Bluecard Software Technology BLUECARD900 UHF Long Range Reader User Manual

Bluecard software Technology Co.Ltd. UHF Long Range Reader

User manual

            UHF Long Range Reader User Manual 902-928MHz          Model: BU-900R-K                          American Standard                                                                                      Please read this manual carefully, before starting to operate the reader.        ENGLISH
  2Table of Contents 1. INTRODUCTION....................................................................................................................3 1.1. Introduction ...............................................................................................................3 1.2. Audience.....................................................................................................................3 1.3. Reading Guide ..........................................................................................................3 1.4. Reader Description..................................................................................................3 2. CONTROL PANEL.................................................................................................................4 2.1. Power Supply ............................................................................................................4 2.2. Indicator......................................................................................................................4 2.3. Communications ......................................................................................................4 2.3.1. General Input / Output.........................................................................................4 2.3.2. Ethernet Data Transfer........................................................................................4 Communicate between reader to software via Ethernet RJ45 cable (it is based on TCP/IP protocols)...........................................................................................................4 2.4. Adjust Reading Ranges..........................................................................................5 2.5. Switch Board.............................................................................................................5 2.5.1. Trigger Reading ....................................................................................................5 2.5.2. Command Mode....................................................................................................6 2.5.3. Turn On/Off 2.4G...................................................................................................6 3. READING INSTALLTAION...................................................................................................6 4. CHOOSING & INSTALLING TAGS ....................................................................................7 4.1. Tag Model...................................................................................................................7 4.2. Reader & EPC Card Alignment.............................................................................8 5. TROUBLSHOTTING AND MAINTENANCE .....................................................................8 5.1. Troubleshooting .......................................................................................................8 5.2. Maintenance ..............................................................................................................8 6. TECHNICAL SPECIFICATIONS .........................................................................................9
  3 1. INTRODUCTION 1.1. Introduction BU-900R-K UHF Long Range RFID product is one of the significant RFID products designed by BlueCard. It is a reader compliant with EPC Gen2 standard, which is widely used in the fields such as Vehicle Parking Management System, Time & Attendance System, Personnel Access Control Management, and Stock Management System.   Advantages: -  Reading distance is up to 10 meters with passive card.. - Integrated antenna -  Wiegand output specialized for Access Control Management System. -  GOIP for external device control    1.2. Audience This document is used only by authorized BU-900R-K distributors, installation engineers. This manual provides you the instructions of testing, setting, installing of BU-900R-K, please read the manual carefully before start to use the reader.    1.3. Reading Guide This document is a detail instruction on BU-900R-K, which includes hardware description, tag instructions, power supply, host computer instruction, how to test and install the reader, troubleshooting, reader’s specifications and definition for the pins.  1.4. Reader Description Bluecard BU-900R-K UHF reader is long reading distance UHF RFID reader with attached antenna. BU-900R-K has five LED light to indicate the reader status. Please refer to the following figure for the BU-900R-K detail appearance.                   Front View               Side View             Back View LED Stud, Gasket, and Nuts for Mounting Removable Cover
  4     2. CONTROL PANEL          2.1. Power Supply BU-900R-K needs a dedicated power supply at the site in all the time. The acceptable power supply is 12V DC. Please use the AC-DV adapter supplied by the manufacturer.   INPUT OUTPUT Voltage/V  Power/Hz  Voltage/V  Ampere/A 100~240 47~63  12  5  2.2. Indicator Indicator  Definitions INPUT  Under trigger mode, the LED is flashing when reader receive signal from extra devices.COMM  The LED is flashing when communicate with host computer PWR  The LED is constant on when switch power on  2.3. Communications 2.3.1.  General Input / Output   The function allows you to receive extra devices’ signal, such as loop detector and optical sensors (for more details please refer to page 6 Trigger Reading). INPUT  when the external device sends 5~48V will trigger the reader make readings OUTPUT  can only driver the device less than AC110V / DC60V, less than 1A 2.3.2.  Ethernet Data Transfer Communicate between reader to software via Ethernet RJ45 cable (it is based on TCP/IP protocols). Color  Definition BLUE  Flash once: the power has been turned on  Flash & Beep once for each reading  Four Blue LED stays on means the environment is very bad situations RED   Constant On: reader standby with power supply Other Reserved Conection Ports
  5 2.4.  Adjust Reading Ranges This function is for active tag only. A standard BU-900R-K reader can work with both ECOMPUTER G2 C1 passive tags and active tags. With a passive tag, its reading range can be up to 10m, depending on tags and/or change the output power of the antenna. Its reading distances are more flexible on active tags. As there are more tag models selectable.    Each of our major active tag models has several sub-models, shown by suffix e.g. -12, -40 and -70.    These sub-models enable a reader to have variable minimum and maximum adjustable ranges. For example, to present both BGC-S-12 and BGC-S-70 tags in front of a BU-900R-K, the min. adjustable range for BGC-S-12, should be around 3-5m, while the min. adjustable range for BGC-S-40 can reach 20-30m. The maximum adjustable range on a -12 tag can be 12m, while on a -40 tag, it can make 40m and more.    On the same tag, clients can still set different reading ranges by rotating the embedded potentiometer in the reader.     Clients can use a small screwdriver to rotate the potentiometer clockwise or counter clockwise, accordingly the reading range becomes longer or shorter. At the adjustable extreme, you can hear a low spring-like sound, after that, further rotation in the same direction would not change the reading range any more. There are around five valid rounds between the minimum and maximum adjustable position.  2.5. Switch Board BU-900R-K can work on three reading modes. By factory default, when a BU-900R-K is connected to the appropriate power supply, it will begin to read tags continuously.    Also the reader can be triggered to read by a loop detector or infrared detector.       Users can switch between constant and trigger mode easily on the reader’s panel.   Notes: after switching the reading mode, the reader should restart to make the change takes effect.    2.5.1. Trigger Reading To enable this mode, the reader needs to be wired to a trigger (typically a loop detector or infrared detector) via its general input. For testing purposes, you may short IN+ with IN-, which will generate a valid trigger signal. Notes: when trigger signals received, BU-900R-K will continue to make reading for 2 seconds.
  6Users can pull out the terminal block on the reader’s interfaces for easy wiring with external devices, and then put it back to complete connection with the reader (shown below).                      2.5.2. Command Mode  In this mode, BU-900R-K will remain on standby until it receives a command from COMPUTER. For example, the reader will start to make readings when the COMPUTER sent a read command to a BU-900R-K, meanwhile, the reader will return a confirm data to computer as confirmation. The command mode is to facilitate clients to integrate the reader.    When a reader is working, it should emit LED and audio signals according to its operation status. Turn On/Off  Notes: after the switch, please restart the reader.   3. READING INSTALLTAION A BU-900R-K can be fixed in sites in any way they see fit. Installers are recommended to order a standard pole mounted bracket from the manufacturer to install the reader.   Below is our mounted bracket.                       The reader can be mounted on either a pole or wall. The reader is equipped with a linear horizontal antenna with limited readable angle. It should be installed at a suitable height and angle towards the ground, so as to give the optimal performance.    Reader Operation Status  LED Signals  Audio Signals Standby  Red Light Constant On  No Reading  Blue Light Keeps Flash  Beep Once for Each Read Pull out terminal blocks
  7A series of factors can affect the reader installation height and angles, including the reading distance, width of the lane, types of vehicles, etc. The figure below shows a typical installation for your reference.       4.  CHOOSING & INSTALLING TAGS 4.1. Tag Model Passive Card (EPC Standard)    BMC-G2C-01            BMC-G2C-04 Active Tags    BGC-S             BGC-04           BGC-K
  8 4.2.  Reader & EPC Card Alignment The following criteria must be satisfied to achieve the optimum read reliability:  Polarization of the tag and BU-900R-K must be aligned in the same direction.  The installed tag must be in a direct, unobstructed line of sight to BU-900R-K. All the materials reduce the RF signal. Metal and water can cause the significant problem by reflect and absorb single.  Polarization            correct tag position                        incorrect tag position  5. TROUBLSHOTTING AND MAINTENANCE 5.1. Troubleshooting  Q: Why the blue LED on my reader never flash and the reader cannot read tags? A: Please check with its reading mode settings. Only at the constant mode, the reader will read tags automatically. At the trigger mode, however, the reader should receive a triggering signal to start reading.    Q: My reader can hardly read a tag or the distance shorter than expected, what is the reason? A: The reader is equipped with a linear horizontal polarization antenna. So tags should be placed in a way where its polarization direction is in line with that of the reader’s antenna. If you consider the reading ranges not so well on a tag, please rotate the tag by 90º and try again.   Also in one of following situations, the reading distance can be shortened even there is no problem on the reader: tags are close to or have direct contact with human body, metal screen, or liquid obstruct between reader and tags.  Q: Why the reading distance of my reader on windshield tags is so short in the open air? A: Windshield tags, as the name suggested, should be attached on window so as to get optimal reading effects. For simulation, you can fix a tag on a piece of glass with crystal tapes, and try again with the reader.  5.2. Maintenance  There are a few tips to get the optimal performance out of the reader.
  91.  Always use the power adaptor provided by the manufacturer, or consult the supplier for a compliant power adaptor from a third source. 2.  DO NOT disassemble the reader. If there is any problem on the device, please return the supplier for repairing.    6.  TECHNICAL SPECIFICATIONS Reader Specifications Power Supply  12V/ DC,5A (current) Communication Interface  Wiegand (26/34); RS232 Serial Port Maximum Data Rate  4800bps, 9600bps, 57600bps, 115200bps Wiegand Data Rate  Pulse width time is 100us, pulse intervals time is 1.0ms GPIO  1 photo coupler input and output Dimension  460×260×110mm Weight 3 Kg Operating Temperature  -20 ºC ~+65 ºC Storage Temperature  -40 ºC ~+85 ºC Humidity 10-95% Environmental Sealing  IP65, DC ground lightening proof Housing  FRP + stain resistant aluminum  RFID Specifications Frequency Range  902-928MHz   Operating Mode  FHSS or Fixed Frequency Reading Range  Passive tag: up to 10m   Active Tag: depending on tags & adjustment Operation Mode  Constant, trigger, command Moving Tag Detection  ≤40Km/h Number of Antenna  1 integrated, linear horizontal
  10 FCC Statement: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.    This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:   (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including    interference that may cause undesired operation.          Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.  RF Exposure Statements: To comply with RF exposure requirements, antennas that are operating near users at stand-alone desktop of similar configurations must operate with a minimum separation distance of 20cm from all persons.          RFID devices for use through the EEA have the following restrictions: • Maximum radiated transmit power of 2W ERP.  Statement of Compliance: Bluecard software Technology Co., Ltd. hereby, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Navigation menu