767sec9_revH PS 767

User Manual: PS-767

Open the PDF directly: View PDF .
Page Count: 272 [warning: Documents this large are best viewed by clicking the View PDF Link!]

767-200/300/400ER

D6-58328 SEPTEMBER 2005 i

767

Airplane Characteristics for

Airport Planning

Boeing Commercial Airplanes

D6-58328

ii MAY 2011

767 AIRPLANE CHARACTERISTICS FOR AIRPORT PLANNING

LIST OF ACTIVE PAGES

Page Date Page Date Page Date

Original

1 to 90

Preliminary

April 1979

182 June 2010

214-219 June 2010

Rev A

1 to 96

Preliminary

July 1980

3 May 2011

Rev B

1 to 106 July 1981

Rev C

1 to 106 April 1983

Rev D

1 to 126 December 1983

Rev E

1 to 204 January 1986

Rev F

1 to 176 February 1989

Rev G

1 to 200 December 2003

Rev H September 2005

1 to 268 All Pages

D6-58328 SEPTEMBER 2005 iii

TABLE OF CONTENTS

SECTION TITLE PAGE

1.0 SCOPE AND INTRODUCTION 1

1.1 Scope 2

1.2 Introduction 3

1.3 A Brief Description of the 767 Family of Airplanes 4

2.0 AIRPLANE DESCRIPTION 7

2.1 General Characteristics 8

2.2 General Dimensions 15

2.3 Ground Clearances 19

2.4 Interior Arrangements 23

2.5 Cabin Cross-Sections 30

2.6 Lower Cargo Compartments 32

2.7 Door Clearances 37

3.0 AIRPLANE PERFORMANCE 45

3.1 General Information 46

3.2 Payload/Range for Long-Range Cruise 47

3.3 F.A.R. Takeoff Runway Length Requirements 57

3.4 F.A.R. Landing Runway Length Requirements 93

4.0 GROUND MANEUVERING 103

4.1 General Information 104

4.2 Turning Radii 105

4.3 Clearance Radii 108

4.4 Visibility from Cockpit in Static Position 109

4.5 Runway and Taxiway Turn Paths 110

4.6 Runway Holding Bay 115

5.0 TERMINAL SERVICING 117

5.1 Airplane Servicing Arrangement - Typical Turnaround 118

5.2 Terminal Operations - Turnaround Station 123

5.3 Terminal Operations - En Route Station 129

5.4 Ground Servicing Connections 132

5.5 Engine Start Pneumatic Requirements - Sea Level 139

5.6 Ground Pneumatic Power Requirements 144

5.7 Conditioned Air Flow Requirements 147

5.8 Ground Towing Requirements 151

D6-58328

iv SEPTEMBER 2005

TABLE OF CONTENTS (CONTINUED)

SECTION TITLE PAGE

6.0 JET ENGINE WAKE AND NOISE DATA 153

6.1 Jet Engine Exhaust Velocities and Temperatures 154

6.2 Airport and Community Noise 177

7.0 PAVEMENT DATA 181

7.1 General Information 182

7.2 Landing Gear Footprint 185

7.3 Maximum Pavement Loads 188

7.4 Landing Gear Loading on Pavement 191

7.5 Flexible Pavement Requirements - U.S. Army Corps of

Engineers Method (S-77-1) 198

7.6 Flexible Pavement Requirements - LCN Method 201

7.7 Rigid Pavement Requirements -

Portland Cement Association Design Method 204

7.8 Rigid Pavement Requirements - LCN Conversion 207

7.9 Rigid Pavement Requirements - FAA Method 211

7.10 ACN/PCN Reporting System: Flexible and Rigid Pavements 214

8.0 FUTURE 767 DERIVATIVE AIRPLANES 225

9.0 SCALED 767 DRAWINGS 227

D6-58328 SEPTEMBER 2005 1

1.0 SCOPE AND INTRODUCTION

1.1 Scope

1.2 Introduction

1.3 A Brief Description of the 767 Family of Airplanes

D6-58328

2 SEPTEMBER 2005

1.0 SCOPE AND INTRODUCTION

1.1 Scope

This document provides, in a standardized format, airplane characteristics data for general airport

planning. Since operational practices vary among airlines, specific data should be coordinated with

the using airlines prior to facility design. Boeing Commercial Airplanes should be contacted for any

additional information required.

Content of the document reflects the results of a coordinated effort by representatives from the

following organizations:

l Aerospace Industries Association

l Airports Council International - North America

l Air Transport Association of America

l International Air Transport Association

The airport planner may also want to consider the information presented in the "Commercial Aircraft

Design Characteristics – Trends and Growth Projections," available from the US AIA, 1250 Eye St.,

Washington DC 20005, for long-range planning needs. This document is updated periodically and

represents the coordinated efforts of the following organizations regarding future aircraft growth

trends:

l International Coordinating Council of Aerospace Industries Associations

l Airports Council International - North American and World Organizations

l Air Transport Association of America

l International Air Transport Association

D6-58328 MAY 2011 3

1.2 Introduction

This document conforms to NAS 3601. It provides characteristics of the Boeing Model 767 airplane

for airport planners and operators, airlines, architectural and engineering consultant organizations,

and other interested industry agencies. Airplane changes and available options may alter model

characteristics; the data presented herein reflect typical airplanes in each model category.

For additional information contact:

Boeing Commercial Airplanes

P.O. Box 3707

Seattle, Washington 98124-2207

U.S.A.

Attention: Manager, Airport Technology

Mail Code 20-93

D6-58328

4 SEPTEMBER 2005

1.3 A Brief Description of the 767 Family of Airplanes

The 767 is a twin-engine family of airplanes designed for medium to long range flights. It is powered

by advanced high bypass ratio engines. Characteristics unique to the 767 include:

l Advanced aerodynamics

l Stronger and lighter materials

l Two-crew cockpit with digital flight deck systems

l High bypass ratio engines

l Twin-aisle seating

l Extended range operations

767-200, -200ER

The 767-200 can carry up to 216 passengers and baggage over 3,900 nautical miles. The 767-200ER,

with the center fuel tanks can also carry 216 passengers and baggage on routes over 5,200 nautical

miles. Seating arrangement varies with airline option. Both airplane models have identical outside

dimensions.

767-300, -300ER

The 767-300 and -300ER are 21 feet 1 inch longer than the 767-200. The additional length enables

the airplane to carry more passengers. The -300ER is also fitted with center fuel tanks for additional

range. Except for the longer fuselage, the -300 and the -300ER have dimensions identical to the

-200 and -200ER.

The -300 and -300ER can be fitted with an optional mid-cabin door to facilitate loading and unloading

of passengers. This arrangement also allows alternate passenger accommodations, up to and

including maximum passenger capacity (exit limit).

767-300 Freighter

The 767-300 Freighter is equipped with a main deck cargo door that enables it to load cargo

containers and/or pallets on the main deck. The main deck can accommodate either a manual cargo

handling system or a powered transfer system (General Market Freighter). The 767-300 Freighter

does not have windows and doors, except for the left entry door for crew access.

D6-58328 SEPTEMBER 2005 5

767-400ER

The 767-400ER is 21 feet longer than the 767-300. The -400ER is equipped with a new-generation

wing design and new engines to enable it to achieve long range operations along with the additional

payload.

Military Derivatives

The 767-200 airplane is also delivered for military uses. These derivatives are not mentioned in this

document because they are equipped with special equipment used for special missions. Some of the

external dimensions may be similar to the standard 767-200 airplane such that some of the data in this

document can be used.

Extended Range Operations (ETOPS)

The 767 can be equipped with special features to enable it to fly extended range operations in remote

areas. This feature is standard on the 767-400ER.

767 Engines

The 767 is offered with a variety of engines. These engines are high bypass ratio engines which are

more economical to maintain and are more efficient. See Table 1.3.1 for engine applicability.

Cargo Handling

The lower lobe cargo compartments can accommodate a variety of containers and pallets now used

in narrow-body and wide-body airplanes. The optional large forward cargo door (standard on the

767-200ER, 767-300ER, 767-300 Freighter, and 767-400ER) allow loading of 96- by 125-in (2.44 by

3.18 m) pallets and also split-engine carriage kits. In addition, bulk cargo is loaded in the aft cargo

compartment and the forward cargo compartment where space permits.

Ground Servicing

The 767 has ground service connections compatible with existing ground service equipment, and no

special equipment is necessary.

Document Applicability

This document contains data pertinent to all 767 airplane models (767-200/200ER/300/300ER/300

Freighter/400ER).

D6-58328

6 SEPTEMBER 2005

MAXIMUM DESIGN TAXI WEIGHT – 1,000 LB (1,000 KG)

ENGINE

MODEL

(2 EACH)

RATED

SLST

THRUST

PER

ENGINE

767-200 767-200ER 767-300 767-300ER 767-300

FREIGHTER 767-400ER

JT9D-7R4D

48,000 LB

(21,772 KG)

CF6-80A 48,000 LB

(21,772 KG)

JT9D-7R4E

50,000 LB

(22,680 KG)

CF6-80A2 50,000 LB

(22,680 KG)

284.0 (128.8)

302.0 (137.0)

312.0 (141.5)

317.0 (143.8)

337.0 (152.9)

347.0 (157.4)

352.2 (159.8)

PW4052 50,200 LB

(22,770 KG)

CF6-80C2-B2 52,500 LB

(23,814 KG)

302.0 (137.0)

312.0 (141.5)

317.0 (143.8)

347.0 (157.4)

352.0 (159.7)

NOT

AVAILABLE

NOT

AVAILABLE

CF6-80C2-B4 57,900 LB

(26,263 KG)

PW4056 56,750 LB

(25,741 KG)

337.0 (152.9)

347.0 (157.4)

352.2 (159.8)

381.0 (172.8)

388.0 (176.0)

396.0 (179.6)

PW4060 60,000 LB

(27,216 KG)

CF6-80C2-B6 61,500 LB

(27,896 KG)

NOT

AVAILABLE

RB211-524G 58,000 LB

(26,308 KG)

NOT

AVAILABLE

RB211-524H 60,600 LB

(27,488 KG)

337.0 (152.9)

347.0 (157.4)

352.2 (159.8)

381.0 (172.8)

388.0 (176.0)

396.0 (179.6)

347.0 (157.4)

352.0 (159.7)

NOT

AVAILABLE

CF6-80C2-

B8F 60,600 LB

(27,488 KG)

CF6-80C2-

B7F1 60,600 LB

(27,488 KG)

PW4062 60,600 LB

(27,488 KG)

NOT

AVAILABLE

NOT

AVAILABLE

NOT

AVAILABLE

381.0 (172.8)

388.0 (176.0)

401.0 (181.9)

409.0 (185.5)

413.0 (187.3)

381.0 (172.8)

388.0 (176.0)

401.0 (181.9)

409.0 (185.5)

413.0 (187.3)

451.0 (204.6)

NOTES:

1. ENGINE/TAXI WEIGHT COMBINATIONS SHOWN ARE AS DELIVERED OR AS OFFERRED BY BOEING

COMMERCIAL AIRPLANES. CERTAIN ENGINES MAY NOT YET BE CERTIFICATED.

2. CONSULT WITH USING AIRLINE FOR ACTUAL OR PLANNED ENGINE/WEIGHT COMBINATION.

3. SEE SECTION 2.1 GENERAL CHARACTERISTICS FOR DETAILS ON SELECTED AIRPLANES.

1.3.1 BRIEF DESCRIPTION – ENGINE/WEIGHT COMBINATIONS

MODEL 767

D6-58328 SEPTEMBER 2005 7

2.0 AIRPLANE DESCRIPTION

2.1 General Characteristics

2.2 General Dimensions

2.3 Ground Clearances

2.4 Interior Arrangements

2.5 Cabin Cross Sections

2.6 Lower Cargo Compartments

2.7 Door Clearances

D6-58328

8 SEPTEMBER 2005

2.0 AIRPLANE DESCRIPTION

2.1 General Characteristics

Maximum Design Taxi Weight (MTW). Maximum weight for ground maneuver as limited by aircraft

strength and airworthiness requirements. (It includes weight of taxi and run-up fuel.)

Maximum Design Takeoff Weight (MTOW). Maximum weight for takeoff as limited by aircraft

strength and airworthiness requirements. (This is the maximum weight at start of the takeoff run.)

Maximum Design Landing Weight (MLW). Maximum weight for landing as limited by aircraft

strength and airworthiness requirements.

Maximum Design Zero Fuel Weight (MZFW). Maximum weight allowed before usable fuel and

other specified usable agents must be loaded in defined sections of the aircraft as limited by strength

and airworthiness requirements.

Spec Operating Empty Weight (OEW). Weight of structure, powerplant, furnishing systems,

unusable fuel and other unusable propulsion agents, and other items of equipment that are considered

an integral part of a particular airplane configuration. Also included are certain standard items,

personnel, equipment, and supplies necessary for full operations, excluding usable fuel and payload.

Maximum Structural Payload. Maximum design zero fuel weight minus operational empty weight.

Maximum Seating Capacity. The maximum number of passengers specifically certificated or

anticipated for certification.

Maximum Cargo Volume. The maximum space available for cargo.

Usable Fuel. Fuel available for aircraft propulsion.

D6-58328 FEBRUARY 2006 9

CHARACTERISTICS UNITS MODEL 767-200 (1)

POUNDS 284,000 302,000 312,000 317,000 MAX DESIGN

TAXI WEIGHT KILOGRAMS 128,820 136,985 141,521 143,789

POUNDS 282,000 300,000 310,000 315,000 MAX DESIGN

TAKEOFF WEIGHT KILOGRAMS 127,913 136,078 140,614 142,882

POUNDS 257,000 270,000 270,000 272,000 MAX DESIGN

LANDING WEIGHT KILOGRAMS 116,573 122,470 122,470 123,377

POUNDS 242,000 248,000 248,000 250,000 MAX DESIGN ZERO

FUEL WEIGHT KILOGRAMS 109,769 112,491 112,491 113,398

POUNDS 174,110 177,000 176,550 176,650 SPEC OPERATING

EMPTY WEIGHT (2) KILOGRAMS 78,975 80,286 80,082 80,127

POUNDS 67,890 71,000 71,450 73,350 MAX STRUCTURAL

PAYLOAD KILOGRAMS 30,794 32,205 32,409 33,271

ONE-CLASS FAA EXIT LIMIT = 255 (3) SEATING

CAPACITY MIXED CLASS 216 - 18 FIRST + 198 ECONOMY

CUBIC FEET 3,070 3,070 3,070 3,070 MAX CARGO

- LOWER DECK CUBIC METERS 86.9 86.9 86.9 86.9

US GALLONS 12,140 16,700 16,700 16,700

LITERS 45,955 63,217 63,217 63,217

POUNDS 81,338 111,890 111,890 111,890

USABLE FUEL

KILOGRAMS 36,894 50,753 50,753 50,753

NOTES: (1) SPEC WEIGHT FOR TYPICAL ENGINE/WEIGHT CONFIGURATION SHOWN

SEE TABLE 1.3.1 FOR COMBINATIONS AVAILABLE. CONSULT WITH AIRLINE FOR SPECIFIC

WEIGHTS AND CONFIGURATIONS.

(2) TYPICAL OPERATING EMPTY WEIGHT SHOWN. ACTUAL WEIGHT WILL

DEPEND ON SPECIFIC AIRLINE CONFIGURATION.

(3) 290 WITH SECOND OVERWING EXIT DOOR.

2.1.1 GENERAL CHARACTERISTICS

MODEL 767-200

D6-58328

10 SEPTEMBER 2005

CHARACTERISTICS UNITS 767-200ER (1)

POUNDS 337,000 347,000 352,200 381,000 388,000 396000 MAX DESIGN

TAXI WEIGHT KILOGRAMS 152,861 157,397 159,755 172,819 175,994 179,623

POUNDS 335,000 345,000 351,000 380,000 387,000 395000 MAX DESIGN

TAKEOFF WEIGHT KILOGRAMS 151,954 156,490 159,211 172,365 175,540 179,169

POUNDS 278,000 278,000 278,000 285,000 285,000 300000 MAX DESIGN

LANDING WEIGHT KILOGRAMS 126,099 126,099 126,099 129,274 129,274 136,078

POUNDS 253,000 253,000 253,000 260,000 260,000 260000 MAX DESIGN ZERO

FUEL WEIGHT KILOGRAMS 114,759 114,759 114,759 117,934 117,934 117,934

POUNDS 181,130 181,250 181,350 181,500 181,610 181610 SPEC OPERATING

EMPTY WEIGHT (2) KILOGRAMS 82,159 82,214 82,259 82,327 82,377 82,377

POUNDS 71,870 71,750 71,650 78,500 78,390 78,390 MAX STRUCTURAL

PAYLOAD KILOGRAMS 32,600 32,545 32,500 35,607 35,557 35,557

ONE-CLASS FAA EXIT LIMIT = 255 (3) SEATING

CAPACITY MIXED CLASS 216 - 18 FIRST + 198 ECONOMY

CUBIC FEET 3,070 3,070 3,070 3,070 3,070 3,070 MAX CARGO

- LOWER DECK CUBIC

METERS 86.9 86.9 86.9 86.9 86.9 86.9

US GALLONS 16,700 20,540 20,540 24,140 24,140 24140

LITERS 63,216 77,752 77,752 91,380 91,380 91,380

POUNDS 111,890 137,618 137,618 161,738 161,738 161,738

USABLE FUEL

KILOGRAMS 50,752 62,422 62,422 73,363 73,363 73,363

NOTES: (1) SPEC WEIGHT FOR TYPICAL ENGINE/WEIGHT CONFIGURATION SHOWN

SEE TABLE 1.3.1 FOR COMBINATIONS AVAILABLE. CONSULT WITH AIRLINE FOR SPECIFIC

WEIGHTS AND CONFIGURATIONS.

(2) TYPICAL OPERATING EMPTY WEIGHT SHOWN. ACTUAL WILL DEPEND ON SPECIFIC AIRLINE

CONFIGURATION.

(3) 290 WITH SECOND OVERWING EXIT DOOR.

2.1.2 GENERAL CHARACTERISTICS

MODEL 767-200ER

D6-58328 SEPTEMBER 2005 11

CHARACTERISTICS UNITS 767-300 (1)

MAX DESIGN POUNDS 347,000 352,000

TAXI WEIGHT KILOGRAMS 157,397 159,665

MAX DESIGN POUNDS 345,000 350,000

TAKEOFF WEIGHT KILOGRAMS 156,490 158,758

MAX DESIGN POUNDS 300,000 300,000

LANDING WEIGHT KILOGRAMS 136,078 136,078

MAX DESIGN ZERO POUNDS 278,000 278,000

FUEL WEIGHT KILOGRAMS 126,099 126,099

SPEC OPERATING POUNDS 186,380 189,750

EMPTY WEIGHT (2) KILOGRAMS 84,541 86,069

MAX STRUCTURAL POUNDS 91,620 88,250

PAYLOAD KILOGRAMS 41,558 40,230

SEATING ONE-CLASS FAA EXIT LIMIT 290 (3)

CAPACITY TWO-CLASS 261 - 24 FIRST + 237 ECONOMY

MAX CARGO CUBIC FEET 4,030 4,030

- LOWER DECK CUBIC METERS 114.1 114.1

USABLE FUEL US GALLONS 16,700 16,700

LITERS 63,216 63,216

POUNDS 111,890 111,890

KILOGRAMS 50,753 50,753

NOTES: (1) SPEC WEIGHT FOR TYPICAL ENGINE/WEIGHT CONFIGURATION SHOWN

SEE TABLE 1.3.1 FOR COMBINATIONS AVAILABLE. CONSULT WITH AIRLINE FOR SPECIFIC

WEIGHTS AND CONFIGURATIONS.

(2) TYPICAL OPERATING EMPTY WEIGHT SHOWN. ACTUAL WEIGHT WILL

DEPEND ON SPECIFIC AIRLINE CONFIGURATION.

(3) 299 WITH MID-CABIN TYPE A DOOR.

2.1.3 GENERAL CHARACTERISTICS

MODEL 767-300

D6-58328

12 SEPTEMBER 2005

CHARACTERISTICS UNITS 767-300ER (1)

POUNDS 381,000 388,000 401,000 409,000 413,000 MAX DESIGN

TAXI WEIGHT KILOGRAMS 172,819 175,994 181,891 185,519 187,334

POUNDS 380,000 387,000 400,000 407,000 412,000 MAX DESIGN

TAKEOFF WEIGHT KILOGRAMS 172,365 175,540 181,437 184,612 186,880

POUNDS 300,000 300,000 320,000 320,000 320,000 MAX DESIGN

LANDING WEIGHT KILOGRAMS 136,078 136,078 145,150 145,150 145,150

POUNDS 278,000 278,000 288,000 295,000 295,000 MAX DESIGN ZERO

FUEL WEIGHT KILOGRAMS 126,099 126,099 130,635 133,810 133,810

POUNDS 193,840 193,940 195,040 198,440 198,440 SPEC OPERATING

EMPTY WEIGHT (2) KILOGRAMS 87,924 87,970 88,469 90,011 90,011

POUNDS 84,160 84,060 92,960 96,560 96,560 MAX STRUCTURAL

PAYLOAD KILOGRAMS 38,174 38,129 42,166 43,799 43,799

ONE-CLASS FAA EXIT LIMIT = 290 (3) SEATING

CAPACITY MIXED CLASS 261 - 24 FIRST + 237 ECONOMY

CUBIC FEET 4,030 4,030 4,030 4,030 4,030 MAX CARGO

- LOWER DECK CUBIC METERS 114.1 114.1 114.1 114.1 114.1

US GALLONS 24,140 24,140 24,140 24,140 24,140

LITERS 91,380 91,380 91,380 91,380 91,380

POUNDS 161,740 161,740 161,740 161,740 161,740

USABLE FUEL

KILOGRAMS 73,364 73,364 73,364 73,364 73,364

NOTES: (1) SPEC WEIGHT FOR TYPICAL ENGINE/WEIGHT CONFIGURATION SHOWN

SEE TABLE 1.3.1 FOR COMBINATIONS AVAILABLE. CONSULT WITH AIRLINE FOR SPECIFIC

WEIGHTS AND CONFIGURATIONS.

(2) TYPICAL OPERATING EMPTY WEIGHT SHOWN. ACTUAL WEIGHT WILL

DEPEND ON SPECIFIC AIRLINE CONFIGURATION.

(3) 299 WITH SECOND OVERWING EXIT DOOR.

2.1.4 GENERAL CHARACTERISTICS

MODEL 767-300ER

D6-58328 SEPTEMBER 2005 13

767-300 FREIGHTER (1)

CHARACTERISTICS

UNITS CF6-80C2F PW 4000 RB211-524

POUNDS 409,000 413,000 409,000 413,000 409,000 413,000 MAX DESIGN

TAXI WEIGHT KILOGRAMS 185,519 187,334 185,519 187,334 185,519 187,334

POUNDS 408,000 412,000 408,000 412,000 408,000 412,000 MAX DESIGN

TAKEOFF WEIGHT KILOGRAMS 185,066 186,880 185,066 186,880 185,066 186,880

POUNDS 326,000 326,000 326,000 326,000 326,000 326,000 MAX DESIGN

LANDING WEIGHT KILOGRAMS 147,871 147,871 147,871 147,871 147,871 147,871

POUNDS 309,000 309,000 309,000 309,000 309,000 309,000 MAX DESIGN ZERO

FUEL WEIGHT KILOGRAMS 140,160 140,160 140,160 140,160 140,160 140,160

POUNDS 188,000 188,000 188,100 188,100 190,000 190,000 SPEC OPERATING

EMPTY WEIGHT (2) KILOGRAMS 85,275 85,275 85,321 85,321 86,183 86,183

POUNDS 121,000 121,000 120,900 120,900 119,000 119,000 MAX STRUCTURAL

PAYLOAD KILOGRAMS 54,885 54,885 54,839 54,839 53,978 53,978

(3) UP TO 24 TYPE A PALLETS AND 2 SPECIAL CONTOURED PALLETS MAX CARGO

- MAIN DECK (4) UP TO 14 M-1 PALLETS AND 2 SPECIAL CONTOURED PALLETS

CUBIC FEET 4,030 4,030 4,030 4,030 4,030 4,030 MAX CARGO

- LOWER DECK CUBIC METERS 114.1 114.1 114.1 114.1 114.1 114.1

US GALLONS 24,140 24,140 24,140 24,140 24,140 24140

LITERS 91,380 91,380 91,380 91,380 91,380 91,380

POUNDS 161,740 161,740 161,740 161,740 161,740 161,740

USABLE FUEL

KILOGRAMS 73,364 73,364 73,364 73,364 73,364 73,364

NOTES: (1) SPEC WEIGHT FOR TYPICAL ENGINE/WEIGHT CONFIGURATION SHOWN

SEE TABLE 1.3.1 FOR COMBINATIONS AVAILABLE. CONSULT WITH AIRLINE FOR SPECIFIC

WEIGHTS AND CONFIGURATIONS.

(2) TYPICAL OPERATING EMPTY WEIGHT SHOWN. ACTUAL WEIGHT WILL

DEPEND ON SPECIFIC AIRLINE CONFIGURATION.

(3) 767-300 FREIGHTER - SEE SEC 2.4.6 FOR PALLET DETAILS.

(4) 767-300 GENERAL MARKET FREIGHTER - SEE SEC 2.4.6 FOR PALLET DETAILS

2.1.5 GENERAL CHARACTERISTICS

MODEL 767-300 FREIGHTER

D6-58328

14 SEPTEMBER 2005

767-400ER (1)

CHARACTERISTICS

UNITS GE ENGINES PW ENGINES

POUNDS 451,000 451,000 MAX DESIGN

TAXI WEIGHT KILOGRAMS 204,570 204,570

POUNDS 450,000 450,000 MAX DESIGN

TAKEOFF WEIGHT KILOGRAMS 204,116 204,116

POUNDS 350,000 350,000 MAX DESIGN

LANDING WEIGHT KILOGRAMS 158,757 158,757

POUNDS 330,000 330,000 MAX DESIGN ZERO

FUEL WEIGHT KILOGRAMS 149,685 149,685

POUNDS 227,400 229,000 SPEC OPERATING

EMPTY WEIGHT (1) KILOGRAMS 103,147 103,872

POUNDS 102,600 101,000 MAX STRUCTURAL

PAYLOAD KILOGRAMS 46,538 45,813

ONE-CLASS 409 ALL ECONOMY

TWO-CLASS 296 - 24 FIRST + 272 ECONOMY

SEATING

CAPACITY (1) THREE-CLASS 243 - 16 FIRST + 36 BUSINESS + 189 ECONOMY

CUBIC FEET 4,905 4,905 MAX CARGO

- LOWER DECK (2) CUBIC METERS 138.9 138.9

US GALLONS 24,140 24,140

LITERS 91,370 91,370

POUNDS 161,738 161,738

USABLE FUEL

KILOGRAMS 73,363 73,363

NOTES: (1) SPEC WEIGHT FOR BASELINE CONFIGURATION OF 296 PASSENGERS.

CONSULT WITH AIRLINE FOR SPECIFIC WEIGHTS AND CONFIGURATIONS.

(2) FWD CARGO = 20 LD-2 CONTAINERS AT 120 CU FT EACH

AFT CARGO = 18 LD-2 CONTAINERS AT 120 CU FT EACH

BULK CARGO = 345 CU FT

2.1.6 GENERAL CHARACTERISTICS

MODEL 767-400ER

D6-58328 SEPTEMBER 2005 15

2.2.1 GENERAL DIMENSIONS

MODEL 767-200, -200ER

D6-58328

16 SEPTEMBER 2005

2.2.2 GENERAL DIMENSIONS

MODEL 767-300, -300ER

D6-58328 SEPTEMBER 2005 17

2.2.3 GENERAL DIMENSIONS

MODEL 767-300 FREIGHTER

D6-58328

18 SEPTEMBER 2005

2.2.4 GENERAL DIMENSIONS

MODEL 767-400ER

D6-58328 SEPTEMBER 2005 19

MINIMUM* MAXIMUM*

FEET - INCHES METERS FEET - INCHES METERS

A 23 - 6 7.16 24 - 6 7.47

B 5 - 8 1.73 6 - 9 2.06

C 13 - 5 4.09 14 - 8 4.47

D 7 - 5 2.26 8 - 3 2.51

E 15 - 1 4.60 15 - 1 4.60

F 7 - 5 2.26 8 - 3

2.51

G 7 - 6 2.29 8 - 6 2.59

H 13 - 4 4.06 14 – 6 4.42

J 51 – 2 15.60 52 – 11 16.13

K 2 – 8 0.81 3 – 7 1.09

L 16 – 3 4.95 18 – 3 5.56

M 12 – 9 3.89 14 – 3 4.34

N 19 – 6 5.94 21 – 7 6.58

NOTES: 1. VERTICAL CLEARANCES SHOWN OCCUR DURING MAXIMUM VARIATIONS OF AIRPLANE

ATTITUDE. COMBINATIONS OF AIRPLANE LOADING AND UNLOADING ACTIVITIES THAT

PRODUCE THE GREATEST POSSIBLE VARIATIONS IN ATTITUDE WERE USED TO

ESTABLISH THE VARIATIONS SHOWN.

2. DURING ROUTINE SERVICING, THE AIRPLANE REMAINS RELATIVELY STABLE,

PITCH AND ELEVATION CHANGES OCCURRING SLOWLY.

* NOMINAL DIMENSIONS

2.3.1 GROUND CLEARANCES

MODEL 767-200, -200ER.

D6-58328

20 SEPTEMBER 2005

MINIMUM* MAXIMUM*

FEET - INCHES METERS FEET - INCHES METERS

A 23 - 7 7.19 24 - 7 7.49

B 5 - 10 1.78 6 - 10 2.08

C 13 - 7 4.14 14 - 9 4.50

C’ 13 – 8 4.16 14 – 8 4.47

D 7 - 6 2.29 8 - 5 2.57

E 15 - 1 4.60 15 - 8 4.77

F 7 - 2 2.18 8 - 3

2.51

G 7 - 3 2.21 8 - 6 2.59

H 13 – 1 3.99 14 – 5 4.39

J 50 – 6 15.39 52 – 7 16.03

K 1 – 10 0.56 3 – 8 1.12

L 16 – 1 4.90 17 – 11 5.46

M 12 – 2 3.71 14 – 1 4.29

N 19 – 2 5.84 21 – 3 6.48

NOTES: 1. VERTICAL CLEARANCES SHOWN OCCUR DURING MAXIMUM VARIATIONS OF AIRPLANE

ATTITUDE. COMBINATIONS OF AIRPLANE LOADING AND UNLOADING ACTIVITIES THAT

PRODUCE THE GREATEST POSSIBLE VARIATIONS IN ATTITUDE WERE USED TO

ESTABLISH THE VARIATIONS SHOWN.

2. DURING ROUTINE SERVICING, THE AIRPLANE REMAINS RELATIVELY STABLE,

PITCH AND ELEVATION CHANGES OCCURRING SLOWLY.

* NOMINAL DIMENSIONS

2.3.2 GROUND CLEARANCES

MODEL 767-300, -300ER

D6-58328 SEPTEMBER 2005 21

MINIMUM* MAXIMUM*

FEET - INCHES METERS FEET - INCHES METERS

A 23 - 6 7.16 24 - 7 7.49

B 5 - 10 1.78 6 - 10 2.08

C 13 - 6 4.11 14 - 9 4.50

D 7 - 5 2.26 8 - 5 2.57

E 13 - 8 4.16 14 - 8 4.47

F 7 - 5 2.26 8 - 4

2.54

G 7 - 5 2.26 8 - 7 2.62

J 50 – 8 15.44 52 – 11 16.13

K 1 - 10 0.56 3 – 7 1.09

L 16 – 3 4.95 18 – 3 5.56

M 12 – 3 3.73 14 – 4 4.37

N 19 – 4 5.89 21 – 7 6.58

NOTES: 1. VERTICAL CLEARANCES SHOWN OCCUR DURING MAXIMUM VARIATIONS OF AIRPLANE

ATTITUDE. COMBINATIONS OF AIRPLANE LOADING AND UNLOADING ACTIVITIES THAT

PRODUCE THE GREATEST POSSIBLE VARIATIONS IN ATTITUDE WERE USED TO

ESTABLISH THE VARIATIONS SHOWN.

2. DURING ROUTINE SERVICING, THE AIRPLANE REMAINS RELATIVELY STABLE,

PITCH AND ELEVATION CHANGES OCCURRING SLOWLY.

* NOMINAL DIMENSIONS

2.3.3 GROUND CLEARANCES

MODEL 767-300 FREIGHTER

D6-58328

22 SEPTEMBER 2005

MINIMUM* MAXIMUM*

FEET - INCHES METERS FEET - INCHES METERS

A 23-8 7.22 24-6 7.46

B 5-11 1.81 6-9 2.05

C 13-7 4.13 14-5 4.39

D 7-10 2.38 8-7 2.61

E 14-6 4.41 15-1 4.59

F 9-8 2.96 10-6

3.20

G 10-1 3.07 10-11 3.33

H 16-1 4.91 17-0 5.18

J 54-9 16.68 55-10 17.01

K 3-11 1.21 4-5 1.36

L 19-11 6.08 21-4 6.51

M 16-4 4.89 17-1 5.22

N 23-5 7.12 24-5 7.45

NOTES: VERTICAL CLEARANCES SHOWN OCCUR DURING MAXIMUM VARIATIONS OF AIRPLANE

ATTITUDE. COMBINATIONS OF AIRPLANE LOADING AND UNLOADING ACTIVITIES THAT

PRODUCE THE GREATEST POSSIBLE VARIATIONS IN ATTITUDE WERE USED TO

ESTABLISH THE VARIATIONS SHOWN.

DURING ROUTINE SERVICING, THE AIRPLANE REMAINS RELATIVELY STABLE, PITCH AND ELEVATION CHANGES

OCCURRING SLOWLY.

* NOMINAL DIMENSIONS

2.3.4 GROUND CLEARANCES

MODEL 767-400ER.

D6-58328 SEPTEMBER 2005 23

2.4.1 INTERIOR ARRANGEMENTS – MIXED CLASS CONFIGURATIONS

MODEL 767-200, -200ER

D6-58328

24 SEPTEMBER 2005

2.4.2 INTERIOR ARRANGEMENTS – ALL-ECONOMY CLASS CONFIGURATIONS

MODEL 767-200, -200ER

D6-58328 SEPTEMBER 2005 25

2.4.3 INTERIOR ARRANGEMENTS – MIXED CLASS CONFIGURATIONS

MODEL 767-300, -300ER

D6-58328

26 SEPTEMBER 2005

2.4.4 INTERIOR ARRANGEMENTS – MIXED CLASS CONFIGURATIONS

MODEL 767-300, -300ER (TYPE A DOOR OPTION)

D6-58328 SEPTEMBER 2005 27

2.4.5 INTERIOR ARRANGEMENTS – ALL-ECONOMY CLASS CONFIGURATION

MODEL 767-300, -300ER

D6-58328

28 SEPTEMBER 2005

2.4.6 INTERIOR ARRANGEMENTS – MAIN DECK CARGO CONDIGURATION

MODEL 767-300 FREIGHTER

D6-58328 SEPTEMBER 2005 29

2.4.7 INTERIOR ARRANGEMENTS

MODEL 767-400ER

D6-58328

30 SEPTEMBER 2005

2.5.1 CABIN CROSS-SECTIONS - ECONOMY CLASS SEATS

MODEL 767-200, -200ER, -300, -300ER, -400ER

D6-58328 SEPTEMBER 2005 31

2.5.2 CABIN CROSS-SECTIONS - ALTERNATE SEATING ARRANGEMENTS

MODEL 767-200, -200ER, -300, -300ER, -400ER

D6-58328

32 SEPTEMBER 2005

FWD COMPARTMENT AFT COMPARTMENT

12 LD-2 CONTAINERS 10 LD-2 CONTAINERS BULK CARGO

TOTAL

CUBIC FEET 1,440 1,200 430 3,070

VOLUME

CUBIC

METERS 40.78 33.98 12.18 86.94

STRUCTURAL WEIGHT LIMIT

POUNDS 33,750 27,000 6,450 67,200 SEVEN-ABREAST

SEATING KILOGRAMS 15,309 12,247 2,926 30,481

POUNDS 21,600 18,000 6,450 46,050 EIGHT-ABREAST

SEATING KILOGRAMS 9,798 8,165 2,926 20,888

2.6.1 LOWER CARGO COMPARTMENTS – LD-2 CONTAINERS AND BULK CARGO

MODEL 767-200, -200ER

D6-58328 SEPTEMBER 2005 33

2.6.2 LOWER CARGO COMPARTMENTS – ALTERNATE ARRANGEMENTS

MODEL 767-200, -200ER

D6-58328

34 SEPTEMBER 2005

FWD COMPARTMENT AFT COMPARTMENT

16 LD-2 CONTAINERS 14 LD-2 CONTAINERS BULK CARGO

TOTAL

CUBIC FEET 1,920 1,680 430 4,030

VOLUME

CUBIC

METERS 54.4 47.6 12.2 114.2

STRUCTURAL WEIGHT LIMIT

POUNDS 45,000 37,800 6,450 89,250 SEVEN-ABREAST

SEATING KILOGRAMS 20,412 17,146 2,926 40,483

POUNDS 28,800 25,200 6,450 60,450 EIGHT-ABREAST

SEATING KILOGRAMS 13,063 11,431 2,926 27,420

2.6.3 LOWER CARGO COMPARTMENTS – LD-2 CONTAINERS AND BULK CARGO

MODEL 767-300, -300ER, -300 FREIGHTER

D6-58328 SEPTEMBER 2005 35

2.6.4 LOWER CARGO COMPARTMENTS – LD-2 CONTAINERS AND BULK CARGO

MODEL 767-300, -300ER, -300 FREIGHTER

D6-58328

36 SEPTEMBER 2005

2.6.5 LOWER CARGO COMPARTMENTS - CONTAINERS AND BULK CARGO

MODEL 767-400ER

D6-58328 SEPTEMBER 2005 37

2.7.1 DOOR CLEARANCES - PASSENGER AND SERVICE DOORS

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328

38 SEPTEMBER 2005

AFT OF NOSE

ABOVE

DOOR SILL

BELOW

DOOR SILL

NO SENSOR FT-IN M FT-IN M FT-IN M

1 TOTAL AIR TEMPERATURE

(LH SIDE ONLY) 4-3 1.39 2-4 0.71 - -

2 PITOT STATIC PROBE

(LH AND RH SIDES) 9-0 2.74 1-0 0.30 - -

3 ANGLE OF ATTACK

(LH AND RH SIDES) 8-3 2.51 - - 0-2 0.05

4 PITOT STATIC PROBES

(LH AND RH SIDES) 9-0 2.74 - - 0-6 0.15

5 FLUSH STATIC PORT

(LH AND RH SIDES) 31-0 9.45 - - 5-0 1.52

2.7.2 DOOR CLEARANCES - LOCATIONS OF PROBES AND SENSORS NEAR MAIN ENTRY

DOOR NO 1

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328 SEPTEMBER 2005 39

2.7.3 DOOR CLEARANCES – STANDARD FORWARD CARGO DOOR

MODEL 767-200, -200ER, -300, -300ER

D6-58328

40 SEPTEMBER 2005

2.7.4 DOOR CLEARANCES – LARGE FORWARD CARGO DOOR

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328 SEPTEMBER 2005 41

2.7.5 DOOR CLEARANCES - AFT CARGO DOOR

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328

42 SEPTEMBER 2005

2.7.6 DOOR CLEARANCES - BULK CARGO DOOR

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328 SEPTEMBER 2005 43

2.7.7 DOOR CLEARANCES – MAIN DECK CARGO DOOR

MODEL 767--300 FREIGHTER

D6-58328

44 SEPTEMBER 2005

THIS PAGE INTENTIONALLY LEFT BLANK

D6-58328 SEPTEMBER 2005 45

3.0 AIRPLANE PERFORMANCE

3.1 General Information

3.2 Payload/Range

3.3 F.A.R. Takeoff Runway Length Requirements

3.4 F.A.R. Landing Runway Length Requirements

D6-58328

46 SEPTEMBER 2005

3.0 AIRPLANE PERFORMANCE

3.1 General Information

The graph in Section 3.2 provides information on operational empty weight (OEW) and payload, trip

range, brake release gross weight, and fuel limits for a typical 767-200, -200ER, -300, -300ER, -300

Freighter, and -400ER airplanes. To use this graph, if the trip range and zero fuel weight (OEW +

payload) are known, the approximate brake release weight can be found, limited by fuel quantity.

The graphs in Section 3.3 provide information on F.A.R. takeoff runway length requirements with

typical engines at different pressure altitudes. Maximum takeoff weights shown on the graphs are

the heaviest for the particular airplane models with the corresponding engines. Standard day

temperatures for pressure altitudes shown on the F.A.R. takeoff graphs are given below:

PRESSURE ALTITUDE STANDARD DAY TEMP

FEET METERS oF oC

0 0 59.0 15.00

2,000 610 51.9 11.04

4,000 1,219 44.7 7.06

6,000 1,829 37.6 3.11

8,000 2,438 30.5 -0.85

10,000 3,048 23.3 -4.81

The graph in Section 3.4 provides information on landing runway length requirements for different

airplane weights and airport altitudes. The maximum landing weights shown are the heaviest for the

particular airplane model.

D6-58328 SEPTEMBER 2005 47

3.2.1 PAYLOAD/RANGE FOR LONG-RANGE CRUISE

MODEL 767-200

D6-58328

48 SEPTEMBER 2005

3.2.2 PAYLOAD/RANGE FOR LONG-RANGE CRUISE

MODEL 767-200ER

D6-58328 SEPTEMBER 2005 49

3.2.3 PAYLOAD/RANGE FOR LONG-RANGE CRUISE

MODEL 767-300

D6-58328

50 SEPTEMBER 2005

3.2.4 PAYLOAD/RANGE FOR LONG-RANGE CRUISE

MODEL 767-300ER-300 FREIGHTER

D6-58328 SEPTEMBER 2005 51

3.2.5 PAYLOAD/RANGE FOR LONG-RANGE CRUISE

MODEL 767-300ER (CF6-80C2B7F1 ENGINES)

D6-58328

52 SEPTEMBER 2005

3.2.6 PAYLOAD/RANGE FOR LONG-RANGE CRUISE

MODEL 767-300ER (PW4062 ENGINES)

D6-58328 SEPTEMBER 2005 53

3.2.7 PAYLOAD/RANGE FOR LONG-RANGE CRUISE

MODEL 767-300 FREIGHTER (CF6-80C2B7F1 ENGINES)

D6-58328

54 SEPTEMBER 2005

3.2.8 PAYLOAD/RANGE FOR LONG-RANGE CRUISE

MODEL 767-300 FREIGHTER (PW4062 ENGINES)

D6-58328 SEPTEMBER 2005 55

3.2.9 PAYLOAD/RANGE FOR LONG-RANGE CRUISE

MODEL 767-400ER (CF6-80C2B8 ENGINES)

D6-58328

56 SEPTEMBER 2005

3.2.10 PAYLOAD/RANGE FOR LONG-RANGE CRUISE

MODEL 767-400ER (PW4062 ENGINES)

D6-58328 SEPTEMBER 2005 57

3.3.1 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY

MODEL 767-200, -200ER (JT9D-7R4D/7R4E , CF6-80A/80A2 ENGINES)

D6-58328

58 SEPTEMBER 2005

3.3.2 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY +31oF (STD + 17oC)

MODEL 767-200, -200ER (JT9D-7R4D/7R4E, CF6-80A/80A2 ENGINES)

D6-58328 SEPTEMBER 2005 59

3.3.3 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY

MODEL 767-200, -200ER (CF6-80C2B2, PW4052 ENGINES)

D6-58328

60 SEPTEMBER 2005

3.3.4 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY +31oF (STD + 17oC)

MODEL 767-200, -200ER (CF6-80C2B2, PW4052 ENGINES)

D6-58328 SEPTEMBER 2005 61

3.3.5 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY

MODEL 767-200ER (CF6-80C2B4, PW4056, RB211-524G ENGINES)

D6-58328

62 SEPTEMBER 2005

3.3.6 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 31oF (STD + 17oC)

MODEL 767-200ER (CF6-80C2B4, PW4056, RB211-524G ENGINES)

D6-58328 SEPTEMBER 2005 63

3.3.7 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY

MODEL 767-300 ( CF6-80A/80A2 ENGINES)

D6-58328

64 SEPTEMBER 2005

3.3.8 FAA TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 33oF (STD + 18oC)

MODEL 767-300 (CF6-80A/80A2 ENGINES)

D6-58328 SEPTEMBER 2005 65

3.3.9 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY

MODEL 767-300 (JT9D-7R4D/7R4E ENGINES)

D6-58328

66 SEPTEMBER 2005

3.3.10 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 27oF (STD + 15oC)

MODEL 767-300 (JT9D-7R4D/7R4E ENGINES)

D6-58328 SEPTEMBER 2005 67

3.3.11 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY

MODEL 767-300 (CF6-80C2B2, PW4052 ENGINES)

D6-58328

68 SEPTEMBER 2005

3.3.12 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 31oF (STD + 17oC)

MODEL 767-300 (CF6-80C2B2, PW4052 ENGINES)

D6-58328 SEPTEMBER 2005 69

3.3.13 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY

MODEL 767-300ER, -300 FREIGHTER (CF6-80C2B4, PW4056, RB211-524G ENGINES)

D6-58328

70 SEPTEMBER 2005

3.3.14 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 31oF (STD + 17oC)

MODEL 767-300ER, -300 FREIGHTER (CF6-80C2B4, PW4052, RB211-524G ENGINES)

D6-58328 SEPTEMBER 2005 71

3.3.15 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY

MODEL 767-300ER, -300 FREIGHTER (CF6-80C2B64, PW4060, RB211-524H ENGINES)

D6-58328

72 SEPTEMBER 2005

3.3.16 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 27oF (STD + 15oC)

MODEL 767-300ER, -300 FREIGHTER (CF6-80C2B6, PW4060, RB211-524H ENGINES)

D6-58328 SEPTEMBER 2005 73

3.3.17 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY

MODEL 767-300ER (CF6-80C2B7F ENGINES)

D6-58328

74 SEPTEMBER 2005

3.3.18 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 27oF (STD + 15oC)

MODEL 767-300ER (CF6-80C2B7F ENGINES)

D6-58328 SEPTEMBER 2005 75

3.3.19 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY

MODEL 767-300ER (PW4062 ENGINES)

D6-58328

76 SEPTEMBER 2005

3.3.20 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 27oF (STD + 15oC)

MODEL 767-300ER (PW4062 ENGINES)

D6-58328 SEPTEMBER 2005 77

3.3.21 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY

MODEL 767-300 FREIGHTER (CF6-80C2B7F ENGINES)

D6-58328

78 SEPTEMBER 2005

3.3.22 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 27oF (STD + 15oC)

MODEL 767-300 FREIGHTER (CF6-80C2B7F ENGINES)

D6-58328 SEPTEMBER 2005 79

3.3.23 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY

MODEL 767-300 FREIGHTER (PW4062 ENGINES)

D6-58328

80 SEPTEMBER 2005

3.3.24 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 27oF (STD + 15oC)

MODEL 767-300 FREIGHTER (PW4062 ENGINES)

D6-58328 SEPTEMBER 2005 81

3.3.25 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY,

DRY RUNWAY SURFACE

MODEL 767-400ER (CF6-80C2B8F ENGINES)

D6-58328

82 SEPTEMBER 2005

3.3.26 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 31oF (STD + 17oC) , DRY RUNWAY SURFACE

MODEL 767-400ER (CF6-80C2B8F ENGINES)

D6-58328 SEPTEMBER 2005 83

3.3.27 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY,

WET SMOOTH RUNWAY SURFACE

MODEL 767-400ER (CF6-80C2B8F ENGINES)

D6-58328

84 SEPTEMBER 2005

3.3.28 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 27oF (STD + 15oC), WET SMOOTH RUNWAY SURFACE

MODEL 767-400ER (CF6-80C2B8F ENGINES)

D6-58328 SEPTEMBER 2005 85

3.3.29 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY,

DRY RUNWAY SURFACE

MODEL 767-400ER (CF6-80C2B7F1 ENGINES)

D6-58328

86 SEPTEMBER 2005

3.3.30 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 27oF (STD + 15oC), DRY RUNWAY SURFACE

MODEL 767-400ER (CF6-80C2B7F1 ENGINES)

D6-58328 SEPTEMBER 2005 87

3.3.31 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY,

WET SMOOTH RUNWAY SURFACE

MODEL 767-400ER (CF6-80C2B7F1 ENGINES)

D6-58328

88 SEPTEMBER 2005

3.3.32 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 27oF (STD + 15oC), WET SMOOTH RUNWAY SURFACE

MODEL 767-400ER (CF6-80C2B7F1 ENGINES)

D6-58328 SEPTEMBER 2005 89

3.3.33 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY,

DRY RUNWAY SURFACE

MODEL 767-400ER (PW4062 ENGINES)

D6-58328

90 SEPTEMBER 2005

3.3.34 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 27oF (STD + 15oC), DRY RUNWAY SURFACE

MODEL 767-400ER (PW4062 ENGINES)

D6-58328 SEPTEMBER 2005 91

3.3.35 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS - STANDARD DAY,

WET SMOOTH RUNWAY SURFACE

MODEL 767-400ER (PW4062 ENGINES)

D6-58328

92 SEPTEMBER 2005

3.3.36 F.A.R. TAKEOFF RUNWAY LENGTH REQUIREMENTS

STANDARD DAY + 27oF (STD + 15oC), WET SMOOTH RUNWAY SURFACE

MODEL 767-400ER (PW4062 ENGINES)

D6-58328 SEPTEMBER 2005 93

3.4.1 FAA LANDING RUNWAY LENGTH REQUIREMENTS - FLAPS 25

MODEL 767-200, -200ER

D6-58328

94 SEPTEMBER 2005

3.4.2 FAA LANDING RUNWAY LENGTH REQUIREMENTS - FLAPS 30

MODEL 767-200, -200ER

D6-58328 SEPTEMBER 2005 95

3.4.3 FAA LANDING RUNWAY LENGTH REQUIREMENTS - FLAPS 25

MODEL 767-300

D6-58328

96 SEPTEMBER 2005

3.4.4 FAA LANDING RUNWAY LENGTH REQUIREMENTS - FLAPS 30

MODEL 767—300

D6-58328 SEPTEMBER 2005 97

3.4.5 FAA LANDING RUNWAY LENGTH REQUIREMENTS - FLAPS 25

MODEL 767—300ER

D6-58328

98 SEPTEMBER 2005

3.4.6 FAA LANDING RUNWAY LENGTH REQUIREMENTS - FLAPS 30

MODEL 767—300ER

D6-58328 SEPTEMBER 2005 99

3.4.7 FAA LANDING RUNWAY LENGTH REQUIREMENTS - FLAPS 25

MODEL 767—300 FREIGHTER

D6-58328

100 SEPTEMBER 2005

3.4.8 FAA LANDNG RUNWAY LENGTH REQUIREMENTS - FLAPS 30

MODEL 767—300 FREIGHTER

D6-58328 SEPTEMBER 2005 101

3.4.9 FAA LANDING RUNWAY LENGTH REQUIREMENTS - FLAPS 25

MODEL 767-400ER

D6-58328

102 SEPTEMBER 2005

3.4.10 FAA LANDNG RUNWAY LENGTH REQUIREMENTS - FLAPS 30

MODEL 767-400ER

D6-58328 SEPTEMBER 2005 103

4.0 GROUND MANEUVERING

4.1 General Information

4.2 Turning Radii

4.3 Clearance Radii

4.4 Visibility From Cockpit in Static Position

4.5 Runway and Taxiway Turn Paths

4.6 Runway Holding Bay

D6-58328

104 SEPTEMBER 2005

4.0 GROUND MANEUVERING

4.1 General Information

This section provides airplane turning capability and maneuvering characteristics.

For ease of presentation, these data have been determined from the theoretical limits imposed by the

geometry of the aircraft, and where noted, provide for a normal allowance for tire slippage. As such,

they reflect the turning capability of the aircraft in favorable operating circumstances. These data

should be used only as guidelines for the method of determination of such parameters and for the

maneuvering characteristics of this aircraft.

In the ground operating mode, varying airline practices may demand that more conservative turning

procedures be adopted to avoid excessive tire wear and reduce possible maintenance problems.

Airline operating procedures will vary in the level of performance over a wide range of operating

circumstances throughout the world. Variations from standard aircraft operating patterns may be

necessary to satisfy physical constraints within the maneuvering area, such as adverse grades, limited

area, or high risk of jet blast damage. For these reasons, ground maneuvering requirements should be

coordinated with the using airlines prior to layout planning.

Section 4.2 shows turning radii for various nose gear steering angles. Radii for the main and nose

gears are measured from the turn center to the outside of the tire.

Section 4.3 provides data on minimum width of pavement required for 180o turn.

Section 4.4 shows the pilot’s visibility from the cockpit and the limits of ambinocular vision through

the windows. Ambinocular vision is defined as the total field of vision seen simultaneously by both

eyes.

Section 4.5 shows approximate wheel paths of a 767 on runway to taxiway, and taxiway to taxiway

turns.

Section 4.6 illustrates a typical runway holding bay configuration.

D6-58328 SEPTEMBER 2005 105

NOTES: * ACTUAL OPERATING TURNING RADII MAY BE GREATER THAN SHOWN.

* CONSULT WITH AIRLINE FOR SPECIFIC OPERATING PROCEDURE

R-1

INNER GEAR R-2

OUTER GEAR R-3

NOSE GEAR R-4

WING TIP R-5

NOSE R-6

TAIL

STEERING

ANGLE

(DEG) FT M FT M FT M FT M FT M FT M

30 94.0 28.7 129.7 39.5 130.8 39.9 192.1 58.5 137.3 41.8 161.8 49.3

35 74.4 22.7 110.1 33.6 114.3 34.8 172.7 52.6 121.8 37.1 144.8 44.1

40 59.1 18.0 94.8 28.9 102.1 31.1 157.6 48.0 110.7 33.7 132.1 40.3

45 46.7 14.2 82.4 25.1 93.0 28.3 145.4 44.3 102.4 31.2 122.2 37.3

50 36.4 11.1 72.1 22.0 86.0 26.2 135.2 41.2 96.2 29.3 114.3 34.8

55 27.4 8.3 63.1 19.2 80.5 24.5 126.5 38.6 91.5 27.9 107.8 32.9

60 19.4 5.9 55.1 16.8 76.2 23.2 118.7 36.2 87.8 26.8 102.4 31.2

65 (MAX) 12.3 3.7 48.0 14.6 72.9 22.2 111.8 34.1 85.0 25.9 97.8 29.8

4.2.1 TURNING RADII - NO SLIP ANGLE

MODEL 767-200, -200ER

D6-58328

106 SEPTEMBER 2005

NOTES: *ACTUAL OPERATING TURNING RADII MAY BE GREATER THAN SHOWN.

* CONSULT WITH AIRLINE FOR SPECIFIC OPERATING PROCEDURE

R-1

INNER GEAR R-2

OUTER GEAR R-3

NOSE GEAR R-4

WING TIP R-5

NOSE R-6

TAIL

STEERING

ANGLE

(DEG) FT M FT M FT M FT M FT M FT M

30 111.5 34.0 147.3 44.9 151.0 46.0 209.4 63.8 157.4 48.0 181.8 55.4

35 88.8 27.1 124.6 38.0 131.9 40.2 186.9 57.0 139.3 42.5 162.2 49.4

40 71.1 21.7 106.9 32.6 117.9 35.9 169.5 51.7 126.3 38.5 147.6 45.0

45 56.8 17.3 92.6 28.2 107.3 32.7 155.4 47.4 116.7 35.6 136.2 41.5

50 44.8 13.6 80.6 24.6 99.2 30.2 143.5 43.8 109.3 33.3 127.2 38.8

55 34.4 10.5 70.2 21.4 92.8 28.3 133.4 40.7 103.7 31.6 119.8 36.5

60 25.2 7.7 61.0 18.6 87.9 26.8 124.4 37.9 99.4 30.3 113.6 34.6

65 (MAX) 16.9 5.2 52.7 16.1 84.1 25.6 116.4 35.5 96.1 29.3 108.4 33.1

4.2.2 TURNING RADII - NO SLIP ANGLE

MODEL 767-300, -300ER, -300 FREIGHTER

D6-58328 SEPTEMBER 2005 107

NOTES: *ACTUAL OPERATING TURNING RADII MAY BE GREATER THAN SHOWN.

* CONSULT WITH AIRLINE FOR SPECIFIC OPERATING PROCEDURE

STEERING

ANGLE R1

INNER GEAR R2

OUTER GEAR R3

NOSE GEAR R4

WING TIP R5

NOSE R6

TAIL

(DEG) FT M FT M FT M FT M FT M FT M

30 130.5 39.8 166.3 50.7 173.0

52.7 236.0

71.8 179.3

54.7 203.4

62.0

35 104.5 31.8 140.3 42.8 151.1

46.0 210.3

63.9 158.4

48.3 180.9

55.1

40 84.2 25.7 120.0 36.6 135.0

41.1 190.3

57.8 143.4

43.7 164.1

50.0

45 67.8 20.7 103.6 31.6 122.8

37.4 174.1

52.9 132.2

40.3 151.1

46.1

50 54.0 16.5 89.8 27.4 113.5

34.6 160.6

48.7 123.7

37.7 140.8

42.9

55 42.1 12.8 77.9 23.7 106.3

32.4 149.0

45.2 117.1

35.7 132.4

40.4

60 31.6 9.6 67.4 20.5 100.6

30.7 138.7

42.0 112.1

34.2 125.4

38.2

65 (MAX) 22.1 6.7 57.9 17.6 96.2 29.3 129.5

39.2 108.2

33.0 119.6

36.5

4.2.3 TURNING RADII - NO SLIP ANGLE

MODEL 767-400ER

D6-58328

108 SEPTEMBER 2005

NOTES: * TIRE SLIP ANGLE APPROXIMATE FOR 61° STEERING ANGLE

* CONSULT USING AIRLINE FOR SPECIFIC OPERATING PROCEDURE

EFFECTIVE

STEERING X Y A R3 R4 R5 R6

MODEL ANGLE

(DEG) FT M FT M FT M FT M FT M FT M FT M

-200, -

200ER 61 64.6 19.7 35.8 10.9 129.2 39.4 75.5 23.0 117.3 35.8 87.2 26.6 101.4 30.9

-300, -

300ER,

-300F

61 74.7 22.8 41.4 12.6 146.3 44.6 87.0 26.5 122.7 37.4 98.7 30.1 112.5 34.3

-400ER 61 85.7 26.1 47.5 14.5 165.1 50.3 99.6 30.4 136.8 41.7 111.3 33.9 124.2 37.9

4.3 CLEARANCE RADII

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER -400ER

D6-58328 SEPTEMBER 2005 109

4.4 VISIBILITY FROM COCKPIT IN STATIC POSITION

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328

110 SEPTEMBER 2005

4.5.1 RUNWAY AND TAXIWAY TURNPATHS - RUNWAY-TO-TAXIWAY,

MORE THAN 90-DEGREE TURN

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328 SEPTEMBER 2005 111

4.5.2 RUNWAY AND TAXIWAY TURNPATHS - RUNWAY-TO-TAXIWAY, 90-DEGREE TURN

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328

112 SEPTEMBER 2005

4.5.3 RUNWAY AND TAXIWAY TURNPATHS - TAXIWAY-TO-TAXIWAY,

90-DEGREE TURN, NOSE GEAR TRACKS CENTERLINE

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328 SEPTEMBER 2005 113

4.5.4 RUNWAY AND TAXIWAY TURNPATHS - TAXIWAY-TO-TAXIWAY,

90-DEGREE TURN, COCKPIT TRACKS CENTERLINE

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328

114 SEPTEMBER 2005

4.5.5 RUNWAY AND TAXIWAY TURNPATHS - TAXIWAY-TO-TAXIWAY,

90-DEGREE TURN, JUDGMENTAL OVERSTEERING

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328 SEPTEMBER 2005 115

4.6 RUNWAY HOLDING BAY

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328

116 SEPTEMBER 2005

THIS PAGE INTENTIONALLY LEFT BLANK

D6-58328 SEPTEMBER 2005 117

5.0 TERMINAL SERVICING

5.1 Airplane Servicing Arrangement - Typical Turnaround

5.2 Terminal Operations - Turnaround Station

5.3 Terminal Operations - En Route Station

5.4 Ground Servicing Connections

5.5 Engine Starting Pneumatic Requirements

5.6 Ground Pneumatic Power Requirements

5.7 Conditioned Air Requirements

5.8 Ground Towing Requirements

D6-58328

118 SEPTEMBER 2005

5.0 TERMINAL SERVICING

During turnaround at the terminal, certain services must be performed on the aircraft, usually within a

given time, to meet flight schedules. This section shows service vehicle arrangements, schedules,

locations of service points, and typical service requirements. The data presented in this section

reflect ideal conditions for a single airplane. Service requirements may vary according to airplane

condition and airline procedure.

Section 5.1 shows typical arrangements of ground support equipment during turnaround. As noted, if

the auxiliary power unit (APU) is used, the electrical, air start, and air-conditioning service vehicles

would not be required. Passenger loading bridges or portable passenger stairs could be used to load

or unload passengers.

Sections 5.2 and 5.3 show typical service times at the terminal. These charts give typical schedules

for performing service on the airplane within a given time. Service times could be rearranged to suit

availability of personnel, airplane configuration, and degree of service required.

Section 5.4 shows the locations of ground service connections in graphic and in tabular forms.

Typical capacities and service requirements are shown in the tables. Services with requirements that

vary with conditions are described in subsequent sections.

Section 5.5 shows typical sea level air pressure and flow requirements for starting different engines.

The curves are based on an engine start time of 90 seconds.

Section 5.6 shows air conditioning requirements for heating and cooling (pull-down and pull-up) using

ground conditioned air. The curves show airflow requirements to heat or cool the airplane within a

given time at ambient conditions.

Section 5.7 shows air conditioning requirements for heating and cooling to maintain a constant cabin

air temperature using low pressure conditioned air. This conditioned air is supplied through an 8-in

(20.3 cm) ground air connection (GAC) directly to the passenger cabin, bypassing the air cycle

machines.

Section 5.8 shows ground towing requirements for various ground surface conditions.

D6-58328 SEPTEMBER 2005 119

5.1.1 AIRPLANE SERVICING ARRANGEMENT - TYPICAL TURNAROUND

MODEL 767-200, -200ER

D6-58328

120 SEPTEMBER 2005

5.1.2 AIRPLANE SERVICING ARRANGEMENT - TYPICAL TURNAROUND

MODEL 767-300, -300ER

D6-58328 SEPTEMBER 2005 121

5.1.3 AIRPLANE SERVICING ARRANGEMENT - TYPICAL TURNAROUND

MODEL 767-300 FREIGHTER

D6-58328

122 SEPTEMBER 2005

5.1.4 AIRPLANE SERVICING ARRANGEMENT - TYPICAL TURNAROUND

MODEL 767-400ER

D6-58328 SEPTEMBER 2005 123

5.2.1 TERMINAL OPERATIONS - TURNAROUND STATION

MODEL 767-200

D6-58328

124 SEPTEMBER 2005

5.2.2 TERMINAL OPERATIONS - TURNAROUND STATION

MODEL 767-200ER

D6-58328 SEPTEMBER 2005 125

5.2.3 TERMINAL OPERATIONS - TURNAROUND STATION

MODEL 767-300

D6-58328

126 SEPTEMBER 2005

5.2.4 TERMINAL OPERATIONS - TURNAROUND STATION

MODEL 767-300ER

D6-58328 SEPTEMBER 2005 127

5.2.5 TERMINAL OPERATIONS - TURNAROUND STATION

MODEL 767-300 FREIGHTER

D6-58328

128 SEPTEMBER 2005

5.2.6 TERMINAL OPERATIONS - TURNAROUND STATION

MODEL 767-400ER

D6-58328 SEPTEMBER 2005 129

5.3.1 TERMINAL OPERATIONS - EN ROUTE STATION

MODEL 767-200, -200ER

D6-58328

130 SEPTEMBER 2005

5.3.2 TERMINAL OPERATIONS - EN ROUTE STATION

MODEL 767-300, -300ER

D6-58328 SEPTEMBER 2005 131

5.3.3 TERMINAL OPERATIONS - EN ROUTE STATION

MODEL 767-400ER

D6-58328

132 SEPTEMBER 2005

5.4.1 GROUND SERVICING CONNECTIONS

MODEL 767-200, -200ER

D6-58328 SEPTEMBER 2005 133

5.4.2 GROUND SERVICING CONNECTIONS

MODEL 767-300, -300ER

D6-58328

134 SEPTEMBER 2005

5.4.3 GROUND SERVICING CONNECTIONS

MODEL 767-300 FREIGHTER

D6-58328 SEPTEMBER 2005 135

5.4.4 GROUND SERVICING CONNECTIONS

MODEL 767-400ER

D6-58328

136 SEPTEMBER 2005

DISTANCE FROM AIRPLANE

CENTERLINE MAX HT

ABOVE

DISTANCE

AFT OF

NOSE LH SIDE RH SIDE GROUND

SYSTEM

MODEL FT M FT M FT M FT M

CONDITIONED AIR

ONE 8-IN (20.3 CM) PORT

-200,

-200ER,

-300,

-300ER,

-300 F

-400ER

17.7

20.8

24.1

1.5

2.1

ELECTRICAL

TWO CONNECTIONS

90 KVA , 200/115 V AC 400 HZ,

3-PHASE EACH

ALL

5.5

0.9

2.1

FUEL

TWO UNDERWING PRESSURE

CONNECTORS ON EACH WING

FUEL VENTS

TOTAL TANK CAPACITY:

-200, -300, -300 FREIGHTER

16,700 U.S. GAL (63,210 L)

-200ER

20,450 U.S. GAL (77,410 L)

-300ER, -400ER

24,140 U.S. GAL (91,370 L)

MAX FUEL RATE:

1,000 GPM (3,970 LPM)

MAX FILL PRESSURE:

55 PSIG (3.87 KG/CM2)

-200

-200ER

-300

-300ER

-300 F

-400ER

-200

-200ER

-300

-300ER

-300 F

-400ER

101

102

103

113

124

24.4

24.7

27.4

27.7

30.8

31.1

31.4

34.4

37.8

13.7

14.0

13.7

14.0

13.7

14.0

21.3

13.7

14.0

13.7

14.0

13.7

14.0

21.3

4.5

4.3

4.5

5.2

5.4.5 GROUND SERVICING CONNECTIONS AND CAPACITIES

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328 SEPTEMBER 2005 137

DISTANCE FROM AIRPLANE

CENTERLINE

DISTANCE

AFT OF

NOSE LH SIDE RH SIDE

MAX HT

ABOVE

GROUND

SYSTEM

MODEL

FT M FT FT M FT

HYDRAULIC

ONE SERVICE CONNECTION

TOTAL SYSTEM CAPACITY

= 80 GAL (303 L)

FILL PRESSURE

= 150 PSIG (10.55 KG/CM2)

-200,

-200ER,

-300,

-300ER,

-300 F

-400ER

108

26.5

29.6

32.9

1.8

2.1

LAVATORY

BOTH FORWARD AND AFT TOILETS

ARE SERVICED THROUGH ONE

SERVICE PANEL

THREE SERVICE CONNECTIONS :

DRAIN – ONE 4 IN (10.2 CM)

FLUSH – TWO 1 IN (2.5 CM)

TOILET FLUSH REQUIREMENTS:

FLOW – 10 GPM (38 LPM)

PRESSURE 30 PSIG (2.11 KG/SC CM)

TOTAL SERVICE TANK

REQUIREMENTS:

WASTE – 140 US GAL (530 L)

FLUSH – 50 US GAL (189 L)

PRECHARGE – 12 US GAL (45 L)

-200,

-200ER,

-300,

-300ER

-400ER

123

144

165

37.5

43.9

50.3

3.0

OXYGEN

CREW SYSTEM USES

REPLACEABLE CYLINDERS

PASSENGER SYSTEM USES

SELF-CONTAINED OXYGEN

GENERATION UNITS

ALL

1.8

0.6

3.0

PNEUMATIC

TWO 3-IN(7.6-CM) PORTS

-200,

-200ER,

-300,

-300ER,

-300 F

-400ER

18.6

18.9

21.6

21.9

25.0

25.3

0.9

2.1

5.4.6 GROUND SERVICING CONNECTIONS AND CAPACITIES

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328

138 SEPTEMBER 2005

DISTANCE FROM AIRPLANE

CENTERLINE

DISTANCE

AFT OF

NOSE LH SIDE RH SIDE

MAX HT

ABOVE

GROUND

SYSTEM

MODEL

FT M FT M FT M FT M

POTABLE WATER

ONE SERVICE CONNECTION (BASIC)

OPTIONAL LOCATION

ONE SERVICE CONNECTION (BASIC)

FORWARD DRAIN PANEL

TANK CAPACITY

102 U.S. GAL (386 L)

149 U.S. GAL (564 L)

FILL PORT – ¾ IN (1.9 CM)

MAX FILL PRESSURE

= 25 PSIG (1.76 KG/SQ CM)

-200,

-200ER

-200,

-300,

-300ER,

-300 F

-400ER

ALL

-200,

-300

-200ER

-300ER

-400ER

107

121

128

149

32.6

36.8

39.0

44.4

14.0

0.3

0.1

2.4

2.1

5.5

2.1

5.4.7 GROUND SERVICING CONNECTIONS AND CAPACITIES

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328 SEPTEMBER 2005 139

5.5.1 ENGINE START PNEUMATIC REQUIREMENTS - SEA LEVEL

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER (GE ENGINES)

D6-58328

140 SEPTEMBER 2005

5.5.2 ENGINE START PNEUMATIC REQUIREMENTS - SEA LEVEL

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER (PRATT & WHITNEY ENGINES)

D6-58328 SEPTEMBER 2005 141

5.5.3 ENGINE START PNEUMATIC REQUIREMENTS - SEA LEVEL

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER (GENERAL ELECTRIC ENGINES)

D6-58328

142 SEPTEMBER 2005

5.5.4 ENGINE START PNEUMATIC REQUIREMENTS - SEA LEVEL

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER (GENERAL ELECTRIC ENGINES)

D6-58328 SEPTEMBER 2005 143

5.5.5 ENGINE START PNEUMATIC REQUIREMENTS - SEA LEVEL

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER (ROLLS ROYCE ENGINES)

D6-58328

144 SEPTEMBER 2005

5.6.1 GROUND PNEUMATIC POWER REQUIREMENTS - HEATING AND COOLING

MODEL 767-200, -200ER

D6-58328 SEPTEMBER 2005 145

5.6.2 GROUND PNEUMATIC POWER REQUIREMENTS - HEATING AND COOLING

MODEL 767-300, -300ER

D6-58328

146 SEPTEMBER 2005

5.6.3 GROUND PNEUMATIC POWER REQUIREMENTS - HEATING AND COOLING

MODEL 767-400ER

D6-58328 SEPTEMBER 2005 147

5.7.1 CONDITIONED AIR FLOW REQUIREMENTS – STEADY STATE

MODEL 767-200, -200ER

D6-58328

148 SEPTEMBER 2005

5.7.2 CONDITIONED AIR REQUIREMENTS – STEADY STATE

MODEL 767-300, -300ER, -300 FREIGHTER

D6-58328 SEPTEMBER 2005 149

5.7.3 CONDITIONED AIR REQUIREMENTS

MODEL 767-400ER

D6-58328

150 SEPTEMBER 2005

5.7.4 CONDITIONED AIR FLOW PRESSURE REQUIREMENTS

MODEL 767-400ER

D6-58328 SEPTEMBER 2005 151

5.8.1 GROUND TOWING REQUIREMENTS - ENGLISH UNITS

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328

152 SEPTEMBER 2005

5.8.2 GROUND TOWING REQUIREMENTS - METRIC UNITS

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER

D6-58328

SEPTEMBER 2005 153

6.0 JET ENGINE WAKE AND NOISE DATA

6.1 Jet Engine Exhaust Velocities and Temperatures

6.2 Airport and Community Noise

D6-58328

154 SEPTEMBER 2005

6.0 JET ENGINE WAKE AND NOISE DATA

6.1 Jet Engine Exhaust Velocities and Temperatures

This section shows exhaust velocity and temperature contours aft of the 767-200, -300, -400ER

airplane. The contours were calculated from a standard computer analysis using three-dimensional

viscous flow equations with mixing of primary, fan, and free-stream flow. The presence of the

ground plane is included in the calculations as well as engine tilt and toe-in. Mixing of flows from the

engines is also calculated. The analysis does not include thermal buoyancy effects which tend to

elevate the jet wake above the ground plane. The buoyancy effects are considered to be small

relative to the exhaust velocity and therefore are not included.

The graphs show jet wake velocity and temperature contours for representative engines. The results

are valid for sea level, static, standard day conditions. The effect of wind on jet wakes is not

included. There is evidence to show that a downwind or an upwind component does not simply add

or subtract from the jet wake velocity, but rather carries the whole envelope in the direction of the

wind. Crosswinds may carry the jet wake contour far to the side at large distances behind the

airplane.

D6-58328

SEPTEMBER 2005 155

6.1.1 PREDICTED JET ENGINE EXHAUST VELOCITY CONTOURS

- IDLE THRUST

MODEL 767-200, -200ER, -300 (JT9D-7R4D, -7R4E ENGINES)

D6-58328

156 SEPTEMBER 2005

6.1.2 PREDICTED JET ENGINE EXHAUST VELOCITY CONTOURS

- IDLE THRUST

MODEL 767-200, -200ER, -300 (CF6-80A, -80A2 ENGINES)

D6-58328

SEPTEMBER 2005 157

6.1.3 PREDICTED JET ENGINE EXHAUST VELOCITY CONTOURS

- IDLE THRUST

MODEL 767-300, -300ER, -300 FREIGHTER (PW4000, CF6-80C2 SERIES ENGINES)

D6-58328

158 SEPTEMBER 2005

6.1.4 PREDICTED JET ENGINE EXHAUST VELOCITY CONTOURS

- IDLE THRUST

MODEL 767-300, -300ER, -300 FREIGHTER (RB211-524 ENGINES)

D6-58328

SEPTEMBER 2005 159

6.1.5 PREDICTED JET ENGINE EXHAUST VELOCITY CONTOURS

- IDLE THRUST

MODEL 767-400ER (ALL ENGINES)

D6-58328

160 SEPTEMBER 2005

6.1.6 PREDICTED JET ENGINE EXHAUST VELOCITY CONTOURS

- LOW BREAKAWAY THRUST

MODEL 767-200, -200ER, -300 (JT9D-7R4D, -7R4E ENGINES)

D6-58328

SEPTEMBER 2005 161

6.1.7 PREDICTED JET ENGINE EXHAUST VELOCITY CONTOURS

- LOW BREAKAWAY THRUST

MODEL 767-200, -200ER, -300 (CF6-80A, -80A2 ENGINES)

D6-58328

162 SEPTEMBER 2005

6.1.8 PREDICTED JET ENGINE EXHAUST VELOCITY CONTOURS

- LOW BREAKAWAY THRUST

MODEL 767-400ER (ALL ENGINES)

D6-58328

SEPTEMBER 2005 163

6.1.9 PREDICTED JET ENGINE EXHAUST VELOCITY CONTOURS

- HIGH BREAKAWAY THRUST

MODEL 767-200, -200ER, 300, -300ER, -300 FREIGHTER (ALL ENGINES)

D6-58328

164 SEPTEMBER 2005

6.1.10 PREDICTED JET ENGINE EXHAUST VELOCITY CONTOURS

- HIGH BREAKAWAY THRUST

MODEL 767-400ER (ALL ENGINES)

D6-58328

SEPTEMBER 2005 165

6.1.11 PREDICTED JET ENGINE EXHAUST VELOCITY CONTOURS

- TAKEOFF THRUST

MODEL 767-200, -200ER, -300 (JT9D-7R4D, -7R4E ENGINES)

D6-58328

166 SEPTEMBER 2005

6.1.12 PREDICTED JET ENGINE EXHAUST VELOCITY CONTOURS

- TAKEOFF THRUST

MODEL 767-200, -200ER, -300 (CF6-80A, -80A2 ENGINES)

D6-58328

SEPTEMBER 2005 167

6.1.13 PREDICTED JET ENGINE EXHAUST VELOCITY CONTOURS

- TAKEOFF THRUST

MODEL 767-300ER, -300 FREIGHTER (PW4056, CF6-80C2 ENGINES)

D6-58328

168 SEPTEMBER 2005

6.1.14 PREDICTED JET ENGINE EXHAUST VELOCITY CONTOURS

- TAKEOFF THRUST

MODEL 767-300, -300ER, -300 FREIGHTER (RB211-524 ENGINES)

D6-58328

SEPTEMBER 2005 169

6.1.15 PREDICTED JET ENGINE EXHAUST VELOCITY CONTOURS

- TAKEOFF THRUST

MODEL 767-400ER (ALL ENGINES)

D6-58328

170 SEPTEMBER 2005

6.1.16 PREDICTED JET ENGINE EXHAUST TEMPERATURE CONTOURS

- IDLE THRUST

MODEL 767—200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER (ALL ENGINES)

D6-58328

SEPTEMBER 2005 171

6.1.17 PREDICTED JET ENGINE EXHAUST TEMPERATURE CONTOURS

- BREAKAWAY THRUST

MODEL 767—200, -200ER, -300, -300ER, -300 FREIGHTER, -400ER (ALL ENGINES)

D6-58328

172 SEPTEMBER 2005

6.1.18 PREDICTED JET ENGINE EXHAUST TEMPERATURE CONTOURS

- TAKEOFF THRUST

MODEL 767-200, -200ER, -300 (JT9D-7R4E, -7R4E ENGINES)

D6-58328

SEPTEMBER 2005 173

6.1.19 PREDICTED JET ENGINE EXHAUST TEMPERATURE CONTOURS

- TAKEOFF THRUST

MODEL 767-200, -200ER, -300 (CF6-80A, -80A2 ENGINES)

D6-58328

174 SEPTEMBER 2005

6.1.20 PREDICTED JET ENGINE EXHAUST TEMPERATURE CONTOURS

- TAKEOFF THRUST

MODEL 767-300ER, -300 FREIGHTER (PW4000, CF6-80C2 ENGINES)

D6-58328

SEPTEMBER 2005 175

6.1.21 PREDICTED JET ENGINE EXHAUST TEMPERATURE CONTOURS

- TAKEOFF THRUST

MODEL 767-300, -300ER, -300 FREIGHTER (RB211-524 ENGINES)

D6-58328

176 SEPTEMBER 2005

6.1.22 PREDICTED JET ENGINE EXHAUST TEMPERATURE CONTOURS

- TAKEOFF THRUST

MODEL 767-400ER (ALL ENGINES)

D6-58328

SEPTEMBER 2005 177

6.2 Airport and Community Noise

Airport noise is of major concern to the airport and community planner. The airport is a major

element in the community's transportation system and, as such, is vital to its growth. However, the

airport must also be a good neighbor, and this can be accomplished only with proper planning. Since

aircraft noise extends beyond the boundaries of the airport, it is vital to consider the impact on

surrounding communities. Many means have been devised to provide the planner with a tool to

estimate the impact of airport operations. Too often they oversimplify noise to the point where the

results become erroneous. Noise is not a simple subject; therefore, there are no simple answers.

The cumulative noise contour is an effective tool. However, care must be exercised to ensure that

the contours, used correctly, estimate the noise resulting from aircraft operations conducted at an

airport.

The size and shape of the single-event contours, which are inputs into the cumulative noise contours,

are dependent upon numerous factors. They include the following:

1. Operational Factors

(a) Aircraft Weight - Aircraft weight is dependent on distance to be traveled, en route

winds, payload, and anticipated aircraft delay upon reaching the destination.

(b) Engine Power Settings-The rates of ascent and descent and the noise levels emitted

at the source are influenced by the power setting used.

influence noise.

D6-58328

178 SEPTEMBER 2005

2. Atmospheric Conditions-Sound Propagation

(a) Wind - With stronger headwinds, the aircraft can take off and climb more rapidly

relative to the ground. Also, winds can influence the distribution of noise in

surrounding communities.

(b) Temperature and Relative Humidity - The absorption of noise in the atmosphere

along the transmission path between the aircraft and the ground observer varies with

both temperature and relative humidity.

3. Surface Condition-Shielding, Extra Ground Attenuation (EGA)

(a) Terrain - If the ground slopes down after takeoff or up before landing, noise will be

reduced since the aircraft will be at a higher altitude above ground. Additionally,

hills, shrubs, trees, and large buildings can act as sound buffers.

D6-58328

SEPTEMBER 2005 179

All these factors can alter the shape and size of the contours appreciably. To demonstrate the effect

of some of these factors, estimated noise level contours for two different operating conditions are

shown below. These contours reflect a given noise level upon a ground level plane at runway

elevation.

Condition 1

Landing Takeoff

Maximum Structural Landing

Weight

Maximum Gross Takeoff Weight

10-knot Headwind Zero Wind

3o Approach 84 oF

84 oF Humidity 15%

Humidity 15%

Condition 2

Landing: Takeoff:

85% of Maximum Structural

Landing Weight

80% of Maximum Gross Takeoff

Weight

10-knot Headwind 10-knot Headwind

3o Approach 59 oF

59 oF Humidity 70%

Humidity 70%

D6-58328

180 SEPTEMBER 2005

As indicated from these data, the contour size varies substantially with operating and atmospheric

conditions. Most aircraft operations are, of course, conducted at less than maximum gross weights

because average flight distances are much shorter than maximum aircraft range capability and

average load factors are less than 100%. Therefore, in developing cumulative contours for planning

purposes, it is recommended that the airlines serving a particular city be contacted to provide

operational information.

In addition, there are no universally accepted methods for developing aircraft noise contours or for

relating the acceptability of specific zones to specific land uses. It is therefore expected that noise

contour data for particular aircraft and the impact assessment methodology will be changing. To

ensure that the best currently available information of this type is used in any planning study, it is

recommended that it be obtained directly from the Office of Environmental Quality in the Federal

Aviation Administration in Washington, D.C.

It should be noted that the contours shown herein are only for illustrating the impact of operating and

atmospheric conditions and do not represent the single-event contour of the family of aircraft

described in this document. It is expected that the cumulative contours will be developed as required

by planners using the data and methodology applicable to their specific study.

D6-58328 SEPTEMBER 2005 181

7.0 PAVEMENT DATA

7.1 General Information

7.2 Landing Gear Footprint

7.3 Maximum Pavement Loads

7.4 Landing Gear Loading on Pavement

7.5 Flexible Pavement Requirements - U.S. Army Corps of

Engineers Method S-77-1

7.6 Flexible Pavement Requirements - LCN Conversion

7.7 Rigid Pavement Requirements - Portland Cement

Association Design Method

7.8 Rigid Pavement Requirements - LCN Conversion

7.9 Rigid Pavement Requirements - FAA Method

7.10 ACN/PCN Reporting System - Flexible and Rigid Pavements

D6-58328

182 JUNE 2010

7.0 PAVEMENT DATA

7.1 General Information

A brief description of the pavement charts that follow will help in their use for airport planning. Each

airplane configuration is depicted with a minimum range of six loads imposed on the main landing

gear to aid in interpolation between the discrete values shown. All curves for any single chart

represent data based on rated loads and tire pressures considered normal and acceptable by current

aircraft tire manufacturer's standards. Tire pressures, where specifically designated on tables and

charts, are at values obtained under loaded conditions as certificated for commercial use.

Section 7.2 presents basic data on the landing gear footprint configuration, maximum design taxi

loads, and tire sizes and pressures.

Maximum pavement loads for certain critical conditions at the tire-to-ground interface are shown in

Section 7.3, with the tires having equal loads on the struts.

Pavement requirements for commercial airplanes are customarily derived from the static analysis of

loads imposed on the main landing gear struts. The chart in Section 7.4 is provided in order to

determine these loads throughout the stability limits of the airplane at rest on the pavement. These

main landing gear loads are used as the point of entry to the pavement design charts, interpolating

load values where necessary.

The flexible pavement design curves (Section 7.5) are based on procedures set forth in Instruction

Report No. S-77-1, "Procedures for Development of CBR Design Curves," dated June 1977, and as

modified according to the methods described in ICAO Aerodrome Design Manual, Part 3, Pavements,

2nd Edition, 1983, Section 1.1 (The ACN-PCN Method), and utilizing the alpha factors approved by

ICAO in October 2007. Instruction Report No. S-77-1 was prepared by the U.S. Army Corps of

Engineers Waterways Experiment Station, Soils and Pavements Laboratory, Vicksburg, Mississippi.

The line showing 10,000 coverages is used to calculate Aircraft Classification Number (ACN).

D6-58328 SEPTEMBER 2005 183

The following procedure is used to develop the curves, such as shown in Section 7.5:

1. Having established the scale for pavement depth at the bottom and the scale for CBR at the

top, an arbitrary line is drawn representing 6,000 annual departures.

2. Values of the aircraft gross weight are then plotted.

3. Additional annual departure lines are drawn based on the load lines of the aircraft gross

weights already established.

4. An additional line representing 10,000 coverages (used to calculate the flexible pavement

Aircraft Classification Number) is also placed.

All Load Classification Number (LCN) curves (Sections 7.6 and 7.8) have been developed from a

computer program based on data provided in International Civil Aviation Organization (ICAO)

document 9157-AN/901, Aerodrome Design Manual, Part 3, “Pavements”, First Edition, 1977. LCN

values are shown directly for parameters of weight on main landing gear, tire pressure, and radius of

relative stiffness (i) for rigid pavement or pavement thickness or depth factor (h) for flexible

pavement.

Rigid pavement design curves (Section 7.7) have been prepared with the Westergaard equation in

general accordance with the procedures outlined in the Design of Concrete Airport Pavement (1955

edition) by Robert G. Packard, published by the American Concrete Pavement Association, 3800

North Wilke Road, Arlington Heights, Illinois 60004-1268. These curves are modified to the format

described in the Portland Cement Association publication XP6705-2, Computer Program for Airport

Pavement Design (Program PDILB), 1968, by Robert G. Packard.

The following procedure is used to develop the rigid pavement design curves shown in

Section 7.7:

1. Having established the scale for pavement thickness to the left and the scale for allowable

working stress to the right, an arbitrary load line is drawn representing the main landing gear

maximum weight to be shown.

2. Values of the subgrade modulus (k) are then plotted.

3. Additional load lines for the incremental values of weight on the main landing gear are drawn

on the basis of the curve for k = 300, already established.

D6-58328

184 SEPTEMBER 2005

The ACN/PCN system (Section 7.10) as referenced in ICAO Annex 14, "Aerodromes," First Edition,

July 1990, provides a standardized international airplane/pavement rating system replacing the

various S, T, TT, LCN, AUW, ISWL, etc., rating systems used throughout the world. ACN is the

Aircraft Classification Number and PCN is the Pavement Classification Number. An aircraft having

an ACN equal to or less than the PCN can operate on the pavement subject to any limitation on the

tire pressure. Numerically, the ACN is two times the derived single-wheel load expressed in

thousands of kilograms, where the derived single wheel load is defined as the load on a single tire

inflated to 181 psi (1.25 MPa) that would have the same pavement requirements as the aircraft.

Computationally, the ACN/PCN system uses the PCA program PDILB for rigid pavements and S-77-

1 for flexible pavements to calculate ACN values. The method of pavement evaluation is left up to

the airport with the results of their evaluation presented as follows:

PCN PAVEMENT

TYPE SUBGRADE

CATEGORY TIRE PRESSURE

CATEGORY EVALUATION

METHOD

R = Rigid A = High W = No Limit T = Technical

F = Flexible B = Medium X = To 254 psi (1.75 MPa) U = Using Aircraft

C = Low Y = To 181 psi (1.25 MPa)

D = Ultra Low Z = To 73 psi (0.5 MPa)

Section 7.10.1 shows the aircraft ACN values for flexible pavements. The four subgrade categories

are:

Code A - High Strength - CBR 15

Code B - Medium Strength - CBR 10

Code C - Low Strength - CBR 6

Code D - Ultra Low Strength - CBR 3

Section 7.10.2 shows the aircraft ACN values for rigid pavements. The four subgrade categories are:

Code A - High Strength, k = 550 pci (150 MN/m3)

Code B - Medium Strength, k = 300 pci (80 MN/m3)

Code C - Low Strength, k = 150 pci (40 MN/m3)

Code D - Ultra Low Strength, k = 75 pci (20 MN/m3)

D6-58328 SEPTEMBER 2005 185

UNITS MODEL 767-200 MODEL 767-200ER

LB 284,000 – 317,000 337,000 – 347,000 352,200 381,000 388,000 – 396,000

MAXIMUM DESIGN

TAXI WEIGHT KG 128,820 – 143,788 152,861 – 157,397 159,755 172,819 175,994 - 179,623

PERCENT OF

WEIGHT ON MAIN

GEAR

SEE SECTION

7.4.1 SEE SECTION 7.4.2 SEE SECTION 7.4.3

NOSE GEAR

TIRE SIZE H37 x 14-15 22PR H37 x 14-15 22PR

PSI 145 155 155 180 185 NOSE GEAR

TIRE PRESSURE KG/CM2 10.19 10.90 10.90 12.66 13.01

MAIN GEAR

TIRE SIZE H45 x 17-20 26PR

(1) H46 x 18-20 28PR H46 x 18-20 28PR H46 x 18-20 32PR

PSI 190 (1) 175 (2) 183 (2) 190 MAIN GEAR

TIRE PRESSURE KG/CM2 13.36 (1) 12.30 (2) 12.87 (2) 13.36

NOTES:

(1) OPTIONAL TIRE: H46 x 18-20 26PR AT 175 PSI (12.30 KG/SQ CM) OR

H46 x 18-20 26PR H/D AT 155 PSI (10.9 KG/SQ CM) OR 175 PSI (12.30 KG/SQ CM)

(2) OPTIONAL TIRE PRESSURE: 190 PSI (13.36 KG/SQ CM)

7.2.1 LANDING GEAR FOOTPRINT

MODEL 767-200, -200ER

D6-58328

186 SEPTEMBER 2005

UNITS MODEL 767-300 MODEL 767-300ER MODEL 767-300ER,

-300 FREIGHTER

LB 317,000 - 340,000 352,000 381,000 388,000 401,000 – 413,000

MAXIMUM DESIGN

TAXI WEIGHT KG 143,789 – 154,221 159,665 172,820 175,994 181,908 – 187,339

PERCENT OF

WEIGHT ON MAIN

GEAR

SEE SECTION 7.4.4 SEE SECTION 7.4.5 SEE SECTION

7.4.6

NOSE GEAR

TIRE SIZE H37 x 14-15 22PR H37 x 14-15 22PR H37 x 14-15 22PR

PSI 150 145 150 165 170 NOSE GEAR

TIRE PRESSURE KG/CM2 10.55 10.19 10.55 11.60 11.95

MAIN GEAR

TIRE SIZE H46 x 18-20 28PR H46 x 18-20

28PR H46 x 18-20

32PR H46 x 18-20 32PR

PSI 175 (1) 195 175 190 200 MAIN GEAR

TIRE PRESSURE KG/CM2 12.30 (1) 13.71 12.30 13.36 14.06

NOTES:

(1) OPTIONAL TIRE PRESSURE: 190 PSI (13.36 KG/SQ CM)

7.2.2 LANDING GEAR FOOTPRINT

MODEL 767-300, -300ER, -300 FREIGHTER

D6-58328 SEPTEMBER 2005 187

UNITS 767-400ER

MAXIMUM DESIGN LB 451,000

TAXI WEIGHT KG 204,570

PERCENT OF WEIGHT ON

MAIN GEAR

SEE SECTION 7.4

NOSE GEAR

TIRE SIZE IN. H37 x 14 - 15 24PR

NOSE GEAR PSI 185

TIRE PRESSURE KG/CM2 13.01

MAIN GEAR

TIRE SIZE IN. 50 x 20 R22 32 PR

MAIN GEAR PSI 215

TIRE PRESSURE KG/CM2 15.11

7.2.3 LANDING GEAR FOOTPRINT

MODEL 767-400ER

D6-58328

188 SEPTEMBER 2005

V (NG) = MAXIMUM VERTICAL NOSE GEAR GROUND LOAD AT MOST FORWARD CENTER OF GRAVITY

V (MG) = MAXIMUM VERTICAL MAIN GEAR GROUND LOAD AT MOST AFT CENTER OF GRAVITY

H = MAXIMUM HORIZONTAL GROUND LOAD FROM BRAKING

NOTE: ALL LOADS CALCULATED USING AIRPLANE MAXIMUM DESIGN TAXI WEIGHT

V (NG) V (MG) PER

STRUT H PER STRUT

MODEL

UNIT

MAXIMUM

DESIGN

TAXI

WEIGHT

STATIC

AT MOST

FWD

C.G.

STATIC +

BRAKING 10

FT/SEC2

DECEL

MAX LOAD

AT STATIC

AFT C.G.

STEADY

BRAKING 10

FT/SEC2

DECEL

INSTANTANEOUS

BRAKING

(u= 0.8)

767-200 LB 284,000 39,100 56,500 133,300 44,100 106,600

KG 128,821 17,736 25,628 60,464 20,003 48,353

767-200 LB 302,000 39,900 58,600 141,700 46,900 113,400

KG 136,985 18,098 26,581 64,274 21,274 51,437

767-200 LB 312,000 40,200 59,700 146,400 48,400 117,100

KG 141,521 18,234 27,080 66,406 21,954 53,116

767-200 LB 317,000 40,600 60,400 146,300 49,200 117,000

KG 143,789 18,416 27,397 66,361 22,317 53,070

767-200ER LB 337,000 42,700 63,800 158,100 52,300 126,500

KG 152,861 19,368 28,939 71,713 23,723 57,380

767-200ER LB 347,000 43,200 65,200 160,700 53,900 128,600

KG 157,397 19,595 29,574 72,892 24,449 58,332

LB 352,200 43,300 65,100 162,200 54,700 129,800

767-200ER

KG 159,756 19,641 29,529 73,573 24,812 58,876

767-200ER LB 381,000 51,500 74,900 178,800 59,200 143,000

KG 172,819 23,360 33,974 81,103 26,853 64,864

767-200ER LB 388,000 52,400 76,100 180,000 60,200 144,000

KG 175,994 23,768 34,518 81,647 27,306 65,317

LB 396,000 44,640 70,510 179,810 61,500 143,850

767-200ER

KG 179,623 20,248 31,983 81,561 27,896 65,249

7.3.1 MAXIMUM PAVEMENT LOADS

MODEL 767-200, -200ER

D6-58328 SEPTEMBER 2005 189

V (NG) = MAXIMUM VERTICAL NOSE GEAR GROUND LOAD AT MOST FORWARD CENTER OF GRAVITY

V (MG) = MAXIMUM VERTICAL MAIN GEAR GROUND LOAD AT MOST AFT CENTER OF GRAVITY

H = MAXIMUM HORIZONTAL GROUND LOAD FROM BRAKING

NOTE: ALL LOADS CALCULATED USING AIRPLANE MAXIMUM DESIGN TAXI WEIGHT

V (NG) V (MG) PER

STRUT H PER STRUT

MODEL

UNIT

MAXIMUM

DESIGN

TAXI

WEIGHT

STATIC

AT MOST

FWD

C.G.

STATIC +

BRAKING 10

FT/SEC2

DECEL

MAX LOAD

AT STATIC

AFT C.G.

STEADY

BRAKING 10

FT/SEC2

DECEL

INSTANTANEOUS

BRAKING

(u= 0.8)

767-300 LB 317,200 41,100 58,300 150,600 49,300 120,500

KG 143,880 18,643 26,444 68,311 22,362 54,658

767-300 LB 347,000 41,000 59,600 160,100 53,900 128,100

KG 157,397 18,597 27,034 72,620 24,449 58,105

767-300 LB 352,000 41,000 60,000 162,400 54,700 129,900

KG 159,665 18,597 27,216 73,664 24,812 58,922

767-300ER LB 381,000 46,600 66,800 177,900 59,200 142,300

KG 172,819 21,137 30,300 80,694 26,853 64,546

767-300ER LB 388,000 40,200 60,700 180,100 60,200 144,100

KG 175,994 18,234 27,533 81,692 27,306 65,363

LB 401,000 48,200 69,500 186,300 62,300 149,100

767-300ER,

FREIGHTER KG 181,891 21,863 31,525 84,504 28,259 67,631

LB 409,000 48,200 69,900 188,200 63,500 150,600

767-300ER,

FREIGHTER KG 185,520 21,863 31,706 85,366 28,803 68,311

LB 413,000 44,330 67,660 190,800 64,140 152,640

767-300ER,

FREIGHTER KG 187,334 20,108 30,690 86,546 29,093 69,237

7.3.2 MAXIMUM PAVEMENT LOADS

MODEL 767-300, -300ER, -300 FREIGHTER

D6-58328

190 SEPTEMBER 2005

V (NG) = MAXIMUM VERTICAL NOSE GEAR GROUND LOAD AT MOST FORWARD CENTER OF GRAVITY

V (MG) = MAXIMUM VERTICAL MAIN GEAR GROUND LOAD AT MOST AFT CENTER OF GRAVITY

H = MAXIMUM HORIZONTAL GROUND LOAD FROM BRAKING

NOTE: ALL LOADS CALCULATED USING AIRPLANE MAXIMUM DESIGN TAXI WEIGHT

V (NG) V (MG) PER

STRUT H PER STRUT

MODEL

UNIT

MAXIMUM

DESIGN

TAXI

WEIGHT

STATIC

AT MOST

FWD

C.G.

STATIC +

BRAKING 10

FT/SEC2

DECEL

MAX LOAD

AT STATIC

AFT C.G.

STEADY

BRAKING

FT/SEC2

DECEL

AT INSTANTANEOUS

BRAKING

(u= 0.8)

767-400ER

LB 451,000 37,600 59, 650 211,850 70,050 169,500

KG 204,570 17,055 27,057 96,093 31,774 76,884

7.3.3 MAXIMUM PAVEMENT LOADS

MODEL 767-400ER

D6-58328 SEPTEMBER 2005 191

7.4.1 LANDING GEAR LOADING ON PAVEMENT

MODEL 767-200 AT 284,000 TO 317,000 LB (128,820 TO 143,789 KG) MTW

D6-58328

192 SEPTEMBER 2005

7.4.2 LANDING GEAR LOADING ON PAVEMENT

MODEL 767-200, -200ER AT 337,000 TO 352,200 LB (152,860 TO 159,755 KG) MTW

D6-58328 SEPTEMBER 2005 193

7.4.3 LANDING GEAR LOADING ON PAVEMENT

MODEL 767-200ER AT 381,000 TO 396,000 LB (172,819TO 179,623 KG) MTW

D6-58328

194 SEPTEMBER 2005

7.4.4 LANDING GEAR LOADING ON PAVEMENT

MODEL 767-300 AT 317,200 TO 352,000 LB (143,890 TO 159,665 KG) MTW

D6-58328 SEPTEMBER 2005 195

7.4.5 LANDING GEAR LOADING ON PAVEMENT

MODEL 767-300ER AT 381,000 TO 388,000 LB (172,819 TO 175,994 KG) MTW

D6-58328

196 SEPTEMBER 2005

7.4.6 LANDING GEAR LOADING ON PAVEMENT

MODEL 767-300ER, -300 FREIGHTER AT 401,000 TO 413,000 LB (181,908 TO 187,334 KG) MTW

D6-58328 SEPTEMBER 2005 197

7.4.7 LANDING GEAR LOADING ON PAVEMENT

MODEL 767-400ER

D6-58328

198 SEPTEMBER 2005

7.5 Flexible Pavement Requirements - U.S. Army Corps of Engineers Method

(S-77-1)

The following flexible-pavement design chart presents the data of six incremental main-gear loads at

the minimum tire pressure required at the maximum design taxi weight.

In the example shown in 7.5.1, for a CBR of 30 and an annual departure level of 3,000, the required

flexible pavement thickness for an airplane with a main gear loading of 376,300 pounds is 12.0 inches.

The line showing 10,000 coverages is used for ACN calculations (see Section 7.10).

The FAA design method uses a similar procedure using total airplane weight instead of weight on the

main landing gears. The equivalent main gear loads for a given airplane weight could be calculated

from Section 7.4.

D6-58328 SEPTEMBER 2005 199

7.5.1 FLEXIBLE PAVEMENT REQUIREMENTS - U.S. ARMY CORPS OF ENGINEERS DESIGN

METHOD (S-77-1)

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER

D6-58328

200 SEPTEMBER 2005

7.5.2 FLEXIBLE PAVEMENT REQUIREMENTS - U.S. ARMY CORPS OF ENGINEERS DESIGN

METHOD (S-77-1)

MODEL 767-400ER

D6-58328 SEPTEMBER 2005 201

7.6 Flexible Pavement Requirements - LCN Method

To determine the airplane weight that can be accommodated on a particular flexible pavement, both

the Load Classification Number (LCN) of the pavement and the thickness must be known.

In the example shown in 7.6.1, flexible pavement thickness is shown at 30 in. with an LCN of 75.

For these conditions, the apparent maximum allowable weight permissible on the main landing gear is

250,000 lb for an airplane with 200-psi main gear tires.

Note: If the resultant aircraft LCN is not more that 10% above the published pavement LCN, the

bearing strength of the pavement can be considered sufficient for unlimited use by the

airplane. The figure 10% has been chosen as representing the lowest degree of variation in

LCN that is significant (reference: ICAO Aerodrome Manual, Part 2, "Aerodrome Physical

Characteristics," Chapter 4, Paragraph 4.1.5.7v, 2nd Edition dated 1965).

D6-58328

202 SEPTEMBER 2005

7.6.1 FLEXIBLE PAVEMENT REQUIREMENTS - LCN METHOD

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER

D6-58328 SEPTEMBER 2005 203

7.6.2 FLEXIBLE PAVEMENT REQUIREMENTS - LCN METHOD

MODEL 767-400ER

D6-58328

204 SEPTEMBER 2005

7.7 Rigid Pavement Requirements - Portland Cement Association Design Method

The Portland Cement Association method of calculating rigid pavement requirements is based on the

computerized version of "Design of Concrete Airport Pavement" (Portland Cement Association,

1955) as described in XP6705-2, "Computer Program for Airport Pavement Design" by Robert G.

Packard, Portland Cement Association, 1968.

The following rigid pavement design chart presents the data for six incremental main gear loads at the

minimum tire pressure required at the maximum design taxi weight.

In the example shown in 7.7.1, for an allowable working stress of 550 psi, a main gear load of

300,000 lb, and a subgrade strength (k) of 300, the required rigid pavement thickness is 9.4 in.

D6-58328 SEPTEMBER 2005 205

7.7.1 RIGID PAVEMENT REQUIREMENTS - PORTLAND CEMENT ASSOCIATION DESIGN

METHOD

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER

D6-58328

206 SEPTEMBER 2005

7.7.2 RIGID PAVEMENT REQUIREMENTS - PORTLAND CEMENT ASSOCIATION DESIGN

METHOD

MODEL 767-400ER

D6-58328 SEPTEMBER 2005 207

7.8 Rigid Pavement Requirements - LCN Conversion

To determine the airplane weight that can be accommodated on a particular rigid pavement, both the

LCN of the pavement and the radius of relative stiffness ( ) of the pavement must be known.

In the example shown in 7.8.2, for a rigid pavement with a radius of relative stiffness of 60 with an

LCN of 80, the apparent maximum allowable weight permissible on the main landing gear is 250,000

lb for an airplane with 200-psi main tires.

Note: If the resultant aircraft LCN is not more that 10% above the published pavement LCN, the

bearing strength of the pavement can be considered sufficient for unlimited use by the

airplane. The figure 10% has been chosen as representing the lowest degree of variation in

LCN that is significant (reference: ICAO Aerodrome Manual, Part 2, "Aerodrome Physical

Characteristics," Chapter 4, Paragraph 4.1.5.7v, 2nd Edition dated 1965).

D6-58328

208 SEPTEMBER 2005

RADIUS OF RELATIVE STIFFNESS ()

VALUES IN INCHES

= 4Ed3

12(1-µ2)k = 24.1652 4d3

WHERE: E = YOUNG'S MODULUS OF ELASTICITY = 4 x 106 psi

k = SUBGRADE MODULUS, LB PER CU IN

d = RIGID PAVEMENT THICKNESS, IN

µ = POISSON'S RATIO = 0.15

k = k = k = k = k = k = k = k = k = k =

d 75 100 150 200 250 300 350 400 500 550

6.0 31.48 29.29 26.47 24.63 23.30 22.26 21.42 20.71 19.59 19.13

6.5 33.42 31.10 28.11 26.16 24.74 23.63 22.74 21.99 20.80 20.31

7.0 35.33 32.88 29.71 27.65 26.15 24.99 24.04 23.25 21.99 21.47

7.5 37.21 34.63 31.29 29.12 27.54 26.31 25.32 24.49 23.16 22.61

8.0 39.06 36.35 32.84 30.56 28.91 27.62 26.57 25.70 24.31 23.73

8.5 40.87 38.04 34.37 31.99 30.25 28.90 27.81 26.90 25.44 24.84

9.0 42.66 39.70 35.88 33.39 31.57 30.17 29.03 28.07 26.55 25.93

9.5 44.43 41.35 37.36 34.77 32.88 31.42 30.23 29.24 27.65 27.00

10.0 46.17 42.97 38.83 36.13 34.17 32.65 31.41 30.38 28.73 28.06

10.5 47.89 44.57 40.27 37.48 35.44 33.87 32.58 31.52 29.81 29.10

11.0 49.59 46.15 41.70 38.81 36.70 35.07 33.74 32.63 30.86 30.14

11.5 51.27 47.72 43.12 40.12 37.95 36.26 34.89 33.74 31.91 31.16

12.0 52.94 49.26 44.51 41.43 39.18 37.43 36.02 34.83 32.94 32.17

12.5 54.58 50.80 45.90 42.71 40.40 38.60 37.14 35.92 33.97 33.17

13.0 56.21 52.31 47.27 43.99 41.60 39.75 38.25 36.99 34.98 34.16

13.5 57.83 53.81 48.63 45.25 42.80 40.89 39.34 38.05 35.99 35.14

14.0 59.43 55.30 49.97 46.50 43.98 42.02 40.43 39.10 36.98 36.11

14.5 61.01 56.78 51.30 47.74 45.15 43.14 41.51 40.15 37.97 37.07

15.0 62.58 58.24 52.62 48.97 46.32 44.25 42.58 41.18 38.95 38.03

15.5 64.14 59.69 53.93 50.19 47.47 45.35 43.64 42.21 39.92 38.98

16.0 65.69 61.13 55.23 51.40 48.61 46.45 44.69 43.22 40.88 39.92

16.5 67.22 62.55 56.52 52.60 49.75 47.53 45.73 44.23 41.83 40.85

17.0 68.74 63.97 57.80 53.79 50.87 48.61 46.77 45.23 42.78 41.77

17.5 70.25 65.38 59.07 54.97 51.99 49.68 47.80 46.23 43.72 42.69

18.0 71.75 66.77 60.34 56.15 53.10 50.74 48.82 47.22 44.65 43.60

19.0 74.72 69.54 62.83 58.47 55.30 52.84 50.84 49.17 46.50 45.41

20.0 77.65 72.26 65.30 60.77 57.47 54.91 52.83 51.10 48.33 47.19

21.0 80.55 74.96 67.73 63.03 59.61 56.95 54.80 53.00 50.13 48.95

22.0 83.41 77.62 70.14 65.27 61.73 58.98 56.75 54.88 51.91 50.68

23.0 86.23 80.25 72.51 67.48 63.82 60.98 58.67 56.74 53.67 52.40

24.0 89.03 82.85 74.86 69.67 65.89 62.95 60.57 58.58 55.41 54.10

25.0 91.80 85.43 77.19 71.84 67.94 64.91 62.46 60.41 57.13 55.78

7.8.1 RADIUS OF RELATIVE STIFFNESS

(REFERENCE: PORTLAND CEMENT ASSOCIATION)

D6-58328 SEPTEMBER 2005 209

7.8.2 RIGID PAVEMENT REQUIREMENTS - LCN CONVERSION

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER

D6-58328

210 SEPTEMBER 2005

7.8.3 RIGID PAVEMENT REQUIREMENTS - LCN CONVERSION

MODEL 767-400ER

D6-58328 SEPTEMBER 2005 211

7.9 Rigid Pavement Requirements - FAA Design Method

The following rigid-pavement design chart presents data on six incremental main gear loads at the

minimum tire pressure required at the maximum design taxi weight.

In the example shown in 7.9.1, the pavement flexural strength is shown at 700 psi, the subgrade

strength is shown at k = 300, and the annual departure level is 6,000. For these conditions, the

required rigid pavement thickness for an airplane with a main gear loading of 350,000 pounds is 12.4

inches.

D6-58328

212 SEPTEMBER 2005

7.9.1 RIGID PAVEMENT REQUIREMENTS - FAA METHOD

MODEL 767-200, -200ER, -300, -300ER, -300 FREIGHTER

D6-58328 SEPTEMBER 2005 213

7.9.2 RIGID PAVEMENT REQUIREMENTS - FAA METHOD

MODEL 767-400ER

D6-58328

214 JUNE 2010

7.10 ACN/PCN Reporting System - Flexible and Rigid Pavements

To determine the ACN of an aircraft on flexible or rigid pavement, both the aircraft gross weight and

the subgrade strength category must be known. In the chart in 7.10.1, for an aircraft with gross

weight of 260,000 lb on a low subgrade strength (Code C), the flexible pavement ACN is 32.4.

Referring to 7.10.6, the same aircraft, the same gross weight, and on a low subgrade rigid pavement

has an ACN of 35.5.

Note: An aircraft with an ACN equal to or less that the reported PCN can operate on that pavement

subject to any limitations on the tire pressure. (Ref.: Ammendment 35 to ICAO Annex 14

Aerodrome, Eighth Edition, March 1983.)

The following table provides ACN data in tabular format similar to the one used by ICAO in the

“Aerodrome Design Manual Part 3, Pavements.” If the ACN for an intermediate weight between taxi

weight and empty fuel weight of the aircraft is required, Figures 7.10.1 through 7.10.10 should be

consulted.

ACN FOR RIGID PAVEMENT

SUBGRADES – MN/m3 ACN FOR FLEXIBLE PAVEMENT

SUBGRADES – CBR

AIRCRAFT

TYPE

MAXIMUM TAXI

WEIGHT

MINIMUM

WEIGHT (1)

LB (KG)

LOAD

ONE

MAIN

GEAR

LEG

(%)

TIRE

PRESSURE

PSI (MPa)

HIGH

150

MEDIUM

LOW

ULTRA

LOW

HIGH

MEDIUM

LOW

ULTRA

LOW

767-200 317,000(143,787)

181,000(82,100)

46.15 190 (1.31) 39

767-200ER 396,000(179,623)

182,000(82,600)

45.41 190 (1.31) 44

767-300 352,000(159,665)

190,000(86,200)

46.14

195(1.34) 40

767-300ER

737-300F 413,000(187,334)

198,000(89,811)

46.2 200(1.38) 40

767-400ER 451,000(204,570)

229,000(103,900) 46.98 215(1.48) 58

24 68

27 80

32 91

37 56

24 63

26 77

29 99

(1) Minimum weight used solely as a baseline for ACN curve generation.

D6-58328 JUNE 2010 215

7.10.1 AIRCRAFT CLASSIFICATION NUMBER - FLEXIBLE PAVEMENT

MODEL 767-200

D6-58328

216 JUNE 2010

7.10.2 AIRCRAFT CLASSIFICATION NUMBER - FLEXIBLE PAVEMENT

MODEL 767--200ER

D6-58328 JUNE 2010 217

7.10.3 AIRCRAFT CLASSIFICATION NUMBER - FLEXIBLE PAVEMENT

MODEL 767-300

D6-58328

218 JUNE 2010

7.10.4 AIRCRAFT CLASSIFICATION NUMBER - FLEXIBLE PAVEMENT

MODEL 767-300ER, -300 FREIGHTER

D6-58328 JUNE 2010 219

7.10.5 AIRCRAFT CLASSIFICATION NUMBER - FLEXIBLE PAVEMENT

MODEL 767-400ER

D6-58328

220 SEPTEMBER 2005

7.10.6 AIRCRAFT CLASSIFICATION NUMBER - RIGID PAVEMENT

MODEL 767-200

D6-58328 SEPTEMBER 2005 221

7.10.7 AIRCRAFT CLASSIFICATION NUMBER - RIGID PAVEMENT

MODEL 767-200ER

D6-58328

222 SEPTEMBER 2005

7.10.8 AIRCRAFT CLASSIFICATION NUMBER - RIGID PAVEMENT

MODEL 767-300

D6-58328 SEPTEMBER 2005 223

7.10.9 AIRCRAFT CLASSIFICATION NUMBER - RIGID PAVEMENT

MODEL 767-300ER, -300 FREIGHTER

D6-58328

224 SEPTEMBER 2005

7.10.10 AIRCRAFT CLASSIFICATION NUMBER - RIGID PAVEMENT

MODEL 767-400ER

D6-58328

SEPTEMBER 2005 225

8.0 FUTURE 767 DERIVATIVE AIRPLANES

D6-58328

226 SEPTEMBER 2005

8.0 FUTURE 767 DERIVATIVE AIRPLANES

Several derivatives are being studied to provide additional capabilities of the 767 family of

airplanes. Future growth versions could require additional passenger or cargo capacity or

increased range or both. Whether these growth versions could be built would depend entirely on

airline requirements. In any event, impact on airport facilities will be a consideration in the

configuration and design.

D6-58328 SEPTEMBER 2005 227

9.0 SCALED 767 DRAWINGS

9.1 – 9.5 Model 767-200, -200ER

9.6 – 9.10 Model 767-300, -300ER

9.11 – 9.15 Model 767-300 Freighter

9.16 – 9.20 Model 767-400ER

D6-58328

228 SEPTEMBER 2005

9.0 SCALED DRAWINGS

The drawings in the following pages show airplane plan view drawings, drawn to approximate scale

as noted. The drawings may not come out to exact scale when printed or copied from this document.

Printing scale should be adjusted when attempting to reproduce these drawings. Three-view drawing

files of the 767-200, -200ER, -300, -300ER, -300 Freighter, -400ER, along with other Boeing airplane

models, can be downloaded from the following website:

http://www.boeing.com/airports