Behringer Xenyx X1222Usb Users Manual

Behringer-Xenyx-X1222Usb-Owners-Manual behringer-xenyx-x1222usb-owners-manual

: Behringer Behringer-Xenyx-X1222Usb-Users-Manual-752300 behringer-xenyx-x1222usb-users-manual-752300 behringer pdf

Open the PDF directly: View PDF .
Page Count: 16

User Manual

X1222

Premium 16-Input 2/2-Bus Mixer with XENYX Mic Preamps

& Compressors, British EQs, 24-Bit Multi-FX Processor and

USB/Audio Interface

2XENYX X1222USB User Manual

Thank you

Congratulations! In purchasing the BEHRINGER XENYX you have acquired a

mixer whose small size belies its incredible versatility and audio performance.

The XENYX Series represents a milestone in the development of mixing console

technology. With the new XENYX microphone preamps including phantom power

as an option, balanced line inputs and a powerful eects section, themixing

consoles in the XENYX Series are optimally equipped for live and studio

applications. Owing to state-of-the-art circuitry, your XENYX console produces

a warm analog sound that is unrivalled. With the addition of the latest digital

technology, these best-in-class consoles combine the advantages of both analog

and digital technology.

Table of Contents

Thank you .......................................................................2

Important Safety Instructions ...................................... 3

Legal Disclaimer ............................................................. 3

Limited warranty ............................................................ 3

1. Introduction ............................................................... 4

1.1 General mixing console functions ............................... 4

1.2 The user’s manual ............................................................... 5

1.3 Before you get started ...................................................... 5

2. Control Elements and Connectors .......................... 5

2.1 Mono channels .................................................................... 5

2.2 Stereo channels ................................................................... 7

2.3 Connector panel and main section ............................. 7

2.4 Graphic 7-band equalizer .............................................. 10

2.5 Rear view of X1222USB ................................................... 11

3. Digital Eects Processor and

XPQ Surround Function ............................................... 11

3.1 Digital eects processor ................................................. 11

3.2 XPQ surround function .................................................. 12

4. Installation ............................................................... 12

4.1 Rack mounting ................................................................... 12

4.2 Cable connections ........................................................... 12

5. Specications ........................................................... 13

3XENYX X1222USB User Manual

Important Safety

Instructions

LEGAL DISCLAIMER

LIMITED WARRANTY

Terminals marked with this symbol carry

electrical current of su cient magnitude

to constitute risk of electric shock.

Use only high-quality professional speaker cables with

¼" TS or twist-locking plugs pre-installed. Allother

installation or modi cation should be performed only

by quali edpersonnel.

This symbol, wherever it appears,

alertsyou to the presence of uninsulated

dangerous voltage inside the

enclosure-voltage that may be su cient to constitute a

risk ofshock.

This symbol, wherever it appears,

alertsyou to important operating and

maintenance instructions in the

accompanying literature. Please read the manual.

Caution

To reduce the risk of electric shock, donot

remove the top cover (or the rear section).

No user serviceable parts inside. Refer servicing to

quali ed personnel.

Caution

To reduce the risk of  re or electric shock,

do not expose this appliance to rain and

moisture. The apparatus shall not be exposed to dripping

or splashing liquids and no objects  lled with liquids,

suchas vases, shall be placed on the apparatus.

Caution

These service instructions are for use

by quali ed service personnel only.

Toreduce the risk of electric shock do not perform any

servicing other than that contained in the operation

instructions. Repairs have to be performed by quali ed

servicepersonnel.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including ampli ers) that produce heat.

9. Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding-type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. Ifthe

provided plug does not  t into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Use only attachments/accessories speci ed by

themanufacturer.

12. Use only with the

cart, stand, tripod, bracket,

or table speci ed by the

manufacturer, orsold with

the apparatus. When a cart

is used, use caution when

moving the cart/apparatus

combination to avoid

injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to quali ed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power supply cord or plug

is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed

to rain or moisture, does not operate normally, or has

beendropped.

15. The apparatus shall be connected to a MAINS socket

outlet with a protective earthing connection.

16. Where the MAINS plug or an appliance coupler is

used as the disconnect device, the disconnect device shall

remain readily operable.

TECHNICAL SPECIFICATIONS AND APPEARANCES

ARE SUBJECT TO CHANGE WITHOUT NOTICE AND

ACCURACY IS NOT GUARANTEED. BEHRINGER,

KLARKTEKNIK, MIDAS, BUGERA, AND TURBOSOUND

ARE PART OF THE MUSIC GROUP MUSICGROUP.COM.

ALL TRADEMARKS ARE THE PROPERTY OF THEIR

RESPECTIVE OWNERS. MUSICGROUP ACCEPTS NO

LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED

BY ANY PERSON WHO RELIES EITHER WHOLLY OR

IN PART UPON ANY DESCRIPTION, PHOTOGRAPH

OR STATEMENT CONTAINED HEREIN. COLORS AND

SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT.

MUSIC GROUP PRODUCTS ARE SOLD THROUGH

AUTHORIZED FULLFILLERS AND RESELLERS ONLY.

FULLFILLERSAND RESELLERS ARE NOT AGENTS OF

MUSICGROUP AND HAVE ABSOLUTELY NO AUTHORITY

TO BIND MUSICGROUP BY ANY EXPRESS OR IMPLIED

UNDERTAKING OR REPRESENTATION. THIS MANUAL

IS COPYRIGHTED. NO PART OF THIS MANUAL MAY

BE REPRODUCED OR TRANSMITTED IN ANY FORM

OR BY ANY MEANS, ELECTRONIC OR MECHANICAL,

INCLUDING PHOTOCOPYING AND RECORDING OF ANY

KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS

WRITTEN PERMISSION OF MUSICGROUPIPLTD.

ALL RIGHTS RESERVED.

© 2013 MUSICGroupIPLtd.

Trident Chambers, Wickhams Cay, P.O. Box 146,

Road Town, Tortola, British Virgin Islands

For the applicable warranty terms and conditions

and additional information regarding MUSIC Group’s

Limited Warranty, please see complete details online at

www.music-group.com/warranty.

4XENYX X1222USB User Manual

1. Introduction

FBQ Feedback Detection System

The FBQ Feedback Detection System, integrated into the graphic equalizer, is one

of the most outstanding characteristics of this mixing console. This ingenious

circuitry lets you immediately recognize and eliminate feedback frequencies.

TheFBQ Feedback Detection System uses the LEDs in the frequency band faders

of the graphic EQ to indicate the critical frequencies. This way, what once used to

be a labor-intensive search for feedback frequencies is now an activity that even

a child could master.

The microphone channels feature high-end XENYX Mic Preamps that compare

well with costly outboard preamps in terms of sound quality and dynamics and

boast the following features:

• 130 dB dynamic range for an incredible amount of headroom

• A bandwidth ranging from below 10 Hz to over 200 kHz for crystal-clear

reproduction of even the nest nuances

• The extremely low-noise and distortion-free circuitry guarantees absolutely

natural and transparent signal reproduction

• They are perfectly matched to every conceivable microphone with up to

60dB gain and +48 volt phantom power supply

• They enable you to use the greatly extended dynamic range of your

24-bit/192 kHz HD recorder to the full, thereby maintaining optimal

audioquality

“British EQ”

The equalizers used for the XENYX Series are based on the legendary circuitry of

top-notch consoles made in Britain, which are renowned throughout the world

for their incredibly warm and musical sound character. Even with extreme gain

settings these equalizers ensure outstanding audio properties.

Multi-eects processor

Additionally, your XENYX mixing console has an eects processor with 24-bit

A/Dand D/A converters included, which gives you 16 presets producing rst-class

reverb, delay and modulation eects plus numerous multi-eects in excellent

audio quality.

The XENYX mixing consoles are equipped with a state-of-the-art switched-

mode power supply (SMPS). Unlike conventional circuitry an SMPS provides

an optimum supply current regardless of the input voltage. And thanks to its

considerably higher eciency a switched-mode power supply uses less energy

than conventional power supplies.

 CAUTION!

We would like to draw your attention to the fact that extreme volumes may

damage your hearing and/or your headphones or loudspeakers. Turn the

MAINMIX faders and the PHONES control in the main section fully down before

you switch on the unit. Always be careful to set the appropriate volume.

1.1 General mixing console functions

A mixing console fulls three main functions:

• Signal processing:

Preamplication

Microphones convert sound waves into voltage that has to be amplied

several-fold; then, this voltage is turned into sound that is reproduced

in a loudspeaker. Because micro phone capsules are very delicate in their

construction, output voltage is very low and therefore susceptible to

interference. Therefore, mic signal voltage is amplied directly at the mixer

input to a higher signal level that is less prone to interference. This higher,

interference-safe signal level has to be achieved through amplication

using an amplier of the highest quality in order to amplify the signal and

add as little noise to it as possible. The XENYX Mic Preamp performs this

role beautifully, leaving no traces of noise or sound coloration. Interference

that could take place at the preamplication level could aect signal quality

and purity, and would then be passed on to all other devices, resulting in

inaccurate sounding program during recording or playback.

Level-setting

Signals fed into the mixer using a DI-box (Direct Injection) or the output of a

sound card or a keyboard, often have to be adjusted to the operating level of

your mixing console.

Frequency response correction

Using the equalizers found in each channel strip, you can simply, quickly and

eectively adjust the way a signal sounds.

Eects mixing

In addition to the eects processor contained in your mixer, using the

insert connectors on the mono channels and both aux busses lets you insert

additional signal processors into your signal path.

• Signal distribution:

Individual signals adjusted at each channel strip are laid out at the aux

sends and returns, and are either fed into external eects processors or fed

back to the internal eects processor. Then, the signals are brought back

into the main mix either via the aux return connectors or via direct internal

wiring. The mix for the on-stage musicians is also created using the aux

sends (monitor mix). Similarly,for example, signals for recording equipment,

power ampli ers, headphones and 2-track outputs can also be taken.

• Mix:

All other mixing console functions fall under this vital category. Creating a

mix means primarily adjusting the volume levels of individual instruments

and voices to one another as well as giving them the appropriate weight

within the overall frequency spectrum. Likewise, you’ll have to sensibly

spread individual voices across the stereo image of a signal. At the end of

this process, adjusting the level of the entire mix to other equipment in the

signal path is required (e.g. recorder/crossover/amplier).

The interface of BEHRINGER mixing consoles is optimized for these tasks,

enabling you to easily keep track of the signal path.

5XENYX X1222USB User Manual

1.2 The user’s manual

The user’s manual is designed to give you both an overview of the controls, as

well as detailed information on how to use them. In order to help you understand

the links between the controls, we have arranged them in groups according to

their function.

1.3 Before you get started

1.3.1 Shipment

Your mixing console was carefully packed in the factory to guarantee safe

transport. Nevertheless, we recommend that you carefully examine the

packaging and its contents for any signs of physical damage, which may have

occurred during transit.

◊ If the unit is damaged, please do NOT return it to us, but notify your

dealer and the shipping company immediately, otherwise claims for

damage or replacement may not be granted.

1.3.2 Initial operation

Be sure that there is enough space around the unit for cooling purposes and to

avoid over-heating. Please do not place your mixing console on high-temperature

devices such as radiators or power amps. The console is connected to the mains

via the supplied power cable. The console meets the required safety standards.

Blown fuses must only be replaced by fuses of the same type and rating.

◊ Please note that all units must be properly grounded. For your own

safety, you should never remove any ground connectors from electrical

devices or power cables, or render them in operative.

◊ Please ensure that only qualified people install and operate the

mixing console. During installation and operation, the user must have

sufficient electrical contact to earth, otherwise electrostatic discharges

might affect the operation of the unit.

1.3.3 Online registration

Please do remember to register your new BEHRINGER equipment right after your

purchase by visiting behringer.com (alternatively behringer.de) and kindly read

the terms and conditions of our warranty carefully.

Should your BEHRINGER product malfunction, our goal is to have it repaired as

quickly as possible. To arrange for warranty service, please contact the retailer

from whom the equipment was purchased. Should your BEHRINGER dealer not

be located in your vicinity, you may directly contact one of our subsidiaries.

Corresponding contact information is included in the original equipment

packaging (Global Contact Information/European Contact Information).

Shouldyour country not be listed, please contact the distributor nearest

you. Alist of distributors can be found in the support area of our website

(behringer.com).

Registering your purchase and equipment with us helps us process your repair

claims quicker and more eciently.

Thank you for your cooperation!

2. Control Elements and Connectors

This chapter describes the various control elements of your mixing console.

Allcontrols, switches and connectors will be discussed in detail.

2.1 Mono channels

2.1.1 Microphone and line inputs

Fig. 2.1: Connectors and controls of mic/line inputs

MIC

Each mono input channel oers a balanced microphone input via the XLR

connector and also features switchable +48 V phantom power supply for

condenser microphones. The XENYX preamps provide undistorted and noise-free

gain as is typically known only from costly outboard preamps.

◊ Please mute your playback system before you activate the phantom

power supply to prevent switch-on thumps being directed to your

loud speakers. Please also note the instructions in chapter 2.5

“Rear view of X1222USB”.

LINE IN

Each mono input also features a balanced line input on a ¼" connector.

Unbalanced devices (mono jacks) can also be connected to these inputs.

◊ Please remember that you can only use either the microphone

or the line input of a channel at any one time. You can never use

both simultaneously!

INSERT

Insert points enable the processing of a signal with dynamic processors or

equalizers. They are sourced pre-fader, pre-EQ and pre-aux send. Unlike reverb

or other eects devices, whose signals are usually added to the dry signal,

dynamicprocessors are most eective on the complete signal. In this case,

auxsend paths are a less-than-perfect solution. It is better to interrupt the

signal path and insert a dynamic processor and/or equalizer. After processing,

the signal is routed back to the console at precisely the same point it left.

However, thechannel signal path is interrupted only if a plug is inserted into the

corresponding jack (stereophone plug: tip = signal output; ring = return input).

All mono input channels are equipped with inserts.

Inserts can also be used as pre-EQ direct outputs, without interrupting the signal

path. To this end, you will need a cable tted with mono phone plugs on the tape

machine or eects device end, and a bridged stereo phone plug on the console

side (tip and ring connected).

6XENYX X1222USB User Manual

LOW CUT

The mono channels of the mixing consoles have a high-slope LOW CUT lter for

eliminating unwanted, low-frequency signal components (80 Hz, 18 dB/octave).

GAIN

Use the GAIN control to adjust the input gain. This control should always be

turned fully counter-clockwise whenever you connect or disconnect a signal

source to one of the inputs.

The scale has 2 dierent value ranges: the rst value range (+10 to +60 dB)

refers to the MIC input and shows the amplication for the signals fed in there.

The second value range (+10 to -40 dB) refers to the line input and shows

its sensitivity. The settings for equipment with standard line-level signals

(-10 dBV or +4 dBu) look like this: While the GAIN control is turned all the way

down, connect your equipment. Set the GAIN control to the external devices’

standard output level. If that unit has an output signal level display, it should

show 0 dB during signal peaks. For +4dBu, turn up GAIN slightly, for -10 dBV a

bit more. Tweaking is done using the LEVEL SET LED.

LEVEL SET

This LED lights up when the optimum operating signal level is achieved.

Duringnormal use, this LED should only light up during signal peaks.

COMPRESSOR

Each mono channel features a built-in compressor which lowers the dynamic

range of the signal and increases its perceived loudness. The loud peaks are

squashed down and the quiet sections are boosted.

Turn the COMP knob clockwise to add more compression eect. The adjacent LED

with light when the eect is engaged.

2.1.2 Equalizer

All mono input channels include a 3-band equalizer. All bands provide boost or

cut of up to 15 dB. In the central position, the equalizer is inactive.

The circuitry of the British EQs is based on the technology used in the best-known

top-of-the-line consoles and providing a warm sound without any unwanted

side eects. The result are extremely musical equalizers which, unlike simple

equalizers, cause no side eects such as phase shifting or bandwidth limitation,

even with extreme gain settings of ±15 dB.

Fig. 2.2: The equalizer of the input channels

The upper (HIGH) and the lower band (LOW) are shelving lters that increase

or decrease all frequencies above or below their cut-o frequency. The cut-o

frequencies of the upper and lower band are 12 kHz and 80Hz respectively.

Themid band is congured as a peak lter with a center frequency of 2.5 kHz.

Unlike shelving lters, the peak lter processes a frequency range that extends

upwards and downwards around its middle frequency.

2.1.3 Aux sends (MON and FX)

Fig. 2.3: The AUX SEND controls in the channel strips

Aux sends take signals via a control from one or more channels and sum these

signals to a so-called bus. This bus signal is sent to an aux send connector and

then routed, for example, to an active monitor speaker or an external eects

device. The return from an external eects device can then be brought back into

the console via the aux return connectors.

For situations that require eects processing, the aux sends are usually switched

post-fader so that the eects volume in a channel corresponds to the position

of the channel fader. If this were not the case, the eects signal of the channel

would remain audible even when the fader is turned to zero.

When setting up a monitor mix, the aux sends are generally switched to

pre-fader; i.e. they operate independently of the position of the channel fader.

Both aux sends are mono, are sourced after the equalizer and oer up to

+15 dB gain.

◊ If you press the MUTE switch of the respective channel, aux sends and

returns (MON and FX) are not being muted.

MON

In the X1222USB, aux send 1 (MON) is wired pre-fader and is thus particularly

suitable for setting up monitor mixes.

FX

The aux send labeled FX is for feeding external eects devices and is thus set up

to be post-fader.

In the X1222USB, the FX send is routed directly to the built-in eects processor.

Tomake sure that the eects processor receives an input signal, you shouldn’t

turn this control all the way to the left (-oo). Don’t have the FX MUTE switch

pressed, and you should also not have the FX SEND fader pulled down.

2.1.4 Pan, mute switch and channel fader

Fig. 2.4: Channel fader and additional control elements

7XENYX X1222USB User Manual

PAN

The PAN control determines the position of the channel signal within the stereo

image. This control features a constant-power characteristic, which means the

signal is always maintained at a constant level, irrespective of position in the

stereo panorama.

MUTE

Use the MUTE switch to mute the channel. This means that the channel signal

is no longer present in the main mix. However, the aux sends (MON and FX)

remainactive.

MUTE LED

The MUTE LED indicates that the relevant channel is muted.

CLIP LED

The CLIP LED lights up when the input signal is driven too high. In this case,

lowerapparent frequency increase on the channel EQ to avoid distortion.

Forexample, lower the mids and the highs somewhat to emphasize the bass.

Ifyou don’t wish to change the EQ settings under any circumstances, try lowering

the GAIN control somewhat (counterclockwise).

If you inserted an external eects processor via the insert connector

(e.g. a dynamic processor), then you should also control its output signal level.

Itshould not be higher than its input signal level (0 dB).

The channel fader determines the level of the channel signal in the main mix.

◊ Attention: Since the aux path for the effect processor is connected

post-fader, the channel fader has to be turned up in order to get this

channel’s signal to the effects processor!

2.2 Stereo channels

2.2.1 Channel inputs

Fig. 2.5: Stereo channel inputs

Each stereo channel features two line-level inputs on ¼" connectors for left and

right channels. Channels 9/10 and 11/12 can also be used in mono if you only use

the connector labeled “L.”

Both channels 5/6 and 7/8 feature an additional balanced XLR input for

microphones with available +48 V phantom power.

All stereo channel strips have a GAIN control for level setting. In those channels

in which a mic input is present in the channel, the GAIN control has two scales:

just like in the mono channels, there is a 0 to +40 dB scale that shows the

preamplication of the mic signal; the +20 to -20 dB scale shows the sensitivity

for the corresponding input level that is applied to the line input.

Both inputs can also be used with balanced or unbalanced connectors.

2.2.2 Equalizer stereo channels

The equalizer of the stereo channels is, of course, stereo. The lter characteristics

and crossover frequencies are the same as those of the mono channels. A stereo

equalizer is always preferable to two mono equalizers if frequency correction of a

stereo signal is needed. There is often a discrepancy between the settings of the

left and the right channels when using separate equalizers.

2.2.3 Aux sends stereo channels

In principle, the aux sends of the stereo channels function in just the same way as

those of the mono channels. As aux send paths are always mono, the signal on a

stereo channel is rst summed to mono before it reaches the aux bus.

2.2.4 Balance, mute switch and channel fader

BAL

The function of the BAL(ANCE) control corresponds to the PAN control in the

mono channels.

The balance control determines the relative proportion between the left and

right input signals before both signals are routed to the main stereo mix bus.

The MUTE switch, MUTE LED, CLIP LED and channel fader function in the same

way as the mono channels.

2.3 Connector panel and main section

Whereas it was useful to trace the signal ow from top to bottom in order to gain

an understanding of the channel strips, we now look at the mixing console from

left to right. The signals are, so to speak, collected from one point on each of the

channel strips and then routed to the main section all together.

2.3.1 Monitor send and FX send channels

Fig. 2.6: Aux send controls of the main section

A channel signal is routed to the MON(ITOR) send bus if the MON control is turned

up on the corresponding channel.

8XENYX X1222USB User Manual

MON SEND

The aux send control MON SEND acts as master control for the monitor bus and

determines the level of the summed signal that is taken from the mixer via

the MON SEND connector and that can for example be fed to an amplier for

monitorpurposes.

Using the audio signal from this output, you can also feed a subwoofer if you

don’t require stage monitors. To this end, you should implement a crossover in

your signal path pre-subwoofer and pre-amplier, so that only low frequencies

are fed into the subwoofer. You can achieve the same eect by using the built-in

graphical equalizer. Lower all frequencies above 160 Hz and assign the equalizer

to “Monitor”.

◊ When you use the MAIN MIX fader to reduce the overall volume,

keep in mind that the subwoofer is still receiving a signal!

FX TO MON

You can use this control to insert an eects signal from the built-in eects

processor to your monitor mix. Of course, to do this, your eects processor must

rst receive a signal, i.e. the FX controls in the channel strips must be turned up,

and the FX SEND fader (see g. 2.6) hast to be open.

MON MUTE

If the MON MUTE switch is pressed, the monitor bus is muted, i.e. there is no

signal at the MON SEND connector.

FX SEND

The FX SEND fader determines the overall level of the eects bus. Both external

eects processors (via the FX SEND connector) and the built-in processor only

receive an input signal if this control is open.

FX TO MAIN

Use the FX TO MAIN control to feed the eects signal into the main mix.

If the control is turned all the way to the left, no eects signal can be heard.

FX MUTE

If the FX MUTE switch is pressed, the eects channel is muted, i.e. no signal is

present at the FX SEND connector and the eects processor no longer receives an

input signal.

2.3.2 Monitor send and FX send connector

Fig. 2.7: Aux send connectors MON and FX

MON SEND

Connect the input of your monitor power amp or an active monitor system here

to make the monitor mix audible to the musicians on the stage. The signal mix is

created using the channels’ MON controls.

FX SEND

The FX SEND connector outputs the signal you picked up from the individual

channels using the FX controls. You can connect this to the input of an external

eects device in order to process the FX bus’ master signal. Once an eects mix is

created, the processed signal can then be routed from the eects device outputs

back into the AUX RETURN connectors.

◊ If the connected effects processor receives no input signal, the FX MUTE

switch is probably pressed and/or the FX SEND control is too low.

This also goes for the built-in effects processor.

◊ Adjust your external effects processor to 100% wet (effects signal only),

because the effects signal is added to the main mix along with the

“dry” channel signals.

2.3.3 Aux return connectors

Fig. 2.8: Aux return connectors

AUX RETURN 1

The AUX RETURN 1 connectors generally serve as the return path for the eects

mix generated using the FX send. This is where you connect the output signal

of the external eects device. If only the left connector is used, the aux return 1

automatically operates in mono.

◊ You can also use these connectors as additional line inputs.

AUX RETURN 2

The AUX RETURN 2 connectors are used exactly the same way as the AUX RETURN

1 connectors. If these connectors already function as additional inputs, you

can route the eects signal back into the console via a dierent stereo channel,

with the added benet that the channel EQ can be used to adjust the frequency

response of the eects return signal.

◊ In this instance, the FX control of the channel being used as an effects

return should be turned fully counter-clockwise, otherwise feedback

problems can occur!

2.3.4 CD/tape return channel, voice canceller and

connection socket

Fig. 2.9: CD/tape return channel

This channel, intended especially for connecting stereo signal sources

(CD players, DAT recorders or even sound cards) features a particularly

practicalfeature: the VOICE CANCELLER.

9XENYX X1222USB User Manual

VOICE CANCELLER

Here, you have a lter circuitry that lets you almost entirely remove the

vocal portion of a recording. The lter is constructed in such a way that voice

frequencies are targeted without majorly aecting the rest of the signal.

Additionally, the lter seizes only the middle of the stereo image, exactly there

where the vocals are typically located.

Possible applications for the Voice Canceller are obvious: you can very simply

stage background music for Karaoke events. Of course, you can also do this at

home or at your rehearsal room before you hit the stage. Singers with their own

band can practice singing dicult parts using a complete playback from a tape

player or a CD, thus minimizing rehearsal time.

STANDBY

If the STANDBY switch is pressed, all input channels with a mic connector

(XLRconnector) are muted. During breaks or stage conversion, you can prevent

noise from entering the sound system via the microphones. Such noise can in the

worst-case scenario even irreparably damage loudspeaker membranes. The cool

thing about this is that the main mix faders can remain open, so that you can play

music from a CD at the same time. Similarly, the faders for the muted channels

can also remain in their position.

To bring in other sound sources, you can use the CD/tape inputs, stereo input

channels 9 to 12 and the aux return inputs.

CD/TAPE MUTE

Using this switch, the input signal from the CD/tape inputs is muted.

CD/TAPE RET(URN)

This stereo fader assigns the input signal from the CD/tape inputs into the

mainmix.

Fig. 2.10: 2-track connectors

CD/TAPE INPUT

The CD/TAPE INPUT RCA connectors are provided for connecting a 2-track

machine (e.g. DAT recorder) or also a CD player. They can also be used as stereo

line input. Alternatively, the output signal of a second XENYX or BEHRINGER

ULTRALINK PRO MX882 can also be connected. If you connect a hi- amplier

with a source selection switch to the CD/TAPE INPUT, you can easily switch

between additional sources (e.g. cassette recorder, MDplayer, sound card etc.).

Using the voice canceller function, you can process all signals being brought into

your mixing console via these connectors.

CD/TAPE OUTPUT

These connectors are wired pre graphic EQ and pre XPQ surround function.

Theycarry the main mix signal (unbalanced), eects mix included. Connect the

CD/TAPE OUTPUT to the inputs of your recording device. If you wish to use your

mixer solely for recording purposes, the main outputs are also an alternative.

2.3.5 Main mix, main out connectors and

headphoneconnector

Fig. 2.11: Main mix fader

MAIN MIX

Use the high-precision quality faders to control the output level of the main mix.

Fig. 2.12: Main out connectors

MAIN OUT

The MAIN outputs carry the MAIN MIX signal and are on balanced XLR connectors

with a nominal level of +4 dBu. Depending on how you wish to use your mixer

and which gear you own, you can connect the following equipment:

Live PA systems:

A stereo dynamics processor (optional), stereo equalizer (optional) and the stereo

power amplier for full-range loud-speakers with passive crossovers.

If you wish to use multi-way loudspeaker systems without an integrated

crossover, you have to use an active crossover and several power ampliers.

Often, limiters are already built into active crossovers (e.g. BEHRINGER SUPER-X

PRO CX2310 and ULTRADRIVE PRO DCX2496). Active crossovers are implemented

directly before the power amplier, and they divide the frequency range into

several segments that are rst amplied in the ampliers and then passed onto

the corresponding loudspeakers.

10 XENYX X1222USB User Manual

Recording:

For mastering, using a stereo compressor such as the COMPOSER PRO-XL

MDX2600 can be recommended. Use it to custom-tailor the dynamic

characteristics of your signal to the dynamic range of the recording equipment

you are using. The signal is in this case passed on from the compressor into

therecorder.

PHONES

The PHONES control adjusts the volume of the headphones connected to the

PHONS/CTRL connector. If you connect active monitors or an amplier, use this

connector to adjust the output signal level.

 CAUTION!

◊ We would like to draw your attention to the fact that extreme volumes

may damage your hearing and/or your headphones or loudspeakers.

Turn the MAIN MIX faders and the PHONES control in the main section

fully down before you switch on the unit. Always be careful to set the

appropriate volume.

Fig. 2.13: PHONS/CTRL connector

PHONS/CTRL connector

You can connect headphones to this ¼" TRS connector. The connector can also

be used for feeding active monitor loudspeakers (or an amplier) in your control

room. For this purpose, the signal is taken directly before it is passed on to the

main mix faders.

2.3.6 Level meter and level setting

Fig. 2.14: Level meter

POWER

The blue POWER LED indicates that the device is switched on.

+48 V

The red “+48 V” LED lights up when the phantom power supply is switched

on. The phantom power supply is necessary for condenser microphones and is

activated using the corresponding switch on the rear of the device.

◊ Connect microphones before you switch on the phantom power supply.

Please do not connect microphones to the mixer (or the stagebox/

wallbox) while the phantom power supply is switched on. In addition,

the monitor/PA loudspeakers should be muted before you activate the

phantom power supply. After switching on, wait approx. one minute to

allow for system stabilization.

LEVEL METER/CLIP

The high-precision level meter accurately displays the appropriate signal level.

LEVEL SETTING:

When recording to a digital device, the recorder’s peak meter should not exceed

0 dB. This is because, unlike analog recordings, slightly excessive levels can create

unpleasant digital distortion.

When recording to an analog device, the VU meters of the recording machine

should reach approx. +3 dB with low-frequency signals (e.g. kick drum). Due to

their inertia VU meters tend to display too low a signal level at frequencies above

1 kHz. This is why, for example, a Hi-Hat should only be driven as far as -10dB.

Snaredrums should be driven to approx. 0 dB.

◊ The peak meters of your XENYX display the level virtually independent

of frequency. A recording level of 0 dB is recommended for all

signal types.

2.3.7 USB input/output

Fig. 2.15: USB input/output

The XENYX mixer line has built-in USB connectivity, allowing stereo signals to

be sent to and from the mixer and a computer. The audio sent from the mixer to

a computer is identical to the MAIN MIX. Audio being sent to the mixer from a

computer can be routed to the main mix with the 2-TR/USB RTN fader.

Connect the USB type B plug into the USB jack on the mixer, and the other end

into a free USB port on your computer. There are no required drivers, but we

recommend that PC users install the included ASIO driver. The driver can also be

downloaded from behringer.com.

2.4 Graphic 7-band equalizer

Fig. 2.16: The graphic stereo equalizer

The graphic stereo equalizer allows you to tailor the sound to the room acoustics.

11 XENYX X1222USB User Manual

FBQ FEEDBACK DETECTION

The switch turns on the FBQ Feedback Detection System. It uses the LEDs in the

frequency band faders to indicate the critical frequencies. On a per-need basis,

lower the frequency range in question somewhat in order to avoid feedback.

Thegraphic stereo equalizer has to be turned on in order to use this function.

◊ Logically, at least one (ideally several) microphone channels have to be

open for feedback to occur at all!

Feedback is particularly common when stage monitors (“wedges”) are

concerned, because monitors project sound in the direction of microphones.

Therefore, you can also use the FBQ Feedback Detection for monitors by placing

the equalizer in the monitor bus (see MAIN MIX/MONITOR).

EQ IN

Use this switch to activate the graphic equalizer. When activated, the fader LEDs

will illuminate.

MAIN MIX/MONITOR

This toggles the graphic equalizer between the main mix and the monitor mix.

With the switch up (not depressed), the equalizer is active in stereo on the main

mix, and inactive on the monitor mix.

When the switch is depressed the equalizer is active in mono on the monitor mix,

and inactive on the main mix.

2.5 Rear view of X1222USB

Fig. 2.17: Voltage supply and fuse

FUSE HOLDER/IEC MAINS RECEPTACLE

The console is connected to the mains via the cable supplied, which meets the

required safety standards. Blown fuses must only be replaced by fuses of the

same type and rating. The mains connection is made via a cable with IEC mains

connector. An appropriate mains cable is supplied with the equipment.

POWER

Use the POWER switch to power up the mixing console. The POWER switch

should always be in the “O” position when you are about to connect your unit

to themains.

To disconnect the unit from the mains, pull out the main cord plug.

Wheninstalling the product, ensure that the plug is easily accessible. If mounting

in a rack, ensure that the mains can be easily disconnected by a plug pull or by an

all-pole disconnect switch on or near the rack.

◊ Attention: The POWER switch does not fully disconnect the unit from

the mains. Unplug the power cord completely when the unit is not used

for prolonged periods of time.

PHANTOM

The PHANTOM switch activates the phantom power supply for the XLR

microphone inputs, which is required to operate condenser microphones.

The red +48 V LED lights up when phantom power is on. As a rule,

dynamicmicrophones can still be used with phantom power switched on,

provided that they are wired in a balanced conguration. In case of doubt,

contact the microphone manufacturer!

◊ Connect microphones before you switch on the phantom power supply.

Please do not connect microphones to the mixer (or the stagebox/

wallbox) while the phantom power supply is switched on. In addition,

the monitor/PA loudspeakers should be muted before you activate the

phantom power supply. After switching on, wait approx. one minute to

allow for system stabilization.

◊ Caution! You must never use unbalanced XLR connectors (PIN 1 and 3

connected) on the MIC input connectors if you want to use the phantom

power supply.

SERIAL NUMBER

Please note the important information on the serial number given in

chapter1.3.3.

3. Digital Eects Processor and XPQ

Surround Function

3.1 Digital eects processor

Fig. 3.1: Eects presets overview

24-BIT MULTI-EFFECTS PROCESSOR

Here you can nd a list of all presets stored in the multi-eects processor.

This built-in eects module produces high-grade standard eects such as

reverb, chorus, anger, delay and various combination eects. The integrated

eects module has the advantage of requiring no wiring. This way, the danger

of creating ground loops or uneven signal levels is eliminated at the outset,

completely simplifying the handling.

These eect presets are designed to be added to dry signals. If you move the FX

TO MAIN control, you mix the channel signal (dry) and the eect signal.

This also goes for mixing eects signals with the monitor mix. The main

dierence is that the mix ratio is adjusted using the FX TO MON control. Of course,

a signal has to be fed into the eects processor via the FX control in the channel

strip for both applications.

Fig. 3.2: Connection socket for the footswitch

12 XENYX X1222USB User Manual

FOOTSWITCH

Connect a standard footswitch to the footswitch connector; use this to switch the

eects processor on and o. A ashing dot at the bottom of the display indicates

if the eects processor is muted via the footswitch.

◊ In chapter 4.2, you will find an illustration showing how to connect

your footswitch correctly.

Fig. 3.3: Digital Eects module and XPQ Surround Function control elements

LEVEL

The LED level meter on the eects module should display a suciently high

level. Take care to ensure that the clip LED only lights up at peak levels. If it is

lit constantly, you are overloading the eects processor and this could cause

unpleasant distortion. The FX SEND fader determines the level that reaches the

eects module.

PROGRAM

You can select the eect preset by turning the PROGRAM control. The display

ashes the number of the current preset. To recall the selected preset, pressthe

button; the ashing stops. You can also recall the selected preset using

thefootswitch.

3.2 XPQ surround function

The surround function can be enabled/disabled with the XPQTOMAIN switch.

This is a built-in eect that widens the stereo width, thus making the sound more

lively and transparent. Use the SURROUND control to determine the intensity of

this eect.

4. Installation

4.1 Rack mounting

The packaging of your mixing console contains two 19" rack mount brackets

which can be installed on the side panels of the console.

Before you can attach the rack mount brackets to the mixing console, you need

to remove the screws holding the left and right side panels. Use these screws to

fasten the two brackets onto the console, being careful to note that each bracket

ts a specic side. With the rack mount brackets installed, you can mount the

mixing console in a commercially available 19" rack. Be sure to allow for proper

air ow around the unit, and do not place the mixing console close to radiators or

power amps, so as to avoid overheating.

◊ Only use the screws holding the mixing console side panels to fasten

the 19" rack mounts.

4.2 Cable connections

You will need a large number of cables for the various connections to and from

the console. The following illustrations show the wiring of these cables. Be sure

to use only high-grade cables.

strain relief clamp

sleeve

tip

sleeve

pole 1/ground

tip

pole 2

The footswitch connects both poles momentarily

¼" TS footswitch connector

Fig. 4.1: ¼" TS footswitch connector

4.2.1 Audio connections

Please use commercial RCA cables to wire the 2-track inputs and outputs.

You can, of course, also connect unbalanced devices to the balanced input/

outputs. Use either mono plugs, or ensure that ring and sleeve are bridged inside

the stereo plug (or pins 1 & 3 in the case of XLR connectors).

◊ Caution! You must never use unbalanced XLR connectors (pins 1 and

3 connected) on the MIC inputs if you intend to use the phantom

power supply.

output

For unbalanced use, pin 1 and pin 3

have to be bridged

1 = ground/shield

2 = hot (+ve)

3 = cold (-ve)

input

12

3

12

3

Balanced use with XLR connectors

Fig. 4.2: XLR connections

strain relief clamp

sleeve

tip

sleeve

(ground/shield)

Unbalanced ¼" TS connector

tip

(signal)

Fig. 4.3: ¼" TS connector

13 XENYX X1222USB User Manual

strain relief clamp

sleeve

ring

tip

sleeve

ground/shield

For connection of balanced and unbalanced plugs,

ring and sleeve have to be bridged at the stereo plug.

Balanced ¼" TRS connector

ring

cold (-ve)

tip

hot (+ve)

Fig. 4.4: ¼" TRS connector

strain relief clamp

sleeve

ring

tip

sleeve

ground/shield

Connect the insert send with the input and the

insert return with the output of the eects device.

Insert send return ¼" TRS connector

ring

return (in)

tip

send (out)

Fig. 4.5: Insert send return ¼" TRS connector

strain relief clamp

sleeve

ring

tip

sleeve

ground/shield

¼" TRS headphones connector

ring

right signal

tip

left signal

Fig. 4.6: ¼" TRS connector for headphones

5. Specications

Mono Inputs

Microphone Inputs (XENYX Mic Preamp)

Type XLR, electronically balanced,

discrete input circuitry

Mic E.I.N. (20 Hz - 20 kHz)

@ 0 Ω source resistance -134 dB / 135.7 dB A-weighted

@ 50 Ω source resistance -131 dB / 133.5 dB A-weighted

@ 150 Ω source resistance -129 dB / 130.5 dB A-weighted

Frequency response <10 Hz - 150 kHz (-1 dB),

<10 Hz - 200 kHz (-3 dB)

Gain range +10 to +60 dB

Max. input level +12 dBu @ +10 dB Gain

Impedance approx. 2.6 kΩ balanced

Signal-to-noise ratio 110 dB / 112 dB A-weighted

(0 dBu In @ +22 dB Gain)

Distortion (THD + N) 0.005% / 0.004% A-weighted

Line Input

Type ¼" TRS connector,

electronicallybalanced

Impedance approx. 20 kΩ balanced

approx. 10 kΩ unbalanced

Gain range -10 to +40 dB

Max. input level +22 dBu @ 0 dB Gain

Fade-Out Attenuation (Crosstalk Attenuation)

Main fader closed 98 dB

Channel muted 85 dB

Channel fader muted 85 dB

Frequency Response

Microphone input to main out

<10 Hz - 90 kHz +0 dB / -1 dB

<10 Hz - 160 kHz +0 dB / -3 dB

Stereo Inputs

Channels 5/6, 7/8

Microphone input

Type XLR microphone connector,

electronically balanced

Impedance approx. 2.6 kΩ balanced

Gain range 0 dB to +40 dB

Max. input level +2 dBu

14 XENYX X1222USB User Manual

Channels 9/10, 11/12

Stereo line inputs

Type 2 x ¼" TRS connector, unbalanced

Impedance approx. 40 kΩ @ 0 dB Gain

Gain range -20 dB to +20 dB

Max. input level +22 dBu @ 0 dB Gain

CD/Tape In

Type RCA connectors

Impedance approx. 10 kΩ

Max. input level +22 dBu

EQ Mono Channels

Low 80 Hz / ±15 dB

Mid 2.5 kHz / ±15 dB

High 12 kHz / ±15 dB

Low cut 80 Hz, 18 dB/oct.

EQ Stereo Channels

Low 80 Hz / ±15 dB

Mid 2.5 kHz / ±15 dB

High 12 kHz / ±15 dB

MON/FX Send

Type ¼" TS connector, unbalanced

Impedance approx. 120 Ω

Max. output level +22 dBu

Aux Returns

Type ¼" TRS connector, unbalanced

Impedance approx. 10 kΩ

Max. input level +22 dBu

Main Outputs

Type XLR, electronically balanced

Impedance approx. 240 Ω balanced

approx. 120 Ω unbalanced

Max. output level +28 dBu

Headphone Output

Type ¼" TRS connector, unbalanced

Max. output level +19 dBu / 150 Ω (+25 dBm)

CD/Tape Out

Type RCA connectors

Impedance approx. 1 kΩ

Max. output level +22 dBu

DSP Texas Instruments

Converter 24-bit Sigma-Delta

64/128-times oversampling

Sampling rate 40 kHz

USB

Audio Stereo In/Out

Connector Type B

Converter 16-bit

Sample Rate 48 kHz

Main Mix System Data

Noise

Main mix @ -∞, -99 dB

Channel fader -∞ -101 dB A-weighted

Main mix @ 0 dB, -84 dB

Channel fader -∞ -87 dB A-weighted

Main mix @ 0 dB, -80 dB

Channel fader @ 0 dB -82 dB A-weighted

Power Supply

Mains Voltage 100 - 240 V~, 50 - 60 Hz

Power consumption 40 W

Fuse T 1.6 A H 250 V

Mains connection Standard IEC receptacle

Physical

Dimensions (W x D x H) approx. 14.56 x 13 x 3.54"

approx. 370 x 330 x 90 mm

Weight (net) approx. 9.3 lbs.

approx. 4.22 kg

Measuring conditions:

1: 1 kHz rel. to 0 dBu; 20 Hz - 20 kHz; line input; main output; unity gain.

2: 20 Hz - 20kHz; measured at main output. Channels 1 - 4 unity gain; EQ flat; all channels on main mix;

channels 1/3 as far left as possible, channels 2/4 as far right as possible. Reference = +6 dBu.

BEHRINGER is constantly striving to manintain the highest professional standards. As a result of these efforts,

modifications may be made from time to time to existing products without prior notice. Specifications and

appearance may differ from those listed or illustrated.

15 XENYX X1222USB User Manual

FEDERAL COMMUNICATIONS

COMMISSION COMPLIANCE

INFORMATION

Responsible Party Name: MUSIC Group Services US Inc.

Address: 18912 North Creek Parkway,

Suite 200 Bothell, WA 98011,

USA

Phone/Fax No.: Phone: +1 425 672 0816

Fax: +1 425 673 7647

XENYX X1222USB

complies with the FCC rules as mentioned in the followingparagraph:

This equipment has been tested and found to comply with the limits for a ClassB

digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment o and on, the user is encouraged to try to correct the

interference by one or more of the followingmeasures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician forhelp.

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

Important information:

Changes or modications to the equipment not expressly approved by MUSIC Group

can void the user’s authority to use the equipment.

XENYX X1222USB

We Hear You