Codan Radio Communications AMP-4-800 700/800 MHz 30W POWER AMPLIFIER User Manual

Codan Radio Communications 700/800 MHz 30W POWER AMPLIFIER Power Amplifier AMP 4 410 30 00

a href="https://usermanual.wiki/Codan-Radio-Communications" itemprop="url"> Codan Radio Communications >

User Manual

    RF Exposure Warning Exposure to radio frequency (RF) energy has been identified as a potential environmental factor that must be considered before a radio transmitter can be authorized or licensed. The FCC and IC have therefore developed maximum permissible exposure (MPE) limits for field strength and power density, listed in FCC 47 CFR § 1.1310 and IC RSS-102 Issue 2 Sect 4. The FCC has furthermore determined that determination of compliance with these exposure limits, and preparation of an Environmental Assessment (EA) if the limits are exceeded, is necessary only for facilities, operations and transmitters that fall into certain risk categories, listed in FCC 47 CFR § 1.1307 (b), Table 1. All other facilities, operations and transmitters are categorically excluded from making such studies or preparing an EA, except as indicated in FCC 47 CFR §§ 1.1307 (c) and (d). Revised FCC OET Bulletin 65 (Edition 97-01) and IC RSS-102 Issue 2 provide assistance in determining whether a proposed or existing transmitting facility, operation or device complies with RF exposure limits. In accordance with OET Bulletin 65, FCC 47 CFR § 1.1307 (b) and RSS-102 Issue Sect 2.5, the Codan Radio Communications transmitter manufactured in Canada is categorically excluded from routine evaluation or preparing an EA for RF emissions and this exclusion is sufficient basis for assuming compliance with FCC/IC MPE limits. This exclusion is subject to the limits specified in FCC 47 CFR §§ 1.1307 (b), 1.1310 and IC RSS-102 Issue 2 Sect 4. Codan Radio Communications has no reason to believe that the excluded transmitter encompasses exceptional characteristics that could cause non-compliance.  Notes: • The FCC and IC’s exposure guidelines constitute exposure limits, not emission limits. They are relevant to locations that • are accessible to workers or members of the public. Such access can be restricted or controlled by appropriate means (i.e., fences, warning signs and others).  • The FCC and IC’s limits apply cumulatively to all sources of RF emissions affecting a given site. Sites exceeding these • limits are subject to an EA and must provide test reports indicating compliance. RF Safety Guidelines and Information Base and Repeater radio transmitters are designed to generate and radiate RF energy by means of an external antenna, typically mounted at a significant height above ground to provide adequate signal coverage. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that permitted for successful communication. The following antenna installation guidelines are extracted from Appendix A from OET Bulletin 65 and must be adhered to in order to ensure RF exposure compliance:  Non-building-mounted Antennas: • Height above ground level to lowest point of antenna ≥ 10 m • Power ≤ 1000 W ERP (1640 W EIRP) Building-mounted Antennas:         Power ≤ 1000 W ERP (1640 W EIRP) The following RF Safety Guidelines should be observed when working in or around transmitter sites: • The minimum safe distance the user should be from the transmitter antenna while transmitting is 57 cm amplifiers 30W or less. This assumes a maximum antenna EIRP of 15 dBi. • Do not work on or around any transmitting antenna while RF power is applied.  • Before working on an antenna, disable the appropriate transmitter and ensure a “DO NOT USE” or similar sign is placed on or near the PTT or key-up control. • Assume all antennas are active unless specifically indicated otherwise.  • Never operate a transmitter with the cover removed. • Ensure all personnel entering a transmitter site have electromagnetic energy awareness training.  For more information on RF energy exposure and compliance, please refer to the following: • FCC Code of Regulations; 47 CFR §§ 1.1307 and 1.1310  • FCC OET Bulletin 65, Edition 97-01, “Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields” • http://www.fcc.gov/oet/rfsafety/  • IC RSS-102 Issue 2, “Radio Frequency Exposure Compliance of Radio Communication Apparatus”
 2 FCC Part 90.203(e) Compliance  This radio complies with 47 CFR Part 90.203(e) in that the operator cannot program and transmit on frequencies, other than those stated by the manufacturer, service or maintenance personnel, using the equipment's external operation controls. It is noted that the FCC rules would be violated if this radio is used to operate on frequencies outside of FCC (Part 90 and Part 22) Frequency Bands for users other than the (Federal Government).  FCC RF Exposure Requirements  CAUTION: This transmitter must be restricted to work related operations in a Controlled RF exposure environment. All qualified end-users of this device must have the knowledge to control their exposure conditions and/or duration, and the exposure conditions and/or duration of their passengers and bystanders, to comply with the General Population / Uncontrolled MPE limit and requirements.  IC RSS-GEN, Sec 7.1.2 Warning Statement- (Required for Transmitters)  ENGLISH: Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.  FRENCH: Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée quivalente (p.i.r.e.) ne dépassepas l'intensité nécessaire à l'établissement d'une communication satisfaisante.  IC RSS-102, Sec 2.6 Warning Statements  ENGLISH: The applicant is responsible for providing proper instructions to the user of the radio device, and any usage restrictions, including limits of exposure durations. The user manual shall provide installation and operation instructions, as well as any special usage conditions, to ensure compliance with SAR and/or RF field strength limits. For instance, compliance distance shall be clearly stated in the user manual.  The user manual of devices intended for controlled use shall also include information relating to the operating characteristics of the device; the operating instructions to ensure compliance with SAR and/or RF field strength limits; information on the installation and operation of accessories to ensure compliance with SAR and/or RF field strength limits; and contact information where the user can obtain Canadian information on RF exposure and compliance. Other related information may also be included.  FRENCH: Le demandeur est tenu de fournir des instructions appropriées à l'utilisateur de l'appareil de radio, et des restrictions d'utilisation, y compris les limites de durée d'exposition. Le mode d'emploi doit fournir installation et de fonctionnement des instructions, ainsi que les conditions d'utilisation particulières, pour assurer la conformité avec SAR et / ou les limites d'intensité de champ RF. Par exemple, la distance de conformité doit être clairement indiqué dans le mode d'emploi.  Le manuel d'utilisation de dispositifs destinés à un usage contrôlé doit également contenir des
Download:
Mirror Download [FCC.gov]
Document ID2361547
Application IDLVlR+2ly0YxjgIn9zHQ6Sg==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize4.04kB (50544 bits)
Date Submitted2014-08-18 00:00:00
Date Available2014-08-18 00:00:00
Creation Date2014-06-25 08:18:17
Producing SoftwareAdobe PDF Library 10.0
Document Lastmod2014-06-25 08:18:29
Document TitlePower Amplifier AMP-4-410-30-00
Document CreatorAcrobat PDFMaker 10.1 for Word
Document Author: USER
FCC ID Filing: H4JAMP-4-800

Navigation menu