Braun Corporation Fmvss No 403 Users Manual
403 to the manual 3062a17b-8e38-4db5-93d0-dca872d9d80e
2015-02-02
: Braun Braun-Corporation-Fmvss-No-403-403-Users-Manual-409694 braun-corporation-fmvss-no-403-403-users-manual-409694 braun pdf
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 31312 "RAUN #ORPORATION &-633 .O 1UICK 2EFERENCE )NSTALLATION 3HEET .(43! 6EHICLE 0HYSICAL 2EQUIREMENTS Lowered (Drop) Floor Requirements Nonmodified OEM full size van floors meet all requirements for Vangater II. Nonmodified OEM mini van floors meet all requirements for Mini Vangater II. Must meet or exceed nonmodified OEM floor section. e Fram e Tub Position wedge plate(s) to achieve a 1/2" preload at right inboard corner of platform. See Figures C and D. &IGURE $ Clearances ge ed te W la P OEM (Van) Chassis Floor Requirements Place lift in approximate position. Note: Hoist or other lifting device is recommended. ge ed t e W la P h$/4 0RIVATE 5SE ,IFTv 1 0OSITION ,IFT Minimum 1" clearance between lift and vehicle. See Figure E. Door Opening Dimensions Vehicle lift access door opening must meet specified dimensions. “1992” and Newer Ford Slide Door 1. Remove the lower slide door stop. 2. With Power Door: Door stop not used. Vehicle Door Opening Without Power Door: Drill (2) holes in the lower door stop at dimensions shown in Figure B. B 1/2" Position wedges as needed for 1/2" preload. &IGURE # Maximum 1/2" between inboard locator and floor when locator is deployed. See Figure E. Minimum 3/4" clearance between door and vertical arm. See Figures F and G. Floor Stepwell 3. Replace door stop, locating on the (2) drilled holes (provides adequate clearance). A Maximum 1/2" Inboard Locator &IGURE % Minimum 1" Clearance 1-7/16" 2-3/4" C &IGURE & &IGURE ! &IGURE ' Floor Floor Ground Level 31-1/2" 39-1/2" 29" 29" B Clear Door Opening C Maximum Floor-to- &IGURE " PARALLEL (ALIGNED) or 48" Wall (ALIGNED) (ALIGNED) Minimum 3/4" Clearance wing Do Full Size 42" PARALLEL D oo r Minivan Wall (ALIGNED) ng t Swi Fron A DimenMinimum Clear Wall Slide Door Rear S Drill (2) 5/16" diameter holes. Minimum 3/4" Clearance Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 31312 2 3ECURE ,IFT 5. Carefully operate lift through all functions checking for clearances (specified in Figures D-I). Adjust lift position and/or upper mounting hardware as needed. 6. Drill 3/8" diameter holes through floor using the corner holes in the base plate as a template. Refer to Figure H. Insert 3/8"-16 hex bolts and secure below floor as specified in Figure H (bolt lengths as required per application). Tighten all mounting hardware securely. All fasteners must meet FMVSS 571.403 Section 6.3. 8. Position and secure docking bumper. See Figure L. 9. Position and secure warning sensor mat as specified in Figure M. Connect wiring harness to lift as shown in Figure P. Fab-Lock Bolt 2. Insert Fab-Lock bolts (minimum 2) fully through mounting channel and C pillar. 5/16" Socket 4. Place a 5/16" socket onto the inner screw and tighten (turn clockwise). 5. Turn socket until Fab-Lock has expanded against metal surface. Ratchet Wrench Platform &IGURE , Trim 3/8" Body Washer Floor 3/8-16 x 2" Hex Bolt (Qty: 2) 3/8" Lock Washer Hardware Typical All Positions 3/8-16 Hex Nut Upper Adjustment Bracket Upper Adjustment Bracket 3/8-16 x 3" Hex Bolt 5/16-18 x 3/4" Flat Head Screw 5/16" Flat Washer 5/16" 5/16" Lock Hex Nut Washer Upper Mounting Channel 5/16" Flat Washer 3/8" Lock Washer 3/8-16 Hex Nut Stepwell Docking Bumper Fab-Lock Bolt 3/8" Lock Washer 3/8" Hex Nut Vertical Mounting Brace Upper Mounting Bracket 3/8-16 Slide Nut Vertical Mounting Brace 5/16" Flat Washer Note: Cut bracket off flush with mounting brace and install foam padded cover using cable ties. &IGURE ) Upper Mounting Channel e Fram e Tub 5/16" Flat Washer Hardware typical opposite side 5/16-18 x 7/8" Button Head Cap Screw 5/16" Lock Washer Threshold Warning 3/8-16 x 1" Hex Cap Screw with Lock Washer (Qty: 2) &IGURE - #10-16 x 1-1/2" Wafer Head Phillips Self-Drilling Screw (Qty: 4) &IGURE + . Min 18" Wall (C Pillar) Ed ge of F Upper Adjustment Bracket Vertical Mounting Brace 3/8-16 x 3" Hex Bolt with Lock Washer and Hex Nut d ol sh g re in Th arn W 7. Cut upper adjustment bracket off flush with mounting brace and install foam padded cover using cable ties. Note: Cover power unit before cutting bracket. Docking Bumper 1/4" Flat Washers Docking Bumper Vertical Mounting Brace 4. Secure upper adjustment bracket and upper mounting channel assembly to vertical mounting brace. 3. Place a 5/8" wrench onto bolt head and secure tightly or Flo Outer Pivot &IGURE * 5/8" Wrench 5/16" Flat Washer Position wedges as needed. ge ge ed te ed te W la W la P P Carefully drill 5/16" diameter wall mounting holes. Secure upper mounting channel to wall (C pillar) using expanding Fab-Lock bolts (minimum 2). See Figure J. 1. Remove rubber washer and install 1/4" flat washers. 3/8-16 Hex Bolt (Minimum 4) • One in each corner. • Lengths as required per application. e Fram e Tub 2. Secure vertical mounting brace and upper mounting bracket to frame tube. See Figure I. 3. Temporarily assemble upper adjustment bracket and upper mounting channel. See Figure K. Position assembly and mark mounting holes on van wall (C pillar). Fab-Lock Bolt Installation &IGURE ( 1. Temporarily secure base plate by installing sheet metal screws in base plate slots. ini sh ed Flo or Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 31312 W11 W20 1 2 3 1 2 3 1 2 1 1 2 2 D20 D24 D21 D7 D6 D5 D11 1 D30 J9 D31 1 1 D10 D29 D19 W13 R56 D18 C43 C45 K4 C39 K5 K1 C47 C42 D9 J8 4 3 D16 2 D15 1 C35 R60 D4 C30 R37 R38 C31 U8 R35 R36 R45 C34 U9 R50 U11 LIFT R66 R32 18 29 W14 R7 C11 D2 U6 C54 5 W2 40 C 10 7 1 J5 C12 W3 1 2 3 R2 C4 R34 R46 R25 U3 R11 R14 C26 R33 R31 R30 W5 1 2 3 J4 C7 R51 ON ON ON R71 + + D12 S1 1 2 3 D13 U10 R53 D14 C53 R58 R54 R55 R57 C38 D22 R59 D23 C29 100024-001 REVISION R28 6 5 " 1/ 8" Pl x 4" as x tic 4 W17 4 C6 C2 Threshold Sensor Stow Limit Floor Limit Down Limit Unfold Limit Fold Limit Barrier Limit Deploy Limit 1 Up Limit 2 GND C50 F1 J2 Door Limit 3 12V C51 + C3 + + + C52 + C5 12V GND D28 C40 CAUTION! ESD HAZARD L1 L2 U1 7 12V Q5 C46 ON R68 R15 BUZZER D32 R72 Q3 R67 C27 1 2 W4 1 2 3 C28 R6 R5 C9 C13 R8 R9 C8 R4 C15 R12 J6 COUNTER Q6 + + W1 1 2 3 U5 C1 R1 Q2 SPEED 1 2 3 HIGH ON ON MED-HI OFF ON MED-LO ON OFF LOW OFF OFF R18 R17 TRIFOLD ENABLE ON C17 C21 R22 R21 C20 C22 R19 R16 U7 C23 C19 R24 R23 R13 C25 R26 R27 R29 L3 U4 C16 C18 C14 R10 R64 R63 R39 D27 Q7 Y1 C24 R20 R3 6. Carefully connect opposite end of lead cable to Positive (+) post of battery. R73 R69 R40 R44 Q4 C32 R49 R52 D3 R65 + GY/R R47 R48 R42 R43 R41 Q1 BARRIER W12 K3 C36 D8 INTERLOCK C37 K2 C33 1 C41 1 2 3 4 5. Attach power cable to Auxiliary terminal of Circuit Sentry. Attach one end of 18" lead cable to the Battery Circuit Sentry terminal. W10 W9 D26 D17 1 4. Connect ground cable to vehicle framing member (see detail below). W8 W7 W6 Locate Circuit Sentry within 12" of positive (+) battery terminal. Mount Circuit Sentry with four self-tap screws. Sandwich 1/8" x 4" x 4" plastic between Circuit Sentry and mounting surface. 1 2. Insert grommet. Secure grommet with two self-tap screws. 3. Route ground and power cables through grommet. Route cables clear of exhaust, other hot areas and moving parts. WARNING Install and verify proper operation of all NHTSA mandated interlocks as specified. Failure to do so will result in a non-compliant installation and may result in serious bodily injury and/or property damage. Note: Detailed installation instructions are supplied with interlock kit(s). To meet minimum NHTSA requirements, connect vehicle interlock signal wires as detailed in Figure P (Steps 1-4): 2 1. Drill 1-1/8” diameter grommet access hole. Check under the vehicle for obstructions. Universal Interlock Kit 30940K is available for easy interface with vehicle OEM electronic signals. K6 R70 Y/LT. BU 1 M 2" ax . B at . Ne g. Ca bl e A ro un d W16 J1 9/32" Diameter Pilot Hole &IGURE 0 J3 D1 5/16" External Tooth Star Washer &IGURE / Ground Cable Mounting Lift mounted ground cable ground cable must be mounted to a vehicle framing member to provide optimum ground. Ground Cable Corrosion: When mounting ground cables, remove undercoating, dirt, rust, etc. from framing member around mounting holes (minimum 5/8” diameter area). Apply protective coating to mounting holes to prevent corrosion. Failure to do so will void warranty of certain electrical components. BN BK Connect vehicle 4 interlock signal wires. Cut 1 wire. Install butt 3 connector. W Thread Cutting Screw Disconnect and discard. Door Cut-Out Switch Harness BK Ground Cable GY 2 is ass Ch BK G Po s. Optional Interlock Kits A 2-circuit lift/vehicle interlock interface harness is provided inside the tower cover. The Grey/Red wire is connected to the battery power stud. A butt connector is provided on the Yellow/Light Blue wire. U12 L C a e ad bl e ab le Ci Se rcu nt it ry Po we rC ux . G ro m m et e Fram e Tub Vehicle and Lift Interlock + + &IGURE . 4 #ONNECT )NTERLOCK + + 3 !TTACH 0OWER AND 'ROUND #ABLE Threshold Warning Sensor Harness (Ve hic le (Li ft S to Y/L wed S T. BU igna l) GY Se /R cu re Sig na l) Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 31312 2%15)2%$ "9 &%$%2!, ,!7 6 5 ,IMIT 3WITCH !DJUSTMENT Floor Level Cam Adjustment: Stepwell Application &IGURE 1 The floor level cam(s) are located on the lower drive arm shaft, on the rear side of the frame tube (under the cover). Adjust per application. Audible Threshold Warning Screws DOT — Private Use Lift • Stepwell Application (Figure Q) 1. 2. 3. 4. &-633 #ERTIlCATION #HECKLIST -UST BE #OMPLETED AND 3IGNED Cam Position platform at floor level. Loosen the two cam screws. Adjust the cam for proper switch activation. Tighten the two cam screws. Switch The operations listed below must be functionally verified. This lift is not available for use unless these operations have been verified by the installerʼs signature below. Threshold Warning Sensor • Dropped Floor Application (Figure R) Switch Arm • Up-Stop Adjustment (inner cam and switch): 1. Position platform at original floor height (full up position). 2. Loosen screws A, B and C. 3. Adjust the inner cam for proper switch activation. 4. Tighten screw B. Dropped Floor Application &IGURE 2 A B Inboard Locator Outer Cam • Floor Level Adjustment (outer cam and switch): C 1. Position platform at lowered floor level. 2. Loosen screws A and C. 3. Adjust the outer cam until the floor level switch activates. 4. Tighten screws A and C. Verified: Deploy Limit Switch Deploy Limit Switch Adjustment (Figure S) 1. Position platform at floor level. 2. Loosen the screw that secures the cam to the vertical arm. 3. Level platform using a level (or as needed). 4. Adjust cam so the deploy limit switch activates. 5. Tighten screw. 6. Verify position and check level. Switch Inner Cam Activated when the platform switches from the up/down positions to the stow/deploy positions. This switch adjusts the angle of the platform when positioned at floor level. The platform should be level with the van floor. The switch is located on the vertical arm where the switch arm pivots. Platform &IGURE 3 Switch Arm Screw Vertical Arm Cam Deploy Limit Switch Outer Barrier Vehicle movement is prevented unless the platform is fully stowed. The outer barrier will not raise if occupied by at least 25 pounds. Lift operation shall be prevented unless the vehicle is stopped and vehicle movement is prevented. An audible warning will activate if at least 25 pounds is on the threshold area when the platform is at least one inch below floor level. The platform will not fold/stow when at least 50 pounds is on the platform. Raising the platform more than 3” off of the ground is prevented unless the outer barrier is raised. Lift Model: Series No: Serial No: Process, fold and insert completed document in the lift-mounted operatorʼs manual storage pouch. Verified By: Signature Required 2%15)2%$ "9 &%$%2!, ,!7 Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 31312 ,IFT /PERATING )NSTRUCTIONS WARNING Whenever a passenger is on the platform, the: • Passenger must face outward • Wheelchair brakes must be locked • Inboard locator and outer barrier must be UP. Failure to do so may result in serious bodily injury and/or property damage. A Before lift operation, park the vehicle on a level surface, away from vehicular traffic. Place the vehicle transmission in “Park” and engage the parking brake. Lift-posted Warnings and Lift Operating Instructions decal 31185 provides lift operating instructions. Replace any missing, worn or illegible decals. Photos appearing in the Lift Operating Instructions depict lift functions being activated by liftmounted control switches only. Follow the Manual Operating Instructions in event of power or equipment failure. Do not use electrical override to operate the lift when a passenger is on the platform. TO OPEN DOOR(S): B TO UNLOAD PASSENGER: G 1. Load passenger onto platform facing outward and lock wheelchair brakes. Note: Outer barrier must be UP before loading passenger onto platform. I Power Door Operator(s): Press the DEPLOY switch until door(s) are fully open. Release switch. LEVEL Switch 2. If necessary, press the switch arm LEVEL switch until platform is level. 3. Press DOWN switch until the entire platform reaches ground level and outer barrier unfolds fully. Release switch. See Photo K. Manual Door(s): Manually open door(s) fully and secure. C A TO DEPLOY PLATFORM: D K 2. Press DEPLOY switch until platform until platform stops (reaches floor level) and the inboard locator unfolds. See Photos C and F. Release switch. TO UNLOAD PASSENGER: DOWN Switch J L 4. Unlock wheelchair brakes and unload passenger from platform. 1. Press DEPLOY switch until platform sections open (rotate) to full width. See Photos D and E. Release switch. E H Note: Outer barrier must be fully unfolded until entire wheelchair has crossed the barrier. See Photos M and N. F M N Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 31312 ,IFT /PERATING )NSTRUCTIONS TO LOAD PASSENGER: Inboard Locator (unfolded) 1. Load passenger onto platform facing outward and lock wheelchair brakes. See Photos Q and R. Note: Outer barrier must be fully unfolded until entire wheelchair has crossed the barrier. See Photos O and P. O Q P 5. Unlock wheelchair brakes and unload passenger from platform. X W R TO STOW PLATFORM: 1. Press STOW switch until platform stops (fully stowed - vertical). Release switch. Y UP Switch 2. Press UP switch until platform raises just above ground level. Release switch. Z 2. Press STOW switch (Photo Y) until platform sections close (rotate) to locked position. See Photos AA-CC. LEVEL Switch 3. If necessary, press the switch arm LEVEL switch until platform is level. S T BB AA V U TO CLOSE DOOR(S): UP Switch Power Door Operator(s): Press the STOW switch until door(s) are fully closed. Release switch. 4. Press UP switch until platform stops (reaches floor level) and inboard locator unfolds (see Photo W). Release switch. Manual Door(s): Manually close door(s) fully. CC DD Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 31312 -ANUAL /PERATING )NSTRUCTIONS If you experience power or equipment failure, refer to the Manual Operating Instructions to operate the lift. Do not use electrical override to operate lift when a passenger is on the platform. WARNING Do not use electrical override to operate lift when a passenger is on the platform. Doing so may result in serious bodily injury and/or property damage. Refer to the Lift Operating Instructions for all normal lift operation procedures (such as loading and unloading passengers). Follow all Lift Operation Safety Precautions! PLATFORM LATCH INBOARD LOCATOR Locked Unlocked Hairpin The Electrical Override feature is provided as a diagnostic procedure to reset the system and as an alternative method of operating the lift without a Hand Crank Note: For easier operation of the hand crank, press and hold the electrical override MANUAL/BRAKE RELEASE switch in the MANUAL position while turning crank. ACTUATOR MOTOR Cap Plug Stow Inb o Lo ard cat or %LECTRICAL /VERRIDE )NSTRUCTIONS Deploy Down WARNING Up • Do not use electrical override to operate lift when a passenger is on the platform. • Override switches must be released to stop lift at desired position. Failure to follow these rules may result in serious bodily injury and/or property damage. passenger only. Do not use the electrical override to operate the lift when a passenger is on the platform. Lift functions operate at higher rate of speed when using the electrical override. When using the electrical override, the operator must stop pressing the applicable override switch when the lift reaches the desired position (limit switches will not function). Note: Following electrical override procedures, press the two override rocker switches to NORMAL. Close access cover and press the main control switch to STOW. Function lift through one full cycle to ensure proper operation. Locked Unlocked &IGURE ! Electrical Override Switches Link &IGURE ! TO OPEN DOOR(S): Manually open door(s) fully and secure. TO DEPLOY PLATFORM: 1. Unlock (disengage) latch under middle platform section. See Figure A. 2. Manually open (rotate) the three platform sections to full width. 3. Engage latch under middle platform section to lock platform sections at full width. See Figure A. 4. Remove cap from top of vertical arm actuator. See Figure C. 5. Place crank handle on actuator shaft and turn counterclockwise until platform reaches floor level. See Figure C. Remove crank handle. &IGURE " &IGURE # TO DEPLOY INBOARD LOCATOR: 1. Remove hairpin cotter from inboard locator link pin. See Figure B. 2. Remove link from inboard locator pin. See Figure B. 3. Lower (unfold) inboard locator to vehicle floor. TO STOW INBOARD LOCATOR: 1. Raise (fold) inboard locator to vertical position. 2. Place link on inboard locator pin. See Figure B. 3. Insert hairpin cotter into inboard locator link pin. See Figure B. TO LOWER PLATFORM: 1. Remove plug from top of motor cover. See Figure D. 2. Place crank handle on motor shaft and turn clockwise until platform reaches ground level. See Figure D. Remove crank handle. &IGURE $ TO RAISE PLATFORM: 1. Remove plug from top of motor cover. See Figure D. 2. Place crank handle on motor shaft and turn counterclockwise until platform reaches floor level. See Figure D. Remove crank handle. TO STOW PLATFORM: 1. Remove cap from top of vertical arm actuator. See Figure C. 2. Place crank handle on actuator shaft and turn clockwise until platform stops (reaches full vertical position). See Figure C. Remove crank handle. 3. Unlock (disengage) latch under middle platform section. See Figure A. 4. Manually close (rotate) the three platform sections 5. Engage latch under middle platform section to lock platform sections. See Figure A. TO CLOSE DOOR(S): Manually close door(s). TO OPEN DOOR(S): TO OPEN DOOR(S): Manually open door(s) fully and secure. Manually open door(s) fully and secure. TO DEPLOY PLATFORM: TO STOW PLATFORM: 1. Unlock (disengage) latch under middle platform section. See Figure A. 2. Manually open (rotate) the three platform sections to full width (unfolded). 3. Engage latch under middle platform section to lock platform sections at full width. See Figure A. 4. Rotate the access cover to expose the override switches. See above photo. 5. Press the two override rocker switches to OVERRIDE. 6. Press the left toggle switch to DEPLOY until platform reaches floor level. Release switch. 7. Press the right toggle switch to DOWN until platform reaches ground level. Release switch. 8. To deploy (unfold) the outer barrier, press the left toggle switch to DEPLOY until barrier unfolds fully. Release switch. 1. Rotate the access cover to expose the override switches. See above photo. 2. Press the two override rocker switches to OVERRIDE. 3. To raise (fold) the outer barrier to vertical position, press the left toggle switch to STOW until barrier folds fully. Release switch. 4. Press the right toggle switch to UP until platform reaches floor level. Release switch. 5. Press the left toggle switch to STOW until platform reaches vertical position. Release switch. 6. Unlock (disengage) latch under middle platform section. See Figure A. 7. Manually close (rotate) the three platform sections to closed position (folded). 8. Engage latch under middle platform section to lock platform sections. See Figure A. Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 31312 -AINTENANCE AND ,UBRICATION Proper maintenance is necessary to ensure safe, troublefree operation. Inspecting the lift for any wear, damage or other abnormal conditions should be a part of your daily routine. Simple inspections can detect potential problems. The maintenance and lubrication procedures specified in this schedule must be performed by a Braun authorized service representative at the scheduled intervals according to the number of cycles. The Vangater II is equipped with hardened pins and self-lubricating bushings to decrease wear, provide smooth operation and extend the service life of the lift. When servicing the lift at the recommended intervals, inspection and lubrication procedures specified in the previous sections should be repeated. Clean the components and the surrounding area before applying lubricants. LPS2 General Purpose Penetrating Oil is recommended where Light Oil is called out. Use of improper lubricants can attract dirt or other contaminants which could result in wear or damage to the components. Platform components exposed to contaminants when lowered to the ground may require extra attention. Lift components requiring grease are lubricated during assembly procedures. When these com- ponents are replaced, grease must be applied during installation procedures. Specified lubricants are available from The Braun Corporation (part numbers provided below). WARNING Maintenance and lubrication procedures must be performed as specified by an authorized service technician. Failure to do so may result in serious bodily injury and/or property damage. All listed inspection, lubrication and maintenance procedures should be repeated at “750 cycle” intervals following the scheduled “4500 Cycles” maintenance. These intervals are a general guideline for scheduling maintenance procedures and will vary according to lift use and conditions. Lifts exposed to severe conditions (weather, environment, contamination, heavy usage, etc.) may require inspection and maintenance procedures to be performed more often than specified. Discontinue lift use immediately if maintenance and lubrication procedures are not properly performed, or if there is any sign of wear, damage or improper operation. Contact your sales representative or call The Braun Corporation at 1-800-THE LIFT. One of our national Product Support representatives will direct you to an authorized service technician who will inspect your lift. Lubricant Type Specified (recommended) Lubricant Available Amount LPS2, General Purpose Penetrating Oil 11 oz. Aerosol Can 15807 Light Penetrating Oil (30 weight or equivalent) Light Oil Braun Part No. Door-Ease Stainless Stick Style (tube) Door-Ease Stick (tube) 1.68 oz. 15806 Light Grease Light Grease (Multipurpose) Lubriplate 14 oz. Can 15805 #YCLES Downstop pivot points (2) Apply Light Oil - See Lubrication Diagram Upper lift rod pin Apply Light Oil - See Lubrication Diagram Lower lift rod pin Apply Light Oil - See Lubrication Diagram Kickout spring (located in switch arm) Apply Light Oil - See Lubrication Diagram Platform hinges (6) Apply Light Oil - See Lubrication Diagram Outboard barrier latch Apply Light Oil - See Lubrication Diagram Perform all procedures listed in previous section also #YCLES Inboard locator latch mechanism Apply Light Grease - See Lubrication Diagram Check mounting hardware Tighten, repair or replace if needed. Check all fasteners (snap rings, nuts, hairpins, etc.) Tighten, resecure or replace if needed. Check all pivot points for excessive wear Resecure, replace damaged parts or otherwise correct as needed. Note: Apply lubricant during reassembly procedures. Perform all procedures listed in previous sections also #YCLES Platform fold mechanism Apply Light Grease - See Lubrication Diagram Ballscrew / main drive Add Lucas Heavy Duty Oil Stabilizer Clean ground cable at battery and frame Main Drive Ballscrew (in Frame Tube - hidden) Drive Arms Check power cables #ONSECUTIVE Repeat all previously listed inspection, lubrica #YCLE tion and maintenance procedures at 750 cycle intervals. )NTERVALS Switch Arm Lift Rod Inboard Locator Latch Mechanism Platform Fold Mechanism (Under Cover) Downstop (hidden) Platform Hinges (6) Outer Barrier Latch
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1.1-111 About : 4e53a27d-b711-11d9-804b-fa6c2ec39a5a Create Date : 2006:02:20 07:55:43-05:00 Metadata Date : 2006:02:20 07:55:56-05:00 Modify Date : 2006:02:20 07:55:56-05:00 Creator Tool : Adobe InDesign CS2 (4.0.2) Document ID : adobe:docid:indd:4e53a27c-b711-11d9-804b-fa6c2ec39a5a Rendition Class : proof:pdf Instance ID : uuid:3bf4f2fa-a210-11da-8b4a-000d933553c2 Derived From Instance ID : f16d953c-b705-11d9-804b-fa6c2ec39a5a Derived From Document ID : adobe:docid:indd:b3d8b010-b6ec-11d9-804b-fa6c2ec39a5a Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Y Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Document ID : uuid:6df339b5-b34e-11d9-a344-000d933553c2, uuid:6df339b5-b34e-11d9-a344-000d933553c2, uuid:6df339b5-b34e-11d9-a344-000d933553c2, uuid:6df339b5-b34e-11d9-a344-000d933553c2, uuid:6df339b5-b34e-11d9-a344-000d933553c2, uuid:6df339b5-b34e-11d9-a344-000d933553c2, uuid:6df339b5-b34e-11d9-a344-000d933553c2, uuid:6df339b5-b34e-11d9-a344-000d933553c2 Format : application/pdf Producer : Adobe PDF Library 7.0 Trapped : False Page Count : 8 Creator : Adobe InDesign CS2 (4.0.2)EXIF Metadata provided by EXIF.tools