sound waves into voltage that has to be amplified
several-fold; then, this voltage is turned into sound that is reproduced
in a loudspeaker. Because microphone capsules are very delicate in their
construction, output voltage is very low and therefore susceptible to
interference. Therefore, mic signal voltage is amplified directly at the mixer
input to a higher signal level that is less prone to interference. This higher,
interference-safe signal level has to be achieved through amplification
using an amplifier of the highest quality in order to amplify the signal and
add as little noise to it as possible. The XENYX Mic Preamp performs this
role beautifully, leaving no traces of noise or sound coloration. Interference
that could take place at the preamplification level could affect signal quality
and purity, and would then be passed on to all other devices, resulting in
inaccurate sounding program during recording or playback.
Level-setting
Signals fed into the mixer using a DI-box (Direct Injection) or the output of a
sound card or a keyboard, often have to be adjusted to the operating level of
your mixing console.
Frequency response correction
Using the equalizers found in each channel strip, you can simply, quickly and
effectively adjust the way a signal sounds.
Effects mixing
In addition to the effects processor contained in your mixer, using the
insert connectors on the mono channels and both aux busses lets you insert
additional signal processors into your signal path.
• Signal distribution:

Individual signals adjusted at each channel strip are laid out at the aux
sends and returns, and are either fed into external effects processors or fed
back to the internal effects processor. Then, the signals are brought back
into the main mix either via the aux return connectors or via direct internal
wiring. The mix for the on-stage musicians is also created using the aux
sends (monitor mix). Similarly, for example, signals for recording equipment,
power amplifiers, headphones and 2-track outputs can also be taken.
• Mix:

All other mixing console functions fall under this vital category. Creating a
mix means primarily adjusting the volume levels of individual instruments
and voices to one another as well as giving them the appropriate weight
within the overall frequency spectrum. Likewise, you’ll have to sensibly
spread individual voices across the stereo image of a signal. At the end of
this process, adjusting the level of the entire mix to other equipment in the
signal path is required (e.g. recorder/crossover/amplifier).
The interface of BEHRINGER mixing consoles is optimized for these tasks,
enabling you to easily keep track of the signal path.

XENYX X1222USB User Manual

1.2 The user’s manual

2. Control Elements and Connectors

The user’s manual is designed to give you both an overview of the controls, as
well as detailed information on how to use them. In order to help you understand
the links between the controls, we have arranged them in groups according to
their function.

This chapter describes the various control elements of your mixing console.
All controls, switches and connectors will be discussed in detail.

1.3 Before you get started

2.1.1 Microphone and line inputs

2.1 Mono channels

1.3.1 Shipment
Your mixing console was carefully packed in the factory to guarantee safe
transport. Nevertheless, we recommend that you carefully examine the
packaging and its contents for any signs of physical damage, which may have
occurred during transit.
◊ If the unit is damaged, please do NOT return it to us, but notify your

dealer and the shipping company immediately, otherwise claims for
damage or replacement may not be granted.
1.3.2 Initial operation
Be sure that there is enough space around the unit for cooling purposes and to
avoid over-heating. Please do not place your mixing console on high-temperature
devices such as radiators or power amps. The console is connected to the mains
via the supplied power cable. The console meets the required safety standards.
Blown fuses must only be replaced by fuses of the same type and rating.
◊ Please note that all units must be properly grounded. For your own

safety, you should never remove any ground connectors from electrical
devices or power cables, or render them inoperative.
◊ Please ensure that only qualified people install and operate the

mixing console. During installation and operation, the user must have
sufficient electrical contact to earth, otherwise electrostatic discharges
might affect the operation of the unit.
1.3.3 Online registration
Please do remember to register your new BEHRINGER equipment right after your
purchase by visiting behringer.com (alternatively behringer.de) and kindly read
the terms and conditions of our warranty carefully.
Should your BEHRINGER product malfunction, our goal is to have it repaired as
quickly as possible. To arrange for warranty service, please contact the retailer
from whom the equipment was purchased. Should your BEHRINGER dealer not
be located in your vicinity, you may directly contact one of our subsidiaries.
Corresponding contact information is included in the original equipment
packaging (Global Contact Information/European Contact Information).
Should your country not be listed, please contact the distributor nearest
you. A list of distributors can be found in the support area of our website
(behringer.com).
Registering your purchase and equipment with us helps us process your repair
claims quicker and more efficiently.
Thank you for your cooperation!

Fig. 2.1: Connectors and controls of mic/line inputs

MIC
Each mono input channel offers a balanced microphone input via the XLR
connector and also features switchable +48 V phantom power supply for
condenser microphones. The XENYX preamps provide undistorted and noise-free
gain as is typically known only from costly outboard preamps.
◊ Please mute your playback system before you activate the phantom

power supply to prevent switch-on thumps being directed to your
loudspeakers. Please also note the instructions in chapter 2.5
“Rear view of X1222USB”.
LINE IN
Each mono input also features a balanced line input on a ¼" connector.
Unbalanced devices (mono jacks) can also be connected to these inputs.
◊ Please remember that you can only use either the microphone

or the line input of a channel at any one time. You can never use
both simultaneously!
INSERT
Insert points enable the processing of a signal with dynamic processors or
equalizers. They are sourced pre-fader, pre-EQ and pre-aux send. Unlike reverb
or other effects devices, whose signals are usually added to the dry signal,
dynamic processors are most effective on the complete signal. In this case,
aux send paths are a less-than-perfect solution. It is better to interrupt the
signal path and insert a dynamic processor and/or equalizer. After processing,
the signal is routed back to the console at precisely the same point it left.
However, the channel signal path is interrupted only if a plug is inserted into the
corresponding jack (stereo phone plug: tip = signal output; ring = return input).
All mono input channels are equipped with inserts.
Inserts can also be used as pre-EQ direct outputs, without interrupting the signal
path. To this end, you will need a cable fitted with mono phone plugs on the tape
machine or effects device end, and a bridged stereo phone plug on the console
side (tip and ring connected).

XENYX X1222USB User Manual

LOW CUT

2.1.3 Aux sends (MON and FX)

The mono channels of the mixing consoles have a high-slope LOW CUT filter for
eliminating unwanted, low-frequency signal components (80 Hz, 18 dB/octave).
GAIN
Use the GAIN control to adjust the input gain. This control should always be
turned fully counter-clockwise whenever you connect or disconnect a signal
source to one of the inputs.
The scale has 2 different value ranges: the first value range (+10 to +60 dB)
refers to the MIC input and shows the amplification for the signals fed in there.
The second value range (+10 to -40 dB) refers to the line input and shows
its sensitivity. The settings for equipment with standard line-level signals
(-10 dBV or +4 dBu) look like this: While the GAIN control is turned all the way
down, connect your equipment. Set the GAIN control to the external devices’
standard output level. If that unit has an output signal level display, it should
show 0 dB during signal peaks. For +4 dBu, turn up GAIN slightly, for -10 dBV a
bit more. Tweaking is done using the LEVEL SET LED.

Fig. 2.3: The AUX SEND controls in the channel strips

Aux sends take signals via a control from one or more channels and sum these
signals to a so-called bus. This bus signal is sent to an aux send connector and
then routed, for example, to an active monitor speaker or an external effects
device. The return from an external effects device can then be brought back into
the console via the aux return connectors.
For situations that require effects processing, the aux sends are usually switched
post-fader so that the effects volume in a channel corresponds to the position
of the channel fader. If this were not the case, the effects signal of the channel
would remain audible even when the fader is turned to zero.

LEVEL SET

When setting up a monitor mix, the aux sends are generally switched to
pre-fader; i.e. they operate independently of the position of the channel fader.

This LED lights up when the optimum operating signal level is achieved.
During normal use, this LED should only light up during signal peaks.

Both aux sends are mono, are sourced after the equalizer and offer up to
+15 dB gain.

COMPRESSOR
Each mono channel features a built-in compressor which lowers the dynamic
range of the signal and increases its perceived loudness. The loud peaks are
squashed down and the quiet sections are boosted.
Turn the COMP knob clockwise to add more compression effect. The adjacent LED
with light when the effect is engaged.
2.1.2 Equalizer
All mono input channels include a 3-band equalizer. All bands provide boost or
cut of up to 15 dB. In the central position, the equalizer is inactive.
The circuitry of the British EQs is based on the technology used in the best-known
top-of-the-line consoles and providing a warm sound without any unwanted
side effects. The result are extremely musical equalizers which, unlike simple
equalizers, cause no side effects such as phase shifting or bandwidth limitation,
even with extreme gain settings of ±15 dB.

◊ If you press the MUTE switch of the respective channel, aux sends and

returns (MON and FX) are not being muted.
MON
In the X1222USB, aux send 1 (MON) is wired pre-fader and is thus particularly
suitable for setting up monitor mixes.
FX
The aux send labeled FX is for feeding external effects devices and is thus set up
to be post-fader.
In the X1222USB, the FX send is routed directly to the built-in effects processor.
To make sure that the effects processor receives an input signal, you shouldn’t
turn this control all the way to the left (-oo). Don’t have the FX MUTE switch
pressed, and you should also not have the FX SEND fader pulled down.
2.1.4 Pan, mute switch and channel fader

Fig. 2.2: The equalizer of the input channels

The upper (HIGH) and the lower band (LOW) are shelving filters that increase
or decrease all frequencies above or below their cut-off frequency. The cut-off
frequencies of the upper and lower band are 12 kHz and 80 Hz respectively.
The mid band is configured as a peak filter with a center frequency of 2.5 kHz.
Unlike shelving filters, the peak filter processes a frequency range that extends
upwards and downwards around its middle frequency.
Fig. 2.4: Channel fader and additional control elements

XENYX X1222USB User Manual

PAN
The PAN control determines the position of the channel signal within the stereo
image. This control features a constant-power characteristic, which means the
signal is always maintained at a constant level, irrespective of position in the
stereo panorama.
MUTE
Use the MUTE switch to mute the channel. This means that the channel signal
is no longer present in the main mix. However, the aux sends (MON and FX)
remain active.
MUTE LED
The MUTE LED indicates that the relevant channel is muted.
CLIP LED
The CLIP LED lights up when the input signal is driven too high. In this case,
lower apparent frequency increase on the channel EQ to avoid distortion.
For example, lower the mids and the highs somewhat to emphasize the bass.
If you don’t wish to change the EQ settings under any circumstances, try lowering
the GAIN control somewhat (counterclockwise).
If you inserted an external effects processor via the insert connector
(e.g. a dynamic processor), then you should also control its output signal level.
It should not be higher than its input signal level (0 dB).
The channel fader determines the level of the channel signal in the main mix.
◊ Attention: Since the aux path for the effect processor is connected

post-fader, the channel fader has to be turned up in order to get this
channel’s signal to the effects processor!

2.2 Stereo channels
2.2.1 Channel inputs

All stereo channel strips have a GAIN control for level setting. In those channels
in which a mic input is present in the channel, the GAIN control has two scales:
just like in the mono channels, there is a 0 to +40 dB scale that shows the
preamplification of the mic signal; the +20 to -20 dB scale shows the sensitivity
for the corresponding input level that is applied to the line input.
Both inputs can also be used with balanced or unbalanced connectors.
2.2.2 Equalizer stereo channels
The equalizer of the stereo channels is, of course, stereo. The filter characteristics
and crossover frequencies are the same as those of the mono channels. A stereo
equalizer is always preferable to two mono equalizers if frequency correction of a
stereo signal is needed. There is often a discrepancy between the settings of the
left and the right channels when using separate equalizers.
2.2.3 Aux sends stereo channels
In principle, the aux sends of the stereo channels function in just the same way as
those of the mono channels. As aux send paths are always mono, the signal on a
stereo channel is first summed to mono before it reaches the aux bus.
2.2.4 Balance, mute switch and channel fader
BAL
The function of the BAL(ANCE) control corresponds to the PAN control in the
mono channels.
The balance control determines the relative proportion between the left and
right input signals before both signals are routed to the main stereo mix bus.
The MUTE switch, MUTE LED, CLIP LED and channel fader function in the same
way as the mono channels.

2.3 Connector panel and main section
Whereas it was useful to trace the signal flow from top to bottom in order to gain
an understanding of the channel strips, we now look at the mixing console from
left to right. The signals are, so to speak, collected from one point on each of the
channel strips and then routed to the main section all together.
2.3.1 Monitor send and FX send channels

Fig. 2.5: Stereo channel inputs

Each stereo channel features two line-level inputs on ¼" connectors for left and
right channels. Channels 9/10 and 11/12 can also be used in mono if you only use
the connector labeled “L.”
Both channels 5/6 and 7/8 feature an additional balanced XLR input for
microphones with available +48 V phantom power.
Fig. 2.6: Aux send controls of the main section

A channel signal is routed to the MON(ITOR) send bus if the MON control is turned
up on the corresponding channel.

XENYX X1222USB User Manual

MON SEND
The aux send control MON SEND acts as master control for the monitor bus and
determines the level of the summed signal that is taken from the mixer via
the MON SEND connector and that can for example be fed to an amplifier for
monitor purposes.
Using the audio signal from this output, you can also feed a subwoofer if you
don’t require stage monitors. To this end, you should implement a crossover in
your signal path pre-subwoofer and pre-amplifier, so that only low frequencies
are fed into the subwoofer. You can achieve the same effect by using the built-in
graphical equalizer. Lower all frequencies above 160 Hz and assign the equalizer
to “Monitor”.

◊ If the connected effects processor receives no input signal, the FX MUTE

switch is probably pressed and/or the FX SEND control is too low.
This also goes for the built-in effects processor.
◊ Adjust your external effects processor to 100% wet (effects signal only),

because the effects signal is added to the main mix along with the
“dry” channel signals.
2.3.3 Aux return connectors

◊ When you use the MAIN MIX fader to reduce the overall volume,

keep in mind that the subwoofer is still receiving a signal!
FX TO MON
You can use this control to insert an effects signal from the built-in effects
processor to your monitor mix. Of course, to do this, your effects processor must
first receive a signal, i.e. the FX controls in the channel strips must be turned up,
and the FX SEND fader (see fig. 2.6) hast to be open.
MON MUTE
If the MON MUTE switch is pressed, the monitor bus is muted, i.e. there is no
signal at the MON SEND connector.
FX SEND
The FX SEND fader determines the overall level of the effects bus. Both external
effects processors (via the FX SEND connector) and the built-in processor only
receive an input signal if this control is open.
FX TO MAIN
Use the FX TO MAIN control to feed the effects signal into the main mix.
If the control is turned all the way to the left, no effects signal can be heard.
FX MUTE

Fig. 2.8: Aux return connectors

AUX RETURN 1
The AUX RETURN 1 connectors generally serve as the return path for the effects
mix generated using the FX send. This is where you connect the output signal
of the external effects device. If only the left connector is used, the aux return 1
automatically operates in mono.
◊ You can also use these connectors as additional line inputs.

AUX RETURN 2
The AUX RETURN 2 connectors are used exactly the same way as the AUX RETURN
1 connectors. If these connectors already function as additional inputs, you
can route the effects signal back into the console via a different stereo channel,
with the added benefit that the channel EQ can be used to adjust the frequency
response of the effects return signal.
◊ In this instance, the FX control of the channel being used as an effects

return should be turned fully counter-clockwise, otherwise feedback
problems can occur!
2.3.4 CD/tape return channel, voice canceller and
connection socket

If the FX MUTE switch is pressed, the effects channel is muted, i.e. no signal is
present at the FX SEND connector and the effects processor no longer receives an
input signal.
2.3.2 Monitor send and FX send connector

Fig. 2.7: Aux send connectors MON and FX

MON SEND
Connect the input of your monitor power amp or an active monitor system here
to make the monitor mix audible to the musicians on the stage. The signal mix is
created using the channels’ MON controls.
FX SEND
The FX SEND connector outputs the signal you picked up from the individual
channels using the FX controls. You can connect this to the input of an external
effects device in order to process the FX bus’ master signal. Once an effects mix is
created, the processed signal can then be routed from the effects device outputs
back into the AUX RETURN connectors.

Fig. 2.9: CD/tape return channel

This channel, intended especially for connecting stereo signal sources
(CD players, DAT recorders or even sound cards) features a particularly
practical feature: the VOICE CANCELLER.

XENYX X1222USB User Manual

VOICE CANCELLER

CD/TAPE OUTPUT

Here, you have a filter circuitry that lets you almost entirely remove the
vocal portion of a recording. The filter is constructed in such a way that voice
frequencies are targeted without majorly affecting the rest of the signal.
Additionally, the filter seizes only the middle of the stereo image, exactly there
where the vocals are typically located.

These connectors are wired pre graphic EQ and pre XPQ surround function.
They carry the main mix signal (unbalanced), effects mix included. Connect the
CD/TAPE OUTPUT to the inputs of your recording device. If you wish to use your
mixer solely for recording purposes, the main outputs are also an alternative.

Possible applications for the Voice Canceller are obvious: you can very simply
stage background music for Karaoke events. Of course, you can also do this at
home or at your rehearsal room before you hit the stage. Singers with their own
band can practice singing difficult parts using a complete playback from a tape
player or a CD, thus minimizing rehearsal time.

2.3.5 Main mix, main out connectors and
headphone connector

STANDBY
If the STANDBY switch is pressed, all input channels with a mic connector
(XLR connector) are muted. During breaks or stage conversion, you can prevent
noise from entering the sound system via the microphones. Such noise can in the
worst-case scenario even irreparably damage loudspeaker membranes. The cool
thing about this is that the main mix faders can remain open, so that you can play
music from a CD at the same time. Similarly, the faders for the muted channels
can also remain in their position.
To bring in other sound sources, you can use the CD/tape inputs, stereo input
channels 9 to 12 and the aux return inputs.
CD/TAPE MUTE
Using this switch, the input signal from the CD/tape inputs is muted.
CD/TAPE RET(URN)
This stereo fader assigns the input signal from the CD/tape inputs into the
main mix.

Fig. 2.11: Main mix fader

MAIN MIX
Use the high-precision quality faders to control the output level of the main mix.

Fig. 2.10: 2-track connectors

Fig. 2.12: Main out connectors

CD/TAPE INPUT

MAIN OUT

The CD/TAPE INPUT RCA connectors are provided for connecting a 2-track
machine (e.g. DAT recorder) or also a CD player. They can also be used as stereo
line input. Alternatively, the output signal of a second XENYX or BEHRINGER
ULTRALINK PRO MX882 can also be connected. If you connect a hi-fi amplifier
with a source selection switch to the CD/TAPE INPUT, you can easily switch
between additional sources (e.g. cassette recorder, MD player, sound card etc.).

The MAIN outputs carry the MAIN MIX signal and are on balanced XLR connectors
with a nominal level of +4 dBu. Depending on how you wish to use your mixer
and which gear you own, you can connect the following equipment:

Using the voice canceller function, you can process all signals being brought into
your mixing console via these connectors.

Live PA systems:
A stereo dynamics processor (optional), stereo equalizer (optional) and the stereo
power amplifier for full-range loud-speakers with passive crossovers.
If you wish to use multi-way loudspeaker systems without an integrated
crossover, you have to use an active crossover and several power amplifiers.
Often, limiters are already built into active crossovers (e.g. BEHRINGER SUPER-X
PRO CX2310 and ULTRADRIVE PRO DCX2496). Active crossovers are implemented
directly before the power amplifier, and they divide the frequency range into
several segments that are first amplified in the amplifiers and then passed onto
the corresponding loudspeakers.

XENYX X1222USB User Manual

Recording:
For mastering, using a stereo compressor such as the COMPOSER PRO-XL
MDX2600 can be recommended. Use it to custom-tailor the dynamic
characteristics of your signal to the dynamic range of the recording equipment
you are using. The signal is in this case passed on from the compressor into
the recorder.

◊ Connect microphones before you switch on the phantom power supply.

Please do not connect microphones to the mixer (or the stagebox/
wallbox) while the phantom power supply is switched on. In addition,
the monitor/PA loudspeakers should be muted before you activate the
phantom power supply. After switching on, wait approx. one minute to
allow for system stabilization.
LEVEL METER/CLIP

PHONES
The PHONES control adjusts the volume of the headphones connected to the
PHONS/CTRL connector. If you connect active monitors or an amplifier, use this
connector to adjust the output signal level.

CAUTION!

◊ We would like to draw your attention to the fact that extreme volumes

may damage your hearing and/or your headphones or loudspeakers.
Turn the MAIN MIX faders and the PHONES control in the main section
fully down before you switch on the unit. Always be careful to set the
appropriate volume.

The high-precision level meter accurately displays the appropriate signal level.
LEVEL SETTING:
When recording to a digital device, the recorder’s peak meter should not exceed
0 dB. This is because, unlike analog recordings, slightly excessive levels can create
unpleasant digital distortion.
When recording to an analog device, the VU meters of the recording machine
should reach approx. +3 dB with low-frequency signals (e.g. kick drum). Due to
their inertia VU meters tend to display too low a signal level at frequencies above
1 kHz. This is why, for example, a Hi-Hat should only be driven as far as -10 dB.
Snare drums should be driven to approx. 0 dB.
◊ The peak meters of your XENYX display the level virtually independent

of frequency. A recording level of 0 dB is recommended for all
signal types.
Fig. 2.13: PHONS/CTRL connector

2.3.7 USB input/output

PHONS/CTRL connector
You can connect headphones to this ¼" TRS connector. The connector can also
be used for feeding active monitor loudspeakers (or an amplifier) in your control
room. For this purpose, the signal is taken directly before it is passed on to the
main mix faders.
2.3.6 Level meter and level setting

Fig. 2.15: USB input/output

The XENYX mixer line has built-in USB connectivity, allowing stereo signals to
be sent to and from the mixer and a computer. The audio sent from the mixer to
a computer is identical to the MAIN MIX. Audio being sent to the mixer from a
computer can be routed to the main mix with the 2-TR/USB RTN fader.
Connect the USB type B plug into the USB jack on the mixer, and the other end
into a free USB port on your computer. There are no required drivers, but we
recommend that PC users install the included ASIO driver. The driver can also be
downloaded from behringer.com.

2.4 Graphic 7-band equalizer
Fig. 2.14: Level meter

POWER
The blue POWER LED indicates that the device is switched on.
+48 V
The red “+48 V” LED lights up when the phantom power supply is switched
on. The phantom power supply is necessary for condenser microphones and is
activated using the corresponding switch on the rear of the device.

Fig. 2.16: The graphic stereo equalizer

The graphic stereo equalizer allows you to tailor the sound to the room acoustics.

XENYX X1222USB User Manual

FBQ FEEDBACK DETECTION

PHANTOM

The switch turns on the FBQ Feedback Detection System. It uses the LEDs in the
frequency band faders to indicate the critical frequencies. On a per-need basis,
lower the frequency range in question somewhat in order to avoid feedback.
The graphic stereo equalizer has to be turned on in order to use this function.

The PHANTOM switch activates the phantom power supply for the XLR
microphone inputs, which is required to operate condenser microphones.
The red +48 V LED lights up when phantom power is on. As a rule,
dynamic microphones can still be used with phantom power switched on,
provided that they are wired in a balanced configuration. In case of doubt,
contact the microphone manufacturer!

◊ Logically, at least one (ideally several) microphone channels have to be

open for feedback to occur at all!
Feedback is particularly common when stage monitors (“wedges”) are
concerned, because monitors project sound in the direction of microphones.
Therefore, you can also use the FBQ Feedback Detection for monitors by placing
the equalizer in the monitor bus (see MAIN MIX/MONITOR).
EQ IN
Use this switch to activate the graphic equalizer. When activated, the fader LEDs
will illuminate.
MAIN MIX/MONITOR
This toggles the graphic equalizer between the main mix and the monitor mix.
With the switch up (not depressed), the equalizer is active in stereo on the main
mix, and inactive on the monitor mix.
When the switch is depressed the equalizer is active in mono on the monitor mix,
and inactive on the main mix.

2.5 Rear view of X1222USB

◊ Connect microphones before you switch on the phantom power supply.

connected) on the MIC input connectors if you want to use the phantom
power supply.
SERIAL NUMBER
Please note the important information on the serial number given in
chapter 1.3.3.

3. Digital Effects Processor and XPQ
Surround Function
3.1 Digital effects processor

Fig. 2.17: Voltage supply and fuse

FUSE HOLDER/IEC MAINS RECEPTACLE
The console is connected to the mains via the cable supplied, which meets the
required safety standards. Blown fuses must only be replaced by fuses of the
same type and rating. The mains connection is made via a cable with IEC mains
connector. An appropriate mains cable is supplied with the equipment.
POWER
Use the POWER switch to power up the mixing console. The POWER switch
should always be in the “Off” position when you are about to connect your unit
to the mains.
To disconnect the unit from the mains, pull out the main cord plug.
When installing the product, ensure that the plug is easily accessible. If mounting
in a rack, ensure that the mains can be easily disconnected by a plug pull or by an
all-pole disconnect switch on or near the rack.
◊ Attention: The POWER switch does not fully disconnect the unit from

Fig. 3.1: Effects presets overview

24-BIT MULTI-EFFECTS PROCESSOR
Here you can find a list of all presets stored in the multi-effects processor.
This built-in effects module produces high-grade standard effects such as
reverb, chorus, flanger, delay and various combination effects. The integrated
effects module has the advantage of requiring no wiring. This way, the danger
of creating ground loops or uneven signal levels is eliminated at the outset,
completely simplifying the handling.
These effect presets are designed to be added to dry signals. If you move the FX
TO MAIN control, you mix the channel signal (dry) and the effect signal.
This also goes for mixing effects signals with the monitor mix. The main
difference is that the mix ratio is adjusted using the FX TO MON control. Of course,
a signal has to be fed into the effects processor via the FX control in the channel
strip for both applications.

the mains. Unplug the power cord completely when the unit is not used
for prolonged periods of time.
Fig. 3.2: Connection socket for the footswitch

XENYX X1222USB User Manual

FOOTSWITCH
Connect a standard footswitch to the footswitch connector; use this to switch the
effects processor on and off. A flashing dot at the bottom of the display indicates
if the effects processor is muted via the footswitch.

¼" TS footswitch connector
strain relief clamp
sleeve
tip

◊ In chapter 4.2, you will find an illustration showing how to connect

your footswitch correctly.
sleeve
pole 1/ground

tip
pole 2

Fig. 3.3: Digital Effects module and XPQ Surround Function control elements

The footswitch connects both poles momentarily

LEVEL
The LED level meter on the effects module should display a sufficiently high
level. Take care to ensure that the clip LED only lights up at peak levels. If it is
lit constantly, you are overloading the effects processor and this could cause
unpleasant distortion. The FX SEND fader determines the level that reaches the
effects module.
PROGRAM
You can select the effect preset by turning the PROGRAM control. The display
flashes the number of the current preset. To recall the selected preset, press the
button; the flashing stops. You can also recall the selected preset using
the footswitch.

3.2 XPQ surround function
The surround function can be enabled/disabled with the XPQ TO MAIN switch.
This is a built-in effect that widens the stereo width, thus making the sound more
lively and transparent. Use the SURROUND control to determine the intensity of
this effect.

4. Installation

Fig. 4.1: ¼" TS footswitch connector

4.2.1 Audio connections
Please use commercial RCA cables to wire the 2-track inputs and outputs.
You can, of course, also connect unbalanced devices to the balanced input/
outputs. Use either mono plugs, or ensure that ring and sleeve are bridged inside
the stereo plug (or pins 1 & 3 in the case of XLR connectors).
◊ Caution! You must never use unbalanced XLR connectors (pins 1 and

3 connected) on the MIC inputs if you intend to use the phantom
power supply.
Balanced use with XLR connectors

2 1
3

input
1 = ground/shield
2 = hot (+ve)
3 = cold (-ve)
1

4.1 Rack mounting
The packaging of your mixing console contains two 19" rack mount brackets
which can be installed on the side panels of the console.
Before you can attach the rack mount brackets to the mixing console, you need
to remove the screws holding the left and right side panels. Use these screws to
fasten the two brackets onto the console, being careful to note that each bracket
fits a specific side. With the rack mount brackets installed, you can mount the
mixing console in a commercially available 19" rack. Be sure to allow for proper
air flow around the unit, and do not place the mixing console close to radiators or
power amps, so as to avoid overheating.

2
3

output
For unbalanced use, pin 1 and pin 3
have to be bridged

Fig. 4.2: XLR connections

Unbalanced ¼" TS connector
strain relief clamp
sleeve

◊ Only use the screws holding the mixing console side panels to fasten

tip

the 19" rack mounts.

4.2 Cable connections

sleeve
(ground/shield)

You will need a large number of cables for the various connections to and from
the console. The following illustrations show the wiring of these cables. Be sure
to use only high-grade cables.

tip
(signal)

Fig. 4.3: ¼" TS connector

XENYX X1222USB User Manual

Balanced ¼" TRS connector
strain relief clamp
sleeve
ring
tip

5. Specifications
Mono Inputs

Microphone Inputs (XENYX Mic Preamp)
Type

sleeve
ground/shield
ring
cold (-ve)
tip
hot (+ve)
For connection of balanced and unbalanced plugs,
ring and sleeve have to be bridged at the stereo plug.

Fig. 4.4: ¼" TRS connector

Insert send return ¼" TRS connector
strain relief clamp
sleeve
ring
tip

sleeve
ground/shield
ring
return (in)
tip
send (out)
Connect the insert send with the input and the
insert return with the output of the effects device.

Fig. 4.5: Insert send return ¼" TRS connector

¼" TRS headphones connector
strain relief clamp
sleeve
ring
tip

XLR, electronically balanced,
discrete input circuitry

Mic E.I.N. (20 Hz - 20 kHz)
@ 0 Ω source resistance

-134 dB / 135.7 dB A-weighted

@ 50 Ω source resistance

-131 dB / 133.5 dB A-weighted

@ 150 Ω source resistance

-129 dB / 130.5 dB A-weighted

Frequency response

<10 Hz - 150 kHz (-1 dB),
<10 Hz - 200 kHz (-3 dB)

Gain range

+10 to +60 dB

Max. input level

+12 dBu @ +10 dB Gain

Impedance

approx. 2.6 kΩ balanced

Signal-to-noise ratio

110 dB / 112 dB A-weighted
(0 dBu In @ +22 dB Gain)

Distortion (THD + N)

0.005% / 0.004% A-weighted

Line Input

Type

¼" TRS connector,
electronically balanced

Impedance

approx. 20 kΩ balanced
approx. 10 kΩ unbalanced

Gain range

-10 to +40 dB

Max. input level

+22 dBu @ 0 dB Gain

Fade-Out Attenuation (Crosstalk Attenuation)

Main fader closed

98 dB

Channel muted

85 dB

Channel fader muted

85 dB

Frequency Response
sleeve
ground/shield
ring
right signal
tip
left signal

Microphone input to main out
<10 Hz - 90 kHz

+0 dB / -1 dB

<10 Hz - 160 kHz

+0 dB / -3 dB

Stereo Inputs
Fig. 4.6: ¼" TRS connector for headphones

Channels 5/6, 7/8
Microphone input
Type

XLR microphone connector,
electronically balanced

Impedance

approx. 2.6 kΩ balanced

Gain range

0 dB to +40 dB

Max. input level

+2 dBu

XENYX X1222USB User Manual

Channels 9/10, 11/12

CD/Tape Out

Stereo line inputs

Type

RCA connectors

Type

2 x ¼" TRS connector, unbalanced

Impedance

approx. 1 kΩ

Impedance

approx. 40 kΩ @ 0 dB Gain

Max. output level

+22 dBu

Gain range

-20 dB to +20 dB

DSP

Texas Instruments

Max. input level

+22 dBu @ 0 dB Gain

Converter

24-bit Sigma-Delta
64/128-times oversampling

Sampling rate

40 kHz

CD/Tape In

Type

RCA connectors

Impedance

approx. 10 kΩ

Max. input level

+22 dBu

EQ Mono Channels
Low

80 Hz / ±15 dB

Mid

2.5 kHz / ±15 dB

High

12 kHz / ±15 dB

Low cut

80 Hz, 18 dB/oct.

EQ Stereo Channels
Low

80 Hz / ±15 dB

Mid

2.5 kHz / ±15 dB

High

12 kHz / ±15 dB

MON/FX Send
Type

¼" TS connector, unbalanced

Impedance

approx. 120 Ω

Max. output level

+22 dBu

Aux Returns

USB

Audio

Stereo In/Out

Connector

Type B

Converter 16-bit
Sample Rate

48 kHz

Main Mix System Data

Noise
Main mix @ -∞,
Channel fader -∞

-99 dB
-101 dB A-weighted

Main mix @ 0 dB,
Channel fader -∞

-84 dB
-87 dB A-weighted

Main mix @ 0 dB,
Channel fader @ 0 dB

-80 dB
-82 dB A-weighted

Power Supply

Mains Voltage

100 - 240 V~, 50 - 60 Hz

Power consumption

40 W

Type

¼" TRS connector, unbalanced

Fuse

T 1.6 A H 250 V

Impedance

approx. 10 kΩ

Mains connection

Standard IEC receptacle

Max. input level

+22 dBu

Main Outputs
Type

XLR, electronically balanced

Impedance

approx. 240 Ω balanced
approx. 120 Ω unbalanced

Max. output level

+28 dBu

Headphone Output
Type

¼" TRS connector, unbalanced

Max. output level

+19 dBu / 150 Ω (+25 dBm)

Physical

Dimensions (W x D x H)

approx. 14.56 x 13 x 3.54"
approx. 370 x 330 x 90 mm

Weight (net)

approx. 9.3 lbs.
approx. 4.22 kg

Measuring conditions:
1: 1 kHz rel. to 0 dBu; 20 Hz - 20 kHz; line input; main output; unity gain.
2: 20 Hz - 20kHz; measured at main output. Channels 1 - 4 unity gain; EQ flat; all channels on main mix;
channels 1/3 as far left as possible, channels 2/4 as far right as possible. Reference = +6 dBu.
BEHRINGER is constantly striving to manintain the highest professional standards. As a result of these efforts,
modifications may be made from time to time to existing products without prior notice. Specifications and
appearance may differ from those listed or illustrated.

XENYX X1222USB User Manual

FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION

XENYX X1222USB
Responsible Party Name:

MUSIC Group Services US Inc.

Address:

18912 North Creek Parkway,
Suite 200 Bothell, WA 98011,
USA

Phone/Fax No.:

Phone: +1 425 672 0816
Fax: +1 425 673 7647

XENYX X1222USB
complies with the FCC rules as mentioned in the following paragraph:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by MUSIC Group
can void the user’s authority to use the equipment.

We Hear You

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : BEHRINGER
Create Date                     : 2013:03:19 13:25:49+08:00
Modify Date                     : 2013:03:19 13:55:00+08:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-21:37:19
Instance ID                     : uuid:129e48b6-ff32-af45-9c55-2f4b6f37f43f
Original Document ID            : adobe:docid:indd:fc5c23c9-a85e-11df-9945-f5d144549ebf
Document ID                     : xmp.did:3B7A865F2E2068118083C8A600EB3883
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:A4051C2E292068118083C8A600EB3883
Derived From Document ID        : xmp.did:7BB3C6B5262068118083AD2775EE9283
Derived From Original Document ID: adobe:docid:indd:fc5c23c9-a85e-11df-9945-f5d144549ebf
Derived From Rendition Class    : default
History Action                  : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:4C4CB7A94620681188C6B55A9195E590, xmp.iid:4D4CB7A94620681188C6B55A9195E590, xmp.iid:45EF7402082068118083BC379147CE7A, xmp.iid:B4ECFF65192068118083A015CFDE6BC4, xmp.iid:2E3A96F24C2068118083A015CFDE6BC4, xmp.iid:C469A99F4A2068118EF19D55A2DABA9D, xmp.iid:B5F74FF02F20681180838EA8B7A438AD, xmp.iid:94B2D8693020681180838EA8B7A438AD, xmp.iid:42BDEF81142068118083F9617A357E73, xmp.iid:C5A16299142068118083F9617A357E73, xmp.iid:4EE39FDC192068118083B0A3E132DCEB, xmp.iid:6E3285E5242068118083B0A3E132DCEB, xmp.iid:EA463E31302068118083B0A3E132DCEB, xmp.iid:97A1FD38302068118083B0A3E132DCEB, xmp.iid:F04F4946302068118083B0A3E132DCEB, xmp.iid:F14F4946302068118083B0A3E132DCEB, xmp.iid:F24F4946302068118083B0A3E132DCEB, xmp.iid:F34F4946302068118083B0A3E132DCEB, xmp.iid:F44F4946302068118083B0A3E132DCEB, xmp.iid:1E84607C3C2068118083B0A3E132DCEB, xmp.iid:F93F0A833C2068118083B0A3E132DCEB, xmp.iid:1CEDA62F372068118083E0F1855C43CC, xmp.iid:1DEDA62F372068118083E0F1855C43CC, xmp.iid:1EEDA62F372068118083E0F1855C43CC, xmp.iid:07146742372068118083E0F1855C43CC, xmp.iid:93342074072068118083982844BF7CBF, xmp.iid:94342074072068118083982844BF7CBF, xmp.iid:62415DEC4320681188C6B1E58B9DFDAE, xmp.iid:63415DEC4320681188C6B1E58B9DFDAE, xmp.iid:95B7EC5D3F2068118083E9490FF27F21, xmp.iid:96B7EC5D3F2068118083E9490FF27F21, xmp.iid:7F39DF020C206811871F9FCF7AFDE4A7, xmp.iid:8039DF020C206811871F9FCF7AFDE4A7, xmp.iid:981FF3EC382068118083D942D75AB66C, xmp.iid:991FF3EC382068118083D942D75AB66C, xmp.iid:0F5ACB480D2068118083AF431BBF6871, xmp.iid:105ACB480D2068118083AF431BBF6871, xmp.iid:1BFCC38D36206811822ACAC747C06E67, xmp.iid:7C55E0CB4C206811822ACAC747C06E67, xmp.iid:3E6F11AF342068118A6DCAFC79515730, xmp.iid:23332074072068118083F47A8689D396, xmp.iid:3C4C4491082068118083F47A8689D396, xmp.iid:702EFB83092068118083F47A8689D396, xmp.iid:E105A1AA092068118083F47A8689D396, xmp.iid:EA38AB0E0B2068118083F47A8689D396, xmp.iid:FF2A94240B2068118083F47A8689D396, xmp.iid:8217C94D0C2068118083F47A8689D396, xmp.iid:8317C94D0C2068118083F47A8689D396, xmp.iid:FE01436A212068118083F47A8689D396, xmp.iid:01ABF0CD22206811822A8B56A3E29F90, xmp.iid:76E338A725206811822A8B56A3E29F90, xmp.iid:1DEE326026206811822A8B56A3E29F90, xmp.iid:808E39C026206811822A8B56A3E29F90, xmp.iid:ECAEFE9F2B206811822A8B56A3E29F90, xmp.iid:EDAEFE9F2B206811822A8B56A3E29F90, xmp.iid:A6FC4CFE2D206811822A8B56A3E29F90, xmp.iid:493C4DB33D206811822A8B56A3E29F90, xmp.iid:6CD41EE70A2068118083C8728054789B, xmp.iid:22054CA70B2068118083C8728054789B, xmp.iid:1975352F162068118083C8728054789B, xmp.iid:4E023C391F2068118083C8728054789B, xmp.iid:C23BCB98262068118083C8728054789B, xmp.iid:2B95B3F715206811822A87669875E609, xmp.iid:903DA72916206811822A87669875E609, xmp.iid:497713612D206811822A93005B27658E, xmp.iid:006182FE45206811822A93005B27658E, xmp.iid:1A28D85047206811822A93005B27658E, xmp.iid:E8FAF0F047206811822A93005B27658E, xmp.iid:A39F7ACD11206811822AD9307C4E8382, xmp.iid:22F4130212206811822AD9307C4E8382, xmp.iid:1492ACD5322068118083A68850F97CC1, xmp.iid:287A52892A20681197A5A23538542950, xmp.iid:1FD601D32B20681197A5A23538542950, xmp.iid:EC6EB45C2D20681197A5A23538542950, xmp.iid:82D745AB2D20681197A5A23538542950, xmp.iid:7220ADB02D20681197A5A23538542950, xmp.iid:7AD4519D232068118083AD2775EE9283, xmp.iid:A162D793262068118083AD2775EE9283, xmp.iid:7BB3C6B5262068118083AD2775EE9283, xmp.iid:1331BF0D0E2068118083E69DEB91844D, xmp.iid:252A0EB81A2068118083E69DEB91844D, xmp.iid:A52DA70309206811822ACC0668B184ED, xmp.iid:631EE7330B206811822ACC0668B184ED, xmp.iid:FF36CB3B09206811822AF4D8AF8479EB, xmp.iid:D828AF78152068118083DDA762C5CC2F, xmp.iid:7077F97A0F2068118083F8C7A85847FE, xmp.iid:71D4551929206811822AE92793DD0974, xmp.iid:654C58370A2068118083E56F4E757D67, xmp.iid:0651939516206811822AE7EF0CD90F21, xmp.iid:EA968C4E10206811822ABC305AB8698A, xmp.iid:A4051C2E292068118083C8A600EB3883, xmp.iid:3B7A865F2E2068118083C8A600EB3883, xmp.iid:9493F7B0072068118A6D915BD387317F, xmp.iid:568E187407206811808385AB28963F18, xmp.iid:68FCD8B707206811808385AB28963F18, xmp.iid:9E6ED00008206811808385AB28963F18, xmp.iid:9F6ED00008206811808385AB28963F18, xmp.iid:F7C6E64508206811808385AB28963F18, xmp.iid:9C45C31809206811808385AB28963F18, xmp.iid:4EA8BF2C09206811808385AB28963F18, xmp.iid:2CA3756D09206811808385AB28963F18, xmp.iid:7882808909206811808385AB28963F18, xmp.iid:B425C0C109206811808385AB28963F18, xmp.iid:606927CC09206811808385AB28963F18, xmp.iid:E5CBA9A80A206811808385AB28963F18, xmp.iid:CDD381C90A206811808385AB28963F18, xmp.iid:9183F05B0B206811808385AB28963F18, xmp.iid:0335008A0B206811808385AB28963F18, xmp.iid:8D7A30910B206811808385AB28963F18, xmp.iid:6A8F11230C206811808385AB28963F18, xmp.iid:0E08CE8C0C206811808385AB28963F18, xmp.iid:B4974EA10C206811808385AB28963F18, xmp.iid:0AD4639E0F206811808385AB28963F18, xmp.iid:A8BD2374072068118083B2B020547EE7, xmp.iid:EA80D893072068118083B2B020547EE7, xmp.iid:42C6F3C3072068118083B2B020547EE7, xmp.iid:43C6F3C3072068118083B2B020547EE7, xmp.iid:5D16C129082068118083B2B020547EE7, xmp.iid:BA774D35082068118083B2B020547EE7, xmp.iid:BB774D35082068118083B2B020547EE7, xmp.iid:2A5225B4282068118083C7B36BE4CBDB
History When                    : 2011:05:30 17:21:44+08:00, 2011:05:30 17:21:44+08:00, 2011:06:01 11:21:03+08:00, 2011:06:02 11:18:07+08:00, 2011:06:02 17:27:08+08:00, 2011:06:10 17:01:17+08:00, 2011:07:04 15:15:45+08:00, 2011:07:04 15:15:45+08:00, 2011:07:04 17:47:33+08:00, 2011:07:04 17:48:12+08:00, 2011:07:05 11:02:37+08:00, 2011:07:05 12:21:38+08:00, 2011:07:05 13:42:30+08:00, 2011:07:05 13:42:43+08:00, 2011:07:05 13:43:05+08:00, 2011:07:05 13:43:08+08:00, 2011:07:05 13:43:15+08:00, 2011:07:05 13:45:01+08:00, 2011:07:05 13:47:07+08:00, 2011:07:05 15:10:41+08:00, 2011:07:05 15:10:41+08:00, 2011:07:05 15:30:22+08:00, 2011:07:05 15:30:22+08:00, 2011:07:05 15:30:54+08:00, 2011:07:05 15:30:54+08:00, 2011:07:06 08:52:54+08:00, 2011:07:06 08:52:54+08:00, 2011:08:16 17:48:40+08:00, 2011:08:16 17:48:40+08:00, 2011:08:19 15:52:23+08:00, 2011:08:19 15:52:23+08:00, 2011:08:22 10:44:44+08:00, 2011:08:22 10:44:44+08:00, 2011:09:07 14:57:45+08:00, 2011:09:07 14:57:45+08:00, 2011:10:27 10:10:22+08:00, 2011:10:27 10:10:22+08:00, 2012:01:02 15:10:29+08:00, 2012:01:02 17:49:42+08:00, 2012:05:17 14:42:19+08:00, 2012:09:05 11:59:10+08:00, 2012:09:05 11:59:10+08:00, 2012:09:05 12:06+08:00, 2012:09:05 12:07:02+08:00, 2012:09:05 12:17+08:00, 2012:09:05 12:17:36+08:00, 2012:09:05 12:25:55+08:00, 2012:09:05 13:43:43+08:00, 2012:09:05 14:57:02+08:00, 2012:09:06 14:34:22+08:00, 2012:09:06 14:54:46+08:00, 2012:09:06 14:59:56+08:00, 2012:09:06 15:02:37+08:00, 2012:09:06 15:51:29+08:00, 2012:09:06 15:54:28+08:00, 2012:09:06 15:54:28+08:00, 2012:09:06 17:46:54+08:00, 2012:09:07 09:39:34+08:00, 2012:09:07 09:50:50+08:00, 2012:09:07 11:01:03+08:00, 2012:09:07 12:08:02+08:00, 2012:09:07 12:57:48+08:00, 2012:09:10 11:50:55+08:00, 2012:09:10 11:52:19+08:00, 2012:09:11 13:53:50+08:00, 2012:09:11 16:50:02+08:00, 2012:09:11 16:59:29+08:00, 2012:09:11 17:03:58+08:00, 2012:09:13 10:48:30+08:00, 2012:09:13 10:48:30+08:00, 2012:09:14 14:51:19+08:00, 2012:09:19 13:51:41+08:00, 2012:09:19 14:00:54+08:00, 2012:09:19 14:12:09+08:00, 2012:09:19 14:14:07+08:00, 2012:09:19 14:14:16+08:00, 2012:09:25 13:57:01+08:00, 2012:09:25 14:19:10+08:00, 2012:09:25 14:19:10+08:00, 2012:10:01 10:28:13+08:00, 2012:10:01 11:58:53+08:00, 2012:10:12 09:36:58+08:00, 2012:10:12 09:52:38+08:00, 2012:10:15 09:34:23+08:00, 2012:11:27 11:39:31+08:00, 2012:11:27 16:57:42+08:00, 2012:11:29 14:14:01+08:00, 2012:12:05 09:52:48+08:00, 2013:01:09 11:24:16+08:00, 2013:01:10 10:44:30+08:00, 2013:01:30 15:18:28+08:00, 2013:01:30 15:18:28+08:00, 2013:01:31 16:50:46+08:00, 2013:01:31 16:51:59+08:00, 2013:01:31 16:53:53+08:00, 2013:01:31 16:55:55+08:00, 2013:01:31 16:56:50+08:00, 2013:01:31 16:57:51+08:00, 2013:01:31 17:03:45+08:00, 2013:01:31 17:04:18+08:00, 2013:01:31 17:06:07+08:00, 2013:01:31 17:06:54+08:00, 2013:01:31 17:08:28+08:00, 2013:01:31 17:08:46+08:00, 2013:01:31 17:14:55+08:00, 2013:01:31 17:15:51+08:00, 2013:01:31 17:19:56+08:00, 2013:01:31 17:21:14+08:00, 2013:01:31 17:21:26+08:00, 2013:01:31 17:25:30+08:00, 2013:01:31 17:28:28+08:00, 2013:01:31 17:29:02+08:00, 2013:01:31 17:50:26+08:00, 2013:02:14 10:01:03+08:00, 2013:02:14 10:01:57+08:00, 2013:02:14 10:03:17+08:00, 2013:02:14 10:03:34+08:00, 2013:02:14 10:06:08+08:00, 2013:02:14 10:06:27+08:00, 2013:02:14 10:08:56+08:00, 2013:03:19 13:25:31+08:00
History Software Agent          : Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0
History Changed                 : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata
Metadata Date                   : 2013:03:19 13:55+08:00
Creator Tool                    : Adobe InDesign CS5 (7.0)
Page Image Page Number          : 1, 2
Page Image Format               : JPEG, JPEG
Page Image Width                : 256, 256
Page Image Height               : 256, 256
Page Image                      : (Binary data 8455 bytes, use -b option to extract), (Binary data 6301 bytes, use -b option to extract)
Doc Change Count                : 435
Format                          : application/pdf
Title                           : XENYX X1222USB
Creator                         : BEHRINGER
Producer                        : Adobe PDF Library 9.9
Trapped                         : False
Page Mode                       : UseOutlines
Page Count                      : 16

EXIF Metadata provided by EXIF.tools

Behringer Xenyx X1222Usb Users Manual

Behringer-Xenyx-X1222Usb-Owners-Manual behringer-xenyx-x1222usb-owners-manual

Navigation menu

Versions of this User Manual:

Views

Navigation