Blizzard Ski Automobile Accessories 810Ss Users Manual #1 2003

2015-02-02

: Blizzard-Ski Blizzard-Ski-Blizzard-Ski-Automobile-Accessories-810Ss-Users-Manual-420485 blizzard-ski-blizzard-ski-automobile-accessories-810ss-users-manual-420485 blizzard-ski pdf

Open the PDF directly: View PDF PDF.
Page Count: 36

2003 Assembly & Operation Manual
Blizzard®Power Plow®Snowplow
Model 810SS
BLIZZARD
POWER PLOW
®
YEARS
1999
2003
to
www.blizzardplows.com
iTable of Contents
Table of Contents
01 Snowplow Accessories
02 Warning!
03 Snowplow Operation
Assembly Instructions
04 Unpacking & Inspection
05 Moldboard Assembly
06 A-frame Assembly
07 Electrical Assembly - Control Wire Harness
08 Testing The Snowplow
09 Mounting & Dismounting Instructions
Maintenance & Plow Specifications
10 Regular Maintenance
11 Storing Your Snowplow
12 Plow Specifications
Torque Specifications
13 Bolts & Hydraulic Adapters
Plow Diagrams & Part Lists
14 Model 810SS Power Plow Snowplow Parts List
16 Model 810SS Power Plow Snowplow Assembly Schematic
18 Hydraulic Manifold Detail
Electrical Diagrams
19 Coil Harness & Hydraulic Manifold Schematic
20 Pistol Grip Control Wire Harness Diagram
21 Pistol Grip Control Wire Schematic
22 Wire Harness Extension (Vehicle Side) Diagram
23 Wire Harness Extension (Vehicle Side) Wire Schematic
24 Wire Harness Extension (Plow Side) Diagram
25 Wire Harness Extension (Plow Side) Wire Schematic
26 Coil Wire Harness Diagram
27 Coil Wire Harness Wire Schematic
28 Auxiliary Control Harness Diagram
29 Auxiliary Control Harness Wire Schematic
Troubleshooting
30 Troubleshooting Guide
Warranties
32 Limited Consumer Warranty
33 Commercial Warranty
Introduction
Congratulations on purchasing the most
advanced all-season skid steer snowplow
attachment available! The Blizzard Power
Plow Model 810SS is clearing new trails
for innovative design, rugged durability,
quality craftsmanship and superior per-
formance. Our exclusive products are
manufactured and tested in Michigan’s
Upper Peninsula, the snow capital of the
Midwest. With an annual snowfall averaging
over 250," we couldn’t imagine building
snow removal products anywhere else!
Your Blizzard Power Plow is equipped
with versatile features designed for
years of dependable service.Twelve-
inch expanding wings automatically
transform a compact 8' blade into a
massive 10' machine. Also, the inde-
pendent wings can pivot forward to form
our 9'-3" BucketBlade™ position. Now
you can carry more snow even further.
Turn your Power Plow into an all-season
skid steer blade with an easy to install
optional trip-lock assembly. This one
piece accessory replaces the standard
trip springs to provide a rigid grading
blade. Safety features include full mold-
board trip action, enclosed hydraulics
and automatic cylinder pressure relief.
To ensure years of optimum snowplow
performance, review the contents of this
manual. It contains assembly information,
detailed diagrams, complete parts listings,
maintenance guidelines and trouble-
shooting tips.
Should you need additional information,
contact your local Blizzard Power Plow
Dealer. Their knowledgeable staff is
well informed on the latest Power Plow
information. They are also your source
for replacement parts, technical assis-
tance and all service repairs.
Comments, suggestions or concerns?
Address all correspondence to:
Blizzard Corporation
Customer Service Department
95 Airpark Boulevard
Calumet, MI 49913
Snowplow Accessories 01
Heavy-Duty 3/8" Wing Cutting
Edges with Hardware
P/N 61288
Beef-up your Blizzard Power Plow
snowplow with our 3/8" thick wing
cutting edges. Made of T1 material,
these edges are built to withstand
heavy plow use on the roughest
road surfaces. These durable wing edges also provide added
material for protection against sidewalk curb wear. Mounting
hardware included.
810SS Trip-Lock Assembly
with Hardware
P/N 70028
Turn your Blizzard Power Plow
into an all-season skid steer blade
with an easy to install trip-lock
assembly. This one-piece acces-
sory replaces the standard trip
springs to provide a rigid grading blade. Now you can level and
grade material in a fraction of the time! Trip-Lock assembly shipped
complete with mounting hardware.
Auxiliary Control Harness
P/N 62162
Integrate all snowplow controls into
your skid steer using an optional
auxiliary control harness. This 7 ft.
braided harness connects easily
to your existing manifold harness
on one end and your skid steer on
the other. Assembly of the harness wiring to your skid steer-spe-
cific auxiliary electrical controls required. Electrical connector not
provided with harness. Some connectors available for purchase.
Snowplow Accessories
All of the accessories pictured below are currently offered for your snow-
plow. See your local authorized Blizzard Dealer for pricing and availability.
Visit our web site at www.blizzardplows.com to view new snowplow
accessories and our latest Blizzard snowplow wearables.
Rubber Snow Deflector
P/N 61241
Plow safer and easier with our
custom rubber snow deflector.
This easy-to-install accessory
keeps snow off of your windshield
and in its place— on the ground!
Rugged and durable, the 3/8"
thick, 2-ply construction is made to last. The one piece rubber
design allows for wing clearance and provides optimum snow
deflection. The deflector is shipped with a “Blizzard Power Plow”
vinyl decal and complete mounting hardware.
Blizzard Snowplow
Touch-Up Paint
P/N 61219 (Gloss White)
P/N 63073 (Gloss Black)
Putting your snowplow away for
the winter? Have a deep scratch
to cover? Clean up your blade and
plow parts with our gloss spray
paints. Blizzard snowplow touch-
up paint provides an excellent finish to help keep your snowplow
looking its best. Paint provided in 12 oz. spray cans.
02 Warning!
Warning!
Prior to operating your Power Plow snowplow, review the WARNING!
label at the passenger’s side rear of the moldboard (shown below).
Note: Read and understand all warnings indicated in this manual prior
to operating the snowplow. Warnings and cautions in the manual are
indicated by the icons shown to the left.
WARNING:
CAUTION:
Should the WARNING! label or any of the labels
that came with your snowplow become hard to
read or wear off, contact your local authorized
Blizzard dealer for replacements.
Calumet, MI 49913
1. Properly mount the snowplow attachment prior to moving the skid steer.
2. Always inform persons to stand clear of the snowplow and skid steer attachment
plates when mounting. Failure to do so may result in serious injury or death.
3. Securely position all mounting levers prior to operating your skid steer attachment.
4. Never use the snowplow attachment to carry people, as a man lift or work platform.
5. Always travel with the wings fully retracted.
6. Do not change the position of the blade while in transit.
7. Always lower the attachment when the skid steer is parked.
8. Never stand, work or reach under lift arms or lift cylinders without an approved lift
arm stop installed. Failure to do so may result in serious injury or death.
9. Use caution when plowing with down pressure. The plow attachment can cause the
front wheels on the skid steer to raise.
10. High pressure hydraulic fluid can puncture skin causing serious injury or death.
In the event of a hydraulic leak, lower load or relieve hydraulic pressure before
loosening hydraulic fittings.
If injured, seek emergency medical help immediately.
Blizzard Power Plow snowplow is protected by U.S. Patents 5,899,007 and 5,638,618. Other patents pending.
READ
OWNER’S
MANUAL
THOROUGHLY
PRIOR TO
OPERATING
PLOW.
WARNING
WARNING
BLZ 1013
D.
C.
B.
A.
Snowplow Operation 03
Snowplow Operation
Your Blizzard Power Plow snowplow is the most advanced and versatile
snowplow on the market. The easy to use controls allow you to automat-
ically adjust the plow blade and wings into an infinite number of plowing
positions. Review the illustrations below to determine the best position for
your plowing needs.
A. Compact Position (8' Blade Width)
•Primary position when transporting
the snowplow
•For use in heavy snow conditions with poor
visibility, initial clearing and tight quarters
•Ideal application: Residential driveways,
small roads
B. WidePass™ Position (10' Blade Width)
•Primary position for clearing large surfaces
•For use in light snow conditions with good
visibility, final clearing and clean-up
•Ideal application: Large parking lots,
widening roadways
C. BucketBlade™ Position (9'-3" Blade Width)
•Primary position for transporting snow
•For use in initial clearing with decent visibility,
transporting large volumes of snow, final
clean-up
•Ideal application: Roadway intersections
D. WidePass™ Position Angled with
Wing Forward
•Primary position for accelerated angled plowing
•For use in directional plowing, cornering,
diverting snow away from objects or buildings
•Ideal application: Plowing adjacent to buildings,
driveway /road intersections
04 Unpacking & Inspection
Assembly Instructions
Unpacking & Inspection
Your Blizzard Power Plow snowplow has been packaged to withstand
transit and weather related damage. Fully inspect all components upon
receipt of your plow. In the event of shipping damage or missing parts,
immediately contact our Customer Service Department at 1-888-680-8600.
Begin unpacking and inspection in the following order:
1. Remove the shipping document from the end panel of the pallet wrap.
Retain all documentation for your records.
2. All wood framing and polyethylene material should be removed from
the pallet for easy access to the snowplow.
3. Due to the odd shaped components and size of several assembly
parts, various cable ties and corrugated material are used for scratch
resistance and package orientation. Please remove these items prior
to assembly.
4. Place the main blade assembly on a flat, level surface.
Once you have inspected all parts and removed all packaging materials,
your snowplow is ready to be fully assembled.
Pallet Wrap End Panel
The tear resistant woven polyethylene pallet wrap
contains a moisture barrier to help protect all
packaged components and keep out the most
inclement weather during shipping and storage.
The end panel of the pallet cover contains impor-
tant information regarding the snowplow model
and the plow’s serial number. Both of these num-
bers are given together. The first three digits, and
two letters, of the number indicated is always the
plow model – 810SS and the entire ten digit num-
ber make up the serial number. The shipping
document is also attached to the end panel. Be
sure to retain this list for your records.
Snowplow Serial Number
Telephone Number
Dealer/Distributor
Date of Purchase
Moldboard Assembly 05
Moldboard Assembly
1. Begin the moldboard assembly by first removing each dust cap from
both of the SLIDE BOX CYLINDERS located at the center/rear of the
MOLDBOARD. Attach one 7/16"-20 x 9/16"-18 MALE O.R.B. CON-
NECTOR to each of the retract ports (#7 & #10) and one 9/16"-18 x
9/16"-18 MALE O.R.B. CONNECTOR to each of the extend ports (#8
& #9). Review the diagram below. Note: All of the hydraulic adapters
can be found packaged with the manifold assembly. Reference the
table on page 13 for proper torque specifications.
2. Connect the hoses to each of the hydraulic adapters on the cylinders.
Ports #7 & #10 receive a 1/4" x 36" HYDRAULIC HOSE (P/N 60019).
Note: Review the label on each hose for the appropriate part number.
Ports #8 & #9 receive a 3/8" x 36" HYDRAULIC HOSE (P/N 60224).
3. Next, position the PIVOT BEAM and the A-FRAME, near the mount
locations at the rear of the blade, between the two center support ribs.
Place the right and left group of hydraulic hoses (connected to the slide
box cylinders) through the 1-1/2" diameter rubber grommet openings
in the front face of the pivot beam.
4. Position the pivot beam between the two support ribs until the con-
necting points on the beam align with those on the plow. Insert one
3/4" DIA. x 3" CLEVIS PIN through each mounting hole and secure
them with one 1/4" DIA. x 1-1/2" COTTER PIN.
5. Hook each EXTENSION SPRING to the receiving holes located on
the pivot beam and connect the opposite end of the spring to their
respective SPADE BOLTS. Install the 5/8"-11 x 6-3/8" spade bolts
through the EXTENSION SPRING MOUNTING ANGLE on the top rear
of the blade. Secure each spade bolt by placing one 5/8" flat washer
on the bolt and thread one 5/8"-11 nylon insert lock nut. Tighten each
lock nut until a piece of paper can pass between the 3th & 4th coils
on the spring.
6. Install the flexible BLADE GUIDES at each end of the moldboard.
Insert the 5/16"-18 x 1" hex head cap screw through the holes at the
top of the wing reinforcement rib. Tighten all screws using the nylon
insert lock nuts provided.
Congratulations! You have successfully completed the first stage of
assembly for the Blizzard Power Plow Model 810SS. In the next section
you will assemble the A-frame and the components that are attached to it.
Rod
#7
Base
#8 #9
Base
#10
Rod
DRIVER’S SIDE PASSENGER’S SIDE
Male O.R.B. Connector Adapter
(Ports #7 & #10)
Male O.R.B. Connector Adapter
(Ports #8 & #9)
7/16" 9/16" 9/16" 9/16"
Printed
Label
All of the hoses shipped with the snowplow con-
tain a printed label (with a part number) applied
to the hose. Install the following hoses to their
respective ports on the manifold:
Hose P/N 60091 Ports #1 & #2
Hose P/N 60019 Ports #7 & #10
Hose P/N 60224 Ports #8 & #9
Note: See diagram on page 6.
06 A-frame Assembly
A-frame Assembly
For your convenience, the MANIFOLD and ANGLE CYLINDERS have
been secured to the A-FRAME at the factory; however, each contain
several components you will need to install.
1. Begin the assembly by first removing the A-FRAME COVER. Remove
each of the 3/8"-16 x 1-1/2" hex cap screws and washers from the
cover to gain access to the hydraulic manifold.
2. Each of the 6 HOSE PORTS receive a HYDRAULIC ADAPTER (see
illustrations to the left). Once the adapters have been installed, con-
nect the HYDRAULIC HOSES. Route each hose grouping from the
pivot beam to the access holes located on the sides of the A-frame.
Connect the hydraulic hoses to their respective adapters on the man-
ifold. Reference the table on page 13 for proper torque specifications.
Note: All ports are identified by a stamped number on the manifold. The
numbers also identify the hydraulic functions, which can be referenced
on the label under the A-frame cover (shown below).
9/16"
9/16"
90˚ Adjustable Elbow O.R.B. Adapter
(Left & Right Angle Cylinders)
9/16" 9/16"
7/16" 9/16"
Male O.R.B. Connector Adapter
(Port #1, #2, #8 & #9)
Male O.R.B. Connector Adapter
(Port #7 & #10)
The Hydraulic Valve & Hose Port Identification
Guide (right) is located under the A-frame cover.
3. Next, remove each dust cap from both of the hydraulic angle cylinder
ports and attach one 9/16"-18 x 9/16"-18 90˚ ADJUSTABLE ELBOW
O.R.B. ADAPTER to each port. Note: The cylinder ports should be
facing away from the A-frame. Each adapter should be angled toward
the top of the moldboard. Review the torque specifications chart on
page 13. Connect one 3/8" x 24" hydraulic hose (P/N 60091) to each
angle cylinder adapter.
Electrical Assembly - Control Wire Harness 07
Be careful not to overtighten the hose connections. Complete the
hose installation by running each hose through the access holes in
the A-frame to their respective manifold ports.
4. The PRESSURE & TANK HYDRAULIC HOSES attach to the ports on
the side of the manifold labeled “P” and “T”. Verify that the 3/4" x 78"
hydraulic hose with the 1-1/16"-12 female swivel is attached to the
1-1/16"-12 x 1-1/16"-12 MALE O.R.B. CONNECTOR ADAPTER
located in the pressure port (“P”). The 3/4" x 78" hydraulic hose, with
the male O.R.B. 90˚ swivel, connects to the tank port (“T”). Once you
have completed the installation of the hydraulic hoses, begin to install
the wire harness.
When handling the hydraulic manifold DO NOT
hold the manifold by the wire lead coils. The sole-
noid cartridges can bend, causing them to stick
when activated. Always carry the manifold by the
sides of the aluminum block.
Electrical Assembly - Control Wire Harness
1. Begin the installation by connecting the MALE ELECTRIC CONNEC-
TOR found on the COIL WIRE HARNESS (on manifold) to the FEMALE
ELECTRIC CONNECTOR on the WIRE HARNESS EXTENSION
(PLOW). Once both connectors are locked together, feed the opposite
end of the wire harness extension through the top access hole (same
as 3/4" tank hydraulic hose) in the A-frame located on the driver’s side.
2. Locate the GROUND END RING TERMINAL on the coil wire harness
and wire harness extension. Using a 3/8"-16 x 1-1/2" hex cap screw
and 3/8" tooth lock washer, ground both wires to the A-frame. Secure
the wires using a 3/8" top lock nut. Review the diagram below for the
proper ground location.
3. Next, connect the MOLDED RUBBER CONNECTOR from the wire
harness extension (plow) to the connector on the WIRE HARNESS
EXTENSION (VEHICLE). Lock together the remaining male electric
connector on the PISTOL GRIP CONTROL HARNESS to the female
electric connector on the wire harness extension (vehicle). Complete
the electrical assembly by attaching the BLACK, GROUND wire from
the wire harness extension to the cab of the skid steer. The PINK/
BLACK POWER wire connects to a switched (on and off with ignition)
power source with a minimum of 12 volts.
Manifold Mount Holes
There are three sets of holes in the bottom plate
on the A-frame. Each set is used for specific
model year snowplow components. The CLEAR
anodized manifold (2003) uses the center most
hole and the slotted hole to mount the manifold.
The hole opposite from the slotted hole serves as
the location for the ground stud. Use a 3/8"-16 x
1-1/2" bolt, tooth lock washer and 3/8"-16 top lock
nut to secure the electrical grounds to the A-frame.
Hydraulic manifold
(clear anodized)
mount holes
Hole location for
3/8"-16 x 1-1/2"
ground bolt
The Model 810SS control wire harness is pack-
aged with a stainless steel mount bracket (P/N
70040). Use the bracket to secure the wire har-
ness extension (vehicle) to the skid steer.
Position the bracket in the notch provided on the
molded rubber connector and mount it to the skid
steer. Locate the bracket in an accessible location
for easy on-and-off installation of the harness.
08 Testing The Snowplow
4. Complete the assembly by attaching the A-frame cover. Align the
holes in the cover with those on the A-frame and secure it with
3/8"-16 x 1-1/2" hex cap screws and 3/8" washers.
Congratulations! You have just completed building the finest snowplow
skid steer attachment available! However, the snowplow’s functions still
need to be tested.
Testing The Snowplow
1. To test all of the functions on the Power Plow, your snowplow needs
to be properly attached to the skid steer. Follow the mounting proce-
dure on page 9.
2. Once the skid steer plate and the UNIVERSAL MOUNT PLATE on the
A-frame have been locked together (using the locking levers on the
skid steer), complete the hydraulic connections with the skid steer
turned off. Note: Due to the various make and model skid steer avail-
able, hydraulic couplings for the auxiliary hydraulic connections are
not provided. Consult your skid steer’s Operation Manual for the
appropriate couplings needed. Once you have identified the appro-
priate hydraulic couplings for your skid steer, make the connections to
both of the 3/4" x 78" hydraulic hoses provided. The hydraulic hose
with the female swivel is attached to the male adapter connector
located in the pressure port (“P”) on the manifold. The remaining
hydraulic hose with the 90˚ swivel is attached to the tank port (“T”).
Complete the hydraulic installation by making the appropriate connect-
ions at the skid steer.
WARNING: Always use caution when connecting high-
pressure hydraulic fittings. Hydraulic fluid under pressure
can puncture skin causing serious injury or death. In the
event of a hydraulic leak, relieve hydraulic pressure before
loosening fittings. If injured, seek emergency medical help
immediately.
3. Start the skid steer and begin to initiate the Power Plow’s blade func-
tions. Note: Depending on the skid steer model, it may be necessary
to turn on the skid steer’s auxiliary hydraulic switch prior to operating
the plow. The left switch operates the DRIVER’S SIDE WING. Push
the switch UP to EXTEND the wing and DOWN to RETRACT the
wing. Push the center switch UP to LEFT ANGLE the snowplow and
DOWN to RIGHT ANGLE. The right switch operates the PASSENGER’S
SIDE WING. Again, pushing up will extend the wing and down will
retract the wing. Upon initiating the switches on the pistol grip control,
you may notice a plow function is slow or delayed. The hydraulic fluid
is filling the cylinders and replacing air in the system. If necessary,
monitor the hydraulic fluid level in your skid steer. Also, look for any
leaks around the manifold, hydraulic hoses and all cylinders.
Congratulations on a successful assembly and installation! Once all of the
blade functions have been tested, your Blizzard Power Plow is ready for
action. Should you need additional support during a plow assembly, con-
tact your local authorized Blizzard dealer.
BC
A
810SS Pistol Grip Control Functions
There are three switches that operate all of the
810SS Power Plow blade functions:
(A) DRIVE. BOX: UP-Extend, DOWN-Retract
(B) ANGLE: UP-Left, DOWN-Right
(C) PASS. BOX: UP-Extend, DOWN-Retract
Pistol Grip Control Mount Bracket
The bracket is designed to mount in a variety of
positions (see hole placement above). Use the
hardware provided to secure the bracket to the
skid steer.
Position the pistol grip control into the bracket
and “twist-lock” it into place. Depending on oper-
ator preference, the control can be mounted
vertically or horizontally.
Note: Some skid steer models have safety
devices that rotate in front of the operator when
seated. Do not install the mount bracket such that
it interferes with the operation of these devices.
Mounting & Dismounting Instructions 09
Mounting & Dismounting Instructions
Plow Attachment Lever
Receiving
Holes
A
B
B
C
SKID STEER MOUNTING &
DISMOUNTING INSTRUCTIONS
MOUNTING
1. Position the skid steer close to the snowplow attachment and align the mount
points on the skid steer plate to those on the plow attachment plate.
2. Tilt the skid steer plate forward and position the top edge of the plate under
the receiving pocket on the top edge of the snowplow attachment plate.
CAUTION: Keep fingers away from skid steer mounting points. Slightly
raise the arms on the skid steer and tilt the skid steer plate toward the cab.
The snowplow attachment should now be flush with the skid steer mount.
3. Engage both locking levers on the skid steer by rotating each handle 90˚ into
a horizontal position. The attachment is now properly fastened to the skid steer.
4. Proceed to attach both 3/4" diameter hydraulic hoses from the manifold to
the auxiliary hydraulic connections located on the skid steer. Note: Depending
on the skid steer model, it may be necessary to initiate an auxiliary hydraulic
switch on the skid steer prior to operating the plow.
5. Complete the mounting procedure by attaching the electrical connection on
the wire harness to the auxiliary electrical connection on the skid steer.
DISMOUNTING
1. Lower the attachment on a flat, level surface and turn the engine off.
2. Disconnect the electrical connection at the auxiliary power location.
3. Disconnect both 3/4" diameter hydraulic hoses from the auxiliary hydraulic
connectors.
4. Disconnect the snowplow attachment by rotating both of the locking levers
90˚ until they are in the vertical position.
5. Start engine and slowly tilt the skid steer plate forward until the top edge of
the plate clears the plow attachment plate.
6. Back skid steer away slowly – The disconnect procedure is now complete.
WARNING: Read and understand all warning labels prior
to operating your skid steer attachment. Failure to follow
this instruction may result in serious injury or death.
Skid steer plate attaches under the
top lip of the snowplow attachment.
With the attachment flush to the
skid steer plate, engage both lock-
ing levers on the skid steer. Rotate
each handle 90˚ into a horizontal
position. The levers will slide through
the receiving holes in the snowplow
attachment plate. The plate is now
securely mounted to the skid steer.
Connect both hydraulic hoses & the
electrical harness to the skid steer.
C
B
A
BLZ 1014
Prior to operating your Power Plow, review the Mounting & Dismounting
Instructions label at the driver’s side rear of the moldboard (shown below).
Should the Mounting & Dismounting Instructions
label or any of the labels that came with your
snowplow become hard to read or wear off, contact
your local dealer or call our authorized Blizzard
dealer for replacements.
10 Regular Maintenance
Regular Maintenance
Your Blizzard Power Plow snowplow has been designed for years of
rugged, dependable service with low maintenance. To ensure proper
working condition, follow the maintenance guidelines below and on the
next page.
CAUTION: Always follow the maintenance guidelines in a timely
fashion. Failure to observe maintenance guidelines may result
in poor snowplow operation, increased component wear or
possibly lead to part failure.
Routinely inspect the following items – perform maintenance as needed:
1. All fasteners, pins, nuts and bolts for tightness. See the recommended
maximum bolt torque chart on page 13.
2. All hydraulic hoses and hydraulic hose adapters for wear and leaks.
See the recommended hydraulic adapter torque values on page 13.
3. All cylinders for leaks; inspect rod ends for corrosion and pitting.
4. Cutting edges and plow shoes for wear. Do not discard plow shoe
washers. These should be retained for different shoe adjustments.
5. Clean and lubricate the male and female electric connectors on the
pistol grip wire harness periodically. Apply dielectric grease for every
25 hours of snowplow use. You may need to grease more frequently
depending on your plowing environment.
6. Lubricate all pins and bushings to prevent corrosion and to maintain
consistent operation. The inner slide boxes should also be lubricated
to provide free travel. A NLGI Grade 2 multipurpose lithium complex
grease with molybdenum (MPGM) is recommended for lubrication.
7. Clean and cover deep scratches or exposed metal with Blizzard Snow-
plow white (P/N 61219) or black (P/N 63073) touch-up paint. Contact
your local Blizzard dealer for availability.
8. Monitor the hydraulic fluid level in your skid steer periodically.
9. Check the trip spring adjustment. Properly adjusted tension will allow
a sheet of paper to pass between the 3rd and 4th coils of the spring.
10. Each wing uses one extension spring to help return it from the forward
or scoop position. Adjust the tension on the installed spring as needed
or install and optional second extension spring for increased return
speed.
Maintenance Schedule
Maintenance Performed Date
Storing Your Snowplow 11
Storing Your Snowplow
Placing Your Plow In Storage
1. Position your plow on a flat, level surface for storage. Follow the dis-
mounting procedure illustrated on page 9.
2. Pressure wash and dry the entire snowplow prior to placing in storage.
3. Apply a liberal amount of white lithium grease to the male and female
electric connectors on the pistol grip wire harness.
4. Lubricate all exposed hydraulic cylinder rod ends with liquid white
lithium grease to prevent corrosion.
5. Lubricate all pins and bushings to prevent corrosion and to maintain
consistent operation, including the inner slide boxes. A NLGI Grade 2
multipurpose lithium complex grease with molybdenum (MPGM) is
recommended for lubrication.
6. Clean and cover deep scratches or exposed metal with Blizzard Snow-
plow white (P/N 61219) or black (P/N 63073) touch-up paint. Contact
your local Blizzard dealer for availability.
7. Change the hydraulic oil fluid in your skid steer as indicated by the
maintenance table in your skid steer Owner’s Manual. It is recom-
mended that the fluid in the snowplow attachment be replaced annually
and the hydraulic pump filter on the skid steer be cleaned.
8. Cover the snowplow with a tarp if stored outside. This will protect your
plow from sun fading and inclement weather which can lead to
accelerated corrosion.
Removing Your Plow From Storage
1. Perform all regular maintenance indicated on the previous page.
2. If you have not replaced the hydraulic fluid in the snowplow’s hydraulic
system, it is strongly encouraged that you do so prior to operating your
plow.
3. Follow the mounting procedure illustrated on page 9.
4. Once the plow has been properly mounted to the skid steer and all
electrical connections have been made, initiate all of the functions of
the snowplow. Monitor the fluid level in the skid steer periodically.
Annual Fluid Replacement
Type & Quantity of Fluid Replaced Date
12 Plow Specifications
Moldboard
Length ......................................................................................8'
Thickness ....................................................................12 Gauge
Height ....................................................................................31"
Reinforcement ......................................................4 Ribs @ 1/4"
Cutting Edge ......................................................1/2" x 6" (1080)
Finish..........................................................Powder Coat - White
Wings
Length ....................................................................................12"
Thickness ....................................................................11 Gauge
Height ....................................................................................31"
Reinforcement ..............................................1 Rib each @ 1/4"
Cutting Edge ........................................................1/4" x 10" (T1)
Finish..........................................................Powder Coat - White
Trip Mechanism
Tr ip Spring Type ................................(4) 3/8" Hooked Extension
Tr ip Spring Adjust. ........................5/8"-11 x 6-3/8" Spade Bolts
A-frame
Material ..................................................1/4" & 5/16" Mild Steel
Cover ..................................1/4" Mild Steel w/Non-Skid Texture
Finish..........................................................Powder Coat - Black
Manifold
Construction ......................................Clear Anodized Aluminum
Ports..........................................................................................8
Cartridge Valves........................................................................6
Relief/Anti-Cavitation Valves ....................................................5
Check Valves ............................................................................4
Pressure Compensation Regulation Valve................................1
Weight ..........................................................................19.66 lb.
Mount..................................A-frame Install w/Hex Head Screws
Cylinders
Angle Cylinders ................................................................................2
Stroke ............................................................................................10"
Ram Diameter............................................................................1-3/4"
Bore Diameter..................................................................................2"
Slide Box Cylinders ..........................................................................2
Stroke ..................................................................................13-15/16"
Ram Diameter ..................................................................................1"
Bore Diameter............................................................................1-1/2"
Miscellaneous
Plow Weight ................................................................Approx. 950 lb.
Compact Plow Width ........................................................................8'
WidePass™ Plow Width ................................................................10'
BucketBlade™ Plow Width ..........................................................9'-3"
Adjustable Plow Shoes..............................(2) Heavy-Duty Cast Steel
Mount Mechanism....................................Universal Attachment Plate
Standard Control Station ..............................Pistol Grip w/3 Switches
Integrated Control (Optional) ..................................Auxiliary Harness
Anti-Trip (Optional) ......................................One Piece Trip-Lock Bar
All specifications are for the Model 810SS Blizzard Power Plow snowplow.
Blizzard Corporation reserves the right, under its Continuous Improvement Policy, to change
construction or design details and furnish equipment when so altered without reference to
illustrations or specifications.
Plow Specifications
Torque Specifications 13
1. Make sure the tubing and threads are clean.
2. Lubricate the threads with 10W hydraulic oil.
3. Hand tighten the nut/sleeve to appox. 30 in-lbs.
4. Make alignment marks on the nut and fitting.
5. Proceed to tighten to turns or ft-lb values.
6. When fully tightened make a 2nd set of align-
ment marks at the fully tightened position.
Note: Torque values specified are for threads
lubricated with 10W hydraulic oil.
Sizes -02 through -08 are less tolerant to over-
torque abuse. This will reduce the clamping force
resulting in loss of seal and reduction in flow.
37˚ JIC Flare Torque Values
Turns Size ft-lbs min./max. Assembly Steps w/Visual Check
N/A -02 6 - 7
N/A -03 8 - 9
2-04 11 - 12
2-05 14 - 15
1-1/2 -06 18 - 20
1-1/2 -08 36 - 39
1-1/2 -10 57 - 63
1-1/4 -12 79 - 88
1-14 94 - 103
1-16 108 - 113
1-20 127 - 133
1-24 158 - 167
1-32 245 - 258
Metric Class 8.8 Metric Class 10.9
Tightening Torque Tightening Torque
“Lubricated” “Dry” “Lubricated” “Dry”
56177 4.63 N-m 6.18 N-m 5 8840 6.63 N-m 8.84 N-m
68743 7.87 N-m 10.5 N-m 6 12512 11.3 N-m 15.0 N-m
712570 13.2 N-m 17.6 N-m 7 17990 18.9 N-m 25.2 N-m
815921 19.1 N-m 25.5 N-m 8 22784 27.3 N-m 36.5 N-m
10 25230 37.8 N-m 50.5 N-m 10 36105 54.1 N-m 72.2 N-m
12 36670 66.0 N-m 88.0 N-m 12 52475 94.5 N-m 125 N-m
14 50025 105 N-m 140 N-m 14 71587 150 N-m 200 N-m
16 70650 170 N-m 226 N-m 16 97732 235 N-m 313 N-m
18 86400 233 N-m 311 N-m 18 119520 323 N-m 430 N-m
20 110250 330 N-m 441 N-m 20 152513 458 N-m 610 N-m
Torque Specifications
SAE J429 - Grade 5 SAE J429 - Grade 8
Tightening Torque Tightening Torque
“Lubricated” “Dry” “Lubricated” “Dry”
1/4-20 2,000 75 in-lbs 100 in-lbs 1/4-20 2,850 107 in-lbs 143 in-lbs
5/16-18 3,350 157 in-lbs 210 in-lbs 5/16-18 4,700 220 in-lbs 305 in-lbs
3/8-16 4,950 23 ft-lbs 31 ft-lbs 3/8-16 6,950 32.5 ft-lbs 44 ft-lbs
7/16-14 6,800 37 ft-lbs 50 ft-lbs 7/16-14 9,600 53 ft-lbs 70 ft-lbs
1/2-13 9,050 57 ft-lbs 75 ft-lbs 1/2-13 12,800 80 ft-lbs 107 ft-lbs
9/16-12 11,600 82 ft-lbs 109 ft-lbs 9/16-12 16,400 115 ft-lbs 154 ft-lbs
5/8-11 14,500 113 ft-lbs 151 ft-lbs 5/8-11 20,300 159 ft-lbs 21 ft-lbs
3/4-10 21,300 200 ft-lbs 266 ft-lbs 3/4-10 30,100 282 ft-lbs 376 ft-lbs
7/8-9 29,435 321 ft-lbs 430 ft-lbs 7/8-9 41,550 454 ft-lbs 606 ft-lbs
1-8 38,600 482.5 ft-lbs 640 ft-lbs 1-8 54,540 680 ft-lbs 900 ft-lbs
Clamp Loads
(lbs.)
Clamp Loads
(lbs.)
Nominal
Thread
Size
Nominal
Thread
Size
Grade Identification Marking for J429 - Grade 5 Bolt
•Material: Medium carbon steel: quenched and tempered
•Minimum Proof Strength: 85,000 psi
•Minimum Tensile Strength: 120,000 psi
•Core Hardness Rockwell (min.): C25, (max.): C34
• Minimum Yield Strength: 92,000 psi
Grade Identification Marking for J429 - Grade 8 Bolt
•Material: Medium carbon alloy steel:quenched and tempered
•Minimum Proof Strength: 120,000 psi
•Minimum Tensile Strength: 150,000 psi
•Core Hardness Rockwell (min.): C33, (max.): C39
• Minimum Yield Strength: 130,000 psi
8.8
Clamp Loads
(Newton)
Clamp Loads
(Newton)
Diameter
(millimeters)
Diameter
(millimeters)
Grade Identification Marking for Metric - Grade 8.8 Bolt
•Material: Medium carbon steel: quenched and tempered
•Minimum Proof Strength: 580 MPa
•Minimum Tensile Strength: 800 MPa
•Core Hardness Rockwell (min.): C22, (max.): C32
•Minimum Yield Strength: 640 MPa
10.9
Grade Identification Marking for Metric - Grade 10.9 Bolt
•Material: Low carbon alloy steel: quenched and tempered
•Minimum Proof Strength: 830 MPa
•Minimum Tensile Strength: 1040 MPa
•Core Hardness Rockwell (min.): C32, (max.): C39
•Minimum Yield Strength: 940 MPa
O-Ring Boss Torque Values
Size ft-lbs min./max. O-Ring Boss Assembly
-02 6 - 7
-03 8 - 10
-04 13 - 15
-05 17 - 21
-06 22 - 25
-08 40 - 43
-10 43 - 57
-12 68 - 75
-14 90 - 99
-16 112 - 123
-20 146 - 200
-24 154 - 215
-32 218 - 290
1. Verify the port, O-ring, sealing surfaces, and threads are
clean and free of damage.
2. Lubricate the threads and the O-ring with 10W hydraulic oil.
3. For an adjustable O.R.B., completely back-off the lock nut
and the washer.
4. Hand tighten the fitting until it contacts the port spotface.
Point the elbow or tee in the desired direction and hold.
5. Proceed to tighten to the proper specified torque value.
Note: Torque values specified are for threads lubricated
with 10W hydraulic oil.
Disclaimer: All torque values included in the charts above are advisory only, and their use by anyone is entirely voluntary. Reliance on the contents for any purpose by anyone is the sole risk of that person and Blizzard Corporation is not responsible for any loss, claim or damages
arising therefrom. Blizzard Corporation has made an effort to present the above contents accurately, but we do not guarantee its completeness or validity. This information is subject to change at any time, without notice. Blizzard Corporation makes no representations or warranties,
express or implied, in connection with the information.
Ref. Part Qty. Part Description
No. Number
152074 1 Moldboard Weldment
261170 1 Label, WARNING! (BLZ 1013)
361082 1 Decal, Center Moldboard (BLZ 1000)
461171 1 Label, Skid Steer Mounting & Dismounting Instructions (BLZ 1014)
561292 1 Cutting Edge (1080), Moldboard
661196 7 Bolt, Carriage, 1/2"-13 x 1-1/2" Grade 8 P
761365 13 Nut, Flanged Lock, 1/2"-13
851042 1 Wing Weldment, Driver’s Side
961083 1 Decal, Wing, Driver’s Side (BLZ 1002)
10 51048 1 Cutting Edge Weldment (T1), Wing, Driver’s Side
11 50057 1 Slide Box Weldment, Driver’s Side
12A 61220 2 Plow Shoe Assembly, Heavy-Duty Cast Iron (8-3/8" Shaft): (1) - 12, 14, (18) - 13
12 61102 2 Spacer, 1-1/8" I.D., 1-5/8" O.D. x 1-1/2" YZ
13 61101 36 Washer, Flat, 1", 1-1/016" I.D., 1-3/4" O.D. YZ
14 61103 2 Pin, Linch, 7/16" x 1-3/4" YZ
15 63063 1 Label, Serial Number, Sequentially Numbered (BLZ 1049)
16 61383 4 Screw, Hex Head Cap, 5/16"-18 x 2-1/4" Grade 8 YZ
17 11871 4 Pin, Slide Box Stop, 1" DIA. x 4-3/4" (with 3/8" DIA. hole)
18 61384 4 Nut, Top Lock, 5/16"-18 Grade C Z
19A 61049 2 Plow Guide Assembly: (2) - 19 & 20
19 61051 4 Screw, Hex Head Cap, 5/16"-18 x 1" Grade 5 Z
20 61052 4 Nut, Nylon Insert Lock, 5/16"-18 Z
21 51043 1 Wing Weldment, Passenger’s Side
22 61084 1 Decal, Wing, Passenger’s Side (BLZ 1001)
23 51047 1 Cutting Edge Weldment (T1), Wing, Passenger’s Side
24 61418 2 Bolt, Carriage, 1/2"-13 x 3-1/2" Grade 8 P
25 61419 2 Bolt, Carriage, 1/2"-13 x 4-1/2" Grade 8 P
26 61361 2 Bolt, Carriage, 1/2"-13 x 5-1/2" Grade 8 P
27 50058 1 Slide Box Weldment, Passenger’s Side
28 61416 2 Bolt, Spade, 5/8"-11 x 7-3/8" Grade 8 Z
29 61398 2 Spring, Extension, 13" O.A.L. x 2" O.D. x 5/16"
30 61385 2 Pin, Clevis, 5/8" DIA. x 3" YZ
31 61028 2 Pin, Spring, 1/4" DIA. x 1-1/4"
32 51009 2 Pin, Wing / Slide Box Pivot, 3/4" DIA. x 9"
33 61425 2 Plug, 2-51/64" O.D., 2-9/32" I.D. x 1/2" Black Polyethylene
34 14622 2 Hydraulic Cylinder, Slide Box Extend/Retract
35 61063 2 Nut, Top Lock, 5/8"-11 Grade C Z
36 60007 6 Hydraulic Adapter, 9/16"-18 x 9/16"-18 Male O.R.B. Connector
37 60224 2 Hydraulic Hose (Ports #8 & #9), 3/8" x 36" - Slide Box Extend
38 60003 4 Hydraulic Adapter, 7/16"-20 x 9/16"-18 Male O.R.B. Connector
39 60019 2 Hydraulic Hose (Ports #7 & #10), 1/4" x 36" - Slide Box Retract
40 61198 2 Cap, 5/8" I.D., 3/4" O.D. x 1", Black Vinyl
41 11989 2 Pin, Hydraulic Cylinder Base End, 5/8" DIA. x 11-1/2" (with 1/4" DIA. hole) - Slide Box Extend/ Retract
42 61030 2 Pin, Hair Cotter, 1/8" DIA. x 2-5/8" Z
43 61099 4 Spring, Extension, 15-1/4" O.A.L. x 2-3/8" O.D. x 3/8"
44 61187 4 Bolt, Spade, 5/8"-11 x 6-3/8" Grade 8 Z
45 61064 4 Washer, SAE Mil Carb High-Strength, 5/8", 1-5/16" O.D., 21/32" I.D. YZ
46 61188 4 Nut, Nylon Insert Lock, 5/8"-11 Type NE
47 41041 1 Pivot Beam Weldment
48 50069 2 Pin, Clevis, 3/4" DIA. x 3" YZ
49 61357 6 Pin, Cotter, 1/4" x 1-1/2" Z
50 41051 4 Pin, Clevis, 3/4" DIA. x 5" YZ
51 61330 1 Screw, Hex Head Cap, 1"-8 x 9" (with 7-3/4" Shank) Grade 8 P
52 61008 1 Nut, Top Lock, 1"-8 Grade C Z
53 61217 4 Grommet, 1-1/2" I.D., 2-1/8" O.D. Black Rubber, 60 Durometer
54 60029 2 Hydraulic Cylinder, Plow Angle
55 60091 2 Hydraulic Hose (Ports #1 & #2), 3/8" x 24" - Plow Angle
56 60005 2 Hydraulic Adapter, 9/16"-18 x 9/16"-18 90˚ Adjustable Elbow O.R.B.
57A 70045 1 A-frame Cover Assembly: (1) - 57-59
57 70041 1 Cover, A-frame
58 63068 1 Label, Sequence Valve & Hydraulic Hose Identification Guide (BLZ 1052)
59 70021 1 Grip, Non-skid, Rubber
60 61016 11 Washer, SAE Mil-Carb High-Strength, 3/8", 13/16" O.D., 13/32" I.D., YZ
61 61328 8 Screw, Hex Head Cap, 3/8"-16 x 1-1/2" Grade 8 YZ
62A 70044 1 A-frame Assembly: (1) - 57A, 62, 69, (2) - 67, (7) - 60, 61, 68
62 70043 1 A-frame Weldment
63 61313 2 Screw, Hex Head Cap, 3/8"-16 x 3-3/4" Grade 8 YZ
64 61307 1 Washer, Internal/External Tooth Lock, 3/8"
65 61034 3 Nut, Top Lock, 3/8"-16 Grade C Z
66 61222 2 Washer, Split Lock, 3/8" YZ High-Alloy
Note: The reference numbers listed
identify parts shown in the illustration
on pages 16-18. These numbers are
specific to these illustrations only and
do not correspond with other diagrams
in the manual. Always review the part
number given for proper component
identification.
MODEL 810SS PARTS LIST
Moldboard & Wing Assembly Parts
Pivot Beam & A-frame Assembly Parts
14 Parts List (1 of 2)
Parts List (2 of 2) 15
Ref. Part Qty. Part Description
No. Number
67 61366 2 Grommet, 1-15/16" I.D., 2-5/8" O.D. Black Rubber, 60 Durometer
68 61275 7 U-Nut, 3/8"-16
69 61085 1 Decal, Blizzard Snowplows, 2-1/4" x 13-7/8" (BLZ 1003)
70 60086 1 Hydraulic Hose, 3/4" x 78" - 1-1/16"-12 Female Swivel / 3/4"-14 Male Pipe Str.aight, Pressure Port “P”
71 60087 1 Hydraulic Hose, 3/4" x 78" - 1-1/16"-12 Male O.R.B.90˚ Swivel/ 3/4"-14 Male Pipe Straight, Tank Port “T”
72A 60268 1 Hydraulic Manifold Assembly: (1) - 72-74, 78A, 81, 82, (2) - 38, 77, 83, 84, 60322, (4) - 36, 75, 76, (5) - 79
72 60267 1 Manifold Block (with Cross Port Relief) Clear Anodized Aluminum (30102904)
73 60089 1 Hydraulic Adapter, 1-1/16"-12 x 1-1/16"-12 Male O.R.B. Connector
74 60183 1 Valve, Pressure Compensation Regulation (88400015)
75 60225 4 Valve, Check, 50 PSI (86020028)
76 60166 4 Valve, Spool, Three-Way, Two Position (86020195 w/o screen)
77 60278 2 Valve, Relief, 1700 PSI (85020411 tamper proof)
78A 62161 1 Coil Harness Assembly: (1) - 62045, 62118, (2) - 80, (3) - 62116, (5) - 78, (7) - 62096 & 62097
78 62163 5 Coil, PDL, 12V DC (38400066)
79 60052 5 Nut, Hex Jam, 1/2"-20 YZ
80 62164 2 Coil, LDL, 12V DC (63900506)
81 60321 1 Valve, Spool, Four-Way, Three Position (85020081 w/o screen)
82 60168 1 Valve, Relief, 3000 PSI (85020340)
83 60049 2 Plug, #4 SAE (61010016)
84 60279 2 Valve, Relief, 1500 PSI (85020410 tamper proof)
85 60320 1 Valve, Spool, N.O. (86020193)
N/A 60322 2 Piston Assembly (34952125)
86A 62131 1 Pistol Grip Control Wire Harness Assembly: (1) - 86, 87 & 62132-62135
86 62082 1 Wire Harness, Pistol Grip
N/A 62132 1 Wire Harness Extension, Vehicle Side
N/A 62133 1 Weather Cap, Molded Rubber, Female (Wire Harness Extension, Vehicle Side)
87 70040 1 Mount Bracket, Wire Harness Extension, Vehicle Side
N/A 62134 1 Wire Harness Extension, Plow Side
N/A 62135 1 Weather Cap, Molded Rubber, Male (Wire Harness Extension, Plow Side)
N/A 62045 2 Connector, Electric, Male, Plastic
N/A 62097 17 Terminal, Male (18-16 AWG)
N/A 62096 35 Seal, Cable, Silicone, Orange (18 AWG)
N/A 62116 5 Plug, Cavity, Silicone, White (18-16 AWG)
N/A 62046 2 Connector, Electric, Female, Plastic
N/A 62100 2 Terminal, Ring, #10 (22-18 AWG)
N/A 62093 18 Terminal, Female (18-16 AWG)
N/A 62118 1 Terminal, End Ring, 3/8" I.D. Zinc, 6 Gauge (Coil Harness)
N/A 62072 1 Terminal, End Ring, 3/8" I.D. Copper, 4 Gauge (Wire Harness Extension, Plow Side)
88A 70048 1 Pistol Grip Control Mount Bracket Assembly: (1) - 88, (2) - 60, 89 & 90
88 70049 1 Mount Bracket, Pistol Grip Control
89 61214 2 Screw, Hex Head Cap, 3/8"-16 x 1-1/4" Grade 8 YZ
90 61014 2 Nut, Jam Nylon Insert Lock, 3/8"-16 Z, Type NTE
N/A 61277 1 Kit, Hardware, Snowplow Assembly Parts: (1) - 61, 64, 65, (2) - 48, 49, (4) - 44-46
N/A 60319 1 Kit, Hydraulic Adapter: (2) - 56, (4) - 38, (6) - 36
N/A 60323 1 Kit, Hydraulic Hose: (1) - 70 & 71, (2) - 37, 39 & 55
N/A 61430 1 Kit, Hardware, Moldboard Cutting Edge: (7) - 6 & 7
N/A 52067 1 Kit, Cutting Edge, Moldboard w/Hardware: (1) - 5, 61430
N/A 61431 1 Kit, Hardware, Wing Cutting Edge: (1) - 24-26, (3) - 7
N/A 51104 1 Kit, Cutting Edges, Wing w/Hardware: (1) - 8, 21, (2) - 61431
N/A 61321 1 Kit, Moldboard & Wing Cutting Edges w/Hardware: (1) - 52067, 51104
MODEL 810SS PARTS LIST
Pivot Beam & A-frame Assembly Parts (Continued)
Hydraulic Manifold Assembly Parts
Pistol Grip Control Wire Harness Assembly Parts
Miscellaneous Assembly Parts
2003 Blizzard® Power Plow® Snowplow Assembly Schematic - Model 810SS
Blizzard Corporation reserves the right, under its Continuous Improvement Policy, to change
construction or design details and furnish equipment when so altered without reference to
illustrations or specifications. Blizzard Corporation offers a one-year limited warranty for all
snowplows and accessories. Blizzard Corporation does not warranty non-Blizzard snowplow
service parts or accessories or damage resulting from the use of these unauthorized items.
The Blizzard Power Plow is protected by U.S. Patents 5,638,618 and 5,899,007. Other patents pending.
67
2
3
4
65
8
9
11
10
12A
12
13
14 16
17
1815
37
39
35
40
41
42
43
44
45
46
47
49
49
48
50
50
52
51
54
55 56
53
63
60
61
86A
86
49
72A - SEE DETAIL ON PAGE 18.
50
49
50
71
69
63
60
64
65
66
62A
62
57A
59
5758
61
60
68
65
88
89
60
90
88A
87
1
7
38
39
36
37
48
54
56
31
26
23
25 24
20
21
22
19
19A
7
28
35
27
30
29
32
33
34
55
70
49
50
7
4
18 Diagram - Hydraulic Manifold Detail
72 73
74
75
3638
75
76 76
76 76
77
77
78A
78
78
78
78 78
79
79
79
80
81 82
83
84
84
85
Coil Harness/Hydraulic Manifold Schematic 19
MODEL 810SS COIL HARNESS WIRE SCHEMATIC (2003)
MODEL 810SS HYDRAULIC MANIFOLD SCHEMATIC (2003)
S10
S4
S9 S1
A
B
C
D
E
F
G
H
J
K
CONNECTS TO C3
SEE SCHEMATIC ON PAGE 24.
S4
S3
S9
S10
S1
S2
N/A
N/A
S5
N/A
S3
S2
S5
RV1
1700 PSI
87
RV2
1500 PSI
LEFT SLIDE BOX
RIGHT ANGLE
LEFT ANGLE
129 10
CV1
50 PSI
CV2
50 PSI
RV4
1700 PSI
RV3
1500 PSI
CV3
50 PSI
CV4
50 PSI
RIGHT SLIDE BOX
S10 S2 S1S9
3000 PSI
RV5
S3 S4
.052
.110
P T
PC
50 PSI
S5
20 Diagram - Pistol Grip Control Wire Harness
NOTE: NO NUMBERS ON SWITCH
(USE THIS CHART TO FIND TOP)
PIN NO. COLOR AWG LENGTH
1BROWN18 6"
2 BLUE/BLACK 18 84"
3 PINK/BLACK 18 6"
4 PINK/BLACK 18 6"
5BROWN18 6"
6 BLUE/WHITE 18 84"
NOTE: NO NUMBERS ON SWITCH
(USE THIS CHART TO FIND TOP)
PIN NO. COLOR AWG LENGTH
1BROWN18 6"
2 GREEN 18 84"
3 PINK/BLACK 18 6"
4 PINK/BLACK 18 6"
5BROWN18 6"
6 BLUE 18 84"
810SS PISTOL GRIP CONTROL
WIRE HARNESS (2003)
P/N 62082
NOT DRAWN TO SCALE
UNLESS OTHERWISE SPECIFIED
ALL DIMENSIONS IN INCHES
A
BC
E
D
FGH
K
J
END VIEW
LOOKING AT CONNECTOR
PACKARD GT 280 ELECTRIC CONNECTOR
PIN COLOR FUNCTION AWG
NO.
A PINK/BLACK POWER 18
BBROWN PUMP SOLENOID 18
C BLACK GROUND (JUMPER) 18
D BLACK GROUND (JUMPER) 18
E GREEN RIGHT ANGLE 18
F BLUE LEFT ANGLE 18
G BLUE/BLACK DRIVE. SLIDE BOX RET. 18
H BLUE/WHITE DRIVE. SLIDE BOX EXT. 18
J RED/BLACK PASS. SLIDE BOX RET. 18
K RED/WHITE PASS. SLIDE BOX EXT. 18
(JUMPER)
DRIVE. SLIDE BOX
EXTEND (UP)
RETRACT (DOWN)
PLOW ANGLE
LEFT (UP)
RIGHT (DOWN)
PASS. SLIDE BOX
EXTEND (UP)
RETRACT (DOWN)
87"
JACKET MATERIAL
BLACK NYLON BRAID
6" 1"
LOCATION WHERE
BLACK (JUMPER)
WIRE RETURNS
TO CONNECTOR
HEAT AND CAP
BRAIDING END
PLASTIC ELECTRIC CONNECTOR - MALE (P/N 62045)
SILICONE RUBBER CABLE SEAL (18 AWG) - P/N 62096
MALE TERMINAL (18-16 AWG) - P/N 62097
C1 CONNECTS TO C2 ON PAGE 22.
BACK VIEW
OF SWITH #1
NOTE: ALL PINK/BLACK SPLICE TOGETHER & ALL BROWN SPLICE TOGETHER
SWITCH #1
NOTE: NO NUMBERS ON SWITCH
(USE THIS CHART TO FIND TOP)
PIN NO. COLOR AWG LENGTH
1BROWN18 6"
2 RED/BLACK 18 84"
3 PINK/BLACK 18 6"
4 PINK/BLACK 18 6"
5BROWN18 6"
6 RED/WHITE 18 84"
SWITCH #2 SWITCH #3
1
3
5
2
4
6
TOP
1
3
5
2
4
6
TOP
1
3
5
2
4
6
TOP
BACK VIEW
OF SWITH #2
BACK VIEW
OF SWITH #3
LOCATION OF
BROWN WIRE
SPLICE
BACK
BRAIDING
CATCH
STRAIN
RELIEF
TUBE
LOCATION OF
PINK/BLACK
WIRE SPLICE
Pistol Grip Control Harness Wire Schematic 21
810SS PISTOL GRIP CONTROL WIRE SCHEMATIC (2003)
DRIVE. SIDE RETRACT
DRIVE. SIDE EXTEND
SWITCH #3
BROWN
BLUE/BLACK
BLUE/WHITE
GREEN
RED/BLACK
BLUE
RED/WHITE
BLACK
BLACK
PINK/BLACK
LEFT ANGLE
RIGHT ANGLE
PASS. SIDE EXTEND
PASS. SIDE RETRACT
SWITCH #2
SWITCH #1
C1
22 Diagram - Wire Harness Extension (Vehicle)
810SS WIRE HARNESS EXTENSION
VEHICLE SIDE (2003)
P/N 62132
NOT DRAWN TO SCALE
UNLESS OTHERWISE SPECIFIED
ALL DIMENSIONS IN INCHES
MOLDED RUBBER CONNECTOR
PACKARD GT 280 ELECTRIC CONNECTOR
PIN COLOR FUNCTION AWG
NO.
A PINK/BLACK POWER (POSITIVE) 18
BBROWN PUMP SOLENOID 18
C BLACK GROUND (NEGATIVE) 18
D BLACK GROUND 18
EGREEN RIGHT ANGLE 18
F BLUE LEFT ANGLE 18
G BLUE/BLACK DRIVE. SLIDE BOX RET. 18
H BLUE/WHITE DRIVE. SLIDE BOX EXT. 18
J RED/BLACK PASS. SLIDE BOX RET. 18
K RED/WHITE PASS. SLIDE BOX EXT. 18
END VIEW
LOOKING AT CONNECTOR
A
B
E
DC
K
JHG
F
PLASTIC ELECTRIC CONNECTOR -
FEMALE (P/N 62046)
SILICONE RUBBER CABLE SEAL (18 AWG) - P/N 62096
FEMALE TERMINAL (18-16 AWG) - P/N 62093
C2 CONNECTS TO C1 ON PAGE 20.
M1 CONNECTS TO M2 ON PAGE 24.
END VIEW
LOOKING AT CONNECTOR
4 3 1
9 8
10
14 13
2
7
12 11
6 5
BLIZZARD PLUG (SQUARE)
PIN COLOR FUNCTION AWG
NO.
BLACK GROUND 18
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
3GREEN RIGHT ANGLE 18
4 BLUE LEFT ANGLE 18
5 N/A N/A N/A
6 N/A N/A N/A
7 N/A N/A N/A
8 RED/BLACK PASS. SIDE SLIDE BOX RET. 18
9 BLUE/BLACK DRIVE. SIDE SLIDE BOX RET. 18
10 BROWN PUMP SOLENOID 18
11 N/A N/A N/A
12 N/A N/A N/A
13 RED/WHITE PASS. SIDE SLIDE BOX EXT. 18
14 BLUE/WHITE DRIVE. SIDE SLIDE BOX EXT. 18
1
2
JACKET MATERIAL
BLACK NYLON BRAID
240"
60"
BLACK (NEGATIVE)
PINK/BLACK (POSITIVE)
#10 RING TERMINALS
(22-18 AWG) - P/N 62100
2"1"
HEAT AND CAP
BRAIDING END
1/2" REVERSE
BRAIDING
MOLDED RUBBER WEATHER CAP - FEMALE
(P/N 62133)
Wire Harness Extention (Vehicle) Wire Schematic 23
810SS WIRE HARNESS EXTENSION ( VEHICLE) WIRE SCHEMATIC (2003)
BROWN
C2 M1
BLUE/BLACK
BLUE/WHITE
GREEN
RED/BLACK
BLUE
RED/WHITE
BLACK
BLACK
PINK/BLACK
24 Diagram - Wire Harness Extension (Plow)
810SS WIRE HARNESS EXTENSION
PLOW SIDE (2003)
P/N 62134
NOT DRAWN TO SCALE
UNLESS OTHERWISE SPECIFIED
PLASTIC ELECTRIC CONNECTOR -
FEMALE (P/N 62046)
SILICONE RUBBER CABLE SEAL (18 AWG) - P/N 62096
FEMALE TERMINAL (18-16 AWG) - P/N 62093
PACKARD GT 280 ELECTRIC CONNECTOR
PIN COLOR FUNCTION AWG
NO.
A N/A N/A N/A
BBROWN PUMP SOLENOID 18
C N/A N/A N/A
DBLACK GROUND 18
EGREEN RIGHT ANGLE 18
FBLUE LEFT ANGLE 18
GBLUE/BLACK DRIVE. SLIDE BOX RET. 18
HBLUE/WHITE DRIVE. SLIDE BOX EXT. 18
J RED/BLACK PASS. SLIDE BOX RET. 18
K RED/WHITE PASS. SLIDE BOX EXT. 18
END VIEW
LOOKING AT CONNECTOR
A
B
E
DC
K
JHG
F
MOLDED RUBBER CONNECTOR
M2 CONNECTS TO M1 ON PAGE 22.
C3 CONNECTS TO C4 ON PAGE 26.
BLIZZARD PLUG (SQUARE)
PIN COLOR FUNCTION AWG
NO.
BLACK GROUND 18
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
3 GREEN RIGHT ANGLE 18
4 BLUE LEFT ANGLE 18
5 N/A N/A N/A
6 N/A N/A N/A
7 N/A N/A N/A
8 RED/BLACK PASS. SIDE SLIDE BOX RET. 18
9 BLUE/BLACK DRIVE. SIDE SLIDE BOX RET. 18
10 BROWN PUMP SOLENOID 18
11 N/A N/A N/A
12 N/A N/A N/A
13 RED/WHITE PASS. SIDE SLIDE BOX EXT. 18
14 BLUE/WHITE DRIVE. SIDE SLIDE BOX EXT. 18
1
2
JACKET MATERIAL
BLACK NYLON BRAID
66"
HEAT AND CAP
BRAIDING END
HEAT AND CAP
BRAIDING END
12"
36"
BLACK 3/8" END RING TERMINAL
P/N 62072
7
1211
65
21 4
3
8 9
10 13 14
END VIEW
LOOKING AT CONNECTOR
MOLDED RUBBER WEATHER CAP - MALE
(P/N 62135)
Wire Harness Extension (Plow) Wire Schematic 25
810SS WIRE HARNESS EXTENSION (PLOW) WIRE SCHEMATIC (2003)
BROWN
M2 C3
BLUE/BLACK
BLUE/WHITE
GREEN
RED/BLACK
BLUE
RED/WHITE
BLACK
BLACK
26 Diagram - Coil Wire Harness
810SS COIL WIRE HARNESS (2003)
P/N 62161
NOT DRAWN TO SCALE
UNLESS OTHERWISE SPECIFIED
ALL DIMENSIONS IN INCHES
A
BC
E
D
FGH
K
J
END VIEW
LOOKING AT CONNECTOR
PACKARD GT 280 ELECTRIC CONNECTOR
PIN COLOR FUNCTION AWG
NO.
A N/A N/A N/A
BBROWN PUMP SOLENOID 18
C N/A N/A N/A
D N/A N/A N/A
E GREEN RIGHT ANGLE 18
F BLUE LEFT ANGLE 18
G BLUE/BLACK DRIVE. SLIDE BOX RET. 18
H BLUE/WHITE DRIVE. SLIDE BOX EXT. 18
J RED/BLACK PASS. SLIDE BOX RET. 18
K RED/WHITE PASS. SLIDE BOX EXT. 18
C4 CONNECTS TO C3 ON PAGE 24.
PLASTIC ELECTRIC CONNECTOR - MALE (P/N 62045)
SILICONE RUBBER CABLE SEAL (18 AWG) - P/N 62096
MALE TERMINAL (18-16 AWG) - P/N 62097
COILS-12VDC
PDL-P/N 62163
LDL-P/N 62164
BLUE/BLACK
GROUND
BLUE/WHITE
GROUND
RED/WHITE
GROUND
S9
DRIVER’S SIDE
SLIDE BOX RETRACT
S10
DRIVER’S SIDE
SLIDE BOX EXTEND
GREEN
GROUND
S4
RIGHT ANGLE
RED/BLACK
GROUND
S1
PASSENGER’S SIDE
SLIDE BOX RETRACT
S2
PASSENGER’S SIDE
SLIDE BOX EXTEND
STAMPING ON
MANIFOLD
3/8" END RING TERMINAL
P/N 62118
BROWN
GROUND
S5
PUMP SOLENOID
BLUE
GROUND
S3
LEFT ANGLE
8"
15"
Coil Wire Harness Wire Schematic 27
810SS COIL HARNESS WIRE SCHEMATIC (2003)
BROWN
C4
BLUE/BLACK
BLUE/WHITE
BLUE
GREEN
RED/BLACK
RED/WHITE
BLACK
DRIVE. SIDE RETRACT
GROUND
DRIVE. SIDE EXTEND
GROUND
PASS. SIDE EXTEND
GROUND
S9
S10
RIGHT ANGLE
GROUND
S4
S2
PUMP SOLENOID
GROUND
S5
LEFT ANGLE
GROUND
S3
PASS. SIDE RETRACT
GROUND
S1
28 Diagram - Auxiliary Control Harness
810SS AUXILIARY CONTROL HARNESS (2003)
WITH INTERNAL DIODES
P/N 62162
NOT DRAWN TO SCALE
UNLESS OTHERWISE SPECIFIED
ALL DIMENSIONS IN INCHES
PLASTIC ELECTRIC CONNECTOR -
FEMALE (P/N 62046)
SILICONE RUBBER CABLE SEAL (18 AWG) - P/N 62096
FEMALE TERMINAL (18-16 AWG) - P/N 62093
PACKARD GT 280 ELECTRIC CONNECTOR
PIN COLOR FUNCTION AWG
NO.
A N/A N/A N/A
BBROWN PUMP SOLENOID 18
C N/A N/A N/A
D BLACK GROUND 18
E GREEN RIGHT ANGLE 18
F BLUE LEFT ANGLE 18
G BLUE/BLACK DRIVE. SLIDE BOX RET. 18
H BLUE/WHITE DRIVE. SLIDE BOX EXT. 18
J RED/BLACK PASS. SLIDE BOX RET. 18
K RED/WHITE PASS. SLIDE BOX EXT. 18
END VIEW
LOOKING AT CONNECTOR
A
B
E
DC
K
JHG
F
C3 CONNECTS TO C4 ON PAGE 28.
M2 CONNECTS TO SKID STEER CONNECTOR
JACKET MATERIAL
BLACK NYLON BRAID
66"
HEAT AND CAP
BRAIDING END
BLACK
GREEN
BLUE
RED/BLACK
BLUE/BLACK
RED/WHITE
BLUE/WHITE
4"
LOOM BRAID
(1/2 LOOM UNDER BRAID)
BLACK 36"
3/8" END RING TERMINAL
P/N 62072
2" 12"
BLACK WIRE SPLICE
1"
1/2" REVERSE BRAIDING
LOCATION OF
DIODE (X6) CLUSTER
8"
GREEN
SP–2 D1 BROWN
GREEN PIN–E
PIN–B
SP–1
BLUE
SP–3 D2 BROWN
BLUE PIN–F
PIN–B
SP–1
BLUE/BLACK
SP–4 D3 BROWN
BLUE/BLACK PIN–G
PIN–B
SP–1
BLUE/WHITE
SP–5 D4 BROWN
BLUE/WHITE PIN–H
PIN–B
SP–1
RED/BLACK
SP–6 D5 BROWN
RED/BLACK PIN–J
PIN–B
SP–1
RED/WHITE
SP–7 D6 BROWN
RED/WHITE PIN–K
PIN–B
SP–1
Auxiliary Control Harness Wire Schematic 29
810SS AUXILIARY CONTROL HARNESS WIRE SCHEMATIC (2003)
GREEN
BLUE
BLUE/BLACK
BLUE/WHITE
RED/BLACK
RED/WHITE
BLACK
GREEN - PIN E
BLUE - PIN F
BLUE/BLACK - PIN G
BLUE/WHITE - PIN H
RED/BLACK - PIN J
RED/WHITE - PIN K
BLACK - PIN D
BROWN - PIN B
M2 C3
D1
D2
D3
D4
D5
D6
SP-1
SP-2
SP-3
SP-4
SP-5
SP-6
SP-7
SP-8
30 Troubleshooting Guide (1 of 2)
Problem Probable Cause(s) Suggested Remedy
Plow functions will not work after all connect- S5 coil is not magnetizing. S5 coil should magnetize with each function.
ions are made or plow functions are slow.
Solenoid cartridge valve may be contaminated or damaged. Determine a damaged cartridge valve by reversing the
A bent or over torqued cartridge will not allow the valve to driver’s side and passenger’s side cartridge valves one
move freely inside of the cartridge. at a time. Replace valve if necessary.
Plow functions start and terminate suddenly. Skid steer hydraulic fluid flow is set to variable flow. For plow functions to work, the skid steer hydraulic fluid
flow should be set to continuous flow. Review your skid
steer operation manual for proper flow settings.
Multiple valves function simultaneously. Diodes may be corroded or damaged. Clean diodes thoroughly and/or replace.
Wire harness may be damaged. Verify harness is not damaged. Review wire schematic(s)
to troubleshoot connection(s). Replace if needed.
Plow functions are reversed. (i.e. Driver’s side Hydraulic hoses are connected wrong or coils and wiring Review the Hydraulic Valve & Hose Port Identification
wing extends when passenger’s side wing is are incorrect. Guide under the A-frame cover for proper port locations
activated from the control.) and/or place respective coils over correct valves.
Both wings extend when the skid steer Pressure (P) and tank (T) hoses are installed in the wrong Review the skid steer operation manual to determine the
hydraulics are turned on. position on the skid steer. pressure and tank connections.
Plow angles only one way. Skid steer computer conflicts with cylindrical connection. Using a jumper wire, connect pin K to pin L at the back
of the cylindrical connector (cylindrical connector only).
Wing will not stay angled when plowing. The wing pressure relief valve is contaminated. Test the wing pressure relief. Attach a T-fitting with a fluid
PSI gauge to the base end of the wing cylinder. Pressure
relief should not be greater than 1700 PSI. Replace if
less than 1500-1700 PSI.
Plow will not stay angled when plowing. The angle pressure relief valve is set too low. NOTE: Follow the guidelines indicated above; however, the PSI
Increasing the pressure relief valve will cause damage setting should not exceed 3000 PSI. NOTE: If the plow
to your plow. Do not set the pressure relief greater than is floating back when angled to the right, adjust the left
3000 PSI. pressure relief valve and vice versa.
Wing will not move. Control station, wire harness or cables may be loose or Verify control station, wire harness and all cables are
improperly connected. securely connected. Clean if necessary.
No power to the cartridge valve. Verify S9 & S10 coils (passenger’s side slide box retract
and extend) and S1 & S2 (driver’s side slide box retract
and extend) are connected properly. Diagnose the wire
harness. Review all wire harness schematics. If power is
present, review the next step.
Coils are receiving power. Verify that the coils are magnetizing. Position a screw-
driver inside of the coil. When the respective function is
activated, the screwdriver is drawn to the side of the coil.
If the coil is not drawn to the screwdriver, replace the coil.
If magnetization is present, review the next step.
Troubleshooting Guide
Prior to diagnosing your Power Plow, verify that all connectors (rubber connectors, plastic electric connectors,
ground and power wire terminals, coil wire and extension harnesses) are free of corrosion and are well lubricated
with white lithium grease. Insuring that all connectors are in good working order will save time in determining your
snowplow attachment’s service needs.
Troubleshooting Guide (2 of 2) 31
Problem Probable Cause(s) Suggested Remedy
Wing will not move (continued). Cartridge valve may be contaminated or damaged. A bent Determine a damaged cartridge valve by reversing the
or over torqued cartridge will not allow the valve to move driver’s side and passenger’s side cartridge valves one
freely inside of the cartridge. at a time. Replace valve if necessary.
Plow will not angle. Review all probable causes above. NOTE: Verify coils S3 & S4 for angle functions.
S10 S3 S4 S2
RV1 RV4
S9
RV2 RV3
RV5
S1
S5
Wing Pressure Relief Valves
Angle Pressure Relief Valve
Should your snowplow develop other problems not indicated in the Troubleshooting Guide, contact your local Dealer for technical assistance and/or replacement parts.
BLIZZARD
POWER PLOW
®
LIMITED CONSUMER WARRANTY
This warranty covers defects in material and workmanship except as set forth below.
WARRANTED PARTY:
This warranty applies only to the “Original Purchaser” who purchased this plow from an Authorized Blizzard Dealer,
for personal, family or household use.
TERM OF WARRANTY:
This Blizzard Power Plow snowplow is warranted for the following period:
Parts and labor are warranted for one year from date of purchase.
BLIZZARD CORPORATION’S WARRANTY REMEDY:
Blizzard Corporation will, at its sole discretion, repair or replace defective parts at no charge.
CUSTOMERS RESPONSIBILITY:
To obtain warranty service, the purchaser must return the defective snowplow to any Authorized Blizzard Dealer.
The purchaser must verify the original purchase date. Transportation costs to and from the dealer will be the
responsibility of the purchaser.
ITEMS NOT COVERED UNDER THIS WARRANTY:
This limited warranty does not cover the following:
1. Expendable parts such as cutting edges, plow shoes, hoses, fasteners, blade guides, paint finish, etc.
2. Any snowplow or part thereof which has been repaired or altered by anyone other than an Authorized Blizzard Dealer.
3. Any snowplow or part thereof which has been subject to neglect, misuse, accident, improper installation, maintenance,
or storage. This includes, but is not limited to, corrosion of any electrical components.
4. Snowplows mounted on skid steers other than those for whom Blizzard Corporation has provided a specific
mount system.
5. Blizzard Corporation does not assume liability for damage to the purchaser's skid steer resulting from the attachment
and use of a Blizzard Power Plow snowplow. Vehicle risk is the sole responsibility of the purchaser.
WARRANTY LIMITATIONS:
THIS WARRANTY IS OFFERED IN LIEU OF ANY OTHER EXPRESS WARRANTY.
THE DURATION OF ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
TO THE DURATION OF THIS WARRANTY.
BLIZZARD CORPORATION'S LIABILITY IS EXPRESSLY LIMITED TO REPAIR OR REPLACEMENT OF
DEFECTIVE PARTS. BLIZZARD CORPORATION SHALL NOT BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL
OR CONTINGENT DAMAGES WHATSOEVER, EVEN IF DAMAGES ARE CAUSED BY THE NEGLIGENCE OR
FAULT OF BLIZZARD CORPORATION.
State Laws: Some states do not allow exclusion of incidental or consequential damages or the limitations on how
long an implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you
specific legal rights and you may also have other rights which vary from state to state.
This warranty does not apply if you purchased your snowplow for other than personal, family, or household use. If
purchased for other than personal, family or household use, refer to the Blizzard Power Plow Commercial Warranty.
95 AIRPARK BOULEVARD CALUMET, MICHIGAN 49913 [906] 482-5555
1029-7-99 REV 8/01
COMMERCIAL WARRANTY
This warranty covers defects in material and workmanship except as set forth below.
WARRANTED PARTY:
This warranty applies only to the “Original Purchaser” who purchased this plow from an Authorized Blizzard Dealer,
for commercial use.
TERM OF WARRANTY:
This Blizzard Power Plow snowplow is warranted for the following period:
Parts and labor are warranted for one year from date of purchase.
BLIZZARD CORPORATION’S WARRANTY REMEDY:
Blizzard Corporation will, at its sole discretion, repair or replace defective parts at no charge.
CUSTOMERS RESPONSIBILITY:
To obtain warranty service, the purchaser must return the defective snowplow to any Authorized Blizzard Dealer within the
warranty period. The purchaser must verify the original purchase date. Transportation costs to and from the Dealer will be
the responsibility of the purchaser.
ITEMS NOT COVERED UNDER THIS WARRANTY:
This warranty does not cover the following:
1. Expendable parts such as cutting edges, plow shoes, hoses, fasteners, blade guides, paint finish, etc.
2. Any snowplow or part thereof which has been repaired or altered by anyone other than an Authorized Blizzard Dealer.
3. Any snowplow or part thereof which has been subject to neglect, misuse, accident, improper installation, maintenance,
or storage. This includes, but is not limited to, corrosion of any electrical components.
4. Snowplows mounted on skid steers other than those for whom Blizzard Corporation has provided a specific
mount system.
5. Blizzard Corporation does not assume liability for damage to the purchaser's skid steer resulting from the attachment
and use of a Blizzard Power Plow snowplow. Vehicle risk is the sole responsibility of the purchaser.
LIMITS OF BLIZZARD CORPORATION’S LIABILITIES:
BLIZZARD CORPORATION'S LIABILITY IS EXPRESSLY LIMITED TO REPAIR OR REPLACEMENT OF
DEFECTIVE PARTS. BLIZZARD CORPORATION SHALL NOT BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL
OR CONTINGENT DAMAGES WHATSOEVER, EVEN IF DAMAGES ARE CAUSED BY THE NEGLIGENCE OR
FAULT OF BLIZZARD CORPORATION.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED
WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
This warranty does not apply if you purchased your snowplow for personal, family, or household use.
In this case, refer to the Blizzard Power Plow Limited Consumer Warranty.
BLIZZARD
POWER PLOW
®
95 AIRPARK BOULEVARD CALUMET, MICHIGAN 49913 [906] 482-5555
1030-7-99 REV 8/01
95 Airpark Boulevard
Calumet, MI 49913
[888] 680-8600
[906] 482-5555
[906] 482-5445 Fax
www.blizzardplows.com
Blizzard, Power Plow, Blizzard Power Plow, WidePass and BucketBlade are trade-
marks of Blizzard Corporation. Blizzard is registered in the United States Patent
and Trademark Office. The Blizzard Power Plow snowplow is protected by U.S.
Patents 5,638,618; 5,899,007; 6,178,669; 6,276,076 and 6,393,737. Other patents
pending. Copyright © 2003 Blizzard Corporation. All rights reserved. 1306-06-03

Navigation menu