Cabelas Grinder Foot Pedal 08 0901 Users Manual
Cabelas Grinder Foot Pedal 08-0901 cabelas_grinder_footprdal_519300
08-0901 to the manual 428e6786-6438-44e6-bbf2-240220ab5b78
2015-02-04
: Cabelas Cabelas-Cabelas-Grinder-Foot-Pedal-08-0901-Users-Manual-364414 cabelas-cabelas-grinder-foot-pedal-08-0901-users-manual-364414 cabelas pdf
Open the PDF directly: View PDF .
Page Count: 2
Download | |
Open PDF In Browser | View PDF |
ATTENTION If any components of this unit are broken or the unit does not operate properly, please contact Cabela’s Customer Service. Model No. 08-0901 Retail Store Purchases: 1-800-905-2731 (U.S. & Canada) Catalog and Internet Purchases: 1-800-237-8888 All International: 1-308-234-5555 DO NOT RETURN THE UNIT TO THE STORE WHERE IT WAS PURCHASED! Before beginning the assembly, check the package contents for all of the parts. If you are missing any parts, or if any parts are damaged, contact Cabela’s Customer Service- Retail Store Purchases 1-800-905-2731 (U.S. & Canada) / Catalog & Internet Purchases: 1-800-237-8888 / All International: 1-308-234-5555 WARNING! REV041309 SAVE THESE INSTRUCTIONS! REFER TO THEM OFTEN AND USE THEM TO INSTRUCT OTHERS. Before attaching or detaching the Foot Pedal to the grinder, make sure the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE and the power switch is in the OFF position. ALWAYS unplug the Foot Pedal and the grinder when not in use. ALWAYS FOLLOW THE MANUFACTURER’S INSTRUCTIONS AND SAFETY GUIDELINES THE COME WITH THE GRINDER AND THE FOOT PEDAL. INSTALLATION IMPORTANT SAFETY RULES WARNING! READ AND FULLY UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO USING THIS UNIT. YOUR SAFETY IS MOST IMPORTANT! FAILURE TO COMPLY WITH PROCEDURES AND SAFEGUARDS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE. REMEMBER: YOUR PERSONAL SAFETY IS YOUR RESPONSIBILITY! 1. DO NOT use the grinder and the Foot Pedal without the grinder properly set up in accordance to the manufacturer’s guidelines. 2. Using the Foot Pedal on grinders without proper point of operation measures and protection can cause serious injury. Follow the grinder’s manufacturer safety guidelines. DO NOT use the Foot Pedal on grinders without proper installation. 3. The Foot Pedal should be utilized so that the operator’s hands and fingers cannot enter dangerous areas of the grinder. KEEP FINGERS CLEAR of the Auger and Cutting Blades AT ALL TIMES. NEVER REACH INTO THE GRINDER, doing so may cause serious injury. ALWAYS USE THE PROVIDED STOMPER, NEVER FEED FOOD BY HAND. NEVER use fingers to scrape food away from the Grinding Plate while the Grinder is in operation. SEVERE INJURY MAY RESULT. 4. ALWAYS DISCONNECT grinder and the Foot Pedal from power source before servicing, changing accessories, plates or knives or cleaning the unit. 5. Plug the grinder and the Foot Pedal into a standard 120 Volt, 60 Hz wall outlet. 6. DO NOT USE the grinder and the Foot Pedal if the Power Cord, Plug or any other parts are damaged. If the Power Cord, the grinder or the Foot Pedal are damaged, call Customer Service. DO NOT ATTEMPT TO REPLACE THE CORD. Be sure to not allow the Power Cord to drape into your work area. Check that all parts are operating properly, and perform the intended functions. Check for alignment of moving parts or any other conditions that may affect the operation. DO NOT use extension cords. 7. NEVER use any accessories or parts from other manufacturers. Doing so will VOID YOUR WARRANTY and may cause fire, electrical shock or injury. 8. TO PROTECT AGAINST RISK OF ELECTRICAL SHOCK: DO NOT SUBMERGE THE GRINDER OR THE FOOT PEDAL INTO WATER OR LIQUID. BE SURE THE GRINDER AND THE FOOT PEDAL ARE DISCONNECTED FROM THE POWER SOURCE BEFORE CLEANING. DO NOT use near water or liquids. 9. Be sure the Foot Pedal is on the, clean, dry floor. 10. Reduce risk of unintentional starting. Make sure the power switch of the grinder is in the “OFF” position before attaching to the power source. WARNING! Before attaching or detaching the Foot Pedal to the grinder, make sure the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE and the power switch is in the OFF position. ALWAYS unplug the Foot Pedal and the grinder when not in use. ALWAYS FOLLOW THE MANUFACTURER’S INSTRUCTIONS AND SAFETY GUIDELINES THE COME WITH THE GRINDER AND THE FOOT PEDAL. 1. Be sure the power switch on the grinder is in the ‘OFF’ position. 11. NEVER LEAVE THE GRINDER AND THE FOOT PEDAL UNATTENDED. Be safe, DISCONNECT the grinder and the Foot Pedal from power source before leaving the work area. Close supervision is necessary when any appliance is used near children. This appliance is NOT to be used by children. 2. Plug the power cord on the grinder into the back of the plug on the Foot Pedal. 12. TIE BACK loose hair and clothing, and roll up long sleeves before operating the grinder and the Foot Pedal. REMOVE ties, rings, watches, bracelets, or other jewelry before operating the grinder and the Foot Pedal. 4. Turn the switch grinder switch to the ‘ON’ position. 13. Be sure the grinder is on a stable work surface. Be sure all the grinder feet are stable. 14. ONLY use the Foot Pedal with shoes on. NEVER use the Foot Pedal with bare or stocking feet. 3. Plug the Foot Pedal into a 110 Volt electric outlet. 5. The grinder will not operate until the Foot Pedal is depressed with your foot. 6. To stop the grinder, release the pressure on the Foot Pedal by raising your foot. 15. The Foot Pedal may become HOT during operation. This is normal. DO NOT touch the Foot Pedal parts during operation or until they cool after use. 16. ONLY use the Foot Pedal on hard, flameresistant surfaces. DO NOT use the Foot Pedal on carpeted surfaces. 17. Keep the area around the Foot Pedal clear of all objects to avoid accidental ignition. NEVER place an object on the Foot Pedal to keep the grinder running. The Foot Pedal is intended for intermittent grinding and stuffing. 18. This product is not intended for commercial use. Commercial use will void the warranty. 19. WEAR EYE PROTECTION. Wear safety glasses. Everyday eye glasses are not safety glasses. Safety glasses conform to ANSI Z87.1 requirements. Note: approved safety glasses have Z87 printed or stamped on them. 20. DO NOT use outdoors. 21. The Foot Pedal is intended for use with Grinders ONLY. 22. DO NOT use the grinder and the Foot Pedal while under the influence of drugs, medications or alcohol. 23. DO NOT let the Power Cord hang over edge of work surface during operation. SAVE THESE INSTRUCTIONS! Refer to them often and use them to instruct others. GROUNDING INSTRUCTIONS GROUNDING This appliance must be grounded while in use to protect the operator from electrical shock. The appliance is equipped with a 3-conductor cord and a 3-prong grounding type plug to fit the proper grounding-type receptacle. The appliance has a plug that looks like Figure A. An adaptor, Figure B, should be used for connecting Figure A plugs to two-prong receptacles. The grounding tab which extends from the adaptor must be connected to a permanent ground such as a properly grounded outlet box as shown in Figure C using a metal screw. Circuit Grounding Conductor Figure A Grounding Prong Figure B Figure C Metal Grounding Screw Cover of Grounded Outlet Box Grounding Means AA2220
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.2.2-c063 53.352624, 2008/07/30-18:12:18 Instance ID : uuid:73511358-640c-4680-b9c7-a2f05bf6def7 Document ID : xmp.did:E2224ADB4E24DE118E40D7D42A29BEC6 Original Document ID : adobe:docid:indd:8922f6c9-f927-11dd-97f8-a993e4d318cb Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:E1224ADB4E24DE118E40D7D42A29BEC6 Derived From Document ID : adobe:docid:indd:8922f6c9-f927-11dd-97f8-a993e4d318cb Derived From Original Document ID: adobe:docid:indd:8922f6c9-f927-11dd-97f8-a993e4d318cb Derived From Rendition Class : default History Action : saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:DF224ADB4E24DE118E40D7D42A29BEC6, xmp.iid:E0224ADB4E24DE118E40D7D42A29BEC6, xmp.iid:E1224ADB4E24DE118E40D7D42A29BEC6, xmp.iid:E2224ADB4E24DE118E40D7D42A29BEC6, xmp.iid:E3224ADB4E24DE118E40D7D42A29BEC6, xmp.iid:E4224ADB4E24DE118E40D7D42A29BEC6, xmp.iid:6CA797F73B25DE118E40D7D42A29BEC6, xmp.iid:A2AA4FB83128DE11BE36C608A7CB119D, xmp.iid:A3AA4FB83128DE11BE36C608A7CB119D History When : 2009:04:08 16:08:45-04:00, 2009:04:08 16:08:45-04:00, 2009:04:09 12:04:28-04:00, 2009:04:09 12:04:28-04:00, 2009:04:09 12:04:54-04:00, 2009:04:09 15:07:34-04:00, 2009:04:09 15:23:55-04:00, 2009:04:13 09:48:07-04:00, 2009:04:13 09:48:48-04:00 History Software Agent : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0 History Changed : /, /metadata, /metadata, /;/metadata, /, /, /, /, / Manifest Link Form : ReferenceStream, ReferenceStream Manifest Placed X Resolution : 300.00, 300.00 Manifest Placed Y Resolution : 300.00, 300.00 Manifest Placed Resolution Unit : Inches, Inches Manifest Reference Instance ID : uuid:762913656BF4D911A5FCCD02FCA7D69B, xmp.iid:BB20E0F07A24DE1189F3FF43C86B780A Manifest Reference Document ID : uuid:752913656BF4D911A5FCCD02FCA7D69B, xmp.did:E4BB65404E24DE1189F3FF43C86B780A Create Date : 2009:04:13 09:49:37-04:00 Modify Date : 2009:04:13 09:49:42-04:00 Metadata Date : 2009:04:13 09:49:42-04:00 Creator Tool : Adobe InDesign CS4 (6.0) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 9812 bytes, use -b option to extract) Doc Change Count : 2283 Format : application/pdf Producer : Adobe PDF Library 9.0 Trapped : False Page Count : 2 Creator : Adobe InDesign CS4 (6.0)EXIF Metadata provided by EXIF.tools