CETIS AC9105S DECT Telephone User Manual

CETIS,INC. DECT Telephone Users Manual

a href="https://usermanual.wiki/CETIS" itemprop="url"> CETIS >

Users Manual

iPhone DECT Cordless Series User GuideFor Models AC8205S, AC8210S (1.8 GHz) and AC9205S, AC9210S (1.9 GHz)Preparing to Use the AC8200/AC9200 Series1.  Prepare to install the battery into the cordless handset    by removing the battery cover  and sliding it off. If cover is    secured with a screw, remove the screw first.2. Insert the battery connector into the handset’s connector.  The connector is “keyed” so it only goes in one way.  Do not force the connection.Note: The handset may “beep” when the battery is  connected. This is not an indication that the telephoneis ready to use. To obtain optimal performance of thetelephone, be sure to charge the battery for 10 to 12 hours.3. Replace the battery compartment cover and the    retaining screw.4. Insert the provided rubber screw cover.5. Turn the telephone base so the back panel is facing you.  Insert either end of the RJ-45 cable into the jack on the       back of the telephone labeled LINE.6. Insert the other end of the cable into the jack on the AC  adapter labeled PHONE.7. Insert one end of the RJ-11 line cord into the jack on the     AC adapter labeled LINE.8. Insert the other end of this line cord into a telephone jack.9. Plug the AC adapter into an unswitched electrical outlet.10. Remove the plastic overlay and place the paper faceplate    (supplied separately) over the keys. Replace the plastic    overlay by hooking the tabs on the overlay into the    recessed slots located on both sides.11. Place the cordless handset on the base unit.    The handset/base registration process will occur.Handset/Base Registration ProcedureThis procedure establishes an exclusive link between a specifichandset and base, thereby allowing no other access to thisspecific base. To accomplish this procedure, place the handseton the base in the charging position. The LINE indicator willblink while the registration process is occuring. This process only occurs the first time a handset is placed on the charging cradle of a new base.Charging the BatteryThe rechargeable Lithium-Polymer battery must be fully charged before using the phone for the first time. It is recommended that the battery be charged for approxi-mately 10 to 12 hours without interruption before use.To charge the battery, place the handset, keypad down, in the base unit. Ensure that  the CHARGE LED on the base lights.If the LED Does Not Light:1. Ensure that the AC adapter is plugged in.2. Ensure that the AC adapter is plugged into an unswitched  electrical outlet.3. Ensure that the handset charging contacts at the bottom of  the handset are making good contact with the base unit’s  charging contacts.Cleaning the Battery ContactsTo maintain a good charge, it is important to clean all  charging contacts on the handset and base unit. Use a  pencil eraser or other contact cleaner. Do not use any  liquids or solvents.Battery Safety Instructions1. Use only Teledex-approved battery replacements.2. Dispose of the Lithium-Polymer battery in any ordinary      trash receptacle.3. Do not dispose of battery in fire, as it may explode.4. Charge the battery only while in the handset, and only by  using the base unit to charge. Do not attempt to remove  the battery and charge it in a separate charging unit.5. Do not short-circuit the battery, as this may cause it to  explode or catch fire.Adjusting the Ring Volume and Assigning Ring TonesThe UP and DOWN volume keys will adjust the ringer volume of the telephone. To adjust ring volume, press either the UP and DOWN volume key when the handset is on the bse cradle and the phone is not active (off-hook). There are four ring tones that can be assigned individually to either line (on two-line models) to audibly identify the ringing line. Additionally, the AC8200/AC9200 series features a programmable “crescendo” ring mode, wherein the ring volume begins at the lowest setting, then rings progressively louder with each ring during an incoming call. To assign a ring tone to a line (normal ring mode):1. Press the FLASH key (see Fig. 1); then a key on the dial pad  from 1-4, depending on the desired ring tone. The phone  will ring once to provide a sample of the selected ring  tone. 2. When you have selected a suitable ring tone, press the  STORE key (see Fig. 1), then a number on the dial pad for  the desired line assignment (i.e.; ‘1’ for line 1, ‘2’ for line 2).Cordless Handset AC AdapterBase Unit User GuideLithium Polymer BatteryClear Plastic Overlay Rubber Battery Screw Cover Phillips Screw15-foot, 8-wire Cable   (with RJ-45 connector)10-foot, 4-wire Line Cord     (with RJ-11 connector)Included in Your Package
To assign a ring tone to a line (crescendo ring mode):1. Select desired ring tone: Press the FLASH key (see Fig. 1);  then a key on the dial pad from 1-4, depending upon the  desired ring tone. The phone will ring once to provide a  sample of the selected ring tone. 2. Assign ring tone to a line: When you have selected a sui  able ring tone, press the STORE key (see Fig. 1), then press  number ‘3’ on the dial pad to assign the ring tone to line 1,  or number ‘4’ on the dial pad to assign the ring tone to  line ‘2’.To return to regular ring mode: 1. Press the FLASH key; then the number ‘1’ on the dial pad.2. Press the STORE key; then the number on the keypad that  corresponds to the line for which you wish to change back  to regular ring mode.Adjusting Speakerphone VolumeThe speakerphone has eight (8) levels. To adjust speaker-phone volume, locate the volume up/down keys, located on the front of the phone to the left of the keypad. With the speaker active, press the “down” arrow key to decrease the volume level, and press the “up” arrow key to increase it.Adjusting Handset Receive VolumeThe handset has eight (8) volume levels. To adjust the handsetvolume, locate the volume up/down keys, located on thehandset, below the “#” key. Pressing the UP arrow key willdecrease the volume level, while pressing the DOWN arrow key will increase it.Auto Dial KeysThe AC8200/AC9200 series has either five (5) or ten (10)  programmable guest service (auto dial) keys, depending  on the model you own. These keys can be programmed  to automatically dial telephone numbers, or to activate  telephone system features. To program the auto dial  keys (programming can only be done from base unit):1. With the phone “on hook” (inactive) and the faceplate  removed, press the recessed STORE key (see diagram).2. Enter the desired telephone number (up to 15 digits in  length) to be stored. To enter a “pause” in the number  string, press the REDIAL key as necessary.3. Press the STORE key again.4. Press the auto dial key where the number is to be stored.  Programming is now complete for that auto dial key.  To program additional keys, repeat this process.Selecting Line 1 and Line 2 (two-line models only)The AC8200/9200 series employs PrimeLine/RingLine Select,so selecting the correct line is as easy as lifting the handset.This feature prioritizes the ringing or idle line and reduces theconfusion of line selection. You may also manually select the desired line by pressing either Line 1 or Line 2 keys.Receiving a CallAn audible ring and flickering red LED indicate an  incoming call.To answer a call using the handset while it is not on  the base:1. Pick up the handset.2. Press the line key for the ringing line. The handset will go  “off-hook” answering the ringing line.3. To end the call, place the handset in the base unit cradle,    or press the illuminated line key on the handset.To answer a call using the handset while it is resting on  the base:1. Pick up the handset from the base. The phone will  automatically connect to the correct, ringing line.2. To end the call, replace the handset in the base unit cradle,  or press the illuminated line key on the handset.To answer a call using the speakerphone:1. Press the line key for the ringing line. The speakerphone     will go “off-hook”, answering the ringing line.2. Alternatively, press the SPKR key. The phone will automat  cally select the correct, ringing line.3. To end the call, press the SPKR key or the active line   again.Placing a CallUsing the handset:1. Pick up the handset and select either line 1 or line 2.  Listen for dial tone and dial the desired number, or press    an auto dial key to dial a preprogrammed number.2. After the call is complete, press the key for the selected       line again to end the call.Using the speakerphone:1. Press a key for either line 1 or line 2, or press SPKR.2. Listen for dial tone, and dial the desired number, or press    an auto dial key to dial a preprogrammed number.3. After the call is complete, press the SPKR key to end call.RedialThe AC8200/AC9200 series can automatically redial the last number dialed. On either the handset or base, press theREDIAL key to redial the last number.Conference (two-line models only)The CONF key allows for three-way conversations. Dependingon the situation, you may initiate a conference call using one of these methods:User initiates two calls:1. Place call to first party, then place them on hold by  pressing the HOLD key.2. Using the second line, place call to second party.3. Once that party is on the line, press CONF to join all three  parties.User initiates one call:1. After receiving a call from first party, place them on hold  by pressing the HOLD key.2. Using the second line, place call to the second party.3. Once that party is on the line, press CONF to join all three  parties.User includes two parties:1. After receiving a call from first party, place them on hold  by pressing the HOLD key.2. After receiving call from second party, press CONF to join  all three parties.To terminate a conference call, pressing a line key will  maintain the connection with that line, while dropping the other line. To terminate the call entirely, press either the CONF key or SPKR key to disconnect both parties.
Download:
Mirror Download [FCC.gov]
Document ID1769591
Application IDYIm2st/WXnvqo74plP+A8g==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize45.86kB (573196 bits)
Date Submitted2012-08-18 00:00:00
Date Available2012-08-18 00:00:00
Creation Date2007-09-12 13:01:50
Producing SoftwareAdobe PDF Library 7.0
Document Lastmod2012-08-13 18:20:10
Document TitleUsers Manual
Document CreatorAdobe InDesign CS2 (4.0.5)
FCC ID Filing: ZTUAC9105S

Navigation menu