Delta Systems 2033010 KEY CAPTAIN REMOTE LAUNCHING SYSTEM-TRANSMITTER User Manual

Delta Systems INC. KEY CAPTAIN REMOTE LAUNCHING SYSTEM-TRANSMITTER Catalog mailing

a href="https://usermanual.wiki/Delta-Systems" itemprop="url"> Delta Systems >

USERS MANUAL

Sarasota Quality Products • 27330 Center Ridge Road •Westlake • Ohio 44145 Ph: (440) 899-9820 ● Fx: (440) 899-0930 ● www.sarasotaqp.com 1 PRELIMINARY Key Captain™ Remote Launching System Installation Instructions Sarasota Quality Products is a provider of security/access products for the marine market. Products are designed to secure personal effects and equipment, while providing safety, convenience, and launch assistance for many types of watercraft. PLEASE SAVE THESE INSTRUCTIONS FEATURES: Key Captain™ is a Remote Launching System that provides time saving remote control launch functions for most boats. • Lock & Unlock Compartment Latches • Turn Bilge Blowers On & Off • Trim Down & Up (Trailer Or Storage Position) • Operate Auxiliary Functions (Cabin Lighting, Etc.) • Designed For Easy Installation • Corrosion Resistant Materials Used Throughout • Unique System Sleep Mode • Low Power Saving Operation That Extends Battery Life • Floating Waterproof Remote Transmitter(s) • On Site Programmable Remote Transmitter(s) • Permanently Sealed Control Panel • Audible Sounder Indicates System Operations • FCC Compliant SYSTEM COMPONENTS CONTROL PANEL FLOAT REMOTE TRANSMITTER SELS ELECTRIC LOCK LATCH WARNING: Read and understand these instructions thoroughly before proceeding with installation. Improper installation may result in incorrect operation of the system.  To prevent personal injury, always disconnect the battery leads when installing or servicing this product.  Power source must match the voltage rating of this product.  Always use a fuse with amperage rating specified for this system. Failure to do so may result in serious personal injury or fire hazard. Power Specification (Key Captain™ Control Panel) Circuit Voltage Operating Current Battery (Standby 15MA.) 9 – 16VDC 20 Amp Lock 9 – 16VDC 10 Amp Unlock 9 – 16VDC 10 Amp Trim Up (see note) 9 – 16VDC 5 Amp Trim Down (see note) 9 – 16VDC 5 Amp Bilge Blower (see note) 9 – 16VDC 5 Amp Note: Use BASIC WIRING INSTRUCTIONS except when current requirements exceed fuse ratings shown, then, use ALTERNATE WIRING INSTRUCTIONS. Power Specification (Key Captain™ Electric Lock/Latches) Circuit Voltage Current Lock connection (Lt. Blue) 9 – 16VDC 0.5 Amp Unlock connection (White.) 9 – 16VDC 0.5 Amp Power Specification (Key Captain™ Transmitter) Circuit Voltage Battery # 2 Coin Cell batteries 1.5 VDC ea. CR-2 REQUIRED FOR INSTALLATION • Drill and suitable drill bit • Hole saw • Screwdriver • Wire cutter/striper • Crimp on wire connectors for 12, 16, & 18 gauge wire • Cable tie-wraps • Suitable stainless steel pan head screws • Fuses as required • Fuse holder for above fuses • 12, 16, 18 gauge wire INSTALLATION MUST MEET APPLICABLE SECTIONS OF TITLE 33 CFR 183 SUBPART I, USCG REGULATIONS. To prevent personal injury, always disconnect the battery leads when installing the control panel, electric lock latches or connections to auxiliary function devices. The Key Captain™ control panel is designed for easy installation. See separate installation instructions for mounting of Key Captain™ electrical lock latches. MOUNTING INSTRUCTIONS 1. The Key Captain™ control panel may be positioned near the helm, and in a secure area. The control panel may be secured to any solid, flat mounting surface and oriented in any direction. 2. For security protection, the control panel should be mounted inside a lockable compartment or other secure area. 3. For maximum reception of signals from the transmitter to the control panel it should be located close to top level of the boat (see Fig. 1). It should be mounted within 10 inches of a fuse distribution panel (furnished by others). 4. Using the control panel as a template, mark holes for mounting feet and drill holes. Secure control panel in place taking care not to over tighten screws or penetrate hull. BASIC WIRING INSTRUCTIONS Note: Use BASIC WIRING INSTRUCTIONS except when current requirements exceed fuse ratings shown in Power Specification (Key Captain™ Control Panel), then, use ALTERNATE WIRING INSTRUCTIONS. 1. Connect Key Captain™ control panel wires to fuse distribution box: (Fig 2) 2. Connect control panel negative (green) wire to a good chassis ground or negative post of battery (Fig. 2) 3. Use a quality marine grade stranded copper wire and connect from fuse distribution box to the following circuits: (Fig 2) 4. Connect positive (+) battery (red) control panel circuit from fuse distribution panel to the boat +12VDC battery post (Fig. 2). 5. Connect lock (light blue) control panel circuit wire from fuse distribution panel to SELS 1000 electrical lock latches. Observe polarity of wiring to connect to all light blue wires (Fig. 2) 6. Connect unlock (white) control panel circuit wire from fuse distribution panel to SELS 1000 electrical lock latches. Observe polarity of wiring to connect all white wires together (Fig. 2) 7. Connect trim down (pink) control panel circuit wire from fuse distribution panel to trim down circuit input on trim controller (Fig. 2) 8. Connect trim/trailer up (orange) control panel circuit wire from fuse distribution panel to trim/trailer up circuit input on trim controller (Fig. 2)
Sarasota Quality Products • 27330 Center Ridge Road •Westlake • Ohio 44145 Ph: (440) 899-9820 ● Fx: (440) 899-0930 ● www.sarasotaqp.com 9. Connect bilge blower (brown) control panel circuit wire from fuse distribution panel to +12VDC wire on bilge blower (Fig. 2) 10. Do not make any connection to black wire on the Key Captain™ control panel. This is the antenna wire and it is to hang freely (Fig. 2) OPERATING INSTRUCTIONS Float Remote™ Transmitters control the operation/functions of the Key Captain™ system. The operating range is 25-30 feet with direct line of sight between the transmitter and control panel. The effective range may diminish if direct line of sight is not available. Five function buttons are located on top of the Transmitter. Lock and Un-Lock operations are accomplished by momentarily pressing the following push buttons. Press and release to Lock all electric lock/latches. Press and release to Un-Lock all electric lock/latches. Bilge Blower operations are accomplished by momentarily depressing the following push button. Press and release to turn Bilge Blower ON Press and release again to turn Bilge Blower OFF Trim DOWN and Trim UP operations are accomplished by pressing the following push buttons. 2 Press and hold until desired Trim DOWN position is reached. Press and hold until desired Trim UP (Trailer) position is reached. ALTERNATE WIRING INSTRUCTIONS Note: Use ALTERNATE WIRING INSTRUCTIONS when current requirements exceed fuse ratings shown in Power Specification (Key Captain™ Control Panel). Auxiliary relays are required to switch higher current trim motors and bilge blowers. Auxiliary relays must be rated at 12VDC, 5 amp maximum coils with normally open contacts (de-energized state) that are rated for trim motor and bilge blower current draw. 1. Connect Key Captain™ control panel wires to fuse distribution box: (see Fig 3) 2. Connect control panel negative (green) wire to a good chassis ground or negative post of battery (see Fig. 3) 3. Use a quality marine grade stranded copper wire and connect from fuse distribution box to the following circuits: (see Fig 3) 4. Connect positive (+) battery (red) control panel circuit from fuse distribution panel to the boat +12VDC battery post (see Fig. 3). 5. Connect lock (light blue) control panel circuit wire from fuse distribution panel to Key Captain™ electrical lock latches. Observe polarity of wiring to connect to all light blue wires (see Fig. 3) 6. Connect unlock (white) control panel circuit wire from fuse distribution panel to Key Captain™ electrical lock latches. Observe polarity of wiring to connect all white wires together (see Fig. 3) 7. Connect trim down (pink) control panel circuit wire from fuse distribution panel to coil of an auxiliary relay. Connect other side coil wire to chassis. 8. Connect positive (+) battery to proper sized fuse. Connect from fuse to one side of an auxiliary relay normally open contact. Connect other side of auxiliary relay normally open contact to trim down circuit input on trim controller (see Fig. 3) 9. Connect trim/trailer up (orange) control panel circuit wire from fuse distribution panel to (+) coil of an auxiliary relay. Connect other side coil wire (-) to chassis (see Fig. 3) 10. Connect positive (+) battery to proper sized fuse. Connect from fuse to one side of an auxiliary relay normally open contact. Connect other side of auxiliary relay normally open contact to trim up (trailer) circuit input on trim controller (see Fig. 3) 11. Connect bilge blower (brown) control panel circuit wire from fuse distribution panel to coil (+) of an auxiliary relay. Connect other side coil wire (-) to chassis (see Fig. 3). 12. Connect positive (+) battery to proper sized fuse. Connect from fuse to one side of an auxiliary relay normally open contact. Connect other side of auxiliary relay normally open contact to+12VDC wire on bilge blower (see Fig. 3) 13. Do not make any connection to black wire on the Key Captain™ control panel. This is the antenna wire and it is to hang freely (see Fig. 3) REMOTE FLOAT TRANSMITTER BATTERY REPLACEMENT The Key Captain™, Remote Float™ Transmitter is powered by two coin cell batteries (see Power Specification). To replace the batteries, remove the top off of the unit by prying with small screwdriver. Remove the circuit board. The two batteries are on the under side of the circuit board. Replace batteries. Replace circuit board. Reinstall cap while observing alignment with key clip mounting hole. Used batteries should be disposed of properly. Properly installed the Float Remote™ has a watertight seal and is watertight to IP-67 standards and will float with up to two small boat ignition keys attached to the remote transmitter. Note: The transmitter will not be replaceable under warranty after first customer battery replacement. Pry here to remove the cap from body.
Download:
Mirror Download [FCC.gov]
Document ID640355
Application ID6TV5ivIW0g7u7ymViX5lMw==
Document DescriptionUSERS MANUAL
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize19.51kB (243822 bits)
Date Submitted2006-03-23 00:00:00
Date Available2006-03-22 00:00:00
Creation Date2006-03-21 13:40:11
Producing SoftwareAcrobat Distiller 7.0.5 (Windows)
Document Lastmod2006-03-21 13:41:01
Document TitleCatalog mailing
Document CreatorAcrobat PDFMaker 7.0.7 for Word
Document Author: user
FCC ID Filing: R932033010

Navigation menu