DEVELOPMENT BT0445DS LED Shop Light User Manual

INTERNATIONAL DEVELOPMENT COMPANY LED Shop Light BT0445DS0620 IM E 2018 8 31

a href="https://usermanual.wiki/DEVELOPMENT" itemprop="url"> DEVELOPMENT >

User manual

PROBLEMLight will not come on.Linked Lights to do not turn on.A. Fixture not properly connected.B. Pull chain not engaged.C. Fixture not receiving power.A. A.A. Check wires to ensure proper connections.B. Pull chain to activate light.C. Check to make sure breaker is on and test another working electrical device to make sure it is receiving power.Check all linked shop lights ensuring power cords are all properly installed.POSSIBLE CAUSE SOLUTIONFCC WARNING:WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.NOTES: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.TROUBLE SHOOTING17”11”Fold FoldFold FoldLED 4' Linkable Shop Light with Bluetooth SpeakerUse And Care Guide Read And Save This Instructions Before UseENModel: BT0445DS0620EN | 4Bluetooth audio does not work.Audio can be heard out of first shop light only in linked chain.A. Check to make sure aux cables are properly installed on all linked lights.Linked power cords may not be plugged in.A. Bluetooth not active or not close enough to device.B. Bluetooth may be paired to wrong device.C. Device volume may be low or muted.A. Ensure your device's Bluetooth is turned on, in range and discoverable.B. Make sure you are selecting the correct device to pair to.C. Makes sure your audio level is set appropriately.A. Aux Cords are not connected on linked lights.**********************************************************************************************NOTE: The Bluetooth brand elements may not be used in a fashion or manner that could impair or otherwise damage the goodwill associated with the Bluetooth brand or the Fellow Adopters (Sky Rich Star Limited). The Bluetooth brand elements shall therefore not be used in connection with products and services that do not enable any Bluetooth wireless functionality or in connection with unlawful, obscene, pornographic, excessively violent, hazardous,or otherwise poor-taste activities.International Development Company899 Henrietta Creek Rd. Roanoke,Roanoke, TX 76262 USAToll-free: 1-877-723-0723Made in China© 2018 IDC, all rights reserved. The Honeywell Trademark is used under license from Honeywell International Inc. Honeywell International Inc. makes no representations or warranties with respect to this product. This product is manufactured forInternational Development Company.IC WARNINGThis device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:(1) This device may not cause interference; and(2) This device must accept any interference, including interference that may cause undesired operation of the device.
INSTALLATION HOW TO OPERATE BLUETOOTH SPEAKER:CONNECTION OPTIONSSAFETY INFORMATIONPRE-INSTALLATIONIMPORTANT: Read all safety precautions and installations carefully before installing or servicing this fixture.• 5.25’ power cord with plug, link up to 8 shoplight together.• Do not handle any energized fixture or attempt to energize any fixture with wet hands or while standing on a wet or damp surface or in water.• Assure that the fixture is mounted onto a structurally sound surface that will support the fixture.• The fixture is designed for use in a 120 VAC, 60Hz fused circuit. Do not use on a dimming circuit.• Do not look into the lights.• Product is intended for use in garages, basements, work areas, utility rooms and recreation rooms.• Maximum distance to the receptacle is determined by the length of the cord provided. (5.25 ft, 3-prong, 120V grounded plug included)• Includes a protective sleeve, such as 0.010-inch (0.25-mm) thick fiberglass, where the path of cord travel to the ceiling-mounted receptacle is not between the two supporting chains.• The fixture is intended to be installed directly beneath a ceiling-mounted receptacle. Excess cord should be secured to one of the supporting chains with a cable tie to keep it out of the work space.• Use hook to support chain, not the electrical cord.• Do not install on radiant-heating type ceiling.• Maximum distance to the receptacle is determined by the length of cord provided.WARNING: Failure to comply with these instructions could result in a potentially fatal electric shock and/or property damage.• Carefully remove the fixture from the carton and check to make sure that all hardware is included.• Be careful not to misplace any of the hardware needed for installing the fixture. If all hardware is not included, call customer service number.PLANNING INSTALLATIONHARDWARE INCLUDEDNOTE: The unit is intended to be installed directly beneath a ceiling-mounted receptacle. If there is excess cord, bind with string or a cable tie to keep it out of work space.ATTACH THE CEILING HOOKSATTACH THE “S” HOOKSInsert the “S” hooks (Part BB) into each of the holes on both sides of the shop Light.(Figure 1)NOTE: A maximum of 8 lights can be connected off of a single circuit. LINKING CABLE ATTACH THE HANGING CHAIN1. Using two hanging chains (Part AA) attach a hanging chain to one of the “S” hooks (Part BB) previously attached to each side of the light fixture. (Figure 2) NOTE: The hanging chain must be bent in half in order to attach each side to an “S” hook.2. Attach two additional “S hooks” (Part BB) to the center of each hanging chain previously attached.3. Attach the remaining hanging chains (Part AA) to the “S” hooks (Part BB) previously attached.4. Adjust chain manually to achieve desired height.5. Attach the remaining “S” hooks (Part BB) to the hanging chains and attach to the ceiling hooks.6. Determine whether a single or multiple units are to be installed. If multiple units will be installed follow steps in CONNECTION OPTIONS section. Connect lights per instructions andrepeat steps 1-5 (under Attach the Hanging Chain) for each light connected.7. Plug power cord into an outlet to use pull chain to power on.AA: 12 in. Hanging Chain (4)Maximum Weight: 7 kgs.BB: “S” Hook (8)2.0 mm x 25.4 mm x 11.6 mm CC: Ceiling Hook (2)3.0 mm x 54.5 mm x 15.6 mm(Figure 1)17”11”Fold FoldFold Fold AUX INPower Cord Plug AUX OUT Reflex PortReflex PortEN | 1 EN | 2 EN | 3NOTE: When linking shop lights, you should pair your Bluetooth with the first one in the linking chain, then connect all linked lights with provided aux cables. Only 1 light will be able to paired from a single device.Bluetooth Speaker will enter pairing mode when you turn on the light. Activate bluetooth on your device and find device named BT0445DS0620. Press to pair. The Bluetooth Speaker will turn off when the light is turned off.1. 2. Up to 8 units can be connected using the 5.25" power cord. Once installed, plug the power cord into the end of linked shop light and repeat up to 7 times.To link the audio in up to 8 shop lights connect the audio cable (Part EE) from the aux out on first shop light and then into the aux in on second shop light. Repeat for up to 8 lights.1. 2. EE: Audio cable (1) Length 1.5m AC Outlet Connect the power cord plug to shoplight AUX IN AUX OUTEEConnect ends of audio cable (Part EE) from Aux Out to Aux In on each linked shoplight(Figure 2)Bluetooth Speakers AC OutletFor better operation, the distance between Bluetooth device and the shop light had better less than 65.6ft(20m)(It depends on the Bluetooth device and the environment).65.6ft (20m)Choose desired location of light fixture making sure it is within reach of an outlet. Use a pencil to place a mark on the ceiling where each ceiling hook (Part CC) should go. Screw hooks in place until secure.MAX. 8 Units Only Connect To Adjacent Light FixtureMAX. 8 Units Only Connect To Adjacent Light Fixture
PROBLEMALa luminaria no enciende.Las Luces enlazadas no se encienden.A. El accesorio no está conectado correctamente. B. No ha jalado la cadena del interruptor.C. El accesorio no está recibiendo corriente. A. A. Verifique todas las luces del taller conectadas, y compruebe que los cables de alimentación estén instalados correctamente.CAUSA PROBABLE SOLUCIÓN SOLUCIÓN DE PROBLEMAS17”11”Fold FoldFoldLuz LED de 4 pies enlazable con Altavoz BluetoothGuía de Uso y CuidadoLea y Guarde Estas Instrucciones Antes de UsarESModelo: BT0445DS0620ES | 4El audio del Bluetooth no funciona.El audio puede escucharse desde la primera luz del taller solo en la cadena enlazada.A. Asegúrese de que los cables auxiliares estén instalados correctamente en todas las luces enlazadas.Los cables de alimentación enlazados no se pueden enchufar.A. Bluetooth no activado o lejos del dispositivo.B. Bluetooth emparejado con el dispositivo incorrecto.C. El volumen del dispositivo puede ser bajo o silenciarse.A. Compruebe que el Bluetooth de su dispositivo está encendido, dentro del rango de alcance y sea detectable.B. Asegúrese de seleccionar el dispositivo correcto para emparejar.C. Asegúrese de que su nivel de audio está ajustado correctamente.A. Los cables auxiliares no están conectados a luces enlazadas.A. Revise los cables para asegurar una conexión correcta. B. Jale la cadena del interruptor para activar la luminaria. C. Asegúrese que el interruptor de circuitos está encendido y pruebe con otro dispositivo electrónico que funcione para asegurarse de que esté recibiendo corriente. ADVERTENCIA FCC:ADVERTENCIA: Los cambios o modificaciones a esta unidad que no estén expresamente aprobados por la parte responsable del cumplimiento pueden anular la autoridad del usuario para operar el equipo.**********************************************************************************************NOTAS: Este equipo ha sido probado y se probó su compatibilidad con los límites para un Dispositivo Digital de Clase B, de conformidad con la Parte 15 de las Reglas de la FCC. Estos límites están diseñados para proporcionar una protección razonable contra interferencias dañinas en una instalación residencial. Este equipo genera, usa y puede radiar energía de radiofrecuencia y, si no se instala y utiliza de acuerdo con las instrucciones, puede causar interferencias perjudiciales a las comunicaciones de radio.Sin embargo, no hay garantía de que la interferencia no ocurra en una instalación en particular. Si este equipo causa una interferencia dañina a la recepción de radio o televisión, lo que puede determinarse apagando y encendiendo el equipo, se recomienda al usuario que intente corregir la interferencia mediante una o más de las siguientes medidas:• Reorientar o reubicar la antena receptora.• Aumentar la distancia entre el equipo y el receptor.• Conectar el equipo a una toma de corriente en un circuito diferente al que está conectado el receptor.• Solicitar ayuda de un distribuidor o un técnico experimentado en radio/TV.NOTA: Los componentes de la marca de Bluetooth no se utilizarán de ninguna forma o manera que pudiera perjudicar o dañar de otra manera la buena fe vinculada a la marca de Bluetooth o sus miembros asociados (Sky Rich Star Limited). Los componentes de la marca de Bluetooth, por consiguiente, no se utilizarán en relación con productos o servicios que no habiliten funcionalidad inalámbrica alguna, o en relación con actividades ilegales, obscenas, pornográficas, de excesiva violencia, nocivas o de mal gusto por cualquier otro concepto.Hecho en China© 2018 IDC, todos los derechos reservados. La marca Honeywell se usa con licencia de Honeywell lnternational lnc.Honeywell lnternational lnc. no ofrece ninguna Este producto es fabricado para International Development Company.International Development Company899 Henrietta Creek Rd.Roanoke, TX 76262 USAToll-free: 1-877-723-0723ADVERTENCIA ICLe présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Download:
Mirror Download [FCC.gov]
Document ID4050560
Application IDVlg7cLIukFzcPU8rfEThOg==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize76.77kB (959592 bits)
Date Submitted2018-10-27 00:00:00
Date Available2018-10-27 00:00:00
Creation Date2018-10-26 10:28:52
Producing SoftwareAcrobat Distiller 11.0 (Windows)
Document Lastmod2018-10-26 12:27:13
Document TitleBT0445DS0620-IM (E) 2018.8.31
Document CreatorAdobe Illustrator CC (Windows)
Document Author: Administrator
FCC ID Filing: 2AP35BT0445DS

Navigation menu