Manual For The 62757 7 In. 1.5 HP Bridge Wet Cut Tile Saw With Stand

User Manual: Manual for the 62757 7 in. 1.5 HP Bridge Wet Cut Tile Saw with Stand 7 in. 1.5 HP Bridge Wet Cut Tile Saw with Stand

Open the PDF directly: View PDF PDF.
Page Count: 20

DownloadManual For The 62757 7 In. 1.5 HP Bridge Wet Cut Tile Saw With Stand
Open PDF In BrowserView PDF
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.

REV 16l

1-1/2 HORSEPOWER

WITH STAND

Visit our website at: http://www.harborfreight.com
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2015 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.

Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

IMPORTANT SAFETY INFORMATION
WARNING indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.

In this manual, on the labeling,
and all other information
provided with this product:
This is the safety alert symbol. It is
used to alert you to potential personal
injury hazards. Obey all safety
messages that follow this symbol
to avoid possible injury or death.

CAUTION, used with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in minor or
moderate injury.
NOTICE is used to address
practices not related to
personal injury.

DANGER indicates a
hazardous situation which, if
not avoided, will result in
death or serious injury.

CAUTION, without the safety
alert symbol, is used to
address practices not related
to personal injury.

General Tool Safety Warnings
RECOMMENDED MINIMUM WIRE
GAUGE FOR EXTENSION CORDS

WARNING Read all safety warnings and
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions
for future reference.
1.

KEEP GUARDS IN PLACE and in working order.

2.

REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.

3.

KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.

4.

DO NOT USE IN DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations, or
expose them to rain. Keep work area well lighted.

5.

KEEP CHILDREN AWAY. All visitors should
be kept safe distance from work area.

6.

MAKE WORKSHOP KID PROOF with padlocks,
master switches, or by removing starter keys.

7.

DO NOT FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.

8.

(120 VOLT)

NAMEPLATE
AMPERES
(at full load)
0–6

18

16

16

14

6.1 – 10

18

16

14

12

10.1 – 12

16

16

14

12

12.1 – 16

14

12

Do not use.

TABLE A
9.

USE PROPER EXTENSION CORD. Make sure
your extension cord is in good condition. When
using an extension cord, be sure to use one heavy
enough to carry the current your product will draw.
An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. Table
A shows the correct size to use depending on
cord length and nameplate ampere rating. If in
doubt, use the next heavier gauge. The smaller
the gauge number, the heavier the cord.

10.

WEAR PROPER APPAREL. Do not wear loose
clothing, gloves, neckties, rings, bracelets, or
other jewelry which may get caught in moving
parts. Nonslip footwear is recommended. Wear
protective hair covering to contain long hair.

11.

ALWAYS USE SAFETY GLASSES. Also use
face or dust mask if cutting operation is dusty.

USE RIGHT TOOL. Don’t force tool or attachment
to do a job for which it was not designed.

Item 62757

EXTENSION CORD
LENGTH
25'
50' 100' 150'

For technical questions, please call 1-888-866-5797.

Page 2

Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.

accessories. The use of improper accessories
may cause risk of injury to persons.

12.

SECURE WORK. Use clamps or a vise to hold
work when practical. It’s safer than using your
hand and it frees both hands to operate tool.

18.

NEVER STAND ON TOOL. Serious injury
could occur if the tool is tipped or if the
cutting tool is unintentionally contacted.

13.

DO NOT OVERREACH. Keep proper
footing and balance at all times.

19.

14.

MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.

15.

DISCONNECT TOOLS before servicing;
when changing accessories, such as
blades, bits, cutters, and the like.

CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that
it will operate properly and perform its intended
function – check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.

16.

REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in
off position before plugging in.

20.

DIRECTION OF FEED. Feed work into
a blade or cutter against the direction of
rotation of the blade or cutter only.

17.

USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended

21.

NEVER LEAVE TOOL RUNNING
UNATTENDED. TURN POWER OFF. Don’t
leave tool until it comes to a complete stop.

Grounding Instructions
TO PREVENT ELECTRIC
SHOCK AND DEATH FROM
INCORRECT GROUNDING
WIRE CONNECTION
READ AND FOLLOW THESE
INSTRUCTIONS:

110-120 VAC Grounded Tools: Tools with Three Prong Plugs
1.

In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.

4.

Check with a qualified electrician or service
personnel if the grounding instructions are
not completely understood, or if in doubt as
to whether the tool is properly grounded.

5.

Use only 3-wire extension cords that
have 3-prong grounding plugs and 3-pole
receptacles that accept the tool’s plug.

2.

Do not modify the plug provided – if it will
not fit the outlet, have the proper outlet
installed by a qualified electrician.

6.

Repair or replace damaged or worn cord immediately.

3.

Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
The conductor with insulation having an outer
surface that is green with or without yellow
stripes is the equipment-grounding conductor. If
repair or replacement of the electric cord or plug
is necessary, do not connect the equipmentgrounding conductor to a live terminal.

Item 62757

Grounding
Pin

125 VAC 3-Prong Plug and Outlet
(for up to 125 VAC and up to 15 A)

For technical questions, please call 1-888-866-5797.

Page 3

7.

This tool is intended for use on a circuit that has
an outlet that looks like the one illustrated above in
125 VAC 3-Prong Plug and Outlet. The tool has
a grounding plug that looks like the plug illustrated
above in 125 VAC 3-Prong Plug and Outlet.

8.

The outlet must be properly installed and grounded
in accordance with all codes and ordinances.

9.

Do not use an adapter to connect
this tool to a different outlet.

110-120 VAC Double Insulated Tools: Tools with Two Prong Plugs
1.

To reduce the risk of electric shock, double
insulated equipment has a polarized plug (one
blade is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.

2.

Double insulated tools may be used in either
of the 120 volt outlets shown in the preceding
illustration. (See Outlets for 2-Prong Plug.)

Outlets for 2-Prong Plug

Tile Saw Safety Warnings
For Your Own Safety Read Instruction
Manual Before Operating Saw

f. Spreader – A metal plate that follows the saw blade
to keep the kerf (gap) from closing on the saw blade.
Spreaders, except riving knives, must be aligned to
the blade after blade adjustment to prevent binding.

1.

Wear eye protection.

2.

Use saw-blade guard and spreader
for every operation for which it can be
used, including all through sawing.

3.

Keep hands out of the line of saw blade.

4.

Know how to reduce risk of kickback.

As noted previously, Kickback is a sudden reaction
to a pinched, bound, or misaligned blade, causing an
uncontrolled workpiece to lift up and out of the saw
toward the operator.
Kickback is usually a result of tool misuse and can be
limited or avoided by following the precautions below:

5.

Do not perform any operation freehand.

• Fence must be completely
parallel to the saw blade.

6.

Never reach around or over saw blade.

7.

Make sure the workpiece is supported
at all times while sawing.

8.

To properly understand all safety
warnings, be familiar with the following
safety terms and equipment:

9.

• Workpiece must be free from flaws
and from foreign objects.
• Do not use a dull or damaged blade.
• Maintain control of the workpiece. Do not
allow the workpiece to rest against the
moving blade without holding onto it.
• If the blade binds or a cut is interrupted, turn
off the power switch and hold the workpiece
still until the blade stops. Correct the cause
of blade binding before proceeding.

a. Featherboard – A block with “fingers” that hold
the workpiece against the fence while sawing.
b. Through-sawing – A cut made from one side of
a tile to the opposite side, without stopping.
c. Freehand – Feeding a workpiece through the
saw without using a fence or guided support
to guide it. NOT A SAFE METHOD.

• Before continuing an unfinished cut,
center the blade in the pre-cut kerf and
check that the saw is not engaged into the
workpiece before turning on the saw.

d. Kerf – The gap made by the saw in the workpiece.

• Push the tile past the blade prior to release.

e. Kickback – A sudden reaction to a pinched,
bound, or misaligned blade, causing an
uncontrolled workpiece to lift up and out
of the saw toward the operator.

Item 62757

10.

Check guards for proper operation with saw
disconnected from power before each use.
Do not disable any guard. Do not operate
saw if any movable guard does not move

For technical questions, please call 1-888-866-5797.

Page 4

freely and close instantly. Make sure any
movable guard does not touch the blade in
all angles, depths of cut, and positions.
11.

Keep the guard in place while throughsawing. Verify that the spreader lines up
with the blade to prevent binding.

3.

Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s)
to be used for the tile saw. Receptacles are
available having built-in GFCI protection and
may be used for this measure of safety.

4.

DO NOT OPERATE WITH ANY GUARD DISABLED,
DAMAGED, OR REMOVED. Moving guards
must move freely and close instantly.

5.

The use of accessories or attachments not
recommended by the manufacturer may
result in a risk of injury to persons.

6.

When servicing use only identical replacement parts.

7.

Only use safety equipment that has been approved
by an appropriate standards agency. Unapproved
safety equipment may not provide adequate
protection. Eye protection must be ANSI-approved
and breathing protection must be NIOSH-approved
for the specific hazards in the work area.

8.

Industrial applications must follow OSHA guidelines.

9.

Maintain labels and nameplates on
the tool. These carry important safety
information. If unreadable or missing, contact
Harbor Freight Tools for a replacement.

10.

Avoid unintentional starting. Prepare to
begin work before turning on the tool.

11.

People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.

12.

WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities, contains chemicals known to the State
of California to cause cancer and birth defects or
other reproductive harm. Some examples of these
chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or other
masonry products
• Arsenic and chromium from chemically
treated lumber
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)

13.

WARNING: The cord of this product contains lead
and/or di (2-ethylhexyl) phthalate (DEHP), chemicals
known to the State of California to cause cancer, and
birth defects or other reproductive harm. Wash hands

POSITION OF TILE SAW

1.

2.

To avoid the possibility of the tool plug or
receptacle getting wet, position tile saw to one
side of a wall mounted receptacle to prevent
water from dripping onto the receptacle or plug.
The user should arrange a “drip loop” in the cord
connecting the saw to a receptacle. The “drip
loop” is that part of the cord below the level of
the receptacle, or the connector if an extension
cord is used, to prevent water traveling along the
cord and coming in contact with the receptacle.
If the plug or receptacle does get wet, DON’T unplug
the cord. Disconnect the fuse or circuit breaker
that supplies power to the tool. Then unplug and
examine for presence of water in the receptacle.

EXTENSION CORDS
1.

2.

Use only extension cords that are intended for
outdoor use. These extension cords are identified
by a marking “Acceptable for use with outdoor
tools; store indoors while not in use.” Use only
extension cords having an electrical rating not
less than the rating of the product. Do not use
damaged extension cords. Examine extension
cord before using and replace if damaged. Do
not abuse extension cords and do not yank
on any cord to disconnect. Keep cord away
from heat and sharp edges. Always disconnect
the extension cord from the receptacle before
disconnecting the product from the extension cord.
WARNING – To reduce the risk of electrocution,
keep all connections dry and off the ground.
Do not touch plug with wet hands.

Item 62757

For technical questions, please call 1-888-866-5797.

Page 5

after handling. (California Health & Safety Code
§ 25249.5, et seq.)
14.

WARNING: This product contains di (2-ethylhexyl)
phthalate (DEHP), a chemical known to the State of
California to cause cancer and birth defects or other
reproductive harm. (California Health & Safety Code
§ 25249.5, et seq.)

15.

The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.

Item 62757

For technical questions, please call 1-888-866-5797.

Page 6

Vibration Safety
This tool vibrates during use. Repeated or
long-term exposure to vibration may cause
temporary or permanent physical injury,
particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:
1.

Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical checkups to ensure medical problems are not being
caused or worsened from use. Pregnant women
or people who have impaired blood circulation
to the hand, past hand injuries, nervous system
disorders, diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical or
physical symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.

2.

Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.

3.

Wear suitable gloves to reduce the
vibration effects on the user.

4.

Use tools with the lowest vibration when there
is a choice between different processes.

5.

Include vibration-free periods each day of work.

6.

Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.

7.

To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.

SAVE THESE
INSTRUCTIONS.

Item 62757

For technical questions, please call 1-888-866-5797.

Page 7

Specifications
Electrical
Requirements

120 VAC / 60 Hz / 9.2 A

Saw Bevel Capacity

Motor Speed

3550 RPM

Rip Fence Scale

Blade Diameter
(Diamond Blade
Sold Separately)
Maximum Cutting
Capacity

7" Diameter / Continuous
Rim Blade Rated at 3550
RPM or Greater
1" @ 45°
1" @ 90°
Floor and Wall Tiles:
24" x 24"
Marble and Brick:
25" long

Maximum Tile Size

0° to 45° in 2.5° Increments
- Left Tilt Only
0" to 8-1/4" in 1/8"
Increments

Arbor Size

5/8"

Accessories

Two Arbor Nut Wrenches

Switch

Waterproof On/Off Switch

268700

Assembly
Note: For additional information regarding the
parts listed in the following pages, refer to the
Assembly Diagram near the end of the manual.
WARNING! Always make sure the Power Switch
of the Tile Saw is in its “OFF” position and the unit is
unplugged from the electrical outlet prior to assembly,
adding accessories, or making adjustments to the
unit. Be sure to wear heavy-duty work gloves when
making any kind of adjustments to the unit.
1.

Unpack the Tile Saw, and with assistance, carefully
lay the tool on its side on a flat, level floor surface.

2.

Pull out Stand I (119) and Stand II (120), fully
extending the Support Brackets (117, 118).
(See Figure A.)

Item 62757

(117,118)
(120)

(119)
Figure A
3.

With assistance, set the Tile Saw
upright. (See Figure B.)

For technical questions, please call 1-888-866-5797.

Page 8

4.

The Adjusting Knob (123) is located at the bottom of
Stand II (120). Turn the Adjusting Knob clockwise
or counterclockwise to keep the Tile Saw stand
balanced evenly on the floor. (See Figure B.)

5.

Attach the Handle (4) to the Motor Support (25),
using the Bolts (1), Spring Washers (2),
and Washers (3). (See Figure C.)

(4)
(120)

(1)
(2)
(123)

(25)

(3)
Figure C

Figure B

Attaching Knobs
(111)

(75)

Figure D
6.

Align the Right Rail Stand (111) (See Figure D.)

7.

Remove the shipping screw and attach the
Knob (75) through the slot in the Right Rail
Stand (111) and into the threaded hole as shown.

8.

Repeat for the Left Rail Stand (72)
and the other Knob (75).

9.

Secure Knobs.

Item 62757

For technical questions, please call 1-888-866-5797.

Page 9

Wheel Assembly
1.

The Wheels (54) are connected to
Stand I (119) using Bolts (57), Hex Nuts (67)
and Washers (3). (See Figures E-I)

2.

Lift the saw stand with the front handle
to move it, as shown in Figure I.

Bolts (57)
(3)

(3)

Hex Nuts
(67)
(54)
Figure E

Figure H

(120)

Figure F
(59)

Figure I

Figure G
Note: Bolts should be inserted from outside, through
the leg stand and into the wheel. Washers and Nuts
to be placed onto the Bolts from the wheel side.

Item 62757

For technical questions, please call 1-888-866-5797.

Page 10

Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including
all text under subheadings therein before set up or use of this product.

Tool Set Up
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power
Switch of the tool to its “OFF” position and unplug the tool from its electrical outlet
before performing any inspection, maintenance, or cleaning procedures.
Note: The Right Rail Stand (111) is held in place by
the packaging during shipment. Always tighten the
T-Knob (107) to lock the Rail Stand prior to performing
maintenance or relocating the Tile Saw. (See Figure J.)

(107)
(111)

To Fill And Drain The Water Tray:
1.

Fill Water Tray (60) with enough clean, cold
water to submerge 3/4 of the Water Pump. Do
not overflow the Water Tray. (See Figure K.)

Note: To prevent excessive wear on the Saw Blade,
make sure to maintain a continuous flow of water
over the entire Saw Blade while cutting. Never cut
anything if the water flow is not continuous.
2.

Prior to draining the Water Tray (60) first place a
large bucket under the Drain Plug (62). Remove the
Drain Plug located at the bottom of the Water Tray.
Once drained, replace the Drain Plug. You may also
pull out the Water Tray from the Tile Saw and pour
out the water. (See Figure K.)

3.

After draining the water, rinse Water
Tray to remove any silt.

Figure J

(62)

(60)
Figure K

Item 62757

For technical questions, please call 1-888-866-5797.

Page 11

To Make A Straight Cut:
WARNING! Use safety equipment. Always wear
eye protection. Wear ANSI approved safety glasses
under an ANSI approved full face safety shield
and non-skid safety shoes. Hearing and breathing
protection must be used for appropriate conditions.

(17)

Positioning the Tile
1.

Loosen the T-Knob (107) on the Angle Cutting
Guide (102) and position at 90 degrees on the Scale
Rail (105). Then, retighten the T-Knob.
(See Figure L.)

2.

To Adjust the gap between the Angle Cutting
Guide (102) and the cutting slot in the Table (87),
loosen the Butterfly Knob (103) on the Scale
Rail (105). Move the Scale Rail to the desired
position. Then, retighten the Butterfly Knob on the
Scale Rail.
(See Figure L.)

3.

Position the tile against the Scale Rail (105) and
Angle Cutting Guide (102).
(See Figure L.)

4.

Check to make sure the water level in the Water
Tray (60) is at the proper level (the Water Pump (51)
should be about 3/4 submerged). Then slide in
the Water Tray completely. (See Figure K.)

5.

Plug the Power Cable (7) into the nearest 120
volt, grounded, electrical outlet, making sure
to form a “drip loop” with the Power Cord. See
“POSITION OF TILE SAW” on page 5.
(87)

(18)

Figure M
7.

Hold the tile firmly against the Angle Cutting
Guide (102) and Scale Rail (105) with one
hand. Always keep fingers a safe distance away
from the Saw Blade (37). With the other hand,
hold the Handle (4) and slowly move the Saw
Blade forward over the tile. (See Figure N.)

8.

Continue moving the Saw Blade (37) over the tile
until the cut is completed.
(See Figure N.)

9.

Once the cut is completed, turn the Power
Switch (37) to its “OFF” position and allow
the Saw Blade to stop on its own. Unplug
the Power Cord from its electrical outlet.
Then, remove the cut tile and debris from the
Table (87). (See Figure M and Figure N.)

Note: If the Motor of the Tile Saw stops suddenly while
cutting, turn the Power Switch (18) to its “OFF” position.
Wait approximately 5 minutes. While making sure your
hands are dry, reset the Circuit Breaker by pushing in the
button. Then, turn the Power Switch to its “ON” position to
resume cutting. (See Figure M.)

(105)

Handle (4)
Saw
Blade
(37)
(103)

(102)

Figure L
6.

Tile

Turn the Power Switch (18) to its “ON”
position, and allow the Saw Blade (37) to
spin up to full speed. (See Figure M.)
Figure N

Item 62757

For technical questions, please call 1-888-866-5797.

Page 12

Note: If the Pump fails, first try clearing the Filter of
debris and make sure it is not plugged. If Pump still
does not operate properly, it must be replaced.
To Make A Miter Cut:
1.

Loosen the Butterfly Knob (103) on the Angle Cutting
Guide (102) and position the Angle Cutting Guide
at the desired angle to the Scale Rail (105). Then,
retighten the Butterfly Knob (103). (See Figure O.)

2.

For a 45 degree cut, use the 45° Angle Cutting
Guide (102) that is included as an accessory item.
Hold the tile against the Guide and slide the Guide
down the Scale Rail (105). (See Figure O.)

3.

To cut the tile, follow the same procedure
as outlined in the section “To Make
A Straight Cut:” on page 12.

(75)

(75)

(105)
Figure P

(103)
Figure O

(102)

To Make A Bevel Cut;
1.

Loosen the Knob (75) on each end of the Tile
Saw. Also loosen 2 Bolts, (located on lower
end of each Rail Stand (72 & 111). Tilt the
Slide Rail (84) to the desired angle as indicated
on the Angle Scale (110). Then, retighten the
two Knobs, and two bolts. (See Figure P.)

2.

To cut the tile, follow the same procedure
as outlined in the section “To Make
A Straight Cut:” on page 12.

Item 62757

For technical questions, please call 1-888-866-5797.

Page 13

To Change The Saw Blade:

(41)

WARNING! Make sure the Power Switch (37) of the Tile
Saw is in its “OFF” position and that the unit is unplugged
from its electrical outlet before performing this procedure.
1.

(39)

Remove the Screws (47) from the Blade
Guard (41). (See Figure Q.)

(37)
(38)

(41)
(47)

Figure R

(47)

(37)

Figure Q
2.

Carefully lift up and move the Blade Guard (41) away
from the catch on the top end of the motor support to
expose the Saw Blade.
(See Figure R.)

3.

CAUTION! Wear heavy-duty work
gloves to avoid cuts to hands.

4.

With one of the provided Wrenches, hold the end of
the Motor Spindle firmly and with the other Wrench,
unscrew and remove the Nut (39) by turning it
clockwise. Next, remove the Outside Flange (38) and
remove the old Saw Blade. (See Figures R and S.)

Item 62757

(32)
Figure S
5.

Install a new Saw Blade (not included). Always
use Continuous Rim Diamond Saw Blades
rated at 3550 RPM or higher. (See Figure R.)
CAUTION! Never flip over a used Saw Blade.

For technical questions, please call 1-888-866-5797.

Page 14

6.

IMPORTANT: When installing a Saw Blade (37),
make sure the “ARROW” depicted on the side of the
Saw Blade points in the same direction as that of the
Blade Guard (41).
(See Figure T.)

8.

Carefully lower Blade Guard (41) back into its
original position. Then secure Blade Guard in
place using the Bolts (47). (See Figure U.)
(47)

(47)

(37)

Figure U

(41)

Figure T
7.

Once the Saw Blade (37) is installed, reattach
the Outside Flange (38) and Nut (39). Fasten
the Nut by turning it counterclockwise until
snug. Do not overtighten. (See Figure R.)

Item 62757

For technical questions, please call 1-888-866-5797.

Page 15

Maintenance And Servicing
Procedures not specifically explained in this manual must be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool to its “OFF” position and unplug the tool from its
electrical outlet before performing any inspection, maintenance, or cleaning procedures.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication
1.

2.

WARNING! Make sure the Power Switch (18)
of Tile Saw is in its “OFF” position and that unit
is unplugged from its electrical outlet before
performing any inspection, maintenance, or cleaning
procedures. Any service not listed below should
only be performed by a qualified technician.

6.

Before each use, inspect the general condition of
the Tile Saw. Check for loose screws, misalignment
or binding of moving parts, damaged electrical
wiring, damaged Hoses, and any other condition that
may affect its safe operation. If abnormal noise or
vibration occurs, have the problem corrected before
further use. Do not use damaged equipment.

If water delivery volume is reduced, clean the Filter
and the Impeller. If no water is being delivered
or is still restricted, the Delivery Tube or Nozzle
maybe blocked. If the Pump does not buzz or
deliver any water, even when Delivery Tube is
disconnected, the Pump may need to be replaced.

7.

To replace the Water Pump (51), disconnect the
Power Supply Cord and remove the Water Tray (60).
Locate the Pump Plug Cover (65) on the inner left
side of the Frame. Unscrew and remove the Wing
Nut (64) from the Pump Plug Cover. Remove the
Pump Plug Cover to expose the Pump Cable (52).
Disconnect the Pump Cable from the Water Pump.
Next, disconnect the Pump Connector from the Water
Pump. Then, remove the old Water Pump. Install the
new Water Pump, following the previously mentioned
Steps in reverse order. (See Assy. Diagram.)

8.

To clean the exterior parts: Use only a clean cloth
and mild detergent to clean the body of the Tile
Saw. Use a wet/dry vacuum cleaner or compressed
air to clean the Motor (22) ventilation slots. Do not
immerse any electrical part of the tool in liquid.

9.

Empty all water from Saw before storing. Ice
crystals will damage the Pump if the unit contains
water in freezing temperatures. Store the
Tile Saw indoors in a dry, frost-free room.

3.

Before each use, inspect the Saw Blade (37). Using
a dull Saw Blade will cause excessive wear on
the Motor, and will not produce a satisfactory cut.
Replace with a new Saw Blade when needed.

4.

Before each use, inspect mounting Screws on all
Safety Covers and the Arbor Nut (40) on the Motor
Arbor. If necessary, retighten loose hardware.

5.

After each use, immediately clean the Water
Pump (51) to keep dried debris from sticking to
the Filter and Impeller which will obstruct the water
flow. To clean the Water Pump, remove the Outer
Cover. Remove the Filter. Then, remove the
Inner Cover to expose the Impeller. Use a small
brush and clean water to remove any debris on
the Filter and Impeller. If necessary, replace the

Item 62757

old Filter. When finished, replace the Inner Cover,
Filter, and Outer Cover. (See Assy. Diagram.)

For technical questions, please call 1-888-866-5797.

Page 16

Troubleshooting
Problem

Possible Causes

1.
Tool will not start
2.
1.
Blade spins slowly
2.
Excessive vibration 1.
2.
Running hot;
1.
excess smoke
2.
3.

No power at outlet.
Cord not connected.
Arbor shaft binding
Motor brushes worn
Bent or off-balance blade
Bent Arbor Shaft

1.
2.
1.
2.
1.
2.
1.
Not enough water
2.
Running with hot/warm water 3.

Likely Solutions
Check power at outlet.
Check that cord is plugged in.
Check shaft for free spinning
Replace brushes
Replace blade with new one
Check shaft for run-out
Check connection
Always run with cold water

Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect
power supply before service.

PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here:
Note:

If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and are not available individually
as replacement parts.

Item 62757

For technical questions, please call 1-888-866-5797.

Page 17

PARTS LIST
Part
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62

Description
Bolt, M6x30
Elastic Washer
Flat Washer
Handle
Insert
Handle Sleeve
Power Cable
Strain Relief
Capacitor
Capacitor Clamp Plate
Screw
Screw
Upper Cover For Switch Box
Sealing Pad
Screw M4x10
Flat Washer
Circuit Breaker
Power Switch
Rubber Ring For Cable
Screw M5x14
Flat Washer
Motor
Lower Cover For Switch Box
Rubber Pad
Motor Support
Screw M4x8
Elastic Washer
Earth Terminal
Teeth Washer
Rubber Ring
Buffer Pad
Inside Flange
Clamp
Cable Fixing Plate
Screw M4x16
Elastic Washer
Saw Blade (Sold Separately)
Outside Flange
Nut
Arbor Nut
Blade Guard
Wing Nut
Fixing Plate
Water Hose Adpator
Rubber Curtain
Bolt M6x12
Screw M4x40
Water Hose
Tri-Way Adaptor
Water Hose
Water Pump
Water Pump Cable
Bolt M12x60
Wheel
Wheel Bracket
Leg Pad
Bolt M6x45
Flat Washer
Lock Nut
Water Tray
O-Shape Sealing Ring
Drain Plug

Item 62757

Qty
2
6
22
1
1
1
1
2
1
1
6
3
1
1
8
6
1
1
1
7
11
1
1
1
1
2
6
2
2
1
1
1
2
2
2
6
1
1
1
2
1
1
1
2
1
1
2
1
1
1
1
1
2
2
2
3
4
4
2
1
1
1

Part
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124

Description
Insert For Drain Plug
Wing Nut
Pump Plug Cover
Bolt M6x40
Lock Nut
Carrying Handle
Carrying Handle Sleeve
Tension Adjusting Bracket
Screw M6x12
Left Rail Stand
Bolt M6x16
Angle Scale (B)
Knob
Screw M6x25
Elastic Washer
Flat Washer
Bolt M6x90
Locking Washer
Ball Bearing Holder
Buffer Pad
Supporting Plate (B)
Slide Rail
Bolt M6x20
Rubber Pad For Work Table
Table
Protection Hose Adaptor
Rubber Washer
Nut
Protection Hose
Work Table (B)
Work Table ( C )
Scale Plate (B)
Scale Plate (A)
Miter Gauge Holder
Screw M4x20
Coach Bolt M4x20
Pressing Plate
Miter Gauge Bracket
Angle Scale ( C )
Angle Cutting Guide
Big Flat Washer
Scale Rail
End Insert For Work Table
T-Knob
Insert Pad
Angle Pointer
Angle Scale (A)
Right Rail Stand
Supporting Plate (A)
Elastic Pin
Wing Nut
Machine Frame
Insert (B)
Support Bracket
Support Bracket
Support Stand I
Support Stand Ii
Height Adjustable Leg
Elastic Pin
Adjusting Knob
Adjusting Plate

For technical questions, please call 1-888-866-5797.

Qty
1
1
1
4
9
2
2
1
8
1
2
1
2
8
12
12
1
1
1
1
1
1
4
1
1
1
1
1
1
3
3
1
1
1
9
4
4
1
1
1
2
2
1
7
1
2
1
1
1
1
4
4
1
5
2
2
1
1
1
1
1
1

Page 18

ASSEMBLY DIAGRAM

Please Note: Saw Blade (37) is sold separately
and not included.

Item 62757

For technical questions, please call 1-888-866-5797.

Page 19

Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability
standards, and warrants to the original purchaser that this product is free from defects in materials
and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to
damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside
our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We
shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special
or consequential damages arising from the use of our product. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply
to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to
state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 20
Producer                        : Mac OS X 10.9.5 Quartz PDFContext
Create Date                     : 2016:12:21 18:20:27Z
Modify Date                     : 2016:12:21 18:20:27Z
EXIF Metadata provided by EXIF.tools

Navigation menu