Chamberlain Group The XCVR1 Remote Control Transceiver User Manual

Chamberlain Group Inc, The Remote Control Transceiver 114A3884 T1000 R1000 indd

a href="https://usermanual.wiki/Chamberlain-Group-The" itemprop="url"> Chamberlain Group The >

Exhibit D Users Manual per 2 1033 b3

6 For Technical Support Please Call: 1-888-528-7826 www.chamberlainaccess.com © Chamberlain Access Solutions All Rights Reserved Troubleshooting Repeater service alerts are managed in the overlock management software. In the software, go to Tools\Manage Repeaters to view and clear alerts. Low Battery Indication The battery power on the R1000 repeater is supervised by the Overlock Management Software. A low battery indication will generate an alert in the software, notifying the administrator. 114A3884 ACCESSMASTER T1000 TRANSCEIVER AND ACCESSMASTER R1000 REPEATER INSTALLATION MANUAL
T1000 Overview The T1000 transceiver is designed to allow communication between the AccessMaster Overlock and the Falcon XT access control system. The T1000 transceiver provides a secure, reliable wireless mode of communication without the need to run excess wiring throughout the site. The T1000 is designed to work only with the R1000 repeater and/or the OL1000 overlock device. Wiring the Transceiver Remove the bottom panel of the T1000 transceiver to view the power and communication pins. Power and Communication from the XT to the Transceiver Power from the XT to the transceiver is provided via RS422 (18 AWG, single-pair, stranded, tinned copper) using 12 VDC. The power wire is connected to pins 5 and 6 on the transceiver port. Connect the positive 12 VDC to pin 5 and ground to pin 6. Wire for communications must be 24 AWG, 2-pair, stranded, tinned copper, individual shield, drain wire, low capacitance wire. Communication connections on the transceiver are made on pins 1, 2, 3, and 4. Communication to the XT occurs on pin 1 (TX+) and pin 2 (TX-). Communication from the XT occurs on pin 3 (RX-) and pin 4 (RX+). Wiring connections are shown on page 2. ACCESSMASTER T1000 Transceiver (T1000) or Antenna Screws Repeater (R1000) AC/DC Power Supply Screws Carton Inventory 5 Mounting the R1000 Prior to mounting the repeater, write down the serial number of the device. This number will be needed during programming. Use the following guidelines when mounting the repeater. Mount the unit within 50 ft of a power source • Mount the unit in an area protected from the • weather Mount the unit as high as possible on the site • (such as near the roof ine) using the provided mounting screws Mount the unit to a solid, nonmetal surface • The unit should be halfway between the • devices that need to communicate. The unit is weather-resistant • Warning: Do not try to add length to the antenna to extend the repeater’s range as this will cause the system to become inoperational and/or will exceed FCC requirements. Installing Multiple Repeaters On large sites, multiple repeaters may be required to provide adequate communication coverage. Up to 8 repeaters can be learned to one transceiver, with up to 64 repeaters to one site. R1000 Operation The R1000 repeater extends the range of the T1000 transceiver to cover larger areas. Repeaters should be located throughout the site in such a way that coverage overlaps slightly to provide the most complete coverage. Up to 8 repeaters can be programmed to communicate with one transceiver. NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that may cause undesired operations. FCC ID: HBWGCU2 IC:2666A-GCU2
Download:
Mirror Download [FCC.gov]
Document ID1229765
Application IDosg4XsiyD9pyPS3YliyyJA==
Document DescriptionExhibit D Users Manual per 2 1033 b3
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize48.49kB (606128 bits)
Date Submitted2010-01-19 00:00:00
Date Available2010-01-19 00:00:00
Creation Date2009-03-31 09:35:10
Producing SoftwareAcrobat Distiller 8.1.0 (Windows)
Document Lastmod2010-01-14 08:27:44
Document Title114A3884_T1000_R1000.indd
Document CreatorPScript5.dll Version 5.2
Document Author: kgoodfriend
FCC ID Filing: HBWXCVR1

Navigation menu