Bosch Security Systems B119 Belt Pack Transmitter User Manual

Bosch Security Systems, Inc. Belt Pack Transmitter Preliminary Users Manual

a href="https://usermanual.wiki/Bosch-Security-Systems" itemprop="url"> Bosch Security Systems >

User Manual

Preliminary Users Manual Electro-Voice Model REV-WT Wireless Microphone Transmitter The Electro-Voice (Ev) REV-WT is a Professional Grade Wireless Beltpack Transmitter operating in the UHF frequency range. The REV-WT combines frequency agility and ease of use like no other. The transmitter operates within a 24 MHz wide segment in 25 KHz steps. The high quality audio circuitry and advanced Radio Frequency (RF) signal processing offer broadcast quality signal-to-noise ratio and audio clarity. The RF range of the REV-WT communicating to a receiver may be up to 150 meters (492 ft). System features include: • Durable Painted Metal Case. • TA-4F Audio Connector. • Permanent Flash Memory for frequency/setting storage. • On-Loc prevents accidental power off (when set). • LCD Display for ease of viewing. • Flexible quarter wave screw-on Antenna. Quick set-up: 1. With the Power Switch on the transmitter OFF, install fresh batteries into the transmitter. 2. To prevent feedback or unintentional noise, mute the audio mixer/amplifier or other device during set-up adjustments. Place the transmitter Power Switch to the ON position. 3. The Battery light near the Off/On switch will flash once and then go off. If the light does not flash, a bad battery is the most likely cause. The display will also come on briefly displaying the current frequency group and channel and the battery level. Note: Anytime Power is removed and turned back on, the GP/CH/Bat screen will be displayed.
REV-WT Users Manual Page 2 Quick set cont’d. 4. If the Group and Channel match the desired receiver group and channel, proceed to Step 9. If not, proceed to Step 5. 5. To select a different GP/CH, press SET one time. The Group will start flashing. Use the up and down arrows to change the group number. Press the SET button to save the Group. After setting the Group, The Channel number will start flashing. Use the up/down arrows to change the Channel number. Press SET and the channel is now saved. 6. There are 18 preferred Groups and up to 16 Channels available in stored memory. If desired, you can create new groups/ channels but you must change to a new frequency to store in that group/channel. In order to select a new frequency, you must have a “users” group /channel selected. Press the SET button. The Group should be flashing. Press the Up arrow until group 19u is found (any u group can be used) Press SET. The Channel should now be flashing. Select a channel with the up/down arrow. Press SET. You are now ready to select a frequency to store in the users group above. Press the Menu button one time. A “dashed” line may appear on the display (if this is the first user program) or a previously stored frequency will be displayed. Press the Set button one time. The line or frequency should start flashing. Press the Set button one time then use the Up/Down arrow buttons to select the desired frequency. Press Set when complete. The selected frequency should be displayed and not be flashing.
Download:
Mirror Download [FCC.gov]
Document ID1005817
Application IDHJsOkcdwtUgG1iiG2tyJHw==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize3.01kB (37650 bits)
Date Submitted2008-09-24 00:00:00
Date Available2008-09-24 00:00:00
Creation Date2008-08-29 09:45:54
Producing SoftwareAcrobat Distiller 7.0.5 (Windows)
Document Lastmod2008-08-29 09:46:36
Document TitlePreliminary Users Manual
Document CreatorAcrobat PDFMaker 7.0.7 for Word
Document Author: Connerc
FCC ID Filing: B5DB119

Navigation menu