PDF Panasonic KX T336 System Ref Vol 3
KX-T 336 System Ref Suppliment To Vol 1 & 2 KX-T 336 System Ref Suppliment To Vol 1 & 2
KX-T336 System Ref Suppliment To Vol 12 KX-T336_System_Ref_Suppliment_To_Vol_1_2 Panasonic KX-T336 Analog System - Telecomuserguides.com
User Manual: PDF T E X T F I L E S
Open the PDF directly: View PDF .
Page Count: 872
Download | |
Open PDF In Browser | View PDF |
STOP!!! READ THIS FIRST I Before upgrading the KX-T336 to the 12.00 revision that is included with this kit be sure to read and understand the WP (version up ) command that is detailed on I additional page 15-G-3. This command is used to initialize the RAM area of the newly added system memory while keeping the current settings intact. . , 1NSTAf;wLTION INSTRUCTIONS FOR W-T336 EPROMS mt The following procedures should be followed in the exact order in which they are written. If these instructions are not followed, permanent damage to the RMSS could result. NOTR: It is recommended that before upgrading the EMUS that all programming be saved (section 16) since the system may return to the default program during this procedure. Materials needed to complete this software change: 4 l Eprom(s) 1 l IC extraction tool . 1) 2) 3) 4) 5) . 6) ‘1 8) 9) 10) 11) 12) 13) 14) 1% 16) 17) Turn the power switch on all KX-T336 cabinets to the OPF position and disconnect all power cords from the AC outlets. If any optional system battery adapters (RX-A26) are installed, set their power switches to the off position. Remove the front cwer by turnin g the key counterclockwise and then pulling the cover forward. Locate the aCPUa card installed in slot BS 1 and remove the guide plate from the upper front side (if installed) to allow access to the TPU” card. Set the 'W&e" switch on the "CPU" card to position 0 and set the "synm" switch to 0. Before removing the-"CPU", be sure to be wearing an antistatic wristband or to ground yourself. Remove the "CPU" card which is inserted into the slot marked "CPU* by lifting both latches on the "CPU" card and/z&en pulling the card out. Place the "CPU" card on a flat work surface and locate IC 11, 12., 13 and'14 (see figure 1). Gently remove the chips from the sockets using a IC extraction tool. Install each new IC in the proper socket on the *CPU" card making sure that they are in the correct position and that all the pins remain straight. Install the "CPU" card. Install the PCB guide plate. Connect all power cords to the AC.outlets. Turn the power switches to the ON positions and push the reset button. Wait until system returns to the on-line mode. Turn the power switches on all optional system battery adapters (~~0~26) to the ON position. Verify that all programming is retained or Load system parameters as instructed in section 16. Page 1 of 2 - Supplement Manual for KX-A220 @ manual This Supplement Manual is issued to provide information on new features (described on the following pages) which have been added to the KX-T336 System after the KX-A220 @ manual was printed. . KX-A220 @ manual consists of: Vol. 1 (PQQX6483XA) Vol. 2 (PQQX6485XA) Notice The KX-T336100 with the mark @ provides new features as described below. Location of the mark @ The mark @ is attached to the back of the unit as shown below. * New Features The KX-T336 System provides the following new features that enhance system operation. Available from software Version 12.00 (CPU card ROM: Y251L - Y254L) and above. l l l l l l l Call Forwarding - Follow Me (CFM command) DISA/AGC Tone Detection Mode (TDM command) Limited Call Duration (LCD command) Ringback Tone while Transfer (WS3 command) Screened Cal! Transfer to Trunk by SLT (WS3 command) Tie Lines T-l Interface (KX-T96187) 2 Please replace the following pages in the old version with newly issued revised version attached. Newly issued pages are marked as “(70695)“. Vol.1 Old Version New Version Page (Section 1) Cover Page (Section 1) Cover l-1 (60395) l-l (70695)M 1-2 l-2 (70695)M 1 -A-l l-A-1 1 -A-4 l-A-4 1 -A-5 (60395) 1 -A-5 (70695)M 1 -A-6 1 -A-6 (70695)M 1 -B-l (60395) 1 -El (70695)M l-B-l-1 (70695)M blank l-D-3 1 -D-3 1 -E-l (30393) 1 -E-l (70695)M 1 -E-2 (30393) 1 -E-2 (70695)M l-E-3 1 -E-3 1 -E-4 (E) 1 -E-4 (E) 1 -E-5 (60395) 1 -E-5 (70695)M l-E-6 (50195) (E) l-E-6 (70695)(E)M 1 -E-7 1 -E-7 (70695)M 1 -E-8 (50195) 1 -E-8 (70695)M 1 -E-9 1 -E-9 (70695)M 1-E-10 (E) 1 -E-l 0 (70695)(E)M l-E-11 (E) l-E-11 (70695)(E)M 1 -E-l 2 (70695)M blank 2-2 (60395) 2-2 (70695)M 2-A-l 2-A-l 3 Old Version New - Version 2-C-28-l (70695)M 2-C-28-2 (70695)M 2-C-28-3 (70695)M 2-C-28-4 (70695)M 2-C-28-5 (70695)M blank Insert these sheets after page 2-C-28. 3-2 (60395) 3-2 (70695)M 3-3 (60395) 3-3 (70695)M 3-B-2 3-B-2 3-B-3 (60395) 3-B-3 (70695)M 3-B-4 (30393) 3-B-4 (70695) 3-B-5 3-B-4-1 (70695) blank 3-B-5 (70695) 3-B-7 2 3-B-12 3-B-l 3 3-B-l 3 (70695) 3-B-19 3-B-l 9 3-B-20 3-B-20 (70695)M 4 . Old Version 3-F-66 New Version (40993) 3-F-66 (40993) blank 3-F-67 (70695)M 3-F-68 (70695) 3-F-69 (70695) 3-F-70 (70695) 3-F-71 (70695)M 3-F-72 (70695) 3-F-73 (70695) 3-F-74 (70695) 3-F-75 (70695) 3-F-76 (70695) 3-F-77 (70695) 3-F-78 (70695) 3-F-79 (70695) 3-F-80 (70695) 3-F-81 (70695) 3-F-82 (70695) 3-F-83 (70695) 3-F-84 (70695)M 3-F-85 (70695)M 3-F-86 (70695)M blank 4-2 4-2 4-3 (30393) 4-3 (70695) 4-F-18 4-F- 18 (70695) 4-F-l 9 4-F-l 9 4-F-20 4-F-20 4-G-l 4-F-21 (70695) blank 4-G-l 5-2 (30393) 5-2 (70695) 5-A-l (60395) 5-A-l (70695) 5 Old Version New Version 5-D-l 5-D-l (70695) 5-D-2 5-D-l -1 (70695) 5-D-3 (50195) 5-D-2 (70695) 5-D-3-l 5-D-3 (70695) (21292) 5-D-3-Z (40993) 5-D-3-l (70695) 5-D-4 (21292) 5-D-3-2 (70695) 5-D-3-3 (70695) 5-D-4 (70695) 5-D-l 5 (21292) 5-D-l 5 (21292) 5-D-l 6 5-D-l 6 (70695) - 5-D-l 9 (70695) blank insert this sheet after page 5-D-l 8. 5-E-l 5-E-l (70695) 5-E-2 5-E-l-l (70695) . blank 5-E-2 (70695) . Vol.2 Old Version New Version 7-c-3 7-c-3 7-C-4 (60395) 7-C-4 (70695)M 7-C-5 (60395) 7-C-5 (70695)M 7-C-6 7-C-6 8-D-l (50195) 8-D-l (70695)M 8-D-2 8-D-2 8-G-l (60395) 8-G-l (70695)M blank blank Cover page (Section 9) Cover page (Section 9) 9-1 9-1 (70695)M 9-2 (60395) 9-2 (70695)M 9-3 (60395) 9-3 (70695)M 9-A-l 9-A-l 9-B-l (60395) 9-B-l (70695)M 9-c-2 9-c-2 9-C-3 9-C-3 (70695)M (60395) 9-c-4 9-c-5 9-C-4 (30393) - (70695)M 9-C-5 (70695) 9-C-8 (70695) blank Insert this sheet after page 9-C-7. 9-D-l (60395) 9-D-l (70695)M 9-D-2 (60395) 9-D-2 (60395)M 9-D-3 (60395) 9-D-3 (7069’5)M 9-D-4 (60395) 9-D-4 9-D-7 9-D-7 9-D-8 (60395) 9-D-8 9-D-l 7 9-D-l 7 9-D-l 8 (21292) 9-D-l 8 (70695)M 9-D-l 9 (30393) 9-D-19 (70695)M 9-D-20 9-D-20 (70695)M 9-D-33 9-D-33 (70695) 9 - D - 3 4 9-D-34 (70695) 7 (70695)M (70695)M Old Version New 9-D-35 9-D-36 (30393) Version 9-D-35 (70695) I 9-D-36 (70695) 9-D-37 (60395) 9-D-37 (70695)M 9-D-38 9-D-38 (70695) 9-D-39 9-D-39 (70695) 9-D-40 9-D-40 (70695) 9-D-41 9-D-4 1 (70695) 9-D-42 9-D-42 f706951 9-D-43 9-D-43 (70695) 9-D-44 9-D-44 (70695) 9-D-45 9-D-45 (70695) 9-D-46 9-D-46 (70695) 9-D-47 9-D-47 (70695) 9-D-48 (E) 9-D-48.(70695)(E) 9-D-49 9-D-49 (70695) 9-D-50 9-D-50 006951. 9-D-51 9-D-51 (70695) 9-D-52 9-D-52 (70695) 9-D-53 9-D-53 (70695) 9-D-54 9-D-54 (70695) 9-D-55 9-D-55 (70695) 9-D-56 (30393) 9-D-56 (70695) 9-D-57 (30393) 9-D-57 (70695) I Ei 9-D-62 (70695) 9-D-63 (30393) 9-D-63 (70695) 9-D-64 (30393) 9-D-64 8 (70695) . r Old Version New 1 Version 9-D-64-l (70695) 9-D-64-2 (70695) 9-D-64-3 (70695) 9-D-644 (70695) Insert these sheets after page 9-D-64. 9-D-71 9-D-71 (30393) 9-E-l (30393) 9-E-l (70695) 9-E-6 (70695) 9-E-7 (70695)M 9-E-8 (70695) 9-E-8-l (70695) 9-E-9 (21292) blank 9-E-9 (70695) 9-E-l 0 (30393) 9-E-l 0 (70695) 9-E-11 9-E-11 (30393) (70695) 9-E-l l-l (70695) blank 9-E-l 6 9-F-l (70695) 9-F-2 (70695)(F) 9-F-3 (70695) 9-F-4 (50195) 9-F-4 (70695) 9-F-5 9-F-5 9-K-l 0 9-K-l 0 9-L-l 9-K-l 1 (70695) 9-K-l 2 (70695) 9-L-l 9-M-6 9-M-6 (70695) 9-M-7 9-M-7 9-M-8 9-M-8 (70695) blank blank Cover page (Section 10) Cover page (Section 10) 1 O-l (70695)M 10-l (60395) 9 . Old New Version Version 1 O-2(60395) 10-2 (70695)M lo-3(60395) lo-3(70695)M 10-A-l (30393) 10-A-l (70695) 10-B-l (60395) 10-B-l (70695)M 10-B-2 (60395) lo-&2(70695)M 10-C-l 10-C-l 10-c-2 (30393) lo-C-2(70695)M 10-C-3 (60395) lo-C-3(70695)M 10-c-4 (30393) 10-C-4(70695) 10-c-5 lo-C-5 10-C-6 (60395) lo-C-6(70695)M 10-C-7 (60395) lO-G7(70695)M 10-C-14(21292) lo-C-14(70695)M 10-c-15 lo-C-15 10-C-22(30393) 10-C-22(30393) 10-C-23(30393) 10-C-23(70695) 10-C-23-1 (70695) . blank 10-C-24(70695) 10-C-24 10-c-25 . 10-C-25 10-c-28(50195) 10-C-28(70695) 10-C-29(60395) 10-C-29(60395) 10-c-30(50195) 1 o-c-30 (70895)(F) 10-C-31(30393) 10-C-31 (70695) 10-C-31-1 (70695) blank 10-C-34(50195) 10-C-34(70695) 10-C-35(50195) 10-C-35(70695) 10-C-76 10-C-76 10-C-77(60395) 10-C-77(70695) 10-C-78(60395) lO-G78(70895)M 10-C-79(60395) lOG79(70695)M 10-C-80(60395) lO-G80(70695)M 10-C-81 (50195) 10-C-81 (70695) 10 New Version Old Version IO-C-82 (30393) 10-C-82(30393) 10-C-82-1 (50195)(E) 10-C-82-1(70695)(E)M 10-C-82-2(50195)(E) lo-C-82-2(70695)(E)M 10-C-82-3(50195) lo-C-82-3(70695)(E)M 10-C-82-4(50195)(E) 10-C-82-4(70695)(E)M 10-C-83(21292) 10-C-83 (21292) 10-C-108(60395) 10-C-108(60395) 10-D-1 (21292) lo-C-109(70695)M IO-C-llO(70695)M 10-C-111 (70695)M lo-C-112(70695)M lo-C-113(70695)M 10-C-120(70695) 10-C-121 (70695) 10-C-122(70695) 10-C-123(70695) 10-C-130 (70695) 10-C-131 (70695) 10-C-132(70695) 10-D-1 (212921 10-D-4(21292) 10-D-4(21292) 10-D-5 (30393) 10-D-5(70695) 10-D-5-1 (70695) blank 10-D-6(21292) 10-D-6(21292) 10-D-7(21292) 10-D-7(70695) Coverpage(Section14) I Coverpage(Section14) 14-1 14-1 (706951 14-2 14-2 (70695)M 14-3 14-3 (70695)M 14-E-4 14-E-4(70695)M 14-E-5 14-E-4-1 (70695) blank 14-E-5 11 Old Version New Version 14-E-6 14-E-6 (70695) 14-E-7 14-E-6-1 (70695)M blank 14-E-7 14-E-37-1 (70695)M 14-E-37-2 (70695)M 14-E-37-3 (70695)M 14-E-37-4 (70695)M Insert these sheets after page 14-E-37. 14-G-3 14-G-3 (70695)M 14-G-4 14-G-4 Cover page (Section 15) Cover page (Section 15) 15-l 15-l (70695)M 15-2 15-2 (70695) 15-A-l 15-A-1 15-E-5-1 (70695)M - 15-E-5-2 (70695)M insert this sheet after page 15-E-5. 15-F-2 15-F-2 (70695)M 15-F-3 15-F-3 15-G-3 (70695) blank Insert this sheet after page 15-G-2. 12 Section 1 System Outline (Section 1) System Outline Contents Overview .......................................................................................................... Page 1 -A-l 1.00 The Structure of This Manual ................................................................ 2.00 Some Conventions Used in This Manual ............................................... 3.00 System Description ................................................................................ 4.00 Communication Needs .......................................................................... 5.00 Service Cards Description ..................................................................... 1 -A-l l-A-2 1 -A-3 1 -A-3 1 -A-S System Components ........................................................................................ 1-B-1 1 .OO Components List .................................................................................... 2.00 System Connections .............................................................................. 1-B-1 1 -B-2 C Features ........................................................................................................... l-C-1 D Administration A B 1 .OO 2.00 3.00 4.00 5.00 6.00 E .................................................................................................. Introduction ............................................................................................ System interface .................................................................................... Programming ......................................................................................... Test ........................................................................................................ Monitor ................................................................................................... Backup Utility ......................................................................................... 1-D-l l-D-1 l-D-1 . l-D-2 l-D-2 l - D - 3 l-D-3 System Configuration ....................................................................................... l-E-1 1 .oo 1-E-l l-E-2 l-E-3 l-E-3 l-E-4 1 -E-4 l-E-5 l-E-5 l-E-6 1 -E-6 l-E-6 l-E-6 l-E-7 l-E-7 l-E-8 l-E-8 l-E-9 l-E-9 l-E-10 2.00 3.00 4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00 13.00 14.00 15.00 16.00 17.00 Basic Shelf ............................................................................................. Expansion Shelf ..................................................................................... Attendant Console ................................................................................. CPU Card .............................................................................................. TSW Card .............................................................................................. Power Unit ............................................................................................. LCOT Card ............................................................................................ GCOT Card ............................................................................................ PLC Card ............................................................................................... SLC Card ............................................................................................... 10.01 SLC Card.. ................................................................................... 10.02 SLC-M Card ................................................................................. HLC Card ............................................................................................... ATLC Card ............................................................................................. DISA Card .............................................................................................. DID Card ................................................................................................ OPX Card .............................................................................................. DPH Card .............................................................................................. AGC Card .............................................................................................. (70:&M . Page I-E-IO .................................... 18.00 RMT Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . l-E-11 19.00 T-SW Conference Expansion Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-E-II ..................................... 20.00 OHCA Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 .OO T-SW OHCA Expansion Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..*.*.....*............ l-E-11 l-E-11 22.00 OPX Power Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..-.... l-E-12 23.00 T-l Digital Trunk Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A. Overview 1 .OO The Structure of This Manual Section 9 System Programming (VT220 and Compatibles) This section provides information for the programming of the system database using VT220 and Compatibles. Introduction This system reference manual provides general technical information on Panasonic KX-1336 system. This includes a description of the system, its hardware and software, features and service, environmental requirements. This manual is intended to serve as an overall technical reference for the system. Section IO System Programming (Dumb) This section provides information for the programming of the system database using Dumb terminal. Organization This manual is comprised of the following 19 sections. Section 11 System Programming (PITS) This section provides information for a certain programming of the system database using PITS telephone. Section 1 System Outline This section describes the overall information of the system and the construction of this Service Reference Manual. Section 12 Station Programming (PITS) This section provides information for the programming of various features specific to each PITS telephone and DSS console using PITS telephone. Section 2 Installation This section describes how to install and start up the system. Section 13 Station Programming (AlT) This section provides information for the programming and the back-up of the attendant console database using the attendant console. Section 3 System Features and Operation This section describes the basic system features: Section 4 Station Features and Operation (PITS) This section describes the basic features and operations from the viewpointof Proprietary Integrated Telephone System (PITS) users. The basic features and required operations for DSS console are also described. - Section 14 Maintenance (VT220 and Compatibles) This section describes the information necessary for monitoring, testing, and maintaining the system using Vr220 and Compatibles. Section 15 Maintenance (Dumb) This section describes the information necessary for monitoring, testing, and maintaining the system using Dumb terminal. Section 5 Station Feature and Operation (SLT) This section describes the basic features and operations from the viewpoint of Single Line Telephone (SLT) users. Section 16 Backup Utility-On-Site This section provides the information for saving and loading of the system programming data (including attendant console database) at on-site. Section 6 Station Feature and Operation (ATT) This section describes the basic features and operations from the viewpoint of the Attendant Console (ATT) Operator. Section 17 Backup Utility-Remote Location This section provides the information for saving and loading the system programing data (including attendant console database) from a remote location. Section 7 Preparation for Programming and Operation (VT220 and Compatibles) This section describes the basic usage and available functions of VT220 and Compatibles. Section 18 Abbreviations This section provides a list of abbreviations used in this manual. Section 6 Preparation for Programming and Operation (Dumb) This section describes the basic usage and command reference of Dumb terminal. Section 19 Index l-A-1 Holding Features Conversation Features Hold allows an extension user to suspend a call. This feature allows users to temporarily disconnect from one conversation and either make or answer another call. Music on-hold or message may be provided to the held party if available. Conference allows up to 3 parties (maximum two outside parties), including the originator, to join a call. Paging Features Paainq allows extension users to make announcement through built-in speaker of Proprietary Integrated Telephone (PITS) and/or external Pager Equipments. Call Park allows a user to place a call on hold, then pick up the call at any station in the system. The user can page another party to pick up the parked call or may move to another location and then m-access the call. Other Features Station Messaae Detail Recordina (SMDR) generates detailed call information on all CO calls and sends this information to the printer. SMDR also generates detailed data on Error Log Records, System Programming Data and Traffic Information. Transferring Features Transfer allows a user to transfer any call to another party This feature supports transfer of calls from the called party to another party for completion of a transaction. Off Premise Extension (OPX) allows Single Line Telephones (SLT) installed off the premises can be operated via a public or private network in exactly the same way as extension on the premise. Call Forwarding allows users who are away from their phones to receive calls at another phone. This feature supports roving personnel and shared office space or company staff. Account Code Entry allows a user to associate calls with an account code for charge-back purposes. No. 1 2 3 4 5 6 7 a 9 10 11 12 13 14 15 16 17 la Item Tenant Operator Speed Dialing-System. Speed Dialing-Station/SLT One Touch Dialing-Station/PITS Call Park Area Programmable Absent Message Trunk Group Equal Access Group OCC Access Group Toll Restriction Level Paging Group ICM Group Pickup Group UC0 Group Class of Service Primary ON (PDN) Message Waiting Maximum number 2 2 200 10 23 20 10 16 4 4 16 a a 32 32 32 3 500 1 -A-4 per system/ station system tenant system station station system system system system system system system system system system system station system 5.00 Service Cards Description Extension cards CO trunk cards Prorxietaw lntearated Line Circuit (PLC) Card; This card interfaces 8 PITS telephones/DSS Looo Start Central Office Trunk (LCOT) Card: * This card interfaces 8 central office loop start trunks and the TDM bus. It is available to connect 8 CO lines to the system per LCOT card. With loop start, you seize a line by bridging through a resistance the tip and ring (both wires) of your telephone line. consoles and the TDM bus. It is available to connect 8 PITS telephones, DSS consoles to the system per PLC card. Sinale Line Telephone Line Circuit (SLC) Card; This card interfaces 8 SLT type telephones and the TDM bus. It is available to connect 8 SLT telephones to the system per SLC card. Ground Start Central Office Trunk IGCOT) Card; * This card interfaces 8 central office trunks and the TDM bus. It is available to connect 8 CO lines to the system per GCOT card. A way of signaling on subscriber trunks in which one side of the two wire trunk (typically the “Ring” conductor of the Tip and Ring) is momentarily grounded to get dial tone. SLC Card with Messaae Waitina (SLC-MI; This card is the same as the standard SLC card except that it has the capability to turn on and off the message waiting lamp of a Single Line Telephone. Hvbrid Line Circuit (HLC) Card; This card interfaces PITS/SLT type telephones, DSS consoles and the TDM bus. It is available to connect 8 PITS/SLT telephones/ DSS consoles to the system per HLC card. _ Off Premise Extension Trunk (OPX) Card; This card interfaces 4 off premise extensions through off premise extension power unit. Attendant Console Line Circuit IATLC1 Card; This card interfaces 2 Attendant Consoles and the TDM bus. It is available to connect 2 attendant consoles to the system if this card is installed. l There are two types of switched trunks one can typically lease from a local phone company- _ Loop Start and Ground Start. You must be careful to order the correct type of trunk from your local phone company and correctly install your telephone system at your end - so that they both match. Direct Inward Dialina Trunk (DID) Card; This card interfaces 4 central office trunks arranged for Direct Inward Dialing (DID) and the TDM bus. T-l Diaital Trunk Card: This card interfaces 1 T-l line and TDM bus. It is available to connect a T-l line to the system per T-l digital trunk card. A T-l line has capacity of 24 voice conversations. 1 -A-5 (70695)M Resource cards Other cards Direct inward Svstem Access (DISAI Card; This card interfaces 4 central office trunks arranged for Direct Inward System Access (DISA) and the TDM bus. Doorohone Circuit (DPH) Card; This card interfaces 4 doorphones and the TDM bus. Up to 4 doorphones can be connected to the system. Automatic Gain Control lAGC\ Card; This card is used to maintain volume of CO-CO communication. An electronic circuit which compares the level of an incoming signal with a previously defined staqdard and automatically amplifies or attenuates that signal so it arrives at its destination at the correct level. Time Switch Conference ExDansion Card (T-SW Conference1 Card; This card provides 64 additional conference trunks, and is installed on the T-SW card. Off Hook Call Announcement (OHCAl Card: This card is for Off Hook Call Announcement features, and is installed on the HLC card or PLC card. Remote Circuit fRMT1 Card; This card is necessary for accessing the system from a remote location. Time Switch Off Hook Call Announcement ExDansion (T-.SW OHCAI Card: This card is for Off Hook Call Announcement features, and is installed in the Basic Slot 2. System Configuration N o . I _ 2 R Item I , ,,C+PLC+SLC+OPX+DID+LCOT/GCOT+T-1 DID+LCOT/GCOT+T-1 . npu IlT. l l -.- l”“, -a I DOftS) I I . shelf 116con Source I I 1; I System = fully expanded system = basic shelf + expansion shelf 1 + expansion shelf 2 * T-l is counted as 3 cards. 1 -A-6 (70695)M 1 system* system* svstem’ system’ system’ svstem* 42 cards (336 Rorts)” 18 cards (144 sorts)” 1 card (4 doorohonPc\ resaurcsg) (4cards(16 .----.JQ 14 cards (16 resource We ‘S) 11 card (1 res -source) , IL -.. ULhrl-“I A le 1 13 1 External Musi;d Maximum number / s y s t e m / - -, ----.- system’ I B. System Components 1 .OO Components List Model No. KX-T336100 KX-1336101 KX-T336102 KX-T336200 KX-T96300 KX-T96145 KX-T96136 KX-T96141 KX-T96161 KX-T96170 KX-T96172 KX-T96174 KX-T96175 KX-T96180 KX-T96181 KX-T96 182 KX-T96185 KX-T96186 KX-T96187 KX-T96191 KX-T96193 KX-T96196 KX-T336 104 KXiT336105 Name Basic Shelf CPU card T-SW card Expansion Shelf Attendant Console Attendant Console Keyboard Off Hook Call Announcement (OHCA) Card Attendant Console Line Circuit (ATLC) Card Doorphone Circuit (DPH) Card Hybrid Line Circuit (HLC) Card Proprietary ITS Line Circuit (PLC) Card Single Line Telephone Line Circuit (SLC) Card Single Line Telephone Circuit (SLC) Card with Message Waiting Loop Start Central Office Trunk (LCOT) card Ground Start Central Office Trunk (GCOT) Card Direct Inward Dialing Trunk (DID) Card Off Premise Extension Trunk (OPX) Card Off Premise Extension (OPX) Power Unit T-l Digital Trunk Card Direct Inward System Access (DISA) Card Automatic Gain Control(AGC) Card Remote Circuit (RMT) Card Time Switch Conference (T-SW Conference) Expansion Card Time Switch Off Hook Call Announcement (T-SW OHCA) Card 1 -B-l (70695)M - Model No. KX-T30820 KX-T30830 KX-T30850 KX-T61620 KX-T61630 KX-T61650 KX-T123220 KX-T123230 KX-T123230D KX-T123235 KX-T123250 KX-T7020 KX-T7030 KX-T7050 KX-T7052 KX-T7130 KX-T61640 KX-T123240 KX-T7040 KX-T30865 KX-A26D . Name Proprietary Telephone (3 Co’s) Proprietary Telephone with LCD (3 CO’s, 8 DSS’s) Proprietary Telephone (3 CC’s) Proprietary Telephone (6 Co’s) Proprietary Telephone with LCD (6 CO’s) Proprietary Telephone (6 Co’s) Proprietary Telephone (12 CO’s) Proprietary Telephone with LCD (12 CO’S) Proprietary Telephone with LCD (12 CO’s) Proprietary Telephone with LCD (12 Co’s) Proprietary Telephone (12 CO’s) Proprietary Telephone (12 CC’s) Proprietary Telephone with LCD (12 Co’s) Proprietary Telephone (12 CO’s) Single Line Telephone with FLASH button Proprietary Telephone with LCD (12 CO’s) DSS Console (16 DSS’s, 16 PF buttons) DSS Console (32 DSs’s, 16 PF buttons) DSS Console (32 DSS’s, 16 PF buttons) Doorphone Battery Adapter . 1-B-l-l (70695)M . 5.00 Monitor 6.00 Backup Utility Monitor function provides displaying current status of “Error Log,” “Device Status” and “Traffic information” individually on the screen. Making backups of the system programming data and keeping it is extremely important in the unlikely event that system programming data are lost in a system failure. Backup Utility consists of %ave” and “load.” Save is to transmit a file of data from your system to backup device. Load is to send a file of data on your system from backup device. Before beginning saving or loading, check carefully that you are going to the direction you want. It’s very easy to erase files if you make a mistake and confuse saving and loading. Starting up the backup operation can be done both at on-site and from a remote location. Refer to Section 16 ‘Backup-Utility on-site” and Section 17 ‘Backup Utility-Remote Location” for further information. Error Log When a system maintenance object begins to fail periodic testing, the system automatically generates an error record which is stored in the Error Log. Consulting the error log should be the first step in diagnosing system related troubles. For further information, refer to Section 14-D2.02 ‘Consulting the Error Log.” Device Status Provides information about current operation status of the following items individually on the screen. l l l l System Card Port Conference Trunk Traffic Provides current traffic information about following items individually. l l l l l l l Station Trunk Group Attendant Console DISA OGMl OGM2 AGC Refer to Section 14-G ‘MonitoP for further information about monitor. l-D-3 E. System Configuration 1 .OO Basic Shelf Basic Shelf is always required. Basic Shelf contains its own power supply and 15 mounting spaces called “Slot.” CPU card and T-SW card are installed at factory. Basic Slot 2 is provided for installing the optional T-SW OHCA card. The remaining 12 slots provide mounting space for the various cards that can be used. Any optional service card can be mounted in any of these 12 slots. So these slots are called “Free Slot.” Basic Shelf consists of the followings. No. Name 1 2 3 POWER-for Power Unit BSl (Basic Slot 1) - for CPU card BS2 (Basic Slot 2) - for optional T-SW OHCA card BS3 (Basic Slot 3) - for T-SW card FSl to 12 (Free Slot 1 to 12) - for optional service card 4 5 Number 1 1 1 1 12 Construction of Basic Shelf - - F F S S 6 7 G Free Slot can be equipped with the following optional service cards. a. Loop start central office trunk (LCOT) Card b. Ground start central office trunk (GCOT) Card c. Hybrid line circuit (HLC) Card d. Proprietary ITS Line circuit (PLC) Card e. Single line telephone line circuit (SLC) Card f. Single line telephone line circuit with Message Waiting (SLC-M) Card g. Direct inward dialing trunk (DID) Card h. Off premise extension trunk (OPX) Card i. Doorphone circuit (DPH) Card j. Automatic Gain control (AGC) Card k. Direct inward system access (DISA) Card I. Remote circuit (RMT) Card m. Attendant console Line circuit (ATLC) Card n. T-l Digital Trunk Card 1-E-l (70695)M 1 B S 3 2.00 Expansion Shelf Expansion Shelf consists of the following. Exoansion Shelf is provided optionally. Up to two Expansion Shelves (1 and 2) can be installed on the Basic Shelf to enlarge the ability of the system. Each Expansion Shelf contains its own power supply and 15 mounting spaces for any optional card required for system expansion. Expansion Shelf is installed on top of the basic shelf. I No. 1 2 Name POWER-for Power Unit FSl to 15 (Free Slot) - for optional service card Construction of Expansion Shelf (1 and 2). - - t F F S S 1 2 ii W E R - Free Slot can be equipped with the following optional service cards. a . Loop start central office trunk (LCOT) Card b. Ground start central office trunk (GCOT) Card c. Hybrid line circuit (HLC) Card d. Proprietary ITS Line circuit (PLC) Card e. Single line telephone line circuit (SLC) Card f. Single line telephone line circuit with Message Waiting (SLC-M) Card g. Direct inward dialing trunk (DID) Card h. Off premise extension trunk (OPX) Card i. Doorphone circuit (DPH) Card j. Automatic Gain control (AGC) Card k. Direct inward system access (DISA) Card I. Remote circuit (RMT) Card m. Attendant console Line circuit (ATLC) Card n. T-l Digital Trunk Card 1 -E-2 (70695)M Number i .15 3.00 Attendant Console 4.00 CPU Card Functions Functions Up to two Attendant Consoles (optional-with CRT display) can be equipped with the system.. (1) Call process and basic shelf main protocol. (Microprocessor 8OC286). Time switch (TSW) control, detection of system clock alarm, basic shelf power down and expansion shelf power down alarm, watch dog. The attendant console allows one or two attendants to answer, screen, and control incoming calls using Switched Loop Operation. With attendant operation, incoming calls can be screened and forwarded to the proper party for resolution, messages taken for absent users, or forwarded to alternate locations. (2) System switch interface. There are Operation Switch (MODE) (10 modes, 0 to 9) and System Administration Device Selection Switch (SYSTEM) (10 modes, 0 to 9) on the CPU rotary switch. When the system lost the programming data because of system resetting, set system operation mode using these switches when starting up the system again. The attendant console is not dedicated to call processing and feature accessing, and can be used for system data programming and diagnostics. Refer to Section 6 “Station Features and Operation-Attendant Console” for further information about attendant console call processing features, and Section 13 ‘Station Programming-Attendant Console” for further information about attendant console local programming mode. (3) Terminal interface. CPU card has two RS-232C terminal interfaces. Operation (1) Operation Switch (MODE) and System Administration Device Selection Switch (SYSTEM) are set by turning with screw driver. Operation Attendant console is operable for the following. l l l l Call Processing mode System programming Diagnostics Editing local data (2) Reset switch is non-lock push switch. (3) LED for battery alarm lights when voltage of Lithium-battery becomes too low (less than 2SV). (4) LED for watch dog lights when CPU’s software is running away. (5) Watch dog is detecting CPU’s running away. 1 -E-3 l 5.00 TSW Card 6.00 Power Unit Functions Functions (1) Time switch. Capability of switching voice is 512ch x 512ch. (1) Power supply (+5, =15, GND) for a shelf. (2) External battery interface. (+24) Battery power (+24) is input from a battery interface unit in basic shelf with a 2 wire cable. (2) Generation of system clocks. System clocks are 2,048MHz (PCM clock), 8kHz (PCM frame clock). (3) Generation of call progress tone. Call progress tones are 350+440Hz, 480+620Ht and 440+480Hz. (3) Power failure detection. A circuit in POW detects power failures of +S/DC, +15VDC, AC power supply, and 2 power alarm signals are sent to CPU card as DC alarm and AC alarm. 620Hz. (4) Conference circuit. T-SW card has 3 party x 8 conference’s circuits. For CO-CO speech amp., AGC card can be inserted to a free slot of basic or expansion shelf. (4) Generation of bell signal. (20Hz, 1 OOVOp) @)-Paging interface. T-SW card has 2 pm-amp. circuits for paging. In order to adjust volume, each amp circuit is equipped with a knob. (6) Music-in interface. T-SW card has 2 interface circuits for music on hold or BGM. Operation (1) A knob for adjusting volume of external paging is turned with a screw driver from front of T-SW card. (2) LED indicator or the T-SW card lights when system reset or T-SW local reset occurs. l-E-4 03 7.00 LCOT Card 8.00 GCOT Card Functions Functions LCOT GCOT (KX-T96180) ---Loop Start Central Office Trunk card (8 CO Lines/ card) (1) Loop start CO interface. CPC detection, 1 DTMF driver. With loop start, you seize a line by bridging through a resistance the tip and ring (both wires) of your telephone line. (1) Ground start CO interface. CPC detection, 1 DTMF driver. A way of signaling on subscriber trunks in which one side of the two wire trunk (typically the “Ring” conductor of the Tip and Ring) is momentarily grounded to get dial tone. (2) Power failure transfer (PFT) by each port. Tip/Ring of CO are connected to a CO interface circuit, and directly to LCOT PFT modular, When power failure occurs, CO Tip/Ring leads are directly connected to SLT Tip/Ring leads, but LCOT PFT modular and SLT PFT modular should be connected each other with connection cord in advance. (3) Diagnostic transfer (DT) by each port. A diagnostic relay is placed in Tip/Ring of each port. During diagnostic test, only one diagnostic relay in an LCOT of a system is activated. (KX-T96181) ----Ground Start Central Office Trunk card (8 CO Lines/ card) (2) Power failure transfer (PFT) by each port. Tip/Ring of CO are connected to a CO interface circuit, and directly to GCOT PFT modular. When power failure occurs, CO Tip/Ring leads are directly connected to SLT Tip/Ring leads, but GCOT PFT modular and SLT PFT modular should be connected each other with connection cords in advance. _ (3) Diagnostic transfer (DT) by each port. A diagnostic relay is placed in Tip/Ring of each port. During diagnostic test, only one diagnostic relay in a GCOT of a system is activated. Operation LED indicator on the LCOT card lights when the system reset or LCOT local reset occurs. Operation LED indicator on the GCOT card lights when the system reset or GCOT local reset occurs. 1 -E-5 (70695)M 9.00 PLC Card 10.00 SLC Cards Functions 10.01 SLC Card PLC card (KX-T96172) Functions (1) PITS and DSS console interface. (8 circuits/ card) Maximum loop resistance : 40 ohms Power supply 1 : +3OV (supplied through speech path, and with current limitation circuit). Power supply 2 : +15V (supplied through data line). SLC card (KX-T96174) (1) Standard SLT interface. Maximum loop resistance : 600 ohms. (including SLT) Power supply : +3OV (with current limitation circuit.) 2 DTMF receivers, dial pulse detector. (2) PITS (KX-T1232300, KX-T123235, KXT7130) interface with OHCA feature. When a PITS with OHCA feature is connected to a port, an OHCA piggy back card (KXT96136) should be mounted to its interface circuit (2) Power Failure Transfer (PFT) by ports 1 through 8. When power failure occurs, SLT Tip / Ring are led by a PFT relay, but SLT PFT modular and LCOT / GCOT modular should be connected each other by connection cords in advance. Operation (3) Diagnostic transfer (DT) by each port. Diagnostic relay is placed in Tip / Ring of each port. During diagnostic test, only one diagnostic relay in the SLT of a system is activated. LED indicator on the PLC card lights when the system reset or PLC local reset occurs. Operation LED indicator on the SLC card lights when system reset or SLC local reset occurs. 10.02 SLC-M Card Functions SLC-M Card (KX-T96175) (1) (2) 1 Same as 10.01 SLC Card (3) (4) SLT with Message Waiting Lamp interface Power supply to Message Waiting Lamp: +80VDC (when 1 mA) Operation Same as 10.01 SLC Card 1 -E-6 (70695)(E)M 11 .OO HLC Card 12.00 ATLC Card Functions Functions HLC card (KX-T96170) is for PITS, DSS console and SLT. (8 extensions / card) (l)ATLC card. (KX-T96141) Attendant console interface. (2 circuits (Attendant console : KX-T96300) (1) Standard SLT interface. SLT interface is quite same as that of SLT card. Operation (2) PITS and DSS console interface. PITS and DSS console interface is quite same as that of PLC card. / card) LED indicator on the ATLC card lights when the system reset or attendant console local reset occurs. (3) Interface for PITS (KX-T123230D, KXT123235, KX-T7130) with OHCA feature. Interface for PITS (KX-T123230D, KXT123235, KX-T7130) with OHCA feature is quite same as that of PLC. (4) Power failure transfer by each port. (when using SLT) Power failure transfer is quite same as that of SLC card. (5) Diagnostic transfer by each port. Diagnostic transfer is quite same as that of SLC card. Operation LED indicator on the HLC card lights when the system reset or HLC local reset occurs. 1 -E-7 (70695)M 13.00 DISA Card 14.00 DID Card Functions Functions DISA (Direct Inward System Access) card. (KX-T96191) DID (Direct Inward Dialing) card (KX-T96182) (1) 4 OGM trunks. OGM duration : 30 seconds, OGM Battery Backup : 5 days. The number of OGM : 1, Recording Algorithm : ADPCM. Wink start/immediate start DID interface. (4 circuits/card) 45V used in circuits is originated from DC-DC converter in DID card. DID card will receive pulse signal only. Operation (2) 4 CO-CO speech paths without amp. A CO-CO speech path consists of up-path and down-path. Up-path is from call-originate CO to callanswer CO, and 1 DTMF receiver and one speech end detector is connected to ft. Down-path is from call-answer CO to calloriginate CO and one speech end detector is connected to it. (3) Speech end detector. Speech end detector detects tones. LED indicator on the DID card lights when the system reset or DID local reset occurs. call progress Operation LED indicator on the DISA card lights when the system reset or DISA local reset occurs. 1 -E-8 (70695)M 15.00 OPX Card 16.00 DPH Card Functions Functions OPX (KX-T96185) ---Off Premise Extension. (4 OPX Lines / card) OPX Power Unit is necessary. Doorphone card (KX-T96161) OPX Power Unit should be connected with OPX card, and Single Line Telephones for OPX should be connected with OPX card. (1) Doorphone interface (4 circuits / card) 4 doorphones can be connected using a modular connector. Doorphone chime is sent to both extension and doorphone at a time when a doorphone button is pressed. (2) Door opener interface (4 circuits / card) DPH card has 4 relays for door opener. (12OVAC. 1A) The relay opens for doorlock, closes for door release. It also opens in the case of power failure. Operation Terminal plate on the DPH card has 8 terminals, 2 leads from door opener are directly connected to two of 8 terminals. Operation interval of door opener is 3 seconds. 1 -E-9 (70695)M 17.00 AGC Card 18.00 RMT Card Functions Functions AGC (Automatic Gain Control) card (KX-T96193) RMT (Remote Circuit) card (KX-T96196) Modem (300/1200 Modem protocol (1) 4 CO-CO speech paths with AGC Amp. and Echo-Suppressor. A CO-CO speech path consists of up-path and down-path, up-path is from call-originate CO to call-answer CO, and AGC amp is inserted and speech end detector is connected. Maximum amplitude rate of AGC is 14 dB. Echo-Suppressor is inserted in a CO-CO speech path. bps) for remote administration. (1) free wheeling (TTY).. Operation LED indicator on the RMT card lights when the system reset or RMT local reset occurs. (2) 4 DTMF transceivers. DTMF transceiver is used as DTMF repeater. So, AGC card microprocessor controls DTMF repeater. (3) 8 Speech End Detectors. Speech end detector of AGC is quite same as that of DISA card. Operation LED indicator on the AGC card lights when the system reset or AGC local reset occurs. l-E-10 (70895)( E)M 19.00 T-SW Conference Expansion Card 21 .OO T-SW OHCA Expansion Card Functions Functions T-SW Conference Expansion card (KX-T336104) T-SW OHCA Expansion card $X-T3361 05) Mounted on T-SW card. 3 party x 64 conference circuits. This card is mounted on Basic Slot 2 for OHCA feature. OHCA card (KX-T96136) for extension port must be installed on the HLC card or PLC card in advance. 20.00 OHCA Card 22.00 OPX Power Unit Functions Functions OHCA (Off Hook Call Announcement) card (KX-196136) This card is mounted on HLC card or PLC card (KX-T96172). OPX (Off Premise Extension) Power Unit (KX-T96186). (KX-T96170) Output is Ringing Signal (1 OOVAC, 20Hz) and 48V DC for OPX Card. This card includes 2 OHCA circuits. Allows an extension user to intrude through the speaker into another extension that is in. conversation using the handset. This feature is available only against the following PITS telephones: KX-T123230D, KX-T123235, KX-T7130. l-E-1 1 (70695)(E)M -.. -- _ 23.00 T-l Digital Trunk Card Functions T-l interface.(l circuit / card) T-l is a digital transmission link with a capacity of 1.544 Mbps. A T-l card carries 24 voice conversations. Frame Format : D4 / ESF Line Coding : AMI / B8ZS Channel Type : LCO / GCO / DID / OPX / TIE Signaling : DP / DTMF (DTMF:24 receivers and 6 generators) Operation RED LED indicator on T-l card lights when the system reset or T-l card local reset, T-l line fault occurs. 1-E-12 (70695)M 3.10 G C O T Card (KX-T96181). ........................................................... 3.11 DID Card (KX-T96182) ................................................................ 3.12 OPX Card (KX-T96185). .............................................................. 3.13 DISA Card (KX-T96191) .............................................................. 3.14 AGC Card (KX-T96193) .............................................................. 3.15 RMT Card (KX-T96196) .............................................................. 3.16 T-l Digital Trunk Card (KX-T96187) ............................................ 4.00 Parallel Connection of the Extensions ................................................. 5.00 Auxiliary Connection for Power Failure Transfer ................................... 6.00 Connection of the Battery Adaptor (KXA26D) ...................................... D E Connection of Optional Peripheral Equipments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-D-l 1 .OO Paging Equipment ................................................................................. 2.00 External Music Source.. ......................................................................... 3.00 RS-232C Interface ................................................................................. . ............. 3.01 Connection to the Printer.. ............................................. 3.02 Connection to the Data Terminal ................................................. 2-D-l 2-D-2 2-D-3 2-D-5 2-D-6 Installation of Attendant Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-E-i 1.00 2.00 3.00 4.00 5.00 6.00 7.00 8.00 F ............... Page 2-c-22 2-c-25 2-C-26 2-C-28 2-C-28 2-C-28 2-C-28-l 2-c-29 2-C-30 2-C-32 Configuration ......................................................................................... Attendant Console Assembly ................................................................. Handset Connection .............................................................................. Installation a n d Removal of CRT Unit.. .................................................. 4.01 CRT Unit Installation .................................................................... 4.02 CRT Unit Removal ....................................................................... Keyboard Connection ............................................................................ Connection with KX-T336 System ........................................................ A C Power Cord Connection.. ................................................................. Various Adjustments .............................................................................. Starting Up the KX-T336 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............. 2-E-l 2-E-3 2-E-4 2-E-5 2-E-5 2-E-7 2-E-8 2-E-9 2-E-l 0 2-E-l 1 2-F-l 2-F-l 1 .OO System Power-Up Procedure ................................................................ .2-F-2 2.00 CPU Rotary-Switch Features ................................................................. 2-F-2 2.01 Operation Switch (MODE). .......................................................... 2.02 System Administration Device Selection Switch (SYSTEM). ...... 2-F-5 2-F-6 2.03 Operation Sequence for System Starting Up .............................. . A. Preparation 1 .OO Introduction This section describes the procedures required to install the KX-T336 System. Detailed instructions for planning the installation site, installing the shelves and optional cards, and cabling of peripheral equipments are provided. Further information on system expansion and peripheral equipment installation is included. 2-A-l 3.16 T-1 Digital Trunk Card (KX-T96187) l Insert the card into Free Slot 1, 5 or 7-l” mark Connecting the Central Office Line Insert the RJ-48C plug of the telephone line cord (4-conductor wiring) into the RJ-48C jack (T-l port on the KX-T96187). RI Tl R T I View of TEL Jack (CO) To Chantiel Service Unit (CSU) or Other KX-T96187 0 l ‘1 // Use 4-conductor wiring cord. T-l Port T-l DIGITAL TRUNK CARD (KX-T96187) Transmit Equalizer Setting p t+i-&h-i (defaulf) Note: The User cannot change this setting. 2-C-28-l (70695)M Maximum Cabling Distance of the T-l Line + 22 AWG : Under 1 Om 24 AWG : Under 10m 4 - ’ Modular Jack from the Central Office (CO) csu 1 22 AWG : Under 10m 24 AWG : Under 10m 5 Other KX-T96187 Note : The T-l line cable must be 22 AWG shielded twisted pair cable or 24 AWG UTP (unshielded twisted pair) cable supported Category 5. Cable Pin Numbers to be connected for KX-T96187 KX-T96187 c-) Channel Service Unit (CSU) 8 Pin Modular jack on KX-T96187 KX-T96187 cs KX-T96187 Receive lead pair 8 Pin Modular Jack on m-T961 87 Receive > lead pair 8 Pin Modular jack on KX-T96187 Rl 1 ’ ( T12 3 Transmit R 4 lead pair ( T 5 6 7 8 _ Transmit > lead pair 2-C-28-2 (70695)M 6 7 8 - --- System Clock Mode for KX-T96187 KX-T336 system I I Clock Mode = External KX-T336 system lWT96187 Clock Mode = External KX-T336 system KX-T96187 Clock Mode = Internal Note: System Clock mode is programmed by CLK command.(see 10-C-64.02) 2-c-28-3 (70695)M Short Jumper Setting for KX-T96187 SW2 SW3 SW5 sw2, SW3 /I : z. ;:4.A;;X-T336 ( d e f a u l c Note: Loop Back Test The user can check KX-T96187 by the following procedure. ’ . 1. Remove T-l cable from KX-196187. 2. Set SW2 and SW3 to TEST position. 3. Check SYNC LED (green). If SYNC LED does not light or flash, KX-T96187 does not work. 4. Set SW2 and SW3 to NOR position. l KX-T96187 Cable must be removed. 2-C-28-4 (70695)M t ) - LED indication for KX-T96187 - FALT -SYNC ERROR -RAI -AIS -SYNC Item FAULT SYNC ERdOR RAI Status ON OFF ON OFF ON AIS ~-OFF ON SYNC Contents Card Fault Normal Clock Synchronization Error or Loss of Signal Normal Receive Remote Alarm Indication signal (Yellow Alarm) Normal Send Alarm Indication Signal (Yellow Alarm) OFF Normal FLASH Clock Master at External Clock Mode ON Detection of Signal 1-OFF ~-NO bet&on of Signal 2-C-28-5 (70695)M --- 2.00 Automatic Route Selection (ARS) ......................................................... 3.00 Tone/Pulse Conversion ........................................................................ 4.00 Automatic Pause Insertion ................................................................... D Receiving Features.. ........................................................................................ 1 .OO Attendant Console (ATT) Operation ...................................................... 1 .Ol Load Sharing ............................................................................... 1.02 Simultaneous Ringing.. ................................................................ 1.03 Interconsole IRNA ....................................................................... 2.00 Attendant Console-less Operation ........................................................ 2.01 Direct In Line (DIL) ...................................................................... 2.02 Direct Inward System Access (DISA) .......................................... 2.03 Direct Inward Dialing (DID). ......................................................... 2.04 Trunk Answer From Any Station (TAFAS)-Day Service.. ............. 2.05 Uniform Call Distribution (UCD)-General..................................... 2.06 Uniform Call Distrfbutlon (UCD)-with/without OGM.. ................... 2.07 Private CO (PCO) ........................................................................ 2.08 Single C O (SCO) ......................................................................... 2.09 Group CO (GCO) ......................................................................... 2.10 Flexible SCO/GCO Assignment .................................................. 2.11 Multiple GCO Assignment ........................................................... 3.00 Flexible Ringing Assignment ................................................................ 3.01 Flexible Ringing Assignment-No Ringing .................................... 3.02 Flexible Ringing Assignment-Delayed Ringing ........................... 4.00 Discriminating Ringing ........................................................................... 5.00 Station Hunting ..................................................................................... 5.01 Station Hunting-Circular .............................................................. 5.02 Station Hunting-Terminal ............................................................. P a g e 3-c-21 3-C-36 3-c-37 3-D-l 3-D-l 3-D-2-l 3-D-2-2 3-D-2-3 3-D-3 3-D-3 3-D-4 3-D-7 3-D-8 3-D-9 3-D-11 . 3-D-15 3-D-16 3-D-17 3-D-17-1 3-D-l 7-3 3-D-l 8 3-D-18 3-i-i: * 3-D-20 3-D-20 3-D-21 E Holding Features .............................................................................................. 1 .OO Music on Hold ........................................................................................ 2.00 Held Call Reminder ................................................................................ 3.00 Transfer Recall ..................................................................................... 3-E-l F Other Features ................................................................................................. 1 .oo Station Message Detail Recording (SMDR) .......................................... 2.00 Off Premise Extension (OPX) ................................................................ 3.00 Walking Station ...................................................................................... 4.00 Outgoing Message (OGM) Recording and Playing Back.. .................... 5.00 Intercept Routing-No Answer (IRNA) ..................................................... 6.00 Rerouting ............................................................................................... 7 . 0 0 Calling Party Control (CPC) Signal Detection ....................................... 8.00 CO Busy Out. ......................................................................................... 9.00 Parallel Connection of Extensions ......................................................... 10.00 Voice Processing System (VPS). ........................................................... 10.01 Voice Mail Integration ................................................................ 3-F-l (70:&M 3-E-l 3-E-2 3-E-3 3-F-l 3-F-3 3-F-3 3-F-5 3-F-8 3-F-9 3-F:: m 3-F-12 . . 10.02 DTMF-Tone Integration ............................................................. Call Accounting Summary ..................................................................... Waiting for Second Dial tone ................................................................. Timed Reminder with OGM (Wake-up Call) .......................................... TIE Lines................................................................................................ 14.01 Calling from TIE to TIE .............................................................. 14.02 Calling from TIE to CO .............................................................. 14.03 Calling from CO to TIE .............................................................. 14.04 Alternate Routing ....................................................................... 15.00 T-l Carrier .............................................................................................. 16.00 Limited Call Duration ............................................................................. 11 .OO 12.00 13.00 14.00 Page 3-F-21 3-F-52 3-F-62 3-F-64 3-F-67 3-F-72 3-F-76 3-F-79 3-F-81 3-F-84 3-F-86 -. ___ In addition to the feature numbers which can be set in ‘System-Numbering Plan,” fixed feature numbers are provided and these are shown in the following table. Fixed Feature Numbers Function Number While busy tone is heard Call-back (for extensions only) Busy Override While Do Not Disturb tone is heard DND Override When handset is on-hook (PITS only) Time display/date display switching Background music on/off Day/Night mode display 6 1 1 * 1 # While talking to doorphone Open the door 5 Others Extension time and data display mode * switching Account code delimiter # Account code delimiter (for dial pulse type 99 SLT‘only) + Account code m-input l The feature numbers which are set in the “System-Numbering Plan” are listed on the following pages. 3-B-2 Flexible Feature Numbers 3-B-3 (70695)M Flexible Feature Numbers Flexible Feature Numbers Funktion 3-B-4-l (70695) 2.00 Directory Number (DN) DescriptionDirectory numbers are the software type logical numbers which are programmed to match the hardware type physical numbers (port numbers) attached to ports of extensions. Accordingly, directory numbers are extension numbers. System-Numbering Plan .------------__--------------------------------Numbering Plan (Ol/ll) r--T--“‘-----‘-‘-“--------5-‘--r--’1--~---~----r----, ; DGll DG2; DG3; DG_4; (No.1 Feature ~--~-----------------------; 1 : 1st Hundred Block Extension ~--.-~---~-----~-1 :--~------------------------~----~---,----~---, f - I - I I 2 12nd Hundred Block Extension f 6 I ---*----p---y ------y----p ;--+-----------------I 3 I3rd Hundred Block Extension f 7 : 0 : - 1 - :~--+---,,-------------------~----~---~----~---~ ! 4 14th Hundred Block Extension i 8 [ 0 / - / - i I f 1 Directory numbers are assigned in “ConfigurationDN Assignment” to be three or four digits. Only numeric characters “0 to 9” can be used as a Directory Number. DNs DNs DNs DNs Directory number setting follows the setting in “System-Numbering Plan”, 1 st Hundred Block Extension through 16th Hundred Block Extension. Programming System Programming “Configuration-ON Assignment” “System-Numbering Plan”, 1st Hundred Block Extension . . Reference VT Dumb 9-c-3.00 10-c-3.00 9-D-6.01 16-C-l 0.66 9-D-6.02 16th Hundred B&ck Extension Conditions There are two types of directory numbers: the Primary Directory Number (PDN) and the Secondary Directory Number (SDN). For further details of PDN, refer to Section 4-B-3.01 “PDN Button.” For SDN, refer to Section 4-B-3.02 ‘SDN Button.” If you assign onfy one digit in “System-Numbering Plan”, 1 st Hundred Block Extension through 16th Hundred Block Extension, you can assign threedigit DNs which start with the preassigned digit in “Configuration-DN Assignment.” if you assign leading two digits in “SystemNumbering Plan,” you can assign four-digit DNs which start with the pre-assigned two digits in “Configuration-DN Assignment.” 3-B-5 (70695) 1 1 from 8000 to 8099 are assignable. ) from 7000 to 7099 are assignable. from 800 to 699 are assignable. from 500 to 599 are assignable. 7.02 Call Pickup Group 7.03 Uniform Call Distribution (UCD) Group Description Description Extensions belonging to a particular intercom group can be divided into call pickup groups which can execute the Dial Call Pickup feature. The call pickup group belonging to an intercom group is set by programming in the “Group-Call Pickup Group”, ICM. It is possible to execute UCD functions in a group composed of one or more Call Pickup Groups. Such a group is called a UCD group. The “Group-Call Pickup Group” screen determines which pickup group(s) will be in the UCD group. Up to 32 UCD groups can be assigned in the system. The UCD group and the call pickup group configuring the UCD group must belong to the same intercom group. See Section 3-D-2.06 “Uniform Call Distribution (UCD)-without OGM” and Section 3-D-2.06 “Uniform Call Distribution (UCD)-with OGM” for further information about the UCD functions. See the previous Section 3-B-7.02 L%all Pickup Group” for details on Call Pickup Groups. See Section 3-B-7.01 ‘Intercom Group” for further information about ICM Groups. Up to 32 call pickup groups can be assigned in the system. Extensions programmed into call pickup groups are set in the “Extension-Station”, Pickup Group. It is not necessary for all extensions to be in a pickup group. See Section 4-D-3.01 “Dial Call Pickup” for further information about the Dial Call Pickup feature. Programming . ~1 Programming Conditions r Different call pickup groups can have the same UCD and/or paging groups. Conditions System Programming ‘Group-Call Pickup Group”, UCD None See Section 3-B-7.04 “Paging Group” for details on Paging Groups. See the following Section 3-B-7.03 ‘Uniform Call Distribution (UCD) Group” for details on UCD Groups. 3-B-l 2 Reference VT 1 Dumb 19-E-3.00 Il0-G17.00 / - 7.04 Paging Group 7.05 Trunk Group Description Description It is possible to execute paging functions in a group composed of one or more pickup groups. Such a group is called a “Paging Group.” To support efficient utilization of trunks, they can be grouped together (up to 16 groups) if all Up to eight paging groups can be assigned in the system. When Tenant Service is employed, the ‘GroupICM/Paging Group” screen sets which tenant the paging group belongs to. The “Group-Call Pickup Group” screen sets which pickup group(s) make up a paging group. Programming 1 System Programming “Group-ICMIPaging Group”, Paging GroupTenant ‘Group-Call Pickup Group”, PAG Reference VT 1 Dumb 9-E-2.00 10-C-16.00 9-E-3.00 10-G17.00 Conditions If tenant service is employed, pickup groups which can be used to configure a paging group are limited within the same tenant. See Section 4-H-l .OO “Paging” for further information about paging features. trunks in the group perform the same function. The following six kinds of trunk groups can be assigned in the system. The items listed below are set in the “GroupTrunk Group” screen. Trunk group type Trunk group name Tenant selection Trunk group direction Incoming destination (Day) i; Incoming destination (Night) Intercept Routing (Day) (W Intercept Routing (Night) restriction level Ij! Toll Toll restriction table WI Dialing plan selection (1) Disconnect time selection (m) Pause time selection (n) Hookswitch flash time selection (0) DID digit modification‘table selection (p) Entry of PBX access code (No restriction) ( q ) Entry of PBX access code (Restriction) (r) Restriction time on CO-CO calls (s) DIL (I:N) destination (t) Maximum number of digits after External Feature Access (u) CO-TIE Restriction (v) TIE-CO Restriction (w) TIE Forced Account Mode (x) TIE Incoming Delete Digit (y) TIE Incoming Insert Dial (4 lb) 6) (d) The “Trunk-CO Line”, Trunk Group determines which trunk group the CO line belongs to. Programming ‘Trunk-CO Line”, Trunk Group Conditions A single CO line cannot belong to more than one trunk group. 3-B-l 3 (70695) 9.00 Mixed Station Capacities Programming Description The KX-T336 System supports a wide range of telephone sets, not only PITS (Proprietary integrated Telephone System) telephones but also Standard Rotary telephones (10 pps/20 pps) and Standard Push-button telephones. The PITS telephones can be categorized as follows: System Reference Duinb VT “Configuration-Slot Assignmenr S-C-2.00 10-C-2.00 Conditions None KX-T308 system : KX-T30820 KX-T30830 KX-T30850 KX-T616 system : KX-I61620 KX-T6 1630 KX-T61650 KX-T1232 system: KX-Tl23220 KX-Tl23230 KX-T12323OD KX-T123235 KX-T123250 KX-T7000 Programming series ‘: KX-T7020 KX-T7030 KX-DO50 KX-T/130 Hybrid Line Circuits (HLC) card or Proprietary ITS Line Circuits (PLC) card are required for PITS telephones. Hybrid Line Circuits (HLC) card or Single Line Circuits (SLC) card ark required for single line telephones. The ‘Configuration-Slot Assignment” screen defines which card is installed in which slot. 3-B-l 9 10.00 Variable Time-Out Description Programming The timer values listed below can be set and changed in system programming. Common system timer values are set by the “System-System Timer” screen and “Special Attendant-DISA” screen. The timer values used with each trunk group are set by the “GroupTrunk Group” screen and the timer values used by the CO lines are set by the “Trunk-CO Line” screen. The timer values used with each extension are set by the “Extension-Station” screen. System timer values: cl> Held Call Reminder e2> Held Call Reminder (Attendant) <3> Transfer Recall <4> Pickup Dial Waiting <5> External First Digit Time-Out c6> External Interdigit Time-Out <7> External‘lnterdigit Time-Out (PBX) <8> Toll Restriction Guard Time-Out <9> Call Forwarding-No Answer Time-Out cl Q> Intercept Routing-No Answer Time-Out (System) cl 1s Intercept Routing-No Answer lime-out (DISA) cl 2> Attendant Overflow Time cl 3~ SMDR Duration Time cl 4> TIE Interdigit Time-Out ~15~ Delayed Answer (DISA) ~16s Prolonged Time (DISA) <17> Automatic Redial Retry Interval (WSl) <18> First Dial Timer (WS2) <19> First Dial Timer (DID) (WS2) System “System-System Timer” ‘Special Attended-DISA”, Delayed Answer Prolong Time “Group-Trunk Group”, CO-CO Duration Limit Disconnect Time Pause Time Hook Switch Flash lime “Trunk-CO tine”, DTMF Duration Time CPC Detection Wink Signal Time-Out ‘Extension-Station”, Day Ring Night Ring “World Select 1 (WSl)” Automatic Redial Retry Interval ‘World Select 2 (WS2)” First Dial Timer First Dial Timer (DID) Conditions None Trunk group timer values: cl> CO-CO Duration Limit <2> Disconnect Time c3> Pause Time <4> Hook Switch Flash Time CO Line timer values: xl> DTMF Duration Time <2> CPC Detection Time (Incoming) c3> Wink Singnal Time-Out Station timer values: cl> Delayed Ringing (Day/Night) 3-B-20 (7Q695)M mce Dumb Programming 9-D-3.00 9-K-l .OO Io-c-8.00 IO-c-40.00 9 - E - l .Ol I o-c-1 4.00 9-F-l .OO I O-C-I 8.00 9 - G - l .02 1 o-c-22.oc - 1 o-c-51 .oc - 1 O-C-52.0( Note: *’ This feature works if the extension user goes off-hook while the alarm tone is ringing for 2 minutes. ** Tenant Service If the tenant service is employed, each tenant (1 and 2) can have its unique wake-up message respectively. In this case, afflications of the wake-up message and the extension should be the same tenant. l l 3 Operating Status Refer to Section 14-C-2.00 “Definition of Operating Status.” ’ OGM busy Up to four extensions per DISA card can initially receive a wake-up message at a time. *5 BGM To utilize BGM, set the usage of music source to “BGM” or “Hold (Refer to Section 9-F-2.00 “Pager and Music Source.“) & BGM.” *6 From BGM to a wake-up message The extension who currently hears BGM will hear the wake-up message instead of BGM when: l l Next playback of the message begins. A DISA resource is released, that is, the extension user goes on-hook after hearing the message. 3-F-66 (40993) 14.00 TIE Lines Description A TIE line is a privately leased communication line between two or more PBXs, which provides cost effective communications between company members at different locations. TIE lines can be used to call through KX-T336 to reach another switching system (PBX or CO). By utilizing the TIE lines, the KXT336 can support not only communications with the public network but with other locations of the company in the private network which your KX-T336 can be a part of. To make a call to a person in .a distant company location, an extension user must first obtain the appropriate TIE line to that person’s PBX, and then dial the extension number only or a location number plus extension number. A Network of TIE Lines 1 .Interfaced KX-T336 by a TIE (E&M) channel of T-l DIGITAL TRUNK card (Digital) KX-T336 or other manufacturers’ PBX Hardware Requirements: T-1 DIGITAL TRUNK card (KX-T96187) Numbering Plan: Extension users can make a call over the TIE Line Network to other extension users in a distant location by one of the following procedures. 1. Extension Number only (See Section 3-F-14.01 .) ; Extension Number l CO (TIE) button + Extension Number l Trunk Group Access Number + Extension Number 2. Location Number (PBX Code) + Extension Number (See Section 3-F-14101 .) l l l TIE Trunk Access Code + v]+ Extension Number (co] button + [Code] + Extension Number Trunk Group Access Number + (WI+ Extension Number 3-F-67 (70695)M Routing Procedure 1: Routing Table Provides for the routing of calls over the TIE Line Network. Up to 36 routing patterns can be programmed in this table. This table is referenced by the system to identify the trunk route, when an extension user made a TIE call by dialing the feature number for TIE Trunk Access,” or Other PBX extension number. A routing pattern appropriate for each call is decided by the first one, two or three digits (except TIE trunk access code) of the dialed number. . Routing Table Override If a TIE call is made by pressing a CO key or dialing Trunk Group Access Number, this table is not referenced by the system and the call is routed over the specified TIE trunk directly. {Programming Example) PBX-1 A Network of TIE Lines PBX-2 TlE Line TGlO p TGlO PBX Code 951 PBX Code 950 TIE Line Routina Table in PBX-1 Code Delete Digit 951 0 Insert Dial Trunk Group Hunt Sequence TO21 When “84’ (TIE Trunk Access Code)+951+100” is dialed by an extension user, the routing pattern for this call is decided by “961.’ Then the call is routed over TGlO (Trunk Group 10 whose type is “TIE”). * Default for Fixed 1. 3-F-68 (70695) 1 Routing Procedure 2: Routing Flow Chart (1) When a TIE call is made by an extension user in your PBX Analyzing extension dialed number 1 Extension TIEI for ? ‘es 1 II [Other PBX Extension? Yes in the TIE Routing Table? I Yes 1 Is TIE line selected by hunt No sequence allowed I by Trunk Group Access (COS)? l Yes Call i [Reorder to Extension 1 (Note) TRLE = Toll Restriction Level of Extension TRLT = Toll Restriction Level of Trunk Group 3-F-69 (70695) ie7 Routing Procedure 2: (2) When a TIE call comes in on your PBX from other PBXs. -1 4 No 1 IsthereaPBXCode 1 in the recr!rgits? 1 ] Does the leading 3digit of the received digits match your PBX Code? f Yes 1 I s y o u r PBx’sCO 1 No Is there a CO access code of your PBX in the received digits? 4 Yes Is “TIE-CO Re.striction” of the No -4 selected trunk group set to “Yes”? Calling to CO. 1 + Yes Is there your PBx’s extension number in the received digits? i I No Sends reorder tone. / Does the leading 3digit of the received digits match a “Code” in a Routing Table? I No Does that extension actually exist? making an outgoing TIE call is decided Is 3 - F - 7 0 (70695) +Sends reorder tone. 1 Programming (1) Basic Programming Always required to make use of TIE lines regardless of the type of applications. System Programming “Configuration - Slot Assignmenr “Configuration - Channel Assignmenr “Group -Trunk Group (l/2)“, Type “Trunk- CO Line”, Trunk Group World Select 1 (WSl)“, Flash Detect (TIE) Answer Decision Timer -I- Refc VT 9-c-2.00 9-c-4.00 9-E-l -01 9-F-l .OO - (2) Timer programming System Programming “System-System Timer”, TIE Interdigit Time-Out Reference VT 1 Dumb 1 O-c-6.00 (3) Application programming Programming items required vary depending on the type of application. Refer to Section S-F-1 4.01 through 14.05 for further information about each application programming. Conditions *The treatment of the TIE calls is the same as that of extension and CO calls. TIE calls can be put on hold, be transferred to/forwarded to other extensions or trunks (CO, TIE). 3-F-71 (70695)M 14.01 Calling from TIE to TIE Description TIE calls among several different company locations can be done by dialing a 3 or 4-digit extension number only, or by dialing a location number (PBX Code) and an extension number. (1) By dialing Extension Number only Description Extension users can make a call via TIE line to other extension users in other PBXs within a private network by simply dialing a 3 or 4-digit extension number. A Network of TIE Lines PBX-1 PEX code: None PBX-2 TIE Line TGlO - Extension numbers 100 - 199 TGlO PBX code: None Extension numbers 200 - 299 Ext. 100 Call Flow 1. Ext.1 00 dials 200. 2. Ext.100 is connected to Ext.200 of PBX-2. Programming example: To make up the TIE Line Network above, the following system programming is required at PBX-1 and -2 respectively. PBX-1 . System - Operation (l/3)-PBX Code: (Blank) . System - Numbering Plan (9-D-6.00, 1 O-C-l 0.00) 1 st Hundred Extension 1 Other PBX Extension 01 2 . Special Attended - TIE Line Routing Table (9K4.00,10-C-65.01) No. 01 PBXQ l l l Code 2xX’ Delete Digit Insert Dial 0 Trunk Group Hunt Sequence 01 02 10 System - Operation (l/3)-PBX Code: (Blank) System - Numbering Plan 1st Hundred Extension 2 Other PBX Extension 01 1 Special Attended - TIE Line Routing Table No. 01 Code lxx Delete Digit Insert Dial 0 01 10 3-F-72 (70695) Trunk Group Hunt Sequence 02 Programming System Programming ” System-Operation( 1/ 3)“. Numbering Plan “System-Numbering Plan” , TIE Trunk Access Other PBX Extension 01-16 “Special Attended-TIE Line Routing Table”, Code Delete Digit Insert Dial Trunk Group Hunt Sequence 01-05 Reference VT Dumb 9-D-l .Ol 10-c-4.00 9-D-6.00 9-D-6.10 10-C-l 0.00 9-D-6.11 9-K-4.00 1 O-C-65.01 (2) By dialing Location Number (PBX code) and Extension Number Description Extension users can make a call to other extension users in other PBXs within a TIE line network by dialing a location number (PBX Code) and an extension number. Each PBX in the same TIE Line Network can have its own flexible extension numbering plan. A Network of TIE Lines P B X - 1 PBX-2 I TGlO TIE tine - PBX Code 950 1 TGlO I PBX Code 951 - Ext. 100 Call Flow 1. Ext.100 of PBX-1 dials 34-951-100. 2. Ext.100 of PBX-1 is connected to Ext.100 of PBX-2. Programming example To make up the TIE Line Network above, the following system programming required at PBX-1 and -2 respectively. PBX-1 l l l System -Operation (l/3) (9-D-l .01,10-C-4.00) PBX Code: 950 System - Numbering Plan (OI/ll)-TIE Trunk Access: 34 (default) Special Attended - TIE Line Routing Table (9-K-4.00,1 O-C-65.01) 3-F-73 (70695) iS No. 01 02 PBXB l l l Code Delete Digit 951 01 0 Trunk Group Hunt Sequence 02 10 . System - Operation (l/3) PBX Code: 951 System - Numbering Plan (07/11)-TIE Trunk Access: 84 (default) Special Attended - TIE Line Routing Table I Programming insert Dial Delete Digit Insert Dial 0 E Trunk Group Hunt Sequence 01 1 02 1 I I 10 System Programming “ System-Operation( 1/ 3)“, PBX Code “System-Numbering Plan”, TIE Trunk Access “Group-Trunk Group (2/2)“, TIE Incoming Delete Digit TIE Incoming Insert Dial “Special Attended-TIE Line Routing Table”, Code Delete Digit Insert Dial Trunk Group Hunt Sequence 01-05 “TIE Trunk Relay Restriction (TRR) 3-F-74 (70695) 9-D-6.10 9-E-l .02 1 O-c-1 5.00 9-K-4.00 10-c-65.01 1 O-c-65.03 -. Operation Maiking a TIE call (A) By dialing an extension number 1 .Lift the handset or press the SP-PHONE button. - You hear dial tone 1 or 3 or 4, 2.Dial the other PBX’s extension number. . You hear ringback tone. (B) By dialing a PBX code and an extension number 1 .Lift the handset or press the SP-PHONE button. - You hear dial tone 1 or 3 or 4. 2.Dial the feature number for TIE Trunk Access - You hear dial tone 1. 111 EEI .S. 7.. * “34” (default). 3.Dial the PBX code of the destination PBX and then the extension number of your destination parry - You hear rfngback tone. 3-F-75 (70595) . 14.02 Calling from TIE to CO Description TIE Lines can be used to minimize the cost of calls to a distant location outside of the TIE Line Network. A long distance call from one location may be a local call from another location. This fact must be taken into consideration before making a long distance call. If the destination of the long distance call is outside of the TIE Line Network, extension users first call to a distant PBX via TIE Line and then can make .a local CO call to the final destination through that PBX. A Network of TIE Lines c------------_-----------I PBX-1 I I I I i I I i i i Ext. 100 Inside of the TIE Line Network ; L-,-,---,,--,,-,--,--,--,- .i Call Flow 1. Ext.100 dials 64-951-g (TIE Trunk Access Code + PBX Code + CO Access Code). 2. Ext.1 00 is required to enter a TIE account code*. 3. Ext.100 hears dial tone from an idle CO line of PBX-2. 4. Ext.100 dials xxx-xxxx (phone number of the outside party). *Step 2 is required when “TIE Forced Account Code” Mode is set to “Yes” at PBX-2: Programming example: To make up the TIE Line Network above, the following system programming is required at PBX-1 and -2 respectively. PBX-1 l l System - Operation (l/3) (9-D-l .Ol , 1 O-C-4.00) PBX Code: 950 Special Attended - TIE Line Routing Table (9-K-4.00, 10-C-65.01) No. 01 Code 951 Delete Digit Insert Dial 0 01 10 02 . 3-F-76 (70695) Trunk Group Hunt Sequence 02 PBX-2 l l l System - Operation (l/3) PBX Code: 951 Group - Trunk Group (2/2) (9-E-l .02, 1 O-C-l 5.00) Type: TIE TIE - CO Restriction: No TIE-Forced Account Code Mode: Yes Special Attended - TIE Line Routing Table No. 01 02 Programming Code 950 Delete Digit Insert Dial 0 01 02 10 -I System Programming “Group-Trunk Group (2/2)“, TIE-CO Restriction TIE-Forced Account Code Mode TIE Incoming Delete Digit TIE Incoming insert Dial “Special Attended-TIE Line Routing Table”, Code Delete Digit Insert Dial Trunk Group Hunt Sequence 01-05 “TIE Account Code (TAC)” “TIE Trunk Relay Restriction (TRR) Conditions Trunk Group Hunt Sequence Reference VT Dumb 9-E-1.02 10-c-15.00 9-K-4.00 10-c-65.01 1 O-C-65.02 1 o-c-65.06 1 .TIE-CO Restriction Used to restrict or not extension users from ‘Calling from TIE to To restrict, set to “Yes.” To allow, set to ‘No.” CO." 2.TIE Account Code Used to allow certain extension users “Calling from TIE to CO.” If “Forced Account Mode” of the trunk group is set to “Yes”, an extension user must enter a valid TIE account code before ‘Calling from TIE to COP TIE Account Codes can be registered by using TAC command in the Dumb Programming mode. (Refer to Section 1 O-C-65.02 “TIE Account Code.“) 3.“Calling from TIE to CO” is available only when your system employs Code (Location number) method for making/receiving TIE calls. 3-F-77 (70695) PBX Operation 1 .Lift the handset or press the SP-PHONE button. - You hear dial tone 1 or 3 or 4. 2.Dial the feature number for TIE Trunk Access - You hear dial tone 1, “84” (default). 3.Dial the PBX code and a CO access code of the destination PBX. 4.Dial a TIE Account Code (if required). 5.Dial the telephone number of the outside party. 3-F-78 (70895) 14.03 Calling from CO to TIE Description TIE lines are usually used to link two or more distant locations where high volume calling traffic exists. However, a person at a location outside of the Tie Line Network can also use it by first making a CO call via public network to the nearest point of TIE Line Network for the purpose of saving the toll call charge. A Network of TIE Lines c------___---___-_-------PBX-1 i PBX-2 i TIE Line i TGlO ! . DISA I PBX Code 950 i I Employee-l PBX Code 951 Ext. 100 Call Flow 1. Employee-l at a local branch makes a CO call to PBX-1 via DISA. 2. Employee-l dials “84” (TIE trunk access code). 3. After hearing dial tone, Employee-l -dials 951-100. 4. Employee-l at a local branch will be connected to Ext.1 00 of PBX-2. . Programming example: To make up the TIE Line Network above, the following system programming is required at PBX-1 and -2 respectively. PBX-1 System -Operation (l/3) (9-D-l .Ol , 10-C-4.00) PBX Code: 950 l Group - Trunk Group (2/2) (9E-1.02,1 CO-TIE Restriction: No’ l l l O-C-1 5.00) This assignment is required at the trunk group whose ‘Incoming Mode” is set to ‘DISA”. Special Attended - TIE Line Routing Table No. 01 02 .. Code Delete Digit 951 Insert Dial 0 01 10 3-F-79 (70695) i I 1 i I Inside of the TlE tine Network i TGlO Trunk Group Hunt Sequence 02 . PBX-2 l System - Operation (l/3) PBX Code: 951 l Special Attended - TIE Line Routing Table No. 01 02 Programming Code 950 Delete Digit insert Dial 0 Trunk Group Hunt Sequence 01 10 Reference VT Dumb System Programming “Group-Trunk Group (2/ 2)“, CO-TIE Restriction TIE Incoming Delete Digit TIE Incoming Insert Dial “Special Attended-TIE Line Routing Table”, Code Delete Digit Insert Dial Trunk Group Hunt Sequence 01-05 “TIE Trunk Relay Restriction (TRR) Operation 02 9-E-1.02 10-c-15.00 9-K-4.00 10-C-65.01 10-C-65.03 1 .Dial the DISA phone number. * You hear ringback tone. 2.You hear the DlSA outgoing message. 3.Dial the feature number for TIE Trunk Access ‘84” (default). 4.Dial the PBX code of other PBX and then the extension number of your party. - You hear ringback tone. 3-F-80 (70695) 14.04 Alternate Routing Description When more than two PBXs at different locations are interconnected with a network of TIE Lines, your KX-T336 works as an intermediate switching office to other PBXs in the network by relaying tie calls from one PBX to another. A problem of telephone switching is that blocking sometimes occurs on the network, and a call cannot be switched as required because all the lines on a given route are occupied or unavailable. By utilizing this relay function, several alternative routes can be set up beforehand in addition to the primary-route. This permits TIE calls to be routed from “A to B” or “A through C to B” and so on. If the primary-route is poor because of equipment failure or congestion, KXT336 bypasses it and selects the secondary-route. On receipt of a TIE call, KX-T336 analyzes it to determine the destination to which the call must be sent or the route by which the calls will be sent, and then transmit it. Alternate Routing makes a TIE Line Network more flexible in adapting to peaks of traffic and it provides a variety of different routing plans. A Network of TIE Lines PBX-2 PBX-1 IPBX Code: 9531 PBX-3 yr///( : Primary-route m : Secondary-route Call Flow 1 Ext.1 00 dials “84+952+200.” 2.When “952 is found in the table,TGlO (Hunt Sequence 01 for “952”) is selected automatically. l If TGlO is not available, TGll (Hunt Sequence 02) will be selected. In this case, the call is sent to PBX-2 via PBX-3 and -4. The treatment of the call is decided by Routing Table of PBX-3 and then PBX-4. 3.The call is sent to PBX-2. 3-F-81 (70695) Programming example: To realize the call flow mentioned in the previous page, the following system programming is required at PBX-1, -3, and -4 respectively. PBX-1 l l l PBX-3 l l System -Operation (l/3) (9-D-l .Ol , 1 O-C-4.00) PBX Code: 951 . Special Attended - TIE Line Routing Table (9-K-4.00, 10-C-65.01) No. Code Delete Digit 01 02 . 952 953 0 insert Dial Trunk Group Hunt Sequence 01 02 10 11 11 10 TIE Trunk Relay Restriction (TRR) (10-C-65.03) System -Operation (l/3) PBX Code: 953 Special Attended - TIE Line Routing Table No. 01 02 . Code 952 Delete Digit Insert Dial 0 T01 Trunk Group Hunt Sequence 02 12 tr l PBX-4 l l TIE Trunk Relay Restriction (TRR) System -Operation (l/3) PBX Code: 954 Special Attended - TIE Line Routing Table No. 01 02 .. Code 952 Delete Digit Insert Dial 0 01 Trunk Group Hunt Sequence 02 13 TIE Trunk Relay Restriction (TRR) Note: If you want to restrict %all relay from PBX-1 to PBX-2 via PBX-r, set ‘TGll” to ‘Yes” at PBX-3 using TRR command. l 3-F-82 (70695) Programming System Programming “Group-Trunk Group (2/ 2)“, CO-TIE Restriction TIE-CO Restriction TIE incoming Delete Digit TIE incoming Insert Dial “Special Attended-TIE Line Routing Table”, Code Delete Digit Insert Dial Trunk Group Hunt Sequence 01-05 “TIE Trunk Relay Restriction (TRR) 3-F-83 (70695) T Refc ence Dumb VT lo-c-15.00 9-E-l .02 . 9-K-4.00 1 O-C-65.01 1 O-C-65.03 15.00 T-l Carrier Description The T-l carrier is a hierarchy of digital systems designed to carry approxil .544 Mbps. speech and other signals in digital form. The T-l carrier has 24 PCM (Pulse Code Modulation) voice channels. T-l DIGITAL TRUNK Card (KX-T96187) and CSU (Channel Service Unit) are required to utilize T-l carrier with KX-T336 System. This card supports five different trunk interfaces to provide desired connection at minimum expense. One of the following five trunk types can be assigned to one of 24 voice channels of T-l DIGITAL TRUNK card individually according to tariffs and customer need. type of interface : LCO/GCO/DID/OPX/TIE T-l line The installer must arrange for the following parameters with the Central Office or T-l provider: Type of Interface: LCO/GCO/DlD/OPX/TlE, Frame format: D4 (SF)/ESF Line coding: AMI/B8ZS, Signaling: DP/DTMF CSU (Channel Service Unit) The installer must provide a CSU to connect the T-l line to the KX-T96187. The CSU must support the following functions: : Protection for the Central Office line : Loop Back : Performance Monitoring Programming System Programming Reference VT 1 Dumb 9-c-2.00 “Configuration - Slot Assignmenr 9-c-3.00 ‘Configuration - DN AssignmeW “Configuration - Channel Assignmenr 9-c-4.01 T-l card ‘System Clock Mode (CLK) ~ “Master Clock Priority (CLP) “ESF Frame Option (EFO) Description 1 o-C-2.00 1 O-c-3.01 1 O-C-64.01 1 O-C-64.02 1 O-C-64.03 1 o-c-64.04 (1) Up to six T-l DIGITAL TRUNK cards (144 ports) can be installed to the system under the following conditions. System Configuration 1 HLC+PLC+SLC+OPX+DID+LCOT+ 12 1 cards ’ --I (96 ports) GCOT+T-1 Expansion shelf HLC+PLC+SLC+OPX+DID+LCOT+ 15 cards (120 ports)’ GCOT+T-1 Fully Expanded HLC+PLC+SLC+OPX+DID+LCOT+ 42 cards (336 ports)’ GCOT+T-1 system Basic shelf ‘T-l is counted as 3 cards. 3-F-84 (70695)M (2) Physical port number for each T-l trunk channel is as follows: Sllot No. Slot 01 Slot 0 5 Slot 0 9 T-l Channel c h 01-08 ch 09-16 ch 17-24 c h 01-08 ch 09-16 ch 17-24 c h 01-08 ch 09-l 6 c h 17-24 X: Shelf No. (1 =Basic, 2=Expansion Port No. X011-X018 X021 -X028 X031 -X038 X051 -X058 X061 -X068 X071 -X078 X091 -X098 X101-X108 X111-X118 1, 3=Expansion 2) (3) DN Assignment is required when a channel of T-l card is assinged as ‘OPX. (4) Select the external clock mode, if your system is interfaced by T-l interface with another exchange. Refer to Section 1 O-C-64.02 ‘System Clock Mode (CLK)” and Section 1 O-C-64.03 “Master Clock Priority (CLP).” Maintenance The following two test commands are provided for T-l DIGITAL TRUNK Card. l l Loop Back Test (LBT) - Section 15-E-3.01 DTMF-Generator/Receiver Test (DTM) - Section 15-E-3.02 3-F-85 (70695)M 16.00 Limited Call Duration Description Limited Call Duration is a system programmable feature that disconnects a CO call when a pre-specified time expires. A warning tone is sent to the extension user 15 seconds before the time limit. Limiting the call duration can be enabled or disabled on a COS (Class of Service) basis for each extension. Programming Reference VT I Dumb System Programming “Limited Call Duration (LCD)” Conditions l l l j - / 10-c-69.00 / This feature applies to incoming CO calls only, outgoing CO calls only or both incoming and outgoing CO calls depending on the system programming. Call duration time limit is ranging from 01 to 60 minutes depending on the system programming. Call duration time of any CO call (except a CO-to-CO call) can be limited by this feature. CO-to-CO Call Duration timer applies to a CO-to-CO call. l This feature does not apply to CO calls to/from an Attendant Console. l This feature is available with the following version of the software. V.12.XX or higher version 3-F-86 (70695)M _ 4.00 5.00 6.00 . . 7.00 8.00 9.00 10.00 Automatic Dialing ................................................................................... 4.01 One Touch Dialing ....................................................................... 4.02 Speed Dialing-System ................................................................. 4.03 Last Number Redial (LNR) .......................................................... 4.04 Automatic Redial ......................................................................... 4.05 Saved Number Redial (SNR) ...................................................... Making Internal Calls ............................................................................. 5.01 Inter Office Calling ....................................................................... 5.02 Intercom Calling ........................................................................... 5.03 Intercom-Voice Calling ................................................................. 5.04 Intercom-Busy Station Signaling (BSS) ....................................... 5.05 Intercom Off-Hook Call Announcement (OHCA). ........................ Automatic Callback ................................................................................ 6.01 Automatic Callbatik-Trunk ........................................................... 6.02 Automatic Callback-Station ......................................................... Executive Busy Override ....................................................................... Do Not Disturb (DND) Override ............................................................. Walking COS (Class of Service) ............................................................ Operator Call ......................................................................................... D Receiving Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 .oo 2.00 3.00 4.00 5.00 6.00 7.00 8.00 .............................................................. i.. ............................... Line Selection-Answering .................................... 1 .Ol Ringing Line Preference-Answering.. .......................................... 1.02 Prime Line Preference-Answering ............................................... 1.03 No Line Preference-Answering .................................................... 1.04 Direct Answering (Pre-selection) ................................................. Intercom Answer .................................................................................... 2.01 Intercom Hands-Free Answerback .............................................. 2.02 Intercom Answer Voice Calling Deny .......................................... 2.03 Intercom Answer BSS/OHCA Deny ............................................. Call Pickup ............................................................................................. . ............... 3.01 Dial Call Pickup ........................................................... .................................................................... 3.02 Directed Call Pickup 3.03 Call Pickup Deny ......................................................................... Trunk Answer From Any Station (TAFAS)-Day Service.. ....................... Executive Busy Override Deny.. ............................................................ Do Not Disturb (DND) ........................................................................... Call Waiting ............................................................................................ Uniform Call Distribution (UCD)-Log Out ................................. ..> ........... 4-2 Page 4-c-1 0 4-c-1 0 4-c-1 1 4-c-1 4 4-c-1 5 4-C-l 6 4-c-1 7 4-c-1 7 4-C-l 8 4-c-1 9 4-C-20 4-C-21 4-c-22 4-C-22 4-C-24 4-C-25 4-C-26 4-C-27 4-C-28 4-D-l 4-D-l 4-D-l 4-D-2 4-D-3 4-D-3 4-D-4 4-D-4 4-D-5 4-D-6 4-D-7 4-D-7 4-D-8 4-D-9 4-D-10 4-D-11 4-D-l 2 4-D-15 4-D-l 7 . E Holding Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 .OO Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.00 Consultation Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.00 Call Hold Retrieve-Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.00 Call Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.01 Call Park-System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.02 Call Park-Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.00 Call Split ing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-E-l 4-E-2 4-E-3 4-E-5 4-E-6 4-E-6 4-E-8 4-E-l 0 Transferring Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-F-l 1 .OO Call Transfer .......................................................................................... 1 .Ol Unscreened Call Transfer to Station ............................................ 1.02 Screened Call Transfer to Station.. .............................................. 1.03 Screened Call Transfer to Trunk .................................................. 1.04 Ringing Transfer.. ........................................................................ 1.05 Unscreened Call Transfer to Remote .......................................... 1.06 Unscreened Call Transfer to Attendant Console.. ....................... 1.07 Unscreened Call Transfer to a UCD Group (with OGM) ............. 2.00 Call Forwarding (FWD) ......................................................................... 2.01 Call Forwarding-All Calls ............................................................. 2.02 Call Forwarding-Busy/Off-Hook ................................................... 2.03 Calf Forwarding-No Answer ......................................................... 2.04 Call Forwarding-Busy/Off-Hook/No Answer.. .............................. 2.05 Call Forwarding to Trunk .............................................................. 2.06 Call Forwarding-Follow Me.. ........................................................ 4-F-l 4-F-l 4-F-2 4-F-3 4-F-4 4-F-5 4-F-5-l 4-F-5-2 4-F-6 4-F-6 4-F-9 4-F-l 2 4-F-l 5 4-F-18 4-F-21 Conversation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-G-l 2.00 Exclusive Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F G Page 4-E-l 1 .OO Programmable Privacy .......................................................................... 2.00 Privacy Release ..................................................................................... 3.00 Privacy Attach.. .................................................................. t.. ................. 4.00 Hands-Free Conversation ...................................................................... 5.00 Conference ............................................................................................ 5.01 Conference-One Appearance ...................................................... 5.02 Conference-Two Appearances .................................................... 6.09 Unattended Conference.. ....................................................................... 6.01 Unattended Conference-One Appearance .................................. 6.02 Unattended Conference-Two Appearances ............. ;. ................. 7.00 Doorphone ............................................................................................. 8.00 Flash ...................................................................................................... 9.00 External Feature Access ........................................................................ 10.00 Microphone Mute.. ................................................................................. 11 .OO intercom Off-Hook Call Announcement (OHCA) ................................... 12.00 Tone Through (End to End DTMF Signaling) ......................................... (7Z5) 4-G-l 4-G-2 4-G-3 4-G-4 4-G-5 4-G-5 4-G-7 4-G-9 4-G-9 4-G-l 1 4-G-13 4-G-14 4-G-l 5 4-G-16 4-G-l 7 4-G-l 8 . 2.05 Call Forwarding to Trunk Description Programming Call Forwarding to Trunk allows extension users who are away from their phones to receive incoming calls (both CO and extension) at outside place. System Programming ‘System-Class of Service (l/2) Call Forwarding/Do Not Disturb CO Forward Mode “System-Numbering Plan (04/l l)“, Call Forwarding-to Trunk ‘System-Numbering Plan (05/l 1)“. Call Forwardinq/Do Not Disturb Cancel “Group-Trunk Group (l/2)“, CO-CO Duration Limit The following incoming calls do not receive Call Forwarding treatment. . l l l l l A call appearing on ICM button A call from doorphone A call appearing on PC0 button A call routed via DIL 1: N feature A call directed to a UCD group When an incoming CO call is forwarded to the pre-assigned outside party by this feature, CO to CO call via this system is established. Duration time of CO to CO call is restricted by “GroupTrunk Group,” CO-CO Duration Limit of receiving CO line. The system sends alarm tone to both parties 15 seconds before the Duration Limit time is expired, and when expired the system disconnects both parties compulsively. To set Call Forwarding to Trunk, assign both “System-Class of Service”, Call Forwarding/Do Not Disturb and CO forward Mode to “Yes.” For setting and canceling this function, two methods are available: cl > By pressing the PWD/DND button. c2> By dialing the feature number for “Call Forwarding-to Trunk’ and ‘Call Forwarding/Do Not Disturb Cancel.” Rel VT 9-D-4.0’ 9-D-6.0‘ 9-D-6.0! S-E-1 .Ol Conditions To set or cancel this function, use the PDN button. An extension user may have only one type of Call Forwarding/Do Not Disturb feature in effect at any time. If a second type is assigned, the previously assigned type is canceled. The Operators (Attendant Console or Extension) can cancel the Call Forwarding/Do Not Disturb feature assigned to the extension users. Refer to Section 4-l-11 .OO ‘Remote Station Feature Control.” Up to 32 digits composed of ‘0 through 9” and “se” can be entered as the telephone number of the destination. CO line access code must be entered as the leading digit of each entry. Note: l If CPC signal is not supplied by the Central Office in your area, KX-T336 cannot detect the end of CO-CO call after one party disconnects the call. In this case, we recommend to use tone detection feature of AGC Card (See Section 1 OC-67.00 ‘DISAIAGC Tone Detection Mode (TDW”). 4-F-l 8 (70695) - The following table shows the results of the calls arriving at an extension setting this function depending on the conditions of the preset destination. Type of Call Arriving at Setting Extension Extension call Condition of Destination Forwarding Execution 0 Idle status Busy status Conditions except In Service * DID call 1 Call is forwarded to external destination. 91 x OIL (1 :I) or DISA call Idle status Result Call is placed on setting extension. 0 Call is forwarded to external destination. X Call is placed on setting extension. X Call is placed on setting extension. Idle status Busy status Conditions except In Service * I 0: Forwarding possible )( : Fon,varding impossible t- 4-F-l 9 Conditions are ‘Out of Service? “Fault” and ‘Pm-Installed.” See Section 14-C-Z&O2 ‘Port” for details. Operation Setting Call Forwarding to Trunk FWWDNII El Canceling Call Forwarding to Trunk 1. Lift the handset or press the SP-PHONE button. 1. Lift the handset or press the SP-PHONE button. 2 . Press the FVVDIDND button, then dial “5.” Or, dial the feature number for “Call Forwarding to Trunk.” 2 . Press the FWD/DND button, then dial “0.” Or, dial the feature number for “Call Forwarding/Do Not Disturb Cancel.” l l Dial the feature number for selecting the CO line and the telephone number of the destination and “V in succession. l l You hear confirmation tone 1 or 2 and then dial tone 1 or 3 or 4. If your PITS has a display, it shows: FWDIDND Cancel 3. Replace the handset or press the SP-PHONE button. You hear confirmation tone 1 or 2 and then dial tone 1 or 3 or 4. If your PITS has a display, it shows: (Supplement) Type SOand KX-17050 PITS telephones are not provided with the FWD/DND button. Only the PF3 button on them can be programmed to be the FWD/DND button. Refer to Section 9-G-l .03 “Station (3/3)” and Section 12-C-2.00 “PF Button Assignment” for further information. 1 FWD (CO) 92011234 ] If the assigned number exceeds the display capacity: 1FWD (CO) 9201123 & 1 Replace the handset or press the SP-PHONE button., l . The indicator on the fWD/DND button starts flashing. (Supplement) The system does not check the dialed number, toll restriction level, and the feature number for selecting a CO line when the extension user is setting this function. 4-F-20 2.06 Call Forwarding-Follow Me Description You can set the “Call Forwarding-All calls” feature from the destination extension. This is useful if you forget to set “Call Forwarding -All Calls” feature before you leave your desk or when you move from pm-set place to another. This feature can be enabled or disabled on a COS (Class of Service) basis. If enabled, an extension user can set this feature. ( FWD (From) Ext xxxx ] --I-- Directory number: three or four digits 4. Replace the handset or press the SP-PHONE button. Programming System The indicator on the FWD/DND button starts flashing at your own extension. l Programming ‘System-Numbering ptan (09/11)“. Call Forwarding-Follow Me Set Call Forwarding-Follow Me Cancel “Call Forwarding-Follow Me (CFM)” l t Rel VT S-D6.E Canceling “Call Forwarding-Follow Me” at the destination extension. 1. Lift the handset or press the SP-PHONE button. - l Conditions The indicator light flashing on the FWD/DND button goes out. . 2. Press the FWD/DND button, then dial ‘8.” Or, dial the feature number for Call Forwarding-Follow Me Cancel =* *a” (default). Same as ‘Call Forwarding-All Calls “(Section 4-F2101). Operation Setting ‘Call Forwarding-Follow Me” at the destination extension 1. Li the handset or press the SP-PHONE button. 3. Dial the directory number of your extension. l •l 2. Press the PWD/DND button, then dial ‘7. Or, dial the feature number for Call Forwarding-Follow Me Set ‘* * 7” (defauit). l 1 WD Cancel Exxx 7 l l You hear confirmation tone 1 or 2 and then dial tone 1 or 3 or 4. If your PITS has a display, it shows: [ 4. Replace the handset or press the SP-PHONE button. PRS 3. Dial the directory number of your extension. You hear confirmation tone 1 or 2 and then dial tone 1 or 3 or 4. If your PITS has a display, it shows: Note: You can cancel this feature at your own extension by following the same procedure as canceling other call forwarding features. 4-F-2 1 (70695) G. Conversation Features 1 .OO Programmable Privacy Description 2. In non-privacy system: The extension user can intrude on a busy line by pressing the red lit PDN, SDN or SC0 button, if the system is set to non-privacy. In default mode, the system is set to privacy. This means that a third party cannot intrude on a busy line. Pressing PDN Allows a three Allows a three party conver- party conversatia sation (ignored if conference trunk is unavailable1 It is administrable to make system privacy or nonprivacy by “System-Operation”, Privacy on DN Key. Programming “System-Operation (l/3)“, Privacy on ON Key Reference VT 1 Dumb 9-D-l .Ol Button Piessed SC0 (reorder tone sounds if conference trunk is unavailable Callback- Intruding on a busy line in non-privacy system 1 o-c4.00 The following example shows the procedure to be used by extension B whose SDN is owned by the PDN of extension A, who is talking with party C on the PDN button. The table shows the other party to be barged in by pressing the red lit PDN, SDN and Single CO buttons in the non-privacy system. SDN Cause Automatic Callback-Trunk * Operation Conditions PDN Pressing GCO or PC0 * Refer to Section 4-C-5.01 “Automatic Trunk.” Programming System Pressing SC0 or SON Extension A Extension C a-a l Z:EZSn::ng A call to be barged in A call on the SDN button owned by this PDN. Extension B l A call on PDN button which is owner (including SLT) of this SDN. cSDNO l A call on the pressed Single CO I button. Extension B has the SDN button owned by extension A’s PDN. The indicator on the SDN button of extension B is lit in red. 1. Press the SDN button (on extension B) lit in red. Privacy and non-privacy can be temporarily changed. For further details, refer to Section 4-G-2.00 “Privacy Release” and Section 4-G-3.00 ‘Privacy Attach.* Extension A In privacy and non-privacy system, pressing a button which is lit in red results in the following: 1. In privacy system: Pressing PDN or SDN Pressing SCO, GCO, or PC0 4-G-l Extension C D Transferring Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5-D-1 1 .OO Call Transfer .......................................................................................... 1 .Ol Unscreened Call Transfer to Station.. .......................................... 1.02 Screened Call Transfer to Station.. .............................................. 1.03 Unscreened Call Transfer to Remote.. ........................................ 1.04 Unscreened Call Transfer to Attendant Console.. ....................... 1.05 Unscreened Call Transfer to a UCD Group (with OGM) ............. 1.06 Screened Call Transfer to Trunk .................................................. 2.00 Call Forwarding (FWD) ......................................................................... 2.01 Call Fonrvarding-All Calls ............................................................. 2.02 Call Forwarding-Busy/Off-Hook ................................................... 2.03 Call Forwarding-No Answer ......................................................... 2.04 Call Forwarding-Busy/Off-Hook/No Answer ................................ 2.05 Call Forwarding to Trunk ............................................................. 2.06 Call Forwarding-Follow Me .......................................................... 5-D-l 5-D-l 5-D-2 5-D-3 5-D-3-l 5-D-3-2 5-D-3-3 5-D-4 5-D-4 5-D-7 5-D-l 0 5-D-l 3 5-D-i 6 5-D-19 E Conversation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F 1 .OO Conference ............................................................. . .............................. 2.00 Doorphone ............................................................................................. 3.00 External Feature Access ........................................................................ 5-E-l 5-E-2 5-E-3 Paging Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-F-l 1 .OO 5-F-l 5-F-l 5-F-3 5-F-5 5-F-7 5-F-8 2.00 G 5-E-l Paging .................................................................................................... 1 .Ol Paging All Extensions .................................................................. 1.02 Group Paging .............................................................................. 1.03 Paging External Pagers ............................................................... 1.04 Paging All Extensions and External Pagers ............................... Background Music (BGM) through External Pager ................................ Other Features ................................................................................................ 5-G-l 1 .oo 5-G-l 5-G-l 5-G-2 5-G-3 5-G-5 5-G-7 5-G-9 5-G-l 0 5-G-12 5-G-14 5-G-15 5-G-16 :-z. 4.00 5.00 6.00 7.00 8.00 9.00 Night Service ......................................................................................... 1 .Ol Universal Night Answer (UNA) .................................................... 1.02 Flexible Night Service .................................................................. 1.03 Switching o f Day/Night Mode ...................................................... Account Code Entry ............................................................................... Timed Reminder .................................................................................... Data Line Security ................................................................................. Absent Message Capability .................................................................. Message Waiting ................................................................................... Electronic Station Lock Out ................................................................... Assigned Feature Clear ......................................................................... Remote Station Feature Control ............................................................ . A. Outgoing Call Features 1 .OO Making Outside Calls 1 .Ol Local Trunk Dial Access Description Operation Allows extension users to make outgoing CO calls by automatic selection of an idle CO line. Dialing the feature number for ARS/Local CO Line Access” enables you to execute this function. F-l l Programming Reference ‘System-Operation (l/3)“, Automaiic Route Selection “System-Local Access Group”, Hunt Sequence ‘System-Numbering Plan w!1)“, . AFWLocal CO Line Access Ccinditions You hear dial tone 1 or 3 or 4. You hear dial tone 1.” 3 . Dial the telephone number of the outside party. Programming System l 2. Dial the feature number for ARWLocal CO Line Access “9” (default). To activate this feature, set ‘SystemOperation”,Automatic Route Selection to ‘No.” If set to “Yes,” ARS feature is activated instead of this feature. Refer to Section 3-C-2.00 “Automatic Route Selection (ARS)” for further information. I 1. Lift the handset . . An idle CO line available and hunting sequence is determined by the system programming “SystemLocal Access Group”, Hunt Sequence. If an extension user hears busy tone, there is no idle CO line available. If an extension user hears reorder tone, the user is restricted from accessing this feature. Refer to Section 3-C-l .Ol “Tot1 Restriction for Local Trunk Dial Access,” for further information. If tenant service is activated, accessible trunk group is limited to the trunk groups within the same tenant. (+ for U.S.A. and Canada only) The dialing plan followed is that of the trunk group in hunt sequence 01 in “System-Local Access Group.” S-A-1 (70695) D. Transferring Features 1 .OO Call Transfer 1 .Ol Unscreened Call Transfer to Station Description Transfer is convenient to redirect a call to another place. Attendant assistance is not required and the caller does not have to redial. SLT Transfer Operation When SLT Transfer Operation mode is set to “Mode 2”, an SLT user can transfer a call to an outside party. Reference l Section 5-D-l .06 “Screened call Transfer to Trunk” l Section 1 O-C-53.00 “World Select 3n Description Allows an extension user to transfer calls (both extension and outside calls) to another extension without announcement. Programming gggg+fq Conditions If transferred call is not answered by the destination party, it will receive one of the following treatments. %us of Destination Operation Resulted - Able to receive the call (sending ringback tone) Performs the call to the destination for a specific period. In case of no answer, interrupts ringing and starts ringing to the originator of transfer. 4 For detail, refer to Section 3-E-3.00 Transfer Recall.” BUSY (sending busy tone) As soon as the destination goes onhook, starts calling the destination (Camp-on Transfer). If the destination party remains busy or does not answer the call within a specified period, starts calling back the originator of transfer. *l For detail, refer to Section 3-E-3.00 “Transfer Recafl: Unscreened Call Transfer to extension Setting Do Not is ineffective. Dllturb (sending DND tone) Transferred party is treated simply as a party placed on Consultation Hold. Hanging up causes the Consultation Hold Recall to the originator of transfer When the originator of transfer answers the call, 4 conversation b&men the originator and the transferred party starts. The extension users can not transfer the following calls. l l 5-D-1 (70695) A call with Attendant Console A call with Doorphone If Music on Hold is available, from the start transferring operation until the destination answers, the system sends Music on Hold Section 3-E-l .OO “Music on Hold,“) to the while he or she is being transferred. of the party (See party Operation -2 (Mode 2) While having a conversation; 1. Press the switchhook for approximately one half second and release it. Instead of Music on Hold, Ringback Tone can be sent to the caller while he or she is being transferred (See Section 1 O-C-53.00 “World Select 3 (WS3)“). l l Operation -1 (Mode 1) While having a conversation; 2. Dial the feature number for Transfer “58” (default). 1. Press the switchhook for approximately one half second and release it. l l l The other party is placed on Consultation Hold. You hear confirmation tone 2 and then dial tone 1 or 3 or 4. l 2. Dial the directory number of the destination: three or four digits. l Note: l If you want to return to the held party, press the switchhook for approximately one’half second and release it before the destination extension answers. You hear ringback tone. Ringing starts at the destination extension. 4. Replace the handset. You hear ringback tone. Ringback starts at the destination extention. 3. Replace the handset. You hear confirmation tone 2 and then dial tone. 3. Dial the directory number of the destination: there or four digits. l l The other party is placed on Consultation Hold. You hear confirmation tone 2 and then dial tone 1 or 3 or 4. Note: l It the feature number for “Transfer” is not dialed at step 2, the call will be disconnected after replacing the handset. l 5-D-l-l (70695) If you want to return to the held party at step 3 above, press the swftchhook for approximately one half second and release it before the destination extension answers. - . 1.02 Screened Call Transfer to Station Description 4. Replace the handset. Allows an extension user to transfer the calls (both extension and outside calls) to another extension with announcement. Programming System Programming c I vT Reference 1 Dumb I “World Select 3(WS3)’ SLT Transfer Operation l The call is transferred to the destination. Note: If you want to return to the held party, press the switchhook for approximately one half second and release before the destination extension answers. Operation - 2 (Mode 2) Conditions While having a conversation: The extension user cannot transfer the following calls. l l 1. Press the switchhook for approximately one half second and release it. A call with Attendant Console A call with Doorphone l If Music on Hold is assigned, Music on Hold is sent to the transferred party since the party starts being transferred until he starts conversation with the destination party. For further detail, refer to Section 3-E-l .OO “Music on Hold.” l 2 . Dial the feature number for Transfer ‘58” (Default). l You hear confirmation tone 2 and then dial tone. The user can execute this function even after holding another party. 3 . Dial the directory number of the destination: there or four digits. l You hear ringback tone. Operation - 1 (Mode 1) While having a conversation; Press the switchhook for approximately one half second and release it. l l The other party is placed on Consultation Hold. You hear confirmation tone 2 and then dial tone 1 or 3 or 4, Wait for the answer and announce. The other party is placed on Consultation Hold. You hear confirmation tone 2 and then dial tone 1 or 3 or 4. 5 . Replace the handset. l The call is transferred to the destination. Dial the directory number of the destination: three or four digits. l You hear ringback tone. Wait for the answer and announce. Note: *If you want to return to the held party, press the switchhook for approximately one half second and release it before the destination extention answers. *If the feature number for “Transfer” is not dialed at step 2, the call will be disconnected after replacing the handset. 5-D-2 (70695) 1.03 Unscreened Call Transfer to Remote Description 2. Dial the “FDN for Remote”: three or four digits. Allows an extension user to transfer-a call to the remote maintenance resource. (Available with Software Version 9.5X and above). Modem answer tone is returned instantly, if it is not in use. This operation allows System Administrator to perform System Administration from Remote Location. Refer to Section 14-B-2.00 “System . Administration from a Remote Location” for further information. To transfer a call to remote maintenance resource, ‘FDN for Remote” is used, which is assigned in ‘System-Operation”, Remote Directory Number. See Section 3-B-3.00 ‘Floating Directory Number (FDN)” for details of FDN. J l l 3. Replace the handset. Operation -2 (Mode 2) While having a conversation; 1. Press the switchhook for approximately one half second and release it. Programming l l - The other party is placed on Consultation Hold. You hear confirmation tone 3, then dial tone 1 or 3 or 4. 2. Dial the feature number for Transfer “58” (Default). Conditions If Music on Hold is assigned, the system sends Music on Hold to the transferred party during the transferring operation. For details, refer to Section 3-E-l .OO “Music on Hold.“. l l l Operation -1 (Mode 1) While having a conversation; 1. Press the switchhook for approximately one half second and release it. l l You hear confirmation tone 2 and then dial tone. 3. Dial the ‘FDN for Remote”: three or four digits. If the remote maintenance port is in use, busy tone is returned to the held party. Automatic Callback does not function in this case, so the caller should call again when it becomes idle. 1 You hear confirmation tone 3, then dial tone 1 or 3 or 4. If the remote maintenance port is not in use, the held party hears answer tone and can start communication instantly. You hear confirmation tone 3,then dial tone 1 or 3 or 4. If the remote maintenance port is not in use, the held party hears answer tone and can start communication instantly. 4. Replace the handset. The other party is placed on Consultation Hold. You hear confirmation tone 2, then dial tone 1 or 3 or 4. 5-D-3 (70695) 1.04 Unscreened Call Transfer -to Attendant Console Description 1. Press the switchhook for approximately one half second and release it. . l The other party is put on Consultation Hold. l You hear confirmation tone 2 and then dial tone 1 or 3 or 4. 2 . Make a call to an Attendant Console. l You hear ringback tone. l Calling an Attendant Console starts. 3 . Replace the handset. l At an Attendant Console: The call is displayed as a transfer recall. Allows an extension user to transfer calls (both extension and outside) to an Attendant Console without announcement. Programming System I Programming Vl T- ‘World Select 3(WS3)’ SLT Transfer Operation Reference 1 Dumb 1 _ I I 10-c-53.00 I Conditions 1) Transfer Recall A call transferred by this feature will not ring back at the extension who transferred the call even if the Attendant Console does not answer the call after the transfer recall timer has been elapsed. 2) Intercept Routing No Answer (IRNA) A call transferred to an Attendant Console will not be transferred to another extension by IRNA feature even if the Attendant Console does not answer the call after the IRNA timer has been elapse@ 3) What if all six Loop keys on the Attendant Console are not idle? A call is put in the call waiting queue of the Attendant Console. 4) What if the Attendant Console is in ATT-FWD mode? This feature does not function.’ A call is simply put on Consultation Hold, that is, a call will ring back at the extension who tries to transfer the call as soon as he or she goes on-hook. 5) Music on Hold If Music on Hold is available, the system sends Music on Hold to the transferred party, from the start of the transferring operation till the destination party answers. Instead of Music on Hold, Ringback Tone can be sent to the caller while he or she is being transferred (See Section 10-C-53.00 “World Select 3 (WS3)“). Oparation -2 (Mode 2) While having a conversation; 1. Press the switchhook for approximateiy one half sec’ond and release it. l The other party is put on Consultation Hold. + You hear confirmation tone 2 and then dial tone 1 or 3 or 4. 2 . Dial the feature number for Transfer “%“(Default). 3 . Make a call to an Attendant Console. l You hear ringback tone. l Calling an Attendant Console starts. 4 . Replace the handset. l At an Attendant Console: The call is displayed as a transfer recall. Note: The feature numbers and DN’s for making a call to an Attendant Console are: l l Operation -1 (Mode 1) l While having a conversation; l 5-D-3-l (70695) Operator Call (General) Operator Call (Specific) FDN for General Operator Call DN for ATT1 and AlT2 1.05 Unscreened Call Transfer -to a UCD Group (with OGM) Description Operation -2 (Mode 2) Allows an extension user to transfer an outside call to a UCD Group from 01 to 04 (with OGM type). While having a conversation; . 1. Press the switchhook for approximately one half second and release it. l The other party is put on Consultation Hold. l You hear confirmation tone 2 and then dial tone 1 or 3 or 4. From version 8.Xx, not only the operators but any extension user can transfer an outside call to a UCD group (with OGM). Programming 2. Dial the feature number for Transfer “58”(Default). l You hear confirmation tone 2 and then dial tone. 1 Conditions If all group members are not available to answer the call, it will be redirected to the Overflow destination. In this case, the call will be disconnected if not answered by the Overflow .destination within 60 seconds. See page 3-D-l 3 for further information. 14% I 3. Dial the FDN for UCD group (01 to 04). l You hear confirmation tone 3 and then dial tone 1 or 3 or 4 4. Replace the handset. Operation -1 (Mode 1) Feature References While having a conversation: Uniform Call Distribution OGM (Section 3-D-2.06) 1 Press the switchhook for approximately one half second and release it. l The other party is put on Consultation Hold. l You hear confirmation tone 2 and then dial tone 1 or 3 or 4. 2 Dial the FDN for UCD group (01 to 04). l You hear confirmation tone 3 and then dial tone 1 or 3 or 4. 3 Replace the handset. 5-D-3-2 (70695) (UCD)-with/without 1.06 Screened Call Transfer to Trunk Description Operation (Mode 2) Allows an extension user to transfer calls (both extension and outside) to an outside party with announcement. Available when “SLT Transfer Operation” is set to “Mode 2”. While having a conversation; 1. Press the switchhook for approximately one half second and release it. To execute this function, assign ‘System-Class of Service”, CO Transfer mode to “Yes.” l l If outside call is transferred to another outside party, CO-CO conversation mode is established and the duration of the conversation is restricted by “Group-Trunk Group”, CO-CO Duration Limit. 2. Dial the feature number for Transfer “58” (Default). I Programming System Programming “System-Class of Service (l/2)“, CO Transfer Mode “System-Numbering Plan (1 l/71 )“, Transfer I%roup-Trunk Group (l/2)“, CO-CO Duration Limit “World Select 3 (WS3)” SLT Transfer Operation The other party is placed on Consultation Hold. You hear confirmation tone 2 and then dial tone 1 or 3 or 4. Rek In- * You hear confirmation tone 2 and then dial tone. 3, Call another outside party 4D-4.01 l 9-D-6.11 You hear ringback the CO line. tone from _ g-E-1 .Ol - 4. When the destination answers, make the announcement. Conditions la If a call from outside party is transferred to another outside party, CO-CO conversation mode is established. In this case, the system uses the preset time limit for the trunk group that the transferred party is placed on,.not using the time limit for the trunk group used to call the destination and alarm tone is sent to parties 15 seconds before the assigned time limit, and when time is out, both CO lines are disconnected. l l The call is transferred to the destination. Note: *If an extension that cannot execute this function (by COS restriction) attempts to do this procedure, the system sends a consultation hold recall to the extension after step 5 and the transfer is rejected. The extension users can not transfer the following calls. l 5. Replace the handset. *If you want to return to the held party, press the switchhook for approximately one half second and release it before the destination answers. A call with Attendant Console A call with Doorphone If Music on Hold is available, from the start of the transferring operation until the destination party answers, the system sends Music on Hold to the transferred party. For further detail, refer to Section 3-E-l .OO “Music on Hold.” l 5-D-3-3 (70695) If CPC signal is not supplied by the Central Office in your area, KX-T336 cannot detect the end of CO-CO call after one party disconnects the call. In this case, we recommend to use tone detection feature of AGC Card (See Section 1 O-C-67.00 ‘DISAIAGC Tone Detection Mode (TOM)“). 2.00 Call Forwarding (FWD) 2.01 Call Forwarding-All Calls Description Conditions Call Forwarding-All Calls allows extension users who are away from their phones to receive incoming calls (both extension and CO) to them at another extension. An extension user may have only one type of Call Forwarding/Do Not Disturb feature in effect at any time. If a second type is assigned, the previously assigned type is canceled. Incoming calls can be forwarded either to extension users, Voice Mail port, or operators (Attendant Console or Extension). “FDN for General Operator Call” can be used to assign operators as the destination of Call Forwarding. Refer to Section 9-D-l .Ol “Operation (l/3)” for further information. If the extension to which calls are to be forwarded itself is in a call forward mode, a call is not forwarded furthermore. The call rings at the first forwarded extension. In case of an outside call, if not answered in a specified time period, the call will be routed to another destination, if available, based on the “Intercept Routing-No Answer” feature. The following incoming calls do not receive Call Forwarding treatment. If Tenant Service is employed and “Inter Tenant Calling” is assigned to “Yes” by programming, this function is ineffective for the calls from another tenant if the destination of Call Forwarding-All Calls is set to an Attendant Console. l A call from doorphone -0 A call routed via DIL 1: N feature l A call directed to a UCD group To execute Call Forwarding-All Calls, assign “System-Class of Service”, Call’Forwarding/Do Not DistuW to Yes.” To set and cancel this function, dial the feature number for “Call Forwarding-Ail Calls Ser and “Call Forwarding-Do Not Disturb Cancel.” Calls from any VM extension will not be forwarded, if forwarding destination is another VM extension. The following attempt will be rejected with reorder tone. l Programming System Programming - Reference VT Dumb l ‘System-Class of Service (l/Z)“, 9-D-4.01 10-C-7.00 Call Forwarding/Do Not Disturb “System-Numbering Plan (04/l 1r. Call Forwarding-All Call Set Q-D-6.04 10-0-10.00 “System-Numbering Plan 9-D-6.05 1 O-c-l 0.00 (05/l 1)“, Call Forwarding/Do Not If Tenant Service is employed, the user cannot set the destination to an extension in the other tenant. To call the other extension whose call forwarding destination is set to his or her own extension. The Operators (Attendant Console or Extension) can cancel the Call Forwarding/Do Not Disturb feature assigned to the extension users. Refer to Section 5-G-9.00 ‘Remote Station Feature Control.” Disturb Cancel 5-D-4 (70695) - Operation Setting Call Fonvarding-Busy/Off-Hook/No Answer 1. Lift the handset. Canceling Answer Call Forwarding-Busy/Off-HooWNo 1. Lift the handset. 2 . Dial the feature number for “Call Forwarding-Busy/No Answer.” 2. Dial the feature number for “Call Forwarding/Do Not Disturb Cancel.” 3 . Dial the directory number of the extension or the Voice Mail port, or the ‘FDN for General Operator Call” to be set as the destination. l l You hear confirmation tone 1 or 2 and then dial tone 1 or 3 or 4. 3. Replace the handset. You hear confirmation tone 1 or 2 and then dial tone 1 or 3 or 4. 4 . Replace the handset. . 5-D-15 (21292) 2.05 Call Forwarding to Trunk Description Conditions Call Forwarding to Trunk allows extension users who are away from their phones to receive incoming calls (both CO and extension) at outside place. An extension user may have only one type of Call Forwarding/Do Not Disturb feature in effect at any time. If a second type is assigned, the previously assigned type is canceled. When an incoming CO call is forwarded to the pre-assigned outside party by this feature, CO to CO call via this system is established. Duration time.of CO to CO call is restricted by “GroupTrunk Group,” CO-CO Duration Limit of receiving CO line. The system sends alarm tone to both parties 15 seconds before the Duration Limit time is expired, and when expired the system disconnects both parties compulsively. The Operators (Attendant Console or Extension) can cancel the Call Forwarding/Do Not Disturb feature assigned to the extension users. Refer to Section 5-G-9.00 “Remote Station Feature Control.” The following incoming calls do not receive Call Forwarding treatment. l l l Up to 32 digits composed of “0 through 9” and “jc” can be entered as the telephone number of the destination. CO line access code must be entered as the leading digit of each entry. Note: If CPC signal is not supplied by the Central Office in your area, KX-T336 cannot detect the end of CO-CO call after one party disconnets the call. In this case, we recommend to use tone detection feature of AGC Card (See Section 1 OC-67.00 ‘DISAIAGC Tone Detection Mode CTW”). l A call from doorphone A call routed via DIL 1: N feature A call directed to a UCD group To set Call Forwarding to Trunk, assign both “System-Class of Senrice”, Call Forwarding/Do Not Disturb and CO Forward Mode to Yes.” To set and cancel this function, dial the feature number for “Call Forwarding-To Trunk’ and “Call Forwarding/Do Not Disturb Cancel.” Programming System Programming Reference VT I Dumb ‘System-Class of Service (l/2)“, Q-D-4.01 Call Forwarding/Do Not Disturb CO Forward Mode “System-Numbering Plan (04/11)“, Call Forwarding-to Trunk “System-Numbehg Plan (OS/U)“, Call Forwarding/Do Not Disturb Cancel “Group-Trunk Group (l/2)“, CO-CO Duration Limit lo-c-7.00 9-D-6.04 lo-c-10.00 Q-D-6.05 lo-c-10.00 9-E-1 .Ol 10-c-14.00 6-D-16 (70695) 2.05 Call Forwarding-Follow Me Canceling “Call Forwarding-Follow Me” at the destination extension. Description 1. Lift the handset. You can set a ‘Call Forwarding” feature from the destination extension. This is useful if you forget to set “Call Forwarding -All Calls” before you leave your desk or when you move from pre-set place to another. This feature can be enabled or disabled on a COS (Class of Service) basis. If enabled, an extension user can set this feature. 2. Dial the feature number for Call Forwarding-Follow Me Cancel ” * * 8” (default). You hear confirmation tone 1 or 2 and then dial tone 1 or 3 or 4. l Programming System Programming Reference VT 3. Dial the directory number of your extension. 1 Dumb “System-Numbering plan (09/l 1)“. Call Forwarding-Follow Me Set Call Forwarding-Follow Me Cancel %all Fomarding-Follow Me (CFM) Conditions Same as ‘Call Forwarding-All Calls “(Section 5 D-2.01). l 4. Replace the handset. Note: You can cancel this feature at your own extension by following the same procedure as canceling other forwarding features. Operation Setting “Call Forwarding-Follow Me” at the destination extension 1. Lift the handset. 2. Dial the feature number for Call Forwarding-Follow Me Set “* * 7” (default). 3. Dial the directory number of your extension. l You hear confirmation tone 1 or 2 and then dial tone 1 or 3 or 4. You hear confirmation tone 1 or 2 and then dial tone 1 or 3 or 4. 4. Replace the handset. 5-D-19 (70695) - E. Conversation Features 1 .OO Conference Description Operation Allows an extension user to add a third-party to a two-party conversation and make a three-party conference. An extension user can have the following combination of calls on the line: Establishing a conference - 1 (Default mode) (SLT Transfer Operation is in Mode 1) l l l While having a two-party conversation; 1. Press the switchhook for approximately one half second and release it. three extensions one extension and two outside parties two extensions and one outside party l On the TSW card, there are eight standard conference trunks provided for this purpose. By equipping the optional conference expansion card (KX-T336104), the number of conference trunks increases to 64. To utilize optional conference expansion card, assign ‘Configuration-System Assignment”, TSW Additional CONF to ‘Yes.” l 2. Dial the phone number of the third party. 3. Press the switchhook for approximately one half secondand release after the third party answers. When two members in the conference are both outside parties, two conference trunks are necessary. In all other cases, one conference trunk is enough. l Programming l Reference System Programming “Configuration-System Assignmenr. TSW Additional CONF “System-Numbering Plan (1 l/l 1)” Conference World Select 3 (WS) SLT Transfer Operation VT 1 Dumb .OO 1 o-c-1 .oo 9-C-l 9 - D - 6 . 1 1 1 o-c-1 0.00 I The other party is placed on Consultation Hold. You hear confirmation tone 2 and then dial tone 1 or 3 or 4. You hear confirmation tone 3. . A three-party conference is now established. Establishing a conference - 2 (SLT Transfer Operation is in Mode 2) While having a two-party conversation; 1. Press the switchhook for approximately one half second and release it. 10-c-53.00 I Conditions l Pressing the switchhook by the conference originator during the conference restores a conversation with the first party. This places the second party on Consultation Hold. l The other party is placed on Consultation Hold. You hear confirmation tone 2 and then a dial tone 1 or 3 or 4. 2. Dial the feature number for conference “58” (default). Pressing the switchhook again establishes the conference again if the conference trunk is available. If the conference trunk is not available, conversation with the held (second) party starts, placing the first party on Consultation Hold. l You hear confirmation tone 1 and then a dial tone. 3. Dial the phone number of the third party. 5-E-l (70695) 4. Press the switchhook for approximately one half second and release it after the third party answers. l l You hear confirmation tone 3. A three-party conference is now established. Note: If the conference trunk is not available in step 3, . you cannot establish conference by pressing the switchhook, which puts the third party on Consultation Hold, and conversation with the held party starts. Concluding a conference 1. Replace the handset. . The other two parties may continue their conversation. . If the other two parties are both outside parties, they will be disconnected. Talking to the original party while holding the third party I 1. Press the switchhook for approximately one half second and release it. l l You hear confirmation tone. You can talk to the original party. 5-E-l -1 (70695) 2.00 Doorphone Description Operation Up to four doorphones can be connected to the system. This provides conversations between extensions and doorphones. Calling from a doorphone Any extension user can call the doorphones within the same tenant by dialing the feature number for ‘Door-phone Call (1 to 4).” It is possible to direct calls from doorphones to specified extensions, intercom groups, pickup groups or Attendant Consoles in “ExtensionDoorphone”, Doorphone Call Assignment. 1. Press the button on the doorphone. l l Answering a doorphone call When your telephone set receives a doorphone call and rings, If Tenant Service is employed, the affiliation of each doorphone can be determined by the system programming in “Extension- Doorphone”, Tenant. Set the duration of the door opener in “ExtensionDoorphone”, Open Duration. When Open Duration is set to ‘0,” the door opener is unavailable. You hear ping-pong tone. When the other party answers, start conversation. 1. Lift the handset. l Start conversation with the caller from the doorphone. Calling a doorphone 1. Lii the handset. Programming I System Programming 2 . After dialing the feature number for Doorphone Call (1 to 4) u40” (default), dial the doorphone number : 1 to 4. w l Conditions Only conversations are available for the door-phone. The other functions such as Hold, Transfer are all ineffective. When a visitor presses the button on the doorphone, he hears ping-pong tone twice, then doorphone call ringing starts at the designated extension. No answer of the call in 15 seconds cancels the doorphone call. After hearing confirmation tone 3, start conversation over the specified doorphone. 3 . After concluding conversation, replace the handset. Opening the door During a conversation over the doorphone I?77 1. Press the switchhook for approximately one half second and release it. 2. Dial “5.” I 5-E-2 (70695) J l The door opens for the specified duration. 3.00 Returning to Previous Screen To return to the previous screen, press the PF2 key. The illustration below shows the operation, staring from the Setting Screen and returning to the Main Menu screen. Pressing the PF2 key returns the screen to the Sub Menu screen. I PF2 n Pressing the PF2 key returns the screen to the Programming Main Pressing the PF2 key returns the screen to the Main Menu screen. Main Menu screen is displayed causes no change of the screen and error entry tone sounds. 7-c-3 4.00 Programming Main Menu Type “1” and press the RETURN key in the Main Menu screen then the Programming Main Menu is displayed on the screen, + System Programming Main Menu Group The illustration below shows the submenu screens and the setting screens of Programming Mainmenu. Operation Tenant System Timer Class of Service Local Access Numbering Plan Communication Interface Speed Dialing-System Absent Messaae Trunk Group ICM/Paging Group I Call Pickup Group Pager & Music Source Attendant Console 7/l 0 Digit Toll Restriction Table ‘=TgF ‘-7 ;gine Routing Tab,e Installation Information I Power Failure Transfer Configuration Assigns the data concerning cards, slots, T-l channels and DNs (directory numbers). For further details, refer to Section 9-C “Configuration Screen.” Miscellaneous Assigns the installation information and cards for effectuating Power Failure Transfer. Refer to Section 9-L “Miscellaneous Screen.” System Assigns the elemental data common to the whole system. For further details, refer to Section 9-O ‘System Screen.” Group Assigns the data for trunk groups, ICM paging groups and pickup groups. For further details, refer to Section 9-E “Group Screen.” Trunk Assigns various parameters for CO lines, external pagers and music sources or tenant number for AGC (Automatic Gain Control). Refer to Section 9-F Trunk Screen.” Extension Assigns the parameters for each extension, DSS consoles, Doorphones and Attendant consoles. Refer to Section 9-G “Extension Screen.” Special Carrier Access Assigns available trunk groups and parameters necessary for making Equal Access or OCC (Other Common Carrier) Access calls. Refer to Section 9-H Special Carrier Access Screen.” Toll Restriction Assigns parameters for Toll Restrictiin. Refer to Section 9-i roll Restriction Screen.” Automatic Route Selection Assigns the parameters for Automatic Route Selection. Refer to Section 9-J “Automatic Route Selection Screen.” Special Attended Assigns parameters for DISA (Direct Inward System Access), DID (Direct Inward Dialing), UCD (Uniform Call Distribution) and TIE Line Routing Table. Refer to Section 9-K “Special Attended Screen.” 7-c-s (70695)M 5.00 Test Main Menu 6.00 Monitor Main Menu Type “2” and press the RETURN key in the Main Menu screen, then the Test Main Menu is displayed on the screen. This menu consists of three submenus as illustrated below. Type “3” and press the RETURN key in the Main Menu screen, then the Monitor Main Menu is displayed on the screen. The illustration below shows the submenu screen and the setting screens. 1 Monitor Main Menu 1 A Error Log - Device Status Card Test Verifies the card conditions and enables you to detect whether troubles are caused by a card or telephone instruments. 1 Traffic P o r t T e s t Verifies the port conditions and enables you to detect troubles when telephone instruments don’t function well while card condition is gocd. - Station - Trunk Group - Attendant console rDISA _ - OGMl - OGM2 -AGC . Error Log Displays up to 15 major and minor alarms and up to 15 light alarms. For further details, refer to Section 14-G-2.00 “Error Log screen.” PITS and ATT Test Verifies the conditions of PITS and the Attendant Console (ATT) and enables you to detect troubles when telephone instruments don? function well while card condition is good. Device Status Displays the status of the system, cards, ports and the conference trunk. For further details, refer to Section 14-G-3.00 ‘Device Status screen.” For further details of testing, refer to Section 14-F “Functional Test by Entering Commands.” Traffic Displays traffic measurements of extensions , trunk groups, attendant consoles and resources (DISA, OGMl, OGM2, AGC). For further details, refer to Section 14-G-4.00 ‘Traffic Submenu screen.” 7-C-6 D. Input Format-General 1 .OO Programming Mode Input Format-General In the programming mode (when PRG>fl is displayed on the screen), enter as follows: _ 1 2 3 : PRG>m /Tvoe of Model 1Index Number/ II -. b Item Number [Carriage Return 1 (CR)tll Note: Be sure to enter one space between the items. The ( J ) in the followings indicates pressing the RETURN key. Displaying “Operation (OPR)” command, SMDR (Index number 2, Item number 02) Enter as follows: ;PRG>OPRSH202(-1) . . 1. Commands The following programming commands are available in the programming mode. For further information about programming, refer to Section 10 “System Programming-Dumb Type Terminal.” Programming System Assignment Slot Assignment DN Assignment Channel Assqnment Operation Tenant System Timer Class of Service 1 Class of Service 2 Local Access Group Numbering Plan Communication Interface Speed Dialing-System Absent Message Trunk Group (112) Trunk Group (2/2) lCM/Paging Group Call Pickup Group CO Line External Paging Music Source Command WA SLA DNA :z TNN TIM CSl CS2 LAG NBP COM SPD ABS TGl TG2 IPG CPG COL PAG MUS 1 Auto Gain Control Extension DSS Console DN Button Assignment PF Button Assignment DSS Button Assignment Dootphone Attendant Console Attendant Queue Priority Equal Access OCC Access TRS Area/Office Code Tables TRS Office Code Tables TRS 7/10 - Digit Table ARS Leading Digit Table ARS Office Code Tables ARS Route Plan Tables ARS Route Lists Table ARS Modified Digit Table DISA DISA Code DISA Password DID UCD (l/2) UCD (2I2) TIE Line Routing Table Installation Information Power Failure Transfer Change Password CPC Detect Time-Outgoing World Select 1 World Select 2 Automatic Busy-out Count World Select 3 CO Access Instantly Account Code Verified Account Code Entry on Long Distance Calls Speed Dialing Boundary Night Answer Group Polarity Reversal Detection Voice Mail Directory Number Mail Box Number Waiting for Second Dial Tone Equal Access Code World Select 4 TIE Account Code Clock Mode Clock Priority TIE Trunk Relay Ftestrfction Tone Detection Mode tine Hunting Sequence ESF Frame Option Limited Call Duration Call Forwarding-Follow Me 8-D-l (70695)M AGC EXT DSS DNK PM DSK DPH Al-r AQP EQU occ TRl TR2 TR3 AR1 AR2 AR3 AR4 AR5 DIS DIC DIP DID UC1 UC2 TIE INF E CPC WSl ws2 ABC ws3 CAI ACV ACL SPB NAG PRD VMD MBN WSD EQC WS4 TAC CLK CLF TRR TDM LHS EFO LCD CFM 2.Type of Mode 2) Auto Type-AT Three types of Show type, Auto type and Batch type are available. Enables you to show or edit the data in an interactive format. 1) Show Type-SH Showing the data Each item appears one by one by every pressing of the RETURN key. Enables you only to read the preset data. The preset data cannot be changed by this type. Displaying the data in System Assignment Enter: ; PRG>SYA SH (4 ) ; Editing the data If you do not want to change the data, press the RETURN key when ; INPUT>>0 is displayed. If you want to change the data, enter the appropriate values after ; INPUT=fl, then press the RETURN key. To save the data after changing it, be sure to enter $EOD after ; INPUT>> fl, then press the RETURN key. Changing the data in System Assignment Enter: ; PRG>SYA AT (4 ) I I a Displays: . 1 : Expansion shelf + ; INPUT>>fl N I To change N to Y, enter Y ( 4 ). Next item appears: u * 2 : Additional CONF+ ; INPlJT>>fl Y To save the data of item 1, enter $EOD (4 ): Concludes AT mode a 8-D-2 G. Help Function 1 .OO Programming Mode 2.00 Operation Mode Description Description Used to display brief instructions and a list of commands available in the Programming Mode. Used to display brief instructions and a list of commands available in the Operation Mode. Input Format Input Format ; PRG>pI ; OPE>)q m[ ml * Display (Version 12.Xx) : PFiGh@ : << Cmmand+Type+(!ndex)t(UemNo.) >a ;CdarR SlA . ..%tAssipmnl ; SYA . ..9jsll?m~enl ; DNA . ..ONAsiqmmt CHA . ..&&WV&pTM ; CPR . ..cpMlion TNN . ..Tenanl ; T I M . ..syllemrdnu ‘31 . ..CbssdSehe(Uq ; CS2 . ..ClassdSaNico(Z2) LAG . ..LC&kaaGfOUp NW . ..NumL’kgFbn ax!. ..calmlmiiLd~ Ass . ..AbsefeM~ I SPO . ..~~.sy5lem TGZ . ..TtunkGmq(2Q ; TGl . ..TnmkGmp(l~!Z) : Iffi . ..lcm#gGrwp CPG . ..cailRdplpGmup PAG . ..Eaem~P@g : COL . ..coLine AGC . ..AGC ; Hus . ..Yusicsmm : 5x-r . ..saiM 05s . ..DSSCOlSOk PfK . ..sl-Pl=Kq~ : ONK . ..%alkm0~~mpni ; 0% . ..SWss~~ OF+! . ..ouxphord ; A T T . ..AmdartCmo~ AC@ . ..AnenQlltQeP~ ; Ecu . ..EqJdAal!s ccc . ..ccckas ; TRl . ..TRSh&%eC&Table TR2 . ..TRSO!htiTabh : TR3 . ..TRS7flOD91Tak& AR1 . ..ARsLmirgC@itTablr AF3 . ..ARsRapeFbilT&S ; AR.2 . ..ARSUfbeC&TaMs : AR4 . ..ARsRadeL&sTaMe AR3 . ..ARS~~T* ; 0s . ..osA or: . ..mAccde ; D I P . ..0lsAP2sswd MD . ..oIo : UC1 . ..UCo(llq UC2 . ..ua(2q nE . ..TELiis!UiqT~ INF . ..hbwmCHG . ..ChaqPassaad ; PET . ..PowFailumT~& : WC . ..cFcLMedrkre-~ Wsl . ..WOdd24&1 ; ws2 . ..wc4dsdm2 ABC . ..Manaic~~ CA . ..coka%~ ;m . ..WCddsaledO ; KY . ..kmudcodavarired Aa . ..kaNdcoaLMgatna ; sm . ..spldcidmuldaq NAG . ..N~caWQWp : PRU . ..PhityRawc&ta& wo . ..vomyJDN : YBN . ..MaiBorNurkr WSD . ..Wa&g%mndWTan ; Em . ..EqdAJmscadl ws . ..Wa(dSd@l alt . ..cbcklbde ; TPC . ..TlEAcmwcad. TRR . ..TETIIP*f4@R ; CLP . ..Clc4k~ Lls . ..LklewurdngseQJena ; TOY . ..TanOC4hCtuoS( ; EFO . ..ESFFramnO#m LCO . ..Li?MC1Rmtipa ; cw . ..wFobue : Typm.. : SH...shcrrTypa AT...wOkba%tT~ K...&hsclTm ;PKb 8-G-l (70695)M Display ;OPE>HLP > ;Gmunand are.. SYM . ..System Mainteme Monitor ; TST .-Test : I N S . ..lnSerke OUS -Out of Sefviie ; R E M .,Remove ERR -DisplayError Log ; T F D -TM% Display PRT -Print Cut LOO -Program Data Load : SOT -Set Date and Tiie ; SAV -Program Data Save CHL -Change Level ;SHL...ShWLeVel R S T -Restaft : D T M .,DTMF-QRDiagnosfs LET .-LoopBadcTest : V U P w.ROMversimup ERT -EmRate ;DPG Section 9 System Programming VT220 and Compatibles (Section 9) System Programming VT220 and Compatibles Contents A Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 9-A-l B Construction of Programming Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-B-l C Configuration Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-C-l 1.00 2.00 3.00 4.00 System Assignment ........................................................ Slot Assignment .............................................................. DN Assignment ............................................................... Channel Assignment ....................................................... 4.01 T-l card .................................................................. D System Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 .oo 2100 3.00 4.00 5.00 6.00 7.00 8.00 9.00 9-D-l Operation ........................................................................ 1 .Ol Operation (l/3) ................................................. ...... 1.02 Operation (2/3) ....................................................... 1.03 Operation (3/3) ........................... . ........................... Tenant.. ........................................................................... System Timer .................................................................. Class o f Service .............................................................. 4.01 Class of Service (l/2) ............................................. 4.02 Class of Service (2/2) ............................................. Local Access Group ........................................................ Numbering Plan .............................................................. 6.01 Numbering Plan (01/l 1 ) ......................................... 6.02 Numbering Plan (02/l 1) ......................................... 6.03 Numbering Plan (03/l 1) ......................................... 6.64 Numbering Plan (04/l 1) ......................................... 6.05 Numbering Plan (05/l 1) ......................................... 6.06 Numbering Plan (06/l 1) ......................................... 6.07 Numbering Plan (07/l 1 ) ......................................... 6.08 Numbering Plan (080 1) ......................................... 6.09 Numbering Plan (09/l 1 ) ......................................... 6.10 Numbering Plan (1 O/l 1) ......................................... 6.11 Numbering Plan (1 l/l 1) ......................................... Communication Interface ................................................ Speed Dialing-System.. ................................................... Absent Message ............................................................. E Group Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..-...... 1 .OO Trunk Group .................................................................... 1 .Ol Trunk Group (l/2) .................................................. (70:;5)M 9-C-l 9-C-3 9-C-6 9-C-8 9-C-8 9-D-l 9-D-l 9-D-7 9-D-l 1 9-D-14 9-D-18 9-D-22 9-D-22 9-D-27 9-D-31 9-D-33 9-D-33 9-D-36 9-D-40 9-D-44 9-D-48 9-D-52 9-D-56 9-D-59 9-D-63 9-D-64-2 9-D-64-3 9-D-65 9-D-68 9-D-70 9-E-l 9-E-l 9-E-l 2.00 3.00 1.02 Trunk Group (2/2) .................................................. KM/Paging Group .......................................................... Call Pickup Group ........................................................... F Trunk Screen ............................................................................... 1.00 C O Line.. ......................................................................... 2.00 Pager and Music Source ................................................. 3.00 AGC ............. .................................................................. G Extension Screen ........................................................................ Station ............................................................................. 1 .Ol Station (l/3) ........................................................... 1.02 Station (2/3) ........................................................... 1.03 Station (3/3) ........................................................... 2.00 DSS Console ............. I .................................................... 2.01 ‘DSS Console (l/3) ................................................. 2.02 DSS Console (2/3) ................................................. 2.03 DSS Console (3/3) ....................... . ......................... 3.00 Doorphone ...................................................................... 4.00 Attendant Console .......................................................... 4.01 Attendant Console (l/2) ......................................... 4.92 Attendant Console (2/2) ......................................... 1 .oo Page 9-E-9 9-E-l 2 9-E-l 4 9-F-l 9-F-i 9-F-5 9-F-8 9-G-l 9-G-l 9-G-l 9-G-7 9-G-l 2 9-G-l 5 9-G-l 5 9-G-l 3 9-G-21 9-G-24 9-G-27 9-G-27 9-G-30 H Special Carrier Access Screen .................................................... 1 . O O Equal Access .................................................................. 2.00 OCC Access ................................................................... 9-H-l 9-H-l 9-H-5 I Toll Restriction Screen ................................................................ 1 .OO Area/Office Code Tables ................................................. 2.00 Offfce Code Tables ......................................................... 3.00 7/l 0 Digit Toll Restriction Table ...................................... 9-l-l 9-l-l 9-l-4 9-l-6 J Automatic Route Selection Screen .............................................. 1 .OO Leading Digit Table ......................................................... 2.00 Office Code Tables ......................................................... 3.00 Route Plan Tables .......................................................... 4.00 Route Lists Table ............................................................ 5.00 Modified Digit Table ........................................................ 9-J-l 9-J-i 9-J-3 9-J-6 9-J-9 9-J-13 K Special Attended Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.00 DlSA ............................................................................... 2.00 DID ............................................................................... 3.00 UC0 ............................................................................... 3.01 UC0 (l/2) ............................................................... 3.02 UC0 (2/2) ............................................................... 4.00 TIE Line Routing Table ................................................... L Miscellaneous Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Error Message Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-K-l 9-K-5 9-K-7 9-K-7 9-K-9 9-K-l 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..-.. 9-L-l 1 .OO Installation Information .................................................... 2.00 Power Failure Transfer Assignment ................................ M Page 9-K-l .............................. Error Messages Related to the Assigning Items in the Same Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.00 Error Messages Related to the Assigning Items in the Other Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.00 Other Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-L-l 9-L-3 9-M-l 1 .OO 9-M-l 9-M-2 9-M-7 A. Introduction This section provides system programming using VT compatible terminals. Before starting system programming, Section 7 “Preparation for Programming and Maintenance (VT220 and Compatibles)” must be read. This section provides the basic operations required for system programming. Programming consists of 10 submenu screens and each submenu consists of various setting screens. The setting screens are used to assign or change various parameters concerning the system administration such as Tenant, Class of Service, Numbering Plan and so on. The setting screens should be programmed in order of “First Set,” “Second Ser and “Third Set” which is illustrated in “Construction of Programming Mode” on the following page. If you program a screen in the second set before setting the first-set screens, an error message will appear. For example, if you program “Extension” before programming “ConfigurationDN Assignment,” an error message is displayed. In this section, each setting screen is explained using a screen and an explanation table. 9-A-l B. Construction of Programming Mode Password LFvel + 1 I 1 Programming I1 System Assignment -- 2 Slot Assignment 1 t First Set 1 - 3 DN Assignment - 4 Channel Assignment 1 1 -----e-m .------------------------T 02 System I - I I I I Second Set I I I I I - - -.L - - - - -j 03 Group Operation Tenant System Timer Class of Service Local Access Group Numbering Plan Communication interface Speed Dialing-System Absent Message (-.,-I 1 Trunk Group H 2 tCM/Paaina Grout q 3 Call Pickup Grouo 2 2 2 2 2 2 2 3 3 21 21 21 .---------------------w--m T I I . 1 2 3 4 5 6 7 8 9 I I I I I I I 1 CO Line - 2 Pager & Music Source - 3 AGC 3 3 3 l Station - 2 DSS Console - 3 Doorphone - 4 Attendant Console 3 3 3 2 1 Equal Access 2 OCC Access 2 2 Third Set I I I 1 Area/Office Code Tables - 2 Office Code Tables - 3 7/10 Digit Toll Restriction Table 2 2 2 1 - 2 n 3 4 2 2 2 2 I I 1 I I I I I I I I 9-B-l (70695)M DISA DID UCD TIE Line Routing Table - Description of Assigning Items Expansion Shelf TSW Additional CONF Enables the expansion shelf 1 when set to “1 Shelf and both expansion shelves 1 and ‘2 when set to “2 Shelves.” Enables the expansion of conference trunks when set to Yes.” Conditions None Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in this setting screen. For operation, refer to Section 7-l uOperation of Function Keys.“ 9-c-2 2.00 Slot Assignment I OFL I PRG I SCR I SEL ---------~-~-~~-~~~~~~~~-~~~~~~~~~~-~~~~~~-~-~~~~~-~~~-~-~~+---+--~-+--Ionfiwration - Slot Assignment ,-------a -------- - - - * ’ ---e ----.---- - -------- l - - - - - L - e - e - - - - - - m e - - - + i Basic I FSOl I T-l I E&nsion I FSOl I PLC IExpansion I FSOl 1 HLC 1 I Shelf I FSO2 I I Shelf 1 I FS02 I PLC I Shelf 2 I FS02 I HLC 1 IFS03 I - I I FS03 I PLC I I FS03 I HLC 1 I I FSo4 I PLC I I FSO4 I PLC I I FS04 1HLC I I 1 FS05 1 T-l 1 I FS05 I PLC I I FS05 I HLC I I IFS06 I - I I FSO6 I PLC I I FE06 I HLC I I I I I I I I I FSO7 I - l I FSO8 I PLC I ; ;;; ; T-l I IFSllI t I FS12 I Plc I I BSOl I CPU I I BS02 I OHCA I I BSo3 I TSV I I FSO? I PLC I I FS08 I PLC I I FS09 I PLC I I FSlO l PLC I I FSll I Pu: 1 I FS12 I SLC I I FS13 I LCOI 1 I FS14 I LCOT I I FSlS I Lcol I I FS07 I HLC I I FSO8 I HLC I I FS09 I DISA I I FSlO I DISA I I FSll I DISA l I Fs12 I DISA I I FS13 I ATLC I I FS14 I DPH l I FS15 I RHT I + - - - - - - - - - - - - ----w-+ --e-e-- - - - - - - - - - - + ------ - ---em -e--4 FS: Free Slot, BS: Basic Slot Summary Assigns the type of servicecards, inserted in the free slots in the basic and expansion shelves. Assigning Items Basic Shelf FS (Free Slot) (01 to 12) (Password level : One) Selection of Value Default Automatic set Blank : Not assigned PLC : Proprietary Integrated Telephone System Line Circuit card HLC : Hybrid Line Circuit card SLC : Single Line Telephone Circuit card MSLC : SLC card with Message Waiting LCOT : Loop Start Central Office Trunk card GCOT : Ground Start CentralOffice Trunk card DID : Direct Inward Dialing card : T-l DIGITAL TRUNK CARD T-l AGC : Automatic Gain Control card DISA : Direct Inward System Access card OPX : Off Premise Extension card ATLC : Attendant Console Line Circuit card DPH : Door Phone Circuit card RMT : Remote Circuit card qeferencs 1 -A-5.00 1 -E-l .OO to2.00 1-E-7.00 to 23.00 Continued 9-c-3 (70695)M Continued Assigning Items Selection of Value Default Basic Shelf BS (Basic Slot) (02) Automatic set Blank : Not assigned OHCA : T-SW Off-Hook Call Announcement card Expansion Shelf 1 FS (01 to 15) Automatic set Same as Basic Shelf FS Expansion Shelf 2 FS (01 to 15) Automatic set Reference i 1 -A-5.00 l-E-1 .co to 2.00 1 -E-7.00 to 23.00 Same as Basic Shelf FS Description of Assigning items Basic Shelf FS (01 to 12) Defines the type of card installed in the free slots (01 to 12) of the basic shelf. Basic Shelf BS (02) Used to utilize the T-SW OHCA card or not. Expansion Shelf 1 FS (01 to 15) Defines the type of card installed in the free slots (01 to 15) of the expansion shelf 1. Expansion Shelf 2 FS (01 to 15) Defines the type of card installed in the free slots (01 to 15) of the expansion shelf 2. Conditions The cursor does not move to BSOl and BS03. In BS02, assignable value is OHCA or Blank. T-l card should be assigned to FSOl ,05 or 09 of any shelf. One T-l card occupies three slots. If you assign a T-l card to FSOl , FS02 and FS03 are not available for other cards. A ‘- (hyphen)’ is displayed in these two slots and the cursor skips them. If no CO trunk card is assigned, “Trunk-CO Line” screen cannot be selected. If no Extension card is assigned, “Extension-Station” screen cannot be selected. If AGC card is not assigned, “Trunk-AGC” screen cannot be selected. If DPH card is not assigned, ‘Extension-Doorphone” screen cannot be selected. If ATLC card is not assigned, ‘Extension-Attendant Console” screen cannot be selected. If DISA card is not assigned, ‘Special Attended-DISA” screen cannot be selected. If DID card is not assigned, ‘Special Attended-DID” screen cannot be selected. When assigning a card, the card status is Out of Service (OUS). When utilizing the card, the card status should be set to In Service (INS). For In Service (INS) and Out of Service (OUS), refer to Section 7-J-4.00 “INS (In Service)” and Section 7J-5.00 “OUS (Out of Service).” For confirming whether the card status is INS or OUS, refer to Section 14-G-3.02 I%ard Status screen.” When deleting (selecting blank) or changing the pre-assigned card type, the conditions should be the followings: l All of the port data has been deleted. l The card status is OUS or Fault. 9-c-4 (70695)M However, if there exist port data, it is possible to change the cards as follows: l PLC card M HLC card l SLCcard * HLCcard Deleting the ATLC card will be an error if there is one of the following assignments: l l “Group-Trunk Group”, Incoming Mode (Day) is set to “ATT.” Intercept Routing (Day) is set to “ATT.” “Extension-Doorphone”, Doorphone Call Assignment is set to “ATT.” Deleting the DISA card will be an error if there is one of the following assignments: l “Group-Trunk Group”, Incoming Mode (Day) is set to ‘DISA.” Incoming Mode (Night) is set to “DISA.” Deleting the HLC, SLC, LCOT or GCOT card will be an error if there is the following assignment to the slot to be deleted: l Miscellaneous-Power Failure Transfer Assignment. See Section 1 -A-5.00 “Service Cards Description” for installing the cards in combination. Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in this setting screen. For operation, refer to Section 7-l “Operation of Function Keys.” 9-c-s (70695) 4.00 Channel Assignment 4.01 T-l card Configuration - Channe Assignment I OFL I PRG I SEL .-----------------------------------------------------------------------+------+------+----Channel Assignmetn ( l/2) + --------------------------------------------+.--------------------------------------------+ I Slot 101 I Option I 1:DTMF 2:DTMF I Slot 105 I Option I 1: DTMF 2:DTMF I 1------------------_-_____I__________ - -_--- 1.-_-----------------------------------I----1 I FrameSequence I D4 I Frame Sequence I ESF I I,_________-----_____------------------------1 I __----------------__-----------------------I I Line Coding I AMI I Line Coding I Ems II - _____--------------- 101 I LCOT WI LCO IO21 GCOT 1101 GCO I03lDID Ill1 DID 1041 DID ll2l DID IOSITIE 1131 TIE 106lTIE l14lTIE 1071 OPX 1151 OPX I08 I OPX 1161 OPX ----------- 1171 LCO 1181 GCO 1191 DID l2Ol DID all TIE l22l TIE r23l OPX t ,I______________________ .------v---e. I24 I264 1271 1281 I291 - 1301 - 1311 - ml OPX 1321 - 1011 L C O 1021 GCO 1031 LCO 1041 G C O 1091 D I D IlOI TIE 1111 TIE 1121 TIE iin Leo El1181 OPX l26l1191 LCO 1271 1201 GCO 128l- 1051 GCO 1131 TIE 1211 OPX 1061 DID 1141 OPX 1221 OPX 1071 DID 1151 O P X I231 LCO 1081 DID 1161 OPX 1241 GCO +--------------I------------------------*.------------------I-------I I I I I I I I I I -m----------I 1291 l3ol1311 1321 - -m-----s+ 01-32 : Channel No. S u m m a r y Assigns the type of T-l interface to each channel. Assigning Items (Password level : One) Default Selection of Value Reference Slot No. Automatic set Physical slot no. (101,105,109,201,205,209,301, 305,309) 3-F-15JXr Frame Sequence ESF 041 ESF 104-64.04 Line Coding B8ZS AMI I 8825 3-F-l 5.00 Channel (01 to 24) Blank: Not assigned LCO / GCO / DID / OPX /TIE Description of Assigning item Frame Sequence Assigns the type of Frame Sequence for each T-l card. Line Coding Assigns the type of Line Coding for each T-l card. Channel (01 to 24) Assigns the type of T-l interface to each channel. Conditions The number of “Channel Assignment screens” may vary depending on the number of Tl DlGlTAL TRUNK cards installed to the system. Up to six Tl DlGlTAL TRUNK cards can be installed to the system. Channel numbers 25 through 32 are not available. A #- (hyphen)” is displayed in these columns and the cursor skips them. If you assign ‘OPX” to a channel, ‘DN Assignment” is also required. Refer to Section 9-C-3.00 “DN Assignmenr. 9-C-8 (70695) D. System Screen 1 .OO Operation 1 .Ol Operation (l/3) ystem - OPerrtton I OFL I PRG I L IN I SEL +---+ W--S------------------------------------------------------+-----+----Operation (l/3) +------------------------------------------------------------------t --------------------I yes I Tenant Service I I Antoautlc Route Selection ---------I No I Noaberlng Plan - - - - - - - - - - - - - - - - - 1 Fixed 1 yes t I Prlvaw on DN Key --------_--------J I Restrlctlon Level - Operator --:---I 01 I I Restrlctlon level - International -I 01 I I Hose Dialing Plan -----------------I Type-A ----------------I rlth Transfer I I DSS Operrt lon Node I BUSY Tone -----------_____--------- 1 Tone-2 I I Held Cat I Resinder -------___- ____ -1 yes I I Beep Tone for Bsy-ovr/Drg-in ------I Yea I I External Pytng 1 , 2 ------------I y&g . yes I External MUSIC Source 1 , 2 -------I Yes , Yes. 1 I Idle Llne Preference --------------I DN I FDN for General Operator Cal I -----I I PBX Code -----___--__-__-----____ 1 951 l I ----------b----------t-------------------------------------------t Summary Assigns elemental data common to the whole system, such as Tenant Service, Automatic Route Selection, etc., through the first SystemAssigning items Selection of Value I Default Tenant Service No No Yes : Tenant Service is unavailable : Tenant Service enabled No Yes No : Automatic Route Selection enabled : Automatic Route Selection is unavailable I Automatic Route Selection Operation screen. This is the first of three screens. (Password level : Two or higher) Reference 3-B-4.00 3-C-2.00 4-C-3.01 5-A-, o, 6-D-l -01 Numbering Plan Fiied 1 3-B-l .OO Flex : feature numbers can be changed Fixed 1: feature numbers are set to Default 1 Fixed 2: feature numbers are set to Default 2 No ~Yes 4-G-1.00 4-G-2.00 4-G-3.00 : barge in allowed (privacy disabled) : barge in disallowed (privacy enabled) ’ 01 to 16 : the restriction level for a telephone company operator call 3-c-1.05 I Continued 9-D-l ( 7 0 6 9 5 ) M I Continued Assigning qestriction items Level-International -lome Dialing Plan Selection of Value Reference 01 to 16 : the restriction level for an international call 3-c-1.05 Default 01 Type-A Type-A : Type-B : Type-C : Type-D : l+NXX+NXX+XXXX NXX+XXXX NPX+NXX+XXXX NNX+XXXX 1 +NPX+NXX+XXXX NNX+XXXX l+ NXX+XXXX 1 +NXX+NXX+XXXX NXX+NXX+XXXX 3-c-1.02 3-Cl.04 3-C-1.06 3-c-1.07 3-C-2.00 AE&mcJ “;““i” Subscriber Number [N : 2 to 9, P : O,l, X : 0 to 91 ISS Operation Mode 3usy Tone : hold .and transfer witi Transfer With Transfer Without Transfer : disconnect and call Tone-2 Tone-l : busy tone 1 Tone-2 : busy tone 2 4-I-12.01 3-B-l 4.0( ield Call Reminder Y e s Yes No : Held Call Reminder is enabled. : Held Call Reminder is not enabled. 3-E-2.00 3eep Tone for Bsy-ovr / Brg-in Yes Yes No : overriding with beep tone : overriding without beep tone 3-B-l 5.0( 4-c-7.00 5-A-5.00 6-D-4.00 : using external pager 1,2 : not using external pager 1,2 2-D-l 80 3-B-8.02 3-D-2.04 4-Da. 00 4-H-l .03 4-H-l -04 4-H-2.00 5-B-2.00 5-F-1.03 5-F-l -04 5-F-2.08 8-l-l .03 8-l-l .04 %ernal Paging 1‘2 Yes, Yes Yes No 6-I-2.00 Continued 9-D-2 (60395)M Assigning Items External Music Source 1,2 Idle Line Preference Selection of Value Default Yes, Yes Yes No : using external music source 1, 2 : not using external music source 1,2 2-D-2.00 3-E-l .OO 4-H-2.00 4-I-4.00 5-F-2.00 6-l-2.00 DN DN : Off-hook selects an idle line by DN : Off-hook selects an idle line by CO 4-c-1.02 12-C-4.M c o FDN for General Operator Call PBX Code Reference blank blank Three or four numeric digits : floating directory number for general operator call 1,2 Up to three numeric digits (O-9) 9-D-3 (70695)M 3-B-3.00 3-D-2.02 3-D-2.03 3-D-2.05 3-D-2.06 4-F-2.00 5-D-2.00 3-F-14.01 Description of Assigning Items Tenant Service Enables or disables the Tenant Service feature. Automatic Route Selection Enables or disables the ARS (Automatic Route Selection) feature. Numbering Plan Selects the type of numbering plan; The user can assign the desired feature numbers or use the default setting 1 or 2. Privacy on DN Key Determines whether or not a PITS telephone user is allowed to barge in on an existing conversation on a PDN, SDN or SC0 button. Restriction Assigns the restriction level for calls to the telephone company operator from an extension. Level-Operator Restriction LevelInternational Assigns the restriction level for international calls from an extension. Home Dialing Plan Selects the home dialing plan. This setting applies to ARS, EQA and occ calls. DSS Operation Mode When With Transfer” is selected, allows the DSS console operator to transfer the CO call to an extension user by simply pressing the associated DN*DSS button on the DSS console. When “Without Transfer” is selected the CO call is disconnected when the DN*DSS button is pressed. Busy Tone Selects busy tone 1 or 2. Busy tone 2 has a unique pattern allowing users with automatic release SLT’s an extended amount of time to enter codes when encountering a busy party. Held Call Reminder When assigned to Yes, the system reminds the user that there is a call on hold. When disabled there is no reminder tone given to the user. In either case the call will be disconnected after 30 minutes if it is not retrieved. Beep Tone for Bsy-ovr/ Brg-in If “Yes” is selected, a beep tone will be heard when executing Busy Override or Barge-in. If ‘No” is selected, there will not be any tone heard when Busy Override or Barge-in is executed. External Paging 1,2 Assigns external pagers 1 and 2 . Idle Line Preference This assignment applies to a PITS telephone when ‘Idle Line PreferenceCalling” is assigned on it. If ‘DN” is selected, an idle DN button is automatically seized by simply going off-hook, and an idle CO button is seized automatically if ‘%O” is selected. FDN for General Operator Call Assigns the FDN (Floating Directory Number) for General Operator Call. This is used for the following attendant-seeking calls: DID, DISA, Call Forwarding and Overflowed UCD calls. There are two entries to allow for two tenants. PBX Code Required when your M-T336 is a part of a TIE Line Network. 9-D-4 (70695)M .- 1.02 Operation (2/3) 1 System - Owration I OPL I PRG I SCR I SEL --------------------------------------------~----+---+----+---. t Operation W3) -~~~~~-------------------------------------I---+ System Administration Device -----I VT220 yes SHDR --------------------I Page Length (4-99) ----------I 60 Skip Perf (O-95) - - - - - - - - - 1 0 I Outgoing Duration Log -------I All Cal 1 I Incoming Duration Los -------I Yes I Attendant Duration ---------I Separate I Special Carrier Name --------I Default I Print Secret Dial -----------I Yes I Error Lcg/Prcmammina/Traffic ---I Yes, Yes, Yes I Start Time of Traffic Measurement -I 12~00 AH I Start Time of Test --I----- 1 1240 fi I Remote Directory Number ------I 1234 I Remote Alarm ------------I yes I Destination Address ---------- I 12346678901234667890123466 +-- - - - - - - - - - - - - - - - - - -----~------~---,----~~+ . / I I t I 1 I I . Summary Assigns elemental data common to the whole system, such as System Administration Device, SMDR (Station Message Detail Recording), parameters for SMDR, etc., through the second System-Operation screen. (Password level : Two or higher) Reference Selection of Value SMDR No VT220 : VT1 OONr220 Terminal Dumb : Dumb Terminal ATT 1 : Attendant Console 1 ATT 2 : Attendant Console ‘2 1 -A-3.00 No 3-F-l .OO 9-O-7.00 Yes Page Length (4 to 99) I I I : not using SMDR (Station Message Detail Recording ) : using SMDR 4 to 99 : page length (number of lines) blank I II 3-F-l .OO Continued 9-D-7 Continued Assigning Items SMDR ( cont.) Skip Perf (0 to 95) Default Selection of Value Reference 3-Fzl .OO blank 0 to 95: how many lines to skip Note : in case of printing out system data : (page length)- (skip perforation)l23 in case of printing out call processing information : (page length)- (skip perforation)l6 in case of printing out error log (page length)- (skip perforation)2_ 4 l Outgoing Duration Log blank : outgoing calls not printed No All Call : print all outgoing calls Toll Only : print outgoing toil calls only (“Toll Only” is not available from software version 9.5X or higher.) 3-F-l .OO Incoming Duration Log blank No Yes 3-F-l .OO Attendant blank Separate Duration : incoming calls not printed : print all incoming calls Summary : charge call duration to Attendant Console : charge call duration to destination 3-F-l .OO Special Carrier Name blank Default : print default name; OC l- 4, EQl- 4 User Name: print user’s name : print dialed number Dial tie. 3-F- 1 .OO Print Secret Dial blank No : not printed Yes : print the secret dial numbers 3-F-l .OO. 4-l-5.00 6-J-3.00 Error Log /Programming/ Traffic blank No : do not print out these items Yes : print each item 3-F-l .OO 7-D 14-D-l a2 14-G 15-D-l .02 Start Time of Traffic Measurement blank 1 to12 : hour 00 to 59 : minute AM/PM : a.m. I p.m. 14-G-4.00 Start Time of Test blank 1 to12 : hour 00 to 59 : minute AM/PM : a.m. I p.m. 14-D-l .Ol 15-D-1.01 Remote Directory Number Remote Alarm Destination Three or four numeric digits: Floating Directory 399 :for Number for the “with RMT” remote mainteblank : for nance port “without RMT= No Address blank No : not providing Remote Alarm Yes : providing Remote Alarm Maximum 26 numeric digits : telephone (modem). number of the destination for Remote Alarm 9-D-8 (70695)M 15-F-2.00 3-B-3.00 4-F-l .05 5-D-l .03 6-G-l .05 14-B-2.00 15-B-2.00 14-D-1.05 15-D- 1.05 Conditions This screen does not appear if ‘System-Operation”, Tenant Service is assigned to “No.” Operator 1 (Tenant 2) Operator 2 (Tenant 2) This system can accommodate up to two Attendant consoles. If two Attendant Consoles are assigned to tenant 1, no Attendant consoles can be assigned to tenant 2. Speed Dialing-System Boundary/Call Park Boundary/Message Waiting Boundary/Absent Message Boundary If Tenant Service is available, the following items can be split between tenant 1 and tenant 2. The boundaries are to set tenant-boundary numbers. The last number that tenant 1 can use must be assigned in each boundary for the functions below: Speed Dialing-System Call Park-System Message Waiting Absent Message Up to 200 speed dialing codes can be programmed for the system. wish to assign 150 codes to tenant 1 and 50 codes to tenant 2, enter ‘150” in Speed Dialing-System Boundary. If you Speed dialing codes ~1 Only tenant 1 can use the codes. Only tenant 2 can use the codes. If tenant 1 uses no code and tenant 2 uses 200 codes, enter ‘000.” Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in this setting screen. For operation, refer to Section 7-l ‘Operation of Function Keys.” 9-D-l 7 _ 3.00 System Timer kstem - System Timer I OFL I PRG I SCR I DIR ----------------------------------------+----+-----+----3---- +---------------------------------------------+ I Held Call Reminder - - - - - - - - - - - - - I @ s e c o n d ( s ) EX!40) I I Held Call Reminder (ATT) ----------I 60 second(s) (E-240) I 1 Transfer Recall -----------------I 30 second(s) 05-240) 1 i Pickup Dial Vaiting ------------I 1 second(s) (l-5) i I External First Digit Time-W ------I 1 0 second(s) ( 5-120) 1 I External Interdigit Time-Out -----I 5 second(s) ( 3- 19 I I External Interdigit Time-Out (PM --I 5 second(s) ( 3- 10) I I Toll Restriction Guard Time-Out ----I 10 second(s) ( C- 25) I I Call Forvarding - Ho Ansver Time-Out I 15 second(s) ( 5- .60) I I Intercept Routing Time-Out (Srstem) -I 60 second(s) ( S-240) I I Intercept Routing Time-Out (DISA) ---I 30 second(s) ( 5-240) I I Attendant Overflov Time ---------I 60 second(s) ( 5-240) I I SHDR Duration Time -----------I 10 second(s) ( O- 15) I 5 second(s) ( 3- 30) I I TIE Interdmt Time-Gut ----------I ~-----------------------------------~ Summary Executes time-setting on various system timers. (Password level : Two or higher) Assigning items Default Selection of Value Reference Held Call Reminder 60 15to240:s 3-B-l 0.00 3-E-2.00 Held Call Reminder (ATT) a0 15to240:s 3-B-lO.OC 3-E-2.00 Transfer 30 15to240:s 3-B-l 0.00 3-E-3.00 4-F-l .Ol 5-D-l .Ol 6-G-l .Ol 6-G-l .02 1 to5 3-B-l 0.00 5-A-2.04 Recall Pickup Dial Waiting 1 :s Continued 9-D-l 8 (70695)M Continued Assigning items Default External First Digit Time-Out 10 5to120 :s 3-B-:1 0.00 3-B-12.00 3-F-12.00 lo-C-58.OC 1 O-C-61 .OC External Interdigit Time-Out 5 3 to15 :s 3-B-10.00 3-B-l 2.00 External interdigit Time-Out (PW 5 3 to10 :s 3-B-l 0.00 3-B-l 2.00 Toll Restriction Guard Timeout 10 oto25 :s 3-B-l 0.00 Call Forwarding-No Answer Timeout 15 5to60 :s 3-6-10.00 3-D-2.05 Intercept Routing Time-Out (System) . 60 5to240 Intercept Routing Time-Out (WA) . 30 5to240 Attendant Overflow Time 60 5to240 Selection of Value Reference 3-D-2.06 4-F-2.03 4-F-2.04 5-D-2.03 5-D-2.04 3-B-l 0.00 3-F-5.00 6-J-l 2.00 :s :s :s 3-B-l 0.00 3-D-2.02 3-F-5.00 3-B-l 0.00 3-D-l .03 6-G-2.00 6-G-7.00 1O-c-53.oc SMDR Duration Time TIE Interdigit Time-Out 5 5 o t o 1 5 :s 3to30 9-D-l 9 (70695)M :s 3-B-10.00 3-F-l .OO 4-A-4.03 3-F-14.00 Description of Assigning Items Held Call Reminder Sets the time for Held Call Reminder for extensions. When this timer expires, the extension is alerted that there is a call held for an exte?ded period of time Held Call Reminder (ATT) Sets the time for Held Call Reminder for the Attendant Console. When this timer expires, the Attendant is alerted that there is a call held for an extended period of time. Transfer Recall Sets the time for Transfer Recall on both extensions and Attendant consoles. Pickup Dial Waiting Sets the waiting time for Pickup Dialing. The waiting time gives the user an opportunity to dial digits prior to the automatic dialing taking place. External First Digit Time-Out Sets the maximum time allowed between CO dial tone or pseudo dial tone and the Time-Out first digit dialed. External Interdigit Time-Out Sets the maximum time allowed between digits on a CO call. This timer does not apply for CO operator calls. External Interdigit Time-Out (PBX) Sets the maximum time between dialed digits (Behind PBX). Toll Restriction Guard Time-Out Sets the time limit between dialing digits for CO operator calls. This prevents a user from attempting to defeat toll restriction. Call Forwarding-No Answer Time Sets the Call Forwarding-No Answer timer. This also functions as -No Answer timer. Intercept Routing Timeout (System) Sets the time limit for Intercept Routing (System). This timer is used when an incoming CO call (DIL l:l, DID, TAFAS or night answer and so on) is not answered. Call forward no answer will override this timer if an extension has enabled Call Forwarding-No Answer Time-Out. Intercept Routing TimeOut (DISA) Sets the time limit for Intercept Routing (DISA). This is used when a DISA destination does not answer. Attendant Overflow Time Sets the overflow time for the Attendant Console. When this timer expires, a call will be routed to the overflow destination. SMDR Duration Time Determines the length of the SMDR duration timer. This timer starts when the system has sent all the digits to the Central Office. TIE Interdigit Time-Out Sets the maximum time allowed between digits on a TIE call after it was received by the system. 9-D-20 (70695)M UCD- 6.00 Numbering Plan 6.01 Numbering Plan (Ol/ll) System - Numbering Plan I Of% I PRG 1 SCR I DIR --------------------------------------------+-----+----+--Numbering Plan (01/U) +----------------------------------------------------~ I No. I Feature I DGl I DG2 I DG3 I DG4 I ----+----------------------~----+--I - f 11 \ 1st Hundred Block Extension------l 1 I I 2 I 2nd Hundred Block Extension------l 2 I I : ; - 1 I 3 I 3rd Hundred Block Extension-------l 3 I 1 : f : ; I 4 I 4th Hundred Block Extension -------I I 5 I 5th Hundred Block Extension ------I 1 I : 1 : ) I 6 I 6th Hundred Block Extension -------I I 1 - 1 - l I 7 I 7th Hundred Block Extension ------I - I - I I 8 I 8th Hundred Block Extension ------I L-l I I 9 I 9th Hundred Block Extension -------I l 10 I 10th Hundred Block Extension ------I I - I - I l 11 l 11th Hundred Block Extension --I--- I I I 12 I 12th Hundred Block Extension ------ I I I : 1 : ; ---+ + ---- --------------------__uIII_u___ 1 COMN 2 IHDEX 3 ij HRD CPY ;i 5 4 i3 J Summary The first screen of the System-Numbering Plan screen sets the extension numbers for the 1 st through 12th Hundred Block Extension groups. Assigning (Password level : Two or higher) Selection of Value Items 1 st Hundred block Extension 1 2nd Hundred Block Extension 2 3rd Hundred Block Extension 3 4th through 12th Hundred Block Extension 0 to 9: set “DGl” and leave ‘DG2” blank when the extension numbers are to be composed of three digits, and set both ‘DGl” and “DG2” when the extension numbers are to be composed of four digits. blank 9-D-33 (70695) Reference *B-~JJO 3-B-2.oo Description of Assigning items 1st through 12th Hundred Block Extension Assigns the leading one or two digits for extension DN (Dire&y Number). If the leading digit is not programmed, the DN assignment is not possible. Conditions “System-Numbering Plan” setting cannot be changed if ‘System-Operation”, Numbering Plan is set to “Fixed 1” or “Fixed 2.” If “Flex” is selected, this setting is changeable. When entedng “DG 1 n to “DG 2,” the cursor does not advance nor return automatically. Use the -+ and c keys to move the cursor. “Parameter Save OK?” will be displayed on this screen, if you attempt to exit this screen without saving the data change you’ve made. Different from other screens, “Parameter Save OK?” is not displayed on this screen when you press the NEXT/PREV key. Data storage is executed by the PF 4 (Memory) key or the PF 2 (End) key for all screens at the same time. Logical check is also performed according to the following logic: Extension numbers and other PBX extension numbers are three or four. digits and the leading one or two digits are assigned in “Numbering Plan” screens. Feature numbers may be one, two, three or four digits. Those numbers assigned in Numbering Plan screens cannot include the same number assigned to other feature number as the part or whole of it. For example, if the digit “2” is assigned to the feature number for Trunk Group 01-08 Access” and another digits “21” is assigned for “Trunk Group 09-l 6 Access,” it is checked at the time of data storage. Similarty, ‘85” and 351” cannot be present at the same time. It is possible to store ‘0” through “9;” “3~ ,” “#,” as the feature numbers. However, if “So or “#” is included in the feature numbers, those features are not accessed by the rotary telephone extensions. 1 st to 12th Hundred Block Extension Extension numbers cannot include ” w ” and “#.” SD-84 (70695) Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are availabie in all setting screens. INDEX key is also available in this screen. The operation of function keys are described in Section 7-l ‘Operation of Function Keys.” Only a message is provided here. INDEX>Numbering Plan (01-l 1)=[1 pJ B H 9-D-35 (70695) H. &xlT @ 6.02 Numbering Plan (02/U) System - Numbering Plan I OFL I PRG I SCR I DIR ----------------__--_______I____________ -+-W-+----+--H+-Hunbering Plan (02111) +------------------------------------------------------~ I Ho. I Feature I DGl I DG2 I DG3 I DG4 I I ---+-------------------------- -+---+---3---+---- I I3 \ 13th Hundred Block Extension-------- I I 14 I 14th Hundred Block Extension------- I t 1 1 / I I5 1 15th Hundred Block Extension------ I I I6 I 16 th Hundred Block Extension---------- I I ! : ; : I 17 I Operator Call (General) ----------I 0 I I I 16 i Operator Call (Specific) ---------I 1 I I I 19 I ARS/Local C O L i n e A c c e s s - - - - - - - - - I 9 I I I 2 0 I T r u n k G r o u p 01-M Access - - - - - - - - - I 8 I 1 1 f I 21 I T r u n k G r o u p 0 9 - 1 6 A c c e s s - - - - - - - - - I 8 I 2 1 I 2 2 I T r u n k Group 1 7 - 2 4 A c c e s s - - - - - - - - - - - I 8 1 3 i 1 I 23 I Speed Dialing - System ---------I * 1 1 I I 24 I S p e e d Dialing - Station --------I * I 2 I I +------~-----------~-----I----~----------+ I 1 ; I I I I I I Summary The second screen of the System-Numbering Plan screen sets the numbers for 13th through 16th Hundred Block Extension groups and functions 17 to 24. Assigning Items Default 14th Hundred Block Extension blank 15th Hundred Block Extension 16th Hundred Block Extension Operator Call (General) 0 Operator Call (Specific) blank CO Line Access Selection of Value ,Fixed 1 1 Fixed 2 13th Hundred Block Extension ARWLocal (Password level : Two or higher) 0 to 9: set ‘DGl” and leave ‘DG2” blank when the extension numbers are to be composed of three digits, and set both ‘DGl” and ‘DGr when the extension numbers are to be composed of four digits.. Enter one through four digits number consisting of 0 through 9, * and # . Reference 3-B-l .OO 3-B-2.00 3-B-l .OO 3-B-5.00 4-c-lO.Oc 5-A-8.00 3-B-l .OO 3-C-2.00 4-C-3.01 5-A-l .Ol 6-D-l .Ol 9 9-D-36 (70695) Continuef Continued Assigning Items Default Fixed 1 1 Fixed 2 Trunk Group 01-08 Access 81 Trunk Group 09-l 6 Access 82 Trunk Group 17-24 Access 83 Speed Dialing-System Speed Dialing-Station Selection of Value Re$rence 3-B-1.00 4-C-3.02 5-A-1.02 6-O-1.02 Enter one through four digits number consisting of 0 through 9, *, and #. 3-B-1.00 4-c-3.03 5-A-1.03 6-D-1.03 *I 6*1 3-B-1.00 5-A-2.02 *2 6*2 3-B-1.00 5-A-2.01 9-D-37 (70695)M Description of Assigning Items 13th through 16th Hundred Block Extension Assigns the leading one or two digits for extension DN (Directory Number). If the leading digit is not programmed the DN assignment is not possible. Operator Call (General) Assigns the feature number for general operator calling. Calls will always arrive at an Attendant Console if it is connected to the system. Operator Call (Specific) Assigns the feature number for specific operator calling. The required.operator is specified by dialing the feature number and for operator 1 and “2” for operator 2. ARWLocal CO Line Access ‘1” Assigns the feature number for Automatic Route Selection or local access. Trunk Group 01-08 Access Assigns the feature number for Individual Trunk Group Dial Access (01 to 08). Trunk Group 09-l 6 Access Assigns the feature number for Individual Trunk Group Dial Access (09 to 16). Trunk Group 17-24 Access Assigns the feature number for the specified EQA or OCC Trunk Group Access. Speed Dialing-System Assigns the feature number for Speed Dialing-System. Speed Dialing-Station Assigns the feature number for Speed Dialing-Station. Conditions Refer to “Numbering Plan (01/l l).” 13th to 16th Hundred Block Extension Extension numbers cannot include y*c” and ‘#.” 9-D-38 (70695) Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in all setting screens. INDEX key is also available in this screen. The operation of function keys are described in Section 7-l “Operation of Function Keys.” Only a message is provided here. INDE>(>Numbering Plan (01-l l)=n H H 9-D-39 (70695) H HEXIT @ 6.03 Numbering Plan (03/H) system - Numbering Plan I OFL I PRG I SCR I DIR ‘----------------------------------------+---3-----+----+-Numbering Plan (03/U 1 +------------I------------------------------------+ I DGl I DG2 I DG3 I DG4 I f ---C------------------------~---~--~--~---No*’ Feature I I I 25 I Doorphone Call (l-4) ------------I 4 1 0 I I 20 I E x t e r n a l P a g i n g - - - - - - - - - - - - I 4 ' 1 ' 1 1 1 27 1 S t a t i o n P a g i n g - - - - - - - - - - - - - - I 4 1 2 i Paging Ansver ---------1 11 29 28 i1 Station External Paging Answer ------------I 44 1 1 43 I1 44 11 65 11 II 30 f 30 II Night Night Ansver Answer 21 -se--~------~ ---------------I t I 32 I Dial Call Pickup --------------I 4 I 7 I 4 1 8 1 1 I 33 I Directed Call Pickup --------I I 34 I Hold Extension Retrieve ---------I 4 I 9 I f 1 3 1 I 1 35 1 Redial --------------------I I I 36 I External Feature Access ---------I 5 I 0 I +----------------------------I---- . 1 1 I f I I Summary (Password level : Two or higher) The third screen of the System-Numbering Plan screen sets the feature numbers for functions 25 to 36. Assigning Items Doorphone Call (1-4) Default Fixed 1 Selection of Value Fixed 2 40 Enter one through four digits number consisting of 0 through 9, * , and #. External Paging 41 641 Reference 3-B-l .OO 4-G-7.00 5-E-2.00 6-H-4.00 3-B-l .OO 4-H-l .03 4-H-l .04 5-F-l .03 5-F-1.04 6-l-l .03 6-i-l .04 Continued Q-D-40 (70695) Assigning Items Default Selection of Value Referem Fixed 1 Fixed 2 Station Paging 42 642 3-B-1.00 4-H-1.01 4-H-1.02 4-H-1.04 5-F-1.01 5-F-1.02 5-F-1.04 6-t-1.01 6-I-1.02 6-t-1.04 External Paging Answer 43 643 3-B-1.00 4-H-1.03 4-H-1.04 5-F-1.03 5-F-1.04 Station Paging Answer 44 Night Answer 1 45 645 Night Answer 2 46 646 Dial Call Pickup 47 647 3-B-l.OC 4-D-3.01 5-B-l -01 Directed Call Pickup 46 646 3-B-1.00 4-D-3.02 5-B-1.02 Hold Extension Retrieve 49 649 3-B-l .OO 4-E-4.00 Enter one through four digits number consisting of 0 through 9, * , and #. 3-B-1.00 4-H-1.01 4-H-1.02 4-H-1.04 5-F-1.01 5-F-1.02 5-F-1.04 3-B-l.OC 3-B-8.02 3-D-2.OL 4-D-4.0( 4-I-1.01 5-B-2.OC 5-G-1.0' 5-c-3.oc *3 Redial External Feature Access 60 6~3 3-B-l.OC 5-A-2.03 650 3-B-l.OC 4-G-9.0( 5-E-3.OC 9-D-41 (70695) Description of Assigning Items Doorphone Call (l-4) Assigns the feature number for Doorphone calling. After dialing the feature number, dial 1 to 4 to specify the required doorphone. External Assigns the feature number for External Paging. After dialing the feature number, dial 0 (external pagers 1 and 2), 1 (external pager l), 2 (external pager 2), or w (all extensions and external pagers) Paging Station Paging Assigns the feature number for Internal Paging. After dialing the feature number, dial the paging group number (1 to 8), 0 (to page all internal zones) or x (to page all internal and external zones). External Paging Answer Assigns the feature number for External Paging Answer. After dialing the feature number, dial 1 (for pager 1) or 2 (for pager 2) Station Paging Answer Assigns the feature number for Station Paging Answer. Night Answer 1 Assigns the feature number for Night Answer 1. This feature number is used to answer calls assigned to UNA 1 in night service or TAFAS 1 in day service. Night Answer 2 Assigns the feature number for Night Answer 2. This feature number is used to answer calls assigned to UNA 2 in night service or TAFAS 2 in day service - Dial Call Pickup Assigns the feature number for Dial Call Pickup. This allows a user to pickup a call arriving at an extension in the same pickup group. Directed Call Pickup Assigns the feature number for Directed Call Pickup (General). This allows an extension user to pickup a call ringing at any extension in the same tenant. Hold Extension Retrieve Assigns the feature number for Hold Retrieving. This allows an extension user to retrieve a call held at another extension in the same tenant. Redial Assigns the feature number for Redial. This is used by an SLT to redial the last CO number. External Feature Access Assigns the feature number for sending a switchhook flash to a host or Centrex service. Conditions Refer to ‘Numbering Plan (01/l l).” 9-D-42 (70695) PBX Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in all setting screens. INDEX key is also available in this screen. The operation of function keys are described in Section 7-l ‘Operation of Function Keys.” Only a message is provided here. INDEX>Numbering Plan (01-l l)= 0 Continued Assigning items Default Selection of Value Fixed 1 1 F i x e d 2 Call Forwarding-Ail Call Set **2 Call Forwarding-Busy Set **3 Enter one through four digits number consisting of 0 through 9, * ,and #. Reference -. 3-B-l .oo 4-F-2.01 5-D-2.01 3-B-l -00 4-F-2.02 5-D-2.02 Call Forwarding-No Answer Set **4 3-B-l .OO 4-F-2.03 5-D-2.03 Call Forwarding-to Trunk **5 3-B-l .OO 4-F-2.05 5-D-2.05 Call Fonvarding-Busy/No Answer **6 3-B-l .OO 4-F-2.04 5-D-2.04 9-D-45 (70695) Description of Assigning Items Account Code Assigns the feature number for entering account codes which rnsy be forced or optional depending on system programming (Class of Service). Hold Assigns the feature number for Hold. This is used by an SLT to place the other party on hold. Hold Retrieve Assigns the feature number for retrieving Hold. This is used by an SLT to retrieve a held call. Call Assigns the feature number for Call Park-System. This is used by any extension user to park a call in one of twenty system call park zones. Park-System Call Park Retrieve-System Assigns the feature number for retrieving a call parked by Call System. Call Assigns the feature number for Call Park-Station. This is used by any extension user to park a call in that extension’s call park zone. Park-Station Park- Call Park Retrieve-Station Assigns the feature number for retrieving a call parked by Call Station. Call Forwarding-All Call Set Assigns the feature number for Call Fomarding Call Forwarding-Busy Set Assigns the feature number for Call Forwarding of extensions. Call Forwarding-No Answer Set Assigns the feature number for Call Forwarding of calls to no answer extensions. Call Forwarding-to Trunk Assigns the feature number for Call Forward to an outside party. Call Forwarding-Busy/No Answer Assigns the feature number for Call Forwarding of calls to extensions which are in busy or no answer status. Conditions Refer to ‘Numbering Plan (01/l l).” g-D-46 (70695) Park- of all calls. calls to busy Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in all setting screens. INDEX key is also available in this screen. The operation of function keys are described in Section 7-1 “Operation of Function Keys.” Only a message is provided here. INDU(>Numbering Plan (01-l l)=B B a H 9-D-47 (70695) B H=IT B - - - - - - - - - - - - - - - - - - - - - - - - +- - +- - ~- -+- - 6.05 Numbering Plan (05Ml) ~srstem - Numbering Plan I OFL I PRG I SCR 1 DIR Numbering Plan (OS/ll) +------e--- -------___---------se ---- - ----- --w--e----+ I No. I Feature I DGl I DG2 I DG3 I DG4 I ----+------------------- - - - - - - +--*---+w---+--i 49 I Do Not Disturb Set ------------I * I t I 1 I I 50 I Call Forwarding/Do Not Disturb Cancel -I il I P i 0 I I 51 I Dial Call Pickup Deny Set -------I 6 1 1 I * I I 5 2 1 Dial Call Pickup Deny Cancel -------I 6 I 1 I # I I 53 I C a l l W a i t i n g S e t - - - - - - - - - - - - I 6 I 2 I * I I I l i Call Vaiting 1I 54 55 1I BWOHCA D e n yCancel S e t ------------------ - - - I 6 I 23 I *1 I II 557 6I BIUSY BWOHCA OverrideDDeny e n y Set C a-------I n c e l - - - - - - - - - - -6 - I 1 6 4I 31 I ::e I1 I f I 58 I BUSY Override Deny Cancel --------I 6 I 4 I * I 1 59 1 data Line Security Set - - - - - - - - - I 6 I 5 I * I I 6 0 I Data Line Security Cancel --------I 6 1 5 1 # 1 +_-----____l___--l----,--~-~-~----------+ I I I CONHON 3 INDEX ! I 1 fl HRD CPY ! iii Summary The fifth screen of the System-Numbering Plan screen, constructed with nine screens, sets feature numbers for executing or canceling Assigning Items Default F i x e d 1 1 Fixed2 Do Not Disturb Set **1 Call Forwarding/Do Not Disturb Cancel ##O various functions. (Password level : Two or higher) Selection of Value 3-B-l .OO 4-D-6.00 5-B-4.00 3-B-l .OO 4-O-6.00 4-F-2.0 1 Enter one through four digits number consisting of 0 through 9, * , and #. Dial Call Pickup Deny Set 61s Dial Call Pickup Deny Cancel 61# Reference to 2.05 3-B-4.00 j-D-2.01 to 2.05 3-B-l -00 4-D-3.03 5-B-1.03 Continued Continued Assigning Items Default Selection of Value Fixed 1 1 F i x e d 2 Call Waiting Set 62s Call Waiting Cancel 62# BSSlOHCA Deny Set 63x BSS/OHCA Deny Cancel 63# Reference 3-B-l .OO 4-D-7.00 5-B-5.00 Enter one through four digits number consisting of 0 through 9 , n, and #. 3-B-l .OO 4-D-2.03 64* 3-B-l .OO 4-D-5.00 5-B-3.00 Data Line Security Set 65* 3-B-l .OO Data Line Security Cancel 6% Busy Override Deny Set Busy Override Deny Cancel 4-I-6.00 5-G-4.00 9-D-49 (70695) Description of Assigning Items Do Not Disturb Set Assigns the feature number for Do Not Disturb Set. Call Forwarding/Do Not Disturb Cancel Assigns the feature number for Call Forwarding /Do Not Disturb Cancel. . Dial Call Pickup Deny Set Assigns the feature number for Dial Call Pickup Deny Set. This allows an extension user to prohibit other extensions from answering calls arriving at his extension. Dial Call Pickup Deny Cancel Assigns the feature number for Dial Call Pickup Deny Cancel. Call Waiting Set Assigns the feature number for Call Waiting Set. This allows an extension user to hear a call waiting tone when another call arrives during a conversation. Call Waiting Cancel Assigns the feature number for Call Waiting Cancel. BSS / OHCA Deny Set Assigns the feature number for BSS/OHCA BSS / OHCA Deny Cancel Assigns the feature number for BSS/OHCA Deny Cancel. BSS/OHCA Deny Cancel is used when the called extension is off-hook. BSS and _ OHCA allows a call to be made using the ICM button. BSS sets green 240 wink on the called party’s ICM button while OHCA allows Hands-free Answerback to PITS KX-T7130, KX-T12323OD or KX-T123235. Busy Override Deny Set Assigns the feature number for Busy Override Deny Set. Enabling this feature prevents other extensions from using Executive Busy Override on this extension. Busy Override Deny Cancel Assigns the feature number for canceling Busy Override Deny. Data Line Security Set Assigns the feature number for setting data communication mode. When set this feature prevents any call progress tones from being sent to the extension. Data Line Security Cancel Assigns the feature number for canceling data communication mode. Conditions Refer to ‘Numbering Plan (01/l 1)” 9-D-50 (70695) Deny Set. Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in all setting screens. INDEX key is also available in this screen. The operation of function keys are described in Section 7-l ‘Operation of Function Keys.” Only a message is provided here. INDEXBNumbering Plan (01-l l)=fl m B B 9-D-51 (70695) B OMIT B 6.06 Numbering Plan (06/11) System - Numbering Plan I OFL I PRG I SCR I DIR ----------- -------_ ----------------------------+ -----+-----+--+--, Humbering Plan (OS/U) +-----------~--~----~------------------------~~+ I No. I Feature I DGl I DG2 I DG3 I DG4 I I - - + -- - - - - - - - - - - - - - ------- -..----+---+-------+----+----I I 6 1 i P i c k u p D i a l i n g Prommmins - - - - - - - - I 6 l 6 I 0 I I 62 l Pickup Dialing Set -----------I 6 1 6 1 $ 1 I Pickup Dialing Cancel ----------I 6 1 6 1 f) 1 I 64 I Absent Wessage Set --------------I t I 4 I I 65 I Absent Hessage Cancel .------------I # I 4 I 1 I 63 I I 66 I Timed Reminder Confirm ---------I * I 5 I 0 I i I 67 I Timed Reminder Set ------------I * 1511 I I 68 I Timed Reminder Cancel ----------I (I 1 5 1 I t I 69 I Voice Calling Hode Set -------I 6 1 7 I t I I 70 I Voice Calling Hode Cancel --------I 6 I 7 I 0 I I I 71 I Voice Calling Denr Set ---u---m IS I8 I*1 6 I 8 I t I I I 72 I Voice Calling Deny Cancel -------I +------ - - - - - - - - - - - ------------------------+ Summary (Password level : Two or higher) The sixth screen of the System-Numbering Plan sets the feature numbers for executing or canceling various functions. Assigning Items Default Pickup Dialing Programming 660 Pickup Dialing Set 66* Pickup Dialing Cancel 66iY *4 6~4 Absent Message Cancel #4 6#4 Confirm Timed Reminder Set Reference 3-B-l .OO 3-A-2.04 Absent Message Set Timed Reminder Selection of Value Fixed 1 1 Fixed 2 Enter one through four digits number consisting of 0 through 9, * ,and #. 3-B-1.00 4-l-7.00 5-G-5.00 *50 3-B-l .OO 4-I-3.00 w51 3-B-l -00 4-I-3.00 5-G-3.00 * Continuec 9-D-52 (70695) Continued Assigning Items Timed Reminder Cancel Default Fixed 1 Fixed 2 #5 Selection of Value 3-6-l .oo 4-I-3.00 5-G-3.00 #50 Voice Calling Mode Set 67* Voice Calling Mode Cancel 67# Voice Calling Deny Set 68* Voice Calling Deny Cancel 68# Reference .r Enter one through four digits number consisting of 0 through 9, * , and #. 3-B-l .OO 4-c-5.03 3-B-1 .OO 4-D-2.02 9-D-63 (70695) Description of Assigning Items Pickup Dialing Programming Pickup Dialing is a feature of SLT telephones which allows automatic calling when going off-hook. This feature allows the extension user to program the number to be called. Pickup Dialing Set This feature number enables Pickup Dialing. Pickup Dialing Cancel This feature number cancels Pickup Dialing. Absent Message Set Assigns the feature number for setting Absent Message. This is used by a user when he wants to inform callers of the reason he is away from his desk. The message will only appear on PITS equipped with display or Attendant Consoles. Absent Message Cancel Assigns the feature number for canceling Absent Message. Timed Reminder Confirm Assigns the feature number for confirming the time set by Timed Reminder. This feature is available only for PITS equipped with display. Timed Reminder Set Assigns the feature number for setting Timed Reminder. Timed Reminder Cancel Assigns the feature number for canceling Timed Reminder. Voice Calling Mode Set Assigns the feature number for setting Vojce Calling Mode. This is set at the calling extension. Voice calling uses the ICM button to make an announcement through the speaker of the called’extension when the called extension is idle. Voice Calling Mode Cancel Assigns the feature number for canceling Voice Calling Mode. This sets signal alerting. Voice Calling Deny Set Assigns the feature number for setting Voice Calling Deny. This is set by the called extension to deny voice calling. If “Voice Calling Deny” is set, the extension rings as usual (not voice alerted) when it receives a call. Voice Calling Deny Cancel Assigns the feature number for canceling Voice Calling Deny. Conditions Refer to ‘Numbering Plan (01/l l).” 9-D-54 (70695) _ Function The following functions appear on the function line of this setting screen. / &GOMMON@NDEX fiiJ 8 I I COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in all setting screens. INDEX key is also available in this screen. The operation of function keys are described in Section 7-l ‘Operation of Function Keys.” Only a message is provided here. INDEX>Numbering Plan (01-l 1)=[1 pJ B H 9-D-55 (70695) B HEXIT B 6.07 Numbering Plan (07/l 1) stem - Numbering Plan I OFL I PRG I SCR I DIR Numbering Plan (07/U) +--------------------------------------------------~ I No. I Feature I DGl I DG2 I DG3 I DG4 I I -s-e+-----------------------s--- - - + - - - + - - - V + - - + - - ‘ - ’ I 73 I Speed Dialing - Station Programing --I 6 1 t I I I 74 I Station Lock Set --------------------I r I 6 I I I I 75 1 Station Lock Cancel -------------I IF 1 6 i 1 1 1 76 walking ms Set - - - - - - - - - - - - - - - - 1 G 1 7 1 I I77 Walking COS Cancel - - - - - - - - - - - - - - 1 p 1 7 1 W a l k i n g S t a t i o n S e t I * I 8 1 I i 78 I 0 1 8 1 / I 79 Velking Station Cancel HesageS& -----------------I * 1 9 1 I Hesage Cancel - - - - - - - - - - - - - - - - I t 1 9 1 I_ I_ I 82 1 Station Program Clear - - - - - - - - - - - - 1 # 1 0 1 # 1 1 I 63 I Hessase Vaiting Reply ----------I 5 I 7 I t i I 84 I TIE Trunk Access -----------I 8 1 4 1 + - B - B - - - - _ - - - - - - - - - - - - B - - - - - - - ---------+ Summary (Password level : Two or higher) The seventh screen of the System-Numbering Plan sets feature numbers for executing or canceling various functions. Assigning Items Default Fixed1 Selection of Value Fixed 2 Speed Dialing-Station Programming 6* 6*5 Station Lack Set *6 6*6 Station Lock Cancel #6 6#6 Walking COS Set *7 6~7 Walking COS Cancel #7 6#7 Walking Station Set *8 6*8 Reference 3-B-l -00 5-A-2.01 3-B-l .OO 4-l-9.00 5-G-7.00 Enter one through four digits number consisting of 0 through 9, * , and #. 3-B-1.00 4-c-9.00 5-A-7.00 3-B-l .OO 3-F-3.00 Continued 9-D-56 (70695) Continued Assigning Default items I Walking Station Cancel Fixed 1 Fixed 2 #8 6#8 I Message Set I *9 Message Waiting Reply 6*9 1 1 6#9 ### 57 #1# 657 Reference 3-B-l .OO 3-F-3.00 I Message Cancel Station Program Clear Selection of Value Enter one through four digitsnumber consisting of 0 through 9 , * , and #. 1 5-G-6.00 3-B-l .OO 4-I-8.00 5-G-6.00 6-J-4.00 3-B-l .oo 4-l-l 0.00 5-G-8.00 5-G-6.00 3-F-1 4.00 TIE Trunk Access 9-D-57 (70695) Description of Assigning Items Speed Dialing-Station Programming Assigns the feature number for setting Speed Dialing to SLT(Single Line Telephone). Station Lock Set Assigns the feature number for setting Electronic Station Lock. When set the extension user cannot place outgoing CO calls from that extension. Station Lock Cancel Assigns the feature number for canceling Electronic Station Lock. Walking COS Set Assigns the feature number for setting Walking COS. This allows an extension user to temporarily change the COS of an extension to that of another extension. Walking COS Cancel Assigns the feature number for canceling Walking COS. Walking Station Set Assigns the feature number for starting to move a telephone set to another location. Walking Station Cancel Assigns the feature number for canceling the moved extension. Message Set Assigns the feature number for setting Message Waiting indication. This feature number is available only for SLT’s not for PITS%. Message Cancel Assigns the feature number for canceling Message Waiting indication. Station Program Clear Assigns the feature number for clearing data assigned by other feature numbers, such as Call Forwarding/Do Not Disturb/Timed Reminder, etc.. Message Waiting Reply Assigns the feature number for replying the Message Waiting Indication set by other extensions. This feature number is available only for a Single Line Telephone with MESSAGE lamp. TIE Trunk Access Assigns the feature number for TIE Trunk Access. Conditions Refer to ‘Numbering Plan (01/l l).” Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in all setting screens. INDEX key is also available in this screen. The operation of function keys are described in Section 7-l “Operation of Function Keys.” Only a message is provided here. INDEX>Numbering Plan (01-l l)=B H fj 9-D-58 (70695) B &Xl-r m 6.08 Numbering Plan (08/11) - Humbering Plan I OFL I PRG I SCR t DIR . - I - - - - - - - - - - - - - - - - - - - -- - - - + - - + - - + - - - + - . Numberins Plan (OS/l11 +-------- a - - - - - - - - - - - - - - - - - - - - - - + I Ho. I Feature i DGl I DG2 I DG3 I DG4 1 - - - - - - - - - - - - - ----+---- ----+--L-+---S I -be---------1 7 1 0 1 * 1 1 85 1 Hi&t Ho& Set --I I 8 6 I Nisht Ho& Cancel - - - - -l 7 I 0 I 0 I 1 87 1 Hi&t Service Hard We Set ------I 7 f 1 1 f 1 I I 88 I Hi&t Service Hanual Wade Cancel ---I 7 I 1 I # I I 89 I Flexible Hi& Service -------- l 7 I 2 I 1 I 90 I Remote Station Lock Set ------- 1 7 1 3 1 * f I 91 I Remte Station Lock Cancel -------I 7 I 3 I * I 1 I 9 2 I R e m o t e DHD S e t - - - - a - - ---l 7 I 4 I * I I 93 i Remote DND Cancel -------I 7 I 4 I p I 1 I 9 4 I R e m o t e FUD C a n c e l - - - e - v - - - 17151 I I I 95 I Renote FUD Cancel - One Time -----I 7 1 6 1 I 1 9 6 i BGW lhroush E x t e r n a l Paser - - - - - - - I 7 I 7 I I I + - - I - - - - - - - - - - - - - - - - - - - d - w -mB---+ hstem Summary The eighth screen of the System-Numbering Plan sets feature numbers for executing or canceling various functions. Assigning Items Night Mode Set (Password level : Two or higher) Default Fixed1 70* Selection of Value Fixed 2 3-0-8.05 4-I-1.03 5-G-1.03 69* Night Mode Cancel 70# 69# Night Service Manual Mode Set 71* 51* Night Service Manual Mode Cancel 71# 51# Flexible Night Service 72 520 Referent3 Enter one through four digits number * consisting of 0 through 9, 3~. and #. 3-B-1.00 4-I-1.03 5-G-1.03 6-J-1.02 3-B-1.00 3-B-8.03 4-l-1.02 5-I-1.02 6-J-1.01 Continued 9-D-59 (70695) . Continued Assigning Default items Remote Station Lock Set I 73* I 53* Remote Station Lock Cancel 73# 53# Remote DND Set 74* 54* Remote DND Cancel Remote FWD Cancel Selection of Value Fixed 1 1 Fixed 2 I I 74# I 75 Remote FWD CancelOneTime 76 BGM Through External Pager 77 Referencc 3-&l .oo a-1 1 .oo j-G-9.00 3J-5;OO I Enter one through four digits number consisting of 0 through 9, * , and #. 677 9-D-60 (70695) 3-B-1 .OO t-H-2.00 j-F-2.00 3-l-2.00 . Description of Assigning items Night Mode Set Assigns the feature number for setting Night mode manually (for operator 1 only). This is used when night mode is set to ‘Manual.” Night Mode Cancel Assigns the feature number for setting Day mode manually (for operator 1 only). Night Service Manual Mode Set Assigns the feature number for starting Night Service mode manually (for operator 1 only). This is used when night mode is set to “Auto.” Night Service Manual Mode Cancel Assigns the feature number for starting Night Service mode automatically (for operator 1 only). Flexible Night Service Assigns the feature number for setting an answering point in Night mode (for operator 1 only). Remote Station Lock Set Assigns the feature number for setting Electronic Station Lock to extensions (for operators 1 and 2 only). Remote Station Lock Cancel Assigns the feature number for unlocking extensions (for operators 1 and 2 only). Remote.DND Assigns the feature number for setting Do Not Disturb to extensions (for operators 1 and 2 only). Set Remote DND Cancel . Assigns the feature number for canceling Do Not Disturb for extensions (for operators 1 and 2 only). Remote FWD Cancel Assigns the feature number for canceling Call Forwarding feature for extensions (for operators 1 and 2 only). Remote FWD CancelOne Time Assigns the feature number for canceling Call Forwarding feature for extensions only once (for operators 1 and 2 only). BGM Through External Paging Assigns the feature number for sending BGM (background music) through External Pager (for operator 1 only). Conditions Refer to ‘Numbering Plan (01/l 1)” 9-D-61 (70695) Function The following functions appear on the function line of this setting screen. 8 0 COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in all setting screens. INDEX key is also available in this screen. The operation of function keys are described in Section 7-l “Operation of Function Keys.” Only a message is provided here. INDEXBNumbering Plan (01-l l)= n fj e B 9-D-62 (70695) H @MIT m 6.09 Numbering Plan (09111) S y s t e m - Humbering Plan I OFL I PRG I SCR I DIR ----------““--‘-----------------------~---+-----+--~---. Xunbering Plan (09/11) +----------------------------------------------+ I No.1 Feature 1DGl 1DG2 I DG3 I DG4 1 I. ---+ . - - - - - - - - - - - - - - - - - - - - I - I - - - - - - - + - - - - + - 3 - - - ~ - - I 971 BUSY Out Trunk ---------e----1 7 1 8 1 1 1 I I 981 Unbusy Trunk - - - - - - - - - - - - - - - - - I 7 1 8 1 # 1 I 991 CM Record --------w-- - - - - - - - - 1 7 1 g 1 1 1 I I 100 I OGW PlaYback ----------------I 7 1 9 1 2 1 I 101 I UCD Log In -------------------I t. 1 0 1 # 1 0 J 1102 I UCD Los Out ---------------I I 103 I Remote Timed Reminder Confirm ------- I 7 I * 01 I I 104 I Remote Timed Reminder Set ---------- I 7 I C 11 I 105 I Remote Timed Reminder Cancel I----- \ 7 I 8 I f t I t I 106 I Call Forwarding-Follov WeSet 7 I I 107 I Call Forvarding-Follow He Cancel I * I t 8 1 I I 108 I (Reserve) COMbIN 1 INDEX .g I - I - I 1. IHRDCPYI - I - I 8 Summary The ninth screen of the System-Numbering Plan sets feature numbers for executing or canceling various functions. (Password level : Two or higher) Selection of Value Reference I 3-B-l .OO 3-F-8.00 8-J-10.00 3-B-l -00 3-F-4.00 6-J-8.00 Enter one through four digits number consisting of 0 through 9, * , and #. 3-B-1.00 4-D-8.00 5-B-6.00 4-I-14.00 6-J-l 3.00 Remote Timed Reminder Set Remote Timed Reminder Cancel 7*1 5*1 7# 50# Default Assigning I terns Selection of Value Fixed 1 1 Fixed 2 Call Forwarding-Follow Me Set **7 Call Forwarding-Follow Me Cancel Enter one through four digits number I consisting of 0 through 9, *, and #. **a Reference 4-?2*06 1 O-C-68.00 5-D-2.05 1 O-C-68.00 Description of Assigning Items Busy Out Trunk Assigns the feature number for manually putting a trunk into busy status (for operator 1 only). Unbusy Trunk Assigns the feature number for canceling Busy Out Trunk (for operator 1 0W. OGM Record Assigns the feature number for recording OGM (for operator 1 only). OGM Playback Assigns the feature number for playback of OGM (for operator 1 only). UCD Log In Assigns the feature number for setting extensions to UCD (Uniform Call Distribution) service. UCD Log Out Assigns the feature number for removing extensions from UCD service. Remote Timed Reminder Confirm Assigns the feature number for confirming the time set by Remote Timed Reminder. This feature is available for the Operator 1 and 2 at the Attendant Consoles or PITS with display. Remote Timed Reminder Set Assigns the feature number for setting Remote Timed Reminder. This feature is available for the Operator 1 and 2 at the Attendant Consoles or PITS with display. Remote Timed Reminder Cancel Assigns the feature number for canceling Remote Timed Reminder. This feature is available for the Operator 1 and 2 at the Attendant Consoles or PITS with display. Call Forwarding-Follow Me Set Assigns the feature number for setting Call Forwarding-Follow Me feature. Call Forwarding-Follow Me Cancel. Assigns the feature number for canceling Call Forwarding-Follow Me feature. Conditions Refer to “Numbering Plan (01/l l).” 9-D-64 (70695) Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in all setting screens. INDEX keys is also available in this screen. The operation of function keys are described in Section 7-l “Operation of Function Keys.” Only a message is provided here. INDEXaNumbering Plan (01-l l)= 0 B fTJ H Q-D-64-l (70695) H HEXIT m 6.10 Numbering Plan (10/M) I OFL I PRG I SCR I DIR 1 t S y s t e m - Number I ne PI an -------------------------------------------------------+-----+-----+-----t----- Nuaberine Plan (lO/ll) +---------------------------------------------------------------------+ I No. 1 Feature I DC1 I DC2 I DC3 I DC4 1 -----+---------------------------------------+-----t-----t-----t-----+ I 109 I Other PBX Extension Ol--------------I I 110 I Other PBX Extens I on 02----------------I I I 111 I Other PBX Extenslon 03------------I I 112 I Other PBX Extension 04--------------I i I : 1 : I 113 I Other PBX Extension 050------------I I 114 I Other PBX Extenslon OS-------------I I I : ; : I 115 I Other PBX Extension 07--------------l I 116 I Other PBX Extens t on 08------------I I t : ; : I I I17 I Other PBX Extenslon OS---------------I I - I I 116 I Other PBX Extensfon 10-------------I I I 119 I Other PBX Extension 11------------I I : 1 : I 120 I Other PBX Extension 12-----------l Il l t---------------------------------------------------------------------+ I$ COYYON I ) ; ; I 1 l 8 INDEX g Summary The tenth screen of the System-Numbering Plan sets the other PBX extension numbers for 01 through 12. (Password level : Two or higher) Default Assigning Items Other PBX Extension 01 through’ 12 Fixed 1 1 Fiied 2 blank Selection of Value Referem 3-B-l .OO 0 to 9: set ‘DGl” and leave ‘DG2” 3-F-14.0’ blank when the other P8X extek sion numbers are to be composed of three digits, and set both ‘DGl” and “DG2” when the other PBX extension numbers are to be composed of.four digits. Description of Assigning Items Other PBX Extension 01 through 12 Assigns the leading one or two digits of other PBX extension numbers. If you employ PBX Code method for TIE calls (See Section 3-F-14.00), this programming is not required. Conditions Other PBX Extension 01 through 12 Cannot include lljc” and “#‘#“. 9-D-64-2 (70695) 6.11 Numbering Plan (1 l/l 1) S y s t e m - Nsmberfng Plan I OFL I PRO I SCR I DIR --------------------------------------------------------+-----+-----+-----+----Numbering Plan (11/111 +------------------------------------------------------------- --.-----* I No. I Festare I DC1 I DG2 I DC3 I DC4 I I -----+---------------------------------------+-----+-----+-----~-----+ I 121 I Other PBX Extensl on 13--------------l I 1 2 2 I O t h e r P B X Extension 14---------------I I 123 I Other PBX Extension 15---------------l I 124 I Other PBX Extension IS---------------I I I 125 I Transfer I 5 I 8 I I 126 1 Conference I I I 5 I 9 I I 127 I (Reserve) I 1 2 8 I (R8serV6) I 129 I (Reserve) 1 130 1 (R898W8) i 131 1 (fteSerV.8) 1 132 1 (Reserve) . I jii CONNON g INDEX 5 H‘ e: HRD CPY I 5 if; Summary The eleventh screen of the System-Numbering Plan sets the other PBX extension numbers for 13 through 16 and feature number for Transfer and Conference. I Assigning Items Other PBX Extension 13 through’ 16 Default Fixed I I F i x e d 2 blank I Transfer 58 I 59 Conference (Password level : Two or higher) Selection of Value 0 to 9: set “DGl” and leave ‘DGr blank when the other PBX extension numbers are to be composed of three digits, and set both ‘DGl” and ‘DGY when the other PBX extension numbers are to be composed of four digits. Enter one through four digits number consisting of 0 through 9, * ,and #. 9-D-64-3 (70695) Fieferenc 3-B-1.00 3-F-14.0 5-D-1.00 5-E-1.00 Description of Assigning Items Other PBX Extension 13 through 16 Assigns the leading one or two digits of other PBX extension numb&s. If you employ PBX Code method for TIE calls (See Section 3-F-14.00) this programming is not required. Transfer Assigns the feature number for SLT Transfer Operation This feature number is available for an SLT user when “SLT Transfer Operation” (See section 10-C-53.00 “World Select 3 (WS3)“) is set to “Mode p. Conference Assigns the feature number for SLT Conference Operation. This feature number is available for an SLT user when “SLT Transfer Operation” (See section 10-C-53.00 “World Select 3 (WS3)n) is set to “Mode 2”. Conditions Refer to “Numbering Plan (01/l l).” Other PBX Extension 13 through 16 Cannot include “jcD and Y”. If Description of Assigning items Fixed Message (1 to 6) Fixed messages to be displayed on a PITS telephone with the display. These messages cannot be changed by system programming. Extension user can set the desired one to his or her PITS telephone set. If the message assigned contains parameters, these should be entered by the extension user. Flexible Message (07 to 16) Assigns variable messages to be displayed on a PITS telephone with the display. These messages can be assigned and changed by system programming. Extension user can set the desired one to his or her PITS telephone and if the message contains any parameters, these should be entered by the extension user. Conditions If “System-Operation”, Tenant Service is assigned to “Yes,” 10 flexible messages (7 to 16) can be split between tenants 1 and 2. To split them, ‘System-Tenant”, Absent Message Boundary is used. Six fixed messages cannot be split between tenants. They are used by both tenants in common. A flexible message in use by an extension user cannot be changed or deleted. If you attempt, the changed data cannot be saved and the following error message appears on the screen. ***** ERROR: Some extensions are using that message. Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in this setting screen. For operation, refer to Section 7-l “Operation of Function Keys.” SD-71 (30393) E. Group Screen 1 .OO Trunk Group 1 .Ol Trunk Group (l/2) koup - Trunk Group I OFL I PRG I SCR I SEL ““-“““---‘----------------------------+----+-----+----+--Trunk Group’ No. = 01 (l/2) +-------------------------------------------------+ I Type ----_-___----_ 1DDD I 1 Name --s---------l I ; I I I I I I Tenant -----I ----- -1 1 Incomins/Outsoins -------I Incoming Only Incoming Hode (Day) -----I DIL 1:l Incoming Hode (Night) ---I FLEXIBLE Intercept Routing (Day1 -I A T T (Trw:No.) Intercept Routing (Night11 E X TM02 (Trpe:No.J Toll Restriction Level --I 01 Toll Restriction Table --I 3 Dialing Plan -------I Type-A minute(s) (l-64) CO-CO Duration Limit ---I 3 Disconnect Time -----I 1.5 second(s) Pause Time ----------I 3.5 second(s) Hook Switch Flash Time --I None . I I I Summary The Group-Trunk Group screen consists of 16 groups, each of which includes two screens. This screen is the first screen used to assign various I Assigning Items 1 Default data for trunk groups. (Password level : Two or higher) Selection of Value 1 I Reference 3-B-7.05 3-c-l .Ol 3-c-1.03 3-c-4.00 3-D-2.03 3-D-2.07 3-F-l 4-M We DDD DDD FEX WATS PVL PBX DID TIE Name co A maximum of three digits consisting of characters, numbers and marks : Trunk group name 3-B-7.05 1 or 2 : tenant number 3-B-7.05 3-B-4.00 Tenant blank incoming/Outgoing Both-Way I : Direct Distance Dialing : Foreign Exchange : Wide Area Telecommunication Service : Private Line : Behind PBX : Direct inward Dialing : TIE Line Incoming Only : for Incoming calls only Outgoing Only : for Outgoing calls only : for both I Both-Wav 9-E-l (70695) 3-B-7.05 I Continued (2) Conditions for setting trunk groups If a trunk group changes “Group-Trunk Group”, Type assigned to “PVL” (Private Line) to another type and if any CO lines belonging to the trunk group are selected to be “PRV-CO” (Private CO) in “Extension-Station, Type/Number, those CO lines are canceled from “Extension-Station”, Type/Number automatically. 2. Single CO, Group CO setting If “Single CO” or “Group CO” is selected in ‘Extension-Station”, Type, (1)’ Conditions of assigning DN buttons l The designated CO line is assigned to a trunk group in Trunk-CO Line”, Trunk Group. The trunk group should have “Group-Trunk Group”, Type assigned to other than ‘PVL” or “DID.” (2) Conditions of setting ‘Incoming Mode (Day) 1) If “Incoming Mode (Day)” is changed from ‘DIL 1:l” to another mode, The trunk group changed to another mode in “Group-Trunk Group”, incoming Mode (Day) is assigned in “Trunk-CO Line”, Trunk Group. The Trunk-CO Line”, Direct Termination setting is canceled. 2) If ‘Incoming Mode (Day)” is changed from ‘DIL 1 :N” to another mode, “Group-Trunk Group”, Destination (DIL 1: N only) setting is canceled. (3) Conditions of setting “Type” Changing “Type” to ‘PVL” (Private Line) from any other modes cancels -Single CO” or ‘Group CO” assigned to a DN button of an extension belonging to this trunk group in ‘Extension-Station”, Type. It is impossible to change from ‘DID” or “TIF to any other modes and vice versa if any CO line in “Trunk-CO Line” belongs to the “Group-Trunk Group.” 9-E-6 (70695) 3. Other Conditions The following tabular listings of items by trunk group type shows the items that cannot be assigned (‘-“. IS displayed) when Incoming/Outgoing mode of the trunk group is set to “Both-Way (default).” Trunk Group(l/2) Type DDD FEX WATS PVL incoming/Outgoing Incoming Mode(Day) Incoming Mode(Night) Intercept Routing(Day) Intercept Routing(Night) ATT (l/2) or DIL1:l FLEXIBLE - PBX DID TIE Both-Way ATT (l/2) or DILl:l FLEXIBLE - - - blank blank blank blank blank blank blank blank - blank - blank - blank - - - 1 - - - blank blank Yes - - Trunk Group(2/2) Destination (DIL 1:N Only) Type and Number DID Digit Modification Table PBX Access Code (No Restriction) PBX Access Code (Restriction) 8 Cd-TIE Restriction I-I TIE-CO Restriction TIE Forced Account Code Mode TIE Incoming Delete Digit TIE Incoming Insert Dial l Yes - 1 - I Yes - - - I Yes - From software version 9.xX and above, Incoming/Outgoing mode of the trunk group with DID can be assigned to ‘Both-Way,” ‘Incoming Only,” or “Outgoing Only.” However, please select “Incoming Only” if DID lines are available with only receiving incoming calls in your area. [Note] When “Incoming Only” is selected in the trunk group with DID, the following items are assignable but they do not work at all in Incoming Only mode. l Disconnect Time l Pause Time l Hook Switch Flash Time l Max. Dial No. after EFA Signal 9-E-7 (70695)M ,. I - I Yes No cl blank - I If the following types are selected for “Incoming/Outgoing,” the items below cannot be assigned: Incoming/Outgoing I Items impossible to Assign incoming Only Toll Restriction Level Toll Restriction Table Dialing Plan PBX Access Code (No Restriction), (Restriction) Outgoing Only Incoming Mode (Day), (Night) Destination (DIL 1 :N Only) If the following types are selected for “Incoming Mode (Day),” the item below cannot be assigned: Incoming Mode (Day) AT-IDIL 1:l DISA TAFAS 1 TAFAS 2 Items Impossible to Assign Destination (DIL l:N Only) Type and Number If ‘System-Operation” External Paging 1,2 is set tonNo,” TAFAS l/TAFAS cannot be assigned to ‘Incoming Mode (Day).” When pressing the NEXT key, this screen changes as follows: Trunk Trunk Trunk Group + Group + Group No. 01 (l/2) No. 01 (2/2) No. 02 (l/2) Pressing the PREV key changes the screen in reverse order. SE-8 (79695) r Function The following functions appear on the function line of this setting screen. COMMON (SHO LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in all setting screens. INDEX, READ keys are also available in this screen. The operation of function keys are described in Section 7-l ‘Operation of Function Keys.” Only messages are provided here. 1 INDEX>Trunk READ>Trunk Group No. (01-l 6)= 1 Group No. (Ol-16)=1] 9-E-8-l (70695) 1.02 Trunk Group (2/2) IoK JPRG.JscR 1’s~~ Group - Trunk Group ------------------------------*------------------------------+-----+-----.+-----c---Trunk Group No. =‘Ol (22) c---------------------------------------------------------------------.‘C 1Destination (DIL 1:N Only) i TypeandNumta ‘I‘,.*I I 1 DDDigitModificationT&le ‘- - - - - - - - - - - - i s , - ;: ‘1 ’ I-tI - , I I - 1 PBX Access Code (No Restriction) I 1 PBX Access Code (Restriction) I 1 Max. Dial No. after EFA Signal --------------* ’ 0 ((531) ,, ,*- :f ,- I , - , ,- ,-, ,- ,-, ’ CO-m &h&on ------,,,,;,,,,,,-,,,, ’ yes 1 TIE- m R&&on ------_-_------_---_-- 1_ 1mFo&AccctuntC&M& ---------k- [ 1T[E m$ D&e Digit ------------------ 1 _ WI 1 m [nc&ng Insen Did -----------------_-. 1_ C---------------------------------------------------------------------~ I i I I I I I I I Summary The Group-Trunk Group screen consists of a maximum of 16 groups, each of which includes two screens. This is the second screen used to Assigning Default Items Destination (DIL 1 :N Only) Type and Number blank blank DID Digit Modification assign various data for trunk groups. (Password level : Two or higher) Table Selection of Value Type blank ICM PCKUP Em : : : : : destination if not assigned selecting intercom group selecting pickup group selecting extension Referends ‘3-B-7.05 3-D-2.01 Number blank : when “blank” is selected for type 01 to 32: pickup group number : three or four digits : extension number 1 to8 : intercom group number b l a n k1 to4 : table number .9-E!9. (70695). 3-B-7.05 3-D-2.03 ‘9-K-2.00 COMMON (SHO LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in all setting screens. INDEX, READ keys are also available in this screen. The operation of function keys are described in Section 7-l ‘Operation of Function Keys.” Only messages are provided here. INDEXBTrunk m H READ>Trunk Group No. (01-l 6)= 0 pJ B H Group No. (01-l 6)=n F4 : n SE-1 l-l (70695) B BEXIT H S y s t e m I Tenant 1 I ‘RK ri )UP 1 2 I -- -- -I 11 T ;rpl, II ,, Paging group 1 r 55 LT-l-l ICM group 3 Pas jing - group 2 -I s-e I fiCD1 FouP3 7 I CO1 **-******Con EXTl EXT2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..*o.ooMTn Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in this setting screen. For operation, refer to Section 7-l ‘Operation of Function Keys.” 9-E-l 6 F. Trunk Screen 1.00 CO Line . 1 OR. 1PRG t SCR 1DIR _-------------------,,------------------------------+-----+-----+-----~----- Trunk - CO Line . Trunk Equipment No. = 2021 +---------------------------------------------+ 1 TrunkGroup ______--____- 1 01 I 1 T&Name _------------- 1 24 I I Direct Termination ---------- I D N : 5004 I Night Answer Point flype:No.) -- I E X T : 401 I 1ndM& ______-_____---_1Dm I 1 DTMFDurationTii -------- 1 80 I msecond(s) I I 1 p&efjpe& ______________- 1 - I 1% B& _________________ 1- $ 1 CKD&xtim - - - - - - - - - - - - - 1 54 msecond(s) I I 1 Sm&raagemnt ___________ 1 1 Wmk Signal Time Out -------- 1- 44 mesecond (s) c-----------------------‘-----‘--”------------------+ Tt COMMON m INLEX .‘. fhtEAD!l ii khRDcPY . 1 !I @ Summary Assigns various parameters for CO lines. This screen does not appear if any CO trunk card is not assigned in Configuration-Slot Assignment screen. Assigning Items Trunk Group Default Physical number Termination Selection of Value 01 to 16 : trunk group number 01 : for CO 15:forTIE 1 6 : f o r D I D Trunk Name Direct 144 screens are provided for CO Line. (Password level : Three or higher) blank : for ‘%vith ATLC” Directory number : for “wiiout ATLC” in physical number order of extensions paired with CO lines Reference 3-B-7.05 A maximum of ten digits composed of letters, numbers and symbols : no trunk name programmed blank 4-~-4.04 DN and directory number (three or four digits): call destination (Extension, Remote FDN, UCD FDN) None : no directtermination 3-D-2.01 fi-r+:m, *a# -_ - - Continued Assigning items Default Selection of Value Night Answer Point (Type : No.) Directory number : for each extension in physical number order Type (select input) None : no Night Answer Point UNA : Universal Night Answer EXT : Extension User RMT : Remote Administration NAG : Night Answer Group No. 1 or 2 : for ‘UNA” three or four digits : extension number for “EXT” Dial Mode (for U.S.A. and Canada) DTMF : DTMF mode DTMF Pulse : Pulse mode ’ MFC-R2 : MFCX2 mode (for areas other than U.S.A. and Canada) Pulse Refyence 3-B-8.00 lo-c-59.00 3-c-3.00 lo-c-51.00 3-B-10.00 DTMF Duration Time (for U.S.A. and Canada) 80 ms (for areas other than U.S.A. and Canada) blank 80 msIl60 ms : duration time Pulse Speed Low Speed/High Speed : pulse speed None 60% / 67% : % break lo-c-51.oc % Break (for U.S.A. and Canada) blank (for areas other than U.S.A. and Canada) Low Speed (for U.S.A. and Canada) blank ’ (for areas other than U.S.A. and Canada) 60% CPC Detection (4OES) Start Arrangement Wink Signal TimeOut Send Delay Wink (1.;: s) 00 01 02 to 75 : unavailable for CPC detection : 6.5 ms detection : 8 N ms detection Immediate Start Send Delay Wink 1: 64ms 2: 128ms . . . 127 : 8.128 s 9-F-2 VOfW(F) : immediate start type : wink start type 3-B-10.00 3-F-7.00 10-G49.oc 3-D-2.03 Description of Assigning Items Trunk Group Assigns the trunk group number of the CO line. Trunk Name Assigns the name of the CO line. This will appear on the CRT screen of the Attendant Console and the display of PITS telephone (if provided) when making or receiving a CO call. Direct Assigns the directory number of the destination, when the trunk group of the line is set to ‘DIL 1:l” in Incoming Mode (Day). Termination Night Answer Point (Type : No.) Assigns Night Answer point when the ‘Incoming Mode (Night)” is assigned to “FIXED” or “FLEXIBLE.” “NAG” can be selected only when Trunk Group “Incoming Mode (Night)” is assigned to “FIXED.” If it is not assigned to ‘FIXED” nor “FLEXIBLE,” &-” appears in the setting field, and it is impossible to assign a destination. Dial Mode Assigns the dial type (DTMF, Pulse or MFC-R2). This is the output mode regardless of the dial mode of the telephone used. If Pulse is selected, refer to Section 10-C-51 .OO “World Select 1 (WSl) about the following items. l Interdigit Pause l Pulse Type l % Break Detect DTMF Duration Time Assigns the duration of the DTMF tones sent. It is possible to assign this option only when the “Dial Mode” is set to ‘DTMF. When the dial mode is set to ‘Pulse,” this field is blank. Pulse Speed Assigns the pulse speed. It is possible to assign this option only when the “Dial Mode” is set to “Pulse.” When the dial mode is set to “DTMF,” this field is blank. % break Assigns the % break for pulse digits. This is the ratio between on and off hook signals during digit transmission. CPC Detection Assigns the expected minimum duration for detecting CPC (Calling Party Control) signal. Start Arrangement Assigns DIDTTIE/E&M start type. When the trunk group of the line is set to ‘DID/TIUE&M”, there are two methods of initiating a call. One is immediate start where the system outpulses the digits as soon as the trunk is seized and the other is where the system waits for a signal (wink start) from the far end before any digits are sent. Wink Signal Time-Out Assignable when Start Arrangement is set to “Send Delay Wink.” Conditions Before setting this screen, L%roupTrunk Group” screen must be programmed. This screen cannot be selected from Trunk-submenu screen, if no CO trunk card is programmed in ‘System-Configuration”, Slot Assignment. If any one of the CO trunk cards is programmed, this screen can be selected. g-F-3 (70695) When selecting “1. CO Line” in Trunk submenu screen, the setting screen which has the smallest Trunk Equipment No. appears on the screen first. If the “Group-Trunk Group” containing the CO line has Type” assigned to “DID,” the following items cannot be entered : ” -” is displayed : Direct Termination Night Answer Point (Type : No) l Dial Mode l DTMF Duration Time l Pulse Speed l % Break . CPC Detection l l If “the Group-Trunk Group” containing the CO line has “Type” assigned to anything other than “DID” or “TIE”, the following items cannot be entered : y -” is displayed : l l Direct Start Arrangement Wink Signal Time-Out Termination Night Answer Point (Type : No) . This is assignable only when the “Group-Trunk Group” containing the CO line has “Incoming Mode (Day)” assigned to “DIL 1:l ,” Otherfvise, y -” is displayed and setting is impossible. This is assignable only when the uGroup-Trunk Group” containing the CO line has “Incoming Mode (Night)” assigned to “FIXED” or ‘FLEXIBLE.” Otherwise, y -” I’S displayed and setting is impossible. When pressing the NEXT key, this screen appears in ascending order of Trunk Equipment number. After the largest number appears, the smallest one appears. Pressing the PREV key changes the screen in reverse order. Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in all setting screens. INDEX and READ keys are also available in this screen. The o@ration of function keys are described in Section 7-l “Operation of Function Keys.” Only messages are provided here. 1 INDEX>Trunk 1 READ>Physical Equipment No. (Physical No.)=0 No.=i I 9-F-4 (70695) - 2.00 Pager and Music Source Trunk - Pager & Uusic Source I OPL I PRG I SCR I DIR .-------------------------------------4----4----+--4-- Tone I BGH i I Tenant I -----------------+---------+-------+I I I Yes I I Ill 1 I Yes 1 External paser l----+--------4-----+-----I I I 2 I 1 I Yes I No +----------------------------+ I +--------------------------+ I Tenant I For Use I I I------ ~~ldumi i 11; 1 ---+----+---I I lioll%Btl4 I I21 1 I I Music Source I ------WV+ +-------------------- Summaiy Assigns external pagers and music sources. This screen does not appear when all the assigning items of ‘External Paging 1,2” and ‘External Assigning Items External Pager l/2 Tenant Music Source 1,2” are set to ‘No” in the Systern-operation (l/3) screen. (Password level : Three or higher) Selection of Value Default 1 1 2 : tenant 1 : tenant 2 Reference 3-D-2.04 4-D-4.00 4-H-l .03 4-H-l .04 4-H-2.00 5-B-2.00 5-F- 1.03 S-F-1.04 5-F-2.00 6-l-l .03 6-l-l .04 6-I-2.00 Continued 9-F-5 Description of Assigning Items UCD No. ( 1 to 4) UCD Time Table Assigns type of treatment for the calls arrived through UCD and placed in the Busy queue. Conditions To select this screen, press the NEXT key in the “System Attended-UCD (l/2)” screen. Pressing the TAB key moves the cursor as follows: Special Attended - UCD - m - - - - - m -- - - - - - - - UC0 u/21 ID T i n e T a b l e - I OR I PRG I SCR I SEL : ,----c-c _ I +-I OCDlb. I 4 I 1 -> R -> w -> 4T -> IT -> OFT -> -> I . -> I I -> -> I -> -> -> I I I “u -> ZI -> w -> 4T -> 42 -> 02u -> Tp -> -> -> -> -> -> -> -> -> I I i I 4 2 -> -> -> -> -> 1 &i -> 2-I -> II -> 4T -> 4T -> R -> I .I -> -> -> -> -> -> 4T -> -> -> 4T -> -> -> -> -> l -> -> . -> I I l cursor Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in this setting screen. For operation, refer to Section 7-l “Operation of Function Keys.” g-K-10 4.00 TIE Line Routing Table Special Attended -TIE Lii Routing Table 1 O F L 1 PRG 1 SCR 1 DIR -------------------------------------------------------------+-----+-----+-----+----TLE Line Routing Table (In) +---------------------------------------------------------------------~ I 1 I I 1 C&e 1 No. I Delete 1 Ipsert I Trunk Group Hunt Sequence I_--__--__-------____--------------. I I I Digit I Dial I 01 I 02 I 03 I 04 I 05 I 1 --me- I------+ -------.+ --------.+ e----. + -vm-v + -----.+ ----- +-----1 1 01 1 2xX I I 02 I I 31x 950 03 10419541 IO51 3 1 08 1 32 I I 3 I 06 07 I 2 0 3 3 I 1 I 1 I I 02 I 01 I 03 I 1011 I 02 I 01 I I 03 I 1 I I I I I I I 1 I I 1 109 I I101 I 11 I I I ‘I I I 12 I 4--------------------------------------------------------------------.~ Summary Assigns available trunk groups and parameters necessary for making TIE calls. Three screens are provided. Assigning Items Code Delete Digit Default blank 0 (Password level : Two or higher) Selection of Value Up to three digits : 0 - 9, X (wild card) 0 to 4 : number of deleting digit(s) Insert Dial blank Up to four digits : dialing number to be added Trunk Group Hunt Sequence blank 01 to 16 : trunk group number 9-K-l 1 mw Reference 3-F-l 4.OC Description of Assigning items Up to 36 routing patterns can be programmed in this table. This table is referenced by the system to identify the trunk route, when an extension user made a TIE call by dialing the feature number for “TIE Trunk Access” or ‘Other PBX Extension number. A routing pattern appropriate for each call is decided by the first three digits (except TIE trunk access code) of the dialed number. The sequence is used by both tenants but the trunk group will be skipped if it does not belong to the same tenant as the caller. . Code Assigns the leading one, two or three digits of the numbers for TIE calls. Used to determine which trunk group is used for a TIE call. Delete Digit Assigns the number of digits to be deleted from the beginning of the dialed digits. Insert Dial Assigns dialing number to be added to the beginning of the dialed digits. Trunk Group Hunt Sequence (01 to 05) Determines the trunk group hunt sequence to be used when p1acing.a TIE call. The sequence is used by both tenants but trunk group will be skipped if it does not belong to the same tenant as the caller. Conditions By pressing the NEXT Key, TIE Line Routing Table screens change as follows. 9-K-l 2 (70695) L. Miscellaneous Screen 1 .OO Installation Information iscel laneous - In&al lation Information I OFL I PRG I SCR I DIR --~-~~~~---“‘------~~-~~~-~-~~~~--~~~~----~~~~~-~--+---~ --+-----+--+------------------------------------------------------- << Customer h Installation Data >> : Customer Name : Location : Phone No. : Hodem no. Customer Contact : Date of Installation : : Unit ID : Installers Hame Progmmrs Naae : ------------------------------------------------------mnents: Panasonic Hybrid PBX Install Summary Assigns the customer’s name, address, telephone number etc., of the installation point. (Password level : Two or higher) Assigning Items Default Selection of Value Customer Name blank Letters, numbers, marks within 32 digits Location blank . Letters, numbers, marks within 64 digits Phone No. blank Letters, numbers, marks within 16 digits Modem No. blank Letters, numbers, marks within 16 digits Customer Contact blank Letters, numbers, marks within 32 digits Date of Installation blank Letters, numbers, marks within 16 digits Unit ID blank Referencc None Letters, numbers, marks within eight digits Continue g-L-1 Error Message No. 141 Countermeasure Probable Cause Attempting to remove an extension or trunk port Cancel the PFT assignment of the which is registered in Power Failure Transfer corresponding card, and then delete the port. (PFT) assignment. Impossible to change the Numbering Plan to Clear DN’s which should be blank. “Fixed,” because there exist DN’s which should be blank in the ‘Fixed” mode in the Hundred Block. 160 I impossible to change KM/Paging group, for the Change after deleting all the extensions in the pickup group belonging to the ICMlPaging pickup group. group contains extensions. I I I 9-M-6 (70695) 3.00 Other Error Messages Probable Cause Error Message Countermesure Illegal parameter Unacceptable value is assigned. Assign an allowable value. Parameter is not consecutive Space exits between items. Remove the space. This parameter cannot assign Assigned selection value is not for the item. Set the assignable value. Set the number different from the previous number. Duplicate parameter The number which is set previously in this definition internal screen is assigned again. Duplicate parameter The number which is set previously in a different Set the number different from the previous definition external screen is assigned. number. Not installed Device is not installed Assign the installed device. Invalid status Status of the specified device does not accept this command. Change the status of the device to be acceptable for the command. Diagnostic failure Diagnostic error is checked when In-Service command is executed. Execute test. Insufficient privilege Privilege level is lower than specified level. increase the privilege level through the Change level function. Failure Port test is made during a card malfunction. Repair the malfunctional card. Service violation Specified service is not executed. Check specified service. Already accessed by another device Another maintenance device (remote, PITS, system) is in use. Wait until another device is finished or let him finish. Printer is not ready Printer is not connected to the system or the power is off. Connect the printer, and make the power on. Cannot print out in remote Print out is unavailable from Remote. Execute print out on-site. Waiting Changing of program data is suspended because call placement is going on. Wait for a while or cancel the setting by “CTRL+C” I - I Calender IC trouble Calendar IC malfunction. Repair calender IC. Device error Backup device is not connected (only when maintenance device is ATT). Connect the backup device to SIO # 1 Port. Version error Different version at the time of backup. Match the backup version. Checksum error A checksum error has been detected. Communication line is defective, or backup data is destroyed. 9-M-7 I - Error Message I I Probable Cause Countermeasure illegal code detected Improper data is received. Communication link is defective, or backup data is destroyed. Off line Execution is impossible during off-line. Execute during on-line. Impossible change such as [INSI-& [INS], [OUSJd is attempted. Impossible. [OUS] Too many The number of equipment you attempt to equipment assigned. I assign is over the limit. Assign the equipment within the limit of Some extension are Attempting to change or delete the message using that message I which is in use by an extension user. Change or delete the message after the 9-M-8 (70695) Section 10 System Programming Dumb Type Terminal (Section 10) System Programming Dumb Type Terminal Contents Page 10-A-l A Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B 1 O-B-1 Construction of Programming Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ’ C Programming Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..-... 1 .OO System Assignment (SYA) ..................................................................... 2.00 Slot Assignment (SLA) ........................................................................... 3.00 DN Assignment (DNA) ........................................................................... 4.00 Operation (OPR) .................................................................................... 5.00 Tenant (TNN) ......................................................................................... 6.00 System Timer (TIM) ............................................................................... 7.00 Class of Service 1 (CSl) ....................................................................... 8.00 Class of Service 2 (CS2) ....................................................................... 9.00 Local Access Group (LAG) .................................................................... lo:00 Numbering Plan (NBP) .......................................................................... 11.00 Communication Interface (COM) ............................................................ 12.00 Speed Dialing-System (SPD) ................................................................ 13.09 Absent Message (ABS) ......................................................................... 14.09 TrunkGroup 1 (TGl) ............................................................................. 15.00 Trunk Group 2 (TGP) ............................................................................. 16.00 WI/Paging Group (IPG) ....................................................................... 17.00 Call Pickup Group (CPG) ....................................................................... 18.00 CO Line (COL) ....................................................................................... ..... .................................................................................... 19.06 Pager (PAG) 20.00 Music Source (MUS) .............................................................................. 21.00 Automatic Gain Control (AGC) .............................................................. 22.00 Extension (EXT) ..................................................................................... 23.00 DSS Console (DSS) .............................................................................. 24.00 DN Button Assignment (DNK) ............................................................... 25.00 PF Button Assignment (PFK) ................................................................. 26.00 DSS Button Assignment (DSK) ............................................................. 27.00 Doorphone (DPH) .................................................................................. 28.09 Attendant Console (ATT) ....................................................................... 29.00 Attendant Queue Priority (AQP) ............................................................ 30.00 Equal Access (EQU) .............................................................................. 31.00 OCC Access (OCC) ............................................................................... 32.00 Toll Restriction 1 (TRl) .......................................................................... 33.06 Toll Restriction 2 (TR2) .......................................................................... 34.00 Toll Restriction 3 (TR3) .......................................................................... 35.00 Automatic Route Selection 1 (ARl) ....................................................... 36.00 Automatic Route Selection 2 (AR2) ...................................................... 37.06 Automatic Route Selection 3 (AR3) ....................................................... 38.00 Automatic Route Selection 4 (AR4) ...................................................... 39.00 Automatic Route Selection 5 (AR5) ...................................................... 40.00 DISA (DIS) ............................................................................................. 10-l (70695)M 10-C-l 10-C-l 1 o-c-2 1 O-c-5 1 O-C-6 1 o-c-1 1 10-c-14 1 o-c-1 5 10-c-17 10-c-19 10-c-20 1 O-c-25 1 O-C-26 10-C-27 1 O-C-28 1 O-c-31 1 O-C-32 19-C-33 10-c-34 10-C-36 1 o-c-37 1 O-C-38 1 O-c-39 lo-c-42 10-c-43 10-C-46 10-C-48 1 o-c-50 1 O-c-51 1 O-c-53 lo-C-54 1 O-C-56 10-C-58 10-c-59 10-c-60 10-c-61 lo-C-62 10-c-63 lo-C-64 lo-C-65 10-C-66 . . Page 41 .OO DISA Code (DIC) ................................................................................... 42.00 DISA Password (DIP) ............................................................................ 43.00 DID (DID) ............................................................................................... 44.00 UCD 1 (UCl) ......................................................................................... 45.00 UCD 2 (UC2) ......................................................................................... 46.00 Information (INF) .................................................................................... 47.00 Power Failure Transfer (PFT) ................................................................ 48.00 Change Password (CHG) ...................................................................... 49.00 CPC Signal Detect Timing-Outgoing CO Calls (CPC). .......................... 50.00 Automatic Busy-Out Count (ABC) ......................................................... 51.00 World Select 1 (WSl) ............................................................................ ( 1 ) interdigit Pause.. .............................................................................. ( 2 ) Pulse Type.. ..................................................................................... (3) Automatic Redial Retry Count ......................................................... (4) Automatic Rediai Retry Interval ....................................................... (5) % Break Detect (SLT) ...................................................................... ............. (6) Flash Detect (SLT) ............................................................... (7) Flash Detect (TIE) ........................................................................... (8) Answer Decision Timer .................................................................... 52.00 World Select 2 (WS2) ............................................................................ ..‘................................... (1) First Dial Timer ......................................... (2) First Dial Timer (DID) ....................................................................... (3) EQU Access .................................................................................... (4) OCC Access .................................................................................... ( 5 ) Outgoing CO Back Tone.. ................................................................ ( 6 ) L-COT Busy Out Looprelay ............................................................. ( 7 ) G-COT Busy O u t Looprelay ............................................................ (8) Pay Tone Frequency ........................................................................ (9) Pay Tone Gain ................................................................................. 53.00 World Select 3 (WS3) ............................................................................ (1) DIL 1:N CO Key Only (PITS only) ................................................... (2) EXT Off-hook BLF (PITS only) ........................................................ ( 3 ) DTMF-Tone Integration.. ................................................................. (4) SLT On-hook Operation Mode ......................................................... (5) Mode Selection of Calls Arriving at ATT .......................................... (6) Centrex ARS .................................................................................... ( 7 ) Waiting for Second Dial Tone Mode ................................................ ( 8 ) Polarity Reversal Mode (Not available in your area) .............. . ........ (9) SC/# Allow Mode .............................................................................. (10) Message Waiting Lamp Off Control - Voice Mail .......................... (11) p law - A law (E-l only) (Not available in your area). ..................... (12) SLT Transfer Operation .................................................................. (13) Ringback Tone While Transfer ....................................................... 54.00 Voice Mail Directory number (VMD) ...................................................... 55.00 Mailbox Number (MBN) ......................................................................... lo-2 (70695)M 1 O-C-67 1 O-C-68 1 O-C-69 1 o-c-70 1 o-c-71 1 O-C-72 1 o-c-73 1 o-c-74 10-C-75 10-C-76 1 o-c-77 lo-C-77 10-c-77 10-c-77 10-c-77 lo-C-77 10-c-77 10-c-77 10-C-77’ 1 o-c-79 10-c-79 1 o-c-79 1 o-c-79 1 O-c-79 1 O-c-79 1 o-c-79 1 O-c-79 1 O-c-79 1 o-c-79 10-C-81 1 O-C-81 1 O-C-81 1 O-C-81 1 O-C-82 1 O-C-82-l 1 O-C-82-l 1 O-C-82-l 10-C-82-1 1 O-C-82-l 1 O-C-82-2 10-C-82-2 1 O-C-82-2 1 O-C-82-2 1 O-C-83 1 O-C-86 . Page 56.00 Account Code Verified ........................................................................... (1) Programming the System Account Code -Speed Dialing Boundary (SPB) ..................................................... (2) Assigning Account Code Verified (ACV) Feature to the Extension ........................................................................................ 57.00 Account Code Entry on Long Distance Calls (ACL) .............................. 58.00 CO Access Instantly (CAI) ..................................................................... 59.00 Night Answer Group (NAG) ................................................................... 60.00 Polarity Reversal Detection (PRD) ........................................................ 61 .OO Waiting for Second Dial tone @/SD) ..................................................... 62.00 World Select 4(WS4) ............................................................................. (1) Dial Tone Frequency Selection ........................................................ (2) Paging Beep Tone Control ............................................................... (3) TAFAS Confirmation Tone Control ................................................... (4) Paging Confirmation Tone Control ................................................... (5) Call Park Confirmation Tone Control ............................................... (6) Call Pickup Confirmation Tone Control ............................................ 63.00 Equal Access Code (EQC) .................................................................... 64.00 T-l Related Commands ......................................................................... 64.01 Channel Assignment (CHA) -T-l ............................................ 64.02 System Clock Mode (CLK) - T-l ............................................... 64.03 Master Clock Priority (CLP) - T-l ............................................. 64.04 ESF Frame Option(EF0) - T-l ................................................. 65.00 TIE Line Related Commands ................................................................. 65.01 TIE Line Routing Table (TIE) ...................................................... 65.02 TIE Account Code (TAC) ............................................................ 65.03 TIE Trunk Relay Restriction (TRR) ............................................. 65.04 Line Hunting Sequence (LHS) .................................................... 67.00 DlSAlAGC Tone Detection Mode (TDM) ............................................... 68.00 Call Forwarding-Follow Me (CFM) ......................................................... 69.60 Limited Call Duration (LCD) ................................................................... D Error Message Tables ...................................................................................... 1 .OO Error Messages Related to the Assigning Items in the Same Command ..................................................................... 2.00 Error Messages Related to the Assigning Items in the Other Commands .................................................................... 3.00 Fixed Error Messages ............................................................................ 4.00 Other Error Messages ........................................................................... 10-3 (70695)M 1 o-c-90 1 O-c-90 1 o-c-91 10-C-93 1 o-c-95 1 O-c-97 10-c-100 10-c-103 1 O-c-1 05 10-C-l 05 10-c-105 10-C-105 10-c-105 10-c-105 10-c-105 1 O-C-1 07 10-C-109 1 O-c-1 09 10-c-111 10-c-112 10-c-113 10-c-120 10-c-120 10-c-121 10-c-122 10-C-123 10-c-130 10-c-131 10-c-132 10-D-l 10-D-l 10-D-2 10-D-6 10-D-8 - . A. Introduction This section provides system programming using Dumb type terminal. Before starting system programming, Section 8 “Preparation for Programming and Maintenance (Dumb Type Terminal)” must be read. This section describes the basic operations for programming. Programming mode consists of a variety of commands, which enable users to assign or change various parameters concerning the system administration such as Tenant, Class of Service, Numbering Plan and so on. A list of all programming commands is provided on the following page. 1 O-A-1 (70695) B. Construction of Programming Mode Pas.yword Level 1PRG (Programming) -r-f SYA (System Assignment) - TIM (System Timer) ti - CSl (Class of Service 1) - CS2 (Class of Service 2) (Local Access Group) -- NBP (Numbering Plan) I- -4 L COM lCommunication Interface) ‘- SPD iSpeed Dialing - System) ’ ‘- ABS (Absent Message) ‘- TGl (TrunkGroup 1 ) TG2 hrunk GrouD 2i - - - IPG (ICM/Paging Group) --- CPG (Call Pickup Group) - -- COL (CO Line) --- PAG (External Paging) - - - MUS (Music Source) - - - AGC (Automatic Gain Control) r -4 EXT IExtension) 11 ‘I -T- 2 ; 2 2 I ! 21 3 3 2 21 2 2 3 3 3 3 3 Third S e t Continued - WS3 (World Select 3) 2 - CAI (CO Access Instantly) 2 - ACV (Account Code Verified) 2 , - - - ACL (Account Code Entry on Long 2 Distance Calls) --- SPB (Speed Dialing Boundary) 2 - - - NAG (Night Answer Group) 2 --- PRD (Polarity Reversal Detection) 2 r-TL VMD (Voice Mail DN) 2 I --- MBN (Mail Box Number) 2 --- WSD (Waiting for Second Dial Tone) 2 --- EQC (Equal Access Code) 2 - - - WS4 (World Select 4) 2 - - - TAC (TIE Account Code) 2 - - - CLK (Clock Mode) 2 21 1-1 CLP (Clock Priority) LHS (Line Hunting Sequence) E F O ~ESF Frame-Option) 21 . 2 -- LCD (Limited Call Duration) CFM (Call Forwarding-Follow Me) 2 L-1 1 O-B-2 (70695)M These programs must be done in order from “First Ser “Second Ser to “Third Set” shown in the table. For example, if you program Operation (OPE) before doing System Assignment (SYA) program, an error message appears. ; I I I I I I i II i i C. Pr*&amming Commands 1.00 System Assignment (SYA) Description This command is used to configure the system for: l Expansion Shelf (I, or both 1 and 2) l T-SW Conference Expansion Card To expand the conference trunks, T-SW Conference Expansion Card (KX-T336104) must be installed. (Password level : One) Input Format Input Value for Item Number Item Assigning Items NUTlber 1 Expansion 2 TSW Additional CONF Input Value Shelf 1 N : expansion shelf not installed 1: expansion shelf 1 available 2 : both expansion shelves 1 and 2 available Y : conference expansion card installed N: conference expansion card not installed conditions None 10-C-l 2.00 Slot Assignment (SLA) Description To assign the type of card equipped in each free slot on the basic and expansion shelves. (Password level : One) Input Format * In the AT mode, to display or edit in the conversation style, do not enter the index number : When you enter; PRG>SlA AT (d ), the display starts from the slot number 101 and moves one by one. Index Number Explanation Index Number Physical number (101 to 315) XXX - slot (01 to 15) T shelf (1 to 3) . . Input Value for Item Number :em hJtnber 1 Input Value Assigning I terns Card Type XX (00 to 18) (Version 12.xX) 00: none 01 : PLC (Proprietary integrated Telephone System Line card Circuil 02 : HLC (Hybrid Line Circuit) card 03 : SLC (Single Line Telephone Circuit) card 04 : MSLC(SLC with Message Waiting) card 06 : LCOT (Loop Start Central Office Trunk) card 07 : GCOT (Ground Start Central Office Trunk) card 08 : DID (Direct Inward Dialing) card 10 : T-l (T-1 DIGITAL TRUNK CARD) 12 : AGC (Automatic Gain Control) card 13 : DISA (Direct Inward System Access) card 14 : OPX (Off Premise Extension) card Continued 1 O-c-2 (70695)M Continued I tern rJurnbzr Input Value Assigning Items 15 : ATLC (Attendant Console Line Circuit) card 16 : DPH (Doorphone Circuit) card 17 : RMT (Remote Circuit) card 18 : OHCA (Off-Hook Call Announcement) card Conditions If “SLA” command is entered without index number, all physical slot numbers (except 113 and 115) will be displayed in ascending order (from 101 to 315). It is impossible to select Index No.1 13 and 115, because Index No.1 13 is fixed to CPU card and 115 is fixed to T-SW card. If Index No.1 14 is selected, assignable input value is limited to ‘00: none” or ‘18: OHCA.” T-l card should be assigned to FSOl (05 or 09 of any shelf. One T-l card occupies three slots. If you assign a T-l card to FSOl , FS02 and FS03 are not available for other cards. ‘* * *” is displayed in these two slots and the cursor skips them. l If no CO trunk card is assigned, it is not possible to program ‘CO Line (COL).n If AGC card is not assigned, =Automatic Gain Control (AGC)n cannot be programmed. If DPH card is not assigned, “Doorphone (DPH)n cannot be programmed. If ATLC card is not assigned, it is not possible to program ‘Attendant Console (ATT)” and “Attendant Queue Priority (AQP).” If DISA card is not assigned, it is not possible to program and ‘DISA Password (DIP).” “DISA (DIS)“, ‘DISA Code (DIC) If DID card is not assigned, it is not possible to program ‘DID (DID).” When assigning a card, the card status ia Out of Service (OUS). When using the card, the card status should be set to In Service (INS). For ‘In Service (INS)” and “Out of Service (OUST, refer to Section 8-F-3.00 ‘In Service (INS)” and Section 8-F-4.00 “Out of Service (OUS).” For confirming whether card status is INS or OUS, refer to Section 15-F-1.02 ‘Card Status Screen.” 1 o-c-3 (70695)M . When deleting or changing the pre-assigned card type, the conditions should be the followings: l The card status is OUS or Fault. l All of the port data has been deleted. However, if there exist port data, it is possible to change the cards as follows: l PLC card UHLC card l SLC card WHLC card Deleting the ATLC card will be an error if there exist the following assignments: l “Trunk Group (TGl)“, incoming Mode (Day) is set to “1 (ATT).” Intercept Routing (Day) is set to nA (ATT).” * l “Doorphone (DPH)“, Doorphone Assignment is set to “A(AlT).” Deleting the DISA l “Trunk Group Incoming Incoming card will be an error if there exist the following assignments: CrGl)“, Mode (Day) is set to “4 (DISA).” Mode (Night) is set to “4 (DISA).” Deleting the HLC, SLC, LCOT or GCOT card will be an error if there is the following assignment to the slot to be deleted: l “Power failure Transfer (PFT) See Section l-A-5.00 “Service Cards Description” for installing the cards in combination. lo-c-4 (70695) 3.00 DN Assignment (DNA) Description To assign a DN (directory number) to each port. (Password level : One) Input Format Index Number Explanation index Number Physical number (101 to 315) -E.- slot (01 to 15) i” shelf (1 to 3) Input Value for Item Number . item Number Input Value Assigning Items 1 Port 1 2 Port 2 3 Port 3 4 Port 4 5 Port 5 6 Port 6 7 Port 7 a port a Three or four numeric digits: directory number Conditions None 1 o-c-5 When selecting “1. CO Line” in Trunk submenu screen, the setting the smallest Trunk Equipment No. appears on the screen first. screen If the “Group-Trunk Group” containing the CO line has Type” assigned tc following items cannot be entered : y -” is displayed : l l l l l l l Direct Termination Night Answer Point (Type : No) Dial Mode DTMF Duration Time Pulse Speed % Break CPC Detection If “the Group-Trunk Group” containing the CO line has Type” assigned tc other than “DID” or “TIE”, the following items cannot be entered : y -” is l l Direct Start Arrangement Wink Signal Time-Out Termination Night Answer Point (Type : No) . This is assignable only when the “Group line has ‘Incoming Mode (Day)” assign= displayed and setting is impossible. This is assignable only when the “Group line has ‘Incoming Mode (Night)” assignt Otherwise, ” -- is displayed and setting When pressing the NEXT key, this screen appears in ascending order of Equipment number. After the largest number appears, the smallest one Pressing the PREV key changes the screen in reverse order. Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD ( are available in all setting screens. INDEX and READ keys are also ava screen. The operation of function keys are described in Section 7-l “Ops Function Keys.* Only messages are provided here. 1INDEX>Trunk 1 READ>Physical Equipment No. (Physical No.)=1 No.=fl 9-F-4 (70695) ConJinued .em lumber 07 Assigning Items Home Dialing Plan Input Value A : Type-A : B : Type-B : C : Type-C : D : Type-D : l+NXX+NXX+XXXX NXX+XXXX NPX+NXX+XXXX NNX+XXXX 1 +NPX+NXX+XXXX 1 +NNX+XXXX NXX+XXXX 1 +NXX+NXX+XXXX NXX+NXX+XXXX NXX+XXXX (N: 2 to 9, P: O,l, X: 0 to 9) 08 DSS Operation Mode 1 : disconnect and call 2 : hold and transfer 09 Busy Tone 1 : busy tone 1 2 : busy tone 2 10 Held Call Reminder Y : Held Call Reminder is enabled N : Held Call Reminder is disabled 11. Beep Tone for Bsy-ovr / Brg-in Y : overriding with beep tone N : overriding without beep tone 12 External Paging 1 Y: using external pager 1 N : not using external pager 1 13 External Paging 2 Y : using external pager 2 N : not using external pager 2 14 External Music Source 1 Y : using external music source 1 N : not using external music source 1 15 External Music Source 2 Y : using external music source 2 N : not using external music source 2 16 Idle Line Preference 1 : off-hook selects an idle DN button 2 : off-hook selects an idle CO button 17 FDN for General Operatdr Call 1 0 : noFDN DN XXXX (XXXX: three or four numeric digits): FDN for genera operator call 1 18 FDN for General Operator Call 2 0 : no FDN DN XXXX (XXXX: three or four numeric digits): FDN for genera operator call 2 19 PBX Code 0 : noPBXcode Up to three numeric digits can be entered. . 1 O-c-7 (70695)M Description of Assigning Items UCD No. ( 1 to 4) UCD Time Table Assigns type of treatment for the calls arrived through UCD and placed in the Busy queue. Conditions To select this screen, press the NEXT key in the “System Attended-UCD (l/2)” screen. Pressing the TAB key moves the cursor as follows: Special - - I OR I PRG I !XR I Sn Attded - UCD - - - - - - - - UC0 c-- - - - - - l p - c 0 - - l Ua time T a b l e I 'EDHo. 1 4 I I . I - I l 1 --Ry -> 2T -> I -> Q -> 4T -> OFF -> -> -> -> -> -> I 1 -> -> -> -> I I “u -> 2T -> I -> 4T -> 4T -> TR -> -> -> -> -> -> -> -> -> -> I I n -> I -> 4T -> IT -> uzu -> TR -> -> -> -> -> -> -> -> I I . -> I I 2 I l 2T -> Ii -> 4T -> 4T -> -> -> -> -> -> -> -> -> l cursor Function The following functions appear on the function line of this setting screen. COMMON (SHOW LV, CHG LV, INS, OUS, REMOVE, EXIT) and HRD CPY keys are available in this setting screen. For operation, refer to Section 7-l “Operation of Function Keys.” g-K-10 7.00 Class of Service 1 (CSI) Description This is the first Class of Service block which is used to assign toll restriction level, maximum dialing digits, Call Forwarding, Do Not Disturb, Do Not Disturb Override and so on. (Password level: Two or higher) Input Format Index Number Index Number Explanation Class of Service number 01 to 32 input Value for Item Number Item . Nwnbs 01 Assigning Items. Input Value Toll Restriction Level (Day) 01 to 16 02 Toll Restriction Level (Night) 01 to 16 03 Max. Dialing Digits 002 to 255 : maximum number of dialed digits [input value -11 000 : no limit to digits dialed 001 : cannot dial 04 Call Forwarding/Do Not Disturb Y : Call Forwarding/Do Not Disturb is available N : Call Forwarding/Do Not Disturb is unavailable 05 Do Not Dkturb Override Y : Do Not Disturb Override is available N : Do Not Disturb Override is unavailable 06 CO Forward Mode Y : Call Fonnrarding to CO is available N : Call Fonvarding to CO is unavailable 07 CO Transfer Mode Y : Call Transfer to CO is available N : Call Transfer to CO is unavailable 08 Forced Account Code Mode Y : account codes are required for outgoing CO calls N : account codes are optional for outgoing CO calls 09 BSSIOHCA Y : Override is available N : Override is unavailable Continued lo-C-15 Description of Assigning items Up to 36 routing patterns can be programmed in this table. This table is referenced by the system to identify the trunk route, when an extension user made a TIE call by dialing the feature number for “TIE Trunk Access” or =Other PBX Extension number”. A routing pattern appropriate for each call is decided by the first three digits (except TIE trunk access code) of the dialed number. The sequence is used by both tenants but the trunk group will be skipped if it does not belong to the same tenant as the caller. . Code Assigns the leading one, two or three digits of the numbers for TIE calls. Used to determine which trunk group is used for a TIE call. Delete Digit Assigns the number of digits to be deleted from the beginning of the dialed digits. Insert Dial Assigns dialing number to be added to the beginning of the dialed digits. Trunk Group Hunt Sequence (01 to 05) Determines the trunk group hunt sequence to be used when p1acing.a TIE call. The sequence is used by both tenants but trunk group will be skipped if it does not belong to the same tenant as the caller. Conditions By pressing the NEXT Key, TIE Line Routing Table screens change as follows. g-K-12 (70695) Continued Maximum four digits consisting of numbers, * , # 10-C-23 t/osw Error Message No. I Probable Cause Countermeasure 141 Attempting to remove an extension or trunk port Cancel the PFT assignment of the which is registered in Power Failure Transfer corresponding card, and then delete the port. (PFT) assignment. 150 Clear DN’s which should be blank. Impossible to change the Numbering Plan to “Fixed,” because there exist DN’s which should be blank in the “Fixed” mode in the Hundred Block. 160 Impossible to change IClWPaging group, for the Change after deleting all the extensions in thy pickup group. pickup group belonging to the KM/Paging group contains extensions. Probable Cause Error Message I Illegal code detected r- I Countermeasure I I Communication link is defective, or backup I data is destroyed. improper data is received. Ofl line Execution is impossible during off-line. Execute during on-line. Status is already set Impossible change such as [INSH [ I N S ] . [OUSJ+ is attempted. Impossible. [CUS] Too many equipment assigned. The number of equipment you attempt to assign is over the limit. Assign the equipment within the limit of number. Some extension are using that message Attempting to change or delete the message which is in use by an extension user. Change or delete the message after the extension cancels the setting. 9-M-8 (70695) I 11 .OO Communication Interface (COW Description To set parameters for the RS-232C and Modem (Modulator and Demodulator) ports. (Password level: Two or higher) Input Format Index Number Explanation Index Number 1 SIO # 1 (terminal) 2 SIO # 2 (SMDR) 3 Remote Input Value for Item Number Ite mmber Assigning Items Nu 1 NL-code Input Value 1 : CR+LF 2: CR 2 Baud Rate 11 O/l 50/300/600/l 200/2400/4800/9600 300/1200 : for Remote 3 Word Length 6 : 6 bits (for Remote only) 7: 7bii 8: 8 bits 4 Parity 1 : none 2 : mark (for SIO only) 3 : space (for SIO only) 4: even 5: odd 5 Stop Bit 1 : 1 bit 2 : 1.5 bits (for Remote only) 3 : 2 bits : for SIO Conditions It is possible to change assigning items in ‘Communication Interface (COM)” while on-site administration or remote administration is performed or SMDR is being printed out. New setting becomes effective when those operation modes are finished. lo-C-25 Section IO System Programming Dumb Type Terminal Continued m mhnr Assigning Items Input Value Incoming Mode (Day) 1 : ATT (Attendant Console) 2 : DIL 1:l (Direct In Line 1:l) 3 : DIL l:N (Direct In Line 1:N) 4 : DISA (Direct Inward System Access) 5 : TAFAS 1 (Trunk Answer From Any Station 1) 6 : TAFAS 2 (Trunk Answer From Any Station 2) (Not assignable when the Trunk Group type is DID or PVL, or CO line access is outgoing only) incoming Mode (Night) 1 : same as Incoming Mode (Day) 2 : fixed 3 : flexible 4 : DISA (Not assignable when Trunk Group type is DID or PVL, or CO line access is outgoing only) Intercept Routing (Day) 0 : none A : transfer to the Attendant Console DN XXXX (XXXX: directory number) : transfer to an extension Intercept Routing (Night) 0: none DN XXXX (XXXX: directory number) : transfer to an extension 06 07 08 Toll Restriction Level 01 to 16 (Not assignable when CO line access is incoming only) 10 Toll Restriction Table (e for U.S.A. and Canada only) 1 to8 (Not assignable when CO line access is incoming only) 11 Dialing Plan (+ for U.S.A. and Canada on44 12 CO-CO Duration Limit 01 to 64 : minute 13 Disconnect 1 : 1.5 seconds 2 : 4.0 seconds 0 CLR 9 Time 0: none A: Type-A: 1 +NXX+NXX+XXXX NXX+XXXX B: Type-B: NPX+NXX+XXXX NNX+XXXX C: Type-C: 1 +NPX+NXX+XXXX 1 +NNX+XXXX NXX+XXXX 1 +NXX+NXX+XXXX D: Type-D: NXX+NXX+XXXX NXX+XXXX (N:2 tog, P:O,l, X:Oto9) (Not assignable when CO line access is incoming only) Continue 1 o-c-29 (60395) Page . 1 O-C-67 41 .OO DISA Code (DIC) ................................................................................... 1 O-C-68 42.00 DISA Password (DIP) ............................................................................ 1 O-C-69 43.00 DID (DID) ............................................................................................... ii-:-;; 44.00 U C D 1 (UCl) ......................................................................................... - 45.00 UCD 2 (UC2) ......................................................................................... 1 O-C-72 46.00 Information (INF) .................................................................................... 1 o-c-73 47.00 Power Failure Transfer (PFT) ................................................................ 10-c-74 48.00 Change Password (CHG) ...................................................................... 1 o-c-75 49.00 CPC Signal Detect Timing-Outgoing CO Calls (CPC) ........................... 1 O-C-76 50.00 Automatic Busy-Out Count (ABC) ......................................................... 1 o-c-77 51 .OO World Select 1 (WSl) ............................................................................ 10-c-77 (1) Interdigit Pause ................................................................................ 10-c-77 ( 2 ) Pulse Type.. ..................................................................................... 10-c-77 ( 3 ) Automatic Redial Retry Count.. ....................................................... iE:-g ( 4 ) Automatic Redial Retry Interval.. ...................................................... ( 5 ) % Break Detect (SLT). ..................................................................... 10-c-77 (6) Flash Detect (SLT) ........................................................................... 10-c-77 (7) Flash Detect (TIE) ........................................................................... 10-C-77’ ( 8 ) Answer Decision Timer.. .................................................................. 1 o-c-79 52.00 World Select 2 (WS2) ............................................................................ 10-c-79 (1) First Dial Timer ............................................................................... irE-;i ( 2 ) First Dial Timer (DID). ...................................................................... - (3) EQU Access .................................................................................... 1 O-c-79 ( 4 ) O C C Access .................................................................................... 1 O-c-79 (5) Outgoing CO Back Tone .................................................................. 1 O-c-79 (6) L-COT Busy Out Looprelay ............................................................. 10-c-79 (7) G-COT Busy Out Looprelay ............................................................ :$7$ ( 8 ) Pay Tone Frequency.. ...................................................................... - (9) Pay Tone Gain ................................................................................. 10-C-81 53.00 World Select 3 (WS3) ............................................................................ 1 O-C-81 (1) DIL 1:N CO Key Only (PITS only) ................................................... itO-8i ( 2 ) EXT Off-hook BLF (PITS only) ........................................................ (3) DTMF-Tone Integration ................................................................... 10-C-82 ( 4 ) SLT On-hook Operation Mode.. ....................................................... 10-C-82-1 ( 5 ) M o d e Selection of Calls Arriving at ATT.. ........................................ 1 O-C-82-l (6) Centrex ARS .................................................................................... 10-C-82-1 ( 7 ) Waiting for Second Dial Tone M o d e ................................................ ....................... ~6-~-~~-~ ( 8 ) Polarity Reversal Mode (Not available in your area) . . . . . . . . . . . . . . . . ( 9 ) */# Allow M o d e . . . . . ........................................................... (10) Message Waiting Lamp Off Control - Voice Mail.. ...................... :. 1 O-C-82-2 itE-8$: (11) p law - A law (E-l only) (Not available in your area). ..................... - (12) SLT Transfer Operation .................................................................. 1 O-C-82-2 (13) Ringback Tone While Transfer ....................................................... 1 O-C-83 54.00 Voice Mail Directory number (VMD) ...................................................... 1 O-C-86 ........................................................ 55.00 Mailbox Number (MBN) ................. 10-2 (70695)M 15.00 Trunk Group 2 (TG2) Description This is the second block to assign various data for trunk groups. (Password level: Two or higher) Input Format index Number index Number 01 to 16 Explanation Trunk group number Input Value for Item Number :em 3lxntef 01 Assigning Items Destination (DIL 1: N Only) I X (X : 1 to 8): ICM group number P XX (XX : 01 to 32) : pickup group number DN XXXX (XXXX : three or four digits): extension number 0: none (Assignable only when “Incoming Mode (Day)” is set to DIL1:N) DID Digit Modification Table 1 to 4 : table number (Assignable when the Trunk Group type is DID) to 08 09 CLR Input Value 10 PBX Access Code to (No Restriction) 17 Maximum three digit numbers (Assignable when the Trunk Group type is PBX, and line access is both way) 18 PBX Access Code to (Restriction) 25 Maximum three digits of numbers (Assignable when the Trunk Group type is PBX, and CO line access is both way) 26 01 to 32: maximum dialing digits 00: cannot dial after external feature access Max. Dial No. after EFA Signal 27 CO-TIE Restriction Y : CO-TIE connection is restricted N : CO-TIE connection is allowed 28 TIE-CO Restriction Y : TIE-CO connection is restricted N : TIE-CO connection is allowed 1 o-c-31 (70695) CO 0 0 A. Introduction This section provides system programming using Dumb type terminal. Before starting system programming, Section 8 “Preparation for Programming and Maintenance (Dumb Type Terminal)” must be read. This section describes the basic operations for programming. Programming mode consists of a variety of commands, which enable users to assign or change various parameters concerning the system administration such as Tenant, Class of Service, Numbering Plan and so on. A list of all programming commands is provided on the following page. 1 O-A-1 (70695) Continued _~~ - WS3 (World Select 3) 2 - CAI (CO Access Instantly) 2 _ - ACV (Account Code Verified) 2 , --- ACL (Account Code Entry on Long 2 Distance Calls) - - - SPB (Speed Dialing Boundary) 2 - - - NAG (Night Answer Group) 2 - - - PRD (Polarity Reversal Detection) 2 ?--\ VMD (Voice Mail DN) 2 These programs must be done in order from “First Ser ‘Second Ser to Third Set” shown in the table. For example, if you program Operation (OPE) before doing System Assignment (SYA) program, an error message appears. I , - - CLK CLP - - TRR -7 TDM (Clock Mode) (Clock Priority) (TIE Trunk Relay Restriction) (Tone Detection Mode 2 2 2 2 t 1 O-B-2 (70696)M Continued Item Assigning Number I 0 8 ~% Break 09 Items Input Value 1 : 60% break 2 : 67% break (Not assignable when the dial type is DTMF) 00: none 01 : 6.5 ms detection 02 to 75 : 8N ms detection (Not assignable when the Trunk Group type is DID or TIE) CPC Detection 10 1 : immediate start 2 : delayed wink start (Assignable when the Trunk Group type is DID or TIE) Start Arrangement 11 1 : 64ms 2 : 128ms Wink Signal Time-Out . . . 127 : 8.128 s Conditions Before setting this screen, “Trunk Group (TGl) (TG2)” must be programmed. This cannot be programmed if no CO trunk card is assigned in “Slot Assignment (SLA).” If any one of the cards is programmed, this screen can be programmed. If the “Trunk Group (TGl)” containing .the CO line has “Type” assigned to ‘6 (DID),” or ‘7 (TIE)” the following items cannot be entered : ” l ** ” is displayed-: l l l Direct Termination Night Answer Point (Type : No) CPC Detection If the Trunk Group (TGl)” containing the CO line has “Type” assigned to anything other than ‘6 (DID),” or ‘7 (TIE)“. the following items cannot be entered : ” l ** ” is displayed : l Start Arrangement l Wink Signal Time-Out Item Number 03 Direct Termination This is assignable only when the Trunk Group (TGl)” containing the CO line has ‘Incoming Mode (Day)” assigned to “2 (DIL l:l).” Otherwise, “+** I) is displayed and setting is impossible. 04 Night Answer Point (Type : No.) This is assignable only when the “Trunk Group (TGl)” containing the CO line has ‘Incoming Mode (Nightr assigned to “2 (Fixed)” or 3 (Flexible).” Otherwise, U *+* n is displayed and setting is impossible. ‘N (NAG)” can be selected only when Trunk Group ‘Incoming Mode (Night) is assigned to ‘2 (Fixed).” 05 Dial Type If “Pulse mode” is selected, refer to Section 10-C-51 .OO “World Select 1 (WSl)” about the following items: l Interdigit Pause l Pulse Type l % Break Detect lo-C-35 (70695) . 2.00 Slot Assignment (SLA) Description To assign the type of card equipped in each free slot on the basic and expansion shelves. (Password level : One) Input Format * In the AT mode, to display or edit in the conversation style, do not enter the index number : When you enter; PRGSLA AT (* ), the display starts from the slot number 101 and moves one by one. Index Number index Number Explanation XXX - slot (01 to 15) T shelf (1 to 3) . Physical number (101 to 315) . Input Value for Item Number tern AmIter 1 Assigning I terns Card Type Input Value XX (00 to 18) (Version 12.xX) 00: none 01 : PLC (Proprietary Integrated Telephone System Line Circuit card 02 : HLC (Hybrid Line Circuit) card 03 : SLC (Single Line Telephone Circuit) card 04 : MSLC(SLC with Message Waiting) card 06 : LCOT (Loop Start Central Office Trunk) card 07 : GCOT (Ground Start Central Office Trunk) card 08 : DID (Direct inward Dialing) card 10 : T-l (Tl DIGITAL TRUNK CARD) 12 : AGC (Automatic Gain Control) card 13 : DISA (Direct Inward System Access) card 14 : OPX (Off Premise Extension) card Continued 1 O-c-2 (70695)M 51.00 World Select 1 (WSl) Description “WSI” command provides the following assignments. (Password level: Two or higher) (1) Interdigit Pause (For Dial Pulse Trunk) Interdigit Pause is used to distinguish between pulse signals. To meet the requirements of your central office, select the appropriate value that represents the delay between dial pulses.This setting is only required when using dial pulse trunks. (2) Pulse Type (For Dial Pulse Trunk) The system supports the following three types of dial pulse signaling. Select the appropriate option to your area.This setting is only required when using dial pulse trunks. (3) Automatic Redial Retry Count Used to set the number of times Automatic Redial is tried. Automatic redialing of the last dialed number is done up to the specified number of times. (4) Automatic Redial Retry Interval Used to set the interval time between Automatic Redial RediaT” for further information. attemptsRefer to Section 4-C-4.04 “Automatic (5) % Break Detect (SLT) Dialed digits from dial pulse type Single Line Telephone (SLT) is transmitted to the system by making and breaking a loop current (dc path), therebyinterrupting loop Current-Duration time required to detect the number of breaks’depends on the SLT connected and can be administered to “16 to 96 ms” or “16 to 136 ms” by this command. (6) .Flash Detect (SLT) It is assignable that the Flash signal transmitted from SLT is detected or not by the system.lf selected, the system does not detect the Flash signal transmitted from SLT. (7) Flash Detect (TIE) Assigns the length of the flash time which applies to calls on TIE trunks. This is the time the system needs to detect the flash signal sent from the other Network. Duration time required is determined by the other PBXs. PBX of a TIE Line (8) Answer Decision Timer This entry applies to calls on TIE trunks. This is the time the system needs to recognize the off-hook signal sent from the other connecting the voice path. The entry is entered in 32 ms increments. Input Format Index Number None lo-C-77 (70695) “O=No” is PBX before When deleting or changing the pre-assigned card type, the conditions should be the followings: l The card status is OUS or Fault. l All of the port data has been deleted. However, if there exist port data, it is possible to change the cards as follows: l PLC card MHLC card l SLC card MHLC card Deleting the ATLC card will be an error if there exist the following assignments: l ‘Trunk Group (TGl)“. Incoming Mode (Day) is set to ‘7 (ATT).” Intercept Routing (Day) is set to “A (ATT).” * l “Doorphone (DPH)“, Doorphone Assignment is set to “A(AlT).” Deleting the DISA l “Trunk Group Incoming Incoming card will be an error if there exist the following assignments: (TGl)“, Mode (Day) is set to “4 (DISA).” Mode (Night) is set to “4 (DISA).” Deleting the HLC, SLC, LCOT or GCOT card will be an error if there is the following assignment to the slot to be deleted: l “Power Failure Transfer (Pmjn See Section 1 -A-5.00 “Service Cards Description” for installing the cards in combination. lo-c-4 (70695) 52.00 World Select 2 (VVS2) Description “WS2” command provides the following assignments. (Password level: Two or higher) (1) First Dial Timer On outgoing CO calls, the system waits at least 0.5 seconds after seizing the CO line, before sending the dialing digits required by the central office. This allows the central office enough time to accept the dialing digits correctly. Default setting is 1 .O second and can be ranged from 0.5 to 8.0 seconds. (2) First Dial Timer (DID) Available when “Type” of a Trunk Group is set to “DID” or “TIE”. (3) EQU Access Used to activate or deactivate the EQU Access feature on a system-wide basis. If “N” is selected by this command, programming screen of “Special Carrier Access” Equal Access is not accessible. (4) OCC Access Used to activate or deactivate the OCC Access feature on a system-wide basis. If “N” is selected by this command, programming screen of ‘Special Carrier Access” OCC Access is not accessible. (5) Outgoing CO Back Tone On outgoing CO calls, dialed number is toned out, which informs the extension users that dialed number has been dialed. CO Dialing Tone is usually toned out by default setting, select ‘N” to turn off the CO dialing tone. (6) L-COT Busy Out Looprelay, When CO line is busied out either manually by the operator or automatically by the system, the state of Loop Relay is controlled by this setting. (7) G-COT Busy Out Looprelay When CO line is busied out either manually by the Operator 1, or automatically by the system, the state of Loop Relay and Ring-FG are controlled by this setting. Input Format Index Number None 1 o-c-79 (70695)M 4.00 Operation (OPR) Description To assign data common to the whole system, by using indexes 1 and 2. (Password level : Two or higher) input Format Index Number Index Number Explanation The first Operation block 1 Input Value for Item Number Input Value Y : Tenant Service is available N : Tenant Service is unavailable I I I 02 Automatic Route Selection Y : Automatic Route Selection is available N : Automatic Route Selection is unavailable 03 Numbering Plan 1 : Flex 2 : Fixed 1 3: Fiied2 Privacy on DN Key 1 : privacy enabled 2 : privacy disabled 04 I 01 to 16 : the restriction level for telephone company operator call i 01 to 16 : the restriction level for international call Continued 10-C-6 (70695)M 53.00 World Select 3 (WS3) Description “WS3” command provides the following assignments. (Password level: Two or higher) (1) DIL 1: N CO Key Only (PITS only) It is programmable that an incoming CO call routed via “DIL 1: N” feature arrives at “CO button only” or “CO button or PDN button” as follows. (Parameters) Y : An incoming CO call routed via DIL 1: N feature only arrives at a PITS telephone which has associated CO button (SCO, GCO). If no CO button is assigned on a PITS, an incoming CO call will not arrive at that extension. N : An incoming CO call routed via DIL 1: N feature arrives at CO button (SCO, GCO) or PDN button. If no CO button is available on a PITS, an incoming CO call will arrive at PDN button available. (default) (2) EXT Off-hook BLF (PITS only) The status indicator on DSS (DNj button reflects the idle/busy status of the associated extension user under one of the following settings. (Parameters) Y : The status indicator on DSS (DN) button is lighted steadily either when. the associated extension user goes off-hook, or when all PDN buttons are busy. (default) N : The status indicator on DSS (DN) button is lighted steadily only when all PDN buttons on the associated extension are busy. (3) DTMF-Tone Integration On extensions with the Voice Mail Port parameter enabled, the KX-T336 system can send codes (DTMF tones) to indicate the state of the call (busy, answered, ringing, disconnect, etc.) in addition to the normal call progress tones. These codes enable the Voice Processing system to immediately recognize the current state of the call and improve its call handling performance. (Parameters) Y : The KX-T336 system sends codes (DTMF tones) to the VPS. N : The KX-T336 system does not send codes (DTMF tones) to the VPS. (default) 10-C-81 (70695) 6.00 System Timer (TIM) Description To assign a value to the various system timers. (Password level: Two or higher) Input Format piiq pq (~I)))] Input Value for Item Number tern Uumber Input Value Assigning Items 01 Held Call Reminder 15to240: 02 Held Call Reminder (ATT) 15to240 : s 03 Transfer 15to240: 04 Pickup Dial Waiting 1 to 5 05 External First Digit Time-Out 5 to 120 : s 06 External Inter digit Time-Out 3 to 15 07 External Inter digit Time-Out PW 3 to 10 - : s 08 Toll Restriction Guard Timeout 0 to 25 : s 09 Call Forwarding-No Answer Time-Out 5to60 : s 10 Intercept Routing Time-Out (System) 5to240 : s 11 Intercept Routing Time-Out (DISA) 5to240 : 12 Attendant Overflow Time 5to240 13 SMDR Duration Time oto15 : 14 TIE Interdigit Time-Out 3to30 : s Recall s s : s :. s s : s s Conditions Item Number 01 to 02 Held Call Reminder/ Held Call Reminder (ATT) If these items are programmed but if “Operation (OPR)” Index Number 1, Held Call Reminder is set to ‘N,” Held Call Reminder does not function. lo-C-74 (70695)M (5) Mode Selection of Calls Arriving at ATT When two attendant consoles are connected to the system, one of the following three types of Incoming Mode can be selected. Options 2 and 3 work only for the incoming outside call routed via a CO line which belongs to the Trunk Group whose Incoming Mode (Day) is assigned as “ATT.” (Parameters) 1. Load Sharing Incoming outside calls are distributed evenly to two attendant consoles so that they can share the same load. (default) . 2. Simultaneous Ringing An incoming outside call rings at two attendant consoles simultaneously. 3. Interconsole IRNA If an incoming outside call ringing at one attendant console is not answered within a specified time period (Attendant Overflow Time), it will be automatically transferred to another attendant console automatically. (6) Centrex ARS Mode In ARS mode, not only a 7-digit or 1 O-digit number but a number equal to or less than g-digit (such as CENTREX feature access code) that follow the ARS access code (default: 9) can be routed via an outside line. A number equal to or less than 6-digit is routed via Local Trunk Dial Access procedure after passing toll restriction process. A 7-digit or IO-digit number is routed via ARS procedure after passing toll restriction process. (Parameters) Y : A number equal to or less than 6-digit can be routed via an outside line in ARS mode. N : A number equal to or less than 6-digit can not be routed via an outside line in ARS mode. (default) (7) Waiting for Second Dial Tone Mode In some area, upon completion of facility access code entry, the extension user must ensure the reception of the second dial tone from the Central Office before continuing to dial the telephone number. (Parameters) Y : The system waits for the second CO dial tone. N : The system does not wait for the second CO dial tone. (default) (8) Polarity Reversal Mode - (Not available in your area.) (9) */# Allow Mode Used to determine if the dialed ‘jt” and/or “#” in the leading 3 digits will be checked by Toll Restriction. This assignment is required for certain central offices (CO) to prevent toll fraud. Some CO ignore the user-dialed ” jc” and/or %.” If your CO is such a type, select ‘N” (Restricted). (Parameters) Y : Not restricted N : Restricted (default) 1 o-C-82-l (70695)(E)M Continued Item Number Assigning Items Input Value CLR 048 Call 049 Do Not Disturb Set 0 0 Call Forwarding/Do Not Disturb Cancel 0 051 Dial Call Pickup Deny Set 052 . Dial Call Pickup Deny Cancel Forwarding-Busy/No Answer 059 Data Line Security Set 0 0 0 0 0 0 0 0 0 060 Data Line Security Cancel 9 Call Waiting Set Maximum four digits consisting of numbers, * , # Call Waiting Cancel BSSIOHCA Deny Set BSS/OHCA Deny Cancel Busy Override Deny Set Busy Override Deny Cancel 061 Pickup Dialing Programming Maximum four digits consisting of numbers, * Maximum four digits consisting of numbers, * , # Pickup Dialing Set 063’ Pickup Dialing Cancel Absent Message Set 1 0 0 0 0 Station Lock Cancel Continued Assigning 01 Items Input Value DIL 1: N CO Key Only Y: Arrives at CO button only N: Arrives at CO button or PDN button . (Default = N) 02 Y: DSS indicator lights when all PDN buttons of the associated extension are busy or Off-Hook N : DSS indicator lights only when all PDN buttons of the associated extension are busy EXT Off-hook BLF (Default = Y) 03 Y: The KX-T336 system sends codes (DTMF tones) to the VPS. N : The KX-T336 system does not send codes (DTMF tones) to the VPS. DTMF-Tone Integration (Default = N) 04 SLT On-hook Operation mode 1 : Hang-up causes ringing of consultation hold recall tone. 2 : Hang-up disconnects a call on consultationhold. (Default = 1) 05 Mode Selection of Calls Arriving at A7T 1 : Load Sharing 2 : Simultaneous Ringing 3 : Interconsole IRNA (Default = 1) 06 Centrex ARS Mode Y: A number equal to or less than 6-digit can be routed via an outside line in ARS mode. N : A number equal to or less than 6-digit can not be routed via an outside line in ARS mode. (Default = N) 07 Waiting for Second Dial Tone Y: The system waits for the second CO dial tone. N : The system does not wait for the second CO dial tone. (Default = N) 1 O-C-82-3 (70695)M Continued Item NUlllbH Assigning 106 Call Forwarding-Follow Me Set 107 Call Forwarding-Follow Me Cancel 108 Other PBX Extension 01 109 Other PBX Extension 02 110 Other PBX Extension 03 117 Other PBX Extension 04 CLR Input Value items Maximum four digits consisting of numbers, *, # 0 0 0 0 0 0 One or two numeric digits . - 124 Transfer 125 Conference Maximum four digits consisting of numbers, * , # 0 0 0 : clearing function is effective for the item 10-c-23-1 (70695) 54.00 Voice Mail Directory Number (VMD) Description Used to assign DN of a Voice Mail port (the extension port to which the Voice Mail system is connected.) This means the KX-T336 system will send the mailbox number of the extension (on which a call forwarding feature is assigned) with DTMF tones to a Voice Mail port, when a call forwarded to a Voice Mail port is answered. Calls from any Voice Mail port will not be forwarded, if forwarding destination is another Voice Mail port. Input Format Index Number None Input Value for Item Number kfn Number 01 . Input Value Assigning Items Voice Mail DN 1; DNxxxx: Directory Number 0: None (Default = 0) Programming (Example) When DN 109 to 112 are connected to the Voice Mail ports. To assign the Voice Mail DN 1. At the programming prompt (PRG>),‘type: + ; PRG>VMD AT 01 (J ) The screen displays the Input prompt (INPUT ; PRG> VMD AT 01 ; 01: Voice Mail DN . . . . . . . . . . . . . . . . 0 INPUT >> +: >a) as follows: 2. At Input prompt (INPUT >>), type: ; PRG> VMD AT 01 ; 01: Voice Mail DN . . . . . . . . . . . . . . . . 0 ( J) INPUT >> DN109 +; The screen displays the next Input prompt (INPUT B) as follows: ; PRG> VMD AT 01 ; 01: Voice Mail DN . . . . . . . ..-... 0 . INPUT >> DN109 i 02: Voice Mail DN . . . . . . . . . . . . . . . . 0 INPUT >> +; 1 O-C-83 (21292) Conditions “Numbering Plan (NBP)” setting cannot be changed if =Operation (OPFt)” index 1, Numbering Plan is set to “2 (Fixed 1)” or “3 (Fixed 2).” If ‘1” is selected, this setting is changeable. Logical check is performed by every storage according to the following logic: . Extension numbers are three or four digits and the leading one or two digits are assigned in this screen. Feature numbers may be one, two, three or four digits. Those numbers assigned in this screen cannot include the same number For example, the assigned to other feature number as the part or whole of it. digit “2” is assigned to the feature number for “Trunk Group 01-08 Access” and another digits “21” is assigned for “Trunk Group 09-19 Access,” it is checked at the time of data storage. Similarly, ‘36” and ‘351” cannot be present at the same time. It is. possible to store ‘0” through ‘9,” =*, n “#,” as the feature numbers. However, if U*” or ‘#” is included in the feature numbers, those features are not accessed by the rotary telephone extensions. Item Number 01 to 16 108 to 123 1st to 16th Hundred Block Extension Other PBX Extension 01 to 16 Extension numbers cannot include “*” and %.” 63.00 Equal Access Code (EQC) (+ for U.S.A. and Canada only) Description Either ‘1OXXx” or ‘101 XXXX” can be selected as Equal Access Code. (Password Level : Two or higher) Refer to Section 1 O-H-l .OO “Equal Access” for further information. input Format Index Number None Input Value 1: 1 OXXX (default) 2: 101XXXX 10-C-l 08 (~95) 14.00 Trunk Group 1 (TGI) Description To assign information for the 16 trunk groups. This is the first of two blocks. (Password level: Two or higher) input Format Index Number Index Number 01 to 16 Explanation Trunk group number Input Value for Item Number m rmber Assigning Items Input Value 01 We 1 : DDD(Direct Distance Dialing) 2 : FEX(Foreign Exchange) 3 : WATS (Wide Area Telecommunication Service) 4 : PVL (Private Line) . 5 : PBX (Behind PBX) 6 : DID (Direct Inward Dialing) 7 : TIE (TIE Line) 02 Name Trunk group name Maximum three digits composed of characters, numbers, and marks (Enclose the name with double quotes “.) 03 Tenant l/2: tenant number (not assignable when “Tenant Service” is set to .Na) 04 Incoming/Outgoing 1 : incoming only 2 : outgoing only 3 : bothway CLR 0 Continued 1 O-C-28 (70695) item Number Assigning items input Value 15 Channel No. 12 0: none 19 Channel No. 1 6 (DefaukO) 20 Channel No. 1 7 21 Channel No. 1 8 22 Channel No. 19 23 Channel No. 20 24 Channel No. 21 I [Note] ’ * + * scI will be displayed in the item numbers 28 through 35. These items cannot be assigned. 1 25 1 Channel No. 22 1 26 1 Channel No. 23 27 Channel No. 24 28 Channel No. 25 29 Channel No. 2 6 30 Channel No. 2 7 31 Channel No. 2 8 32 Channel No. 2 9 33 Channel No. 3 0 34 Channel No. 3 1 35 Channel No. 3 2 . Not assignable ” lo-c-110 (70695)M Continued item Number Assigning Items input Value 14 Pause Time 1 2 3 4 : : : : 15 Hook Switch Flash Time 0: 1: 2: 3: 4: 5: CLR 1.5s 2.5 s 3.5 s 4.5 s none 80ms 300 ms 600ms 900 ms 1200ms 0 : clearing function is effective for the item Conditions The assigning items:Type, Incoming Mode (Day/Night), Destination (OIL 1:N Only) and Type and Number can be changed only when all the trunks belonging to the trunk group are not in use. If any trunk is used, it is impossible to change. Item Number 03 Tenant If I*** m is displayed here, “Operation (OPR)“; Tenant Service is set to “N (No).” 04 Incoming/Outgoing When “Incoming Only” is selected in the trunk group with DID, the following items are assignable but they do not work at all in Incoming Only mode. l Disconnect Time l Pause Time l Hook Switch Flash Time l Max. Dial No. after EFA Signal For further information, refer to “3. Other Conditions” on page 9-E-7. 05 Incoming Mode (Day) Refer to Section 9-E-l -01 Trunk Group (l/2).” 06 Incoming Mode (Night) If ‘2 (Fixed)” or 3 (Flexible)” is changed to another option, it cancels all the settings of CO lines in “CO Line (COL)“, Night Answer Point (Type: No.) which belong to the trunk group. If “2 (Fixed)” is changed to 3 (Flexible)” and vice versa, the Night Answer Points are not canceled. 11 Dialing Plan Refer to Section 9-E-l .Ol “Trunk Group (l/2).” For the relation between trunk group/CO line setting and PITS refer to Section 9-E-l .Ol Trunk Group (l/2).” 10-c-30 (70695)(F) ON button setting, 64.03 Master Clock Priority (CLP) - T-l Description Used to decide to which external clock pulse the system synchronizes, when multiple T-l cards are installed. (Password level : Two or higher) Input Format Index Number None Input Value for Item Number Item Number 1 to 6 Assigning Items Priority 1 to 6 Input Value T-l card physical slot number (three digits number) (Default = None) Note: You have to assign this item even if only one T-l card is installed. l Conditions When more than two T-l cards are installed in the system, each of them should be registered by this command. .. l&c-112 (70695)M I tern Assigning Items r Jumber 29 TIE Forced Account mode CLR Input Value Y N : TIE callers are required to enter account code when making CO calls. : Entering account code is not required. 30 TIE Incoming Delete Digit 0 : deleting no digits 1 to 4 : number of deleting digit(s) 31 blank : Inserting no digit A maximum of four digits number composed of 0 through 9 can be entered. TIE Incoming Insert Dial 0 Conditions Refer to Section 10-C-14.00 “Trunk Group 1 (TGl).” 10-C-31-1 (70695) : clearing function is effective for the item 65.00 TIE Line Related Commands 65.01 TIE Line Routing Table (TIE) Description Used to determine the routing of calls over the TIE Line Network Up to 36 routing patterns can be programmed by this command. Routing table is referenced by the system to identify the trunk route, when a TIE call is made by dialing the feature number for “TIE Trunk Access.” (Password level: Two or higher) input Format Index Number Explanation Index Number TIE Line Routing Table number 01 to 36 Input Value for Item Number Item Nurber Assigning 1 Items Input Value Up to three digits : 0 - 9, X (wild card) Code 1 (Default = blank) I 0 to 4 : number of deleting digit(s) I 1 2 1 Delete digit I I 3 (Default = 0) Up to four digits : dialing number to be added- Insert Dial . (Default = blank) 4 Trunk Group Hunt Sequence 01 01 to 16 : trunk group number whose type is set to TIE. 5 Trunk Group Hunt Sequence 02 (Default = blank) 6 Trunk Group Hunt Sequence 03 7 Trunk Group Hunt Sequence 04 8 1 Trunk Group Hunt Sequence 05 1 10-c-120 (70696) I 18.00 CO Line (COL) Description To assign parameters on a CO line basis. DATA ERROR appears on the entry of parameters if no trunk card is assigned in the Slot Assignment (SLA) programming. (Password level : Three or higher) Input Format Index Number index Number Four digit numbers (1011 to 3158) Explanation Physical number of the CO line input Value for item Number em Assigning lumber 01 Trunk Group Items Input Value 01 to 16 : trunk group number 02 Trunk Name Maximum ten digits consisting of letters, numbers and marks (Enclose the name with double quotes ‘.) 03 Direct DN XXXX (XXXX : three or four digits) : extension number 0 : none (Not assignable when the Trunk Group type is DID, PVL or TIE, or Incoming Mode (Day) is set to any mode except DIL 1:l) 04 Night Answer Point (Type : No.) 05 Dial Mode 1 : DTMF mode 2 : Pulse mode 3 : MFC-R2 mode 06 DTMF Duration Time 1 : 80ms 2 : 160ms (Not assignable when the dial type is pulse) 07 Pulse Speed Termination DN XXXX (XXXX : three or four digits) : extension number Ul : universal night answer 1 U2: universal night answer 2 0 : none R : Remote Administration N : Night Answer Group Extensions (Not assignable in case of DID, TIE, or PVL, or outgoing only) 1 : low (10 pps) 2 : high (20 pps) (Not assignable when the dial type is DTMF) Continued 10-c-34 (70695) 65.03 TIE Trunk Relay Restriction (TRR) Description Used to allow or restrict the TIE trunk relay function on the trunk group basis. Refer to Section 3-F-l 4.04 ‘Alternate Routing” for further information. (Password level: Two or higher) Input Format Index Number Explanation Index Number Trunk Group Number (Call receiver side) 01 to 16 Input Value for Item Number Item Number None Assigning Trunk Group Number (Call initiator side) . Items Input Value Y : Restricted N : Allowed (Default = N) Conditions TRR command is valid for the trunk group whose type is set to TIE. Programming example TIE Trunk Relay Restriction settitig In this case, if you want to restrict ‘TIE call relay from TGlO to TGl 1’ program as follows: ;PRG>TRRATlOll (J) ; Trunk Group No.1 0 ; 11 : Trunk Group No.1 1 . . . . N ; INPUT >> Y (J) 50.00 Automatic Busy-out Count (ABC) Description It is administrable to busy out the invalid CO line automatically to prevent extension users from accessing it by monitoring the loop current sent through CO line. (Password level: Three or higher). One of the following three options is assignable on a CO line basis. (1) N=O On CO calls, the system monitors a loop current sent through the CO line, and if a loop current is not detected, busy tone is sent to the caller. (2j N=l to 240 On CO calls, the system monitors a loop current sent through the CO line, and if a loop current is not detected pre-assigned times (1 to 240) consecutively, busy tone is sent to the caller. Then the system busies out the corresponding CO line automatically. (3) N=241 On CO calls, the system does not monitor the loop current sent through the CO line, iherefore, CO line is always seized by extension users whether loop current is running or not. Refer to Section 52.00 rNS 2” L-COT/G-COT Busy Out Looprelay. Input Format . Index Number I I Index Number II Explanation 1011 to3166 1 Physical Number of the Trunk Port Input Value for Item Number tern Jumber None Assigning Items Automatic Busy-out Count Input Value xxx(oto241) (Loop Current Detection) 0: Yes 1 to240: Yes 241 : (Default = 241) 10-C-76 No (Automatic Busy-out) No Yes if loop current is not detected by the preassigned times (1 to 240) No I I 67.00 DISNAGC Tone Detection Mode (TDM) Description When Tone Detection for DISA/AGC is set to”Yes”, the system disconnects the lines if it detects any tones, regardless of tone type, during a trunk-totrunk call (DISA or AGC). This command is used to select a type of tones which applies to tone detection for DISAIAGC on a Trunk Group basis. For example, if “2:cyclic tone only” is selected, the system disconnects the lines only when it detects cyclic tone durina a trunk-to-trunk call (DISA or AGC). (Password level : Two or higher) Input Format Index Number Index Number Explanation 01 to 16 Trunk Group Number Input Value for it&m Number Item Assigning Items Number I None To’ne Detection Mode (DISAIAGC) Input Value 0: all tones (no tone, cyclic tone, continuous tone) 1: no tone or cyclic tone 2: cyclic tone only (Default = 0) Conditions None . lo-c-130 (70695) Input Value for item Number &In Assigning lumber 1 lnterdigit Input Value items Pause 1 : 630 ms 2:830ms 3: 1030ms (Default=2) 2 Pulse Type 1 : Normal 2 : New Zealand 3 : Sweden (Default=l) 3 Automatic Redial Retry Count 01 : 1 time . . 3; : 32 times (Default=1 5) 4 Automatic Redial Retry Interval 01 : 10s . . 3;:32Os (DefauMI4) 5 % Break Detect 1 : 16to96ms 2:16to136ms (Default = 1) 6 Flash Detect (SLT) 0 : No 1 : Yes (Default = 1) 7 Flash Detect (Tie) 0 : Disabled (no detection) (2OOms- : On-hook) 1 :200mstol s ( l s - : O n - h o o k ) 2:8Omstois(ls-:On-hook) 3 : 200 ms to 1.5 s (1.5 s - : On-hook) 4:80msto1.5s(1.5s-:On-hook) (Default = 1) 8 Answer Decision Timer 001: 32 ms 002:64ms . . 2;5: 8.16s (Default = 001) 1 O-C-78 (70695pl . 69.00 Limited Call Duration (LCD) Description Used to set parameters on “Limited Call Duration” feature. This feature can be enabled or disabled on a COS basis. For further information, refer to Section 3-F-l 6.00 “Limited Call Duration”. (Password level : Two or higher) Input Format Index Number Index Number Explanation 01 to32 COS (Class of Service) number Input Value for Item Number Item Assigning Items. Number 1 Extension-CO call duration time Input Value 00: No Limitation 01-60: Limitation Time (Minutes) (Default=OO) 2 Call type 0: Outgoing CO call only 1: Incoming CO call onty 2: Both (DefaulkO) . l&C-132 mw input Value for Item Number tem Vumber 1 Assigning items Input Value First Dial Timer 01 : 0.5 s 02: 1.0s . lb8.0~ (Default=02) 2 First Dial Timer (DID) . 001 : 32 ms 002:64(32X2)ms 2;5 : 8.16 (32X255) s (Default=002) 3 EQU Access Y: EQU Access is allowed N : EQU Access is not allowed (Default = Y) OCC Access 4 Y : OCC Access is allowed N : OCC Access is not allowed (Default = Y) 5 Outgoing CO Back ione Y : Dialed digits is toned out N : Dialed digits is not toned out (Default =-Y) 6 L-COT Busy Out Looprelay Y : Loop Relay ON N : Loop Relay OFF (Default = N) 7 G-COT Busy Out Looprelay 1 : Loop Relay ON + Ring-FG Open 2 : Loop Relay OFF + Ring-FG Close 3 : Loop Relay OFF + Ring-FG Open (Default = 3) 1 O-C-80 (70695)M r:ORNo. .. I Cancel the storage as an overflow destination. 396 Attempting to delete the extension/RMT which is registered as a DIL 1 :l call destination of CO line. Cancel the storage as a DIL 1:l call destination. 397 Attempting to delete the extension which is registered as a night answer point of CO line. Cancel the storage as a night answer point. 398 Attempting to delete the extension which is registered as a walking station. Cancel the storage as a walking station. 399 Attempting to delete the PITS paired with DSSconsole. Change the PITS paired with DSS Console. 400 Attempting to delete the extension which is registered as a night answer point for tenant. Cancel the storage as night answer point. 401 Attempting to delete the extension which is set to SDN. Cancef the assignment of SDN. 403 Attempting to delete the ATT when the ATT is assigned for day incoming mode in Trunk group. Change the incoming mode destination other than AI-T. 404 Attempting to delete RMT when the RMT alarm is assigned. Cancel the assignment of RMT alarm. 405 Attempting to delete the external pager which is registered as UNA point for CO line. Change the night answer point. Attempting to delete the external pager which is registered as a TAFAS for day/night incoming mode for Trunk group. Change the incoming mode. Attempting to delete the external pager which is registered as a paging destination for the ATT. Change the paging destination. Attempting to delete the ATT which is specified for maintenance device. . When deleting ATT, combination of operators 1 and 2 is incorrect. ;I I ,I Countermeasure Attempting to delete the extension which is registered as an overflow extension for UCD group. I I~ Probable Cause 406 t 407 409 t409 I - I After changing maintenance device. delete Impossible to delete the card, for all of the ports belonging to the card is not made pm-installed. Delete all the ports belonging to the card. 412 Impossible to delete the card, for DN is assigned to an extension port. Delete all the ports belonging to the card. 413 Deleting the card is impossible, for it is assigned as a maintenance device. Change the maintenance device. 411 lo-D-4 (21292) I I (4) SLT On-hook Operation Mode In single line telephone procedures, active call is put on consultation hold when the switchhook is pressed down for approximately l/2 second and released. In this case, consultation hold recall tone will ring immediately if you replace the handset on the switchhook without dialing any digits. Then you may hear recorder tone when you lift the handset to reply this ringing This, may happen sometimes if the handset is replaced on the switchhook after hopping on it. To prevent such unexpected consultation hold tone from ringing, select for this setting. “2” When setting “Y is selected, a call put consultation hold will be disconnected if you replace the handset on the switchhook without dialing any digits. When ‘1 I is selected. - default 40 . (1) Talking Talking with a caller. 1 73 ,;, RING! , , y,RING~,+’ . . (2) Hooking A call is put on consultation hold. (3) On-hook Wtthout dialing any digits. (4) (2) Hooking Acallispliton consultation hold. (3) On-hook Without dialing any digits. (4) Disconnection A call on consultation hold is cliiconnected. Recall Consultation hold tone rings. When “Y is selected (1) Talking Talking with a caller. (Note) To hang up and make another call right away, an SLT user should hold down the switchhook for more than two seconds. be sure to (Parameters) 1 : Hang-up causes ringing of consultation hold recall tone. (default) 2 : Hang-up disconnects a call on consultation hold. 10-C-82 (30393) DATA ERROR No. Probable Cause Countermeasure 431 Attempting to remove a card which is registered in Power Failure Transfer (PFT) assignment. Cancel the PFT assignment of the card. Impossible to change the Numbering Plan to “Fixed,” because there exist DN’s which should be blank in the ‘Fixed” mode in the Hundred B l o c k . Clear DN’s which should be blank. 440 450 Impossible to change GM/Paging group, for the Change after deleting all the extensions in the pickup group belonging to the ICWaging group pickup group. contains extensions. 1 O-D-5-l (70595) . (10) Message Waiting Lamp Off-Control - Voice Mail Used to determine whether the system turns off the Message Waiting lamp or the VPS does when the VPS answers the callback from the message receiver. (Parameters) 1. Normal Mode The system turns off the Message Waiting lamp. (default) 2. Voice Mail Mode 1 Only the VPS port that turned on the Message Waiting lamp can turn it Off. 3. Voice Mail Mode 2 Any VPS port can turn off the Message Waiting lamp. (11) p -law-A-law (E-l only) - (Not available in your area.) (12) SLT Transfer Operation If set to ‘Mode Z, the following operations become available with the SLT users. l l l Screened Call Transfer to Trunk (Section 5-D-l -06) Call Transfer by using the feature number for “Transfer.” (Section 5-D-l through 1.05) Establishing a conference call by dialing the feature number for ‘Conference.” (Section 5-E-1 .OO) .Ol (Parameters) 1: Mode 1 (default) 2: Mode 2 (13) Ringback Tone While Transfer Used to select the type of sound source during an unscreened call transfer to an extension. By default, the caller hears Music on Hold (if provided) while the caller is being transferred to another letion. However, if no music source is provided with the system, the caller hears no sound. In this case, we recommend changing the setting to Y/(Ringback Tone).” (Parameters) Y : Ringback Tone N : Music on Hold (default) Input Format Index Number None 1 o-c-82-2 (70695)(E)M 3.00 Fixed Error Messages DATA ERROR No. Probable Cause Countermeasure 003 Unacceptable value is assigned. Assign an allowable value. 004 Space exists between items. Remove the space. 005 Some items are left blank. Assign all required items, or leave all items blank. 006 At least one blank should be left among multiple Leave at least one blank. items. 007 Assigned selection value is not for the item, Set the assignable value. 008 The number which is set previously in this screen is assigned again. Set the number different from the previous number. 009 The number which is set previously in a different Set the number different from the previous screen is assigned. number. 012 Device is not installed. Assign the installed device. 013 Status of the specified device does not accept this command. Change the.status of the device to be acceptable for the command. 016 Privilege level is lower than specified level. Increase the privilege level through the Change level function. 017 Diagnostic error has been detected when INS command is executed. Verify the related device. 018 Specified service is not executed. Check specified service. 019 Another maintenance device (remote, PITS, system) is in use. Wait until another device is finished or let him finish. 020 Printer is not connected to the system or the power is off. Connect the printer, and make the power on. 021 Print out is unavailable from Remote. Execute print out on-site. 022 Entered parameters for Item or Index ia out of the spepified range. Enter the parameters within the specified range. 023 ‘,I” or l , &I+ ” is entered in BT (Batch) programming. Correct the wrong entry. 024 Calendar IC malfunction. Repair calender IC. 027 Backup device is not connec$ed (only when maintenance device is ATT). Connect the backup device to SIO # 1 Port. 029 Diierent version at the time of backup. Match the backup version. 10-D-6 (21292) Itelm NUITlbS Assigning Input Value Items 08 Polarity Reversal Mode Not available in your area. 09 s+c/# Allow Mode Y : Not restricted N : Restricted (Default = N) 10 Message Waiting Lamp Off Control Voice Mail - 1 : Normal Mode 2 : Voice Mail Mode 1 3 : Voice Mail Mode 2 (Default = 1) 11 P-law-A-law (E-l only) Not available in your area. 12 SLT Transfer Operation 1 : Mode 1 2: Mode2 (Default = 1) 1 3 Ringback Tone While Transfer Y : Ringback Tone N : Music on Hold (Default = N) - , 1 o-C-82-4 (70696)(E)M Section 14 Maintenance VT220 and Compatibles F 3.06 Expansion shelf power down (DC) .............................................. 3.07 Expansion shelf power down (AC) .............................................. 3.08 Progress tone failure (TSW card). ............................................... 3.09 Check date/time (Real Time Clock IC) ........................................ 3.10 Conference trunk failure (Basic) .................................................. 3.11 Conference trunk failure (Option) ................................................ 3.12 System memory error (Major) ...................................................... 3.13 System memory error (Minor). ..................................................... 3.14 Device not connect for SMDR ..................................................... 3.15 CPU RAM backup battery down .................................................. 3.16 Card link failure (LPR) ................................................................. 3.17 LPR ROM checksum error .......................................................... 3.18 LPR RAM failure .......................................................................... 3.19 Card disconnect ........................................................................... 3.20 Modem failure (RMT card) ........................................................... 3.21 LPR memory checksum error ...................................................... 3.22 Card type error (LPR) .................................................................. 3.23 LPR runaway ............................................................................... 3.24 OGM CPU runaway (DISA) ......................................................... 3.25 OGM lost (DISA) .......................................................................... 3.26 OPX power down ......................................................................... 3.27 D T M F generator failure (COT card) ............................................ 3.28 D T M F receiver failure (SLCRILCIOPX card). .............................. 3.29 Tone detector failure (DISNAGC card) ....................................... 3.30 HDLC failure (ATLC card) ............................................................ 3.31 Port link failure (AlT/DPH) .......................................................... 3.32 OHCA SW failure(TSW card) ...................................................... 3.33 OHCA not installed (PLCIHLC) ................................................... 3.34 TSW DTMF GIR. failure ............................................................. 3.35 Digital trunk failure (out of synchronization) ................................. 3.36 Digital trunk failure (RAI signal reception) ................................... 3.37 Digital trunk failure (AIS signal reception) .................................... 3.38 Digital trunk failure (frame trouble) .............................................. 4.00 Troubleshooting via User-Reported Troubles ................ ..A .................... Page 14-E-9 14-E-1 0 14-E-11 14-E-12 14-E-1 3 14-E-14 14-E-15 1 4 - E - 1 6 14-E-17 14-E-18 14-E-19 14-E-20 14-E-21 14-E-22 14-E-23 14-E-24 14-E-25 14-E-26 14-E-27 14-E-28 14-E-29 14-E-30 14-E-31 14-E-32 14-E-33 14-E-34 14-E-35 14-E-36 14-E-37 14-E-37-1 14-E-37-2 14-E-37-3 14-E-37-4 14-E-38 Functional Test by Entering Commands .......................................................... 14-F-1 1 .OO introduction ............................................................................................ 2.00 Test Main Menu ..................................................................................... 3.00 Testing the Cards ................................................................................... 3.01 Functions to be Verified ............................................................... 3.02 Card Test Initial screen ................................................................ 14-F-1 14-F-2 14-F-3 14-F-3 14-F-4 14-2 (70695)M 64.00 T-l Related Commands 64.01 Channel Assignment (CHA) - T-l Description Assigns the type of T-l trunk interface to each channel. (Password level: One) Input Format Index Number Explanation Index Number Physical number (101,105,109,201,205,209,301,305,309) x xx -Slot No. (01 05 or 09) LShelf (1 to 3) Input Value for Item Number tern rlumber Input Value Assigning Items 01 Option 02 Frame Sequence Automatic Set 1: W-2: ESF (Defaub2) 03 Line Coding 1: B8zS 2: AMI (Default=l) 04 Channel No. 01 05 Channel No. 02 06 Channel No. 03 07 Channel NclO4 08 Channel No. 05 09 Channel No. 06 10 Channel No. 07 11 12 Channel No. 08 Channel No. 09 13 Channel No. 10 14 Channel No. 11 : 0: none 1:LCO 2: GCO 3: DID 4: OPX 5:TIE (Defautt=O) [Note] ,u* )C *. will be displayed in the item numbers 28 through 35. These items cannot be assigned. .. 10-C-109 (70695)M 3.00 Troubleshooting via Error Log Records 3.01 Error Log Record List Background Diagnostic Errors ERR CODE sever[Y 3100 3200 3300 0301 0400 0410 DSOn 051n 0600 3700 3800 38bb 9900 39tt DAZZ MJ MJ MJ MJ MJ MN MJ MN MN MN MN -- DBOO DC00 10xX 11xX 12xX 1300 13x% 14%x 20xX 21xX 22xX 50xX 51XX 6Oxx 61xx 70xX 71xX MN __ MN MJ MN MN MN MN MN MJ MN MN me MN l- AUTOMATIC FAILURE REPORT (SMDR) MESSAGE ATT TSW clock down TSW clock down Basic shelf power down Basic shelf power down Expansion shelf n (l/2) power down Expansion shelf n (l/2) power down Progress tone failure Check date/time Conference trunk failure Conference trunk failure Conference trunk failure Conference trunk failure System memory error System memory error CPU RAM backup battery down Card link failure LPR ROM checksum error LPR RAM failure Card disconnect Card disconnect Modem failure LPR memory checksum error Card type error ” LPR runaway OGM CPU runaway OGM lost OPX power down OPXpowerdown ( b e l l ) Digital trunk failure Digital trunk failure LOCAL ALARM MESSAGE PITS TSW Clock Down TSW Clock Down TSW DWN I-SW DWN B-Shetf POW Down E-Shelf POW Down E-Shelf POW Down Tone Failure Check Datemme CONF TRK Failure POW DWN POW DWN POW DWN DIAL TN CLCK IC CONF l-K CONF TRK Failure CONF lK SYS Memory Error SYS Memory Error SMDR Not Connect Battery Down Card Link Failure LPR ROM Failure LPR RAM Failure Card Disconnect Card Disconnect MODEM Failure SYS MEM ~~AEM SMDR BATTERY CRD LNK CRD ROM CRD RAM DISCNCT DISCNCT MODEM sys COMMENTS NDT overflow ;oft timer overflow ntemal clock down !xtemal clock down IC power down 4C power down IC power dowh 4C power down nil basic trunk failure ,runk failure all optional trunk failure :runk failure _ .ead error wriielread error l-SW card loaded data failure card type error LPR runaway OGM CPU runaway ’ OGM Lost OPX Power Down OPX Power Down D-Trunk Failure OGM LOS OPX POW OPX POW D-TRK D-Trunk Failure D-TRK Legend: MJ-Major Alarm MN-Minor Alarm 14-E-4 (70695)M line trouble (out of synchronization) line trouble (RAI signal reception) 64.02 System Clock Mode (CLK) -T-l Description Used to set the system clock mode to ‘External” or ‘Internal.” l l External clock mode . . . . . . The system synchronizes to a clock pulse provided by the Central Office. internal clock mode . . . . . . The system synchronizes to a clock pulse provided by the internal TSW clock. To utilize the T-l lines, the system should synchronize to a clock pulse provided by the Central Office. However, if synchronization with External clock is lost, the system automatically switches to ‘Internal clock mode.” (Password level : Two or higher) Input Format Index Number None Input Value for item Number Item * Number None Assigning Items TSW clock mode Input Value 1 : internal dock 2 : External clock (Default = 1) Note : l When utilizing the T-l lines, the clock mode cannot be changed unless all Tl DIGITAL TRUNK Cards in the sybtem turns to l OUS” or “FAULT” status. l When the external clock has problems and is not working properly, the internal clock starts F work automatically. lo-c-111 (70695)M 64.04 ESF Frame Option (EFO) - T-l Description Used to define the values of C-bit and D-bit (Password level : Two or higher) when Frame Sequence is D4/ESF in T-l interface. Input Format Index Number Explanation Index Number Slot No (01 05 or 09) =Shelf (l’to i) Physical number (101,105,109,201,205,209,301,305,309) Input Value for Item Number k%ber Assigning I None Values for k-bit and D-bii I Input Value Items 1: Option4 (C=A, D=B) 2: Option-16 (GO, D=O) 3: Optional 6 (C=l , D=O) 4: Option-16 (C=O, D=l) 5: Option-l 6 (C=l, D=l) (DefauM) . lo-c-113 (70695)M 3.03 TSW clock down (Internal/External) (1) Internal clock down Error Code 0300 Possible cause of the malfunction 1) TSW card connection error 2) TSW card clock link failure (Internal) Countermeasures 1Is the trouble registered in the Error 1 II Is an Extension/CO call possible ? I Replace the TSW card Yes I No change in condition Replace the Shelf I I Note . End I If the TSW clock malfunction occurs: 1) The attendant console does not function. (Communication to the LPR becomes impossible) 2) Calling becomes impossible 3) Power Failure Transfer will be activated 14-E-6 (70695) I OK - 3 65.02 TIE Account Code (TAC) Description TIE account codes registered by TAC command is used to prevent the tie callers from making unauthorized CO calls by checking the validity of the account code entered. TIE callers must enter a TIE Account Code to make a CO call via TIE lines, if “TIE Forced Account Code Mode” is set to ‘Yes.’ Refer to Section 3-F14.02 ‘Calling from TIE to CO” for further information. (Password level : Two or higher ) Input Format ( Item Number (01-32) ) [CR J 1 Input Value for Item Number Item Number 01 to 32 Assigning Items TIE Account Code Input Value Four digits numeric number (0 - 9) (Defautt = blank) lo-c-121 (7osss) Section 15 Maintenance Dumb Type Terminal 65.04 Line Hunting Sequence(LHS) Description Used to change the hunting sequence of idle lines on a TIE trunk group basis. By default, idle TIE lines are seized trom the smallest to the largest physicai number in order at all locations when a TIE call is initiated by a user. This may cause a frequently busy situation between a certain two locations. In this case, we recommend to change the hunting sequence at one location from ‘1 ‘(smallest-+ largest) to ‘2’ (largest +smaflest). (Password level : Two or higher) . Input Format [iTimq~((SWAT/BT)I(I)p(01-15) Index Number Explanation Index Number Trunk Group Number 01 to 16 input Value for item Number Item~ Number None Assigning Items tine Hunting Sequence Input Value 1: From the smaflest to the largest physical number of TIE lines 2: From the largest to the smallest physical number of TIE lines (Default = 1) . 10-C-123 mw - F Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................................... 1 .OO SYM command (System Maintenance Monitor) .................................... 1 .Ol System Status screen .................................................................. 1.02 Card Status screen ...................................................................... 1.03 Port Status screen ....................................................................... 1.04 Conference Trunk Status screen ................................................. 2.00 T F D command (Traffic Display). ............................................................ 2.01 Station screen .............................................................................. 2.02 Trunk Group screen ..................................................................... 2.03 Attendant Console screen ........................................................... 2.04 DISA screen ................................................................................ 2.05 OGM 1 screen ............................................................................. 2.06 OGM 2 screen ............................................................................. 2.07 AGC screen ................................................................................. G Other Features ................................................................................................. . 1 .OO PFT command (Power Failure Transfer) ................................................ 2.00 VUP command (Version-up) .................................................................. 15-2 (70695) Page 15-F-i 15-F-l 15-F-2 15-F-3 15-F-4 15-F-5 15-F-6 15-F-7 15-F-0 15-F-9 15-F-10 15-F-11 15-F-12 15-F-13 15-G-l 15-G-1 15-G-3 - 68.00 Call Forwarding-Follow Me (CFM) Description Used to allow or disallow each extension from setting “Call Forwarding-Follow Me’ feature on a COS basis. Refer to Section 4-F-2.06 and Section 5-D-2.06 ‘Call Fowarding-Follow Me” for further information. (Password level : Two or higher) Input Format Index Number I Index Number Explanation 01 to 32 COS (Class of Service) number Input Value for Item Number Item Assigning Items Nt rmhor I I Call Forwarding-Follow Me Y: Enabled N: Disabled 1(DefaukN) Input Value 3.01 Loopback Test (LBT) -for T-l Description Used to verify the validity of the T-l DIGITAL TRUNK cards and line connections. Before performing Loopback Test, set the card status to ‘OUS”. Command Format (1) OPE>LBT + Item1 + Item2 -I (2) OPE>LBT + Item1 + Item2 + Item3 7 Item1 Item2 Item3 1 or2 101 ,105,109,201,205, 209,301,305,309 (Card No.)+~ None 1: Internal Loopback*’ 2: External Loopback’ G=JW (DTMF Generator No.) xxx : Card No. yy :Ol too6 R=YY (DTMF Receiver No.) xxx: Card No. yy :Ol to24 l . l.Loopback test is completed automatically inside the T-l DIGITAL TRUNK card. ‘2.Loopback test is completed between the T-l DIGITAL TRUNK card and the external equipment (CSU, DSU). In this case, loopbxk mode should be set at the external terminal beforehand. ‘3.When a card No. is specified, DTMF Generator No.1 and DTMF Receiver No.1 of that card are used for the test. . Results Display Error Indication I I OK I I Voice error I I Description Normal I Speech path failure Control signal path failure 15-E-5-1 (70695)M I D. Error Message Tables 1.00 Error Messages Related to the Assigning Items in the Same Command If there is a wrong entry in the displayed screen, the following appears on the message line when storing the entry: “DATA ERROR (XXX).” DATA ERROR No. The (XXX) indicates one of the error message numbers shown below and possible causes of the errors and countermeasures for them are as follows. Probable Cause Countermeasure (page length)-(skip length) < 6 Make (page length)-(skip length) Z 6. 101 (receive digit) 2 (delete digit) is not established in - Special Attended DID screen. Make (receive digit) 2 (delete digit). 102 Restriction Level-Operator s Restriction LevelInternational is not established in - Operation (l/3) screen Make Restriction Level-Operation 6 Restriction Level-International 110 Day-night combination in the incoming mode is not correct. Change the day-night combination in incoming mode. 130 Combination of the terminals of operators I,2 is incorrect. Change the combination of terminals for operators 1.2. 140 . DN is not installed. Designate the installed DN. 141 Attempting to assign FDN’s of UCD # 1 to # 4 for the overflow destination of UCD # 5 to # 32 Set FDN of other UCD. or extension director] number. Attempting to assign its own extension number on the key which cannot be assigned to its own extension number. DSS(ICM) DSS(DN) SDN Specify the number except its own extension number. 160 Specifying UCD number incorrectly. Assign UCD to only one ICM. 190 Date value is incorrect on the check of month, and leap year in the time and date setting soreerr. Check the date setting. L '150 / lo-D-1 (21292) 3.00 Device Status screen 3.01 System Status Initial screen I~NLIM~NI Device Status (l/4) . System Status v12.00 May.08 1995 Area-2 cp” R&j ---.--------..&.& SeH ~.--~l.----- INS INS E x p a n s i o n S h e l l l - - -- - . - Expansion Shelf 2 -.--.-..-T S W AddiMalCONF - S M D R - - - - - INS - INS Ckxk M o d e - - Master Ckxik Cafd---------- .I COMMON 2- External 101 : ;. :5: .: .; :;> 6 HRD Cpy ‘;.$ .a Description ROM version Date For Place CPU RAM Basic Shelf Expansion Shelf 1 Expansion Shelf 2 TSW Additional CONF SMDR Clock Mode Master Clock Card Software’s version The date software was originated Destination Current status of RAM area Current status of Basic Shelf Current status of Expansion Shelf 1 Current status of Expansion Shelf 2 Current status of TSW card Current status of optional Conference card Current status of SMDR device Displayed only when T-l Digital Trunk card is installed. ‘External” is displayed when the system synchronizes with the external clock ‘InternaP is displayed when the system synchronizes wfth the internal dock. Refer to Section 10-c-64.02 ‘System Ckxk Mode (CLKY for further information. Displayed only when T-l Digital Trunk card is installed. XXX” (physical card No. of the master card) is displayed when the external ckxk mode is utilized. Y - a is displayed when the internal clock mode is utilized. Refer to Section 10-C-64.03 “Master Clock Priority (CLP)’ for further information. * In above screen, a-” indicates that the device is not installed. 14-G-3 (70695)M DATA ERROR No. Probable Cause Countermeasure 414 Deleting the card is impossible, because it is Change the intercept routing destination. assigned for the intercept routing destination for the Trunk group. 415 Deleting the card is impossible, because it is assigned for doorphone call destination. Cancel the doorphone call destination. 416 Attempting to delete the ATT which is specified for incoming mode destination of a trunk group. Change the incoming mode destination. 417 Attempting to delete a DISA card which is specified for incoming mode destination of a trunk group. Change the incoming mode destination. 418 Attempting to assign NAG as Night Answer Point of a CO line belonging to a Trunk Group whose Incoming Mode (Night) is not FIXED. Assign Incoming Mode (Night) to FIXED. 420 Changing Tenant Service from ‘Yes” to ‘No” is impossible as all ATT’s are not assigned to tenant 1. Assign All’s to tenant 1. 421 Changing Tenant Service from Yes” to ‘No” is impossible as all music sources are not assigned to tenant 1. Assign music sources to tenant 1. 422 Changing Tenant Service from Yes” to ‘No” is impossible as all external pagers are not assigned to tenant 1. Assign external pagers to tenant 1. 423 Changing Tenant Service from Yes” to ‘No” is impossible as all doorphones are not assigned to tenant 1. Assign doorphones to tenant 1. 424 Changing Tenant Service from ‘Yes” to ‘No” is impossible as all DIM’s are not assigned to tenant 1. Assign DISA’s to tenant 1. 425 Changing Tenant Service from “Yes” to ‘No” is impossible as all AGCs are not assiQrwd to tenant 1. Assign AGCs to tenant 1. 426 Changing Tenant Service from “Yes” to ‘No” is impossible as all paging groups are not assiQned to tenant 1. Assffn all paging groups to tenant 1. 427 Changing Tenant Se&e from Yes” to ‘No” is impossible as all ICM Qroups are not assigned to tenant 1. Assign all KM groups to tenant 1. 428 Changing Tenant Service from Yes” to ‘No” is impossible as all trunk groups are not assigned to tenant 1 Assign all trunk groups to tenant 1. 430 Deleting expansion shelf is impossible, as one or more cards are assigned to the expansion shelf. Delete all the cards in the expansion sheff. .. 3.35 Digital trunk failure (out of synchronization) Error Code 7Oxx xx=01 to 42 : Slot number Possible cause of the malfunction T-l card (physical number xx) lost the synchronization with the clock time sent from the Central Ofice. Countermeasures Confirm that the setting of “Frame Sequence” and “Line Cording” are matched with that of the leased lines. If not, change the setting of your KX-T336 and CSU. Then check the clock mode. OK I NG Check the cabling between 7-l and CSU’ and “CSU and NIU.’ If not properly cabled, change the cabling. I * Execute Loopback Test Results NG I Replace the T-? card Nth a new one. Test(lntemal). I Test Results OK Y Test(Extemal: Execute Loopback CSU) between KX-T336 and OK NG I . 1 1 1 Check the CSU. If’ not good, replace it with a new one. I ’ 1 1 Or, check the equipment in other switching system which I Note End 1 Another T-l card with next priority will work as a master card, if more than two T-l cards were registered to the system by CLP command (Refer to Section 64.63) beforehand. Othenvise, the system will synchronize with the system internal clock. 14-E-37-1 (70695)M 3.37 trunk failure reception) Error Code 72xx xx=01 to 42 : Slot number Possible cause of the malfunction T-l card (physical number xx) received the signal from the Central Office. Countermeasures AIS (Alarm indication Signal) Confirm that the setting of ‘Frame Sequence” and “Line N G J, Check the cabling between ‘T-l and CSU’ and ‘CSU and NIU.’ If not properfy cabled, change the cabling. OK Execute Loopback Test Results NG NG Test(lntemal). I Test Results Replace the T-l card with a n:r/ OK I I 1 Execute Loopback Test(Extemal: between KX-T336 and 1CSU) OK 1 NG Check the CSU. If not good, replace it with a new one. NO ,I I OK . Note Another T-l card with next priority will work as a master card, if more than two T-l cards were registered to the system by CLP command (Refer to Section 64.03) beforehand. Otherwise, the system will synchronize with the system internal clock. .. 14-E-37-3 (70695)M DATA ERROR No. I I Probable Cause A checksum error has been detected. 030 Communication line is defective, or backup data is destroyed. I improper data is received. 031 I I 1 Countermeasure I I Execution is impossible during off-line. Communication link is defective, or backup data is destroyed. .I I I Execute during on-line. Impossible. Some required items are omitted. 043 The number of equipment you attempt to assign is over the limit. Assign the equipment within the limit of number. 045 Slot number you specified is not valid. (DTM, LBT, DSP commands) Specify the slot in which T-l/E-l card is installed. 046 Card type you specified is not valid. (DlM LBT, DSP commands) Specify the T-l/E-l card. 047 The status of the card you specified is not vaiid. (DTM. LBT, DSP commands) Change the status to valid one. No DTMF Generator/Receiver is installed on the card you specified. (DTM, LBT commands) Install the optional DTMF Generator/Receiver card. You specified the DTMF Generator/Receiver of diierent cards.(DTM. LBT commands) Specify the DTMF Generator/Receiver of the same card. II 048 049 I Enter the required items. 042 I . lo-o-7 (70695) I (Section 14) Maintenance VT220 and Compatibles Contents ....................................... A Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 14-A-l . .................................................... B System Administration ................................ 1 .OO On-Site Administration ........................................................................... 1 .Ol Logging in to the System ............................................................. 1.02 Administration Main Menu screen ............................................... 2.00 System Administration from a Remote Location .................................... 14-B-1 C Device Status ................................................................................................... 14-C-1 1.00 Service Commands and Their Functions ............................................... 1 .Ol INS (In Service) Command .......................................................... 1.02 OUS (Out of Setice) Command ................................................. 2.00 Definition of Operating Status ............................................................... 2.01 Shelf, Slot, Resource ................................................................... 2.02 Port .............................................................................................. 2.03 Interacfions among Devices ........................................................ 2.04 Changes of the Shelf Status ........................................................ 2.05 Changes of the Slot Status .......................................................... D Self-Test (System-Detected Troubles) ............................................................. 1 .OO Error Record Display ............................................................................. 1 .Ol Start Time of Self-Test ................................................................. 1.02 Error Log ...................................................................................... 1.03 Printing Out the Automatic Failure Reporting .............................. 1.04 Local Alarin .................................................................................. 1.05 Remote Alarm .............................................................................. 2.00 Clearing System-Detected Troubles ...................................................... 2.01 Introduction .................................................................................. 2.02 Consulting the Error Log .............................................................. 2.03 Background Diagnostic Error List ................................................ E Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 .OO Introduction ............................................................................................ 2.00 Troubleshooting via the ,LED Indicators ................................................. 3.00 Troubleshooting v i a Error Log Records ................................................. 3.01 Error Log Record List ................ ..T...~ ........................................... 3.02 System Reset caused by CPU Runaway (Restart Procedure) .... 3.03 TSW clock down (Internal/External) ......................... ..” ............... 3.04 Basic shelf power down (DC) ...................................................... 3.05 Basic shelf power down (AC) ...................................................... 14-1 (70695) 14-6-l 14-B-l 14-B-2 14-B-3 14-c-1 14-C-2 14-c-3 14-c-4 14-c-4 14-c-4 14-C-4 14-c-5 14-C-6 14-D-1 14-D-l 14-D-1 14-D-1 14-D-1 14-D-2 14-D-3 14-D-4 14-D-4 14-D-4 14-D-5 14-E-l 14-E-1 14-E-2 14-E-4 14-E-4 14-E-5 14-E-S 14-E-7 14-E-S - 1 .Oi System Status screen Command Format OPE>SYM 1 kvice Status (l/4) 10~~1 bt0Nl systenl status ROM l/e&on .---_-.---lm v12.00 Date-----...___-_-. -_-May.08 1995 For p&e-..--.---..__.-. -_-- cpu R&f .-..---B&j Shelf . ..----_._-._Expansion Shelf 1------Expansion Shetl2 ---TSW aC()NF--.--S M D R - - Area-2 INS INS INS INS Clodt Mode External Mastercbckcard--------- 101 Description ROM version Date For Place CPU RAM Basic Shelf Expansion Shelf 1 Expansion Shelf 2 TSW Additional CONF SMDR Clock Mode Software’s version The date software was originated Destination Current status of RAM area Current status of Basic Shelf Current status of Expansion Shelf 1 Current status of Expansion Shelf 2 Current status of TSW card Current status of optional Conference card Current status of SMDR device Displayed only when T-l Digital Trunk card is installed. ‘ExtemaF is displayed when the system synchronizes with the external clock. ‘Intemaf” is displayed when the system synchronizes wtth the internal clock. Refer to Section 1 O-C-34.02 ‘System Clock Mode (Cu<)’ for further information. Master Clock Card - Displayed only when T-l Digital Trunk card is installed. Woe (physical card No. of the master card) is displayed when the external clock mode is utiliied. .- - is displayed when the internal clock mode is utilized. Refer to Section 1 GG64.03 ‘Master Clock Priorfty (CLP)” for further information. 3lf In above screen, .- ” indicates that the device is not installed. 1 S-F-2 (70695)M Page 3.03 Card Test procedure.. .................................................................. 3.04 Card Test Results screen ............................................................ 4.00 Testing the Ports.. ................................................................................. 4.01 Functions to be Verified ............................................................... 4.02 Port Test initial screen ................................................................. 4.03 Port Test procedure ..................................................................... 4.04 Port Test Results screen .............................................................. 5.00 Testing PITS and ATT ............................................................................ 5.01 Functions to be Verified.. ............................................................. 5.02 PITS and ATT Test Initial screen ................................................. 5.03 PITS and ATT Test procedure ..................................................... 5.04 PITS a n d ATT Test Results screen.. ............................................ 6.00 Return Messages ................................................................................... 14-F-5 G Monitor ............................................................................................................. 1 .OO Monitor Main Menu screen .................................................................... 2.00 Error L o g screen ................................................................................... 3.00 Device Status screen.. ........................................................................... 3.01 System Status Initial screen ........................................................ 3.02 Card Status screen.. .................................................................... 3.03 Port Status screen ....................................................................... 3.64 Conference Trunk Status screen ................................................. 4.00 Traffic Submenu screen.. ....................................................................... 4.01 Station initial Screen .................................................................... . . 4.02 Trunk Group Initial screen ........................................................... 4.03 Attendant Console Initial screen.. ................................................ 4.04 DISA screen ................................................................................ 4.05 O G M 1 screen.. ........................................................................... . 4.06 O G M 2 screen ............................................................................. 4.07 A G C screen ................................................................................. 14-G-l H Other Features ................................................................................................. 1 .OO Power Failure Transfer Assignment ...................................................... 14-3 (70695)M 14-F-6 14-F-7 14-F-7 14-F-8 14-F-9 14-F-l 0 14-F-1 1 14-F-11 14-F-12 14-F-13 14-F-14 14-F-1 5 14-G-l 14-G-2 14-G-3 14-G-3 14-G-4 14-G-5 14-G-6 14-G-7 14-G-8 . 14-G-9 14-G-10 14-G-11 14-G-12 14-G-1 3 14-G-14 14-H-1 14-H-1 . 2.00 VUP command (Version-up) Description Used to initialize the RAM area of the newly added system memory while keeping the current settings intact. This command is valid when one of the following version of ROM is replaced with a new version of ROM (version 12.xX and above). - V.6.5X,V.8.XX,V.9.XX,V.lO.XX Command Format OPE>VUP + old ROM Version No. (Vxxxx). J * If your old ROM version is V.6.5X or lower, enter 11.6.50”. If your old ROM version is V.7.XX, enter Y.8.00”. Display Example ; OPE>VUP V10.50 V10.50 -> V12.00 version up , ., Are You Sure? (Y; Yes, Other: No) = :OK ;OPE> Conditions After replacing an old version of ROM with a new version of ROM (Version 12.xX or higher), “Additional System Memory Initialization” should be done before programming the newly added features. Then newly added system memory is initialized by default values. Note: If you do not execute this operation after replacing the ROM, the system maifunction . occur. l may 15-G-3 (70695) 72xx MN Digital trunk failure D-Trunk Failure D-TRK 7%~ MN Digital trunk failure D-Trunk Failure D-TRK DTMF generator failure DTMF receiver failure Tone detector failure HDLC failure Port link failure OHCA SW failure OHCA not installed TSW DTMF GJFI. failure DTMF G. Failure DTMF R. Failure Tone Detector HDLC Failure DTMF G. DTMF R. TN DTCT HDLC OHCA OHCA SW 8Oxx MN 9rxx MN Ayxx MN Byxx MN cyxx -DO00 M N Dyxx -FFFF MN SW Failure TSW Failure Legend: MJ-Major Alarm MN-Minor Alarm 14-E-4-1 c/OS951 TSW FLT line trouble (AIS signal reception) line trouble (frame trouble) Panasonic KX-T336 SYSTEM Programming Forms -\ Panasonic Company Division of Matsushita Electric Corporation of America One Panasonic Way, Secaucus, New Jersey 07094 Panasonic Company (West) of America, Division of Matsushita Electric Corporation of America 6550 Katella Avenue, Cypress, California 90630 Panasonic Sales Company (“PSCY), Division of Matsushita Electric of Puerto Rico, inc. San Gabriel Industrial Park, 65th Infantry Avenue, KM 9.5, Carolina, P. R. 00630 KX - A221 Printed in Japan PQOX6488ZA Q069100 3.02 System Reset caused by CPU Runaway (Restart Procedure) Error Code 0100 = Overflow of the watch dog timer. 0200 = Software Infinite Loop Possible cause of the malfunction 1) External circumstance, such as introduced noise 2) Hardware is defective Countermeasures Does the trouble occur frequently? No Yes Replace the CPU card’ No change in condition Replace the TSW card No change in condition No change in condition Replace the Shelf J I Consult the Service Center I Note OK I No change in condition End I 1) If a reset occurs 16 times/in one hour due to overflow of the watch dog timer, the restart procedure is not activated and the system will be shut down. Press the RESET button to restart the procedure. l It is recommended to have a current copy of the program on disk or tape facilitate accurate and rapid recovery. 14-E-5 to 3.03 TSW clock down (Internal/External) (1) Internal clock down Error Code 0300 Possible cause of the malfunction 1) TSW card connection error 2) TSW card clock link failure (Internal) Countermeasures Is the trouble registered in the Error Log ? Yes I I No Is an Extension/CO call possible ? I Replace the TSW card I OK No change in condition Replace the Shelf Note Yes If the TSW clock malfunction occurs: 1) The attendant console does not function. (Communication to the LPR becomes impossible) 2) Calling becomes impossible 3) Power Failure Transfer will be activated 14-E-6 (70695) (2) External clock down Error Code 0301 Possible cause of the malfunction 1) TSW card connection error 2) TSW card clock link failure (External) “TSW external clock down “has occurred, and the T-l master card does not synchronize with the clock time sent from the Central office. l Countermeasures $1 Is the trouble registered in the Error Replace the T-l card. I I OK I1 Reolace the TSW card. ) I I . Note Another T-l card v&h next priority will work as a master card, if more than two T-l cards were registered to the system by CLP command (Refer to Section 64.03) beforehand. Othennrise, the system will synchronize with the system internal clock. 14-E-6-1 (70695)M - Section 15 Maintenance Dumb Type Terminal (Section 15) Maintenance Dumb Type Terminal . Contents A Introduction B ...................................................................................................... System Administration ..................................................................................... 1 . O O On-site Administration ........................................................................... 1 .Ol Logging i n to the System.. ........................................................... 1.02 Dumb Operation Mode ................................................................ 2.00 System Administration from a Remote Location .................................... C Device Status ................................................................................................... 1 .OO Service Commands and Their Functions ............................................... 1 .Ol INS (In Service) command .......................................................... 1.02 OUS (Out of Service) command .................................................. D Self-Test (System-Detected 1 .OO Error 1 .Ol 1.02 1.03 1.04 1.05 E Troubles) ............................................................. Record Display ............................................................................. Start Time of Self-Test ................................................................. . .................................... .Error Log.. ............................................... Printing Out the Automatic Failure Reporting .............................. Local Alarm.. ......................................... ..- ................................... Remote Alarm .............................................................................. Page 15-A-l 15-B-l 15-B-l 15-B-1 15-B-l 15-B-2 15-c-1 15-C-l 15-C-1 15-C-2 15-D-1 15-D-l 15-D-l 15-D-1 15-D-l 15-D-2 15-D-3 Functional Test by Entering Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-E-1 1 .OO Introduction ............................................................................................ 2.00 Functions to be Verified ......................................................................... 2.01 Card Test . ,.................................................................................... 2.02 Port Test ...................................................................................... 2.03 PITS and Aii Test ...................................................................... 3.09 TST command (Test) ............................................................................. 3.01- Loopback Test (LBT) - for T-l ..................................................... 3.62 DTMFGR Diagnosis (DTM) - for T-l ......................................... 4.09 Card Test Results Display ...... ..- ............................................................ 5.00 Port Test Results Display ....................................................................... 6.00 PITS and ATT Test Results Display ....................................................... 15-E-l 15-E-2 15-E-2 15-E-3 15-E-4 15-E-5 15-E-5-1 15-E-5-2 15-E-6 15-E-7 15-E-6 15-1 (70695)M . F Monitor ............................................................................................................. 1 .OO SYM command (System Maintenance Monitor) .................................... 1 .Ol System Status screen .................................................................. 1.02 Card Status screen ...................................................................... 1.03 Port Status screen ....................................................................... 1.04 Conference Trunk Status screen ................................................. 2.00 TFD command (Traffic Display) ............................................................. 2.01 Station screen .............................................................................. 2.02 Trunk Group screen ..................................................................... 2.03 Attendant Console screen ........................................................... 2.04 DISA screen ................................................................................ 2.05 DGM 1 screen ............................................................................. 2.06 OGM 2 screen ............................................................................. 2.07 AGC screen ................................................................................. G Other Features ................................................................................................. . 1.00 P?FT command (Power Failure Transfer) ................................................ 2.00 VUP command (Version-up) .................................................................. 15-2 (70695) Page 15-F-l 15-F-1 15-F-2 15-F-3 15-F-4 15-F-5 15-F-6 15-F-7 15-F-8 15-F-9 15-F-10 15-F-11 15-F-1 2 15-F-13 15-G-l 15-G-1 15-G-3 3.02 DTMF-G/R Diagnosis (DTM) - for T-l Description Used to check the validity of DTMF Generators and Receivers on the Before executing the test, set the status of the card to “OUS”. Tl DIGITAL TRUNK cards. Command Format (1) OPE>DTM + Item1 + Item2 1 Operation Item1 G/R Status display STS G/R ous ous G/R INS INS Item2 101,105,109,201,205,209,301,305,309 (Card No.) G xxxyy (Generator No.) or R xxxyy (Receiver No.) xxx : Card No. yy : Generator No. (01 to 06) or Receiver No. (01 to 24) G-R Test 101.105,109,201,205,209,301,305,309 (Card No.) TST Result Display G/R status display G/R test results display OPE>DTM STS 101 1 DTMF-G 01 02 03 04 05 06 1 0 -.- DTMF-R 01 02 03 04 05 06 07 0 8 I0III.0I0 DTMF-R 09 10 11 12 13 14 15 1 6 w e m m M w DTMF-R 17 18 19 20 21 22 23 2 4 w . w - w - M Indication I 0 ; OPE> DTM 9 , DTMF-G t .* DTMF-R t ., DTMF-R ., t. DTMF-R I Description Indication INS (In Servicb) OUS (Out of Service) Not installed OK NG ~ 15-E-5-2 (70695)M TST 101 01 02 OK NG 01 02 OK OK 09 1 0 17 1 8 - -I 03 03 OK 11 19 s 04 04 NG 12 20 - 05 05 OK 13 s 21 w 06 06 OK 14 e 22 - Description Normal Failure Not installed 07 OK 15 23 - 08 NG 16 24 - 3.00 Device Status screen 3.01 System Status Initial screen Device Status (l/4) . I~NLIM~NI System Status ROM version __..-__. --.--. Da&-..-.--....--..._-..-..--.--. For pke------.------- v12.00 cpu RAM _-.._--_...- - *.__-.. 6,&c aelf -----.----.-&,a&~,, S,,e,f ,-----. &pane&n Shelf 2 - .-.... --- INS INS INS T S W Additional CONF---.SMDR --- External 101 Master Cbck Card------ +j:’ Area-2 INS Ckck Mode - - - - - - 1 CO,&,O,,, 2.1: May.08 1995 . : . ,,. .c : .,. . ‘5, .8 HRD cpy :yj Description ROM version Date For Place CPU RAM Basic Shelf Expansion Shelf 1 Expansion Shelf 2 TSW Additional CONF SMDR Clock Mode 8. y Software’s version - The date software was originated - Destination - Current status of RAM area - Current status of Basic Shelf - Current status of Expansion Shelf 1 - Current status of Expansion Shelf 2 - Current status of TSW card - Current status of optional Conference card Current status of SMDR device - Displayed only when T-l Digital Trunk card is installed. ‘Extemaf” is displayed when the system synchronizes with the external clock. . ‘Internal” is displayed when the system synchronizes with the internal clock. Refer to Section 1 @C-64.02 ‘System Clock Mode (CLKY for further information. Master Clock Card - Displayed only when T-l Digital Trunk card is installed. %XX” (physical card No. of the master card) is displayed when the external deck mode is utilized. Y - ” is displayed when the internal clock mode is utilized. Refer to Section 1 O-C-64.03 “Master Clock Priority (CLP)’ for further information. * In above screen, ‘- m indicates that the device is not installed. 14-G-3 (70695)M 3.02 Card Status screen Ievice Status G/4) IONL IMONI I 01 02 03 04 LCOT LCOT LCOT 0 0 0 08 09 10 11 12 13 14 15 0 0 0 0 0 0 0 0 0 0 0 0 Card Status Basic Shelf 01 02 03 04 PLC PLC I I PLC Expansion Shelf 1 I PLC I 0 5 PLC I 06 07 08 09 10 11 12 PLC I PLC PLC I I PLC PLC PLC PLC I I I I 82 OHCA PLC PLC F F PLC F Expansion Shelf 2 PLC F PLC F LCOT 0 5 LCOT 06 LCOT 07 LCOT PLC PLC PLC PLC LCOT LCOT LCOT LCOT F F F F F F F F LCOT LCOT LCOT LCOT LCOT ATLC DPH RMT PLC F 05 PLC F 06 07 08 09 10 11 12 13 14 15 F I 83 TSW 01 02 03 04 I: In Service, 0: Out of Service, F: Fault E’COMMON 2’ .3. '4' 5 Description In the above screen, a blank indicates that a card is not installed in the slot. 14-G-4 6 ‘.’ HRDCpy’.7i ::b; 3.35 Digital trunk failure (out of synchronization) Error Code 70xX Possible cause of the malfunction T-l card (physical number xx) lost the synchronization with the clock time sent from the Central Office. xx=01 to 42 : Slot number Countermeasures Confirm that the setting of “Frame Sequence” and “Line Cording” are matched with that of the leased lines. If not, change the setting of your KX-T336 and CSU. Then check the clock mode. OK NG . Check the cabling between ‘T-1 and CSU’ and ‘CSU and NIU.’ If not properly cabled, change the cabling. .A Execute Loopback Test Results NG I Test(lntemal). Test Results Execute Loopback CSU) OK Test(Extemal: between KX-T336 and NG Check the CSU. If‘ not good, replace it with a new one. NG ,I OK I Ask the T-l carrier to check the line conditions. Or, check the equipment in other switching system which your T-l lines are connected with. I Y End I Another T-l card with next priority will work as a master card, if more than two T-l cards were registered to the system by .CLP command (Refer to Section 64.03) beforehand. Otherwise, the system will synchronize with the system internal clock. 14-E-37-1 (70695)fvl 3.36 Digital trunk failure (RAI signal reception) Error Code 71xx xx=01 to 42 : Slot number Possible Cause of the malfunction T-l card (physical number xx) received the signal sent from the Central Office. Countermeasures Ask the T-l carrier to check the line conditions. Or, check the equipment in other switching system which your T-l lines are connected with. Note None 14-E-37-2 (70695)M RAI (Remote Alarm indication) 3.37 Digital trunk failure (AIS signal reception) Error Code 72xx xx=01 to 42 : Slot number Possible cause of the malfunction T-l card (physical number xx) received the signal from the Central Office. Countermeasures AIS (Alarm Indication Signal) Confirm that the setting of “Frame Sequence” and “Line Cording” are matched with that of the leased lines. If not, change the setttng of your KX-T336 and CSU. /Then check the ciockmode., :K ~~~~ 1 Check the cabling between ‘T-l and CSU’ and ‘CSU and NIU.’ If not properfy cabled, change the cabling. I OK NG Execute Loopback Test(lntemal). I Test Results NG I Test Results I 1 Execute Loopback ICSU) 1 Test(Extemal: between KX-T336 and - OK NG I L 1 1 1 Check the CSU. If not good, replace it with a new one. I 1 Ask the T-l carrier to check the line conditions. Or, check the equipment in other switching system which your T-l lines are connected with. . Note Another T-l card with next priority will work as a master card, if more than two T-l cards were registered to the system by CLP command (Refer to Section 64.03) beforehand. Otherwise, the system will synchronize with the system internal clock. 14-E-37-3 (70695)M 1 I 3.38 Digital trunk failure (frame trouble) Error Code 7.5~~ xx=01 to 42 : Slot number Possible cause of the malfunction On booting-up of T-l card (physical number xx), it failed to synchronize with the clock time sent from the Central Office. Countermeasures Confirm that the setting of “Frame Sequence’ and “Line Cording” are matched with that of the leased lines. If not, change the setting of your KX-T336 and CSU. Then check the clock mode. [ Check the cabling between ‘T-l and CSU’ and ‘CSU 1 1 and NIU.’ If not property cabled, change the cabling. 1 I 1 OK NG Test(lntemal). Execute Loopback Test Results NG I . Test Results Y . Execute Loopback CSU) Test( External: between KX-T336 and OK NG I , ‘ 1 1 Check the CSU. If not good, replace it with a new one. Ask the T-l carrier to check th8 line conditions. Or, check the equipment in other switching system which your T-l lines are connected with. \, I‘ . II Note Another two T-l Section system End I I T-l card with next priority will work as a master card, if more than cards were registered to the system by CLP command (Refer to 64.03) beforehand. Otherwise, the system will synchronize with the internal clock. 14-E-374 (70695)M 1 3.04 Basic shelf power down (DC) Error Code 0400 Possible cause of the malfunction 1) 2) 3) 4) AC power cord is unplugged Power Failure Power Switch is turned off Malfunction in the Power Supply Unit of the Basic Shelf, or the trouble with the Power Supply System (Backboard, CPU card) of the Shelf - Countermeasures Did the above item 1 ), 2) or 3) occur at the recorded time of the Error Loo ? Yes No 1 Does the trouble occur frequentfy? Yes 1 I No . O K OK . Replace the Power Supply Unit No change in condition ” Replace the CPU card’ I No change in condition I Replace the Shelf I Note l 1 It is recommended to have a current copy of the program on disk or tape facilitate accurate and rapid recovery. .. 14-E-7 to 1 .Ol System Status screen Command Format OPE>SYM 1 10~~1 MOM t kvice status (l/4) system status ROM Version-_---..----..--D&----.----.-For pke-.---.----- cpu R&j ... . ---.--. B&c Shelf . ..----.-.-.Expansion Shelf l --------Expansion S h e l f 2 - TSW A d d i i CONF----SMDR .-w---m Cbck M o d e - MasterCbdcCafd-- .- v12.00 May.08 1995 Area-2 INS INS INS INS External 101 Description ROM version - Software’s version Date - The date software was originated For Place - Destination CPU RAM - Current status of RAM area Basic Shelf - Current status of Basic Shelf Expansion Shelf 1 - Current status of Expansion Shelf 1 Expansion Shelf 2 - Current status of Expansion Shelf 2 TSW - Current status of TSW card Additional CONF - Current status of optional Conference card SMDR - Current status of SMDR device Displayed only when T-l Digital Trunk card is installed. Clock Mode . ‘Extemaf is displayed when the system synchronizes with the external clock. ‘Internal” is displayed when the system synchronizes with the internal clock. Refer to Section 1 O-C-64.02 ‘System Clock Mode (CLK)’ for further information. Master Clock Card - Displayed only when T-l Digital Trunk card is installed. 9ooc (physical card No. of the master card) is displayed when the external clock mode is utilized. .-” is displayed when the internal clock mode is utilized. Refer to Section 1 O-C-64.03 ‘Master Clock Priority (CLP)” for futther information. .. * In above screen, “- ” indicates that the device is not installed. 1 S-F-2 (70695)M 1.02 Card Status screen Command Format OPE>SYM 2 3 )evice Status (2/4) IONLIMONI 1 Card Status Basic Shelf I: . 01 02 03 04 PLC PLC PLC PLC I I I I Expansion Shelf 1 0 5 PLC I 06 07 08 09 10 11 12 PLC PLC PLC I I I 01 PLC 02 PLC 03 PLC 04 PLC 05 PLC 06 PLC 07 PLC 08 PLC PLC I 09PLC F 09 LCOT PLC PLC PLC I I I 82 OHCA 83 TSW F I 10 PLC 11 PLC 12 LCOT 13 LCOT 14 LCOT 15 LCOT F F F F F F 10 LCOT 11 LCOT 12 LCOT 13ATLC 14 DPH 15 RMT In Service, 0: Out of Service, F: Fault . Description In the above screen, a blank indicates that a card is not installed in the slot. 15-F-3 F F F Expansion Shelf 2 01 LCOT 02 LCOT 03 LCOT 0 0 0 F F 04 LCOT 05 LCOT 0 0 F F F 06 LCOT 07 LCOT 08 LCOT 0 0 0 0 0 0 0 0 0 0 2.00 VUP command (Version-up) Description Used to initialize the RAM area of the newly added system memory while keeping the current settings intact. This command is valid when one of the following version of ROM is replaced with a new version of ROM (version 1 LXX and above). . V.6.5X,V.8.XX,V.S.XX,V.lO.XX Command Format OPE>VUP + old ROM Version No. (Vxxxx)* J l If your old ROM version is V.6.5X or lower, enter 11.6.50”. If your old ROM version is V.7.XX, enter “V.8.00”. Display Example ; OPE>VUP V10.50 V10.50 -> V12.00 version up , Are You Sure? (Y; Yes, Other: No) = , ;OK ;OPE> Conditions After replacing an old version of ROM with a new version of ROM (Version 12.xX or higher), “Additional System Memory initialization” should be done before programming the newly added features. Then newly added system memory is initialized by default values. Note: If you do not execute this operation after replacing the ROM, the system malfunction may . occur. l 15-G-3 (70695) Panasonic KX-T336 SYSTEM Programming Forms Panasonic Company Division of Matsushita Electric Corporation of America One Panasonic Way, Secaucus, New Jersey 07094 Panasonic Company (West) of America, Division of Matsushita Electric Corporation of America 6550 Kateiia Avenue, Cypress, California 90630 Panasonic Sales Company (“PSC”), Division of Matsushita Electric of Puerto Rico, inc. San Gabriel Industrial Park, 65th Infantry Avenue, KM 9.5, Carolina, P. R. 00630 KX - A221 Printed in Japan PQQX6488ZA Q069100 1. Panasonic KX-T336 System Installation 2. Configuration CONFIGURATION-SYSTEM ASSIGNMENT Version 1 .O i Item - -.------- Set Data Expansion Shelf 0 No 0 1 Shelf TSW Additional CONF 0 Yes C l No 2-l 0 Defa,:: :Vatko -m-i ___. _ 2 Shelves I Adtomaitc set I CONFIGURATION-SLOT ASSIGNMENT (I/3) Item Slot No. FS 01 FS 02 Fs O3 Default Value Set Data 7 i 2’ ,,ank. z PLC. c HLC. q SLC, q LCOT, q GCOT ~DID, c AGC. ,~DsA. COPX. q ATLC, q DPH. q RMT Automatic C 3lank. E PLC. C HLC. q SLC, IJLCOT. q GCOT. 7DlD, C AGC. GDISA, COPX, q ATLC, q DPH. ORMT Automatic set C Blank. C PLC. C HLC, IJSLC. OLCOT, q ;C AGC. ODISA, COPX. q ATLC. q IDPH. q IGCOT. aDID, IRMT : /J Blank, q PLC, C HLC. q SLC, q LCOT. q GCOT. ODlD, F S 0 4 i/ C AGC. ODISA, COPX. q ATLC, q IDPH. q IRMT / E Blank, 17 PLC, C HLC, q SLC, aLCOT, q GCOT, q IC AGC. ~DISA. COPX. q ATLC, q DPH. q IRMT DlD. FS 06 i I-J Blank, 0 PLC, C HLC. q SLC, OLCOT, q GCOT. q C AGC. q DISA. COPX, q ATLC, q DPH, q JRMT DID, FS 07 C Blank. q PLC, C HLC. q SLC, q LCOT. IJGCOT. C; AGC. ODISA, EOPX, q ATLC, q DPH. q RMT DlD, FS 08 0 Blank. [7 PLC. c HLC. q SLC, q LCOT. q IGCOT, q GAGC. q DISA. COPX, q ATK, q IDPH. l%MT DlD, E Blank, q PLC, CHLC. E AGC. q JDISA, COPX, DlD, FS 09 FS 10 E Blank,q PLC. CHLC, q SLC. q LCOT, OGCOT. c AGC, 001s~. COPX, q ATK, q DPH. q RMT FS 11 @ Blank, q PLC. QHLC, ESLC. q ]LCOT, q GCOT, q IDID, E AGC. q DISA, q OPX, q ATLC. 00~~. q RMT Fs O5 Basic Shelf FS 12 C Blank, BS 01 CPU BS 02 OHCA . BS 03 TSW Note: FS select sequence “Blank” - PLC -HLC q PLC. n HLC, C! AGC. 00~1, Eopx, q q q SLC, q LCOT, q GCOT. ATLC. q DPH. IJRMT SLC, [~ATLC, q q ---* SLC +LCOT -GCOT --w DID --wAGC t 2-2 q q q IDlD. LCOT, q GCOT, ODID, IDPH. q RMT set Automatic set Automatic set Automatic set Automatic set Automatic set Automatic set Automatic set Automatic set Automatic set Automatic set -+DISA - OPX -ATLC -DPH -RMT CONFIGURATION-SLOT ASSIGNMENT (2/3) Slot Item Set Data No. - Expansion Shell 1 I I I I - FS 01 FS 02 [7 Blank, 0 PLC. OHLC, q q AGC. q DISA. izOPX. SLC. q LCOT. ATLC, CIDPH. q q I I I - c] Blank.0 PLC, THLC, q SLC, aLCOT. CGsCT IDls:. q AGC. ODEA. 10o~x, q ATLC, q DPH. SRM: FS 04 FS 05 FS 06 FS 07 I FS 10 GCOT. q ORMT q q Blank, q PLC. q HLC, OSLC. q LCOT. q AGC, q DISA, OOPX, q ATLC, q DPH. GCOT. q ORMT q q Blank, q PL< q HLC, q SLC. q LCOT, q GCOT. q AGC, q DISA. OOPX, q ATLC. q DPH, ORMT q HLC, q SLC, q OPX, OATLC, q Biank,O PLC. q 0 AGC, q DISA, q q I I I FS 11 FS 12 0 q q q q 0 Blank, q q DISA, PLC. OHLC, q q OPX, q q q PLC. q HLC, q SLC. q DISA, q OPX, OATLC. q Blank.0 PLC.OHLC. OSLC. q q DlSA. OOPX. O ATLC. q q GCOT, q DID. Blank.0 PLC. q HLC, q SLC, q 0 AGC, ODISA. 001%. q ATLC, q q 0 FS 14 q q FS 15 q q Blank, AGC, q q DISA, PLC. OHLC. q q OPX, q Blank, q PLC, OHLC. q AGC, q DISA, OOPX, q LCOT, q DPH, q SLC, q LCOT, ATLC, q DPH, SLC, q LCOT, DtD, DlD, DID, q DID, q DID, q q GCOT, RMT q GCOT, ODID. mc, q DPH, q RM’T Blank, q PLC, q HLC, q SLC, q LCOT, q AGC. q DiSA, q OPX, q ATLC, q DPH, q 2-3 GCOT, RMT GCOT. RMT q set ; AutomatIC set T i Automatic set I 0 Blank, 0 PLC, q HLC. q SLC, q LCOT, q GCOT, ODID, 0 AGC, ODISA. OOPX, q ATLC, q DPH, q RMT q :dioma:r: I DiD, LCOT. OGCOT. 000 DPH. q RMT LCOT, q GCOT, q DPH, q RMT i ~-:;-a:,c set I RMT Blank. 0 PLC. q HLC, q SLC, q LCOT, q GCOT, AGC, ODISA. q OPX, q ATLC. q DPH, q RMT Blank, AGC, DID. LCOT, q GCOT q DtD ’ DPH. ORMT ’ SLC, q LCOT, q ATLC, q DPH, q AGC, FS 13 .I I GCOT. CDlD. IRMT Blank.0 PLC, q HLC, q SLC. q LCOT, q 0 AGC. q DISA, OOPX, q ATLC. q DW I 0 AGC, FS 08 FS 09 I I q q - Default j - -?/a!:e --___ DID, 1Automatic siq 1 A”to*aticset 1 1Automatic set 1 Automatic set Automatic set 1Automatic set / Automatic set Automatic set Automatic set Automatic set CONFIGURATION-SLOT ASSIGNMENT (3/3) -7 Item / i Slot No. FS ot 0 Blank.1 PLC. @HLC. CSLC, IJLCOT. CIGCOT. EDID, 0 AGC . ZDISA. COPX. CATLC, CDPH. GRMT F S 02 0 Blank. J PLC. IJHLC. CSLC, q LCOT, q IGCOT. EDlD. 0 AGC , CDISA. @OPX. CATLC, CDPH. q IRMT Automatic set FS 03 0 B1ank.a PLC. [7HLC. CSLC, IJLCOT, q GCOT. EDID. q AGC, q DISA. q OPX, EATLC, q DPW q IRMT Automatic set 0 Blank.0 PLC, q HLC. OSLC, OLCOT, q GCOT. q 0 AGC, ODEA. q OPX. CATLC, q IDPH. q RMT Automatic set Automatic set FS 04 F S 05 FS 06 Expansion Shelf 2 Set Data FS 0 7 q Blank, 17 PLC. IJ HLC. q SLC, q LCOT, q GCOT, I-J AGC. ODISA, q OPX. q ATLC, q IDW q IRMT q IDID, IDID, - 0 Blank. 0 PLC. fJHLC. q SLC, q LCOT, q GCOT. q 0 AGC, ODEA. q OPX, IJATLC. q IDPH. q IRMT lDlD, [7 Blank, (? PLC, IJ HLC. q SLC. OLCOT, q GCOT. q (-J AGC. q DISA, I-JOPX, q ATLC, q DPH, q IRMT DID. HLC. q SLC, q ILCOT. q JGCOT, q lopx, q IATLC,q IDPH.IJRMT Automatic set Automatic set Automatic set F S 08 0 Blank. 0 PLC. q Cl AGC, q DISA.q FS 09 c] Blank, [7 PLC. [7HLC, q SLC, OLCOT. q ]GCOT. [7DlD, (7 AGC, ODISA, q OPX, q ATLC. q WH, q FIMT Automatic set FS 1 0 17 Blank, q PLC. q HLC, q SLC, q LCOT, q GCOT, DOID. 0 AGC, q WSA. q opx. q ATLC, q DPH, q RMT Automatic FS 11 [7 Blank, 0 PLC. 0 HLC, IJSLC, q LCOT, q IGCOT, q 17 AGC. q DISA, q opx. UAW, q DPH. I~RMT Automatic set F S 12 0 B1ank.n PLC.IJHLC, q SLC, q iLCOT, q lGCOT, q IDID, Cl AGC. q DISA. q opx. q ~nc,q DPH. q RMT FS 1 3 0 Blank.0 PLC. q 0 AGC. ODISA. FS 1 4 0 Blank,0 PLC, q 0AGc, 001s~. q . FS 1 5 I’J Blank, 0 PLC, •l HLC. q ISLC, q LCOT, q GCOT, aDID, 0 ~~3.2, q DISA. q OPX, GATLC, q DpH, q RMT HLC. q ISLC, OLCOT. q JGCOT, q OPX. q ATLC, q DPH. q RMT q IHLC, q SLC, q LCOT, q opx. q ATLC,q IDPH,q 2-4 DID, lDlD. DID. GCOT, KIDID. RMT Automatic set set Automatic set Automatic set Automatic set Automatic set CONFIGURATION-DN ASSIGNMENT (114) >ard Type Slot No. Set Data Port No. DN DN. DN DN DN 1 2 3 4 5 6 7 -... - -. 8 --..l.._. Note: Item Card Type Slot No DN. , Selection of Value SLC, PLC, HLC, OPX 3 digits 3 or 4-digit DN, blank Default Value Automatic set Automatic set 100 to 387 ~~- J CONFIGURATION-DN ASSIGNMENT (214) --iard Type Slot No. Set Data Port No. 1 2 3 4 5 6 7 8 CONFIGURATION-DN ASSIGNMENT (3/4) Set Data ~~ Port No. DN Df!J DN DN DN DN DN DN DN 1 2 __.- 3 4 5 ! r I -. --~~ DN Card Type Slot No. I I Set Data Port No. _ DN 1 2 3 4 5 6 7 8 DN DN DN DN DN SYSTEM-OPERATION (l/2) 7 Default Value Set Data No No n J Flex, - 0 Fixed 1, -7 Key TJ Y e s , 0 N o ei4perator - et-lnternat~ona - Tan 0 Type A q - Fixed 1 Yes - (2 digits: 01 to 16) 01 - (2 digits: 01 to 16) 01 (Toil call) (Local call) (To!1 call) (Local call) (Toll call) (Local call) Type B 0 Type C I Mode OFixed 2 c l With Transfer, cl T o n e - l , 1 +NPA+NXX+XXXX NXX+XXXX NPA+NXX+XXXX NNX+XXXX l+NPA+NXX+XXXX, l+NNX+XXXX NNX+XXXX Type-A 0 Without Transfer With Transfer OTone-2 Tone-2 nder c l Yes, 0 N o Yes bsy-ovribrg-in c l Yes, 0 N o Yes 3’ cl Yes, 17 N o Yes 32 0 Yes, 17 N o Yes Source 1 c l Yes, 0 N o Yes Source 2 c l Yes, al Operator Call q No cl DN, UC0 ---- 1---- stration Device [7 VT220, pence Yes DN (3 or 4 digits: 000 to 9999), 0 0 D u m b , 0 AlTl, 0 ATT2 blank Automatic No c l Yes, 0 N o - - (1 or 2 digits: 4 to 99) blank - - (1 or 2 digits: 0 to 95) blank tion Log q tion Log cl ition I-J Separate, Name blank q Yes, q No All Call, q Toll Only, No blank blank [7Summary c] Default, 0 User Name, aDial No. 3-l blank. blank set SYSTEM-OPERATION (212) - Item rint Secret Dial rror Log Default Value I c - Yas. _ No _ Yss, 7 No blank blank raffic 1 Yes, 1 No J Yes, J No $art Time of Traffic Measure- --.-- lent II blank itart Time of Test - - ‘ 1 biank - @AM, C]PM (hour: {emote Directory Number - - - (3 or 4 digits), {emote Alarm 7 Yes, 1 No ‘rogramming - blank blank UAM, UPM (hour: i to 12, minute: 00 to 59) 1 to 12, minute: 00 to 59) No blank El Mank (Max. 26 digits) DN) with ATLC: ATT1 without ATLC: EXT 100 D N ) with ATLC: AlT2 without ATLC: None rl Al-T1 , 7 cl All-2 EXT( 3 o r 4-digit J None Iperator 2 q ATT2 cl A-l-Tl, g EXT- ( 3 o r 4-digit a None Jight Service blank with RMT: 399 without RMT: blank cl blank Iestination Address Iperator 1 blank zl Manua \uto Start Time Manual n Auto Dav Mode Niqht Mode I q PM/ _ - - q AM. q ph _ -.- - q AM.nPM - - - - q AM,nPh --‘-- q AMvOPM - - _ - i-J4 q P” _-.-- l-&AnPM - - - - q AM.UP” - -.A - - q A’4UP” _ -.- - _ [7AM. q P\ - - /-&I. UP” - -‘- - MON. - -.- - TUE. WED. THU. FRI. SAT. SUN. ?TS Programming Password - - - - (4 drglts). lNalking COS Password - - - - (4 digits), cl AM, - 3-2 - blank u blank 1234 Cl blank blank SYSTEM-TENANT Default Value Set Data cl A-1, c ATT2 m EXT - - - - None - (3 or 4-digit DN) n None 0pera:cr 2 q III AlTl. / (Tenant 2) AlT2 c l EXT - ( 3 None o r 4digti D N ) c l None Night Service (Tenant 2) cl Manual, f--J - Auto 4uto Start Time (Tenant 2) Manual Dav Mode I nAM.~PM i-jAM.uPM nAM,flPM MON. -- TUE. -- WED. THU. nAMuPM -- nAMepA nAM.C]PM nAM,nPM FRI. nAM,nPM -- nAM,OPM SAT. : -- nAM,nPM nAM,nPM -- nAM,aPM SUN. Niaht Mode : i-bM,~PM blank : : : : q AM.aPM : ‘ITS Programming Password (Tenant 2) vVa1kir-g COS Password (Tenant 2) Inter-Tenant Calling ----(4 digits), 0 blank blank - (4 digits), 0 blank blank c l Yes. 0 No No Speed Dialing-System --- (3 digits: 000 to 200) 200 Zall Park Boundary -- (2 digits: 00 to 20) 20 Wessage Waiting Boundary - (3 digits: 000 to 500) 500 e\bsent Message Boundary - - - - - 3oundary - - (2 digits: 06 to 16) 3-3 16 SYSTEM-SYSTEM TIMER - Item .~ -___ _-- ---. --. -- Set Data -. Default Value Held Call Reminder :e,:o-, (15 to 240) 60 Held Call Reminder (ATT) seconcs (15 to 240) 60 (15 to 240) 30 Transfer Recall - ._ _.. seconas Pickup Dial Waiting _ SemNs) External First Digit Time-out External Interdigit Time-out (1 to 5) 1 s e c o n d s (5 to 20) 10 - - seconds (3 to 15) 5 - - seconds (3 to 10) 5 Toll Restriction Guard Time-out - - second(s) (0 to 25) 10 Call Forwarding-No Answer Time-out - - seconds (5 to 60) 15 Intercept Routing Time-out (System) - - - seconds (15 to 240) 60 Intercept Routing Time-out (DISA) - - - seconds (15 to 240) 30 Attendant Overflow Time - - - seconds (15 to 240) 60 SMDR Duration Time second(s) External Interdigit Time-out (PBX) .. 3-4 (0 to 15) 5 SYSTEM-CLASS OF SERVICE Note: I Item Default Value Selection of Value cos 01 cos 02 j c:;p3 COS 32 Toll Restriction Level (Day) 2 diglts (01 to 16) 01 01 01 16 ~Toll Restriction Level (Night) 2 digits (01 to 16) 01 01 01 16 1 j Max. Dialing Digits 1 0: 0 0 0 0 / ; to 3 digit(s) (0 to unlimited 255) Call Forwarding/Do Not Disturb Yes/No Yes Yes Yes No Do Not Disturb Override Yes/No Yes No No No CO Forward Mode Yes/No Yes No No No CO Transfer Mode Yes/No Yes No No No Forced Account Code Mode Yes/No No No No No BSS/OHCA Yes/No Yes Yes Yes No BSSOHCA Deny Yes/No No No No No Executive Busy Override Yes/No Yes No No No Executive Busy Override Deny Yes/No No No No No Station Lock Y e s / N o No No No No Walking Station Yes/No No No No No Maintenance Capability Yes/No Yes No No No W/RSTR No RSTR No ACCS W/RSTR W/RSTR W/RSTR N o A C C S Selection of Value Default Value Trunk Group Access Trunk Group 01 to16 Yes/No Yes Special Carrier Access EQAlto4,OCClto4 Yes/No No Station Paging Access PAGl to8 Yes/No Yes External Paging Yes/No Yes ARS/Local Access item 3-5 Class of Sejnice No. 01 Item Set Data I 1 j Trunk Group Access ^. .-- ‘5’, Id - (3,: Item i ‘2 16) I/ CO Transler i Mode Y.es. ClNo Forced Amunt We M o d e izYes. ~No BWOHCA /aYes. ONo BSSiOHCA Executive Busy Override Deny Executive Busy Override Station Lock Set Data / Trunk Grcd3 j Trunk Grcd7 I Trunk Grc.,p ~Trunk GrcJp 1Trunk Grc:p Trunk Grc,p Trunk Grczp Trunk Grcup Trunk Group TrunK G r c c p Trunk Group Trunk Group Trunk Trunk Trunk Trunk /zYes. q NO jmYes, q NO q Yes, 0 No Deny / Group Group Group Group Cl C2 C3 C4 05 06 07 08 09 10 11 12 13 14 15 16 ayes.. (?No q Yes, 0 No [7Yes, 0 N O q Yes, 0 N Dyes. q No q Yes. q Yes ;, UNo q Yes. 0 No O 8::;: 8 l [?Yes, 0 NE Dyes. q No q Yes. 0 N o q Yes. q No q Yes. 0 N o q Yes. 0 N o Special Carrier Access 0 Y e s , ONo 0 Yes, q No q Yes, q No 0 W/RSTR, q Walking Station Maintenance Capability ARShcaJ Access Station Paging Access No RSTR External paging 1 External paging 2 0 No ACCS Y e s , NO Y e s , ONo Class of Service No. 02 Set Data Item Toll Restriition Level (Day) - - (01 to 16) Toll Restriction Level - - (01 to 16) (Night) Max. Dialing Digits - Call Forwarding/Do Not Disturb 0 Do Not Disturb Override ayes. CO Forward Mode 0 CO Transfer Mode Forced Account Code Mode BSSKIHCA BSSiOHCA Deny Executive Busy Override Executive Busy Override Deny Station Lock Walking Station Maintenance Capability ARSRocat Access . - - /I Item Trunk Group Access (0 to 255) Y e s , ~NO ~NO Y e s , [7No q Yes, NO 0 Yes,ONo ayes, NO 0 Yes, q No ayes. q No q Yes, q No q Yes, ONo aYes, ONo [7Yes, [7No q W/RSTR. q 0 No ACCS Special Carrier Access IIs Access No RSTR External Paging 3-6 Set Data Trunk Group 01 Trunk Group 02 Trunk Group 03 Trunk Group 04 Trunk Group 05 Trunk Group 06 Trunk Group 07 Trunk Group 08 Trunk Group 09 Trunk Group 10 Trunk Group 11 Trunk Group 12 Trunk Group 13 Trunk Group 14 Trunk Group 15 Trunk Group 16 q c]Yes, 0 N o Yes, 0 No aYes, [7 N o Yes, 0 No q q Yes, q No El Y e s , ONo Yes. 0 No ayes, 0 N o ayes, No ayes. 0 N o Dyes. 0 N o c]Yes, 0 N o Yes. No Yes. 0 No ayes, No Yes. 0 No q q q q q EOAl Yes.ONo EOA2 0 Yesa No EQA3 0 Yesa No EQA4 c] YesgINo q q q PAGl Yes.nNo PAG2 Yes.nNo PAG3 ]Yes.ONo PAG4 [7Yes,nNo q q q q OCCl Yes.ONo OCC2 0 Yes, ONo OCC3 0 Yes, 0 No OCC4Ryes, No q q q q q PAGS Yes.ONo PAG6 ayes, ONo PAG7 Yes,ONo PAG8 Yes, No External paging 1 Yes, No External paging 2 c]Yes. c] No q Class of Service No. 03 T item Toll Restrmon Level (Day) - Toll Restrhon Level (Night) - Max DialmS Digrts Call ForwarmgiDo Do N o t D i s t u r b O v e r r i d e C O Foruard Mode CO T r a n s f e r M o d e Forced Account Code Mode BSSKIHCA BSSlOHCA Deny Executive Executive Busy Override Busy - Override Deny Station Lock Walking Station Maintenance Capability ARSLocal Access (01 to 16) - (01 to 16) - Not Disturb Item Set Data drunk G r o u p lccess - (0 to 255) - IJ Yes. q JNo m Yes, ~NO ZYes. q No 0 Yes,ONo q Yes, q No 0 Yes, q No q ]Yes,ONo 0 Yes,ONo q ]Yes, ONo q Yes, ONo 0 Yes, q No ayes. q No fl W/RSTFi, ONo RSTR 0 No ACCS Special Carrier 4cCeSS itation Paging iccess :xtemal Paging Set Data Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Group Group Group Group Group Group Group Group Group Group 01 02 03 04 05 06 07 08 09 10 Trunk Group 1 1 Trunk Group 12 JYes. Trunk Group 13 Trunk Group 14 Trunk Group 15 Trunk Group 16 IYes, 0 N o C]Yes. No ,IYes. 0 N o IIYes, 0 N o q ONo El;::* q@ N0 No IYes: q No 32 IYes: IYes. IYes, 8:: q No 0 N o q No IYes, q NO IYes, [7 N o .IYes, 0 N o q EQAl Yes,ONo OCCl nYes.ONo EQA2 0 Yes.0 No OCC2 0 Yes, ONo EOA3 0 Yes.0 No OCC3 0 Yes, ONo EQA4 0 Yes.[7 No OCC4 0 Yes, 0 No PAGl PAG2 PAG3 PAG4 q q q q Yes,ONo Yes.nNo Yes.ONo Yes,ONo q PAG5 Yes.[7No PAG6 aYes. ONo PAG7 ayes, NO PAG8 Yes. No q q q a External paging 1 ayes, External paging 2 aYes, No No Class of Service No. 04 Set Data Item Toll Restriction Level (Day) - Toll Restriition Level (Night) ( 0 1 Max. Dialing Digits - Call Forwarding/Do Not Disturb Do Not Disturb Override CO Forward Mode CO Transfer Mode Forced Account Code Mode BSSK)HCA BSSKMCA Deny Executive Busy Override Executive Susy Override Deny Station Lock Walking Station Maintenance Capability ARSRocal Access - (01 to 16) t o - 1 6 ) - Trunk Group 4UXSS (0 to 255) q Yes, q No aYes, NO q Yes, ONo IJ Yes,Oklo 0 Yes, q No Dyes. UNo Dyes. ONo 0 Yes,UNo aYes, NO q Yes, q No 0 Yes, q No 0 Yes, q No q WIRSTR, ONo RSTR 0 No ACCS Item $ecial carrier 4CC8S.S itation Paging iCCf?SS External Paging 3-7 Set Data Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Group 01 Group 02 Group 03 Group 04 Group 05 Group 06 Group 07 Group 08 Group 09 Group 10 Group 11 Group 12 Group 13 Group 14 Group 15 Group 16 aYes, C]Yes, OYes, aYes. 0 0 0 0 Dyes.1 Dyes, ayes. ayes. c]Yes. ayes. aYes. ayes, C]Yes. ayes, 0 No 0 No [7 N o 0 No a No ONo 0 No ONo UNo 0 No 82 8:: EQAl OYes,nNo EQA2 0 Yes.0 No EQA3 m Yes,0 No EQA4 [7 Yes.0 No PAGl PAG2 PAG3 PAG4 q q q q No No No No Yes,ONo Yes,nNo Yes,[7No Yes,nNo OCCl OYes.nNo OCC2 0 Yes, ONo OCC3 Yes, ONo OCC4 0 Yes, ONo q q PAG5 Yes.nNo PAG6 ayes, ~NO PAG7 aYes, ONo PAG8 aYes. ONo External paging 1 Dyes, ONo External paging 2 ayes, ONo of Service No. 05 Item Se! Data -ifion L e v e l (Ga, -c,,cr: i0 .I’ k,$ :L. ;-.. . item i, drunk Grolq sccess .’ :; ‘F :ng -,- - ._.> ~ ‘C 255, bardIng DC 1401 1 ::‘,-z Xsturb Override ard Mode sfer Mode mount Code Mode I. ‘es. t..o ‘iC!S. .- . t&z q No @Yes. CA Deny ryes.. e 8usy Overriie 0 Y e s , ~NO e 8usy Override Deny .ock Station 3nce Capability alAccQs.s Trunk Trunk Trunk Trunk Trunk Group Group Group Group Group 01 02 03 04 05 Trunk Group 06 Trunk Group 07 Trunk Group 08 Trunk Group 09 Trunk Group 10 Trunk Group 11 Trunk Group 12 Trunk Group 13 Trunk Group 14 Trunk Group 15 Trunk Group 1 6 -1 Y e s . ,No I: Y e s . ~NO I-Cl Yes. ,] No CA Set Data ~No $e&il Carrier kWSS 0 Yes, 0 No q Yes. ONo q Yes, q ]No q Yes, q No 0 WIRSTR, q ktation Paging CCf?SS No RSTR External Paging 0 No ACCS q q Yes. 0 No Dyes. NO q Yes. 0 No aYes. q No a::;* Eli: Yes.1 0 No Yes. 0 No aYes. 0 N o q q q q q Yes, q No Yes, 0 No Yes. 0 No c]Yes, 0 N o aYes, No (7Ye.s. 0 N o q q EC?Al Yes.nNo EQA2 0 Yes,0 No EOA3 0 Yes.0 No EOA4 0 Yes.0 No Yes, 0 No q q q q q PAG5 q Yes,~NO PAG6 q Yes. ONo PAG7 q Yes, ONo PAG8 q Yes.nNo Yes, q NO OCCl Yes.uNo OCC2 Yes, No OCC3 I-J Yes, No OCC4 Yes, ONo q q q PAGl Yes,aNo PAG2 [7Yes,nNo PAG3 Yes.uNo PAG4 Yes,nNo External paging 1 E x t e r n a l p a g i n g 2 a Yes, ONo of Service No. 06 Item Set Data trichn Level (Day) ( 0 1 t o 1 6 ) trictim Level (Night) ( 0 1 t o 1 6 ) llirig Digits - warding/Do Not Disturb - drunk Group 4aBss (0 to 255) - 0 Yes, 0 No uard Mode q Yes. NO ayes, ONo rsfer Made aYes, lislurb Override Item DNo 4cwuntCode Mode 0 Yes, q No ICA . dyes, q N0 CA Deny re Busy Override re Elusy OverrideDeny Lock Station c]Yes, ~NO q Yes, ONo 0 Yes, 0 No q Yes. q No ayes. ONo !aflce capabiri aYes. ONo WfACWSS 0 WiRSTR. 0 No ACCS q Set Data Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Group Group Group Group Group Group Group Group Group Group Group Group Group Group Group Group q 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 ayes. 0 N o c]Yes, 0 N o Yes, 0 No ayes. 0 N o q a2 8:: ]Yes: No aYes, 0 N o ayes. No c]Yes, 0 N o ayes, 0 N o aYes. 0 N o ayes, [7 N o ayes, 0 N o Yes, 0 No ayes, 0 N o q q q q q jpedalcarrier 4cwss EQAl Yes.nNo EQA2 [7 Yes,0 No EOA3 0 Yesa No EQA4 0 Yes,ONo ;tation Paging Lcws PAGl Yes,nNo PAG5 Yes.ONo PAG2 Yes,aNo PAG6 Yes.uNo PAG3 II]Yes,C]No PAG7 aYes. DNo PAG4 Yes,ONo PAG8 Yes.ONo Exiemaf Paging External paging 1 External paging 2 aYes. 0 No No RSTR 3-8 q q q OCCl Yes,ONo OCC2 0 Yes, ONo OCC3 0 Yes, ONo OCC4 0 Yes, ONo q q q q Yes, q No Service No. 11 Item m Level (Day Set Data - (Cl to 16) - XI Level (Night1 - Digits -__- (0 to ing/Do rb Not Disturb Override Mode Mode unt Code Mode Ieny ~sy Override ~sy Override Deny ion Capability ccess item drunk Group kcess - (Cl to 16) 255) q Yes. ~NO q Yes. ?No aYes. NO q Yes. ZNo ayes, ~NO ayes, ~NO q ]Yes,~NO [7Yes, q ]No q Yes, q No q .Yes. q No q Yes, q No Dyes, nNo q W/RSTR, GNo RSTR $ecial Carrier kcess itation Paging mess rxiernal Paging 0 No ACCS Set Data Trunk Trunk Trunk Trur;k Trunk TrunK Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Group 01 Group 02 Group 03 Group 04 Group 05 Group 06 Group 07 Group 08 Group 09 Group 10 Group 11 Group 12 Group 13 Group 14 Group 15 Group 16 q Dyes. n N aYes. g N o aYes. 0 N fes. ‘/es. o 62 8NN: /?Yes: 0 N o Dyes, ONo ayes.. 0 N o aYes. c] N o aYes. No ayes, 0 N o ayes, @ N o aYes. 0 N o aYes. 0 N o 0 Yes, [7 No q EQAl Yes.ONo EOA2 c] Yes.0 No EOA3 c] Yes.0 No EQA4 ]Yes.nNo q PAGl q PAG2 q PAG3 q PAG4 q o q Yes.~NO Yes.uNo Yes.[7No Yes,ONo Yes,uNo q OCCl Yes.uNo OCC2 0 Yes, 0 No OCC3 c] Yes, 0 No OCC4 Yes.nNo - NO No NO VO UO UO UO JO JO JO JO JO IlO IO IO IO ‘es. 0 No es. UNo es. UNo es. ~NO q PAGS q Yes,ONo PAG6 aYes. q No PAG7 q Yes, ONo PAG8 q Yes, q No es. q No es, q No es. q No 3s. ONo, External paging 1 Y e s , ONo Externai paging 2 a Yes, q No Service No. 12 Item 3n Level (Day) ( 0 1 t o 1 6 ) XI Level (Night) ( 0 1 t o 1 6 ) Digii - (0 to ing/Do Not Disturb 0 rb Override ayes. Mode Made unt Code Mode Deny ~sy Override ~sy Override Deny ion ! Capability lccess Item Set Data Trunk Group Access 255) Yes, ONo UNo q Yes, q No ayes, q No ayes, UNo q Yes. q No ayes. UNo GYes, q No ayes, UNo GYes, q No 0 Yes, q No ayes, ONo 0 WiRSTR. ONo RSTR 0 No ACCS Set Data Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Group 01 Group 02 Group 03 Group 04 Group 05 Group 06 Group 07 Group 08 Group 09 Group 10 Group 11 Group 12 Group 13 Group 14 Group 15 Group 16 q Yes, 0 No q Yes. 0 No IYes, 0 N o q Yes, 0 No 8;:: 8:: Yes: 0 No ayes. 0 N o ayes, ayes, 0 N o ayes, 0 N o ayes. 0 N o ayes. 0 N o Yes, 0 No q q No q ayes. q No q Yes. 0 No q Yes,nNo OCCl q Yes.flNa special carrier Access EOAl EOA2 0 Yes.0 No EQA3 0 Yes.0 No EQA4 0 Yes.0 No Station Paging Access PAGl PAG2 PAG3 PAG4 External Paging External paging 1 [7Yes. 0 No External paging 2 ayes. 0 NO 3-11 -- q q q q Yes,[7No Yes,ONo Yes,nNo Yes,ONo OCC2 0 Yes, ONa OCC3 [7 Yes, ONa OCC4 0 Yes, 0 No q Yes,ONa q q PAG5 PAG6 Yes. ONa PAG7 Dyes, ONa PAG8 Yes.C]Na .f-JNo , ONo i8 6 - - Class of Service No. 13 ( 0 1 __ t o __ 1 6 ) (01 to Trunk Group Access 16) _ _. _ (0 to -Yes. 255) gN0 ,J Y e s , ~No BSSQHCA Deny CjYes, q No q Yes, [?No aYes, ONo q Yes, q No q Ye.s. q No Executive Busy Overrde 0 CS ;orv+a!: Lime CO Tranjf+, Mode Forced Account Code Mode BSSOHCA Station Lock Walking Station Maintenance Capability ARSLocaf Access Trunk Group Trunk Group Trunk Group Trunk Group Trunk Group Trunk Group Trunk Group Trunk Group Trunk Group Trunk Group Trunk Group Trunk Group TrunkGroup 01 02 03 04 05 06 07 08 09 10 11 12 13 Trunk Group 14 Trunk Group 15 Trunk Group 16 Y e s , ONo @Yes, 0 N o Eyes, ONo Dyes. ONo aYes. 0 N O No p; iNNo q Yes, c] Nz aYes. ONo ayes, 0 N O ayes., 0 N O q q Yes, 0No q No q No aYes. 0 N O q Yes. q No Yes. [7Yes, Special Carrier Access aYes, q No 0 Yes,ONo q Yes, ONo aYes, ONo Executive Busy Override Deny Set Data j jI t e m Set Data Station Paging Access 0 W/RSTR, ONo R S T R 0 No ACCS External Paging External paging 1 Yes, ONo E x t e r n a l p a g i n g 2 a Yes, ~NO Class of Service No. 14 Item Set Data Toll Restriction Level (Day) ( 0 1 t o 1 6 ) Toll Restriction Level (Night) ( 0 1 t o 1 6 ) Max. Dialing Digits - Call Forwarding/Do Not Disturb 7Yes. Do Not Disturb Override C]Yes, CO Forward Mode CO Transfer Mode Forded Account Code Mode . BSSKIHCA BSSOHCA Deny Executive Busy Override Executive Busy Override Deny Station Lock Walking Station Maintenance Capability ARSbcal Access - - drunk Group kcess (0 to 255) ONo q No JYes. UNo Dyes, ONo Dyes, q NO 0 Yes,UNo q Yes. q No 0 Yes,ONo ayes, ONo 0 Yes,ONo 0 Yes,ONo q Yes, ONo - .’ , 0 WIRSTR. ~NO R S T R No ACCS q Set Data Item $ecial carrier 4CCSS Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Group Group Group Group Group Group Group Group Group Group Group Group Group Group Group Group q 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 q jYes. 0 No aYes, 0 N o aYes, 0 N o Yes, No q q [!“’ i !’ mYi:: 0 Nz ]Yes. 0 No Yes, 0 No ayes, 0 N o ayes. 0 N o Yes, 0 No ayes, 0 N o c]Yes, ONo ayes. 0 N o q q q EQAl Yes,aNo OCCl uYes.nNo EQA2 0 Yes.0 No OCC2 0 Yes, 0 No EOA3 0 Yes.0 No OCC3 0 Yes. ~NO EQA4 Yes.0 No OCC4 0 Yes, 0 No q itation Paging kCE..S External Paging 3-12 q q q q q Yes. q No PAGl [IIYes,ONo PAGS Yes,ONo PAG2 Yes,nNo PAG6 Yes.uNo PAG3 Yes,nNo PAG7 aYes. No PAG4 fJYes.ONo PAG8 jYes,C]No q q External paging 1 External paging 2 ayes, 0 No Ciass of Service No. 15 Set Data Item Tc. ?estrictton Level (Day) T o . ?estriction Level (Night) Vz: D i a l i n g D i g i t s Ca Forwarding/Do Not Disturb CC Forward Mode CC T r a n s f e r M o d e Fazed A c c o u n t C o d e M o d e BSS/OHCA BSS0HCA D e n y Executive Busy Override Executive Busy Override Deny Station Lock Station Maintenance Capability AtWLocal Access - ( 0 1 - Cc ‘ J o t D i s t u r b O v e r r i d e Wafking - Item (01 to 16) t o - drunk Croup kU?SS 1 6 ) - (Oto a Yes, q No 0 Yes, q No Dyes. q No q Y&, ONo q Yes, ONo q Yes, ONo 0 Yes, q ]No q Yes, ONo q ]Yes. UNo 0 Yes,(7No q Yes, ONo q Yes, q No 0 W/RSTR. q 255) $ecial Carrier kU?SS ;tation P a g i n g ruxss No RSTR External Paging 0 No ACCS Set Data Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Grc,o Gro,;, Grc..p Grc,o Grc,p Grc,p Group Grcup Group Group Grotip Trunk Group Trunk Group Set Data Tdl Restriition Level (Night) ( 0 1 Max. Dialing Digits - call Forwardin@o Not Disturb Do Not Disturb Override Co Forward Moda CC Transfer Made Forced Account Code Mode BSSX)HCA BSSMCA Deny Executive Busy Override Executive Busy Override Deny station Lock Walking Station Maintenance Capability ARSRocal Access q q HE* BE aYes: 0 N o aYes, No aYes. c] N o External paging 1 External paging 2 &t:: 8:: _- Item - C]Yes. C]No Yes. No OYes. UNo OYes. 0 N o q q Yes.ONo q Yes. c] No c]Yes, 0 N o q Yes. 0 No Trunk Group aYes. 0 N o Trunk Group 15 q Yes. 0 No Trunk Group 1 6 q Yes. 0 No EQAl C?Yes.nNo OCCl q Yes,uNo EGA2 @ Yes.0 No OCC2 0 Yes, q No EGA3 c Yes..uNo OCC3 c]Yes, ONo EOA4 0 Yes.O No OCC4 0 Yes, q No PAGl GYes.nNo PAGS q Yes.aNo PAG2 [3Yes,uNo PAG6 q Yes,ONo PAG3 nYes,ONo PAG7 ayes. ONo PAG4 q Yes.uNo PAG8 ayes, [7No Class of Service No. 16 Td Restriitbn Level (Day) Cl G2 53 C4 05 06 07 08 09 10 11 12 13 14 - (01 to 16) t o - 1 6 ) - Trunk Group Access (0 to 255) ayes. q No q Yes. q No 0 Yes, q No 0 Yes,ONo 0 Yes,[7No q Yes, q No q Yes, q No 0 Yes,~NO 0 Yes, q No n Yes, q No 0 Yes,ONo c]Ye.s. q No 0 W/RSTR. ONo RSTR 0 No ACCS Set Data item Trunk Group 01 Trunk Group 02 Trunk Group 03 Trunk Group 04 Trunk Group 05 Trunk Group 06 Trunk Group 07 Trunk Group 08 Trunk Group 09 Trunk Group 10 Trunk Group 11 Trunk Group 12 Trunk Group 13 Trunk Group 14 Trunk Group 15 Trunk Group 16 q Yes. 0 No [7Yes, 0 N o ayes, 0 N o Yes, 0 No c]Yes, No ayes, El Yes, 0:: ayes, 0 N o ayes, 0 N o Yes, 0 No ayes. 0 N o c]Yes, 0 N o Yes. 0 No ayes, 0 N o ayes, 0 N o Yes, 0 No q q spedal carrier Access q q q q q EQAt Yes,ONo EUA2 Yes,n No EQA3 0 Yes,uNo EQA4 0 Yes.0 No q q q q q OCCl Yes,C]No OCC2 0 Yes, 0 No OCC3 0 Yes, ONo OCC4 ayes. ONo Station Paging Access PAGl PAG2 PAG3 PAG4 External Paging External paging 1 aYes. ONo External paging 2 aYes, 0 No 3-13 Yes.mNo PAGS aYes.ONo Yes,nNo PAG6 Yes,ONo Yes,ONo PAG7 aYes. ON0 Yes.nNo PAG8 Yes.~No q q k Class of Service No. 17 Item Trunk Group Gail For,sa~: -3 3c NC: 5 -‘u.~ D o N o t Disrura -: Yes INC .: Yes. ~No Cvewze CO Forward Mode DYES. ~No CO Transfer Mode XYes. j?No BSSKIHCA Deny ,I Yes, q No JYes, q No 3Yes. q No Executive Busy Override aYes. Forced Account Code Mode BSSKIHCA Executive Busy Override Deny ONo 7 Y e s , ONo IO ‘OYes. NO Station Lock Walking Station q Yes, NO Maintenance Capability aYes, ARS/Local Access q ONo WRSTR, (7No RSTR 0 No ACCS Set Data Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Group Group Group Group Grcup Group Grcup Group Group Trunk Group Trunk Group 01 02 03 04 05 06 07 08 09 10 11 aYes. aYes. aYes. C]Yes. q 0 N o 0 N o ~No [? N o R 8;: Yes: No Yes. No Yes. c] No q q q q q Yes, q ]No q Yes. 0 No Trunk Group 12 q Yes. 0 No Trunk Group 13 ayes, 0 N o Trunk Group 14 q Yes, 0 No Trunk Group 15 q Yes. 0 No Trunk Group 16 q Yes, 0 No EQAl [?Yes,ONo OCCl q Yes,nNo EQA2 @ Yes,0 No OCC2 0 Yes, q No EQA3 @ Yes,0 No OCC3 0 Yes, q No EGA4 0 Yes.0 No OCC4 q Yes, q ]No PAGl CiYes.nNo PAG5 q Yes.[7No PAG2 GYes,nNo PAG6 q Yes, q No PAG3 q Yes,ONo PAG7 Dyes. ONo PAG4 q Yes,nNo PAG8 q Yes.ONo External paging 1 q Yes, No External paging 2 Dyes, 8 No Class of Service No. 18 Set Data Item ( 0 1 Toll Restriction Level (Day) Toll Rastriition Level (Night) ( 0 1 Max. Dialing Digits - Call Forwarding/Do Not Disturb Da Not Disturb Override CO Forward Mode CO Transfer Mode Forced Account Code Mode BSSCHCA BSSKIHCA Deny Exacutive Busy Override Executive Busy Override Dany station Lock Walking Station Maintenance Capability ARSRocal Access . - t o t o - 1 6 ) drunk Group kO%S 1 6 ) (0 10 255) Dyes, q No aYes, q No Dyes, [7No q Yes, q No q Ye.s.ONo q Yes. ONo aYes, q No ayes. [7No [7Yes. q No q Ye.s.~NO ayes, ONo q Yes, ONo 17 W/RSTR, q 0 No ACCS Item $eCial Carrier kf%?SS ;tatidn Paging iCCSS NO RSTR Ixtemal Paging Set Data Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Group 01 Group 02 Group 03 Group 04 Group 05 Group 06 Group 07 Group 08 Group 09 Group 10 Group 11 Group 12 Group 13 Group 14 Group 15 Group 16 q Dyes, 0 N o Yes. No Yes. 0 No Yes, 0 No q q q q 82 8:: ]Yes: 0 No ayes, 0 N o ayes, 0 N o ayes, 0 N o ayes, 0 N o aYes, No Yes, 0 No 0 Yes, 0 No Yes, [7 No ayes. 0 N o q q q q q q q q PAGl q Yes,ONo PAG5 q Yes.nNo PAG2 q Yes.[7No PAG6 c]Yes. q No PAG3 [7Yes,nNo PAG7 q Yes. ONo PAG4 f-JYes,ONo PAG8 q Yes, ~NO External paging 1 q Yes. q No EQAl Yes.nNo EQA2 0 Yes.0 No EQA3 0 Yes,0 No EQA4 0 YesQ No OCCl Yes.ONo OCC2 0 Yes, ONo OCC3 Yes, No OCC4 Yes, ONo External paging 2 Dyes, 0 No 3-14 Class of Service No. 19 Item Set Eata - T a Restriction Level (Day) TO;I R e s t r i c t i o n L e v e l ( N i g h t ) ( M a x D i a l i n g DIgits :: Ca;l Forwardlng!Do Go Not Disturb Not Disturb 0 1 (01 :,^ ‘“) :: ‘ 3 .3 aYes. Trunk Group ACCSSS ) 2531 X? F o r w a r d M o d e CO Transfer Mode Forced Account Code Mode BSS0HCA BSSKIHCA Deny Executive Busy Override Executive Busy Override Deny Station Lock Walking Station Maintenance Capability A RSILocaf Access Trunk Group 01 Trunk Group 02 Trunk Group 03 Trunk Group 04 Trunk Group 05 EN2 q Yes. CN: C]Yes. CNc 0 Yes,EN: aYes, ENo q Yes, ENc c] Yes, q Nc aYes, @No OYes. CNo aYes, NO aYes. q N= q Yes, UNo Override Set Data Item Special aYes. 0 N o g2 El: q Yes. 0 No ZYes. c N o q Yes. 0 No q T:iz: ~~~~~ E”7 Trunk Group Of3 Trunk Group 09 Trunk Group 1 0 0 Yes’ 0 No Yes: 0 No aYes, 0 N o ayes., No Trunk Group 11 Trunk Group 12 Trunk Group 13 Trunk Group 14 Trunk Group 15 Trunk Group 16 C]Yes, c] N o Yes, 0 No Yes. c] No Yes, 17 No Yes. c] No Yes, 0 No q q q q q q Carrier Access jlalion Paging 4ccess 0 WIRSTR, ~NO RSTR 0 No ACCS External Paging L External paging 1 Externai paging 2 Y e s , ONo Y e s , ONo Class of Service No. 20 Item ( 0 1 roll Restriition Level (Day) Toll Restriction Level (Night) ( 0 1 Max. Dialing Digits - Xl Forwarding/Do Not Disturb ayes. XI Not Disturb Override 20 Forward Mode ZO Transfer Mode ‘orcad Account Code Mode 3SSiOHCA 3SSKIHCA Deny Executive Busy Override Executive Busy Override Deny Station Lock Walking Station Maintenance Capabilii A FIShcal Access Item Set Data . - t o t o 16) 76) frunk Group hCPSS - (C to 255) ONo q Ye.s. q No q Yes, NO q Yes. q ]Nc aYes. q No q Yes, ~NO [7Yes, q N3 aYes, NO q Yes, q No Ryes. ONo ayes, q No q Yes, q jNo c] W/RSTR. r]No RSTR 0 No ACCS Set Data Trunk Group 01 Trunk Group 02 Trunk Group 03 Trunk Group 04 Trunk Group 05 Trunk Group 06 Trunk Group 07 Trunk Group 08 Trunk Group 09 Trunk Group 10 Trunk Group 11 Trunk Group 12 Trunk Group 13 Trunk Group 14 Trunk Group 1 5 [r]Yes. [ [ [ [ [ [ [ [ [ [ [ [ [ ~NO IYes. ONo Special Carrier kcess q q q station Paging kcess PAGl Yes,O No PAG2 [7Yes,ONo PAG3 Yes,ONo PAG4 Yes,nNo External Paging External paging 1 ]Yes, No External paging 2 aYes, [7 No 3-15 q q ;/j I /ii ii i/ !I /I CO Fowlcar:? ttode CO Transfer Mode Forced Account Co& Mode BSSJOHCA BSSOHCA Deny Executive Busy Overrde Executive Busy Override Deny Station Lock Walking Station Maintenance Capability ARS/Locat Access -‘a Yes. q No aYes. q No eyes, UNo aYes, ONo q ]Yes,UNo ayes, q No aYes, q No [7Yes, [7No eyes, q No eyes, q No 0 WIRSTR, q Set Data Item iv I/( / drunk G r o u p 4ccess Trunk Group Cl Trunk Group C2 Trunk Group 03 Trunk Group 04 Trunk Group 05 Trunk Group 06 Trunk Group 07 Trunk Group 08 Trunk Group 09 Trunk Group 10 Trunk Group 11 Trunk Group 12 !Trunk Group 13 Trunk Group 14 iTrunk Group 15 jTrunk Group 16 Special Carrier kcess q IYes, 0 N O IYes. ONo ‘IYes, 0 No 1Ye.s. NO q $z: q aYes. aYes, Yes: 0 No 0 N O 0 N O eyes, q No aYes. 0 N q Yes, 0 No q Yes. 17 No q Yes, 0 No O ayes, 0 N o q q i EQAl Yes.nNo EOA2 0 Yes.0 No EOA3 0 Yes.0 No EOA4 Yes.0 No OCCl Yes.nNo OCC2 Yes. ONo OCC3 0 Yes. ONo OCC4 0 Yes. ONo q q q q q q q No itation Paging tcess PAGl [7Yes,nNo PAG5 Yes..nNo PAG2 Yes,ONo PAG6 Yes.ONo PAG3 Yes,aNo PAG7 Yes. No PAG4 (7Yes.nNo PAG8 ayes, No External Paging External paging 1 aYes. External paging 2 Dyes, 0 No No RSTR 0 No ACCS pi q q Class of Service No. 22 Toll Restriction Level (Day) ( 0 1 t o 1 6 ) Toll Restriction Level (Night) ( 0 1 Max. Dialing Digits - Call Forwarding/Do Not Disturb q Yes, 0 No Do Not Disturb Override ayes, ONo t o - - CO Transfer Mode Forced Account Code Mode 0 Yes, 0 No BSSOHCA q Yes, UNo BSSKIHCA Deny Executive Busy Override Executive Busy Override Deny Station Lock Walking Station Maintenance Capability ARSRd Access ‘c]Yes, Trunk Group k%.BS 1 6 ) q Yes, UNo Dyes. q NO CO Forward Mode item Set Data Item (0 to 255) q Yes, q Yes, q Yes, ayes, q Ye.s. 0 No ACCS Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk I: I: ONo q No q No q No q No q No 0 W/RSTR, q I 3pecial carrier kcess Set Data Group 01 Group 02 Group 03 Group 04 Group 05 Group 06 Group 07 Group 08 Group 09 Group 10 Group 11 Group 12 Group 13 Group 14 Group 15 Grow 16 [ Y e s , UNo [ [ [ [ [ [ [ [ [ [ [ [ [ [ r EQAl [7 Yes,nNo EQA2 [7 Yes.0 No ECU3 0 Yesa No EQA4 0 Yesa No itation Paging kcess 3-16 Paging OCC2 0 Yes. 0 No OCC3 0 Yes, 0 No OCC4 [7 Yes, ONo S PAG5 Yes, ONo Yes, PAG6 PAG7 Yes. ONo PAG8 ayes. ONo q No RSTR External Yes, q No Yes,UNo Yes,~NO Yes, No Yes,8No Yes,ONo Yes, q No Yes, q No Yes,ONo Yes,[7No Yes,ONo Yes,UNo Yes,UNo ,Yes. ONo Yes, q No OCCl q Yes,ONa External paging 1 External paging 2 q q q q No Yes. No Yes. 0 No Class of Service No. 23 / Item i Toll Restriction Level ’ T o l l Restriction (Day) Level (Night) M a x . D i a l i n g Digits Call Forwarding Do Not Disturb Override Do Not Disturb CO Forward Mode CO Transfer Mode Forced Account Code Mode BSSKIHCA BSOHCA Deny Executive Busy Override Executive Busy Override Deny Station Lock Walking Station Maintenance Capabifii A RSbxaf Access i Set Data I ( 0 1 t o ( 0 1 rrur* Group 1 6 ) t o i4CfZSS 1 6 ) ---(0 Item to 255) aYes. q No 0 Yes. q No q Yes. ONo 0 Yes,ONo ayes, CNo q Yes, ONo OYes, ONo OYes, ONo q Yes, ONo 0 Yes, q No ayes. ONo ayes, [7No 0 WRSTR, q !$ecial I kcess sitation A &2SS No RSTR Carrier Paging IExternal Paging t 0 No ACCS Set Data Trunk Group 01 ayes, Trunk Group 02 Trunk Group 03 Trunk Group 0 4 Trunk Group 05 Trunk Group 06 Trunk Group 07 Trunk Group 08 Trunk Group 09 Trunk Group 10 Trunk Group 11 Trunk Group 12 Trunk Group i 3 Trunk Group 14 Trunk Group 15 Trunk Group 16 0 N o 12 1:: Yes: No Yes, 0 No Yes. 0 No aYes. 0 N o Yes, 0 No Yes. 0 No [7Yes, 0 N o [7Yes, 0 N o aYes, 0 N O Yes, No q Yes. 0 No aYes, CNo q Yes. 0 No q q q q q q q q ECAl Yes.ONo EQA2 0 Yes.0 No ECU3 c] Yes.0 No EOA4 0 Yes,0 No q CCC1 q Yes,nNo OCC2 0 Yes, ~No OCC3 0 Yes, ]No OCC4 Yes, ~NO q q q PAGl Yes.aNo PAG2 Yes,uNo PAG3 Yes.ONo PAG4 /-‘JYes,/-JNo q q PAGS q Yes, q No PAG6 ayes. ONo PAG7 q Yes, ~NO PAGE q Yes. ONo External paging 1 aYes, External paging 2 Yes, q No INo Class of Service No. 24 item Restriion ( 0 1 t o 1 6 ) Toll Restriction Level (Night) ( 0 1 t o 1 6 ) Max. Dialing Digits - Call Forwarding/Do Not Disturb 0 Yes, Do Not Diiturb Override 0 Y e s , ~NO CO Forward Mods 0 Y e s , ONo CO Transfer Mode ayes. q iuo Forced Account Code Mode 0 Yes, 0 No Toll Level (Day) - - BSSQHCA Deny Executive Busy Ovsrride 0 Y e s . ~NO Executive Busy Ovarride Deny 0 Yes, Station Lock 0 Y e s , ONo Walking Station 0 Y e s , CNo Maintenance Capability ARS/bxaf Access drunk Group kcess (0 to 255) 0 No p Yes. q N0 q Yes. ONo BSSf#fiCA Item Set Data 0 No ACCS Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Group 01 Group 02 Group 03 Group 04 Group 05 Group 06 Group 07 Group 08 Group 09 Group 10 Group 11 Group 12 Group 13 Group 14 Group 15 Group 16 q Ye.s. 0 No ayes. 0 N o Dyes, 0 N o Yes. No Y e s , ONo B Yes. No Yes, 0 No Yes, No ayes, 0 N o aYes. 0 N o ayes, 0 N o Yes. 0 No 0 Yes, 0 No Yes. [3 No Yes, No q q Yes, q No q q q q q q q q q $ecial Carrier 4CCPSS 0 No q Yes, ONo 0 WRSTR, q Set Data Ltation Paging ccess NO RSTR Slernal Paging 3-17 External paging 1 Dyes, 0 No External paging 2 Yes, [7 No q Class of Service No. 25 Set Data Trunk Gro,2 GrcI3 Trunk Gro,3 Trunk Grc,3 Trunk Gro,2 Trunk Gro-3 Trunk Gro;D Trunk Group Trunk Group Trunk Group Trunk Group Trunk Group 01 02 03 04 05 06 07 08 09 10 11 12 iYes. =No ‘Yes, -No :No 7Yes. ZYes. ~No lYes. -NC ~No j Yes. ~NO IYes. IYes. ~No IYes, ji N o IYes. ~No IYes, a N o aYes. g N o Group 13 aYes. 0 N o Group 14 Group 15 Group 16 c]Yes. 0 N o gYes, 0 N o 3 Yes, 0 No i Trunk cc Fcr*arc !.‘- z: 0 CO Transfer Lb:+ aYes. F o r c e d A c c o u n t We M o d e BSSOHCA BSSOHCA CenT Exeahve Busy Override Executive Busy Override Deny Station Lock Walking Station Maintenance Capability ARS/Local Access Y e s , CNo ~No Dyes, q No 0 Yes, q No q Yes, q ]No (7Yes. ~NO aYes, q No q Yes, q No Dyes, q No ayes, [7No 0 W/RSTR, q Trunk Trunk Trunk Trunk Special Carrier ACna% Station Paging Access No RSTR . External Paging 0 No ACCS External paging 1 External paging 2 Class of Service No. 26 item Set Data Item (01 to 16) Trunk Group Access Toll Restriction Level (Day) - - Toll Restriction Level (Night) - - (01 to 16) Max. Dialing Digits - Call Forwarding/Do Not Disturb ayes, Do Not Disturb Override CO Forward Mode CO Transfer Mode Forced Account Code Mode BSSOHCA BSSKMCA Deny Executive Busy Override Executive Busy Override Deny Station Lock Walking Station Maintenance Capability ARSRocal Access - - (0 to 255) ~NO q Yes, q NO q Yes, q No q Yes, ~NO Dyes, q No q Yes, ~NO ayes, q No Dyes, q No 0 Yes, q NO Dyes. ONo ayes. q NO aYes. q No 0 WIRSTR, q 0 No ACCS No RSTR Set Data Trunk Group 01 Trunk Group 02 Trunk Group 03 Trunk Group 04 Trunk Group 05 Trunk Group 06 Trunk Group 07 Trunk Group 08 Trunk Group 09 Trunk Group 10 Trunk Group 11 Trunk Group 12 Trunk Group 13 Trunk Group 14 Trunk Group 15 Trunk Group 16 q q q q Yes, 0 No Yes. 0 No Yes, No ayes. [7 N o q 82 El!: Ye.s: c] No Dyes. 0 N o Yes. [7 No C]Yes, 0 N o ayes. No ayes, 0 N o Yes, No Ye.s. c] No ayes, No ayes. 0 N o q q q q q q q Special Carrier Access EQAl Yes,mNo OCCl [7Yes,nNo ECU2 0 Yes.0 No OCC2 0 Yes, No EC&U 0 Yes,nNo OCC3 0 Yes, ONo EQA4 0 Yes.0 No OCC4 0 Yes, No Station Paging Access PAGl PAG2 PAG3 PAG4 External Paging External paging 1 Yes, 0 No External paging 2 Dyes. [7 No 3-18 q q q q q q Yes.nNo Yes.ONo ]Yes,ONo Yes.nNo q q PAG5 ]Yes.nNo PAG6 ayes. ONo PAG7 ayes. No PAG8 aYes. ]No q q Class of Service No. 27 item Set Data - (01 to 16) - (01 to 16) Toll Restriction Level (Night) - Max Dialing Digits - C a l l F o r w a r d i n g / D o Net D i s t u r b 0 Yes. Toll Restriction Level (Day) CO Forward Mode 0 Y e s , ~No Mode BSWHCA BSWHCA Deny Executive Busy Override Executive Busy Override Deny Station Lock Walking Station Maintenance Capability AlWLocal Access Set Data Trunk Trunk Trunk Trunk Trunk Group Group Group Group Group t:iZZ Trunk Trunk Trunk ~:~~~ Group Group Group 01 02 03 04 05 ~No Dyes. F o r c e d A c c o u n t Code Trunk Group Access - (0 to 255) - Do Not Disturb Override CO Transfer Mode Item i”7 08 09 10 Trunk Group 1 1 Trunk Group 12 ~No q Yes. NO Dyes, q No Dyes, q No q Yes, [?No 0 Yes,ONo q Yes. q No aYes. q No q Yes. q No q Yes, q No Trunk Group 13 Trunk Group 14 Trunk Group 15 Trunk Group 16 0 W/RSTR. nNo R S T R 0 No ACCS q q Yes. E No q Yes.CNo aYes. UYes, CNo E N o B2 Dyes.1 aYes. aYes, hl: p No E N o 0 N o Yes, m No ayes. No aYes. No q q q Dyes, c] N o ayes. 0 N o [7Yes, 0 N o ayes, 0 N o q Special Carrier Access EQAl Yes,rNo EQA2 0 Yes,m No EQA3 0 Yes,c No EOA4 0 Yes.p No Station Paging 4ccess PAGl CjYes.pNo PAG5 Yes.[7No PAG2 Yes,ENo PAG6 ayes, NO PAG3 Yes,ENo PAG7 Dyes. ONo PAG4 Yes.C:No PAG8 Yes, No External Paging OCCl Yes.uNo OCC2 0 Yes, ONo OCC3 (7 Yes, ]No OCC4 0 Yes, ONo q q q q q q External paging 1 E x t e r n a l p a g i n g 2 FJ::: q q 8:: Class of Service No. 28 Item Toll Res&iciii Level (Day) Set Data ( 0 1 l o item drunk Group 1 6 ) 4O%S Toll Restriction Level (Night) ( 0 1 t o 1 6 ) Max. Dialing Digits - - - (0 to 2 5 5 ) Call Forwarding/Do Not Disturb 0 Yes, 0 No CO Transfer Mode 0 Yes, q No 0 Yes, q NO 0 Yes, q No Forced Account Code Mode 0 Yes, 0 No Do Nof Disturb Override CO Forward Mode BSS#lCA .oYes. q No BSSKXCA Deny 0 Y e s , ONo Executive Busy Override ayes. Executive Busy Override Deny q Station Lock 0 Y e s , [7No Walking Station Maintenance Capability AfWLocal Access Yes, ONo SpC!CidCarrier kC43S.S [7 No 0 Yes, q No ayes. q No 0 W/RSTR. q 0 No ACCS itation Paging kU?SS No RSTR External Paging 3-19 S e t Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Group 01 Group 02 Group 03 Group 04 Group 05 Group 06 Group 07 Group 08 Group 09 Group 10 Group 11 Group 12 Group 13 Group 14 Group 15 Group 16 q Dyes. 0 N o aYes. 0 N o Yes. 0 No Yes, 0 No q q 82 8:: Yes: No aYes, 0 N o 0 Yes, No aYes, 0 N o aYes, No Yes, 0 No Ye-s. 0 No Yes. 0 No ayes. NO aYes, 0 N O q q q q EOAl Yes,ONo ECU2 c] Yes,[? No EQA3 0 Yes,0 No EOA4 0 Yes,0 No q q q D a t a PAGI Yes,uNo PAG2 Yes,ONo PAG3 Yes,nNo PAG4 OYes.nNo q q q q q q q OCCl Yes.nNo OCC2 c] Yes, No OCC3 Yes,ONo OCC4 17 Yes, ONo PAG5 ayes. ONo PAG6 Yes.ONo PAG7 [7Yes. ONo PAG8 Yes,nNo q q q Yes. q External paging 1 No External paging 2 c]Yes, [7 NO P Class of Service No. 29 Item Set Data -_>. =est:-:: ;c Le.fe: Iay) -__. =estr~*~zn Level ;Plight) -- (01 to 16) ( 0 1 1 6 ) ‘.’ is 2.2 r -: ;tys / -2 Tms~~~ 0 15 Do P:ot Disturb 1,: ‘.ot GI->;L~J Overrae ^_ _ -owed M o d e ‘s 2 Transfer Fccced Mode Account Code Mode BSSKJHCA BSS0HCA Deny Executive Busy Override Executive Busy Override Deny Station Lock Walking Station Maintenance Capability ARShcal Access t o ;1, ! Trunk Group ; Access i (0 to 255) Y e s , ~No q Yes, flNo q Yes. ONo 0 Yes,UNo q Yes, q No q Yes, q No q Yes, ONo q Yes, q No q Yes, ONo OYes. ONo [7 Yes, q No aYes. q )No 7 WEtSIR. ~NO R S T R 7 No ACCS Set Data Item : Trunk Gram Trunk GroLa Trunk GroL3 Trunk GroLa Trunk Grot,a Trunk Gram Trunk Gram Trunk Grout Trunk Groti3 Trunk Group Trunk Group Trunk Group Trunk Group Trunk Group TrunkGroup 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 Trunk Group 16 Sped Carrier Access Station Paging Access External Paging q q q PAGl q PAG2 q PAG3 q q Yes. 0 No q Yes, 0 No q Yes. q No q Yes. 0 No q 82 8:: Yes: 0 No q Yes.ONo q Yes, 0 No q Yes, 0 No q Yes. 0 No C]Yes. q No q Ye.s. 0 No q Yes. 0 No q Yes. q No q Ye.s. 0 No EQAl Yes,uNo OCCl flYes.nNo EQA2 Yes.uNo OCC2 0 Yes, ONo EOA3 0 Yes.0 No OCC30 Yes, No EOA4 Yes,O No OCC4 c] Yes, 0 No q q q ]Yes,nNo PAG5 Yes.ONo Yes,uNo PAG6 Dyes. flNo Yes,ONo PAG7 Yes, No PAG4 /JYes.fJNo PAG8 Dyes. ONo External paging 1 External paging 2 q q No Yes, 8 Y e s , ONo Class of Service No. 30 Item Tdt Restriction Level (Day) Set Data - Tdl Restriction Level (Night) - Max. Dialing Digits - Call Forwarding/Do Not Disturb Do Not Disturb Override CO Forward Mode CO Transfer Mode Forced Account Code Mode BSSKIHCA BSSiCHCA Deny Executive Busy Override Exeartivs Busy Override Deny Station Lock Walking Station Maintenance Capability ARE&cat Access - (01 to 16) - (01 to 16) - Item Trunk Group 4CCSS - (0 to 255) q Yes. ONo 0 Yes,UNo q Yes, q No 0 Yes,NO 0 Yes,ONo ayes, q No c] Yes,~NO ayes. ONo q Yes, ONo aYes. ONo ayes. q ]No q Yes. q ]No [7 W/RSTR, ONo R S T R 0 No ACCS sp@cial carrier kCX3SS Man Paging CCQSS External Paging 3-20 Set Data Trunk Group 01 Trunk Group 02 Trunk Group 03 Trunk Group 04 Trunk Group 05 Trunk Group 06 Trunk Group 07 Trunk Group 08 Trunk Group 09 Trunk Group 10 Trunk Group 11 TrunkGroup 12 Trunk Group 13 Trunk Group 14 TrunkGroup 15 Trunk Group 16 q ayes. 0 N o [7Yes, 0 N o ayes. 0 N o OYes. No q El;::* 8:: Yes: 0 No Dyes, 0 N o 0 Yes, 0 No [7Yes. 0 N o Yes. 0 No ayes. No ayes, 0 N o ayes, 0 N o Ryes, No ayes, 0 N o q q EOAl Yes,nNo ECU2 [7 Yes.0 No EOA3 0 Yesa No ECU4 [7 Yes.0 No q q q q q q OCCl Yes.ONo OCC2 [7 Yes, ONo OCC3 c] Yes, ONo OCC4 c] Yes, 0 No q q q q q External paging 1 q Yes. q No External paging 2 q Yes. 0 No PAGl Yes.ONo PAG2 Yes.nNo PAG3 Yes,nNo PAG4 [7Yes,ONo PAG5 Yes.[7No PAG6 Yes.(7No PAG7ayes. No PAG8 Yes. No Class of Service No. 31 Item i T o : qestrction Level (Day) To, 7estriction Level (Night) M+I Dialing Diqts Ca:’ =orwardmg DO Not Disturb Set Data -- (01 to 16) ( 0 1 1 6 ) t o - - - (0 to 2 C Yes, BSSQHCA Deny Exdive Busy Override [7 ‘dot Disturb Override C O =orward Mode CO Transfer Mode Forced Account Code Mode BSSOHCA Exeahve Busy Override Deny Station Lock Walking Station Maintenance Capability ARShcai Access Trunk Group ~Access 5 q .Yes, q N0 0 Yes, q No q Yes, ONo aYes, q No Level (Day) 0 WRSTR, [7No R S T R 0 No ACCS Set Data ( 0 1 t o 1 6 ) Tot1 Restriction Level (Night) ( 0 1 t o 1 6 ) Max. Dialing Digits - Call Forwarding&b Not Disturb 0 Y e s , ONo Do Not Disturb Override CO Forward Mode CO Transfer Mode Faced Account Code Mode BSSOHCA BSSKIHCA Deny Exacutive Busy Override Executive Busy Override Deny Station Lock walking station Maintenance Capability ARSRocal Afmss - - ayes, q No ayes, q No ayes. C]No 0 Yes,DNo ,a Yes,ONo c]Yes, q No ayes, ONo Dyes, ONo q Yes, UNo q Yes, ONo Dyes. ONo [7 W/RSTR, q 0 No ACCS Group Group Group Group Group q Yes.@No OYes. q No @Yes, q No 01 02 03 04 05 aYes, c] N o r Trunk Group 08 Trunk Group 09 Trunk Group 10 Trunk Group 11 aYes, Dyes, Trunk Group 12 Trunk Group 13 Trunk Group 14 Trunk Group 15 Trunk Group 16 =Yes, q q aYes. No No Yes. 0 No Yes. 17 No q nNo 0 N o [7Yes, 0 N o aYes. No Yes, 0 N O q q q Special Carrier Access EOAl CjYes,ONo OCCl ayes. No EGA2 0 Yes.0 No OCC2 0 Yes. 0 No EQA3 0 Yes,0 No OCC3 0 Yes, 0 No EOA4 0 Yes.0 No OCCP 0 Yes, 0 No Station Paging PAGl PAG2 PAG3 PAG4 GCSSS Class of Service No.32 Tdl Rest&ion Trunk Trunk Trunk Trunk Trunk fJYes.1 Yes, UNo Item Set Data ~~~~~ ~~“o~“, “0; a;::- qai: q N0 ) CNo q Yes. q No 0 Yes.ONo q Yes. ONo Dyes, [7No 0 Yes,ONo [7Yes. ONo Da 5 Item External Paging 11 q q q q (0 to 255) r I Special Carrier Access PAG5 PAG6 PAG7 PAG8 External paging 1 aYes. ONo External paging 2 Yes, 0 No q Set Data Item Trunk Group Access q Yes,ONo q Yes. nNo q Yes, q No q Yes, q ]No Yes.nNo Yes,nNo ]Yes,nNo Yes.uNo Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Group Group Group Group Group Group Group Group Group Group Group Group Group Group Group Group q 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 q Yes. 0 No Dyes. 0 N o q Yes. 0 No Dyes, 0 N o BE 8~: Yes: 0 No Yes. 0 No Yes, 0 No ayes. 0 N o Yes, 0 No Yes. 0 No Yes, 0 No Ryes, 0 N o Yes, 0 No c]Yes, 0 N o q q q q q q q EGA1 Yes.ONo EQA2 0 Yes.0 No EGA3 0 Yes.0 No EOA4 0 Yes,0 No q q q q Slalion Paging Access PAGl PAG2 PAG3 PAG4 External Paging External paging 1 ayes, ONo External paging 2 ayes, 0 No No RSTR 3-21 q q Yes.ONo Yes,nNo Yes,ONo Yes,/‘JNo q q OCCl ayes. No OCC2 0 Yes, ONo OCC3 c] Yes, No OCC4 0 Yes, ONo PAG5 PAG6 PAG7 PAG8 Yes,uNo Yes.nNo Yes. No Yes;ONo q q q SYSTEM-LOCAL ACCESS GROUP item Set Data Toll Restriction Le:?l Default Value -- 2 digits (01 to 16) 16 - 1 digit (1 to 8) 1 01 -- 2 digits (01 to 16) 01 02 -- 2 digits (01 to 16) blank 03 -- 2 digits (01 to 16) blank 04 -- 2 digits (01 to 16) blank 05 -- 2 digits (01 to 16) blank 06 -- 2 digits (01 to 16) blank 07 -- 2 digits (01 to 16) blank 08 -- 2 digits (01 to 16) blank 09 -- 2 digits (01 to 16) blank 10 -- 2 digits (01 to 16) blank 11 -- 2 digits (01 to 16) blank 12 -- 2 digits (01 to 16) blank 13 -- 2 digits (01 to 16) blank 14 -- 2 digits (01 to 16) blank 15 -- 2 digits (01 to 16) blank 16 -- 2 digits (01 to 16) blank Toil Restriction Tabre Local Access Trunk Group Hunt Sequence 3-22 SYSTEM-NUMBERING PLAN (l/4) No. item / Default ~V a l u-.e Set Data 1 1 st Hundred Block Extension - 2 2nd Hundred Block Extension ~- 1 or 2 digits (0 to 9) 3 3rd Hundred Block Extension - - 1 4 4th Hundred Block Extension - - 1 o r 2 digits (0 to 9) 5 5th Hundred Block Extbsion - - 1 to 9) - 6 6th Hundred Block Extension - - 1 or 2 dlgits (0 to 9) - 7 7th Hundred Block Extension - - 1 or 2 digits (0 to 9) - 8 8th Hundred Block Extension - - 1 or 2 digits (0 to 9) - 9 9th Hundred Block Extension - - 1 or 2 digits (0 to 9) - . 1 - or 2 or or d’gits (0 to 9 ) 2 digits (0 2 digits (0 t o 9) i 1 2 3 - 10 10th Hundred Block Extension - - 1 or 2 digits (0 to 9) - 11 11 th Hundred Block Extension - - 1 or 2 digits (0 to 9) - 12 12th Hundred Block Extension - - 1 or 2 digits (0 to 9) - 13 13th Hundred Block Extension - - 1 or 2 digits (0 to 9) - 14 14th Hundred Block Extension - - 1 or 2 digits (0 to 9) - 15 15th Hundred Block Extension - - 1 or 2 digits (0 to 9) - 16 16th Hundred Block Extension - - 1 or 2 digits (0 to 9) - 17 Operator Call (General) - - - - 1 t o 4 digits (0 t o 9, *, #) 0 18 Operator Call (Specific) - - - - 1 t o 4 digits (0 t o 9. *, #) 3 19 AFWLocal - - - - 1 t o 4 digits (0 to 9, *, #) 9 20 Trunk Group 01-08 Access - - - - 1 t o 4 digits (0 to 9, *, #) 81 21 Trunk Group 09-l 6 Access - - - - 1 t o 4 digits (0 to 9, *, #) 82 22 Trunk Group 17-24 Access - - - - 1 t o 4 digits (0 to 9, *, #) 83 23 Speed Dialing-System - - - - 1 t o 4 digits (0 to 9, *, #) ‘1 24 Speed Dialing-Station - - - - 1 t o 4 digits (0 to 9, *, #) +2 25 Doorphone Call (i-4) - - - - 1 t o 4 digits (0 to 9, *, #) 40 26 External Paging - - - - 1 t o 4 digits (0 to 9, *, #) 41 27 Station Paging - - - - 1 t o 4 digits (0 to 9, *, #) 42 28 External Paging Answer - - - - 1 t o 4 digits (O’to 9, *, #) 43 29 Station Paging Answer - - - - 1 t o 4 digits (0 to 9, *, #) 44 30 Night Answer 1 - - - - 1 t o 4 digits (0 to 9, *, #) 45 31 Night Answer 2 - - - - 1 t o 4 digits (0 to 9. *, t) 46 32 Dial Call Pickup - - - - 1 t o 4 digits (0 to 9. *, #) 47 CO Line Access 3-23 SYSTEM-NUMBERING PLAN (214) No. Item Set Data 33 Directed Call Pickup _--- 34 Hold Extension Retrieve - ’ 35 j Redial - - - 1 - _--- Default Value to digits 4 (0 to 9. &, #) 48 1 to digits 4 (0 to 9. *, #) 49 1 to digits 4 (0 to 9, *, #) '3 36 External Feature Access - - - - 1 to 4 digits (0 to 9, +, #) 50 37 Account Code - - - - 1 to 4 digits (0 to 9. +, t) +# 38 Hold - - - - 1 to digits 4 (0 to 9, *, #) 51 39 Hold Retrieve 1 to 4 digits (0 to 9, *, #) 52 40 Call Park-System 1 to 4 digits (0 to 9, ?c, #) 53 41 Call Park Retrievtiystem 1 to 4 digits (0 to 9, l”, #) 54 42 Call 1 to 4 digits (0 to 9, *, #) 55 43 Call Park Retrieve-Station 1 to 4 digits (0 to 9, *, #) 56 44 Call Forwarding-All Call Set - - - - 1 to 4 digits (0 to 9, *, #) a+ 2 45 Call Forwarding-8usy - - - - 1 to 4digits (0 to 9, l”, #) &W ' 3 46 Call Fowarding-No Answer Set - - - - 1 to 4digits (0 to 9, *, #) *+4 47 Call Forwarding-To Trunk - - - - 1 to digits 4 (0 to 9. *, #) ?+uw5 46 Call Forwarding--Busy/No Answer - - - - 1 to 4 digits (0 to 9, *, #) u-u 6 49 Do Not Disturb Set 1 to 4 digits (0 to 9. *, #) WWl 50 Call Forwarding/Do --i- 1 to 4 digits (0 to 9. *, #) ##IO 51 Dial Call Pickup Deny Set - - - - 1 to digits 4 (0 to 9, *, #) 61" 52 Dial Call Pickup Deny Cancel - - - - 1 to digits 4 (0 to 9. *, #) 61# 53 Call Waiting Set --Pm 1 to digits 4 (0 to 9. *, #) 62" 54 Call Waiting Cancel - 1 to 4 digits (0 to 9. *, #) 62# 55 BSSIOHCA 1 to 4 digits (0 to 9. *, #) gp 56 BSS/OHCA - Park-Station - Set Not Disturb Cancel - - - - - - - - - Deny Set 1 to 4 digits (0 to 9. *, #) 57 Deny Cancel . Busy Override Deny Set - - - - 1 to 4 (0 to 9, *, #) digits 56 Busy Override Deny Cancel - - - - 1 to 4digits (0 to 9. *, #) 59 Data Line Security Set - - - - 1 to 4 digits (0 to 9. *, W) 60 Data Line Security Cancel - - - - 1 to 4 digits (0 to 9. *, #) 61 Pickup - - - - 1 to 4digits (0 to 9. *, #) 62 Pickup Dialing Set ---w 1 to 4digits (0 to 9. *, 1) 63 Pickup Dialing Cancel - Dialing Programming 3-24 - - - 1 to digits 4 (0 to 9. *, W) SYSTEM-NUMBERING PLAN (3/4) No. Item Set Data 64 Absent Message Set - 65 Absent Message Cancel ---__ 66 Timed Reminder Confirm 67 - Timed Reminder Set - - - - - - --~- Default Value 1 t o 4 digits ( 0 to 9, *, #) i4 1 to 4 digits ( 0 to 9. -, #) #4 1 t o 4 digits ( 0 to 9, *, #) ‘50 1 t o 4 digits ( 0 to 9. &, #) &51 68 j Timed Reminder Cancel - - - - 1 to 4 digits ( 0 t o 9, *, #) #5 69 /Voice Calling Mode Set - - - - 1 t o 4 digits (0 to 9. *, #) 67* 70 ‘Voice Calling Mode Cancel ---__ 1 t o 4 digits (0 to 9, *, 1) 67# 71 Voice Calling Deny Set - - - - 1 t o 4 digits (0 to 9, *, #) 68’ 72 Voice Calling Deny Cancel - - - - 1 t o 4 digits (0 t o 9, +, #) 68# - - - - 1 t o 4 digits (0 t o 9, *, #) 6’ - - - 73 Speed Dialing-Station Programming 74 Station Lock Set - 1 t o 4 digits (0 t o 9, +, #) “6 75 Station Lock Cancel -__-- 1 t o 4 digits (0 t o 9, *, #) #6 76 Walking COS Set - - - - 1 t o 4 digits (0 t o 9, *, #) *7 77 Walking COS Cancel - - - - 1 t o 4 digits (0 t o 9, *, #) #7 78 Walking Station Set - - - - 1 t o 4 digits (0 t o 9, +, #) +8 79 .Walking Station Cancel - - - - 1 t o 4 digits (0 t o 9. *, #) #8 80 Message Set - - - - 1 t o 4 digits (0 t o 9. jc, #) ‘9 81 Message Cancel - - - - 1 t o 4 digits (0 t o 9, *, #) # 82 Station Program Clear - - - - 1 t o 4 digits (0 t o 9, *, #) ### 83 (Reserve) 84 (Reserve) 85 Night Mode Set - - - - 1 t o 4 digits (0 t o 9. *, #) 70* 86 Night Mode Cancel - - - - 1 t o 4 digits (0 t o 9, *, #) 70# 87 - - - - 1 to 4 digits (0 to 9, *, #) 71++ 88 Night Service Manual Mode Set . Night Service Manual Mode Cancel - - - - 1 t o 4 digits (0 t o 9, *, #) 71# 89 Flexible Night Service - - - - 1 to 4 digits (0 t o 9. *, #) 72 90 Remote Station Lock Set - - - - 1 t o 4 digits (0 t o 9, l”, #) 73’ 91 Remote Station Lock Cancel - - - - 1 t o 4 digits (0 t o 9. *, #) 73# 92 Remote DND Set - - - - 1 t o 4 digits (0 t o 9. *, #) 74+ 93 Remote DND Cancel - - - - 1 t o 4 digits (0 t o 9, ic, #) 74## 94 Remote FWD Cancel - - - - 1 t o 4 digits (0 t o 9, +, #) 75 95 Remote FWD Cancel-One Time --~~ 1 t o 4 digits (0 t o 9. *, #) 76 3-25 SYSTEM-NUMBERING PLAN (4/4) l- NO. Item Set Data Default 1 Value 96 BGM Through External Paging - - - - 1 to 4 digits (0 to 9. *, #) 77 97 Busy Out Trunk - - - - 1 to 4 digits (0 to 9. *, #) 78’ 98 Unbusy Trunk - - - - 1 to 4 digits (0 to 9, *, #) 78# 99 OGM Record - - - - 1 to 4 digits (0 to 9. +, at) 791 100 OGM Playback - - - - 1 t o 4 digits (0 t o 9, *, #) 792 101 UCD Log In - - - - 1 t o 4 digits (0 t o 9, *, #) ‘ 0 102 UCD Log Out - - - - 1 t o 4 digits (0 t o 9, *, #I #O 103 (Reserve) 104 (Reserve) 105 (Reserve) 106 (Reserve) 107 (Reserve) 108 (Reserve) . 3-26 : SYSTEM-COMMUNICATION INTERFACE SIO No. 1 (Terminal) / i Item \JL-Code Set Data 0 Default ! Value / /---J 0 3aud Rate 0 110baud 0 150 baud 0 300 baud 0 600 baud 0 1200 baud 0 2400 baud [74800baud 9600 baud q Nord Length 0 7 bits c] 8 bits 7 Set Data ‘0 < C R > c] 1200 SIO No. 2 (SMDR) 0 n 0 q 0 7 bits [I1 8 bits Remote (Modem) / Default Value 1lObaud 1 5 0 baud 3 0 0 baud 600 baud 1200 baud 0 2400 baud 0 4 8 0 0 baud 0 9600 baud T I Set Data 0 q T Default Value cCR+LF> 0 300baud [71200baud 1200 300 7 8 0 Even ‘arity Mark 0 Even None 01 bit 1 Stop Bit 3-27 SYSTEM-SPEED DIALING-SYSTEM (119) -- -.7,: 3e -_j ire-7 Re:‘*lction Level) I ; 2 digits (00-l 6) 00: Normal 01: Restriction 02: R e s t r i c t i o n 03: R e s t r i c t i o n 04: R e s t r i c t i o n 05: R e s t r i c t i o n 06: R e s t r i c t i o n 07: R e s t r i c t i o n 08: R e s t r i c t i o n Dial Number (including CO access code) l Default value Selection of value 00 C9: 10: level-l ievel-2 level-3 level-4 level-5 level-6 level-7 level-8 ; 1: 12: 13: 14: 15: 16: Max. 32 digits consisting of numbers, P : Pause F : Flash [ : Start of secret numbers ] : End of secret numbers - : Hyphen Restriction Restriction Restriction Restriction Restriction Restriction Restriction Restriction level-9 level-l 0 level-l 1 level-12 level-l 3 level-l 4 level-15 level-l 6 *;# and marks below: Pressing the NEXT button shows next 14 numbers from the last number shown on the screen. Pressing the PREVKYJS button shows previous 14 numbers from the first number shown on the screen. Set Data Speed Dial Type No. ( T o l l Restriction Level) Dial Number (including CO access code) 001 002 003 004 005 I . 006 007 008 1 I 009 010 3-28 blank i SYSTEM-SPEED DIALING-SYSTEM (2/9) Set Data Speed Dial We /Q-J. ( T o l l Restriction Level) Dial Number (including CO access code) 011 012 013 I I I , 014 015 016 017 018 019 020 021 022 023 024 026 027 028 029 030 m 031 032 033 035 3-29 SYSTEM-SPEED DIALING-SYSTEM (319) Speed / Dial / No Set Data Type Dial Number (including I (Toll RestricI tion Level) 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 . 057 058 059 060 3-30 CO access code) SYSTEM-SPEED DIALING-SYSTEM (4/9) - -- Set Data Speed Cial Type Ko. (Toll Res:-c- j tion j Leve.1 I Dial Number (including CO access code) SYSTEM-SPEED DIALING=SYSTEM(5/9) Set Data Speed Dial Type No. (Toll Restriction Level) Dial Number (including CO access code) I 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 w ..- 103 104 105 106 107 108 109 A. 110 3-32 SYSTEM-SPEED DIALING-SYSTEM (6/9) Speed Dial Type No, (Toll Restriction Level) Set Data DialNumber(including 111 112 113 1 1 4 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 3-33 COaccess code) SYSTEM-SPEED DIALING-SYSTEM (7/9) Speed _ Dial Set Data We N o . ( T o l l Restrictton Level) Dial Number (including CO access code) 136 137 1 138 146 147 148 149 I 150 1 151 152 153 154 155 156 157 158 160 3-34 SYSTEM-SPEED DIALING-SYSTEM (8/9) -- __ Speed Dial We No. (Toll Restriction Level) Set Data Dial Number (including CO access code) 161 162 -_.. 163 I 164 165 166 167 168 s’:: .- 184 185 3-35 SYSTEM-SPEED DIALING-SYSTEM (9/9) Speed Dial Set Data Type N o . ( T o l l Restriction Level) Dial Number (including CO access code) 186 ; 187 j 188 / 189 190 191 192 193 194 195 196 197 198 199 200 3-36 SYSTEM-ABSENT MESSAGE j Default V a l u e Set Cz.ta item Fixed Message I I 4 Back At %%:%%%% I 6 Out Until %%I%% 6 At Ext %%%% -.-- 7 8 Flexible Message 11 I I 12 I 13 14 Remark: Fixed Message (1 to 6): Flexible Message (7 to 16): Fixed messages cannot be changed. %: enter these at extensions letters, numbers, and up to five % within 16 digits %: enter these at extensions 3-37 blank 4. Group GROUP-TRUNK GROUP (l/2) Trunk Grow No. 01 Item q DODD, Type ’ Name Default Set Data - - FEX, q WATS. 3 - q PvL. q digits (alphanumeric PBX, DlD DDD characters) Tenant 01. Incoming/Outgoing 0 Incoming only, cf Outgoing only, 0 Both-way I ATT, q Incoming Mode (Night) Intercept Routing (Day) OAT-T Intercept Routing (Night) q Toll Restriction Level - co 1 cl2 q q Incoming Mode (Day) q Value DKSA, 001~ 19, [~DIL i:~, q FLEXIBLE, q FIXED, q q EXT- ( 3 EXT- ( 3 o r Day Mode, q o r 4digits), TAFAS I, Both-way q TAFAS 21 DISA Toll Restriction Table None 0 N o n e None l 16 1 1 digit ( 1 t o 8) Dialing Plan OType-A, q CO-CO Duration Limit 1 Disconnect Time 0 1.5 seconds. 04.0 seconds 1.5 Pause Time 0 1.5 seconds, 02.5 seconds, 03.5 seconds, 04.5 seconds 3.5, - .- Hook Switch Flash Time 080 mseconds. 0300 mseconds, 0600 mseconds, [7900 mseconds, 01200mseconds, ONone Remark DDD: FEX: WATS: PVL: PBX: DID: Type-B, q l Flexible 4digits). [7 N o n e 2 digits (01 to 16) - DIL i:t o r minute(s) 2 digits Direct Distance Dialing Foreign Exchange Wide Area Telecommunication Service Private Line Behind PBX Direct Inward Dialing (1 Type-C, 0 None to All-: DIL 1 :l : DIL 1 :N: DISA TAFASl , 2: 64) None IO None Attendant Console Direct In Line (1 :l ) Direct In Lines (1 :N) Direct Inward System Access Trunk Answer From Any Station Day mode: Change Night receiving mode to Day receiving mode. Fixed: Incoming..call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can not change at Operator). Flexible: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can be changed at Operator). If ATLC is installed, default value for Incoming Mode (Day) is ATT. l 4-l GROUP-TRUNK GROUP (2/2) Trunk Group No. 01 Set Data Item destination (DIL 1: N only) Type and Number il” ” --+ Default Vsiue __. - -.--~-~ None g PCKUP - 0 0 Pickup group No. (01 to 32) TEXT - 1-1 rj n r]DN (3 or 4 digits) ---+ 0 IGM group No. (1 to 8) I-JCM - None cl” ” q PCKUP, q 0 Pickup group No. (01 to 32) q ]EXT - [-] rl n r/DN (3 or 4 digits) q lCk.4 - 0 ICM group No. (1 to 8) - None 0”” q PCKUP- 0 q Pickup group No. (01 to 32) [TEXT - n 11 rj fJDN (3 or 4 digits) q ICM - 0 ICM group No. (1 to 8) Cl” - / -___ / blank blank - None q PCKUP- 0 c] Pickup group No. (01 to 32) q JEXT - 0 [7 (7 q DN (3 or 4 digits) q ICM - 0 ICtvl group No. (1 to 8) - None 0”” q PCKUP- q 0 Pickup group No. (01 to 32) q ]EXT --+ 11 rj n fJDN (3 or 4 digits) q ICM -, 0 ICM group No. (1 to 8) cl” * bhnrc blank blank - None q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT - 0 f-l r-j r]DN (3 or 4 digits) q ICM - q ICM group No. (1 to 8) - None cl” q PCKUP - 0 q Pickup group No. (01 to 32) TEXT - 0 f-j n r]DN (3 or 4 digits) [7ICM ----+ 0 ICM group No. (1 to 8) - None q PCKUP- 0 0 Pickup group No. (01 to 32) q lEXr - 0 0 0 q DN (3 or 4 digits) q lCM - 0 ICM group No. (1 to 8) blank blank cl” ” DID Digit Modification Table PBX Access Code with Pause PBX Access Code with Restriction 0 1 digit (1 to 4) q uo UUCI q u q q l00 1 q uu q uu q ou Max-3dW q ICIU 000 q ClCl @wWOtW 00 q q u q q u q Max.3dWs lll-‘ln 00 q 17OO Figures WW Max. Dial No. after EFA Signal c l (0 to 7) CO Appearance Type 0 Single 0 Group blank blank blank 0 Single 4-2 GROUP-TRUNK GROUP (l/2) Trunk Group No. 02 ) Name j--- 1Tenant 101, Incoming/Outgoing Incoming Mode (Day) incoming Mode (Night) I Intercept Routing (Day) Intercept Routing (Night) 3 c!ig?s (alphanumeric characters) 17 Incoming only. 3 Ouigoing q ATT, q DisA. q DlL 19. q DtL i:N, q 1q FLEXIBLE, IJFIxED, [7Day Mode, IJDISA 1 q ATT q EXT - ( 3 o r 4digits). q EXT --+ ( 3 o r 4digits), 0 N o n e Dialing Plan q CO-CO Duration Limit 1 Disconnect 0 1 . 5 s e c o n d s , 04.0 seconds Remark DDD: FEX: WATS: PVL: PBX: DID: TAFASI, q DIL 17 TAFAs~ o r q 2 minute(s) d i g i t s ONone -1piiq None 16 1 Type-C, 0 None ( 1 t o None 6 4 ) 10 1.5 lo 1.5 seconds, 02.5 seconds, 03.5 secoctds, 04.5 seconds I 080 mseconds. 0300 mseconds. 0 600 mseconds, 0900 mseconds,n1200 mseconds, ONone Direct Distance Dialing Foreign Exchange Wide Area Telecommunication Service Private Line Behind PBX Direct Inward Dialing ATT: DIL 1 :l : DIL 1 :N: DISA TAFASl ,2: Attendant Console Direct In Line (1 :l ) Dired In Lines (1:N) Direct Inward System Access Trunk Answer From Any Station Day mode: Change Night receiving mode to Day receiving mode. Fixed: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can not change at Operator). Flexible: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can be changed at Operator). lf ATLC is installed, default value for Incoming Mode (Day) is ATT. l 4-3 l Flexible 1 digit (1 to 8) Type-A. 0 Type-B. I I 2 digits (01 to 16) - Hook Switch Flash Time 1 Both-way only, 17 Both-way Toil Restriction Table I Pause Time co -I I 12 Toll Restriction Level Time I 3.5 None I GROUP-TRUNK GROUP (212) Trunk Group No. 02 Sei Data item Destination (DIL 1: N only) Type and Number J” - Default - V a -l u e -+ None - - XPCKUP + ?EXT -JICM -! Pickup G-OIJP No. (01 to 32) --, r! i-j n [?,DN (3 or 4 digits) blank --, 5 ICM group No. (1 to 8) 3” - -None UPCKUP - C a Pickup group No. (01 to 32) q EXT -JCM --, q c] q q blank DN (3 or 4 digits) -+ 0 ICM group No. (1 to 8) ‘c C7” ” - None [IPCKUP - c] 0 Pickup group No. (01 to 32) C JEXT --s 0 n n nDN (3 or 4 digits) C -JICM - q JCM group No. (1 to 8) [II” - --+ None [ IPCKUP - 17 [7 Pickup group No. (01 to 32) 1 JEXT +~~O~DN(3or4digits) []lCM - 0 ICM group No. (1 to 8) [3” ” --+ None [Z]PCKUP--, q q Pickup group No. (01 to 32) E Z]EXT __ 0 0 0 q DN (3 or 4 digits) [ -JlCM --, /J ICM group No. (1 to 8) [3” - None [Z]PCKUP-+ 0 q Pickup group No. (01 to 32) 1Z]EXT --+ 0 0 0 q DN (3 or 4 digits) IZ]ICM - 0 ICM group No. (1 to 8) I7” ” - None blank blank :’ P blank blank Z]PCKUP ----, @ 0 Pickup group No. (01 to 32) - 0 q q q DN (3 or 4 digits) Z]EXT CjlCM -+ 0 ICM group No. (1 to 8) blank - None D”” q PCKUP- q 0 Pickup group No. (01 to 32) UEXT -~~OuDN(3or4digits) - 0 ICM group No. (1 to 8) I-JCM PBX Access Code with Restrictio In q 1 digit (1 to 4) q nu q uu cm0 q uu Max.3digfis q UU q U U q UU q U 0 Figures @to 9) q uu q clu uuu q uu Max.3dighs q UU q OU UIJU 000 FiguresPto9) Single 1 blank .: blank 0 IJ (0 to 7) q blank q Single Group 4-4 GROUP-TRUNK GROUP (l/2) Trunk Grout, No. 03 Item q 1DODD, FEX. •WAT~. I --- Name lot. 1Incoming/Outgoing q PvL, q lmx. CDID 02 117 .inCOming only, 0 Outgoing only, q 1 Toll Restriction Level I - - Intercept Routing (Day) / WATT, ~DISA, I I Dialing Plan I Disconnect Time 1 o r 1q I 0 Type-B, q minute(s) 2 d i g i t s t o 6 4 ) I Pause Time ml.5 seconds, 02.5 seconds, 03.5 seconds;‘Cj4.5 seconds Hook Switch Flash Time 080 mseconds, 0900 mseconds, FEX: WATS: PVL: PBX: DID: Direct Distance Dialing Foreign Exchange Wide Area Telecommunication Service Private Line Behind PBX Direct Inward Dialing 1 I ’ I m s e c o n0d s , 600 mseconds, 0300 1200 mseconds. ONone A-l-T: DIL 1:l: DIL 1 :N: DISA TAFASl, 2: Attendant Console Direct In Line (1 :I ) Direct In Lines (1 :N) Direct Inward System Access Trunk Answer From Any Station Day mode: Change Night receiving mode to Day receiving mode. Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Fixed: Universal Night Answer (Can not change at Operator). Flexible: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can be changed at Operator). ff ATLC is installed, default value for lncomino Mode (Dav) is ATT. l 4-s None 16 Remark DDD: None I- I s seconds, 04.0 seconds q I DIL 1~1 * 7 Type-C, 0 None ( 1 I 1 Flexible 1 digit (1 to 8) I aType-A, CO-CO Duration Limit -~AFAs 2 2 digits (01 to 16) I Toil Restriction Table o Beth-way Both-way 1 Intercept Routing (Night) Incoming Mode (Night) c ! I q DIL i:i, 001~ I:N. q TAFAS I. q 1q FLEXIBLE, q FIXED, q Day Mode, ~DISA 1 q Arr TEXT - ( 3 o r 4digits), 0 N o n e I q EXT e (3 o r 4digits), 0 N o n e Incoming Mode (Day) DDD 3 digits (alphanumeric characters) I Tenant Default Valu - -.--- e- - Set Data 1 I I -. I None I 10 I 1.5 I 3.5 None GROUP-TRUNK GROUP (212) T-;nk Group No. 03 _-- -.~ - kern - .-~_ 3?SYination ;DIL 1. N only) !I@ ar"j PJ,Jmtsr Default Value -~ Set Data - None 3’ ” flPCKUP--+ q 0 Pickup group No. (01 to 32) q EXT q ICM - n n n nDN (3 or 4 digits) - 0 ICM group No. (1 to 8) cl” -None q n blank PCKUP, 0 0 Pickup group No. (01 to 32) [7EXT -, /J 0 q q DN (3 or 4 digits) q ICtVl ---, 0 ICM group No. (I to 8) cl” - blank - None q PCKUP 3 q q Pickup group No. (01 to 32) q EXT --+ q 0 c] q DN (3 or 4 digits) q ICM - [7 ICM group No. (1 to 8) blank - None cl” q PCKUP - q 0 Pickup group No. (01 to 32) q EXT ~DN (3 or 4 digits) q ICM -q ICM group No. (1 to 8) blank - None 0” ” q PCKUP --, 0 q Pickup group No. (01 to 32) q EXT - n n n ODN (3 or 4 digits) q lCM -, c] ICM group No. (1 to 8) blank - None 0”” q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT -OOnnDN(3or4digits) - 0 ICM group No. (1 to 8) OICM blank - None q PCKUP- 0 0 Pickup group No. (01 to 32) -+OOOODN(3or4digits) TEXT q lCM --, c] ICM group No. (1 to 8) blank - j-l n ri cr” - None PCKUP- 0 0 Pickup group No. (01 to 32) EXT -nnnr]DN(3or4digits) ICM - 0 ICM group No. (1 to 8) 0”” DID Diait Modifcation Table q q q q TBX AUXSS Code with PaUse 000 blank 1 digit (1 to 4) clclcl 1 000 clclcl Max-3dig~s blank iMax. Dial No. after EFA Simml Cl00 lJCliIl q IIJCI 000 RwrWOto9) clcKl clucl 000 0017 Max.3dke IJCIO q ICICI Cl00 q ICICI FiguresWog) q (0 to 7) ICO Appearance Type c] Single 0 Group Single PBX Access Code with Restrictiir 4-6 blank 0 GROUP-TRUNK GROUP (l/2) Trunk Grow No. 04 Item We q Name -~- Tenant 01, incoming/Outgoing 0 Incoming only, [? Outgoing only, [7 Both-way DDD, IJFEx, [?WATS. IJPvL, q Pex, q - Toll Restriction Table - Dialing Plan q CO-CO Duration Limit 1 Disconnect Time 01.5 s e c o n d s , 04.0 seconds Pause Time 01.5 Hook Switch Flash Time 080 mseconds, 0300 mseconds, 0 600 mseconds, 0900 mseconds, 01200 mseconds. aNone Remark DDD: FEX: WATS: PVL: PBX: DID: co 1 Toll Restriction Level Intercept Routing (Day) DDD 02 Intercept Routing (Night) Incoming Mode (Night) DID 3 digits (alphanumeric characters) q q q q Incoming Mode (Day) Default Value Set Data ATT, ODISA, FLEXIBLE, ATT q q q ]FIXED, EXT - ( 3 EXT -+ ( 3 o r DIL I:I, C)DIL 1:~. /JTAFAS I, q Day Mode, or 4digits). 4digits). q DISA q Both-way q TAFAS 2 DIL Flexible None None 0 N o n e None 2 digits (01 to 16) - 16 1 digit (1 to 8) 1 Type-A, 0 Type-B, 0 Type-C, 0 None o r 2 minute(s) d i g i t s seconds, 02.5 Direct Distance Dialing Foreign Exchange Wide Area Telecommunication Service Private Line Behind PBX Direct Inward Dialing ( 1 t o seconds, None 6 4 ) 10 1.5 173.5 seconds, Al-T: DIL 1:l: DIL 1 :N: DISA TAFASl , 2: 04.5 seconds .” Attendant Console Direct In Line (1 :l ) Direct In Lines (1 :N) Direct Inward System Access Trunk Answer From Any Station Day mode: Change Night receiving mode to Day receiving mode. Fixed: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can not change at Operator). Flexible: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can be changed at Operator). ff ATLC is installed, default value for Incoming Mode (Day) is ATT. l 4-7 t:i 3.5 None l GROUP-TRUNK GROUP (212) Trunk ~- Grotip No. 04 Default Value Set Data item c -,., / I -J Destina’tion (DIL 1: N only) Type and Number -None n q IPCKUPg PI&UP group No. (01 to 32) ;EXT --,. n n v nDN (3 or 4 digits) -ICM - 0 ICM group No. (1 to 8) J -,,, n - None -JYPCKUP -, 0 0 Pickup group No. (01 to 32) --, 0 0 g mDN (3 or 4 digits) TEXT =ICM --, 0 ICM group No. (1 to 8) --,, n -None LJ 3PCKUP - c] @ Pickup group No. (01 to 32) blank blank L - 0 0 f’-j TEXT ZICM q -S c] ICM group No. (1 to 8) --j None Cl” ” gPCKUP+ Pickup group No. (01 to 32) --+ rl ri n r[DN (3 or 4 digits) CJEXT q q q ICM cl” ” q ----j None q q ICM - 0 ICM group No. (1 to 8) cl” - None ” PCKUP- 0 0 Pickup group No. (01 to 32) - 000 DN (3 or 4 digits) TEXT q q ICM Cl” q q blank - None ” PCKUP- 0 0 Pickup group No. (01 to 32) - 000 q blank DN (3 or 4 digits) - 0 ICM group No. (1 to 8) 1 0 1 digit (1 to 4) 000 000 00 0 000 clocl 00 q 000 000 00 0 000 Figures(Oto9) cl00 Max.3digits 00 0 Figures (Oto 9) blank blank 0 c l (0 to 7) Single c] Single 0 Group a blank - 0 ICM group No. (1 to 8) EXT [7lCM PBX Access Code with Restrictior blank - None n PCKUP - c) 0 Pickup group No. (01 to 32) - nn n DN (3 or 4 digits) TEXT q blank ---+ 0 ICM group No. (1 to 8) q PCKUP --, c] 0 Pickup group No. (01 to 32) q EXT - n fl n q DN (3 or 4 digits) q lCM --, 0 ICM group No. (1 to 8) El” blank DN (3 or 4 digits) 4-8 GROUP-TRUNK GROUP (l/2) Trunk Group No. 05 Item Set Data Type q Name - DDD, q FEX, - q WATS, IJPvL, [?PBx, q DID I 3 digits (alphanumeric characters) - 1B o t h - w a y Incoming/Outgoing t 0 Incoming Mode (Day) 1oAT-L 0 DIsA, q m 19, q DlLi:N, q TAFASI, q TAF~s2j Incoming Mode (Night) 1 intercept Routing (Day) 10~17q Intercept Routing (Night) lo EXT ---j-.m---.- (3 or 4digits). 0 None Toll Restriction Level I -- Toll. q FLEXIBLE, only, 0 Outgoing only, 0 Both-way q q FIXED, EXT---+ ( 3 Day Mode, o r q 4digits), DIL i:i DISA 0 N o n e 2 digits (01 to 16) Restriction Table CO-CO Duration Limit ’ Disconnect Time Time 1 o r minute(s) 2 d i g i t s ( 1 lo 1.5 seconds, 04.0 seconds ICI 1.5 02.5 seconds, Hook Switch Fl&h iime seconds, to 6 4 ) 03.5 seconds, I 04.5 seconds Flexible I None I I I None I 16 I 1 I None I I I I 080 mseconds, 0300 mseconds, 0600 mseconds, 0900 mseconds.01200 mseconds, ONone Remark DDD: FEX: WA-l-S: PVL: PBX: DID: Direct Distance Dialing Foreign Exchange Wide Area Telecommunication Service Private Line Behind PBX Direct Inward Dialing AIT: DIL 1:l: DIL 1:N: DISA TAFASl , 2: Attendant Console Direct In Line (1:l) Direct In Lines (1 :N) Direct Inward System Access Trunk Answer From Any Station Day mode: Change,.Night receiving mode to Day receiving mode. Fixed: incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can not change at Operator). Flexible: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can be changed at Operator). If ATLC is installed, default value for Incoming Mode (Day) is AlT. l 4-9 l I I 1 digit (1 to 8) lo Type-A, 0 Type-B, 0 Type-C, 0 None Dialing Plan Pause Incoming co 1 10 1.5 3.5 None I I I GROUP-TRUNK GROUP (212) Trunk Group No. 05 -., Destination (DIL 1: N only) Type and Number Default Value Set Data Item n - Nc-e ZPCKUP --+ c 1 Pickup group No. (0; to 32) -‘EXT - r 1 n ;IDN (3 O: 4 digi?s) ---CM --+ C ICM group No. (1 to 8) -u n - Nc-e i JPCKUP, 1-J Pickup group No. (01 to 32) TEXT - r 1 n :-]DN (3 or 4 digl:s) +A - 1 ICM group No. (1 to 8) -l&S n - Nc-e biank blank jPCKUP -c 1 Pickup group No. (Oi to 32) C]EXT - r .-I n ~DN (3 or 4 digfs) - c ICM group No. (1 to 8) 7JCtVl 3” ” blank --NC-e JPCKUP- c 1 Pickup group No. (01 to 32) TEXT -c 1 q q DN (3 or 4 digits) q ICtVl - 1 ICM group No. (1 to 8) blank - Ncte q PCKUP- c J Pickup group No. (01 to 32) f-JEXT --+ r 7 n r]DN (3 or 4 digfts) q ICM -C ICM group No. (1 to 8) cl” * blank -None cl” ” [IIPCKUP- 1 a Pickup group No. (01 to 32) q EXT - r n n nDN (3 or 4 digits) q ICM - c ICM group No. (1 to 8) , blank - None cl” n q PCKUP- c 0 Pickup group No. (01 to 32) q EXT - I- n f-j ~DN (3 or 4 digAs) q IChfl - c ICM group No. (1 to 8) blank ----+ None cl” * q PCKUP --+ c 0 Pickup group No. (01 to 32) - c 0 0 q DN (3or 4 digits) (TEXT ---+ c ICM group No. (1 to 8) OICM DID Digit Modification Table [7 1 digit (1 to 4) PBX Access Code with Pause 000 000 blank 1 Cl00 000 M=x-3dWs Pf3X Access Code with Restrictior Cl00 CID0 q lClCl Cl00 Fkwes(Oto9) q ICICJ Elclo cl00 clclcl M=x*3dWs q ICICI q JCICJ q ICICI q ICICIQwsWo9) Max. Dial No. after EFA Signal cl (0 to 7) CO Appearance Type q blank blank 0 Single Single 0 Group 4-l 0 GROU P - T R U NK GROUP (l/2) Trunk Grow No. 06 Item 0000, We Name Default Value- - Set Data /- q - FEX, SWATS. UPVL. - q PBx, EDID 3 digits (alphanumeric characters) 101, Incoming/Outgoing / 0 incoming only, 0 Outgoing only, 0 Both-way Incoming Mode (Night) Intercept Routing (Day) Intercept Routing (Night) I co I Tenant Incoming Mode (Day) DDD 1 02 1 q AT, q DISA, ODIL l:l, q DlL l:N. q ID FLEXIBLE, q FIXED, q Day Mode, q DiSA 1 IJAm q EXT---, ( 3 o r 4digits). q q EXT --+ ( 3 o r 4digits), 0 N o n e Both-way TAFAS 1, q TAFAS 21 -~ DIL I:1 Flexible None None None Toll Restriction Level - Toll Restriction Table __ Dialing Plan q CO-CO Duration Limit 1 Disconnect 0 1.5 s e c o n d s , 04.0 seconds 1.5 Pause Time 0 1 . 5 seconds, 02.5 seconds, 03.5 seconds, 04.5 seconds 3.5 Hook Switch Flash Time 080 m s e c o n d s , 0300 m s e c o n d s , 0600 m s e c o n d s . 0900 mseconds,C]1200 mseconds, ONone Time - 2 digits (01 to 16) 16 1 digit (1 to 8) 1 Type-A, [7 Type-B, o r q 2 minute(s) d i g i t s Type-C, 0 None ( 1 t o 6 4 ) Remark DDD: FEX: WATS: PVL: PBX: DID: Direct Distance Dialing Foreign Exchange Wide Area Telecommunication Service Private Line Behind PBX Direct Inward Dialing ATT: DIL 1:l: DK 1:N: DISA TAFASl , 2: Attendant Console Direct In Line (1 :l ) Direct In Lines (1:N) Direct Inward System Access Trunk Answer From Any Station Day mode: Change Night receiving mode to Day receiving mode. Fixed: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can not change at Operator). Flexible: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can be changed at Operator). l if ATLC is installed, default value for Incoming Mode (Day) is ATT. 4-11 None 10 None * GROUP-lRUNKGROUP(2/2) Trunk Grow No. 06 destination (DIL 1: N only) Type and Number Default Value Set Data Item 7” ” --+ None q TEXT 1 Pickup group No. (01 TO 32) --+ 0 1 J CDN (3 or 4 digits) -JlCM - 13 ICM group No. (1 to 8) IPCKUP - blank -, None II” ” IPCKUP- c] C Pickup group No. (01 to 32) ;EXT - 0 r 1 nDN (3 or 4 digits) ;lCM - q blank ICM group No. (1 to 8) -None 3’ IPCKUP - 0 c Pickup group NO. (01 io 32) IEXT JlCM c :J DDN (3 or 4 digits) - 0 ICM group No. (1 to 8) 3,’ -None ” blank - q Fz$‘;lJP - 0 [z Pickup group No. (01 to 32) - 0 c D q blank DN (3 or 4 digits) iICM ----+ 0 ICM group No. (1 to 8) 0” ” - None q lCM q C Pickup group No. (01 to 32) - q 10 q DN (3 or 4 digits) q ICM grqup No. (1 to 8) cl” - None EPCKUP CEXT - q ” blank PCKUP - q c Pickup group No. (01 to 32) [?ExT - n I? n nDN (3 or 4 digits) q ICM - 0 ICM group No. (1 to 8) blank -None III” ” q ]PCKUP--+ 0 E Pickup group No. (01 to 32) q EXT - 0 0 0 q DN (3or 4 digits) q lCM - [7 ICM group No. (1 to 8) blank --+ None Cl” q PCKUP- 0 q [TEXT I-JICM >I0 Digit Modification Table 3X Access Code with Pause 3X Access Code with Restrictior Pickup group No. (01 to 32) DN (3 or 4 digits) - 0 ICM group No. (1 to 8) blank - 0 q 0 q q 1 digit (1 to 4) nrln q IIJD cl00 cKlcl 000 q IIJCI 000 q OO cl00 cllJcl clcKl 1700 000 000 000 000 MT. Dial No. after EFA Simal 0 (0 to 7) ZO Appearance Type 0 Single 0 Group 1 Max.3digfis Wres(Oto9) Max-3dig~s FiwresPto9) blank blank 0 Single 4-12 GROUP-TRUNK GROUP (l/2) Trunk Group No. 07 Item ~DDD. /-JFEX, Name - - /31. Tenant ( Incoming/Outgoing Incoming Mode (Day) 1incoming Mode (Night) Intercept Routing (Day) Restriction Level q Pause Time Hook Switch Flash Time Remark DDD: FEX: WATS: PVL: PBX: DID: DDD I q ( 12 Incoming only, 0 Outgoing only, 1IIAIT, q 1~FLE~IBLE, ) g~7-r q DISA. 001~ 111, /JF~XED, q -( 3 q EXT- ( 3 o r I-- DILYN, [~TAFAS 1, •TAFAS~I ]Day Mode, 0 o r 4digits). 4digits). Flexible DISA I I 0 N o n e 0 N o n e 2 digits (01 to 16) I I I ICI 1.5 seconds, 04.0 seconds IO 1.5 I minute(s) 2 d i g i t s ( 1 t o 6 4 ) seconds, 02.5 seconds, 03.5 seconds. 04.5 seconds 080 mseconds, 0300 mseconds. c]600 mseconds, c]900 mseconds, 01200 mseconds, ONone Direct Distance Dialing Foreign Exchange Wide Area Telecommunication Service Private Line Behind PBX Direct Inward Dialing Al-T: DIL 1:1: DIL 1 :N: DISA TAFASl , 2: 1 DIL t:t I I o r 4-13 I 1 l I None I None I 16 I 1 I None I 10 1.5 3.5 None Attendant Console Direct In Line (1 :l) Direct In Lines (1:N) Direct Inward System Access Trunk Answer From Any Station Day mode: Change Night receiving mode to Day receiving mode. Fixed: Incoming-call only arrives on either DN which set by Night Answer Point of Trunk or External pager of Universal Night Answer (Can not change at Operator). Flexible: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External Pager of Universal Night Answer (Can be changed at Operator). lf ATLC is installed. default value for Incoming Mode (Day) is ATT. l I Both-way ( Both-way 1 digit (1 to 8) 1 co l 1aType-A, 0 Type-B, 0 Type-C, [7 None I CO-CO Duration Limit I-~Disconnect Time I Value PvL, DPex, ODID 3 digits (alphanumeric characters) - I Toll Restriction Table Dialing Plan q WAE, 02 iEXT I Intercept Routing (Night) IX (Toll Default Set Data I I I GROUP-TRUNK GROUP (2/2) unk Group No. 08 cl” ” estination (D’L ’ ’ N ‘“I’) Type and Number Default Value Set Data Item -+ None q PCKUP ---, 0 q Pickup group No. (07 to 32) q EXT - n n n EDN (3 or 4 digns) q lCM - [7 ICM group No. (1 to 8) blank -None 0” ” q PCKUP-, 0 q Pickup group No. (01 to 32) q ]EXT - 0 q 0 q DN (3 or 4 digits) q ICM -q ICM group No. (1 to 8) blank -None 0”” q PCKUP-• q Pickup group No. (01 to 32) q EXT -+ n n r-1 ~DN (3 or 4 digits) q ICM -----+ q ICM group No. (1 to 8) blank -None cl” ” q PCKUP - q 0 Pickup group No. (01 to 32) q EXT --+ n rj ri r]DN (3 or 4 digits) q ICM ----+ 0 ICM group No. (1 to 8) blank -None cl” w q PCKUP ----,/J q Pickup group No. (01 to 32) q EXT --, •IJ 0 0 q DN (3 or 4 digits) q lCM ----+/-J ICM group No. (1 to 8) blank 0”” q - None PCKUP- 0 0 Pickup group No. (01 to 32) TEXT -+ 0 n n rjDN (3 or 4 digits) q JICM w c) ICM group No. (1 to 8) cm blank ---c None q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT --+ ri n r-1 ~DN (3 or 4 digits) q ICM ---, q ICM group No. (1 to 8) - None 0’” q PCKUP - 0 0 Pickup group No. (01 to 32) q EXT -OnnnDN(3or4digits) - 0 ICM group No. (1 to 8) clK=M IID Digit Modification Table 0 1 digit (1 to 4) ‘8XAccess Code with Pause 000 000 ml0 q JCICI Max.3dWs q UO IJIJCI IJCICI q lClCl NwWOto9) ~BXAccessCodewith Restriction 00 0 .a 00 0 0 Pto7) ZO Appearance Type 0 Single 0 Group blank 1 00 0 c]o 0 Max+3digits q ICICI 000 000 q OU RwWOtW tix. Dial No. after EFA Signal blank blank blank 0 Single 4-14 GROUP-TRUNK GROUP (l/2) Trunk Grow No. 08 Item We q DDD, Name - - Tenant clfp [ Incoming/Outgoing FEX, q WATS. q PvL, q incoming Ody,0 CO-CO Duration Limit 1 Disconnect Time ml.5 Pause Time DIL 1:1 I o n e 0 N o n e minute(s) 2 d i g i t s seconds, 04.0 ( 1 t o None I I 16 None 6 4 ) FEX: WATS: PVL: PBX: DID: 1.5 q 080 mseconds, 0300 mseconds. 600 mseconds. 0900 mseconds,01200 mseconds, ONone ATT: DIL 1:l: QIL 1 :N: DISA TAFASl , 2: I 3.5 None Attendant Console Direct In Line (1 :l) Direct In Lines (1:N) Direct Inward System Access Trunk Answer From Any Station Day mode: Change Night receiving mode to Day receiving mode. Fixed: Incoming-call onfy arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can not change at Operator). Flexible: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can be changed at Operator). H ATLC is installed, default value for fncomina Mode (Day) is ATT. l 4-15 I 10 seconds 02.5 seconds, 03.5 seconds, 04.5 seconds Direct Distance Dialing Foreign Exchange Wide Area Telecommunication Service Private Line Behind PBX Direct Inward Dialing I 1 Remark DDD: I ---1TGJ Type-A, 0 Type-B. 0 Type-C 0 None o r I l Flexible 1 digit (1 to 8) / 0 1.5 seconds, Hook Switch Flash Time 4digits), TAFAS I. •TWG~~ 2 digits (01 to 16) Iq Both-way Outgoing only, 0 Both-way o r -- Dialing Plan co 1 Ia EXT --, ( 3 Toll Restriction Table DDD cl2 Intercept Routing (Night) Toll Restriction Level lPBx, ODlD 3 digits (alphanumeric characters) - intercept Routing (Day) 1 Incoming Mode (Night) I 10 q 1q ATT, [~DISA, q DIL 111. q DILI:N, q 1 q I=LEX~BE, q FiXED, q Day Mode, q D1.W 1 q ATT q EXT - ( 3 o r 4digits). 0 N Incoming Mode (Day) Default Value Set Data I GROUP-TRUNK GROUP (212) Trunk Group No. 08 Default Value Set Data item n estination (DIL 1: N only) Type and Number --+ None $CK”P - 0 c] Pickup group No. (01 to 32) ?ExT -0 0 q q DN (3 or 4 digits) -JICM - 0 ICM group No. (1 to 8) b!ank - None IPCKUP, 0 j-J Pickup group No. (01 to 32) IEXT - 0 0 0 jJDN (3 or 4 digits) -JCL4 - 0 ICM group No. (1 to 8) blank 7” * 7” ” -None IPCKUP- 0 0 Pickup group No. (01 to 32) JExT --+ En l-j nDN (3 or 4 digits) JICM -q ICM group No. (1 to 8) blank - None 7” ” IPCKUP- 0 0 Pickup group No. (01 to 32) -0 0 c] q DN (3 or 4 digits) JExT JICM -q ICM group No. (1 to 8) blank - None 7” ” JPCKUP- 17 0 Pickup group No. (01 to 32) UEXT ----+ q 0 0 q DN (3 or 4 digits) q ICM -q ICM group No. (1 to 8) Cl” ” q q blank - None PCKUP- 0 0 Pickup group No. (01 to 32) -0 0 0 q DN (3 or 4 digits) EXT 3lCM - 0 ICM group No. (1 to 8) blank - None Cl” ” q PCKUP- q 0 Pickup group No. (01 to 32) TEXT ----, j-J 0 q q DN (3 or 4 digits) q iCM -S 0 ICM group No. (1 to 8) blank --w None 0”” q blank PCKUP- 0 0 Pickup group No. (01 to 32) DExT - 0 0 q q DN (3 or 4 digits) q lCM - q ICM group No. (1 to 8) q 1 digit (1 to 4) q IOIJ q uu q uu q uo 000 q lUU 000 q UU q ou q oo cl00 q ou IJIJCI q UO 000 000 blank blank Single Single 0 Group 4-l 6 Q M=x-3dWs FiguresWo9) M=x-3digfis WresWo9) 0 cl (0 to 7) q 1 GROUP-TRUNK GROUP (l/2) Trunk Group No. 09 Item Set Data q DDD, q ]FEX, IJWATS, q lPvt., q lmx, q 3 digits (alphanumeric characters) Name - IncomihgIOutgoing 0 Incoming only, 0 Outgoing only, 0 Both-way - - Intercept Routing (Day) q TAFAS I, q 1 q FLEXIBLE, OFiXED. q Day Mode, q DlSA 1 OAT-T q EXT- ( 3 o r 4digits), 0 N o n e Intercept Routing (Night) IO EXT - Toll Restriction Level I - Incoming Mode (Day) Incoming Mode (Night) (OAT-T, q DISA, q - - - I Toll Restriction Table Dialing Plan DID ]DIL I:I, 001~ I:N, - (3 or 4digits), - Both-way TAFAs~I 0 None I 1 o r I I I None I I l 16 1 digit (1 to 8) I 1 ( 1 t o 6 4 ) I 10 01.5 seconds, 04.0 seconds 1.5 Pause Time 01.5 seconds, 02.5 seconds. 03.5 seconds, 04.5 seconds 3.5 Hook Switch Flash Time 080 m s e c o n d s , 0300 m s e c o n d s , 0 600 mseconds, 0900 mseconds,nl200 mseconds, ONone None Remark Dired Distance Dialing Foreign Exchange Wide Area Telecommunication Service Private Line Behind PBX Direct Inward Dialing Al-l-: DIL 1:1: DIL 1:N: DISA TAFASI ,2: Attendant Console Direct In Line (1 :I ) Dired In Lines (1 :N) Direct Inward System Access Trunk Answer From Any Station Day mode: Change Night receiving mode to Day receiving mode. Fixed: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can not change at Operator). Flexible: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can be changed at Operator). ff ATLC is installed, default value for Incoming Mode (Day) is ATT. l 4-17 -1 None Disconnect Time DDD: FEX: WATS: PVL: PBX: DID: 1 None 2 digits (01 to 16) 2 minute(s) d i g i t s l Flexible aType-A, c] Type-B, 0 Type-C, 0 None CO-CO Duration Limit DIL 111 I GROUP-TRUNK GROUP (2/2) Trunk Group No. 09 - None cl” ” ~f~~~~~,$~~~~rN Default Value Set Data Item Only) q PCKUP- [7 0 Pickup group No. (01 to 32) q EXT - 0 0 0 q DN (3 or 4 digits) q ICM -..+ 0 ICM group No. (1 to 8) blank ‘0”. ” - None q PCKUP- 0 [7 Pickup group No. (01 to 32) f-JEXT - fJ 0 c] q DN (3 or 4 digits) q ICM -, 0 ICM group No. (1 to 8) blank - None ]PCKUP- c] 0 Pickup group No. (01 to 32) EXT --+ n ri rj rjDN (3 or 4 digits) ICM - 0 ICM group No. (1 to 8) blank ” --None q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT ----j 0 q 0 q DN (3 or 4 digits) q ICM - 0 ICM group No. (1 to 8) blank - None 0” ” q PCKUP- q 0 Pickup group No. (01 to 32) q EXT - 11 rl ri r]DN (3 or 4 digits) - 0 ICM group No. (1 to 8) /-JICM blank Cl” - q q q 0” ._ - None q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT - n n n q DN (3 or 4 digits) q ICM - 0 ICM group No. (1 to 8) cl” - .. - None q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT -~nnnDN(3or4digits) - 0 ICM group No. (1 to 8) /-JICM blank cl” = blank - None Cl-” q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT -nuu[7DN(3or4digits) l-J3A - 0 ICM group No. (1 to 8) blank )IDDigit Modifmtion Table 0 1 digit (1 to 4) 3X Access Code with Pause q IKJCI 000 000 Cm0 Max*3dWs 000 dax. Dial No. after EFA Signal cl (0 to 7) :O Appearance Type q 000 1 000 uoo Fkwes(OtoQ) blank blank 0 Single Single 0 Group 4-18 GROUP-TRUNK GROUP (l/2) Trunk GrouD No. 10 Item Default Value Set Data Type q DDD, Name - - Tenant lJl> cl2 Incoming/Outgoing 0 Incoming only, 0 Outgoing only, 0 Both-way Incoming Mode (Day) Incoming Mode (Night) Intercept Routing (Day) Intercept Routing (Night) OAT-T, q q q q FEX, q PvL, q PBx, 0~10 DDD co 1 DISA, q FLEXIBLE, q AT7 q JWATS. 3 digits (alphanumeric characters) - q q FIXED, q EXT -(3 ]EXT- ( 3 q DIL i:i, o r or DIL I:N, Day Mode, q 4digits). q TAFAS 1, q Both-way TAFAS 2 DISA q 2 digits (01 to 16) Tal! Restcictian Table 1 digit (1 to 8) i:t Flexible None 4digits), 0 N o n e Toll Restriction Level DIL None None 16 1 Dialing Plan q CO-CO Duration Limit 1 Disconnect Time 0 1.5 seconds, 04.0 seconds 1.5 Pause Time 0 1.5 seconds, 02.5 seconds, 03.5 seconds, 04.5 seconds 3.5 Hook Switch Flash Time 080 mseconds. 0300 mseconds, 0 600 mseconds, 0900 mseconds, q 1200 mseconds, ONone Remark DDD: FEX: WATS: PVL: PBX: DID: Type-A, 0 Type-B, [7 Type-C, 0 None o r minute(s) 2 digits Direct Distance DialingForeign Exchange Wade Area Telecommunication Service Private Line Behind PBX Direct Inward Dialing (1 to Al-f: DIL 1 :l : DIL 1 :N: DISA TAFASl (2: 64) None 10 None Attendant Console Direct In Line (1 :l) Direct In Lines (1 :N) Direct Inward System Access Trunk Answer From Any Station Day mode: Change Night receiving mode to Day receiving mode. Fixed: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can not change at Operator). Flexible: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can be changed at Operator). ff ATLC is installed, default value for Incoming Mode (Day) is ATT. l 4-l 9 l GROUP-TRUNK GROUP (212) Trunk Group No. 10 estination (DIL 1: N only) Type and Number Default _ _Value -.~ Set Data Item II” ” -+ None IPCKUP- 0 0 Pickup group No. (01 to 32) JEXT -+ n r[ n r]DN (3 or 4 digits) - 0 ICM group No. (1 to 8) JICM -+ None 7” ” ]PCKUP, 0 0 Pickup group No. (01 to 32) JEXT -0 0 0 q DN (3 or 4 digits) -----, fl ICM croup No. (1 to 8) 1ICM - blank blank None IPCKUP- 0 0 Pickup group No. (01 to 32) ]EXT Y 0 q 0 q DN (3 or 4 digits) -+ c] ICM group No. (1 to 8) 7JlCtvl c None PCKUP- 0 0 Pickup group No. (01 to 32) EXT -0 0 0 q DN (3 or 4 digits) ICM - 0 ICM group No. (1 to 8) blank cl” - q q q cl” * q q - None PCKUP- fJ 0 Pickup group No. (01 to 32) EXT -+ ri ri rj r/DN (3 or 4 digits) f--JlCM - 0 ICM group No. (1 to 8) cl” ” q q q q blank - None PCKUP- 0 0 Pickup group No. (01 to 32) TEXT - 11 n n r]DN (3 or 4 digits) q ICM - 0 ICM group No. (1 to 8) 0” * blank blank --+ None PCKUP- 0 0 Pickup group No. (01 to 32) EXT - n r-1 ri nDN (3 or 4 digits) - 0 ICM group No. (1 to 8) ICM --+ None PCKUP-w 0 0 Pickup group No. (01 to 32) EXT -, n n n nDN (3 or 4 digits) l-J34 - 0 ICM group No. (1 to 8) blank Cl” ” q q ‘BX Access Code with Pause q 1 digit (1 to 4) 000 clclcl cl00 q JCICI M=x.3dWs ‘BX Access Code with Restrictior 000 000 )iD Digit Modification Table Cl00 000 q ICICI q ICICI ‘. Diaiko. after EFA Signal cl (0 to 7) Appearance Type 0 Single 0 Group 000 000 UC10 FigurWOto9) 000 M=x.3Ws q ICICI q ICICIFWWOtW blank 1 blank blank 0 Single 4-20 GROUP-TRUNK GROUP (l/2) Trunk Group No. 11 Item Default Value Set Data Type q DDD, CFEX, Name - - Tenant cl1g Incoming/Outgoing 0 Incoming only, 0 Outgoing only, 0 Both-way Incoming Mode (Day) OATI, ~DISA, /JDIL I:I, COIL I:N, O-~AFAS 1, Incoming Mode (Night) Intercept Routing (Day) Intercept Routing (Night) q q q q q WATS, CPVL. PBX, [?DID DDD 3 digits (alphanumeric characters) - co 1 cl2 FLEXIBLE, q FIXED, AlT @EXT - ( 3 EXT - (3 or Toll Restriction Level q Both-way q TAFAS 2 Day Mode, ODEA o r 4digits). 4digits), q 1:~ DIL Flexible 0 N o n e None None None 2 digits (01 to 16) 16 1 digit (1 to 8) 1 Toll Restriction Table __ Dialing Plan q CO-CO Duration Limit 1 Disconnect Time 0 1.5 seconds, 04.0 seconds 1.5 Pause Time 01.5 seconds, 02.5 seconds, 03.5 seconds, 04.5 seconds 3.5 Hook Switch Flash Time 080 mseconds, 0300 mseconds, 0900 mseconds. 01200 mseconds, Type-A, 0 Type-B, 0 Type-C, c] None o r 2 minute(s) d i g i t s ( 1 t o 6 4 ) q 600 mseconds, ONone None 10 None Remark DDD: FEX: WATS: PVL: PBX: DID: Direct Distance Dialing Foreign Exchange Wide Area Telecommunication Service Private Line Behind PBX Direct Inward Dialing ATT: DIL 1 :l : ,DIL 1 :N: DISA TAFASl ,2: Attendant Console Direct In Line (13) Direct In Lines (1 :N) Direct Inward System Access Trunk Answer From Any Station Day mode: Change.Night receiving mode to Day receiving mode. Fixed: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can not change at Operator). Flexible: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can be changed at Operator). lf ATLC is installed, default value for Incoming Mode (Day) is AlT. l 4-21 l GROUP-TRUNK GROUP (2/2) Trunk Group No. 11 rI-- /C)$~“,‘~~~~~~~,N Default Value Set Data Item -+ cl” ” ‘“I’) None [7PCKUP - q 0 Pickup group No. (01 to 32) q EXT - 0 0 0 (7DN (3 or 4 digits) q ICM - 0 I&i group No. (1 to 8) cl” c flone q - blank PCKUP - 0 0 Pickup group No. (01 to 32) -n n n q DN (3 or 4 digits) j-JEXT fllCA.4 -.+ [7 ICM group No. (1 to 8) cl” -None q q ” blank PCKUP- 0 0 Pickup group No. (01 to 32) EXT - n n rl q DN (3 or 4 digits) [7lCM - 0 ICM group No. (1 to 8) blank -None q PCKUP- 0 0 Pickup group No. (01 to 32) q Ex-f ----, 0 0 0 q DN (3 or 4 digits) ----+ 0 ICM group No. (1 to 8) [7lCM blank - None cl” ” q PCKUP -, 0 [7 Pickup group No. (01 to 32) q EXT - 0 n n r]DN (3 or 4 digits) q ]ICM - 0 ICM group No. (1 to 8) blank cl” ” - None 0” q PCKUP- q 0 Pickup group No. (01 to 32) q EXT - 0 n n rlDN (3 or 4 digits) q ICM --+ 0 ICM group No. (1 to 8) .. blank - None 0”” q q PCKUP- 0 0 Pickup group No. (01 to 32) EXT --+ 0 0 0 [7DN (3 or 4 digits) rJICM -+ [7 ICM group No. (1 to 8) - None q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT - IlilllnDN (3or4digits) q ICM -+ q ICM group No. (1 to 8) blank cl” ” IID Digit Modification Table 0 1 digit (1 to 4) )BX Access Code with Pause Rclcl 00 0 )BX Access Code with Restriction q 00 0 1 IIJCI cl00 clocl Max.3digfis 00 0 cl (0 to 7) ZO Appearance Type q blank 00 0 Figures toto 9) q 0 0 0 0 0 q 00 0 0 0 Max. 3 digits [700 000 000 q IOC] Figures(O~W dax. Dial Nd. after EFA Signal blank blank 0 Single Single 0 Group 4-22 GROUP-TRUNK GROUP (I/2) Trunk Group No. 12 Item j We q DDD, q FEX. , Name :- - q WATS. q PVL, CPM g-J, Incoming/Outgoing /Ul ncoming only, 0 Outgoing only, 0 Both-way Incoming Mode (Day) 1OAT-T, ODEA, Incoming Mode (Night) / Intercept Routing (Day) in~7-r Intercept Routing (Night) ifl EYJ- -_--- (3 or 4digits), 0 None q DD co 1 02 FLEWLIE. q q q DIL 111, FIXW, q EXT - ( 3 i _pppmm q DIL l:~, ~TAFAS I, Both-way q TAWS 21 o r Flexible I ckligits), 0 N o n e 2 digits (01 to 16) . DIL vi ]Day Mode, ODISA None I None I 16 1 digit (1 to 8) Toll Restriction Table - Dialing Plan q CO-CO Duration Limit 1 Disconnect Time 0 1 . 5 s e c o n d s , 04.0 seconds Pause Time 01.5 Hook Switch Flash Time 080 mseconds, 0300 mseconds. 0900 mseconds, 01200 mseconds, Remark DDD: FEX: WATS: PVL: PBX: DID: q 3 digits (alphanumeric characters) - Tenant Toll Restriction Level Default Value Set Data .1 ]Type-A, 0 Type-B, 0 Type-C. 0 None o r minute(s) 2 d i g i t s seconds, 02.5 Direct Distance Dialing Foreign Exchange Wide Area Telecommunication Service Private Line Behind PBX Direct Inward Dialing ( 1 t o seconds, None 6 4 ) 10 1.5 03.5 seconds. 0 4 . 5 seconds q ATT: DIL 1:l: OIL l:N: DISA TAFASl, 2: 600 mseconds, ONone 3.5 None Attendant Console Direct In Line (1 :l ) Direct In Lines (1 :N) Direct Inward System Access Trunk Answer From Any Station Day mode: Change Night receiving mode to Day receiving mode. Fixed: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can not change at Operator). Flexible: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can be changed at Operator). l If ATLC is installed, default value for Incoming Mode (Day) is AlT. 4-23 l GROUP-TRUNK GROUP (212) Trrlnk o . 1 -2 . .-.... Groun _.. --r N._ D Default Value Set Data Item . -None II” ” ~~~~~~~~~~~~rN ‘““) C]PCKUP-+ flu Pickup group No. (01 to 32) FJExT - n [-I r[ r[DN (3 or 4 digits) ---+ a ICM group No. (1 to 8) FJ3A blank -FJ - - None q PCKUP, 0 0 Pickup group No. (01 to 32) - 0 [l ri nDN (3 or 4 digits) F--JXT JICM - a ICM group No. (1 to 8) blank q ” ” - None q PCKUP -110 Pickup group No. (01 to 32) q EXT --+ n r] n r]DN (3 or 4 digits) q lCM --+ 0 ICM group No. (1 to 8) blank - None cl” ” q PCKUP- 0 0 Pickup group No. (01 to 32) / q EXT -0 0 0 q DN (3 or 4 digits) ; q ICM - 0 ICM group No. (1 to 8) blank - None 0” ” q PCKUP- 0 q Pickup group No. (01 to 32) q EXT - 0 n n UDN (3 or 4 digits) q ICM -q ICM group No. (1 to 8) blank - None cl” ” q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT -0 q q q DN (3 or 4 digits) q ICM - 0 ICM group No. (1 to 8) cl” ” --c None 0”” q PCKUP--+O 0 Pickup group No. (01 to 32) q EXT - 0 0 0 q DN (3 or 4 digits) q ICM - 0 ICM group No. (1 to 8) 0IID Digit Modifmtiin Table 0 1 digit (1 to 4) P ‘BX Access Code with Pause q clcl q uu q ou q uu Max.3dWs Cl00 q CICI 000 q UU RweWtW q 0 0 blank ----j None q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT --+ 0 q 0 q DN (3 or 4 digits) q ICM - 0 ICM group No. (1 to 8) P‘BX Access Code with Restriction .. 0 0 17 blank blank 1 000 0 0 0 Maxa 3 di!@ hr Cr. Dial No. after EFA Signal q OU 000 q ICICI q UU Fkwres(OtW q (0 to 7) C ;O Appearance Type 0 Single f-J Group blank blank 0 Single 4-24 GROUP-TRUNK GROUP (l/2) Trunk Group No. 13 Item Set Data lo q DDD , FEX. q I --(01. 02 1Name Incoming/Outgoing 1incoming Mode (Day) Incoming Mode (Night) WAX, c?PvL, q PBX, q 3 digits (alphanumeric characters) c] incoming only, 0 Outgoing only, 0 Both-way I 1DA-IT, ~DISA, 001~ vi,q DIL I:N, q TARS I, q 1q Intercept Routing (Day) !ntercept Routing (Night) FLEXIBLE, q FIXED. q q A7-r q EXT- ( q EXT --+ ( 3 o r Toll Restriction Level 3 Day Mode, q o r 4digits), 4digils), 0 N o n e 1 Disconnect Time 01.5 s e c o n d s , 04.0 seconds Pause Time 0 Hook Switch Flash iime 080 m s e c o n d sm, s e0300 c o n d s ,0600 mseconds, 0900 mseconds,C]1200 mseconds, ONone Private Line PBX: Behind PBX DID: Direct Inward Dialing I 1 ! DIL ITI Type-C, q 2 minute(s) d i g i t s ( 1 None to 64) seconds,s e c o02.5 nds, Al-l-: DIL 1:l: Dft 1 :N: DISA TAFASl ,2: l : Flexible None / None I 1 CO-CO Duration Limit WATS: PVL: o 1 digit (1 to 8) Type-A, 0 Type-B, q Direct Distance Dialing Foreign Exchange Wide Area TelecommunicaGon Service c 16 q FEX: I 2 digits (01 to 16) Dialing Plan Remark DDD: TAFAS 21 0 N o n e - 1.5 DDD Both-way i CXA Toll Restriction Table o r I DID Default Value - None 10 1.5 s e03.5 c o n d s , 04.5 seconds 3.5 None Attendant Console Direct In Line (1 :l) Direct In Lines (1 :N) Direct Inward System Access Trunk Answer From Any Station Day mode: Change Night receiving mode to Day receiving mode. Fixed: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can not change at Operator). Flexible: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can be changed at Operator). l If ATLC is installed, default value for Incoming Mode (Day) is AlT. 4-25 a GROUP-TRUNK GROUP (2/2) Trunk Group No. 13 item Default Value Set Data -+ None CPCKUP-0 0 Pickup group No. (01 to 32) q EXT -n n n q DN (3 or 4 digits) q lCM --,q ICM group No. (1 to 8) blank - None cl” ” OPCKUP, 0 0 Pickup group No. (01 to 32) (?EXT -0 0 0 q DN (3 or 4 digits) q ICM - 0 ICM group No. (1 to 8) blank - None cl” ” [7PCKUP--+ 0 0 Pickup group No. (01 to 32) [TEXT --+ n 11 l-j r]DN (3 or 4 digits) q ICM -0 ICM group No. (1 to 8) blank - None PCKUP- 0 0 Pickup group No. (01 to 32) EXT -0 0 0 q DN (3 or 4 digits) ICM - 0 ICM group No. (1 to 8) blank - None cl” q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT -W 0 0 /J /JDN (3 or 4 digits) rJ2M - 0 ICM group No. (1 to 8) blank cl” ‘f$~~~~~~~~~rN ‘“I’) cl” q q q ” - None cl” ” q ]PCKUP- 0 0 Pickup group No. (01 to 32) q EXT -11 nDN (3 or 4 digits) q ICM - 0 ICM group No. (1 to 8) ri n - None 0” ” q PCKUP - 0 0 Pickup group No. (01 to 32) q EXT ----, n n n nDN (3 or 4 digits) q lCM ‘BX Access Code with Pause ‘BX Access Code with Restriction blank blank -B 0 ICM group No. (1 to 8) - None Cl” ” q PCKUP- 0 q Pickup group No. (01 to 32) q EXT - 0 0 0 flDN (3 or 4 digits) q ICM - 0 ICM group No. (1 to 8) IID Digit Modification Table 3 0 1 digit (1 to 4) 1 clclcl clclcl q clcl 0170 Max*3dWs q lCJCl q IIJCI q ICICI q lClClkwWtW 0 0 q 000 000 0 0 17 Max. 3 di@ IJCIO q ICICI q ICICI q ICICIRwWOto9) Max. Dial No. afler EFA Signal c l (0 to 7) 20 Appearance Type fJ Single 0 Group. blank blank blank 0 Single 4-26 GROUP-TRUNK GROUP (l/2) Trunk Group No. 14 Item Type q DDD, CFEX. Name - - Tenant Cl, WATS, q PVL, q q PBX. Incoming Mode (Night) [~FLEXIBLE, Intercept Routing (Day) OAIT Intercept Routing (Night) q DDD 3 digits (alphanumeric characters)’ co 1 Incoming only, 0 Outgoing only, 0 Both-way ]ATT, q q DISA, q q DIL 13. ]FIXED, q q DIL 1:~. q Both-way TAFAS I, •TAFA~~ EXT - ( 3 o r Day Mode, IJDISA Toll Restriction Table __ Dialing Plan q CO-CO Duration Limit 1 Disconnect 0 1.5 seconds, 4digits), Flexible None 0 N o n e None 2 digits (01 to 16) 16 1 digit (1 to 8) 1 Type-A, 0 Type-B, 0 Type-C, 0 None o r minute(s) 2 d i g i t s ( 1 t o None 6 4 ) 10 04.0 seconds 1.5 Pause Time ml.5 Hook Switch Flash Time [II80 mseconds. 0300 mseconds, 0 600 mseconds, 0900 mseconds,~1200 mseconds. ONone seconds, 02.5 Direct Distance Dialing Foreign Exchange Wide Area Telecommunication Service Private Line Behind PBX Direct Inward Dialing i:i DIL EXT - ( 3 o r 4 d i g i t s ) . 0 N o n e Toll Restriction Level Remark DDD: FEX: WATS: PVL: PBX: DID: IDID cl2 Incoming Mode (Day) Time q - q q Incoming/Outgoing Default Value Set Data seconds, 03.5 seconds, Al-T: DIL 1:l: DIL 1 :N: DISA TAFASl, 2: 04.5 seconds Attendant Console Direct In Line (1 :l ) Direct In Lines (l:N) Direct Inward System Access Trunk Answer From Any Station Day mode: Change Night receiving mode to Day receiving mode. Fixed: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can not change at Operator). Flexible: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can be changed at Operator). ff ATLC is installed, default value for Incoming Mode (Day} is ATT. l 4-27 3.5 None l GROUP-TRUNK GROUP (212) Trunk Group No. 14 lestination (DIL 1: N only) Type and Number Default Value Set Data Item cl” ” -None q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT - n 0 0 q DN (3 or 4 digits) q ICM -+ C ICM group No. (1 to 8) blank -None 0” ” q PCKUP-, 0 q Pickup group No. (01 to 32) q EXT - u n n nDN (3 or 4 digits) /--JICM -----, iJ ICM group No. (1 to 8) blank cl" " ----* None q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT 3 n n n r]DN (3 or 4 digits) q ]ICM - 0 ICM group No. (1 to 8) 0” - blank r None q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT -+ ri n r-1 ~DN (3 or 4 digits) q ICM - 0 ICM group No. (1 to 8) blank - None cr” OPCKUP - 0 [7 Pickup group No. (01 to 32) q EXT - 0 rl n r]DN (3 or 4 digits) q ICtVl - [7 ICM group No. (1 to 8) - None cl” ” q PCKUP --+ 0 0 Pickup group No. (01 to 32) q EXT -q 0 0 q DN (3 or 4 digits) q ICM 3 0 ICM group No. (1 to 8) - None Cl” ” [~PCKUP-B 0 0 Pickup group No. (01 to 32) q EXT -+ 0 0 0 q DN (3 or 4 digits) f-J34 ---+ 0 ICM group No. (1 to 8) 0”” IID Digit Modifiitiin Table ‘BX Access Code with Pause ~BXAccessCodewithRestriction hx. Dial’No. after EFA Signal :O Appearance Type .. blank blank ---+ None q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT --+ 0 0 0 q DN (3 or 4 digits) /--&M blank blank - 0 ICM group No. (1 to 8) 0 1 digit (1 to 4) 1 q lrJcl q cKl 000 q oo Max-3dWs q UU q UCI 000 ClUEI FiguWOto9) q o n 000 000 000 Maxv3d@fis q ClCl q IUCI q CIU q IJCI QwesPto9) q (0 to 7) 0 Single q Group 4-28 blank blank 0 Single GROUP-TRUNK GROUP (112) Trunk Group No. 15 Item We q DDD, Name - - Tenant cl’* 1IncomingiOutgoing Incoming Mode (Day) Incoming Mode (Night) Intercept Routing (Day) Intercept Routing (Night) 1 Toll Restriction Level Toll Restriction Table ’ Default Value Set Data q EX. q WATS, OWL. q PBx, q DID 3 digits (alphanumeric characters) - cl2 10 Incoming OAT-I-, q co I DISA, q DIL 19. q DILI:N, •TAFA~ I, ~TAFAS~! q FLEXIBLE. q VXED, IDay Mode, IJIXA q Arr q Ex-r- ( 3 o r 4digits). 0 N o q EXT --+ ( 3 o r 4digits), q None I - - DLL I 1:l Flexible None I 16 I 1 Disconnect Time 0 1 . 5 s e c o n d s , 04.0 seconds 1.5 Pause Time q 1.5 seconds, 3.5 Hook Switch Flash Time 080 mseconds, 0300 mseconds, 0 600 mseconds, ( 1 t o mseconds, ONone Remark Et? WATS: PVL: PBX: DID: 6 4 ) 0 2 . 5 s e c o n d s , 03.5 s e c o n d s , 04.5 seconds 0900 mseconds.nl200 Direct Distance Dialing Foreign Exchange Wide Area Telecommunication Service Private Line Behind PBX Direct Inward Dialing Al-r: DIL 1:l: DIL 1 :N: DISA TAFASl , 2: . Attendant Console Direct In Line (1 :l) Direct In Lines (1:N) Direct inward System Access Trunk Answer From Any Station Day mode: Change Night receiving mode to Day receiving mode. Fixed: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can not change at Operator). Flexible: Incoming call only arrives on either DN which set by Night Answer point of Trunk or External pager of Universal Night Answer (Can be changed at Operator). if ATLC is installed, default value for Incoming Mode (Day) is An. l 4-29 : I None CO-CO Duration Limit minute(s) 2 d i g i t s 1 1 1 digit (1 to 8) o r l None n e 2 digits (01 to 16) - 1 /Both-way only, 0 Outgoing only, 0 Both-way lo Type-A, 0 Type-B, 0 Type-C, 0 None Dialing Plan DDD I 10 None _- GROUP-TRUNK GROUP (212) Trunk Group No. 15 estination (DIL 1: N only) Type and Number Default Value - Set Data Item - None 0 ” ” q PCKUP- 0 E Pickup group NO. (01 to 32) q JEXT - rj n n rjDN (3 or 4 dtgits) q ICM - 0 ICM group No. (1 to 8) blank -None PCKUP, 0 IJ Pickup group No. (01 to 32) --, r\ n n nDN (3 or 4 digits) EXT cl” ” q q j-JlCM --, 0 ICM group No. (1 to 8) 0” * -None blank q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT -q q 0 q DN (3 or 4 digits) q ICM -.+ 0 ICM group No. (1 to 8) blank ----+ None cl” ” q PCKUP ----+ q 0 Pickup group No. (01 to 32) q EXT - r-j ri rl F]DN (3 or 4 digits) q ICbl -q ICM group No. (1 to 8) blank -None Cl” ” q PCKUP - 0 0 Pickup group No. (01 to 32) TEXT -., 0 q 0 q DN (3 or 4 digits) q ICM c 0 ICM group No. (1 to 8) blank - None cl” q ]PCKUP- 0 q Pickup group No. (01 to 32) q EXT - 0 r] ri rjDN (3 or 4 digits) q lCM 3 0 ICM group No. (1 to 8) blank -None cl” ” q q PCKUP- 0 0 Pickup group No. (01 to 32) ]EXT --+ n n n nDN (3 or 4 digits) ---+ 0 ICM group No. (1 to 8) fJlCM blank -None cl” q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT - 0 l-l r[DN (3 or 4 digits) q ICtVl - 0 ICM group No. (1 to 8) blank n IID Digit Modification Table 0 1 digit (1 to 4) ‘BXAccess Code with Pause cl00 clclo 1 000 000 Max-3Ws 000 00 0 00 0 00 0 Figures PBX Access Code with Restriction 0 q 0 000 q ICICI q ICICI Max. Dial No. after EFA Signal c l (0 to 7) CO Appearance Type 0 Single 0 Group 00q blank Tog) 0 0 0 Max. 3 digits q ICICI q ICIIJFWWOto9) blank 0 Single 4-30 GROUP-TRUNK GROUP (2/2) Trunk Group No. 16 Default Value Set Data Item q q - None PCKUP- 0 q Pickup group No. (01 to 32) EXT - n n n/JON (3 or 4 digits) -q ICM group No. (1 to 8) j--JCM blank - None cl” q PCKUP - 0 0 Pickup group No. (01 to 32) q EXT -, 11 n r[ nDN (3 or 4 digits) q ICM -----+ 0 ICM group No. (1 to 8) blank - None cl” ” q PCKUP- 0 0 Pickup group No. (01 to 32) q EXT --+ 11 n n f-ION (3 or 4 digits) q lCM - 0 ICM group No. (1 to 8) blank cl” ” )f$~~f~,$~~~~rN ‘“I’) 0” - - None q PCKUP - 0 0 Pickup group No. (01 to 32) q EXT -O/-JuODN(3or4digits) q ICM -V 0 ICM group No. (1 to 8) blank -None cl” ” q PCKUP - 0 c] Pickup group No. (01 to 32) q EXT ---, 0 n n nDN (3 or 4 digits) q ICfVl - [7 ICM group No. (1 to 8) 0”” . None - blank :;%;UP- 0 [7 Pickup group No. (01 to 32) - n n r-j q DN (3 or 4 digits) rJzM -+ 0 ICM group No. (1 to 8) blank - None cl” ” q PCKUP - 0 0 Pickup group No. (01 to 32) q EXT - 0 0 0 q DN (3 or 4 digits) j--&M - 0 ICM group No. (1 to 8) blank - None cl” ” q PCKUP - 0 0 Pickup group No. (01 to 32) q EXT - 0 0 q q DN (3 or 4 digits) f-JICM - 0 ICM group No. (1 to 8) blank 110 Digit Modification Table 17 1 digit (1 to 4) ‘BX Access Code with Pause 000 ‘BX Access Code with Resiriction q ICICI Cl00 000 000 FiguresPto9) q q [7 Max. 3digfis 0q 0 00q 0 00 0 0 0 Cl 0 0 0 0 0 0 q 0 Figures (Otog) .‘I 000 Max. Dial No. after EFA Signal c l (0 to 7) 20 Appearance Type 0 Single 0 Group 1 000 000 Max.3Ws blank blank 0 Single 4-32 GROUP-ICM/PAGING GROUP Item Default Value Set Data 1 c] Tenant 1, 0 Tenant 2 2 c] Tenant 1, [7 Tenant 2 3 0 Tenant 1. 0 Tenant 2 4 [7 Tenant 1, 0 Tenant 2 5 0 Tenant 1, 0 Tenant 2 6 0 Tenant 1, 0 Tenant 2 7 0 Tenant 1, 0 Tenant 2 8 0 Tenant 1, [7 Tenant 2 1 0 Tenant 1. 0 Tenant 2 2 0 Tenant 1, 0 Tenant 2 3 0 Tenant 1, 0 Tenant 2 4 0 Tenant 1, 0 Tenant 2 5 0 Tenant 1, 0 Tenant 2 6 0 Tenant 1, q Tenant 7 q Tenant 1, 0 Tenant 2 8 0 Tenant 1. 0 Tenant 2 . ICM Group Tenant 1 Tenant 1 PAG Group 4-33 2 Call ‘ickup Ziroup 01 I GROUP-CALL PICKUP GROUP Set Data ICM Group Number UCD Group Number ‘aging Group Number Call Tckup 3roup ICM Group Number ‘aging Group Number 18 03 - 19 -- -- 20 04 05 - 21 -- - -- 22 06 23 07 - 08 - 24 09 - 25 10 - 11 - 12 - -- 26 -- -- -- 27 28 -- -- 29 13 14 - 30 15 - 31 16 - 32 Note: Selection of Value 1Default Value 1 I UCD Group Number 17 - 02 i Set Data ICM Group Number 1 digit (1 to 8) UCD Group Number 2 digits (01 to 32) or space (no belonging) blank Paging Group Number _ 1 digit (1 to 8) or space (no belonging) blank 1 c 4-34 -- - 5. Trunk TRUNK-CO LINE - - Trunk Equipment Number Default Value Item Trunk Group (2 digx 0x0 16) , TrunkName - q Direct Termination - - - DN (3 or 4 digits) - - - ONone _ _ q _ _ _ _ q _ - _ _ q DN (3 or 4 digils) - - - ONone - - - ONone q q DTMF PiJlse q q DTMF Pulse 080 mseconds 080 mseconds Duration Time 0160 mseconds 0160 mseconds q DTMF Speed Break CPC Detection q q LOW (10 pps) High (20 pps) OLOW (1Opps) aHigh (20 pps) 060% 067% _ _ _ _ DN (3 or 4 digits) - - - _ ONone EEOo - q RMT ONone q q DTMF Puts.e - [IIRMT ONone q q IDTMF Pulse (2 digits: 01 to 16) (2 digits: 01 lo 16) (2 digits: 01 to 16) (2 digits: 01 to 16) - _ q _ _ _ DN (3 or 4 digits) - - - ONone ONone _ q _ _ - - q DN (3 or 4 digits) DN (3 or 4 digits) q _ _ DN (3 or 4 digits) - - - _ ONone _ _ - -~ ONone EIUNAI. •UNA~ EXT (3 or 4 digits) q q q _--- -___ _ _ q RMT ONone q RMT ONone lUNAl.•UNA~ EXT (3 or 4 digits) q q _ _ RMTONone IUNAI , •UNA~ EXT (3 or 4 digits) _ q q DTMF [lPulse q DTMF ~-IPulso q DTMF [- -]f’illsc~ q _ DTMF I-1Ptrlr.c~ 080 mseconds ~160 mseconds 080 mseconds 0160 mseconds 080 mseconds 0160 mseconds 080 mseconds 0160 mseconds q LOW(1Opps) OHigh (20 pps) alow (1Opps) UHigh (20 pps) q JLOW (1Opps) UHigh (20 pps) nLow(lOfys) OHigh (20 pps) rlLow (10 pps) IJHIgh (20 PPS) mow (10 PPS) UHlgh (20 pps) q cl% 060% Lxio% LAO% I&0% LA 60% 067% 067% [767% 067% r j67% ONone .~ -. with ATLC: blank CO: Ext. No DTMF 80 m67% u6.5 mseconds u6.5 mseconds U8 x -/msec. 08 x -/msec. ONone ONone q llmmediate Stari IJlmmediate Start DImmediate Slarl immediate Start IJlmmediate Start q immediate Start q immediate Start Olmmediate StarI USend Delay Wink USend Delay Wink USend Delay Wink USend Delay Wink q Send Delay Wink USend Delay Wmk USend Delay Wink USend Delay Wink I q Co: Ext. N o _ _ RMT ONone 080 mseconds 0160 mseconds ONone DID: 1 6 _ _ - - ONone 06.5 mseconds u6.5 mseconds -/msec. 08 x /msec. ONone ONone co: 01 Txxxx _ physlca, Number - -----____ _ 080 mseconds 1&l mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds 08 x-lmsec. 08 x Imsec. 08 x-lmsec. 08 x-lmsec. 08 x ONone DID start Arrangement _ DN (3 or 4 digits) -___ --__ q RMT ONone IJRMT IJNone Dial Mode % (2digits: 01 to 16) q UNAi, q luNA2 q ~NAI, •UNA~ q IuNA~, q lutdA2 q uNAi, •UNA~ q IUNAI , •UNA~ q EXT (3 or 4 digils) q EXT (3 or 4 digits) (JEXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) q F$L: Answer Pulse (2 digiis: 01 to 16) -----________ ---_-------_----_------ (Type1No.J (2 digiis: 01 to 16) 50 (400ms) Send Delay Wink TRUNK--CO LINE Trunk Equipment Number Default Value Item Trunk Group Trunk Name - (2 digits: 01 to 16) - - - - - - - - - - - --bb_____ Direct Termination - F$ Answer (Type: No.) Dial Mode - (2 digits: 01 10 16) A - - ODN (3 or 4 digits) q --_- ONone ONone - - (2 digils: 01 lo 16) (2 digits: 01 to 16) (2 digits: 01 to 16) - co: 01 DiD: ‘6 Txxxx .- ONone - - - (2 digib: 01 lo 16) -_-_~-.-. _ q - - (2 digits: 01 lo 16) _ - -. -_.. OLIN (3 or 4 digits) DN (3 or 4 digits) - (2 digils: 01 lo 16) rtlyw:;ll - - - - DN (3 or 4 digits) - q - - - - DN (3 or 4 digils) - q - - - DN (3 or 4 digits) _ _ q - - _ ---_--Number DN (3 or 4digits) [7DN (3 or 4 digits) _--- _--- --_- -___ _ ONone ONone ONone ONone _ _ ONone _ ~0: ant, No, with ATLC: blank q q luw q uNA2 q luNAi,•UNA~ q UNA~,•UNA~ OUNAl. •UNA~ CIUNAI, •UNA~ q IUNAI,•UNA~ q UNAI,•UNA~ q lUNAi.•UNA~ EXT (3 or 4 digits) q EXT (3 or 4 digiis) OEXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) OEXT (3 or 4 digits) q EXT (3 or 4 digits) q RMTONone - - - - - - _ - - _ - _ _ _ _ - _ _ _ _ q -.-T-.-o-ne- q RMT-uNone - - - - ODTMF IJPulse q q q RMT ONone DTMF lPulse q RMT ONone ORMT ONone q DTMF c]Pulse ODTMF q PlJls.e IJRMT ONone :zt- q DTMF IJPulse q DTMF n Pulse q RMTONone q DTMF OPulse CO: Ext. No. DTMF 080 mseconds 080 mseconds 080 mseaxds 080 mseconds cl80 mseconds DTMF 080 mseconds 080 mseconds bm mseconds Duration Time OfsO mseconds OlsO mseconds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds a160 msecxnds 0160 mseconds Pulse Speed IJLOW (10 PP4 OH@ (20 pps) q LOW (10 Pps) q High (20 p) OLOW (10 w q Huh 6’0 PPS) q LOW (10 FM q High (20 PPS) IJLOW (1Opps) q High (20 pps) q q ILOW (10 pps) High (20 pps) q ILOW(10 PF4 Thigh (20 PIN 8’ q LOW (10 pps) OHigh (20 pps) % Break cpc DeWh DID start Arrangement q 06.5 mseconds 06.5 mseamds 06.5 mseconds 6:5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds Imsec. 08 x-Imsec. 08- x /msec. 08x-/msec. 08 x-lmsec. 08 x-lmsec. :ilnFImsec. 0 8 x _ Imsec. ONone ONone ONone ONone ONone ONone EiiZ”F 5. (400ms) q immediateSlarl q immediate Stafl I-Jlmmediate Slari lmmediaieStart q immediateSlati q immediateStart q immediateSlarl q immediateSlarl O%nd Delay Wink OSertd Delay Wink USend Delay Wink q Send Delay Wink USend Delay Wink USend Delay Wink aSend Delay Wink (ZlSend Delay Wink -Iq -__ Send Delay Wtnk TRUNK---CO LINE Tnunk Equipment Number Default Value Item Trunk Group (2 digz Oxo 16) TrunkName F!k: *wwer (Typ:No.) Dial Mode DTMF Duration Time Pulse speed % Break CPC Detection DID start Arrangement - - - - ODN (3 or 4 digits) - - (2 digiis: 01 lo 16) - - (2 digits: 01 lo 16) (2 digits: 01 lo 16) (2 digits: 01 to 16) ~-~~~~~~~--~-~----- Direct Termination - - - q w q - - - - (2 digits: 01 lo 16) DN (3 or 4 digits) _--- KINone q DN (3 or 4 digits) - q INOW q luNA2 IJuNAi, OUNA~ qT (3 or 4 dgils) q EXT (3 or 4 digiis) q - - - [JNone - - - Number - ---------_-_ flDN (3 or 4 digits) nDN (3 or 4 digits) --_- --_- -_-_ I ~-INono KINone co: 01 DiD: 1 6 _ _ 1 1Nont1 nDN (3 or 4 digils) _ ---~-“N!?L - Co: Ex, No with ATLC: thnk ~~.._.._~ ~~-. - q UNAI, OUNA~ OuNAl, 0~~2 •~NAI, CluN~2 OUNAI, TUNAS C~UNAI, UUNA~ II-IUNAi, IIuNAz EXT (3 or 4 digib) q EXT (3 or 4 digits) q IEXT (3 or 4 digits) q EXT (3 or 4 digits) CO: Ext. No __--___---___----_-__--_- ___. _ _ _ _ -.-. q RUTONone q RMTONone ORMT aNone ORMT ONOIM ORMT ONone q RMT ONone ORMT ONone q RMT ONone q q uNAi, - ODN (3 or 4 digits) nDN (3 or 4 digils) (2 digits: 01 to 16) Txxxx - --_-_-----_____ physical __--___-_ --_--_____ - - q (2 digirs: 01 lo 16) DTMF IJPulse q q DTMF Pulse q EXT (3 or 4 digiis) IJEXT (3 or 4 digits) q DTMF IJPulse q DTMF 0Puls.e I -IDTMF OPulse ODTMF OPulse 080 mseconds 080 msewnds 080 mseconds 080 mseconds 080 mseconds 16Omseamds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds q q ILOW(10 PP4 q Mth(20 pps) chow (fOpw OHM (20 PIN q LOW (10 PPd q Hish(20 W OLOW (1Opps) OHigh (20 pps) OLOW (lOPr4 Eiz0 ~~ :Ki E? Oo EE O.2 q High(20 w) q 1 IDTMF I ImN U Pulse U Pulse 080 mseconds 080 mseconds 080 mseconds bO mseconds ml60 mseconds 0160 mseconds q LOW (IO pps) OHigh (20 pps) FE Oo q LOW (IO pps) Thigh (20 w) IJLOW (10 pps) q High (20 pps) cbo% fl67% 060% n67% - 06.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds OS.5 mseconds 06.5 mseconds 06.5 mseconds 08 x :;ln, Imsec. 0 8 x _ /msec. /msec. 06x-lmsec. 08x-/msec. 08x-/msec. 08x-/msec. 08x-/msec. ONone ONone ONon; C]None ONone ONone ONone q q immediate Start Send Delay Wink q q immediate Start Send Delay Wink q q Olmmediale SIari Ulmmediale Start IJlmmediale Slarl immediate Start IJlmmedide Slarl ~lmmf3diale Slarl bnd Delay Wink USend Delay Wink bnd Delay Wink aSend Delay Wink USend Delay Wink aSend Delay Wink DIMI 8o - (40500,s) Send Delay Wink TRUNK&CO LINE Trunk Equipment Number Default Value Item TrunkGroup (2 clgils: 01 lo 16) (2 digits: 01 lo 16) TrunkName ----- (2 digits: 01 to 16) (2 digils: 01 lo 16) ----- - - - - - - - - - (2 digits: 01 lo 16) - - (2 digits: 01 IO 16) (2 digits: 01 lo 16) q - - q h - OuM1,q luNA2 Fzkl: Answer (Type:No.) - DN (3 or 4 digiis) OWT (3 or 4 digils) q q DN (3 or 4 digits) DN (3 or 4 digits) q q DTMF Pulse DN (3 or 4 digits) _--- ---_ _--_ _ ONone ONone ONone •UNA~, •UNA~ EXT (3 or 4 digiis) q q Txxxx -______. Physical Number -________ q DTMF OPulse _ q _ _ ONone - - DN (3 or 4 digits) nNono _ q q DN (3 or 4 digits) _ _ nNone _ _ DN (3 or 4 digits) _ nNone _ _ q uNAi,•UNA~ q luNAi , •UNA~ q luN~i, •UNA~ q ~NA~. TUNAS luN~l,•UNA~ q luNAi,•UNA~ EXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) IJEXT (3 or 4 dig&) :FTlz U DTMF 080 msaconds 080 mseconds 080 mseconds Duration Time 0160 msecOnds ~160 mseconds 0160 mseconds q ---_ __-_ _ _ FIMT ONone q RMT ONone q RMTONone DTMF Pulse q q DTMF Pulse q _ _ RMTONone _ Co: Ext, No, with ATLC: blank q LOW(1Ojlps) OHigh (20 pps) q ILOW (10 pps) OHigh (2fJ PPS) q 060% 067% 060% 067% 060% 067% 060% 067% 06.5 mseconds 08x-/msec. ONone 06.5 mseconds 08x-lmsec. ONone 06.5 mseconds 08x-/msec. ONone 06.5 mseconds 08x-lmsec. ONone % Break 060% 067% 060% 067% CPCDetedon 06.5 mseconds 08x-Imsec. ONone OS.5 mseconds 08x /msec. NonF DID start Arrangement Olmmediate Slarl IJlmmediale Slarl q lmmediie Start q lmmediate.Starl Olmmediale Start O&r-d Delay Wink OS& Delay Wink OSertd Delay Wink aSend Delay Wink q Send Delay Wink Thigh (20 PPS) lizz 0 06.5 mseconds 08x-lmsec. ONone q q q OLOW Wpps) q Hish(20 pps) OLOW (10 pps) ODTMF q Pulse q CO: Ext. No. _ _ RMTC]None q LOW (10 PIN q HM (20 PIN q LW (10 f.w q High(20 PI@ 06.5 mseconds 08x- Imsec. ONone _ DTMF q DTMF Pulse 0 Pulse -.. -__.~- _ ._._ - - .~_ _~ US0 mseconds 080 mseconds 080 mseconds 080 msewnds 080 mseconds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds l-J160 mseconds q q Pulse Speed q q DN (3 or 4 digits) q -we- _--- _--- q IRMT ONone q IRMT ONone q RMT ONone Dial Mode q co: 01 DlD: ‘ 6 ------______- ------------------------__-_--Direct Termination (2 digits. 01 IO 16) ILOW (10 pps) 0 High (20 pps) immediateStati DImmediate Start Elmmediate Start OSend Delay Wink c]Send Delay Wink USend Delay Wink DTMF ” - (405ooms) Send Delay Wink TRUNK&CO LINE Trunk Equipment Number Default Value Item --. --.-. TrunkGroup TrunkName - - - - - - - - - - - - - ONone (2 digits: 01 to 16) - (2 digits: 01 to 16) - (2 digits: 01 to 16) (2 digits: 01 to 16) (2 digits: 01 to 16) _--_-----_-___-__-_____ - - - - - q DrJ (3 or 4 digits) q Direct Termination - - - DN (3 or 4 digits) _ _ - ONone - - q - - - - - q DN (3 or 4 digits) - - - - DN (3 or 4 digits) - q - - - - DN (3 or 4 digits) - _ - _ - - - - - - ONone ONone ONone - q _ _ _ _ _ q DN (3 or 4 digits) - - _ _.. l%one -- .-._. . ..- ~..--~.~.--. -.. -... - - (2 digits: 01 to 16) - - - - q Dial Mode - - ---a-e-v _ RMT ONone /gTlr U q RMT ONone iFTlr U Pulse Speed q LOW (10 WI q H@ POpps) % Break 060% 0 8 ONone q LOW(1Opps) OH@ GQ w) PIE0 067% 06.5 mseconds Detection DID start Arrangement DID1 1 6 Txxxx __._... physlcnl - _ ------_Number q lDN (3 or 4 digits) IDN (3 or 4 digits) Co: Ext. No with ATLC: blank _ __ __ _ [-INone [-INone ~~.. q q q RMTONone DTMF lPulse _ q _ _ -_-__---_ RMT ONone’ ORMT ONone :pDTz: U q q DTMF lPulse ORMT ONone q q _ DTMF Pulse q q q _ _ RMTONone _ q q q DTMF Pulse _ _ RMT ONone _ DTMF DTMF Pulse DTMF 080 mseconds 080 mseccnds 080 mseconds 080 mseconds 080 mseconds 080 mseconds 080 mseconds 080 mseconds Duration Time 0160 mseconds fll60 mseconds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds oi60 mseczonds cpc c o : 01 q IL~NAI, q UNM q IUNAI, q luNA2 q luNAi, q uNA2 q luNAi, •UNA~ OUNAi, •UNA~ ~UNAI, nUNA DUNAl, q UNA2 IJUNAi, •UNA~ q EXT (3 or 4 digits) OEXT (3 or 4 digiis) OEXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) nEXT (3 or 4 digits) q UT (3 or 4 dig&) CO: Ext. No F$ Answer (Typ:No.) (2 digits: 01 to 16) (2 digits: 01 lo 16) q LOW (10 PIN OHM (20 IV) 060% 067% q LOW (10 pps) OHigh (20 pps) 060% 067% q LOW(1Opps) OHigh (20 pps) I%7Oo q q LOW(1Opps) High (20 pps) 060% 067% US.5 msecands 0 6 . 5 mseccnds 06.5 m s e c o n d s 06.5 m s e c o n d s 06.5 mseconds 08 X-/mm. 0 8 x-/msec. 08 x-/msec. 08 x-/msec. 08 x-/msec. ONone ONone ONone ONone ONone X-/msM. DImmediate Stti q Send Delay Wink q q immediate Start q immediate Startq llmmediate Start ISend Delay Wink USend Delay Wink aSend Delay Wink IJlmmediate Start DImmediate Start Send Delay Wink q Send Delay Wink q q q LOW (10 pps) High (20 pps) 060% n67% 06.5 mseconds 08 x -/msec. ONone q q a’ ILlLow (10 Pps) q High (20 pps) _ 060% 067% - 06.5 mseconds 08 x ONone /msec. immediate Start DImmediate Stati ]Send Delay Wink q Send D&y Wink (4Ot-L) Send Delay Wink TRUNK&CO LINE Trunk Equipment Number - Default Value Item Trunk Group Trunk Name F’$“” Answer (Type: No.) Dial Mode - - - - (2 digits: 01 to 16) (2 digits: 01 to 16) - - - (2 digits: 01 to 16) (2 digits: 01 lo 16) - - - - ODN (3 or 4 digits) - - - - ITIM v q _ - _ - DN (3 or 4 digits) - nNann - - q - - - - DN (3 or 4 digits) - _ q - - - _ DN (3 or 4 digits) --A-nNone nNone - - _ q _ _ - _ DN (3 or 4 digits) % Break DID start Arrangement co: 01 - (2 digits: 01 to 16) DtD: 1 6 Txxxx Phys,cn, q _ _ DN (3 or 4 digits) nNoncl nNOll0 _ _ q _ _ _ DN (3 or 4 digits) _ _ I-lNOlW _ _ _ _ _ _ _ flDN (3 or 4 digits) _ _ rlNOfl0 _ _ OUNAl, OUNA2 IJuNAl, •UNA~ QuNAI, q UNA;! DuNAl, •UNA~ q uNAi, CluNA2 UUNAi, UUNA~ L3UNAi. OUNA~ ’ OUNAI, LjUNA2 DEXT (3 0r4 dighS) q EXT (3 or4 digits) q EXT (3 or4 digits) q EXT (3 or.4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) DEXT (3 or 4 digits) OEXT (3 or 4 dgrts) O~T-~None :;Tl!: U ORMT ONone :Ez U -. -- - .-. -. _b__ _-_- --_o&T ONone ~RMT ORMT ONone ORMT ONone q DTMF OPulse q q DTMF Pulse IJDTMF OPulse OLOW (10 WI CIL~ (low) q LOW (10 pps) tlh-th (20 pps) Thigh (20 pps) OH@ @J pps) q LOW (10 PPd q H@ PQ PPS) q LOW (10 FP) OH@ (20 PPS) Ezz EiKi :iK :z O-3 EYE mseconds 06.5 mseconds 06.5 mseconds OS.5 mseconds OS.5 msecwds 08x-Imsec. 08x Imsec. 08x-lmsec. 08x-lmsec. 08x-/msec. ONone ONone ONon; ONone ONone 06.5 CPCDetection _ ---__-___ 080 mseconds 080 mswnds DTMF 060 mseconds 080 mseconds 080 mseconds Duration Time 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds Pulse Speed (2 digits: 01 to 16) (2 digits: 01 to 16) ------~ ____----------- - - - - - - - - - _ _ - _ - - _ - - - - _ - - - _ - - - - -__ - - _- _ _ ._- _-_ .__ _ _ _ _ _ .., b Direct Termination - - (2 digits: 01 to 16) nNone rJRMT KINone [TIRMT ~DTMF FIDTMF UPulse U Pulse UPulse 080 mseconds 0160 mseconds 080 mseconds 0160mseconds 080 mseconds 0160 mseconds q q q q q High (20 pps) LOW (10 pps) High (20 pps) co: Ext, No, with ATLC: blank CO: Ext. No. [-INone ~DTMF LOW (10 pps) Number DTMF 80 LOW (10 pps) OHigh (20 pps) 060% 060% 067% 067% 060% 067% US.5 mseconds 06.5 mseconds 06.5 mseconds 08x-/msec. ONone 08x-lmsec. ONone 08x-/msec. ONone Olmmediale Start Olmmediate Start q llmmediate Start IJlmmediate Start (JImmediate Start /JImmediate Start Olmmediate Start ntmmediate Start O~end Delay Wink q &d Delay Wink q %td D&y Wink USend iMay Wink USend Delay Wink USend D&y Wink OS-end D&y Wink q &nd Delay Wink - (40%) ___-Send Delay Wink TRUNK420 LINE Trunk Equipment Number’ Item drunk Group - - (2 digiis: 01 to 16) TrunkName - - (2 digits: 01 to 16) q - - - - - DN (3 or4 digii) - - - ONone q - - - - (2 digits: 01 to 16) - - -----_----___-DN (3 or 4 digits) ONone - q - DN (3 or 4 digits) ONone - - - (2 digits: 01 to 16) q q ONone ONone DN (3 or 4 digits) DiD: 1 6 Txxxx ----_---___ Physical _ q - - co: 01 - -----___- ODN (3 or 4 digits) - - (2 digits: 01 to 16) DN (3 or 4 digits) _ _ _ Number _ DN (3 or 4 digits) Co: Eti. No, with ATLC: _--- ___- ___blank ONone ONone q luhMi, q luNA2 EluNAi, •UNA~ q lu~Ai,OUNA~ q luN~i,•UNA~ q uNAt,RUNA;! q uNA~,q ~NA~ OuNAi, •UNA~ q luNAi,•UNA~ q lEXT (3 or 4 digits) q EXT (3 or4 digits) OEXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) iJEXT (3 or 4 digits) q EXT (3 or 4 digits) CO: Ext. q- Dial Mode q q - -UNone - - l$iiyjG,u UllMI-~~~n- ~..IHMII_JG,l”- 1 Ir,,Ir 1; RM -T ONone-ORMT - -ONone ORMT xUNone - UHMl DTMF Pulse 080 mseconds Duration Time 0160 msecwrds DTMF % Break q DN (3 or 4 digits) Fyp: No*) Pulse Speed (2 digits: 01 to 16) ~~~--~~~~-~~--~----- ONow Ftgii Answer (2 digits: 01 to 16) - (2 digits: 01 to 16) --w-s__---Direct rermination Default Value , q LOW (10 PFN OHi@ (20 PIN Ez q q DTMF Pulse q q DTMF Pulse 080 mseconds 080 msecnnds 0160 mseconds ~160 mseconds OLW WPW q E? ET0 q High (20 pps) LOW(1Opps) q HM (20 w) ODTMF q Pulse ~DTMF q Pulse ~DTMF ~~DTMF UPulse U Pulse 011l1 - ~DTMF UP&Se DTMf- 080 msecnnds 080 mseconds 080 mseconds 080 mseconds 080 msecnnds ~160 mseconds 0160 mseconds 0160 msecands 0160 mseconds 0’160 mseoonds q LOW(1Opps) OHM (20 PPS) Ez OH@ (20 PPS) OLOW (1Opp.) OHigh (20 pps) q ILOW (10 pps) OHigh (20 pps) q 060% cbo% 060% ckm 067% 067% IJLOW (1Opps) 067% q No 6’ LOW (10 pps) High (20 pps) 067% I 06.5 CPCDetection DID start Arrangement msaconds OS.5 msecnnds OS.5 mseconds a6.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds 08x-Imsec. 08x-/msac. 08x-/msec. 08x-lmsac. 08x-/msec. 08x-/msec. 08x-Imsec. 08x-/msec. ONone ONone ONone ONone ONone ONone ONone ONone q llmmediate Start q llmmediate Start IJlmmediate Start Olmmediate Start Olmmediate Stan q immediate Stan Owed Delay Wink USand Delay Wink OSend Delay Wink USend Delay Wink USend Delay Wink USend Delay Wink q DImmediate Stan (-Jlmmediale Start Send Delay Wink USend Delay Wink (405aoms) Send Delay Wtnk TRUNK&CO LINE Trunk Equipment Number Default Value Item drunk Group rrunkName 3irect rermination - - (2 digits: 01 lo 16) - - - - q - Fii; Answer - - (2 digits: 01 to 16) - (2 digits: 01 to 16) -7_____ - a - - - q DN (3 or 4 digits) - - _ - - _ DN (3 or 4 digits) - - q - _ - - - e m DN (3 or 4 digils) q _--_ ONone - - - (2 digits: 01 to 16) (2 digits: 01 to 16) - - - _ - - - - q DN (3 or 4 digits) ONone - - - - (2 digils: 01 to 16) - - DN (3 or 4 digits) - - - _ - - - - - q DN (3 or 4 digits) - - - - - (2 digits: 01 to 16) (2 digits: 01 lo 16) Txxxx - - Phystcal - --______-Number q _ - - - DN (3 or 4 digits) - _--- -.-,-..--_ ---_ONone ONone ONone - _ q _ _ DN (3 or 4 digits) _ _ ONone _ _ ONone ONone •UNA~, q uNA2 •UNA~, q lutw q lUNAi, q uNA2 q UNAI, q uNA2 q uNAi, •UNA~ EluN~i. UUNA~ KluNAi, OUNA~ IIluNAi. TUNAS q EXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) q EXr (3 or 4 digits) []EXr (3 or 4 digits) [ )EXT (3 or 4 digits) [ ]EXT (3 or 4 dqis) q EXT (3 or 4 dgils) [Type:No.) - - - - - - ORUT ONone IJRMT ONone q Dial Mode q DTMF 0Pulse q WMF q Pulse - - - RMT ONone q ~DTMF q Pulse q - - - RMT ONone q q DTMF Pulse - - - ORMT ONone q DTMF q Pulse q q IDTMF IJPulse q q DTUF lPulse q DTMF 0Pulse q w (10 WI q OHM (20 pps) OHM (20 PPS) q Pulse Speed q l.w(10 w) % Break 060% CPCDetection 06.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds :;5 mseconds 06.5 mseconds X -/msec. 08x-lmsec. 08x Imsec. 08x-Imsec. 08x-/msec. 08x-lmsec. 08x-lmsec. 08x-lmsec. 067% ONone DID start Arrangement q LOW (10 PPS) Thigh (20 IW) LOW (10 pps) LOW (10 pps) OHM (20 IFS) 060% 067% ONone q immediate Start q Obnd Delay Wink q ONone immediate Start IJlmmediate Start Send Delay Wink q Send Delay Wink nNone q q nNone Co: Ext. No with ATLC: blank C O t-xl N o l--T---ne ,--T--None GRMT--None- 080 mseconds 080 mseconds 080 mseconds 080 mseconds 060 mseconds 060 mseconds DTMF 080 mseconds 080 mseconds Duration Time 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds Thigh (20 pps) co: 01 DlD: l6 IJLOW (1Opps) q High (20 pps) OLOW (10 pps) IJLOW (10 pps) OHigh (20 pps) q High (20 pps) q 60% 060% 060% 067% 067% n67% nNone rlNono nNonn llmmediate Start q immediate Start Olmmediate Start IJlmmediate Starl q immediate Start Sand Delay Wink USend Delay Wink USend Delay Wink USend Delay Wink USend Delay Wink DTMF 80 - 50 (400ms) Send Delay Wink TRUNK-CO LINE Trunk Equipment Number Default Value Item Trunk Group - - (2 digiis: 01 lo 16) Trunk Name - (2 digits: 01 lo 16) - - - (2 digits: 01 lo 16) (2digils: 01 - . _ . ___. IO 16) - - - - - - _ _ _ _ - - _ _ c - -_- - _. __. -------__-----____--- Direct Termination - Dial DN (3 or 4 digits) ONone - - ODN (3 or 4 digits) q ONone ONone - --A- tviqde A-_- - - q DN (3 or 4 digits) nNone - ,~ _.__...... - - . - - - DN (3 or 4 digits) nNone - - -_- Pulse Speed __-- - - - - - - - ORMT ONone q RMTONone q RMTnNone nRMT nNone q q q q q DTMF q q DTMF q q DTMF IJPulse CILOW (10 Pf.4 q HishPJ pps) DTMF Pulse Pulse - - q - - - DN (3 or 4 digits) - q co, 01 DID: ’ 6 1 xxxx Phyxll _ _ _ _ -__-_-Number _ _ _ _ _ DN (3 or 4 digits) q ]DN (3 or 4 digits) Co: Ext, No, --_- -___ _ flNone nNone nNone - - with ATLC. blank Pulse CO: Ext. No. --_- _ _ _ _ ___nRMT nNone nRMT nNone nRMT [INone ______~ _.__- -___-..-... DTMF ODTMF PlJlse LIPulse 080 mseconds 0160 mseconds 080 mseconds q 164l mseconds 080 mseconds q lsO mseconds 080 mseconds 0160 mseconds 080 mseconds OLOW (10 pps) IJLOW (1Opps) aHigh (20 pps) OLOW (IOpps) OHigh (20 pps) q q q q 060% 060% oHi@ (20 pp) % Bregk CPCDeteC~iOn - ORMT ONone 080 mseconds DTMF Duration Time 0160 mseconds DID start Arrangement q DN (3 or 4 digits) _. (2 digits: 01 lo 16) (2 digits: 01 to 16) OLINAl, q uNA2 OUNAI, OUNA2 OUNAI, OUNA;! OUNAI, q UNAZ OUNAI, C-Iu~A2 F 1uN~i. I IUNAZ I luN~i. I IUNA~ I IUNAI, I IUNA~ q EXT (3 or 4 digits) OEXT (3 or 4 digits) q EXT (3 or 4 digils) q EXT (3 or 4 digils) OEXT (3 or 4 digils) UEXT (3 or 4 dlgils) UEXT (3 or 4 drgrts) UtXT (3 or 4 dIgIts) Fii: Answer (Type:No.) q (2 digits: 01 lo 16) (2digits: 01 to 16) 067% - ..- ----.-- -. LOW (10 pps) High (20 pps) 067% q ONone ONone immediateSlarl Olmmediate Start DImmediate Start bnd De@ Wink OSend Delay Wink OSend Delay Wink ONone q q ONone ~DTMF UPulse 080 mseconds 080 mseconds 0160 mseconds 0160 mseconds 0160 msecunds LOW(1Opps) High (20 pps) 060% 067% 06.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds Lj6.5 mseconds 08x /msec. 08x-lmsec. 08x-lmsec. 08x-lmsec. 08x-lmsec. U8x-lmsec. ONone ~DTMF UPulse ONone DTMF 8o q ILOW(10PPS) OHigh (20 pps) CILOW (10 PP) OHigh (20 pps) _ 060% 067% 060% 067% - i- ii5 mseconds X lmsec. lm.16.S ONone ONone Illskxolds lm18x ~~~ lmsec 50 (4OOms) Send Delay immediateStall q immediateStart nlmmediale Start rllmmediate Slarl nlmmediale Start Wink Send Delay Wink aSend Delay Wink USend Delay Wink USend -Delay Wmk - USend- Delay- Wmk I - TRUNK420 LINE Trunk Equipment Number item Trunk Group TrunkName - (2digits: 01 lo 16) (2 digits: 01 lo 16) (2 digits: 01 lo 16) (2 digits: 01 lo 16) - - - _ q _ _ _ _ _ DN (3 or 4 digiis) q _ - - ---_--___-_- DN (3 or 4 digils) q DN (3 or 4 digits) q DN (3 or 4 digits) -v-w _-__ ___- _ _ q IRMT ONone q RMT ONone IZ]RMT ONone q q DTMF Pulse q q DTMF lPuise q DTMF q Pulse q _ RMTONone _ URMT ONone _ q _ _ _ DN (3 or 4 digits) _ ODN (3 or 4 digits) ODN (3 or 4 dtgils) - - _ - Co: Fx,, No, _ _ -. -~~ q q DTMF Pulse ODTMF q Pulse _-__ ___-q RMT UNone KIDTMF UPulse 080 mseconds DTMF 080 mseconds 080 mseconds 060 mseconds 080 mseconds Duration Time 0160mseconds 0160mseconds 0160 mseconds 0160mseconds 0160 mseconds q LOW (10 PM q LOW (10 Pps) q ILOW(10 w) q OHi@ (20 wl Thigh (20 PI-N aHigh (20 pps) LOW (10 pps) C]High (20 PPS) OLOW (1Opps) aHigh (20 pps) % Break 060% 067% 060% 06Q% Lb% 067% 067% 067% u60% 067% 067% 06.6 mseconds 08 x -/msec. ONone 06.5 mseconds 08 x -/msec. ONone OS.5 mseconds 0 8 x -/msec. UNone 06.5 mseconds 08 x _ _/msec. ONone u6.5 mseconds fl8 x .._ Imsec. IdNone 06.5 mseconds CPC Detection 08 x - /msec. ONone q immediate Start Olmmediate Starl q immediate Start USend Delay Wink OSend Delay Wink USend Oelay Wink q q i IDTMF I IPulse 1 DTMf ___-.- -.---. .-.---- 060 mseconds 0160 mseconds Pulse Speed DID start Txxxx physical Number --_- - - - -. _- -.- .-- O&Al, OUNA2 q uNAi, C3M2 OUNA~, Ours q UNAI, q uNA2 q UNAI, OuNA2 q luN~i,CIUNA~ q EXT (3 or 4 digits) IJEXT (3 or4 digiis) q EXT (3 or 4 digits) [7EXT (3 or 4 digits) q EXT (3 or 4 digits) OEXT (3 or 4 digits) Dial Mode Arrangement (2 digils: 01 lo 16) -_.- - _ ---_-__-___ --__ - - -ONone ONone ONone ONone ONone ONone F’@$ Answer 6 - ODN (3 or 4 digits) Direct Termination (Type:No.) (2 digits: 01 lo 16) -~~-------------~~~~-~-~~~_~_~~__~~_~_~_ - T s (2digits: 01 lo 16) D80 mseconds D 160 mseconds OLOW (10 pps) ULOW (10 pps) q liigh (20 pps) nHigh (20 PPS) -~--____--_ ~~_____ I .lw% f’-1;5 mseconds x ~/msec 1 INone immediate StarI Olmmediate Stati q llmmediale Start UImmedate Start Send Delay Wink USend Delay Wink USend Delay Wmk aSend Delay Wink 080 mseconds iJ 160 mseconds 80 !zlLow (10 PPS) q tiigh (20 pps) _ - - j TRUNK’CO LINE Trunk Equipment Number Default Value Item Trunk Group - (2 digits: 01 to 16) TrunkName - - - - - (2 digits: 01 lo 16) (2 diiz Olto 16) - - - - - - (2 digirs: 01 lo 16) q - - q RMTONone _ q _ _ RMT ONone q q DTMF Pulse q q DTMF Pulse DTMF q KIO mseconds Duration Time 0160 mseconds Pulse Speed CpcDetec~~~ DID start Arrangement q DN (3 or 4 digits) DN (3 or 4 digits) q - - DN (3 or 4 digils) - - q - - - DN (3 or 4 digils) - - q - _ _ DN (3 or 4 digits) _ _ _ _ _ co: 01 DID: ’ 6 (2 digits: 01 to 16) _ _ _ _ L _ _ _ _ UDN (3 or 4 digits) _ _ nDN (3 or 4 digits) _ _ Txxxx physical Number co: Ex,. No, _ _ _ _ ““~,,A,Tklc’ ONone q UNAl, q lUNA2 q IUNAI, q UNM Out-M, •UNA~ q UNAI, q uNA2 q UNAI,lJu~~2 DNAi, •UNA~ q UNAI,UUNA~ q UNAI,OUIJA2 q EXT (3 or 4 digits) q EXT (3 or 4 digiis) q EXT (3 or 4 digits) q EXT (3 or 4 digits) IJEXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digils) q EXT (3 or 4 digils) Dial Mode % Break q (2 digits: 01 lo 16) - - - _ _ _ _ _ _ _ _ _ - - - - - _ _ _ _ _ _ _ _ IJNone IJNone ONone ONone ONone aNone ONone Fzi: Answer (Type:No.) DN (3 or 4 digits) (2 digits: 01 lo 16) -_--___________ ----_-- -----P-----m-----Direct Termination (2 digils: 01 lo 16) _ q ___- RMT ONone q RMT ONone q DTMF q Pulse q q DTMF Pulse - q q q RMTONone DTMF lPulse - q q q --__ _ _ q RMTONone RMT ONone IDTMF Pulse q q DTMF Pulse _ q CO: Ext. No. _ _ _ RMT ONone q !DTMF 0 Pulse 080 mseazmds 0160 mseconds 080 mseconds OS0 mseamds 080 mseconds 080 mseconds 080 mseconds 080 mseconds 0160 mseconds lJl60 mseconds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds Of-W (20 FM q L~(lOpPs) q High (20 pps) Oh (low) OHM (20 ppsl OLOW UOPPS) OHigh (M FP) CJLOW (1Opps) q High (20 pps) IJLOW (1Opps) q High (20pps) E%I Ei EF Oo 060% 067% 060% 067% 060% 067% q LOW (10 PPq q q LOW (10 pps) High (20 pps) EC Oo q LOW (10 pps) OHigh (20 pps) mo% 067% 06.5 mseconds 06.5 msewnds 06.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 msaconds 06.5 mseconds 06.5 mseconds 08x-Imsec. 08x-lmsec. 08x-lmsec. 08x-/msec. 08x-lmsec. 08x-/msec. q 8x-/msec. q 8x-/msec ONone ONone ONone ONone ONone ONone ONone ONone q immediate Start q immediate Start USand Delay Wink usend D&y Wink q q immediate Start q immediate Start DImmediate Start Send Delay Wink USend Delay Wink aSend Delay Wink q lmmedia~eStart IJImmediale Starl DImmediate Start USend Delay Wink aSend Delay Wink USend Delay Wink DTMF 80 - (405ooms) Send Delay Wink TRUNK;CO LINE Trunk Equipment Number Default Value Item TrunkGroup (2 digiis: 01 to 16) (2 digiis: 01 to 16) Trunk Name (2 digiis: 01 to 16) (2 digits: 01 to 16) (2 digits: 01 to 16) (2 digits: 01 to 16) (2 digits: 01 to 16) - - - _ _ _ - - - _ _ - - _ - _ _ _ _ _ _ - - _ _ _ _ - - - -.. - - - - - - - _ _ - _ _ ~_~ -A------_---------_------__-_-- q Direct Termination q DN (3 or 4 digiis) DN (3 or 4 digits) - - - -1. - - ONone ONone q DN (3 or 4 digits) - - - ONone nUNAl, q UNA2 OUNAI, q luNA2 •UNA~, q UNA2 q IEXT (3 or 4 digb) q EXT (3 or4 digits) IJEXT (3 or 4 digits) Fjt$ Answer (Type:No.) -m-m q RMT ONone Dial Mode q q - DTMF Pulse DTMF 080 mseconds Duration Time 0160 mseconds DN (3 or 4 digits) - - _ ONone q DN (3 or 4 digits) _ _ _ _ ONone q DN (3 or 4 digits) _ _. _ _ ONone q UNAI,lJuNA2 q UNAI,q ~NA~ q luN~i, •UNA~ q UNAI,•UNA~ q EXT (3 or 4 digits) T’JEXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) 080 mseconds 0160 mseconds 080 mseconds 080 mseconds 080 mseconds 080 mseccnds 080 mseconds 080 mseconds 0160 m s e c o n d s 0160 m s e c o n d s 0160 msaconds 0160 m s e c o n d s ml66 m s e c o n d s 0160 mseccnds DTMF Pulse q q DTMF Pulse OLOW (1Opps) q High (20 pps) LILOW (10 pps) aHigh (20 PI@ LOW (1Opps) OHigh (20 pps) 060% 067% 060% 067% Ez 060% 067% 060% 067% 060% 067% 067% q q q q q 060% ONone DTMF OPulse LOW(1Opps) O H @ (20 pps) % Break 06.5 mseconds q q _ _ RMT ONone q 04th (20 pps) immediate Start Send Delay Wink uNAl, CM2 EXT (3 or 4 digits) - _ _ ONone q ODTMF IJ Pulse DTMF IJPulse OHi@ (20 pp4 q q q q DN (3 or 4 digits) q OLOW (l0f.w q - - - ONone q q DTMF OPulse q LOW (10 FM 06.5 mseconds 08x-Imsec. ONone DN (3 or 4 digits) _ q LOW (10 PI4 CPCDetection q __,______- -_-- -_-- -__- --_- _ _ q RMTONone q RMT ONone q RMT ONone q RMTONone q RMTONone Pulse Speed DID start Arrangement (2 digits: 01 to 16) 06.5 mseconds 06.5 mseconds 06.5 mseconds ]8x-lmsec. 08x-lmsec. 08x-lmsec. 08x-lmsec. ONone ONone ONone lmmediite Start IJlmmediate Start q immediate Start Send D&y Wink q Send Delay Wink OSend Delay Wink q q 06.5 mseconds 08x-lmsec. ONone q High (20 pps) _ q co: 01 DID: 16 Txxxx phys,cn, Nul:lbur Co: Ext. No, with ATLC: blank CO: Ext. No. _ _ RMT 0 None q IDTMF 0 Pulse DTMF 8o t-bw (10 PP) q High (20 pps) _ 060% 067% - 06.5 mseconds 06.5 mseconds 08x-/msec. q ]8x-/msec. (405ooms) ClNone ONone immediate Stan q immediate Start q immediate Stan q immediate Start Send Delay Wink USend Delay Wink USend Delay Wink USend Delay Wink TRUNK-CO LINE T Trunk Equipment Number Default Value ~_ Item Trunk Group Trunk Name -(2 digits: 01 lo 16) -(2 digits: 01 lo 16) (2 digits: 01 lo 16) (2 digilk: 01 IO 16) (2 diglts: 01 to 16) (2 diglls 01 IO 16) dKys 01 IO 16) -_____(2 ---~~__----------------------- - - - - (2 d&y:; 01 10 I(i) rxxxx - Physlcal Number -_---_------_------Direct Termination Night Answer Point [Type: No.) q DN (3 or 4 digits) - ONone - - q JW q W2 OEXT (3 or 4 digits) q DN (3 or 4 digits) - ONone q q - - IUNAI, •UNA~ IEXT (3 or 4 digits) q DN (3 or 4 digits) _ _ ONone q q _ q q DTMF Duration Time 080 mseccnds 0160 mseconds 080 mseccnds 0160 mseconds 080 mseconds 0160 mseconds Pulse Speed ElLow (10 pps) OH&h (20 PPS) q q q q f/o Break Detection DID start Arrangement q q DTMF lPulse LOW (10 pps) High (20 pps) cl60% n67% ::5 mseconds X _ /msec. ONone 51685 msecends X -/msec. ONone q q q immediate Start USend Delay Wink q q ---- _ _ ONone ---- ---- ---q IRMT ONone I ORMT IJ None ORMT ONone DTMF Pulse q DN (3 or 4 digits) _ DTMF Puls.e LOW(1Opps) High (20 pps) _ lJ60% n67% 06.5 mseconds 08x Imsec. ONone q q q - - - RMT ONone DTMF lPulse 060% [-1670/o 06.5 mseconds 0 8 x _ /msec. ONone q q _ RMTONone IDTMF Pulse - DN (3 or 4 digits) - - - q UNAi, q uNA2 q lUNAi,•UNA~ q ]EXT (3 or 4 digits) nEXT (3 or 4 dtgss) - - - q RMTONone q q q CDTMF q lPulse DTMF Pulse - q q q q cl60% 1767% nSO% I 167% C60% I 167% L30% I Icx 06.5 mseconds Imsec. 06.5 mseconds 0 8 x _ imsec ONone :;5 mseconds X _ Imsec. ONone 06 5 mseconds 0 8 x _ Imsec. ILOW(1Opps) High (20 pps) 0 160 mseconds LOW (10 p@) High (20 pps) 30: Ext. No Nith ATLC: blank 20: Ext. No. RMT ONone LOW (10 pps) OHigh (20 pps) q - ONone US0 mseconds 0166 mseconds LOW(1Opps) High (20 pps) q _ - q US0 mseconds 0160 mseconds 080 mseconds q q DN (3 or 4 digits) ONone lUNAl,IJUNA~ OUNAl, •UNA~ •UNA~, q luN~2 q lUNAl,•UNA~ EXT (3 or 4 digits) q JEXT (3 or 4 digits: q EXT (3 or 4 digits) TJEXT (3 or 4 digits: Dial Mode CPC _ q ~0~01 111) l(i US0 mseconds 0 160 mseconds DTMF 80 IJLoa (10 pps) q High (20 pps) ONone immediateStart Olmmediate Start q immediate Starl q immediateStart q immediate Stan nlmmediale Slarl Ll]lmmedlale Start Send Delay Wink q Send Delay Wink USend Delay Wink USend Delay Wink USend Delay Wink USend Delay Wink USend Delay Wmk 50 (400ms) Send Delay Wink a"oN/-J (SWOOP) OS au0Nr-J e'J0Nf-J au0Nr-J e'J0Ni-J e"oNO WU/-X80 '3aSU/-X8~ 3aSUJ/-X80 '33SW/--X80 33SUJ--X80 *%IJ(--Xf3~ spuo3wll r;‘go spuo3wLl g.90 spuo3esul ygn spu~esul g.90 sPu~sws:9Q spumeslu g’go euONO euONO 3WlJ/--X~~ '30esW/ - x splmesw qgo 8 Cl spuo3esul qgo - %L9U %09 0 %L9U %09(-J %19rJ %09(-J %190 %09~ XL90 oM9/-J %190 %wl %L90 %L90 OMO - (SdOZ) 46!Ho (Sd 01) MolO (sd OZ) '$!Ho (SM 01) Mq--J Woz) @!HrJ (scfdoz) @!HO (SdOZ) @!Hn id OZ) 4[kHO (M oz) q6!Ho (d OZ) ‘@!Hc] (~01)wO W"dLJ jwlau W"dU jwlau WOl)WO (s~OL)MfJln (S~OI)W~ “m0 (~Ol)W~ WOl)MqJ uo!lwea 3d:: P&S em 08 jvua _ ON .IX3 :03 - a"ONn lWH0 - a"ONO nUti auONu lWtr0 e"ONO lWtl0 --__ __-- - - - - a”ON 0 - (v~!P P 10 E) Nag - - - - - - - - S’JON 0 - - - - a”oNO - b1!6!p P 10 E) NaC] W!P P JO c) Nag - - - - - - - - - - ~l!“15A’~c~ - - - +“J”No - (s!@P PJO E) two - - (91 01-ln.ss6fP -.I' ZF (91 01-Lo:s1!6!P - I) (91 01-LO :SV~~P 1' z) - - eu"NO lWtl0 - - W!P PJO E) Nan - - - - - - - - - (91 oi-lo :s116tp 1' Z) euONO _ - - - xXxX1 91 :aia epow - euoN0 lWk40 - - euoN0 - - ~!BP P '0 E) 1x30 W!P P JO c) lx3lJ W!P PJOC) 1x3l-J (s!~!P PJ'J EI 1x30 (V?PPJ~ CI 1x30 W!PP JOE) 1X30 k@!PtJoC) 1X30 h!QP tJOE)lX30 ZVNfln ‘1VNnu ZVNnu ‘1VNfIu ZVNrln ‘1VNflf-J ZVNnO ‘IVNf’lO ZVNnn ‘IVNfIO ZVNtll-J ‘1VNnO ZVNflu ‘1VNnO ZVNflO ‘1VNMnO wq :311V 41!M ON.'lx3 :03 JaCjUJflN auONO 1WHu - ==l"dO ma0 f”JoNO - - W!P P 10 E) NaO __----- - - - - _----.-. (91 ok_10 :s1161p 1' 2) 3NIlO3-YNntrl - - - - - - @JON0 - W!P PJO E) NaO - - -euoN0 - W!P~JOE) r4ai-J lWtr[7 ('ON JWbWJ~ ie!c :edAl lU!O, 1q6y uo!ieu!wle~ W’!C _---------- (9101-A' 10 :SU~IP I) - --------i-- (9101 -L.' LO:SII~~PZI (9101 -IO:S@!PZ) - eurefqyunjJ dnoq))unlj TRUNK--CO LINE 8 Trunk Equipment Number Default Value Item Trunk Group (2 digits: 01 lo 16) - (2 digits: 01 lo 16) TrunkName --v---e - (2 digits: 01 lo 16) - - - (2 digits: 01 to 16) (2 digits: 01 to 16) - - (2 digits: 01 10 16) - ------------------------_-- ------------------------------_ Direct Termination - - IJNone - - - q DN (3 or 4 digits) ONone q luw OuNA2 q q EXT (3 or 4 digits) q Fii: Answer (Type:No.) q ODN (3 or 4 digits) - _ _ ONone UNAI,•UNA~ EXT (3 or4 digits) q DTMF (JPulse q _ Oh (10 I?) % Break kE700 q H@ (20 pps) _ _ ONone - q q DTMF :::lr q q LOW (10 PPS) OHM (20 pps) 060% 067% q DN (3 or 4 digits) _ _ DN (3 or 4 digits) _ ONone q DN (3 or 4 digits) q - _ _ - - DN (3 or 4 digits) ___- __-- - ONone - ONone - (2 digits: 01 lo 16) - _ _ - - _ - - ODN (3 or 4 digits) - ONone --_- RMTONong q RMT ONone DTMF nputse - q - RMT ONone _ q q DTMF DTMF IlPulse IIlPulse _ q _ RMTONone q DTMF flPulse _ q q LOW (10 pP4 q High(20 pps) :z :zOo q LOW(1Opps) q HM (20pps) 060% 067% q q LOW (10 pps) High (20 pps) 512 Oo q ODTMF n Pulse cl60% - 067% 067% 08x-lmsec. ONone DID start Arrangement q immediate SlatI Olmmediate Start USend Delay Wink USend Delay Wink Olmmediate Start q lmmediare Start Gelay Wink aSend Delay Wink a’ q o% 06.5 mseconds q DTMF - 08x-/msec. ONone immediate Slart CO: Ext. No. LOW (10 pps) Thigh (20 w) 06.5 mseconds Send Delay Wink USend blank q 06.5 mseconds 08x-Imsec. ONone q Co: Eti. No, ILOW (10 pps) aHigh (20 pps) 0 6 . 5 m s e c o n d s OS.5 m s e c o n d s 0 6 . 5 msecwds 06.5 m s e c o n d s 06.5 m s e c o n d s 08x-Imsec. 08x-/msec. 08x-Imsec. 08x-lmsec. 08x-/msec. ONone ONone ONone ONone ONone immediate Start Delay Wink q Number RMTUNone CPCDetection q OS& Txxxx ,,hyslca, with ATLC: --_- 080 msewnds 080 mseconds 080 mseconds 080 mseconds 080 mseconds 080 mseconds 16Omseconds 0160 mseconds ~160 mseconds 0160 mseconds 0160 mseconds al& mseconds q ILOW(10 pps) q Hish (20w) DID: 1 6 _ q UNAI,•UNA~ q uNAi,•UNA~ q uNAl,•UNA~ q luNAl, •UNA~ q luNAl.•UNA~ q lu~~i, •UNA~ q EXT (3 or 4 digits) q EXT (3 or 4 digils) q EXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digfls) IJPulse DTMF 080 mseconds 080 mseconds Duration Time 0160 mseconds 0160 mseconds Pulse Speed q DN (3 or 4 digits) ____’ _--- -__- IJRMT ONone q RMTONone ORMT ONone Dial Mode co: 01 - (2 digits: 01 lo 16) immediate Start nlmmediale Slarl USend Delay Wink. USend Delay Wink (40%x) Send Delay Wink TRUNK&CO LINE Trunk Equipment Number Default Value Item (2 digits: 01 to 16) Trunk Group TrunkName (2 digils: 01 lo 16) (2 digits: 01 lo 16) (2 digits: 01 lo 16) (2 digits: 01 to 16) (2 digits: 01 lo 16) (2 digits: 01 to 16) ---------~~~~~~~~~~~~~~~ ~~----------____ - q Direct Termination - - - - - - DN (3 or 4 digils) ONone - - - q - - - - q DN (3 or 4 digits) - - - ONone - - - - - - - q -]DN (3 or 4 digits) - - - ONone - - q - - - DN (3 or 4 digits) - - - None - q - - - - DN (3 or 4 digits) nNone - - - - q - - - DN (3 or 4 digits) --__ _ nNone - - q - - - DN (3 or 4 digits) _ _ _ nNone - - - - - q DN (3 or 4 digits) _ _ _ nNone Dial Mode Txxxx Physical Number Co: Ext, No, _ with ATLC: blank q q uNAi, ODTMF q lPulse q DTMF IJPulse ~DTMF q Pulse C~DTMF q Pulse IXITMF 0Puls.e ~DTMF UPulse nDTMF UPulse ~DTMF UPulse 080 mseconds 080 mseconds DTMF 080 mseconds 080 mseconds 080 mseconds 080 mseconds 080 mseconds 080 mseconds Duration Time 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds Pulse Speed % Break co: 01 DtD: I6 q uNA2 q uNAi, •UNA~ q lUNAl,•UNA~ q UNAI, q luNA2 q uNAi, CM2 q IUNAI,q ~NA~ q UNAI,•UNA~ q lUNAi,•UNA~ EXT (3 or 4 digits) IJEXT (3 or 4 digits) IJEXT (3 or 4 digits) q IEXT (3 or 4 digils) q EXT (3 or 4 digils) q EXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) CO: Ext. No. _--- -_-_ ---_ -----. q R M T ONone ORMT ONone ORMT ONone ORMT ONone OHM1 UNorw [_]lIMI I INow I l;Ml I INow ( IIiMl I ~~~~~~~~ Fzi: Answer (Typ:.Jo.) (2 digiis: 01 to 16) q LOW (10 Pf.M OH@ (20pps) 060% 067% Oh (10 pps) q Hish(20 pps) q LOW(1Opps) Thigh (20 pps) 53K EE Oo q LOW(1Opps) OHi@ (20 PM 060% 067% q q LOW(1Opps) High (20 pps) ETOo q q LOW(1Opps) High (20 pps) 060% 067% q LOW (10 pps) q HM (20ppsl q LOW (10 PIN q High (20 pps) 060% q W% 067% 067% DTMF a’ _ - 06.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds 06,s mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds 50 CPCDe~ec~ion 08x-/msec. 08x-lmsec. 08x-lmsec. 08x-lmsec. 0 8 x Imsec. 08x-lmsec. 08x-/msec. 08x-lmsec. (400ms) ONone ONone ONone ONone ONone ONone ONone ONone DID start Arrangement q q immediateStart q immediate Start DImmediate Slatl Olmmediate Start Send Delay Wink OSend Delay Wink q Send Delay Wink OSend Delay Wink q immediate Start aImmediate Stari q ]Immediate Start USend Delay Wink aSend Delay Wink USend Delay Wink IJImmediale Starl q Send Delay Wink Send Delay Wink TRUNKtiC LINE Trunk Equipment Number Default Value Item Trunk Group Trunk Name Iirect rermination !z,“: ~WW ‘Type: No.) Iial Mode - - (2 digils: 01 lo 16) -_. ._.-. (2 digits: 01 lo 16) (2 digils: 01 lo 16) (2 digits: 01 lo 16) (2 digits: 01 lo 16) (2 digils: 01 lo 16) (2digilsOllo16) Txxxx q IDN (3 0r 4 digits) q i&r- - DN (3 of 4 digits) q DN (3 or 4 digits) q DN (3 or 4 digits) q DN (3 or 4 digits) q DN (3 or 4 digits) q - cluNA1,cluNA2 q q EXT (3 or 4 dig&) q DTMF IJPulse None None q q DTMF Pulse - q ---_--__-____ RMT ONone q DTMF IJPulse q LOW (10 PP4 q High (20 PM q LOW (10 pps) q Hish(20 PPS) ‘/o Break 060% 060% 067% 067% Arrangement q q q RMT ONone DTMF Pulse q q q RMTONone IDTMF lPulse q LOW (10 WI aHigh (20 pps) EiE O.2 q ONone ONone q _ _ - _ RMTONone q DTMF IJPulse LOW(1Opps) OHigh (20 pps) q 060% 060% 067% US.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds 08 x -Imsec. 0 8 x /msec. 0 8 x /msec. 08 x -/msec. 08 x -/msec. ONone ONone ONone q q q q q immediateStan USend Delay Wink DN (3 or 4 digits) - - q immediate Slarl Sertd Delay Wink ONone C]None q RMTIJNcne q q Pulse IDTMF ILOW(1Opps) - CO: Ext. No. - with ATLC: blank lu~Ai,•UNA~ EXT (3 or 4 digils) CO: Ext. No. - q ___RMTONone q q DTMF Pulse 0160 mseccnds 080 mseccnds 0160 mseconds q LOW (10 pps) IJLOW (10 pps) OHigh (20 pps) High (20 pps) 080 mseconds aHigh (20 pps) DN (3 or 4 digits) ONone , IuNA~ q IUNAI , •UNA~ q UNAi •UNA~ , q UNAi, q luNA2 q DUNAt, q UNA;! q lUNAi , •UNA~ q lDNAi q q EXT (3 or 4 digiis) q EXT (3 or 4 digils) TJEXT (3 or 4 digits) IJEXT (3 or 4 digits) IJEXT (3 or 4 digits 1 q IEXT (3 or 4 digils) q -GT-ONone ORMT ONone q None CjNone Use Speed DID start co. 01 DID. I6 (2diglls:Oltol6) - .---------- - - - - __----------------------Physical Number _------------------------. -----_---I----- 080 mseconds 080 mseccnds 080 mseconds 080 mseccnds 080 mseccnds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds PC Detection 1 q DTMF 80 067% 06.5 mseconds 0 8 x _ Imsec. ONone immediateStan q llmmediale Stan q immediateStan IJlmmediale Sian Send Delay Wink OSend Delay Wink aSend Delay Wink USend Delay Wink 50 (400ms) - Send Delay Wink TRUNK-CO LINE Trunk Equipment Number Default Value - Item (2 digits: 01 lo 16) Trunk Group rrunkName rit: Answer - - - q LIN (3 or 4 digits) ONone q q - (2 digits: 01 to 16) (2 digits: 01 lo 16) - - UNAI, q luw2 EXT (3 or 4 digits) q q DTMF Pulse q q DN (3 or 4 digits) ONone - - DN (3 or 4 digits) ONone - q DN (3 or 4 digits) ONone - - q q DN (3 or 4 digils) ONone - (2 digits: 01 to 16) - DN (3 or 4 digits) ONone - ODN (3 or 4 digils) C]DN - ONone - - q RMTONone q D~MF q PUlSe - q RMTONone q q DTMF Pulse --_- q RMT ONone q DTMF IJPulse ORMT ONone q q --__ _ q RMT ONone DTMF Pulse q Y0 Break 060% i60% 067% PC Detection 06.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds 06.5 mseconds 0 8 x _ Imsec. 0 8 x _ /mm. 0 8 x _ Imsec. 0 8 x _ /msec. 08x I m s ONone ONone ONone ONone ONone DID start Arrangement q q 067% LOW(IOpps) OHigh (20 pps) q LOW(1Opp) q q q Low (10 pas) Thigh POpps) ---- DID: ‘6 Txxxx Physical --_-with ATLC: blank ONone - ODTMF OPulse _ q _ _ RMTONone q q DTMF Pulse _ OHM (20 pps) q LOW (1Opps) High (20 pps) 060% EEOo 067% LOW (10 pps) OHM (20 pps) OLow (10 P M OHigh (20 pps) 060% 067% Ez e use ET:’ DTMF 80 OLow (10 P) C]High (20 pps) - 060% 060% 067% 067% - 06.5 mseconds 06.5 mseconds 06.5 mseconds c . 08x-lmsec. 08x-lmsec. /$x-/msec. ONone ONone one immediate &tart Olmmediate Start q immediate Slarl q immediate Start q lmhlediate Start Cjlmmediate Start Send Delay Wink q Send Delay Wink OSend delay Wink USend Delay Wink OSend Delay Wink USend Delay Wink CO: Ext. No. _ _ _ ORMT ONone 080 mseconds. 080 mseconds 060 mseconds 080 m-seconds 080 mseconds 080 mseconds 080 mseconds 080 mseconds Time 0160 mseconds 0160 mseconds 0160 mseconds 0160 mseconds lJl60 mseconds 0160 mseconds 0160 mseconds 0160 mseconds Speed co: 01 (3 or 4 digits) CO: Ext. No. q uNA~,OuNA2 q lu~Ai, q lu~~2 OuNAi, •UNA~ q uNAi, OuNA2 OuNAi, •UNA~ q UNAI,OUNA~ OUNAI. OUNA~ q EXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) q EXT (3 or 4 digits) OEXT (3 or 4 digits) [7EXT (3 or 4 digils) q EXT (3 or 4 digiis) q LOW (10 PF4 q High (20 pps) Pulse (2 digits: 01 to 16) (2 digits: 01 to 16) ___- --_--_--_-------------_-----_--Number - _--_ q RMT ONone 3ial Mode 3TMF &ration (2 digits: 01 lo 16) ----------------------~--~~------------~ 3irect Termination - :Type:NoJ (2 digits: 01 lo 16) q q llmmediate Start IJlmmediate Start Send Delay Wink DSend Delay Wink (405d)ms) TRUNK-PAGER & MUSIC SOURCE Tenant Item Set Data oveaf~$ 1 0’ 1 BGM Set Data “v”,‘rJt Set Data y!T$ Ecs No 0 02 External Tone 0 Yes No 0 No Pager 2 0’ 1 Set Data ~~~~t Set Data vjy$ 1 cl2 2 Cl1 cl2 1 c] Hold Hold 8 0 BGM BGM 0 Hold & BGM 1 r External pager -S Music source 1 S-19 0 Yes 0 No For User Note: Press TAB j No Tenant 01 Music Source 0 Yes 0 No El2 f-J Hold 0 BGM j-J Hold & BGM Hold & BGM No TRUNK-CO LINE Trunk Equipment Number Item t -(2 digils: 01 to 16) _ _ - - - - - - - -(2 digils: 01 lo 16) - q - - ONone (Type: No.) OUNAi, q uM2 q q EXT (3014 digits] q q - - - RMTONone Dial Mode q q DTMF Duration Time 080 mseconds 0160 mseconds Pulse Speed q IL~ (10 pps) OHish (20 FIN DTMF PuIse % Break - - 06.5 mseconds 08 x _ /msec ONone DID start Arrangement q q - - _ q DN (3 or 4 digits) - - - - ONone - - - - q _ - _ _ ONone - - - - DN (3 or 4 digits) - q _ _ _ _ ONone - - - IJRMT ONone DTMF q RMT ONone ONone RMT ONone 080 mseconds 080 mseccnds 080 mseccnds 0160 mseconds 0160 mseconds 0160 mseconds q 080 mseconds 16g mseconds 080 msewnds q LW (10 Fw q H@ (20 pps) DTMF IJPulse q RMTONone ~DTMF Pulse DTMF IJPulse q LOW (10 pps) q LOW (10 PP4 q Thigh (20 FPS) q 060% 080% 060% q High (20 pps) 067% LOW(1Opps) High (20 pps) 067% - q - - - - - _ _ _ q 7DN (3 or 4 digits) q - - - Ncne - - RUTONone q 1.. ] Pulse ODTUF I .]Pdse 080 msecnnds 0160 mseconds 080 mseconds 0160 mseconds q LOW(1Opps) OH@ (20 pps) OLow (10 pps) OHi@ (20 PPS) GLOW (10 pps) aHigh (20 pps) 060% 060% 060% 0160 mseconds 067% 067% immediate Starl q immediate Start q immediate Stan q llmmediateStan (JImmediate Stan q immediate Stan q immediate Stan Send Delay Wink USend Delay Wink USend Belay Wink OSend Delay Wink USend Delay Wink OSend Delay Wink O.%nd Delay Wink with ATLC: blank CO: Ext. No DTMF 80 - 067% 06.5 mseconds q q CO: Ext. No. $iTO None ~DTMF 1JPulse - uNAi, nUNA q UNAI, q uNA2 ]EXT (3 or 4 digits) IJEXT (3 or 4 digits) - co: 01 DID: 16 Txxxx ONone q q -- (2 digits: 01 lo 16) - ----- Physical - -_---- Number DN (3 or 4 digits) --__ _ q DTMF q Pulse q q - DN (3 or 4 digits) __-- ---- q ---- q ---- q-q I RMT ONone (2 digits: 01 lo 16) __-----_-- UNAI,•UNA~ q luNAl,•UNA~ OUNAI, OuNA2 OuNAi, IJUNK q luNAi ,•IJNA~ lEXT (3 or 4 digits) C]EXT (3 or 4 digits) q EXT (3 or 4 digits) q ]EXT (3 or 4 digits)q EXT (3 or 4 digits) 067% CPC Detection - ~~~ [7DN (3 or 4 digits) BN (3 or 4 digits) - ~~~~ -(2 digits: 01 to 16) -(2 digirs: 01 lo 16) -(2digils: 01 lo 16) - ----e----m r ;k$ Answer Default Value /RISC%. 50 (400ms) immediate Start Send Delay Wink Send Delay Wink TRUNK-PAGER&MUSlCSOURCE Default Set Data Value Set Data 1 q ’ 1 Default Value [7 Yes No 0 No cl2 Edema+ BGM Tone Tenant Item Pager 2 0’ 1 EC= 02 Tenant For User Default Set Data “alue Set Data El1 Music Source 1 0 Hold 0. BGM 0 Hold 8 BGM Hold 8 BGM 1 0 Hold 0 BGM !--J Hold & BGM Hold 8 BGM l-II2 Note: Press TAB -----, ,-+ External pager w Music source1 1 Default Value 1 cl2 Cl1 2 No 0 I 5-19 TRUNK-AGC Set Data AGC Card Shelf Nc Slot No. Tenant 1 Ci, 32 2 Ill* 12 3 01s 32 4 01, 712 Default Value 1 5 Yes c No Tone Deter Note: Shelf No.-1 digit (1, 2 or 3) Slot No.-2 digits (01 to : 5) 5-20 Yes m x -, 0 3 EXTENSION-STATION Item Telephone Type 3 Selection of Value s- T SLG-SLT PLC-PITS HLC-P ITS OPX-oPX ?'A-T7020, KX-T7030. KX-T7050 KX-T123220, KX-T123230. KX-T123235 (7130) KX-T123250, KX-T30820. KX-T30830, F’CX-T30850, KX-T61620. KX-T6163C. KX-T61650 KX-T123235 (7130) F 7s CDX OHCA Circuit I I No Primary Directory Number Z 2’ 4-digit DN loo- i ntercom Number - zr 2 digits (0 to 99), or blank blank Station Name ‘+‘.’ :lin lo-digit alphanumeric characters blank * c’git (1 to 8) 1 2 cigits (01 to 32), or None None Next Hunt Station 3 or 4digit DN, or None None Class of Service 2 t,gits (01 to 32) 01: for DN 100 02: for DN except DN * 3r) Data Line Security YasjNo No Automatic Callback-Trunk Yas/No Yes Parallel Connect Yes/No No Key Type PDN, SDN, PRV-CO. OHCA MW, LOGIN, ALARM, SINGLE CO, GROUP CO, DSS(DN), DSS (IX), ONE TOUCH, PRV-CHG, EXT FEAT, CALL PAR. CALL STA, RNG TRAN, SPLIT. TONE-BRK, or blank PDN for DN-01 blank for the others Number 3 or 4 digits: directory number for “PDN”. “SDN”, “DSS (ON)” 1311 to 3158: physical number for “PRV-CO”, *Single CO” 1 or 2 digits: intercom number for “DSS (ICM)’ Ci to 16: trunk group number for “Group CO” maximum 16 digits: destination number for “ONE TOUCH” blank SDN COS STation: using COS of own extension DN: using COS of PDN blank Day Ring No ring instantly Delayed. 1 Delayed 3 Delayed 6 blank rI Default Value (conflwed) 6-1 item Default Value Selection of Value Night Ring No ring Instantly Delayed 1 Delayed 3 Delayed 6 b’ank PF Key Type DSS (ICM), ONE TOUCH, EXT FEAT, CALL PAR, CALL STA, RGN TRAN, SPLIT, FWD/DND, TONE-BRK, SNR or blank b:ank PF Key Number maximum 16 digits: destination number for “ONE TOUCH” 1 or 2 digits: intercom number for “DSS (ICM)‘ b’ank DSS Key Type b:ank MW, LOGIN, ALARM, DSS (DN), DSS (ICM), ONE TOUCH, PRV-CHG. EXT FEAT, CALL PAR, CALL STA, RNG TRAN. SPLIT, TONE-BRK, or blank DSS Key Number 3 or 4 digits: directory number for ‘DSS (DN)’ 1 or 2 digits: intercom number for ‘DSS (ICM)” maximum 16 digits: destination number for “ONE TOUCH” 6-2 43 biank EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model q Yes. q ]No OHCA Circuit Primary Directory Model Type Number - - - - Intercom Number - Station Name ICM Group ------___[? None - - Pickup Group Next Hunt Station Class of Service q EXT ---- Data Line Security Automatic Callback-Trunk Parallel Connect q Yes, [7No q Yes, ONo q Yes, q No - ONone - Number SDN COS 1 DN-02 q q DN-03 /C]Station.ODN 1 DN-01 PDN Station,ODN Station,nDN DN-05 /-JStation,CJDN DN-06 q DN-07 q q q q q DN-09 DN-10 DN-11 DN-12 Station. q DN Station,uDN Station,ODN ]Station,nDN Station.uDN ]Station, q DN DSS Key DSS Key Type 01 02 I 03 I I 04 I 6 1 flStation.nDN DN-08 0 Night Ring q Station,~DN DN-04 1PF Key 1PF Key Type 1 Day Ring I 07 08 09 10 11 6-3 06 I Number EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Model Type q Yes, q Nz - - - - - Pickup Group Next Hunt Station ------__-J None - q EXT c N o n Class of Service - e - Dyes, q N3 Data Line Security Automatic Callback-Trunk ayes, 0~3 Parallel Connect q Yes, q N3 q q q DN-10 DN-11 DN-12 PF Key PF Key Type 6-4 Station.ODN Station.C]DN tation.nDN EXTENSION-STATION Staticn Equipment Nc Item Set Data Telephone Type and MG:?I 1 Type 3HCA Circuit IYes. ~NO P r i m a r y D i r e c t o r y Numt;Intercom-Numbtr - Station Name Model - /- - - - - - - - A =None - - ICM Group Pickup Group Next Hunt Station 7~x1 E N o n Class of Service ;Data Line Security / ZYes ]No A u t o m a t i c Callback-in-( 12Ye.s. ~NO Parallel Connect I 12 / IYes. I I ~NO 1 6-5 e EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Model Type q Yes.[INo _--- ___--_---- Pickup Group JNone q EXT---_ Next Hunt Station Class of Service - aYes, CNo Automatic Callback-Trunk Dyes, Parallel Connect [7Yes, CNo CNo Data Line Security Numbe I q N- 1 I SEN COS DN-02 [~Stkon, ODN I )N DN-03 j-Jtztim, DC )N DN-01 PDN q DN-04 1 Night Ring Day Ring Stz5on,ODN InStdcm,~DN 1DN-06 1 I I m-07 i DN-08 1 I DN-09 DN-10 DN-11 II NI jnStation,nDI I l~Station,~D~ 1 I I I 1 I f$tion.~DN 1 q q Station, q DI Station,nDI DSS Key jDSS Key Type 01 j 02 j 03 i 04 / 05 j 08 07 I f 08 j Number EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk PeFalletconRest~ Set Data Type Dyes, q No Model - - - __----__-- q None q EXT ---ONone - - q Yes., q No q Yes, q No q Yes, ONo 6-7 EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model Model Type OHCA Circuit q Yes, ~NO Primary Directory Number - Intercom Number - Station Name - ICM Group - Pickup Group - Next Hunt Station q EXT ---- Class of Service - Data Line Security - - - - - - - ONo I - ONone aYes, Number 1 DSS Key DSS Key Type Number 01 I I 0 - q Yes, ONo Parallel Connect 01 - - UNo I - ONone Automatic Callback-Trunk aYes, 1 PF Key 1PF Key Type 1 - 03 I 08 1 6 07 I EXTENSION-STATION Station Equipment No. item Telephone Type and Model Set Data Model OHCA Circuit Type ayes,q Primary Directory Number - tnfwcomNtrmber - Station Name __-_------ ICM Group - Pickup Group - Next Hunt Station q EXT - - -- Class of Service ayes, [7No Automatic Callback-Trunk Dyes, q ]No Parallel Connect ayes. ONo Data Line Sacurity Key Key Type ON-01 PDN - - ]No - - ONone - [7None SON COS Number q q q DN-02 DN-03 DN-04 Station, q Day Ring DN Station,nDN Station,DON aStation, /JDN DN-06 uStation,uDN q DN-06 MOT- . Station.nDN /JStation,~DN DN-08 jJStation,ODN DN-11 q q q DN-12 [7Station.j-JDN DN-09 DN-10 PF Key PF Key Type Night Ring Number Station,C)DN Station,nDN Station,nDN DSS Key DSS Key Type 01 01 02 03 04 05 06 07 08 6-9 1 Number i EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Set Data Type ayes, Model (7No IntercomNumber Station Name --_-e------e- ICM Group Pickup Group - Next Hunt Station q EXT ---- Class of Service - Data Line Securiiy Automatic Callback-Trunk c]Yes. Parallel Connect 2 None ONone ~No q Yes, [?No q Yes. ONo 6-10 B EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Model TYPO q Yes. q No -------o-e - ONone Next Hunt Station q EXT-__- Class of Service Data Line Security Automatic Callback-Trunk - Parallel Connect Key Key Type DN-01 PDN PF Key 1PF Key Type ONone - q Yes, ON0 Dyes, q ]No q Yes, q No SDN COS Number Day Ring Night Ring j-J.tation,uDN Number I 1DSS Key 1DSS Key Type I 01 01 02 02 I 03 , Number I I 04 05 06 06 07 07 I 08 ! 06 I 09 10 11 6-11 1 I EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Model Type Dyes., [7No - - - - - - - - - - - - [7EXT Data Line Security Automatic Callback-Trunk Dyes, q aYes, q Parallel ayes. Connect - ONone ---_ ONone No No ~NO 6-12 EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model OHCA Circuit Primary Directory Number Type Dyes, InterccrmHumber - Station Name ICM Group __---_---- Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Model ONo _--- - - 0 None q EXT-___ - ayes., q No ayes, q No q Yes, q No ONone EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit q ]Yes, ONo Primary Directory Number intercom Number - Station Name ICM Group -------A-0 None - Pickup Group Next Hunt Station - Automatic Callback-Trunk Parallel Connect DN-01 - - - - q EXT_--- Ctass of Service Data Line Security 8 Model Type I ONone - [7Yes, q No q Yes, ONo ayes, ONo SDN COS Number q PDN blStation.I7DN 1 I I ON-03 1 l&tation;iDN 1 q Station,nDN DN-05 flstation. IlDN DN-06 lTN4.z - q q DN-08 IlStation. IlDN Station,CjDN Station,nDN DN-11 q q q DN-12 flStation,nDN DN-09 DN-10 PF Key PF Key Type Number Station,nDN Station,nDN Station.ODN DSS Key DSS Key Type 01 01 05 05 06 06 07 -. 07 08 08 09 10 11 12 6-14 Night Ring ]Station,nDN 1DN-02 1 I DN-04 Day Ring I Number I EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Model OHCA Circuit TYPO ayes., Primary Directory Number - Intercom Number - Station Name - - - - - - - - - - ICM Group - Pickup Group - Next Hunt Station q EXT ---- Class of Service - ONo - - - Dyes, q Data Line Security Automatic Callback-Trunk ayes., q [7Yes,q Parallel Connect - ONone ONone No No No q q DN-11 DN-12 PF Key PF Key Type cl1 02 02 03 03 04 04 05 05 06 06 1 I q DN Station.ODN DSS Key DSS Key Type Number 01 12 Station. I 6-15 Number EXTENSION-STATION Station Equipment No. Set Data item Telephone Type and Model Model OHCA Circuit Type c]Yes,q No Primary Directory Number - - Intercom Number Station Name ____------ CM Group - Pickup Group Next Hunt Station Class of Service - Data Line Security Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN 1 PF Key 1PF Key Type 1 1 06 - - ONone - q ]EXT_--- ONone - q Yes, ONo q Yes, ONo ayes, ~NO Number q I 06 07 06 I 11 , Station, q 12 6-16 I Night Ring DN 1 DSS Key 1DSS Key Type 1 Number 1 I 10 I Day Ring SDN COS Number EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN Set Data Model Type q jYes.ONo - - - _----_---- q - ONone EXT ____ ONone - ayes, q No ayes, ONo aYes, ONo Number SDN COS q q DN-02 PF Key 1PF Key Type Number. I Station, q Day Ring DN Station,nDN DSS Key !DSS Key Twe 1 05 06 f 17 Night Ring Number I EXTENSION-STATION Station Equipment No. Set Data item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number - Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Model Type OYes, q - ON0 - - --e--w---ONone EXT ONone - - / aYes, q No Automatic Callback-Trunk I aYes, ~No Parallel Connect 1 q Yes, ONo 1 SDN COS 1 Number L DN-01 q PDN flstation, DN-03 q q /JStation,aDN DN-05 nStation,lI)DN -DN-O7 - DN-08 DN-09 DN-10 DN-11 1 DN-12 PF Key PF Key Type Number , 02 Station,uDN Station,uDN Station,nDN Station,nDN Station, q DN Station.ODN Station.ODN DSS Key DSS Key Type Number 01 01 I DN Station,ODN DN-04 q q q q q q q Night Ring ( Station,flDN DN-02 DN-06 Day Ring 1 I 03 04 I 04 I 05 I 07 I 06 06 I 05 I 07 08 \ 10 11 12 6-18 1 I EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Type Dyes., Model ?No - - - -____----- q EXT ____ aYes, q ONone ONone ~No Yes, NO Dyes, ~NO 6-19 EXTENSION-STATION Station Equipment No. r t Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name CM Group Pickup Group Next Hunt Station Set Data Type Dyes,q Model jNo - - - _--------- IJNone q EXT ---- Class of Service Data Line Security q Yes, ONo Automatic Dyes, Callback-Trunk L Parallel Connect - ONone - ONo q Yes, q No 6-20 EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model q Yes, q No OHCA Circuit Directory Primary Model Type Number IntercumNumber Station Name ICM Group - Pickup Group -- Next Hunt Station [7EXT Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN 0 None ___- ONone -- q Yes. q No ayes, q No q Yes, q No Number Day Ring SDN COS Night Ring IlStation.nDN q q DN-02 DN-03 DN-04 Station,ODN Station, q DN nStation.nDN DN-05 q DN-06 llStation.llDN q q Dt+oic - Station, q DN Station,uDN q ]DN OfStation, q DN q Station,uDN q Station.aDN q Station,nDN DN-08 DN-09 DN-10 DN-11 DN-12 1PF Key 1PF Key Type 1 Station, DSS Key DSS Key Type 01 01 02 02 I 03 I 03 04 04 05 05 1 06 1 06 07 1 07 08 I 11 I I 12 I 6-21 Number EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Model OHCA Circuit Type aYes, Primary Directory Number - Intercom Number - Station Name ___---_--- ICM Group - Pickup Group - q Next Hunt Station Class of Service - - 0 None EXT z N o Automatic Callback-Trunk aYes, DN-01 n ENo ~No I SDN COS Number q q q PDN DN-02 DN-OS DN-04 DN-05 e q Yes, [3No Parallel Connect I - - ayes, Data Line Security (7No Station,uDN Station,nDN Station,ODN jJStation,nDN q DN-12 1 Station,ODN lnStation.ODN 1 6-22 Day Ring Night Ring EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Set Data Model Type aYes, - - C:;o - ___------- q -J None IEXT ____ Data Line Security aYes, Automatic Callback-Trunk Dyes. Parallel Connect Key Key Type DN-01 PDN - ONone C!/o c::3 q Yes, C:do Number SDN COS q Day Ring Station,C]DN DN-02 IlStation. IlDN DN-03 iStat& ODN q . DN-04 , DN-05 q Station, DN astation, [7DN DN-06 /-JStation.nDN DN-07 q DN-08 f-JStation,ODN q q q q DN-09 DN-10 DN-11 DN-12 PF Key PF Key Type Night Ring Number q Station, DN Station,ODN Station,nDN Station,ODN Station,ODN DSS Key DSS Key Type 01 05 06 07 07 08 08 6-23 _ Number EXTENSION-STATION Station Equipment No. r Item Set Data t- Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel t 72 Connect Model Type q Yes. q No -_-- - - - - - - - - - - 7 None q EXT__-- aNone - q Yes, q No Dyes, q N3 q Yes, ONo I 6-24 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Set Data Model Type q Yes, q No ---- Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect -__-A----- -- q ONone EXT [7None -- q Yes, q ]No q Yes, q No q Yes, NO 6-25 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Set Data Type IYes, Model ON0 - - - __-------- Pickup Group Next Hunt Station - 0 None Z]EXT - - Class of Service - Data Line Security Automatic Callback-Trunk ayes, CNo CYes, ayes, ONo CNo Parallel Connect PF Key PF Key Type - - ONone - Number DSS Key DSS Key Type 01 01 0 Number 2 04 05 ., i 06 06 07 07 08 08 t I 09 I I , I 10 11 12 I 6-26 I 1 I EXTENSION-STATION Station Equipment No. Item 1Telephone Type and Model j OHCA Circuit Primary Directory Number Set Data Type Model q Yes, ONo ---- Intercom Number Station Name ICM Group Pickup Group -_--____-- Next Hunt Station q EXT ---- Class of Service Data Line Security Automatic Callback-Trunk -- Ii Parallel Connect 1PF Key 1PF Key Type 1 -- ONone ONone Dyes, q No q Yes, ONo q Yes. q No Number I DSS Key DSS Key Type 01 01 0 2 I 03 I 04 05 05 06 07 1 08 ! 08 08 10 I 11 I I 12 t 6-27 Number EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Type OYes. q No Model- - ---- Intercom Number Station Name CM Group - Pickup Group Next Hunt Station -- q EXT ____ Class of Service Data Line Security 1 Key Type ONone -- Automatic Callback-Trunk Parallel Connect 1 Key ONone 1 ayes, q ]No OYes, q No q Yes, q No 1 SDN COS 1 Number ON-03 q q q ON-04 [7Station,uDN ON-05 OStation.ODN ON-06 (JStation,DDN ON-07 uStation,[7DN ON-08 i--JStation.nDN ON-01 PDN ON-02 q q q q ON-09 ON-10 ON-1 1 j ON-12 PF Key PF Key Type 01 02 02 03 03 04 04 I I 05 06 06 07 I 08 08 09 I 10 05 I I 11 12 6-28 Night Ring 1 DN DN Station,nDN jStation,nDN Station, DON Station,uDN Station, q DN DSS Key DSS Key Type Number 01 07 q Station, q Station, Day Ring 1 I I . J Number EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Set Data Type ayes, q - - - No - - i--m-----C]None - q EXT-_-- Class of Service Data Line Securiiy Dyes, q Automatic Callback-Trunk Parallel Connect ayes, Key Key Type 1DN-01 1 PDN Model ONone No ONo q Yes, ONo Number I 01 q q Station. Station. q q DN DN 1DSS Key 1DSS Key Type 1 Number I 03 04 05 08 07 ’ I 08 I I 05 I I 07 II I 08 09 10 11 I 12 Night Ring InStation.[-lDN I DN-11 DN-12 PF Key PF Key Type Day Ring SDNCOS 1 I I 6-29 1 I Number EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Type aYes, Primary Directory Number tntercom Number - Station Name ICM Group - - - - - - - - - - Pickup Group Next Hunt Station - Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect - - Model ONo - - ONone q EXT__-- ONone - q Yes, ONo q Yes, ONo q Yes, ONo 6-30 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circirit Primary Directory Number lnterccun Number Se1 Data Type Mccel q Yes, C K.0 ----- Station Name ICM Group - Group Next Hunt Station Class of Service - Pickup - 1None q EXT -- --- Parallel Connect q Yes, EN0 q Yes, Ct:o q ]Yes, Et:0 Key Key Type Number DN-01 PDN Data Line Security Automatic Callback-Trunk ONone SDN COS q q q q q DN-02 DN-03 DN-04 DN-05 Day Ring Night Ring ]Station,ODN q Station, q Station, DN DN Station,fJDN Station,ODN /-@ation,q DN DN-06 astation, q DN DN-07 DN-06 q DN-09 nStation,ODN DN-10 q Station,nDN Station.nDN astation, q DN DN-11 astation, q DN DN-12 1PF Key 1PF Key Type 1 Number DSS Key DSS Key Type Number 01 06 06 07 07 I 08 I 08 09 10 11 t 12 I 6-31 I EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OliCA Circuit Primary Directory Number TYPO GYes, q No Model Intercom Number Station Name ICM Group ----e----e- Pickup Group Next Hunt Station Class of Service GExT CNone - Data Line Security Automatic Callback-Trunk Key Type DN-01 PDN - a y e s , aYes, ONo ONo ayes, q No Parallel Connect Key ONone -- Number SDN COS DN-02 q q DN-03 loStation.nDN q DN-06 jJStation,ODN q q DN-08 DN-09 DN-10 q I 1 Station, ODN Station,ODN 02 01 02 ! 04 05 Station,nDN DSS Key DSS Key Type Number 03 ! I Station,ODN lostation, q DN } i j PF Key PF Key Type 1 / 01 i 1 ! astation, /JDN / DN-12 / 1 fJStation,aDN i DN-11 j Station,ODN DN-05 DN-07 J Station,ODN astation, q DN DN-04 Night Ring Day Ring I 04 I 05 MI 06 I 6-32 B Number 1 EXTENSION-STATION Station Equipment No. item Telephone Type and Model OHCA Circuit Primary Directory.Number Model Type ayes, q No Intercom Number Station Name - - - - - - - - - - - - - CM Group Pickup Group - Next Hunt Station Class of Service q EXT ---- Data Line Security Automatic Callback-Trunk Parallel Connect [7Yes, Key Key Type DN-01 PDN PF Key PF Key Type I Set Data o t 02 t ONone ONo Dyes, q No Dyes, ONo Number SDN COS astation, q Day Ring DN 1DSS Key 1DSS Key Type 1 Number Night Ring Number I I I 03 04 05 06 07 - 0 None 03 04 05 06 07 _ 08 08 09 6-33 I I EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Type OHCA Circuit Primary Directory Number Intercom Number Eyes. Station Name ---------- ICM Group Pickup Group - Next Hunt Station EEXT Class of Service Data Line Security a y e s , ENO Automatic Callback-Trunk Paraflel C6nnect Eyes, Q Model - ENO ENone ---_ ONo [7ves. q No ONone EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Type aYes,q No - - Intercom Number Station Name ------e--w - ICM Group Pickup Group Next Hunt Station Class of Service - - - - Model ONone q EXT___- ONone Dyes, Data Line Security ~NO Automatic Callback-Trunk aYes, ONo Pafaw~o~t [7Yes. q No 6-35 EXTENSION-STATION Station Equipment No. item Set Data Telephone Type and Model Model Type q Yes.NO OHCA Circuit Primary Directory Number intercom Number - Station Name ICM Group Pickup Group -__------ONone - Nexr Hunt Station Class of Service q EXT___- - - - - ONone - ayes. q No q Yes, ~NO --- q Yes, q No Data Line Security Automatic Callback-Trunk ParalleC Connect L DSS Key D6S Key Type 1PF Key 1PF Key Type 1 01 Number 01 02 I 03 I 04 ^'_ 05 05 06 06 07 07 I 08 I I 09 I I I 10 I I 08 6-36 I EXTENSION-STATION Station Equipment No. F -‘I Set Dz:z Item Telephone Type and Model OHCA Circuit Primary Directory Number Model Type q Yes, ~NO Intercom Number - Station Name - - - - - - - - - - ICM Group Pickup Group Next Hunt Station ONone TEXT _ ENone Class of Service Data Line Security Dyes., .lNo ayes, ‘INo Automatic Callback-Trunk L Parallel Connect Key DN-01 - - - - q Yes, JNo Number Key We PDN SDN COS !mStation,ODN DN-03 1 iCJStation,uDN) ._ DN-05 1 I 1 $JStation, q DN I InStation,nDN 1 )f-J%tion,uDN DN-09 I DN-10 DN-11 !llStation,nDN 1 i!OStation,EDN / /OStation, q DN I DN-12 Instation.nDN 1 I DSS Key IDSS Key Type 1 [key 1PF Key Type 1 01 02 I . 02 03 04 05 06 07 06 I ifiStation,zDN ! DN-09 r 1 iaStation,DDN DN-04 DN-07 Night Ring J-J%tion,ODN DN-02 DN-06 Day Ring 06 I - 6-37 Number 1 I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Securiiy Set Data Mdel TYPO OYes, EN0 - - - -_-------ONone - [7EXT aYes, Automatic Callback-Trunk ayes, Parallel Connect Dyes, - - - CNo CNo CNo 3 6-38 ONone EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name CM Group Pickup Group Data Line Security Automatic Callback-Trunk Farabl~Connecf DN-01 Model No - - - ___------- Next Hunt Station Class of Service b&v 1 K e v Type Dyes, q TvDe 1 0 None q EXT ---- ONone - q Yes. q No ayes, q No ayes. q No Number t PDN SDNCOS 1 Night Ring I fJStation.nDN DN-02 aStation,q DN DN-03 OStation, q q Station, q DN-04 DN DN DN-05 i-JStaton, C]DN DN-06 q DN-07 ~Station. ODN DN-06 @tation, q DN DN-09 OStation, ODN DN-10 (-J%tion.C]DN DN-11 (-JStation.q DN q DN-12 PF Key PF Key Type Dav Rina 1 Number Station,fJDN Stat-m.ODN DSS Key DSS Key Type 01 6-39 4 Number EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Model Type q Yes, q No - - - ___-----__ - ONone q EXT_--- Next Hunt Station Class of Service - Data Line Security Automatic Callback-Trunk Parallel Connect ONone - q Yes, ONo q Yes, ONo ayes, q No DSS Key DSS Key Type 01 05 06 - I 07 I 07 I 08 08 09 I 11 I 6-40 Number EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Set Data Model Type q Yes. q No .Intercom Number Station Name CM Group -------w-v Pickup Group Next Hunt Station Class of Service [IIEXT _ Data Line Securiiy Automatic Callback-Trunk Paraitet Conrrect Byes., q No [?Yes, q No C]Yes, q No PF Key PF Key Type - - 0 None _ _ _ ONone -- 1DSS Key 1DSS Key Type 1 Number I 01 01 Number I 02 04 05 06 06 07 07 08 08 I 09 I I 6-41 1 I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model Set Data Model Type OHCA Circuit Primary Directory Number Intercom Number Dyes, q No Station Name ICM Group ____------ Pickup Group q None q EXT__-- Next Hunt Station Class of Service Data Line Securiiy Automatic Callback-Trunk Parallel Connect - - - - - - - ayes, q No Dyes, ONo q Yes, q No ONone EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Set Data Type aYes, q - - - No Model - - Station Name ICM Group -___------ Pickup Group - Next Hunt Station q EXT___- Class of Service (7Yes, q No q Yes, ONo Data Line Security Automatic Callback-Trunk Paraftet Connect - 1 None q ]None q ]Yes, [7No Key We ] LW08 @ation, DN-10 DN-11 DN-12 0 q Day Ring Night Ring DN q Stat-bn,nDN q Station.~DN q Station,nDN q Station.~DN DN-09 J PF Key PF Key Type Number SDN CO’S DSS Key DSS Key Type 01 1 6-43 \ Number EXTENSION-STATION S;z:ion Equipment No. Item 1 Set Data -I Tslephcne Type and Model COCA Circuit hnary Directory Number Irwcom Numb& Wion Name KM Gnup P&up Group Next Hunt Station Ciass, 04 Service Data Ljne Security Pizornztic Callback-Trunk Puallel Connect Du-08; DH-09: lx-10: w-11 1 m-12 g Model Type q Yes, q ]No - - - I - - - - - - - - - - - 0 None CEXT - - - - ONone - q Yes, CNo ayes, q ]No Dyes, CNo q Station, q DN q Station,~DN fJStation. q DN q ]Station,ODN q Station, q DN EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Set Data Model Type OYes, - - ONo - - - - - - - - - - - - ONone q IEXT ____ ONone - - Data Line Security Automatic Callback-Trunk q Yes, ONo q Yes, q No Pafa+k?I Cefwlect- c]Yes. Key Key Type DN-01 PDN ONo Number SDN COS j-JStation,ODN DN-02 q DN-03 flStation,ODN q q q q q q q q q ON-04 DN-05 DN-06 ’ D&07 -‘ DN-08 DN-09 DN-10 DN-11 DN-12 I Day Ring 10 t2 I I 6-45 Station, Station, q q DN DN Station,ODN Station./-JDN Station, ODN jStation, q DN Station, ODN Station,QDN Station,C]DN Station,ODN Night Ring EXTENSION-STATION Jip-nent No. Set Data Type and Model Type Jit ayes, Model [7No xtcry Number Jmijer ie ---------- JP ;taisn -- l-vice Lecu rity Callback-Trunk -- 7riWt aNone q EXT-___ ONone c]Yes, q No Dyes, nNo Dyes. ~NO ling Key Type Number 6-46 EXTENSION-STATION It No. Set Data 3 Model Type umber ---- -- Model ONone q EXT_-__ ONone -- -Trunk q Yes, q No q Yes, NO q Yes, q ]No Number SDN COS Day Ring Night Ring Night Ring umber Number 6-49 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk ParattetConnect Key Key Type DN-01 PDN Set Data Model Type Dyes, UN0 - - - - - - - - - - - - - 0 None q EXT-__ayes, ONone UNo q No q ]Ye.s, q No ayes, Number SDN COS DN-02 DN-03 DN-04 q DN-05 q q q q Day Ring Station,nDN q Station. q Station, DN Station.C]DN Station,fJDN fJStation, [7DN DN-07 OStation, DN-08 [7Station, /JDN DN-09 f-JStation,~DN DN-10 C]Station, DN q q DN DN-12 PF Key PF Key Type Number , DN DN-06 DN-11 q q DN tation,[7DN station, q DSS Key DSS Key Type 01 01 07 08 09 6-50 Night Ring Number 1 EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number lnfercom Model Type q Yes, ~NO Number Station Name ICM Group Pickup Group Next Hunt Station -- q EXT ____ Class of Service Data Line Security Automatic Callback-Trunk PaUz.LCannectKey Key Type DN-01 PDN ONone oNone -- Dyes, q No q Yes. q No ayes, q No Number Night Ring flStation.nDN DN-03 q astation, q DN-04 1 (nStation,nDN DN-02 @tation, 1PF Key 1PF Key Type 1 01 02 02 I DN DN 1 DSS Key DSS Key Type Number 01 03 1 Day Ring SDN COS 03 I -_ 08 09 6-51 Number EXTENSION-STATION Station Equipment No. item Set Data Telephone Type andModel OHCA Circuit Primary Directory Number intercom Number Station Name ICM Group Pickup Group No - - - - - - - - - - - - - - - Data Line Security Automatic Callback-Trunk Parallel Connect .I Key 1 Key Type 1 1 PDN Model 3 None j I1 q EXT - - - - Next Hunt Station Class of Service 1 DN-01 Type aYes,q ONone - q Yes, ONo q Yes, q No , q Yes, q No Number 1 1 SDNCOS 1 k-IStation. nDN q q q q DN-02 DN-03 DN-04 Station,uDN Station,nDN Station,C]DN DN-08 q /-Jtation, q q Station, q astation,q DN-09 astation, [7DN DN-10 q DN-05 DN-06 D&O? Station. DN DN DN DN q DN f-&tat&t, q DN q Station,ODN DN-11 DN-12 6-52 ]Station, Dav Rina Niaht Rina 1 I I EXTENSION-STATION Static3 Equipment No. Set Data Item Teiepbone Type and Model OHC A Circuit Primary Directory Number interom Number Static n Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Para2el Connect PF Key Type 1 Type Model Dyes. q ]No ---_ -e------e- -- ONone q EXT-_--ayes,ONo q Yes, q No ayes, ONo ONone DSS Key DSS Key TyPe 01 02 03 04 05 06 07 08 09 k I 08 10 11 t 12 6-53 Number EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Intercom NumberStation Name ICM Group - Data Line Security Automatic Callback-Trunk ParaUeLCdnnect Key TY pe P - - - - - - - - - - - - - D c None OEXT -_-- Class of Service DN-01 q Yes, ‘~Nc - Pickup Group Next Hunt Station Key Model TYP* ENone - ayes, q Nc aYes, q Nc Dyes, q NC J Number i SDN COS N -DN-02 iuStaticn,ODN DN-03 \~Station,~DN DN-04 f-JStaticn.nDN DN-05 !OStation,nDN DN-06 iilStation.ilDN DNm @ation.ODN DN-06 j-Jtation,oDN DN-11 q Station, q DN q Sta!ion,ODN q Station,~DN DN-12 /-JStation, /-JDN DN-10 1PF Key 1PF Key Type 1 I 01 Number 1DSS Key IDSS Key Type 1 I 01 02 02 03 I 03 I 04 05 . . - -. 06 Night Ring dlStakn.ilDN DN-09 .j Day Ring I 06 07 07 08 08 09 10 11 t2 6-54 I Number I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Set Data Type Eyes. Model ~No ---_ Intercom Number Station Name ICM Group Pickup Group ------w--v -- ONone Next Hunt Station Class of Service q EXT ---- Data Line Security Dyes, ONo Automatic Callback-Trunk Parallel Connect aYes, ~NO GYes, [7No 1PF Key 1PF Key Type 1 06 [3None 1 Number 1 DSS Key 1DSS Key Type 1 06 I 07 07 08 08 6-55 8 I 1 I Number I EXTENSION-STATION Station Equipment No. Set Data Item Telephon? Type and Model f Type OHCA Circuit q Yes, NO Primary Directory Number Intercom Number Station Name Model -___------- KM Group Group Pickup g None Next Hunt Station Class of Service q Data Line Security a y e s , ~No Automatic Callback-Trunk Parallel Connect aYes, 1PF Key 1PF Key Type 1 IEXT ____ ONone -C!No q Yes, q No DSS Key DSS Key Type Number Number 01 01 02 I 03 I 04 1 05 I 06 06 1 07 07 04 I 05 I 08 I I 09 I I 10 I 11 t 12 08 I I I 6-56 I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number tnterccsmmelStation Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk FaralleLCannect _ PF Key PF Key Type Set Data Model Type q Yes, CNo - - - - - -----_---ONone OEXT _-__ Dyes, CNo [?None q Yes, CNO aYes, CNo 1DSS Key IDSS Key Type I Number 06 08 06 ,07 07 08 08 09 I 10 I I 11 ' 72 6-57 +b 1 Number I EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Type OHCA Circuit Primary Directory Number Intercom Number Dyes. Station Name CM Group Pickup Group ---m-e__-_ - Next Hunt Station q EXT__-_ - Class of Service Data Line Security - Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN - Model - q Nc - - - - C None ONone - C]Yes, q Nc /-&es, q Nc c]rles, q Nc SDN COS Number q q q q DN-02 DN-03 DN-04 DN-OS Day Ring Station,uDN q Station, q Station, DN DN Station, fJDN (JStation,aDN DN-09 q q q q DN-10 1 (UStation. DN-11 astation. fJDN DN-12 OStation,[7DN DN-06 DN-O? DN-08 12 Night Ring I I 6-58 Station,f-JDN Station,C]DN Station,nDN Station,nDN q DN1 I I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number intercom Number Station Name ICM Group Set Data Type [7Yes, - - Model q No - - - _---_----- ONone Pickup Group Next Hunt Station q EXT__-- Class of Service Data Line Security Ryes, ONo Automatic Callback-Trunk ParaUeCCorwest- ayes. ONo Key Key Type DN-01 PDN ONone q Yes, q No SDN COS /-Jtation.ODN Number q DN-02 ON-03 06 06 07 07 08 08 I 1 09 10 11 t 12 Station,nDN 1DSS Key 1DSS Key Type I 1PF Key 1PF Key Type 1 Night Ring aStation, q DN llStation.ilDN DN-04 I Day Ring t 6-59 9 I 1 I 1 EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Model Type OHCA Circuit q Yes, ONo Primary Directory Number - - Intercom Number - - Station Name - - - - - - - - - - ICM Group - Pickup Group - Next Hunt Station q EXT ____ Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN PF Key PF Key Type - - - - ONone ONone - [7Yes, q No Dyes, q No q Yes, q No Number SDN COS q Number 02 03 03 04 04 05 05 06 06 07 07 _ 08 08 09 t 10 I I 11 I Night Ring Station,(~DN 1DSS Key 1DSS Key Type 01 Day Ring Number I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number tntercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect. PF Key PF Key Type t I Set Data Model Type q Yes, q No - - - - - -e---e---JNone - q EXT ---Dyes, ONone GNo q Yes, ONo ayes, q ]No 1DSS Key 1DSS Key Type f Number 01 02 I I 03 I 04 I I 05 06 07 t 08 - 08 t 10 11 t2 t 06 07 09 t 05 I 6-61 I I Number I EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Type aYes,q Model No - - - - - - - - - - - - - - ENone Pickup Group Next Hunt Station q EXT_--- Class of Service Data Line Security Dyes,q No Dyes,q Nc Automatic Callback-Trunk Parallel Connect q ONone Yes, q Nc 6-62 Q EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Model OHCA Circuit Type Dyes, q Primary Directory Number - - Intercom-Number - - Station Name - - - - - - - - - - ICM Group - Pickup Group - Next Hunt Station q EXT ---- Class of Service ayes,q Data Line Security Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN No - - ENone - q ]None No q yes,ONo q Yes, q No Number SDN COS q PF Key PF Key Type 0 01 2 02 I 03 05 ! 05 07 I 1 08 09 11 I I I 12 I 1 6-63 a I 06 t 0’ I I 03 04 I 06 . Station, q DN 1DSS Key 1DSS Key Type 1 Number I 04 1 Night Ring station,q DN DN-02 I 01 Day Ring 08 1 Number I I EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name KM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Model Type q Yes, q No - - - -----e--e- C]None q EXT___Dyes, ONone ONo q Yes, q No ayes, ONo 6-64 1 EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Type OHCA Circuit Dyes. t?imaryDi~ctofy Number Model iINo ---_ Intercom Number - Station Name CM Group --------en Piiup Group - Next Hunt Station Class of Service q EXT ---- - - - - ONone ENone - Data Line Security aYes, UNo W Callback-Trunk Dyes. ONo Parallel Connect q Yes, q No Key Key TY pe DN-ol PDN Number Day Ring SDN COS q S:ation.nDN q DN-02 OStation. DN-03 ~Statkln. DDN DN-04 ilSxtion.llDN DN-05 .- fjbfj& .- DN uSztion.f-JDN q DN-07 Station,ODN fJStation.ODN DN-09 q q DN-10 OStation.uDN DN-11 q DN-12 OStation, DN-08 09 to 11 08 , Night Ring 08 12 6-65 Station.ODN Station,uDN Station,/‘JDN 1 q DN I 1 EXTENSION-STATION Station Equipment No. hem Se! Data Telephon? Type and Model Mwel Type OHCA Cicuit IYes, q No Rimary Cirectory Number - - Intercom Number - Station Name - - - - - - - - - - ICM Group - Pickup Grxp - Next Hunt Station JEXT - Class of Service - - - ONone - - - - Data Line Security ,xYes, q No Automatic ‘IYes. Callback-Tank Key Type DN-01 PDN ONo JYes, q No Parallel Connect Key a None - Number SON COS /-JS.:ation, q rDN-08 DN-09 q q DN-11 DN Station,nDN Station,nDN Station,ODN /-JStaion, q DN DN-12 PF Key PF Key Type DSS Key DSS Key Type Number 01 01 02 ! 03 03 04 04 05 06 07 -. 08 Night Ring [7Station,nDN DN-10 I q Day Ring I 1 I 09 I I 10 I I I I Number EXTENSION-STATION .S:z:ion Equip-+nt No. Item Set Data -5 ?phc 78 Typ? 2nd Model Type C-CA Circuit Eyes. F’-,-naty 3irec!c.-I. Nurnber - l-~xors: Numbs- - %tion Name -____----- I’. ‘A Grca p - P&up Group ONone EEXT m N o hsxt Hl;nt Statlc C dss of Service Model - ONo - - - Cza Lke Sect-:,4 Eyes. q ]No L,:omaric Calltxk-Trunk Eyes, ONo Fzrallel Connec Dyes., ~NO <:ay I Key Tyx C%-01 ; n e Number Day Ring SDN COS PDN /-JStz on,ODN Vi-02 / q c-‘M3 i fJSta:an,mDN p;-04 q : p;-@=j ! q Stson, q DN Stz.on,ODN /-‘JSt.zon, C]DN j nSta;‘on,CjDN q Stzfon,/-JDN q Sta;!on,uDN q St~~on.~DN q StatW(7DN Pi-09 i DU-10 1 lx-11 1 w-12 1 P-T Key PF Key Tge Stz:n,ODN jJStson,ODN p;-06 ; I c*%O7 C*‘i-08 Night Ring Number 1DSS Key /DSS Key Type 1 07 08 6-67 1 , I Number EXTENSION-STATION Station Equipment No. Scr Data Item Telephone Type and Model Mxel Type OHCA Circuit q Yes, ~NO Primary Directory Number _--- Intercom Number - Station Name -----__--- CM Group - Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Key DN-01 Key Type PDN - q Nc-s q EXT--__ - - ONone - q Yes, ]No q Yes, r]No q Yes, NO Number SDN COS q Day Ring Night Ring Station,f-JDN DN-02 ) DN-04 q q DN-OS j-JStation, [7DN DN-06 q DN-07 fJStation, ODN DN-08 q DN-09 nstation. IlDN DN-03 q q DN-10 DN-12 PF Key 1PF Key Type 1 06 Number DN DN Station,nDN Station, q DN Station,nDN q [7Station, q DN-11 1 q Station, q Station, Station, DN DN 1 1DSS Key IDSS Key Type 1 Number I 06 i 07 08 1 08 1 6-66 1 I 1 EXTENSION-STATION Station Equipment No. Set Data Telephone Type and Model Type OHCA Circuit Primary Directory Number aYes, Model ONo ---- Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Da?a Line Security Automatic Callback-Trunk Parallel Connect PF Key PF Key Type 0 1 L__------- -- C]None q EXT__-- ONone - ayes, ONo ~q Yes, q No ~Ryes, q ]No Number 1DSS Key 1DSS Key Type 1 02 04 06 06 07 08 6-69 Number EXTENSION-STATION Station Equipment No. l- Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Set Data Mdel Type q Yes, [7Ns _---- Station Name ICM Group __-_------- Pickup Group Next Hunt Station - Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect : Kev 1 KevI TVDe 1 -, II I : DN-01 PDN - C None q EXT___-ayes, q N3 ayes. q N3 ayes, q N3 ONone Number q q q / DN-02 ! DN-a3 1 DN-M Station,nC IN Station,nDN t t 1 StationJJCINI I q I DN-07 OStation. DCINI ~~Station.~DN q q q ! DN-11 i DN-12 PF Key PF Key Type Number 01‘ 02 03 04 05 06 07 ! 09 10 I 11 I I I I llStation,nDN t 1 DN-10 08 I - I I 1 DN-09 1 12 I fJStation,/-JDN j DN-06 fi DN-08 Night Ring Station,fJDN @tation, q C INI / DN-E Day Ring SDN COS 6-70 Station. UC)N ]Station,uDN I Station.nDN I I EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model 1Type Model OHCA Circuit / fly=, q N0 Primary Wedory Number I - - - Intercom Number jI ____-----Station Name CM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect 1PF Key 1PF Key Type 1 j 0 None : -_ jq EXT ONone ayes, q q No Yes, ONo ayes, NO Number DSS Key DSS Key Type 01 01 02 I 03 I 04 05 0 6 I 06 07 07 08 6-71 I Number EXTENSION-STATION Station Equipment No. Item Set Data Telephone hype and Model OHCA Circuit Primary Directory Number Intercom Number Station Name Model Type [7Yes, - - C]No - - - _--------0 None IJExT _ _ _ _ ONone ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk aYes, Dyes, (?No ~No Parallel aYes, ~No Connect SDN COS Number 1 DN-01 1 PDN 1 IllStarion. FlDN 1 DN-02 q J Number 01 02 02 03 03 04 04 06 05 06 06 07 07 1 04 09 12 I Station,nDN DSS Key DSS Key Type 01 11 Night Ring /JStation,ODN DN-03 I I Day Ring I I 6-72 08 Number I EXTENSION-STATION Station Equipment No. Set Data Item ’ Telephone Type and Model j OHCA Circuit I Primary Directory Number Model Type q Yes, q No ---- 1Intercom Number / Station Name i ICM Group i Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect PF Key PF Key Type 0% ONone -- q IEXT ____ ONone -- q Ye.s. q No ayes, q No aYes, ONo Number - 02 . 03 05 I 06 06 08 09 10 I 12 I I 6-73 EXTENSION-STATION Station Equipment No. r Set Data Item Telephone Type and Model Type OHCA Circuit ayes, Primary Directory Number Intercom Number - Model - ENNo - - Station Name ____------ ICM Group Pickup Group - Next Hunt Station Class of Service q EXT___- Data Line Security Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN - 13 None ONone - q Yes, EN0 q Yes, NO [7Yes, NO Night Ring q Station, q DN q Station,ODN q ]Station,nDN q Station. q DN q Station.~DN DN-02 DN-03 DN-04 DN-05 DN-08 DN-07 q q Station,nDN Station,ODN aStation, q DN DN-08 DN-09 DN-10 q q DN-11 DN-12 PF Key PF Key Type 01 Day Ring SDN COS Number q ]Station. q Station, DN DN DSS Key DSS Key Type 01 I 02 Number 13 I I I I 1 I Number I I 04 05 06 0 7 07 08 08 , 6-74 I EXTENSION-STATION Station Equipment No. item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Type Model q Yes, EN0 Station Name CM Group ---__----- Pickup Group -- J None Next Hunt Station Class of Service IJEXT _ _ _ _ ONone -- Data Line Security Automatic Callback-Trunk Parallel Connect q Yes, NO q Yes, ENo q Yes, NO 1 SDN I DN-01 , PDN DN-02 . . ,._ q C-OS DN-03 1 DN-04 ~Station, JDN 1 DN-06 fJStation, JDN 1 ON-06 ~Station,: JDN DN-07 /-J%tion. ZDN ON-08 OStation, ?JDN DN-09 OStation.: JDN DN-10 C]Station,7JDN ON-1 1 OStation,; JDN q I SF Key PF Key Type Number I 1 Night Ring 1 ! I Station. aDN DSS Key DSS Key Type I Ring Station, -JDN 1 OStation,JDN ] lostation. JDN 1 ON-12 1 Day Number 01 02 03 04 _ 06 1 I OS I 06 07 08 08 09 I 6-75 - - EXTENSION-STATION Station Equipment No. Item Telephone Type and Model Set Data Model Type Dyes. EN0 OHCA Circuit Primary Directary Number.. _ L--Intercom Number Station Name --------__ ICM Group jJ None Pickup Group Next Hunt Station q EXT ---- Class of Service Data Line Security aYes, Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN ONone CNo q Yes, CNO q ]Yes, CNo Number Day Ring SDN COS q q [7Station, q astation, q DN-02 DN-03 6-76 Station, DN DN DN Night Ring EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Model OHCA Circuit Type ayes, Primary Directory Number - Intercom Number - Station Name -------em- ICM Group - Pickup Group - Next Hunt Station q EXT__-- Class of Service - Data Line Security Dyes, - - - ONone q None - Automatic Callback-Trunk Parallel Connect (7Yes, Key - - q Key UN0 [I3No Yes. ONo ONo Type I1 1 SDN COS 1 DN-02 q OStation, q DN-OS ~Station.nDN DN-04 nStation.j-JDN DN-05 OStation,ODN DN-06 OStation,[7DN DN-07 C]Station. ODN DN-08 [7Station,f-JDN DN-09 fJStation.q DN DN-01 PDN OStation. q q DN-10 DN-12 1 I DN DN Station, DN DN1 I I!&Key Type 1 /PFKey)PFKeyTypef I 02 Night Ring Station.ODN q lostation. q DN-11 Day Ring 1 I Number I 03 I 04 06 07 I. 08 08 6-77 I I I EXTENSION-STATION Station Equipment No. r item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Set Da:a hCo&l Type q Yes, q No - - - - - ___------- q No?e q EXT---_ - c None - q Yes, ONo c]Yes, ~NO q Ye.s. q No 6-78 EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name Type aYes, Model ONo _--_-------_- ICM Group - Pickup Group - Next Hunt Station Class of Service Data Line Security EEXT --_- Dyes, Automatic Callback-Trunk ParalWCOnnect Key Key Type / ONone - 0 None ONo q Yes, ONo [?Yes. q No Number SDN COS DN-02 q q DN-03 astation, DN-01 PDN j Day Ring Station,nDN Station,C]DN DN-04 q /JStation. q DN-05 LZjStation,nDN DN-06 fJStation, DN-07 q DN-11 astation, q 6-79 DN DN Station,flDN q q Station, q DN-12 DN DN DN Night Ring EXTENSION-STATION s:aticn Equipment No. Item ‘alephone Type and Model C;HCA Circuit +imaty Directory Number ;teram Number Station Name CM Group Wwp Group ?;eti Hunt Station Zlass of Service I3ata Line Security j Mornatic Callback-Trunk ’ ?aralM Connect Set Data Type Modal q Yes, ONo ---- I -____-----ONone -q EXT ---ONone -q Yes, q No q Yes, ONo q Yes, ~NO SDN COS Number DN-11 DN-12 q q Station.ODN Station.ODN Day Ring Night Ring EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Pcictxzy Directory Number Intercom Number Station Name CM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 DN-02 DN-03 PDN DN-04 DN-05 D&o& r.. DN-07 DN-08 DN-09 DN-10 DN-11 DN-12 Set Data Type [7Yes, Model q No - - - __-------- 0 None OEXT - - Dyes, q ayes, q ayes, q - - ONone No ]No No Number SDN COS aStation, q DN q Station,ODN Day Ring Night Ring /-J&tion,ODN @ation. q DN fJStation,nDN q Station,uDN q StatioQJDN q Station.nDN jJStation,~DN @tation.q DN q q Station.nDN Station,(7DN , EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model / Type OHCA Circuit q Yes, (I:tk Primary Directory Number - - - Intercom Number Station Name - ( - ayes, Data Line Securiiy Automatic Callback-Trunk Parallel Connect DN-01 Type INone 1 q EXT _ Next Hunt Station Class of Service 1 Key - ___------- ICM Group Pickup Group 1 Key h4odel 1 ONone ~N3 q Yes. LNo , q Yes, EN3 J SDN COS Number PDN fJStation, DN-02 q Day Ring DN IlStation, IlDN 6-82 Night Ring EXTENSION-STATION Station Equipment No. Item Telephone Type and Model Set Data Model Type OHCA Circuit q Yes. GNo Primary Directory Number - Intercom Number Station Name - - - - - - - - - - ICM Group Pickup Group - Next Hunt Station Class of Service Data Line Security q EXT___- Automatic Callback-Trunk Parallel Connect - ayes, - - TJNone ENone ENo q Yes, NO Dyes, NO 6-83 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Set Data Type OYes, Model CNo Primary Directory Number intercom Number - Station Name -------F-w ICM Group - Pickup Group - Next Hunt Station q EXT ---- Class of Service ayes, CNo Automatic Callback-Trunk Dyes, CNo P’aralle r Connect ENo Data Line Security - - ayes., 0 None gNone DN-07 /JStation,ODN DN-08 (7Station.ODN DN-09 q DN-10 /JStation,ODN DN-?1 aStation, fJDN DN-12 aStation,q DN PF Key 1PF Key Type Number 1DSS Key 1DSS Key Type 1 06 07 I 10 Station,[I1DN I 6-84 EXTENSION-STATION Station Equipment No. Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Motel Type aYes, q Nc ---- Intercom Number Station Name ICM Group Pickup Group ---------- Next Hunt Station Class of Service q EXT ---- Data Line Security Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN -- C None ONone -- q Yes, q Nc q Yes, q Nc j aYes, q Nc SDN COS Number /-JStation,ODN n&&ion, q DN DN-02 DN-W @tation, q DN rLStation.llDN DN-04 q q DN-05 DN-06 DN-07 q Station, q Sta!ion, DN DN /-Jhtion,~DN DN-11 q q q q DN-12 f-Jhtion,C]DN DN-08 DN-09 DN-10 1PF Key 1PF Key Type 1 Number 06 06 -07 07 08 08 10 11 Station,ODN Station, q DN Station,ODN Station,ODN 1DSS Key 1DS.S Key Type 1 09 I Day Ring I 6-85 I 1 I I Night Ring EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Set Data Model Type JYer - - ~No - - - Station Name y--w-v---- ICM Group Pickup Group Next Hunt Station 0 None - QEXT ONone Class of Service Data Line Security - JYer DNo Automatic Callback-Trunk Parallel Connect JYer ONo JYer ~No PF Key PF Key Type - Number DSS Key DSS Key Type 01 01 02 02 03 03 04 04 05 05 06 06 07 07 06 06 09 6-86 Number EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Type OHCA Circuit ayes, Primary IXecQry Number ---- intercom Number Station Name ---------- CM Group Pickup Group -- Next Hunt Station q EXT---_ Class of Service Data Line Security D y e s , JNo Automatic Callback-Trunk Parallel Connect q ]Yes.]No ayes, ~No Model ?No ONone ONone 6-87 * EXTENSION-STATION Station Equipment No. item Telephone Type and Model Set Data Type Model Intercom Number Station Name q Yes, ONo ------___----- ICM Group - Pickup Group Next Hunt Station Class of Service -- OHCA Circuit Primary Directory Number Data Line Security Automatic Callback-Trunk Parallel Connect ONone q EXT___-q Yes, q No q Yes, q No aYes, q No ONone EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model OHCA Circuit Primary Directory Number intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Key We DN-01 PDN DN-02 I Model q Yes, ONo _---:---------- Data Line Securiiy Automatic Callback-Trunk P’arattet Connect Key Type ONone q EXT ----[ZYes, q No aYes, [7No ayes, q No q ]None 1 SDN COS 1 Number q q I DN-03 1DN-05 1 I 1 Station.ODN q DN-07 fJStation,uDN Station,nDN 1 l~Station.nDN 1 I q DN-11 [7Station, DN-12 q at Station,ODN 1 06 06 1 08 1 07 I 08 I 09 10 I I 12 I DN SS Key DSS Key Type 1 Number .- 11 q Station.nDN 02 I .I loStation.nDN DN-10 PF Key PF Key Type 1 I I I DN-06 1 DN-08 1 I DN-09 I I 6-89 Night Ring I Station.C]DN loStation.uDN I InStation,nDN 1DN-04 1 Day Ring Number EXTENSION-STATION Station Equipment No. item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Parafiel Connect DN-01 PDN - - - - ONone ZEXT Data Line Securiiy Automatic Callback-Trunk Key Type - Model ____-----0 None - Pickup Group Next Hunt Station Class of Service Key Tjlpe =Yes. 1 No ,IYes, !xYes, 3Yes. ~NO ~NO ~NO Num:e 1 SDN COS ) q DN-03 DN-04 DN-05 DN-06 DN-07 ! PF Key PF Key Type - Night Ring q DN OStation, q DN 1 fJStation,q ]DN f-J3ation,q DN q StationJJDN DN-02 DN-08 Day Ring Station, /JStation,ODN q Station,ODN IOStationJJDN N I ! Number 07 08 09 6-90 1 I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number intercom Number Station Name ICM Group Model Type q Yes, ONo - - - --------_- Pickup Group Next Hunt Station - Class of Service Data Line Security - Automatic Callback-Trunk Parallel Connect Dyes, PF Key PF Key Type 0-f I Set Data - ONone q EXT---_ ONone - q Yes.NO ONo q Yes, q No Number I DSS Key 1DSS Key Type 1 I02 I 02 03 03 04 04 05 05 06 06 07 I 08 09 6-91 07 I Number EXTENSION-STATION Station Equipment No. -r Item ’ Telephr ;e Type and Model OHCA S:rcuit Primary 3rectory Set Data TyDe Mcdel Eyes, Number IntercorI Number - - - ~NO - - - ; Station Name - - _ _ - - - - - - I C M Group - Croup Pickup - ONone - Next H-3 Station CEXT ___- ONone Class cj Service i Data Lix Security Eyes, ~No ! Automz;c Callback-Trunk Eyes, ONo : Parallel Connect ryes,q i Key Key Type PDN 1DN-01 NO Number SDN COS aStation, q DN q q ’ DN-02 Station,ODN 1DN-05 q DN /-JStation, q DN q Station,/JDN I DN-06 ilStation.flDN 1DN-07 [7Station,ODN 1DN-03 j DN-04 DN-08 q ; Station, Station,ODN ZN-09 I aStation, q DN DN-10 ; aStation. ODN q q DN-11 ; DN-12 j PF Key 1PF Key Type 01 / 02 j 03 ; Number .04 06 j -06 i 07 j O8 09 I. j 10 j 11 / 12 j L 6-92 Station,ODN Station.nDN Day Ring Night Ring EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Set Data IModel Type q Yes, ENo ---- Station Name ICM Group _----___-- Pickup Group Next Hunt Station -- Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Key ) Key Type q 0 None EXT aNone a y e s , ONo q Yes, NO ayes, ONo Number ) SDN COS 1 q DN-05 OStation, DN-06 OStation.~DN DN-07 DStation, DN-08 OStation,aDN q ]DN DN DN-10 q q DN-11 aStation. DN-12 OStation, [7DN DN-09 6-93 Station.ODN Station, q q DN DN Day Ring 1 Night Ring EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and FJodel Type OHCA Circuit aYes, Primary Directory Number Intercom Number Station Name -- Model ONo ---------- ICM Group Pickup Group Next Hunt Station OEXT Class of Service Data Line Securiiy Key We DN-01 PDN _-__ ONone -- Automatic Callback-Trunk Parallel Connect Key 0 None -- 0Ye.s. q No ayes, ONo q Yes, q No SDN COS Number q q q DN-02 ON-03 I .) Station. ODN ON-05 OStation,ODN DN-06 jJStation,nDN DN-08 q q DN-09 f’-J%tion.ODN ON-10 OStation,q DN ON-11 j-JStation.ODN ON-12 aStation.uDN Number Station.uDN Station.uDN DSS Key DSS Key Type 01 01 02 03 04 02 05 05 06 06 07 07 08 08 03 04 09 . Station,nDN (7StatioqnDN PF Key PF Key Type to 11 12 6-94 Night Ring Station,C]DN DN-04 DN-07 Day Ring Nuder EXTENSION-STATION Station Equipment No. Set Data item Telephone Type and Model Model Type OHCA Circuit q Yes, ONo Primary Directory Number - Intercom Number - Station Name _-------_- ICM Group - Pickup Group - Next Hunt Station q EXT__-- Class of Service - Data Line Security Automatic Callback-Trunk ParaflelConnect I I DN-01 - - - - - gNone ONone - q Yes, q No q Yes, q No q ]Yes, ONo Number Day Ring SDN COS PDN j-Jtation,ODN DN-02 fl.Station,nDN DN-03 astation, q DN DN-04 InStation,flDN DN-05 l&tation. EDN 1 q q DN-06 f3Nxr7 . Station,/JDN Station,nDN OStation,q DN DN-08 q q q q DN-09 DN-10 DN-11 DN-12 PF Key PF Key Type 1 Number Station,nDN ]Station,[7DN Station, q DN Station.uDN bS$~ key 1DSS Key Type 1 01 02 04 05 06 06 07 07 08 09 6-95 Night Ring EXTENSION-STATION Station Equipment No. Item Telephone Type and Model Set Data Model Type OHCA Circuit ayes,q No Primary Directory Number - - Intercom Number - Station Name ICM Group A--------- Group Next Hunt Station - q EXT_--_ Class of Service - Pickup Data Line Security Automatic Callback-Trunk Parallel Connect - - - ONone ONone - q Yes, ONo ayes, ~NO ayes, NO DN-11 q q q q q q DN-12 ,jJStation,fJDN , DN-06 DN-07 DN-08 DN-09 DN-10 1 -. 6-96 Station.C]DN Station.nDN Station,ODN Station,nDN Station. UDN Station./JDN EXTENSION-STATION Station Equipment No. Set Data item Telephone Type and Model OHCA Circuit Primaty Directory Number Intercom Number Station Name ICM Group Type q Yes, q No Model - - - -__-----__ - ONone Pickup Group Next Hunt Station q ]EXT_-__ Class of Service Data Line Security Automatic Callback-Trunk ayes. q No q Yes, ONo Parallel Dyes, Connect - ONone - ONo DSS Kev lDSS Kev Tvpe t Number I I 05 06 I 08 6-97 1 I EXTENSION-STATION Station Equipment No. Item Set Datz Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Model Oh: - - - _---v----e [TEXT Next Hunt Station Class of Service - Data Line Security Automatic Callback-Trunk Parallel Type aYes, Connect - None - CVone - q Yes, Ok2 q Yes, q K: q Yes, IJtvYj Number N$ht Ring Day Ring I I DN-02 1 I I u I DN-08 I I 3 I DN-11 1 I I 6-98 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model , OHCA Circuit Wily Directory Number intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect 12 Set Data Type Model dyes, q No ---.- A__------- DEXT - ONone ONone - aYes, q No Dyes, q No aYes. q No I 6-99 EXTENSION-STATION Station Equipmslt No. Item Set Data Telephone Type %?I! Model OHCA Circuit Primary Diiector, %umber Intercom Number Model Type OYes,q No ----- Station Name ICM Group ---------- Pickup Group Next Hunt Statior. - OEXT Class of Service Data Line Securitf ONone - -_-_ ONone -- Automatic-Callba3-Trunk Parallel Connect q Yes, q No Dyes, q No q Yes.ONo Key 1 Key Type 1 Number DN-01 1 PDN 1 SDN COS 1 1 IllStation.nDN 1 DN-03 q DN-04 IlStation. IlDN DN-05 I Station,ODN q Station,ODN DN-07 aStation, [7DN DN-08 q Station,ODN CJStation, q DN ON-09 q q q DN-10 DN-11 DN-12 Number Station. q DN Station,t]DN Station,ODN I 1DSS Key IDSS Key Type 1 01 Number I I 02 02 I 03 03 04 04 05 05 06 06 07 07 08 08 09 I 10 I I j-JStation,uDN .lstm6-- I 01 I Niaht Rina 1 nStation,q DN DN-02 1PFKevIPFKevTweI Dav Rina I I 6-100 I 1 I I I EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model Model OHCA Circuit Type aYes, Primary Directory Number - Intercom Number - Station Name ___--_---7 ICM Group - Pickup Group - Next Hunt Station q EXT ---- Class of Service - Data Line Security Aufomafic Callback-Trunk Parallel Connect Key Key We DN-Ol PDN I - ONo - - - j-J None - ONone - q Yes, q No q Yes, ~NO q Yes. q No Number q q DN loStation.q DN q Station, 01 D N , q Station. q DN 1 I DN-02 1 DN-03 DN-04 D M 1 -.-N -- Day Ring SDN COS Station, I Night Ring hstaion. IlDNi . . _. ~Station! DN-06 iDN q DN q Ststion, q DN I[rlStation. q DN1 q Station, q ]DN q Station, [7DN q Station. q DN DN-07 [3Station. DN-08 DN-09 1 DN-10 DN-11 DN-12 PF Key \PF Key Type 1 Number I DSS Key DSS Key Type I 1 Number 01 02 03 I I 06 I I 6-101 I I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Set Data Model Type c]Yes, - - NO - - - --------em 0 None - q EXT ---- ONone ayes, ~NO Automatic Callback-Trunk ayes, ONo Parallel Connect ayes, q No 6-102 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary DTrectory Number I Set Data Model Type q Yes, q No ---- Intercom Number Station Name ICM Group ___------- Pickup Group Next Hunt Station Class of Service -- Data Line Security At~tomatic Callback-Trunk Parallel Connect ONone q EXT___- ONone -- ayes, q No q Yes, NO [7Yes, q No DSS Key DSS Key Type Number 01 06 06 07 07 08 t 12 t 6-l 03 1 I I EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Type ayes, q Intercom Number - Station Name ICM Group ___--_---- Model No _--- - Pickup Group - Next Hunt Station q EXT__-- Class of Service - Data Line Security ayes, Dyes., Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN 0 None ONone - q NO q No ayes, q No Number 1 SDN q q DN-02 Station,ODN Station,ODN astation, q DN DN-03 DN-04 I DN-05 q q q q DN-06 DN-07 ?ilN-O8 Station,jJDN Station,/-JDN Station,C]DN Station. q DN jJStation,nDN DN-12 q q q q 03 03 04 04 05 05 6 06 -07 07 08 08 DN-09 DN-10 DN-11 0 COS 1 09 11 12 6-104 a Station.aDN Station,ODN Station,/JDN Station, q DN Day Ring 1 Night Ring EXTENSION-STATION Station Equipment No. Item Set Data Model Telephone Type and Model ayes.q OHCA Circuit Primary Directory Type Number intercom Number No - - - - Station Name ___------- ICM Group - Pickup Group - Next Hunt Station OEXT Class of Service [7Yes, q No q Yes, q No Data Line Security Aute Callback-Trunk Parallel Connect Key Key Type DN-01 PDN 0 None - __-- ONone q Yes, q No Number DN-03 q q q DN-04 /JStation,ODN DN-05 q DN-02 DN-07 DN-08 DN-09 DN-10 DN-11 DN-12 Number PF Key PF Key Type 01 02 1031 I 04 04 05 05 06 06 07 07 i 08 1 I 09 I t 12 Station,j-JDN Station,ODN Station, q DN q DN astation, q DN astation, q DN q Station, q ]DN q Station,nDN q )Station.ODN aStation,q DN q station, q DN DN-06 I Day sing SDN COS I I I 08 I 6-105 Station. Night Ring EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model Type OHCA Circuit ayes, Primary Directory Number - - - 3--------- Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security A&omatic Ca+lback-TrunkParallel Connect Key Key Type DN-01 - Model OFJo ONone - q EXT___- ONone - q Yes, ONo ayes, ONo ayes, q No Number 1 SDN COS 1 PDN gestation, I DN-02 q DN1 IOStation,~DN N 6-106 Day Ring 1 I Night Rkq j i EXTENSION-STATION Station Equipment Ns. item Set Data Telephone Type and Model OHCA Circuit Primary Directory Num!xr Type OYes Intercom Number Station Name - _-_--__--- ICM Group - - Pickup Group Next Hunt Station Class of Service Data Line Security Automatk Cattback-Trunk Parallel Connect - - Model ONo - - ONone q Er ---- ONone - q Yos q No aYes. q No :Dyes.. q No 6-107 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name Set Data Type Model aYes, ONo -- CM Group Pickup Group Next Hunt Station Class of Service q EXT_-__ Data Line Security aYes, Automatic Callback-Trunk Parallel Connect W Key Type DN-01 PDN - JNone - ONone -ONo -aYes, q No c]Yes, q No Number SDN COS q I PF Key PF Key Type 01 Number 03 03 . 08 08 9 10 12 Number 01 02 t Night Ring Station,ODN DSS Key DSS Key Type 02 0 Day Ring t 6-108 1 I I EXTENSION-STATION Station Equipment No. c Item Telephone Type and Model OHCA Circuit Primacy-Wedory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Set Data Model Type q Yes, q No - - - ____------ ONone q EXT___ayes, ONone ONo q Yes, q No q Ye.s. q No 6-l 09 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Securiiy Automatic Callback-Trunk Parallel Connect _ Set Data Model Type q Yes, aNo --__-_--__--ONone - q EXT_-__ - ONone - q Yes, ~NO aYes, NO q Yes, 3No 6-110 EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary-Mrectory Model Type ayes, q No Number - - - - Intercom Number Station Name ----e----v ICM Group Pickup Group - Next Hunt Station Class of Service q EXT__-_ Data Line Security Autrxwtic Callback-Trunk Parallel Connect PF Key 1PF Key Type 1 - 0 None ONone - q Yes, ONo ayes. q No q Yes, ONo Number 1DSS Key 1DSS Key Type I 04 05 05 06 06 07 -~ 08 6-111 Number EXTENSION-STATION Station EqL;pment No. Item Set Data Tele#?one Type and Model OHCA Circuti OYes, Prinsq4iredory Number Intemm Number -- Type Model (7No Statin Nama CM Group Pichp Grocq ---------- Nexr Hunt Siation Class of Seriice q EXT ---- Data Line Security Automatic Callback-Trunk PardIet Connect -- ONone ONone c)Yes, q ]No OYes, ONo ayes, ONo 6-112 EXTENSION-STATION Station Equipment No. item Set Data Telephone Type and Model Model Type OHCA Circuit Primary Directory Number q Yes, ONo Intercom Number _--------- Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Autnmatic.Callback-Trunk Parallel Connect PF Key PF Key Type 01 - - - - - - ONone q EXT_--_ - ONone - ayes, q No ayes. q No q Yes, ONo Number DSS Key 1DSS Key Type 02 03 04 06 06 06 07 07 08 08 09 S-113 Number EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Dyes, Primary Directory Number - Intercom Number Staticn Name CM Group -- Pickup Group -- Next Hunt Station Class of Service q EXT ----Dyes. q No Dyes, q No c]Yes, q No Data Line Security Automatic Callback-Trunk Parallel Connect Type - Model ~NO - - -------_-ONone ONone 1 1 [DSS Key 1DSS Key Type 1 06 06 07 07 08 1 I 08 ~~ r 6-114 I Number EXTENSION-STATION Station Equipment No. item Set Data Telephone Type and Model OHCA Circuit Priif Direetorj Number Intercom Number Mcdel J-YP~ aYes,q Nc - - - - Station Name ICM Group Pickup Group --_--___-- Next Hunt Station Class of Service q - None - EXT ONone - Data Line Security q Yes, q Ns Automatic Callback-Trunk ayes, ON: Parallel Connect Key Key Type DN-01 PDN q Yes, [7Nz Number SDN COS DN-02 q DN-03 QStation,f-J~~ ]Station,ODN q DN-05 Station,nDN /- OStation.ODN DN-06. .. QStation,nDN DN-07 q DN-08 OStation,CDN DN-09 OStation,CjDN DN-10 aStation,uDN Station,ODN q q DN-11 DN-12 PF Key PF Key Type 01 Station,ODN Station,ODN Number DSS Key DSS Key Type Number I 01 02 02 03 03 04 04 05 05 06 06 07 N$ht Ring nStation,ODN . DN-04 I Day Ring 07 I 08 08 09 10 6-115 I 1 I I I I _ I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary-Direetorjt-Nwnber intercom Number Station Name CM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Type Dyes, q Model NO _--__-------- 0 None q EXT ---- ONone - q Yes, ONo ayes, q No aYes. q No Number I DN-01 Set Data SDN COS q PDN Day Ring ’ Night Ring Station,ODN 1DN-02 1I /OStation,ODN dN-03 1 DN-04 lnStation,ODN I fJStatio1 I. _ ~DN DN-05 q t3f+a_.. -- r IlStatiol Station, q DN , I DN-07 q q q DN-09 DN-10 DN-11 Station,nDN Station,ODN Station,ODN DN-12 PF Key PF Key Type n1 Nuniber DSS Key DSS Key Type 01 Number EXTENSION-STATION Station Equipment No. r Set Data Hem Telephone Type and Model OHCA Circuit Primary Directory Number intercom Number Station Name Model Type Dyes, - - ~No - - - _--------- ICM Group - Pickup Group - Next Hunt Station Class of Service q EXT_--_ Data Line Securiiy At&ma& Caflback-Trunk Parallel Connect TY pe DN-01 PDN DN-03 1 ONone - Dyes, ayes. ONone ONo C]No q Yes, q No Number Day Ring SDN COS q Station. loStation,!]DN IN I DN-08 1 jJStation,aDN DN-08 loStation.aDN I Night Ring EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Type OHCA Circuit Primary Dire.ctory Number Dyes, - - Model ONo - - Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Securiiy Automatic Callback-Trunk Parallel Connect Kev 1 Kev TWX 1 DN-01 -- C]None q EXT_---q Yes, ONo ayes, q No q Yes, q No ONone Number 1 SDN COS 1 PDN [7Station,[7DN q q DN-02 DN-03 q q DN-11 DN-12 6-l 18 Day Ring Night Ring 1 ~ ~-1 Station,ODN 1 Station.ODN I Station,ODN Station,nDN I 1 EXTENSION-STATION Station Equipment No Item Set Data Telephone Type and Model OHCA Circuit primary Directq Number Intercom Number Station Name ICM Group Pickup Group Type Mcdel r: q Nc iYes. ----_----_---C None -- Next Hunt Station Class of Service Data Line Security ‘gEXT ONone A&xnatLCaliback-Trunk C / Y e s . ONo Parallel Connect aYes, Key Key Type DN-01 PDN a y e s , ONo / q No Number SDN COS q q q q q q q q _ DN-02 DN-03 DN-04 DN-05 . DNXE’ .. ON-07 DN-08 DN-09 I I 1 I. 1 DN-10 -._ . 1 DN-12 01 DN Station,uDN Station.ODN Station,nDN ]Station, q /- DN Station,nDN Station, q DN Station,nDN q DN flStation, q DN q Station,fJDN q Station, q DN DN-11 I q Night Ring aStation, I PF Key PF Key Type 1 ]Station, Day Ring DSS Key DSS Key Type Number Number I 01 I 02 02 03 I 04 I I 04 I I 1 06 1 I 1 08 1 05 06 08 ! I I , 09 ?O 11 . 12 6-119 EXTENSION-STATION Station Equipment k!o. r item Telephone Type and Vodel Set Data Model OHCA Circuit We aYes,q ]No Primary Directory Nurr;Ser- - - Intercom Number Station Name - ICM Group - Pickup Group Next Hunt Station - - - - __----_--- 0 None q EXT ---- ONone Class of Service Data Line Security Dyes, ~NO A u t o m a t i c Callback-Tmk Dyes. UNo Parallel Connect aYes, q No Key DN-01 I DFi-02 DN-03 DN-04 Key Type Number , / SDN COS 1 q PDN Day Ring Night Ring Station, J-JDN lnStation,nDN I q Station ,ODN q Station, q DN 1 lflStation,mDN 1 DN-06 1 1 DN-07 1 I q InStation, DN 1 Station ,[7DN q q Dij-08 DN-09 .Station,ODN [ -._ IJN-10 .- IlStation ,ODNI L DN-11 C]Station.nDN DN-12 q Station,uDN DSS Key DSS Key Type Number 01 I 04 05 06 07 . 08 08 09 6-l 20 EXTENSION-STATION Station Equipmer;: ‘40. Item Telephone Type ant Vodel OHCA Circuit prirnatp EMeetq Ni-ber Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Set Data Model Type Dyes, q No - - - - _--------- ONone q EXT__-_ ONone Class of Service Data Line Security Dyes, q No A u t o m a t i c Callback-‘ntnk ayes. ONo Parallel Connect q Yes. q No 6-121 EXTENSION-STATION Station Equipment No. Set Data item Telephone Type and Model OHCA Circuit Priiary Directory Number Intercom Number Station Name ICM Group I Model Type ayes, - - ONo - - ____------ Pickup Group Next Hunt Station q EXT__-- Class of Service Data Line Security ayes, q Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN q 0 None ONone No Yes, ONo ayes, ONo Number q 1DN-02 1 I DN-03 1 PF Key PF Key Type - Numbe’r 1DSS Kev 1DSS Kev Twe 1 02 03 04 04 05 05 06 06 07 Day Ring Night Ring loStation,nDN 1 (OStation, q DN 1 I 01 I SDN COS Station.mDN I 09 10 11 6-l 22 Number EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primq Directory Number Set Data _ Model Type q Yes, q No Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security &wmaticCallback-Trunk Parallel Connect Key Key Type DN-01 DN-02 PDN ___------- q EXT___- ONone -a y e s . ONo q Yes, q No aYes. q ]No SDN COS Number Night Ring aStation, q DN astation,q DN q q DN-03 L DN-04 1 IPFKeyIPFKeyTypeI Day Ring Number Station,uDN Station,/JDN DSS Key DSS Key Type I I Number 01 02 02 I 03 I 03 I 04 I 05 05 I I 1 1. 06 06 . 07 07 08 I 6-123 a EXTENSION-STATION Station Equipment No. r L Item Set Data Telephone Type and Model Type OHCA Circuit Dyes, Primary-Directory Mer intercom Number -- Model q No ---- Station Name __-------- ICM Group Pickup Group -- Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect q - C None EXT DNone - q Yes, q No q Yes, q No q Yes, q No 6-124 EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Type OHCA dircuit Primacy Directory Number Dyes, Intercom Number -- Station Name ICM Group Pickup Group -- Mdel ONo ONone Next Hunt Station Class of Service q EXT___- Data Line Security ayes, ONo Automatic Callback-Trunk Parallel Connect Dyes, ONo Key Key Type DN-01 PDN ONone c]Yes, q No Number SDN COS DN-03 q q DN-04 llStation.~DN PF Key PF Key Type 1 -. 02 03 03 I 04 05 05 06 06 . 07 08 08 I 09 I 10 11 12 } Station,nDN 01 I 02 07 Station,ODN DSS Key DSS Key Type Number 04 t Night Ring llStation.llDN DN-02 O? Day Ring I 6-125 I Number EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security ‘. :: i Set Data Model Type Dyes, C]No - - - - - - - - - - - - - q ONone EXT ____ Dyes, q ONone No Automatic Callback-Trunk Dyes, ~NO Parallel Connect ayes, q No 6-126 EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model Type Model OHCA Circuit iq Yes, ONo Primacy Directory Number Intercom Number ; - Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk i Parallel Connect 1PF Key 1PF Key Type 1 I 01 I - - - - _--------INone - : [7EXT - - - - - ONone ; q Yes, NO ayes., q No :DYES, q No 1DSS Key 1DSS Key Type 1 Number I 01 02 02 03 I 04 I I 05 I 05 06 06 07 07 _ 1 I 08 09 1 I 08 I 11 I 6-127 Number I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Set Data Model Type q Yes, q N0 Primary Directory Number Intercom Number Station Name ICM Group Pickup Group -- f-J None Next Hunt Station Class of Service TEXT Data Line Security Automatic Callback-Trunk Parallel Connect ayes, UNo ayes, ONo - CNone - Dyes, q No j ’ 6-128 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary-Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect ?F Key PF Key Type 01 Set Data Type Model q Yes, ONo -------------ONone -q EXT ---ONone -q Yes.ONo q Yes. q No Dyes, ONo Number 1DSS Key 1DSS Key Type 1 Number 01 02 02 03 04 05 06 07 08 I 08 . 6-129 EXTENSION-STATION Station Equipment No. F Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Model Type [7Ygs, q No - - - - - __-__----ONone Pickup Group Next Hunt Station q EXT__-- Class of Service Data Line Security Dyes, Parallel [7Yes, - - ONone ONo Automatic Callback-Trunk aYes. ONo Connect ONo 6-130 a EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit ?rirnaq Qirectory. Number Intercom Number Type Model q Yes, q No ----- Station Name ICM Group Pickup Group ------_--- Next Hunt Station Class of Service q EXT---_ -ayes, q No ayes, ONo ayes, q No - Data Line Security Automatic Callback-Trunk Parallel Connect Key 1 Key DN-01 TYPO 1 - /JNone CjNone Number 1 SDN PDN COS 1 q Station,C]DN q tation,nDN Night Ring I astation, q DN DN-02 DN-03 /JStation,q DN DN-04 nstation, q DN DN-05 DN-06 astation, q DN ON-07 /JStation,C)DN DN-08 q DN-09 OStation,C]DN DN-10 q Station,nDN q DN astation, q DN q Station.ODN DN-11 DN-12 PF Key I PF Key Type Number Station, I 1DSS Key 1DSS Key Type I 05 06 07 Day Ring 1 07 I 08 6-131 Number I EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model Type OHCA Circuit Primary Directory Number GYes, Intercom Number -- Station Name ICM Group -------_-- Pickup Group -- Next Hunt Station Class of Service Data Line Security q En ___-q Yes, INo IJYes, IN0 q ]Yes, INo Automatic Callback-Trunk Parallel Connect - 1 - Model INo - - -J None ONone OStation,q DN DN-07 DN-08 j--JStation,q DN DN-09 uStation,ODN DN-lo OStation.q DN DN-11 q DN-12 [ZlStation,ODN PF Key PF Key Type Number 1DSS Key 1DSS Key Type 1 01 01 02 02 03 04 05 06 07 1 08 1 I 09 I I 10 Station.f-JDN 08 I I 11 I 12 6-132 Number I EXTENSION-STATION Station Equipment No. SSi Data Item Telephone Type and Model We Ot-fC;R Circuit IYes, Primary Directory Number - Intercom Number Station Name ICM Group ___------- Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk L Parallel Connect - lhx t. ]No - - [IIh;-0 JEXT ___ayes, ]No 9Yes. ~NO ilYes, ~NO 2 No-te j DSS Ky DSS Key Type Number EXTENSION-STATION Station Equipment No. Item Set Data Model Telephone Type and Model OHCA Circuit Type ayes, Primary Directory Number - - - - - Intercom Number ENO Station Name ICM Group Pickup Group - - - - - - - - - - Next Hunt Station Class of Service q EXT ____ - - ONone - ONone - Data Line Security q Yes, CNO Automatic Callback-Trunk ayes, CNO Parallel Connect Key Key Type DN-01 PDN Dyes, CNO Number SDN COS Day Ring DN-04 q Station,/JD~ q Station,ODN q Station, q DN q Station, q DN D N - 0 5 astation, f’JDN DN-02 DN-03 q q DN-06 DN-07 q DN Station.jJDN f-J%tion, q DN DN-08 q Station, q DN q Station, q DN q Station, q DN q Station,ODN DN-09 DN-10 DN-11 DN-12 J Station, Night Ring . I . . . 12 I I 6-134 . EXTENSION-STATION Station Equipment No. c item Telephone Type ard Model Set Data Model Type OHCA- Circuit Eyes. q ]No Primary Directory Number - Intercom Number - Station Name __-------- ICM Group - Pickup Group Next Hunt Station Class of Service Data LincSecurity Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN - - - - q CEXT ONone - Ncne - Eyes.. q No q Yes, q No Dyes. q No Number SDN COS Day Ring Night Ring aStation, q DN q I q DN astation, q DN q Station.nDN DN-02 DN-03 . DN-04 PF Key PF Key Type Number Station, DSS Key DSS Key Type Number 01 01 02 03 04 i 06 06 07 07 08 t I 09 I I 11 I I 12 I 08 1 I . EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Set Data Type Eyes, q ]No Model Intercom Number Station Name ICM Group Pickup Group ---------- Next Hunt Station EExT Class of Service Data Line Security - Automatic Callback-Trunk Parallel Connect ?F Key PF Key Type -- 0 None ONone - ayes, OF!0 Eyes, ~NO I?Yes, q ]No Number DSS Key DSS Key Type Number 01 01 02 03 04 05 I- 06 I---- 08 6-136 I I I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name CM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN Set Data Model Type aYes, - - ONo - - ------e-v- ONone q EXT ---- ONone Dyes, q No Dyes, q No q Yes. ONo Number q q q q DN-02 DN-03 DN-04 , Day Ring SDN COS ]Station, q DN Station,QDN Station,ODN Station,uDN DN-06 C]Station,nDN DN-06 OStation,jJDN DN-07 astation, DN-06 q astation,q DN-09 CjStation,ODN DN-10 astation, DN-11 OStation,ODN DN-12 q 6-l 37 DN DN q DN Station, ODN Night Ring EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name CM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Set Data Model TYPO q Yes, q No - - - - _--------- - I-J None q EXT___- ONone - q Yes, q No q Yes, ONo q Yes, q No Key DN-01 DN-02 DN-03 DN-04 DN-05 DN-06 DN-07 DN-08 DN-09 DN-10 DN-11 DN-12 PF Key PF Key Type Number 1DSS Key 1DSS Key Type 1 01 01 02 02 05 04 OS 06 06 I I 07 I 09 10 11 t 12 t 07 08 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name CM Group Pickup Group Next Hunt Station Class of Service Data Line Security Set Data Model We Dyes, - - EN0 - - - --------em 0 None - q EXT__-- ONone - q Yes, CNo Automatic Callback-Trunk ayes, NO Parallel Connect (7Yes, CNo Key Key Type DN-01 PDN Number SDN COS Day Ring DN-02 q q DN-03 f-JGtation,~DN q .q q q q q q q q DN-04 DN-05. DN-06 DN-07 DN-08 DN-09 DN-10 DN-11 DN-12 PF Key PF Key Type Number Night Ring Station,/JDN Station,uDN Station,ODN Station,fJDN q Station, q Station, DN . DN Station,nDN Station.ODN Station,ODN Station,nDN Station, [7DN DSS Key DSS Key Type Number 01 01 02 03 106 06 07 07 08 I 10 I 12 t j-139 I I. EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model Type OHCA Circuit Primary Directory Number aYes, - intercom Number S t a t - i o Model - ~No - - - n N a ICM Group Pickup Group - Next Hunt Station q EXT ---- Class of Service Data Line Security ayes, ~No q Ye.s. CNo Automatic Callback-Trunk Parallel Connect m e C]None [7None q Yes, CNo .. .‘, 6-140 EXTENSION-STATION Station Equipment No. item Telephone Type and Model Set Data Model OHCA Circuit TYPO ayes, Primary Directory Number intercom Number Station Name - - - ------.---- ICM Group Pickup Group - Next Hunt Station q EXT ---- Class of Service Data Line Security - Automatic Callback-Trunk Parallel Connect t2 - - ONo ONone ONone - q Yes, ONo q Yes, NO Dyes, ONo I 6-141 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit. Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Rata Line Security Automatic Callback-Trunk Parallel Connect PF Key PF Key Type Set Data Model Type aYes, q N: - - - - - - - - - - - - - - - None q EXT ONone - - q Yes, q Nr q Yes, ON: ayes, Number ON: 1DSS Key 1DSS Key Type 1 01 02 05 06 67 08 I 12 I 6-142 Number EXTENSION-STATION Station Equipment No. r Set Data Item Telephone Type and Model QHC.A Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect l.kcel Type q ]Yes.ON: - - - - ___------q EXT - - ‘;;ne q - N = n e - q Yes. IJN: q Yes. q Nt q Yes. [7Nz DSS Key Type KevIF’FKevTvDeI 6-143 Number EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model TYF~ OHCA Circuit Primary Directory Number ayes, Model ONo Intercom Number Station Name ICM Group ____------ Pickup Group Next Hunt Station -- Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect q ONone EXT ____ ONone -- q Yes, q No ayes, ONo q Yes, q No 6-144 EXTENSION-STATION Station Equipment No. Item Telephqne Type and Model WA-cirti Primary Directory Number Intercom Number Station Name CM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Set Data Model Type ayes.,q No _--_-----__-OEXT - C]None ---_ ONone q Yes, ONo ayes, q No q Yes, q No / 6-145 EXTENSION-STATION Sxtion Equipment No. Item Set Data islephone Type and Model CYCA Circuit P rimaq Directory Number Itiercom Number Tpe Eyes, Model INo Station Name - - - ___------- CM Group - Wkup Group Reti Hunt Station - - 0 None CEXT ONone Class of Service Cata Line Security Eyes. ~NO Automatic Callback-Trunk Eyes, ~No Paralkl Connect q Yes, ~NO 1 Key 1 Key Type 1 Numbs 1 SDN DN-04 q q q q C-N-05 fJStation, fJDN EN-01 PDN DN-02 DN-03 q Station,nDN Station,ODN IlStation. I-lDN q q q IN11 w-12 05 05 ! 06 06 07 07 lo8 08 I 09 10 11 I 12 I Station,fJDN Station, q DN Station. fJDN Station,ODN jStation, q DN Station.DON 1DSS Key 1DSS Key Type I Number I 6-146 Night Ring I DN DN-09 w-10 , Station, DN-08 DN-07 Day Ring 1 Station.nDN q q q GN-C6 *VI-. COS 1 Number EXTENSION-STATION Station Equipmen: No. Item Telephone Type ana Inode 0HC.A Circuit Primary Directory FJumber Set Data Type Dyes, q Model No Intercom Number Station Name ICM Group __-------- Pickup Group - Next Hunt Station Class of Service q EXT ---- Data Line Security Automatic Callback-Trunk Parallel Connect Dyes, - - ONone ONone ONo [7Yes, q No [7Yes, q No , ON-09 q q ON-10 j-J3tation,ODN ON-1 1 ON-12 q Station.nDN loStation, q DN 1 ON-08 PF Key PF Key Type I 01 I Number Station,C]DN Station, q ]DN Number 1DSS Key 1DSS Key Type / I 01 02 02 03 03 04 04 05 06 06 07 07 I 08 I ci3 09 10 11 6-147 ._ EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Sration Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Set Data Type Model q Yes, CNo ----___----_-ONone -:1NOE q EXT ----q Yes, CNo ayes, ENo ayes, CNo 3 6-148 EXTENSION-STATION Station Equipment No. item Set Data Telephone Type and Model Type OHCA Circuit Primary Directory Number Intercom Number IYes. Station Name ICM Group Model ON0 - - - __-------- I - - Pickup Group Next Hunt Station E None q EXT___- Class of Service Data Line Security - ONone - q Yes, ONo Automatic Callback-Trunk Dyes, ONo Parallel Connect ayes.. q No 1PFKey 1 PFKey Type 1 01 Number I DSS Key DSS Key Type Number 01 02 I 03 I 04 05 05 06 I 07 07 I 08 08 09 11 12 ! I 1 6-149 1 I EXTENSION-STATION Station Equipment No. Item Te!ephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Set Data Model Type q Yes, CNo - - - - - - - - - - - - - - - C]None q EXT_--- Data Line Security Dyes, Automatic Callback-Trunk Parallel Connect q Yes, ENo q Yes, NO ONone ENo Number DN-01 PDN DN-02 1 SDN COS q q Station, Day 1 Ring 1 Night Ring I DN Il]Station,[7DN q q 1DN-03 Station, q DN Station,nDN jJStation,nDN q q q q q q q DN-08 DN-09 1DN-10 DN-11 :3 DN-12 1PF Key I PF Key Type Number q Station, q Station, DN DN Station,uDN Station,nDN q Station, q Station, DN DN Station,ODN 1DSS Key 1DSS Key Type I I I 03 I 04 05 05 06 06 08 09 11 12 6-150 Number I EXTENSION-STATION Station EquiFmer: NC. Item Telephone Type ant Model O.HCA.C.ircuit Set Data Tf>e Eyes. Model C:.s Primary Directory Ncmber I Intercom Number i Station Name ~ICM Group ---------- ~ Pickup Group - Next Hunt Station Class of Service [I: EXT ix N / Data Line Security i Automatic Callback-Trunk j Parallel Connect Key j DN-01 Key Type INone - ryes. CKO CYes. C:io Eyes. DNo o n e Number SDN COS q q PDN /DN-02 Day Ring Station,ODN Station,nDN astation, q DN DN-03 q DN-04 Station,nDN DN-05 f-JStation,ODN DN-06 q Station,nDN astation, q DN DN-07 q q q q q ON-08 DN-09 DN-10 DN-11 DN-12 6-151 .Station,uDN Station, [7DN q Station, q Station, DN DN Station.ODN Night Ring EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model We OHCA Circuit Primary Directory Number ayes, intercom Number -- Station Name ICM Group Pickup Group ----------- ONone Next Hunt Station ~I~ExT _ _ Class of Service Data Line Security a y e s , GNo ayes, q No Automatic Callback-Trunk Parallel Connect IT Key PF Key Type Model q NO ---- _ _ ONone q Yes. GNo Number DSS Key DSS Key Type Number 01 O? 1 06 1 I 07 I I 08 09 I 10 I 11 12 6-152 EXTENSION-STATION Station Equipment No. rI- Item Telephone Type and Model OHCA Circuit Primary Directory Number Model Type aYes, - - nNo - - Intercom Number Station Name ----e---e- KM Group Pickup Group - Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect PF Key 1PF Key Type 1 Set Data 0 None o q EXT i-J N - - n q Yes, q No q Yes, ONo q Yes, q No Number 6-153 e EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Model Type aYes, ONo Primary Directory Number Intercom Number Station Name CM Group -_---__--- Pickup Group Next Hunt Station -- 0 None q ]En---_ Class of Service Data Line Security ONone -- Automatic Callback-Trunk Parallel Connect OYes, q No C]Yes, q No q Yes, q No 1 SDN COS 1 Day Ring I Night Ring DN-02 q q DN-11 /-JStation, q DN DN-12 ~Station, DN-01 PDN . we I Number Station, Station, q q q DN DN DN DSS Key IDSS Key Type 1 6-154 Number EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model OHCA Circuit Primary Directory Number Tw Model q Yes, q No Intercom Number Station Name ICM Group ---------- Pickup Group Next Hunt Station - Class of Service Data Line Securiiy Automatic Callback-Trunk Parallel Connect - C]None q EXT--__ q ]None -- q Yes, q No ayes, q No aYes, q No 6-155 EXTENSION-STATION Station Equipment No. kern Telephone Type and Model Set Data Model OHCA Circdil Type aYes. q Primary Directory Number intercom Number Station Name - - - __-------- ICM Group - Pickup Grccrp Next Hunt Station Class of Service No ONone q EXT_-__ Data Line Securiiy aYes, q Automatic Callback-Trunk Parallel Connect aYes, ONone No ayes, q No ONo SDN COS Number 1PF Kev 1PF Kev Tvoe 1 Number 1 I DSS Key DSS Key Type 01 I I 02 I 02 I 03 I 03 04 04 05 05 06 06 I 09 I 10 I I Number 07 08 08 - Night Ring 01 I I 07 I Day Ring 1 I I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic-Catltsack~Trunk Parallel Connect Set Data Model Type Dyes, - - ONo - - _---e----w - ONone q EXT ---- ONone - q Yes, q No ayes, q No q Yes, q No Key DN-01 DN-02 DN-03 DN-04 DN-05 DN-06 DN-07 DN-08 DN-09 DN-10 DN-11 DN-12 DSS Key DSS Key Type 01 02 03 04 05 06 07 08 6-157 Number EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Type OYes, Intercom Number ___------- Station Name ICM Group Pickup Group Next Hunt Station Class of Service - - Model ONo - - - ONone q EXT ---- Data Line Security Automatic Callback-Trunk c]Yes, q ayes, q Parallel Dyes, Connect Key Key Type DN-01 PDN ONone No No ONo Number q Day Ring Night Ring Statican.ODN} /JStahon, q DN 1 DN-02 ON-03 1 ICJStarion.uDN q q DN-11 ON-12 PF Key 1PF Key Type 1 01 Number 01 I 03 I 04 05 06 07 08 9 11 12 6-156 1 1 I Station.nDN Station,nDN DSS Key DSS Key Type 02 0 SDNCOS 1 I Number EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Type Eyes, Primary Directory Number -_-- Intercom Number Station Name CM Group - - - A - L - - - ONone - Pickup Group Next Hunt Station Model ~NO EEXT ONone Class of Service Data Line Security Automatic CBilback-Trunk Dyes, JNo Parallel Dyes, JNo Connect PF Key. PF Key Type q ]YE., ]NO Number 1DSS Key 1DSS Key Type 1 01 05 06 06 I 07 07 II 08 08 I 09 I 6-159 I Number EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Type ZYes,q Model N: - - - __-------- Pickup Group Next Hunt Station - - 1 None =EXT ONone Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Dyes, ON: q Yes, q Nc q Yes, ON: Number I SDN COS Day Ring Night Ring I I DN-02 loStation. iDN N I I ! DN-07 l&tation. ODN N PFKey PF Key Type a1 02 03 1DSS Key 1DSS Key Type 1 Numb& I I I 02 I 03 1 OA 04 05 05 t 06 1 07 Number I 08 09 10 11 12 6-160 06 I I 1 I b8 I EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model OHCACircuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Type Model Eyes, ~NO - - - __-------- - C None q EXT ---- Data Line Securiiy C]Yes, ?No Automatic Callback-Trunk ayes, ~No Parallel Connect aYes, ~NO ENone EXTENSION-STATION Station Equipment No. Set Data Telephone Type and Model We OHCA‘Circui? Primary Directory Number aYes, Intercom Number Station Name ICM Group -- Pickup Group -- Next Hunt Station Class of Service q EXT ---- Data Line Security Automatic Callback-Trunk Parallel Connect PF Key 1PF Key Type ) 0’ I 02 I 03 I Model ONo ---- /-J None ONone -- Dyes, q No q Yes, UNo Dyes, q No Number DSS Key DSS Key Type Number 01 04 I 05 I 06 07 08 6-l 62 + EXTENSION-STATION Station Equipment No. Set Data item Telephone Type and Model QHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Modol Type Eyes, q No m------e-- -- CjNone Next Hunt Station Class of Service i?EXT --__ Data Line Security Automatic Callback-Trunk Parallel Connect @Yes, q No Eyes, q No Dyes, q No Key Type Number PDN q NDne -- Day Ring j SDNCOS Night Riq /JStation,/JDN 1DN-02 jIStation,uDN 1DN-03 /gStation,[7DN FJStation, q DN 1 iJStation.nDN /gStation,C]DN /IStation,oDN /?JSSfation. q (. DN IFJStation.ODN 1DN-10 igStation.nDN DN-11 /gStation,ODN DN-12 t lj7Station.ODN 1 I : EXTENSION-STATION Station Equipment No. kern Telephor:s Set Data Type and Model OHCA C *suit Primary S rectory Number Model Type q ]No ---- Dyes, intercom Umber Station &me CM GroL3 - Pickup G->up Next Hur: Station Class of Service -- ONone EEXT - Data Lin5 Security Automat;; Callback-Trunk Parallel Connect - q No [?Yes. q No ayes, q No @Yes, e PF Key PF Key Type 1 Number 01 ONone DSS Key DSS 1 01 06 I 07 I I 06 I b 07 6-164 Key Type Number EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Model Type q Yes, q ]No OHCA &wit Primary Directory Number Intercom Number ---_ - Station Name ICM Group Pickup Group ------____ - Next Hunt Station Class of Service q EXT--__ Data Line Security q Yes, q No Dyes, q NO q Yes, q No - - Automatic Callback-Trunk Parallel Connect Key Key Type / - 0 None ONone - Number ( SDN COS q q DN-08 DN-09 Station, q Day Zng Night Ring DN Station.C]DN astation,q DN DN-10 q q DN-11 DN-12 Station,nDN Station, q DN DSS Key DSS Key Type 01 PF Key 1 PF- Key Type 1 01 Number 02 05 06 38 06 , 1 I 07 I 08 I 1 . EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Type OHCA Circuit Primary Directory Number aYes, Intercom Number - Station Name ICM Group Pickup Group - - - - - - - - - ONone q IEXT ____ ONone Next Hunt Station Class of Service Data Line Securiiy Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN - - Model - - - - - Dyes, q q ONo ‘fes, q UNo NO ]Yes, (7No Number SDN COS / DN-02 q q DN-03 1 lnStation,CDN q DN-04 Station,EDN 1 / Station,CDN 1 [IIStation.CDN! ‘DN-06 nStation,rDN D N - 0 7 astation, DN-08 q DN-09 rJStation, CDN DN-10 @tation, CDN DN-11 aStation, CDN DN-12 astation, CDN 1 CDN 1 .. Station,CDN ( DSS Key [DSS Kq Type 01 Night Ring Station.CDN 1 DN-05 1PF Key 1PF Key Type 1 Day Ring Number 1 04 05 05 06 06 07 07 08 08 09 10 11 6-l 66 1 1 EXTENSION-STATION Staiior: Equipment No. Item Telephc 78 Type and Model Set Data Model Type CifCA Circuit q Yes, ONo Primar,. Directory Number - Imerco;7 Number - Station Yame __-------- ICM Gr=,up - P&kup cjroup - Rext HLnt Station q EXT -_-- CIass c’ Service Data L1,?e Security Automzzic Callback-Trunk Parallei Connect Key Key Type DN-01 PDN - - - - - - ZNone 0 None - q Yes, ONo Dyes, q No q Yes, q No Number / SDN COS //-JStation,nDN q q @tation, q DN-02 DN-03 6-167 Q Day Ring station, DN DN Night Ring EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model OHCA Circuit Primary Directory Number We aYes. q No Model Intercom Number Station Name - - - ----v----e ICM Group Pickup Group - Next Hunt Station Class of Service q EXT---_ - ONone ONone - q Yes.ONo Data Line Securiiy Automatic Callback-Trunk Dyes. NO Parallel Connect aYes. ONo 12 1 I 1 6-l 68 EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model I Type OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group - - - - - - - - - - - - Z]EXT - Class of Service Data Line Security - Automatic Callback-Trunk Parallel Connect DN-01 No - Next Hunt Station I IYes.q tAode I @Nme - - - JNone - Z]Yes. q No IYes. q No 2Yes. q No Nmber Day Ring SDN COS PDN CStation, 6-169 q DN Night Ring EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Model Type OHCA Circuit aYes, q No Primary Directory Number - - Intercom Number - Station Name ___------- ICM Group - Pickup Group - Next Hunt Station q EXT ---- Class of Service Dyes, q Data Line Security Automatic Callback-Trunk ..Parallel Connect Key Key Type DN-01 PDN - - - 0 None ONone No q Yes, q No Dyes, q No SDN COS Number q Night Ring ]Station,ODN aStation, q DN DN-02 q q q q q q q q DN-OS DN-04 DN-05 -DN-06 xii-07 DN-08 DN-09 q Station, q Station, DN-11 DN-12 1PF Key 1PF Key Type 1 Number DN DN Station,ODN Station,j-JDN q Station, q Station. DN Station, DN DN DN DSS Key DSS Key Type 01 01 02 02 03 03 04 04 05 05 06 06 07 I 08 08 09 10 11 12 6-170 t DN Station,ODN q astation, q q Station, q DN-10 1'07 Day Ring / Number EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Set Data Model Type OYes, - - INo - - - ---_------ 0 None q EXT---_ - ONone - q Yes, ZNo Dyes, INo aYes. ~NO ) DN-01 SDN COS 1 Night Ring astation, q DN PDN DN-02 OStation,nDN DN-03 q Station,ODN DN-04 fJStation.nDN DN-05 nStation,ODN DN-06 q DN-07 DStation,uDN DN-08 q DN-09 C]Station,ODN DN-10 q DN-11 OStation,ODN DN-12 q PF Key- /PF Key Type Day Ring Number Station,ODN Station, q DN tation,nDN Station,ODN I 1DSS Key 1DSS Key Type 1 Number I I 05 06 07 08 I 10 I 11 12 6-171 _ EXTENSION-STATION Station Equipment No. r Item Telephone Type and Model OHCA‘Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Set Data Model Type Dyes, - - ONo - - ___------- 0 None q EXT_--- ONone - q Yes, q No q Yes. q No q Yes, ~NO bN-08 iStati0n.c DN-09 DN-10 q q q q DN-11 DN-12 1 PF Key PF Key Type 01 Station,ODN Station,nDN Station, q DN Station.ODN [ DSS Key 1DSS Key Type 1 Number Number 1 01 02 I I 05 06 07 ’ 08 08 09 r 10 I 1 I . 6-172 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model Set Data Model Type OHCA Circuit q Yes, q No Primary Directory Number - Intercom Number - Station Name -------v-P ICM Group - Pickup Group - Next Hunt Station q EXT_-__ Class of Service Dyes, Data Line Security Automatic Callback-Trunk Parallel Connect - - - - - ONone ONone ONo q Yes, q No q Yes, q No q q q q DN-09 DN-10 DN-11 DN-12 PF Kay. PF Key Type Number 01 02 03 04 05 .06 07 0 8 09 6-l 73 Station,ODN Station,ODN Station, q ]DN Station,nDN EXTENSION-STATION Equipment No. Station Item Set Data Telephone Type and Model Model Type OHCA Circuit Ryes, q No Primary Directory Number - - Intercom Number - Station Name ____------ ICM Group - Pickup Group - Next Hunt Station q EXT__-_ Class of Service aYes, Data Line Securiiy Automatic Callback-Trunk 1 Key 1 Key Type 1 DN-01 . - . I 0 None - ayes, aYes, q Paralfel Connect I - ONone UNo ONo No Number 1 SDN I PDN Day Ring Night Ring lostation, CDN 1 -DN-02 c COS : [7Station, CDN j DN-03 q DN-04 [7Station,EDN 1 Station. CDN / DN-06 q q DN-07 [7Station, EDN 1 DN-06 ]Station,CDN 1 Station, CDN 1 DN-11 q q q q DN-12 ,OStation, EON 1 DN-08 DN-09 DN-10 1PF Key 1PF Key Type 1 . Station.LDN Station,CDN Station.CjDN Station. C;DN 1 I DSS Key DSS Key Type Number Number 01 02 02 I 03 03 I 04 04 05 05 iOs--- I I ._ 06 07 08 I EXTENSION-STATION Station Equipment No. Item Set Data Teiephone Type 2nd Model Type OHCA C‘ircuit CYes, Model flNo Primary Directory Number Intercom Number Station Name ICM Group - Pickup Group -- ONone Next Hunt Station CEXT _ _ Class of Service -- Data Line Security Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN _ _ ONone ryes, q No ryes, ~NO ryes, ONo Number 1 SDN rStation,ODN DN-02 aStation,CjDN DN-03 mStation,ODN DN-04 q DN-05 mStation,nDN [PF Key 1 PF Key Type 1 Day Ring COS 1 1 Station,lJDN Number 01 02 I 03 I 04 04 05 05 06 06 07 ! 08 I 1 08 I 10 I I 11 I 1 12 1 6-175 Night Ring 1 I EXTENSION-STATION Station Equipment No. item Telephone Type and Model OHCA Circuit Primary Directory Number Set Data TYPO q Ye.s.JNo ---- Intercom Number Station Name -- ICM Group - Pickup Group Next Hunt Station Class of Service -- Data Line Security Automatic Callback-Trunk Parallel Connect Modal ONone q EXT-_--q Yes, JNo ayes, ~NO q Yes, ~NO ONone 6-176 EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Type OHCA Circuit lJYe3. c ‘u: Primary Directory Number - - - ___------- Intercom Number Station Name ICM Group Pickup Group F.ldel - Next Hunt Station 1 Ncne 0-T -_-- Class of Service Data Line Security ayes, Automatic Callback-Trunk IYes, Parallel Connect /-JYes, Key Key Type DN-01 PDN r]None C’NJ 1%: C’t3 SDN Number / CStatic-. COS I 7DN : DN-02 CStatio-. IDN DN-03 CStatio-. IDN j DN-04 FStatic-. 1DN : DN-05 CStatio-.r]DN i DN-06 T?Static:.lDN DN-07 EStaticr. IDN i DN-08 EStatior.]DN DN-09 astation. JDN 1 DN-10 j-JStatior. JDN DN-11 DStatioc. DN-12 q 12 6-l 77 -Qb JDN Statior.JDN / / Day Ring Night Ring EXTENSION-STATION Station Equipment No. I- Set Data Item Telephone Type and Model OHCA Circuit Type Dyes, Primary Directory Number - Intercom Number Station Name ICM Group - - - - - ONone q EXT ---- Class of Service Data Line Security Automatic Callback-Trunk Connect I Key I I Key we DN-01 PDN UNo __-------- Pickup Group Next Hunt Station Parallel - Model II ayes, q ONone No q No q Yes, q No ayes, Number 3lJN c;U3 uay Rinf q Station,~DN IN 6-l 78 Night Ring EXTENSION-STATION S:ation Equipment No. Item Telephone Type and Model Model Type OHCA Circuit q Ye.s. Primary Directory Number ---_ Intercom Number - Station Name - ICM Group - Pickup Group - Next Hunt Station q EXT--__ Class of Set-vice ayes, Data Line Security 1 Set Data q No - - - - - - - - - 0 None - CNone ONo Automatic Callback-Trunk ayes, ONo Parallel Connect Key DN-01 q Yes, q No Key Type / I PDN Number Day Ring SDN COS rStation,nDN CStation,q DN DN-02 CStation,q DN DN-03 3 PFKey PFKeyType Number DSS Key DSS Key Type Number 01 01 02 03 04 I I 07 Night Ring - 08 09 10 11 12 6-l 79 +a EXTENSION-STATION Station Equipment No. Item Telephone T y p e and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Key DN-01 DN-02 Key Type Set Data Type Dyes,q - - - EAcxel ]Nc - - - - - - - - - - - C’ ;srle E None q EXT ---- - q Yes, q Nc q yes, q Nc q Yes, q Nc i Number / SDN COS / P D N InStation, [7DN 1 inStation.f-JDN DN-03 DN-04 DN-05 /OStation, /JDN DN-06 DN-07 DN-08 /!-JStation,CjDN DN-09 )-JStation.ODN inStation.ODN IilStation.llDN lC]Station.nDN inStation,nDN Ii-JStation. DN-10 DN-11 3 05 08 07 08 09 11 12 ]DN /OStation.ODN I jC]Station. q DN DN-12 PF Key PF Key Type 01 02 03 04 q Number I i / 1 J I j I / I 1 I 6-180 Day Ring Night Ring EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circui? Primary Directory Number Type aYes, q - Station Name _---e----v ICM Group Pickup Group - Next Hunt Station q EXT ---- Class of Service IYes,q Data Line Security Automatic Callback-Trunk Parallel Connect - No Intercom Number - - Model - - - ONone ONone No ayes, q No q Yes, [7No 6-181 * EXTENSION-STATION Station Equipment No item Telephone Type and Model OHCA Circuit --. Primary Directory Number intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security. Automatic Callback-Trunk Parallel Connect Set Data ~4tcdEl Typ q YSS. -JNo - - - - - -----__-__ - - C R3ne q EXT ---- q Nc-e - q Yer,JNo q Yes.]No q Yts, ~NO 6-182 43 EXTENSION-STATION Station Equipment No. r Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line SecurityAutomatic Callback-Trunk Parallel Connect Set Data Model Type q Yes, NO -_-____------ - ONone q EXT__-- ONone - q Yes, q No q Yes, q No Dyes, q No 6-183 EXTENSION-STATION Station Equipment No. item Telephone Type and Model Set Data Model OHCA Circuit Type aYes, q No Primary Directory Number - - Intercom Number - Station Name - - - - - - - - - - ICM Group - Pickup Group - Next Hunt Station q EXT__-- Class of Service - Da& Line Security Automatic - - - PF Key PF Key Type q ]None - q Yes, [7No Callback-Trunk Dyes, Parallel Connect 0 None UNo q ]Yes, (7No J 1DSS Key 1DSS Key Type 1 Number 01 01 02 02 1 08 1 I 09 I I 10 I I 11 I I 12 I I 6-184 08 Number EXTENSION-STATION S:s- ;- fquic-snt NC Set Data Tt +;-,z -,z Tyz.5 2nd Moos Type c-3: IYes, : :cuit F- -2’: Iirec;:-f Number - In.+-::-- - Numr.2: Model q No - - - - S:::sr ‘.ame - - - - - - - - - - ic 1.1 s*:t.Jp - F I::. -2 3oup -- he:: - -11 sta:,r7 ?EXT __-- ONone C.rss ;- Servir* II]Yes,q ]No C ; : ;, -3 Set- - :y Ait 3 7;;:c C a l ONone rxk-Trunk IYes, ONo Number 1 SDN COS 1 Day loStation.ODN (OStation. Dk-3 q 1 DN 1 loStation,nDN q q Dh-:.Z D’V-:5 Night Ring Ring 1 I Station,nDN I Station,ODN I I I OStation,nDN q Station.uDN [IIStation, q DN nStation.nDN q Station,~DN q Station, q DN q Station.~DN PF <(ay ’ PF Key Type -. - DSS Key DSS Key Type Number Number 01 02 22 06 07 I 6-185 08 1 I I EXTENSION-STATION Station Equipment No. Set Data item Telephone Type and Model Type OHCACirwit ayes, Primary Directory Number Intercom Number ---- Station Name ICM Group P&up Group ___------- Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect 1 c Key 1 Key Type 1 DN-01 PDN Model / IJk -- q 3 None EXT [? N o - - - n e q Yes, q K3 q Yes, Ok:= Dyes, iJr;S Number / SDN COS 1 1 JStation,nDN DN-02 DN-03 /mStattin. (7DN /OStation,ODN DN-04 1 jJStation. q DN DN-11 DN-12 lOStation,uDN ll-&tation,flDN DSS Key DSS Key Type 01 02 03 04 05 06 07 08 Day Ring Night Ring Number EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data LineSecurity Automatic Callback-Trunk Parallel Connect Set Data Mcxel Type ayes, q No 1 -__--_------ ONone q EXT niba - - q Yes, q No q Yes, q No q Yes, q No Number DN-01 1 SDN PDN EStation, COS 1 Day Ring q 5 DN DN-02 EStation,nDN DN-03 ~staion, q DN DN-04 CStation, DN DIMI5 L!Station,nDN DN-06 C;Station,nDN DN-07 uStation,ODN DN-06 ~Station,fJDN DN-09 [?Station,C]DN DN-10 nStation,ODN DN-11 US&&ion. fJDN DN-12 [7Station,uDN 6-187 q 1 Night Ring EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Directory Number Primary Intercom Number Station Name I Set Data Model TYPO q Yes, EN3 - - - - - __-------- CM Group - Pickup Group - Next Hunt Station q EXT--_- Class of Service Data Line Security - - INone ONone - ’q Yes, NO Automatic Callback-Trunk aYes, EN3 Parallel Connect aYes, GNo Key Key Type DN-01 PDN Number SDN COS q q DN-02 Station, q Day Ring 1 DN DN-06 q q q DN-07 [7Station. BON DN-04 DN-06 q q q q q DN-08’ DN-09 DN-10 DN-11 DN-12 1PF Key 1PF Key Type 1 I 01 1 I I I 01 02 03 03 04 04 05 05 06 06 07 07 1 , Sration,nDN Station, q I DN Station.nDN Station,mDN Station,uDN Station,nDN q Station, q Station, DN ]DN 1DSS Kev 1DSS Kev Tvpe 1 Number 02 08 1 Station,ODN OfStation, q DN DN-03 I 6-188 08 Night Ring Number I I I I I I 1 EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Type ayes. Intercom Number - ___------- Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data- Line Security Automatic Callback-Trunk Parallel Connect Model C)U: _--- q EXT C. - z None None - q Yes. CL3 q Yes, CQ aYes. CL3 6-189 EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model We OHCA Circuit Primary Directory Number ayes, Model UNo Intercom Number Station Name ICM Group Pickup Group ____------ Next Hunt Station Class of Service Data Line Security q ]EXT_--- Automatic Callback-Trunk Parallel Connect __ F Key DN-01 Key Type 1 I -- ONone ONone -- ayes, q No Dyes, q No aYes, ONo Number SDN COS q DN q Station, q DN q Station, q DN q Station.nDN q Station,ODN q Station,/-JDN q Station, q DN astation,q DN q Station, q DN q Station,~DN q Station, q DN flStation, q DN PDN @tation, DN-02 DN-03 DN-04 DN-05 DN-06 DN-07 DN-08 DN-09 DN-10 DN-11 DN-12 PF Key PF Key Type 01 02 Night Ring Day Ring Number I . DSS Key DSS Key Type . Number 01 I 02 03 03 I 04 I 04 I 05 I 1 06 1 05 06 07 07 08 08 09 10 11 12 6-190 I I EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model C)HCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data- LineSew.wity Automatic Callback-Trunk Parallel Connect 1PF Key 1PF Key Type 1 Model Type ayes, q No ---- I ------------ ONone q EXT__-_ ONone q Yes, q No q ]Yes, q No q Yes, q ]No Number DSS Key DSS Key Type 01 01 02 06 07 09 10 11 I 12 I 6-191 Number EXTENSION-STATION Station Equipment NC. Set Data Item Telephone Type and MOE OHCA Circuit Primary Directory NumbeIntercom Number I ! Station Name /ICM Group j Class of Service j Data Line Security ON0 - - ----m--e-- / gYes, / Automatic Callback-Trun+ i Parallel Connect DN-01 - Model ENone :j TEXT ONone I - - Pickup Group INext Hunt Station 1 Kw 1 Key _ iwe . Type i IYes. j- - - 1 ONo / aYes, q No j gYes, ONo Number 1 SDN q q q PDN DN-02 DN-03 DN-04 1 1 t q q q q q q q q DN-05 DN-07 DN-08 DN-09 DN-10 DN-11 DN-12 T Pi: Key PF Key Type Number 01 02 02 03 03 04 04 05 U6 07 6-192 ail Ring 1 Night Ring 1 - Station,C]DN Station,nDN 1 Station,ODN Station,aDN Station,nDN tation,aDN StationJJDN StationJ-JDN Station.ODN Station, q DN DSS Key DSS Key Type 01 Day Station,uDN loStation,ODN DN-06 3 COS Number EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect 1 Key 1 Key We 1 DN-01 Set Data Model Type Dyes, q No _--__----__-C]EXT C]None -__- ONone OYes, q No OY~S, q NO ayes, q No Number 1 SDN COS 1 PDN Ring 1 Night Ring I ~Station,ODN DN-02 aStation, QDN DN-03 q f-JStation, q DN DN-05 nStation,nDN DN-08 q tation,~DN DN-07 ~Station.~DN q q q DN-08 DN-09 DN-10 I Station,DDN DN-04 { i . Station,nDN I Station,ODN Station,ODN DStation,q DN DN-11 q DN-12 PF Key PF Key Type Day Number Station,nDN DSS Key DSS Key Type 01 01 05 06 07 08 I 12 I 6-193 Number EXTENSION-STATION Station Equipment No. Set 3ata Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Type mYas, Meet ONo - - - ____-----ONone q EXT C]Ncne Pickup Group Next Hunt Station Class of Service Data Line Security .Automatic Callback-Trunk q Ye.s. ONo Parallel q Yes, q No Connect - - [7Yes, ONo Number I I SDN COS I - I DN-03 1 IC]Station.EDN N I DN-06 1 I 1 I l~Station,~DN N , I I DN-08 /[?Station,iDN N PF Key PF Key Type I 01 I 1DSS Key 1DSS Key Type 1 Number I 01 i I 02 I 1 06 t 08 1 07 08 09 I 11 I I Number EXTENSION-STATION Stat;,-n Equipme-it No. Item Set Data Teleshone Type a-,3 Model Model Type OHCA Circuit- aYes, q NO Primary Directory Kumber ---- Intercom Number Station Name ---------- ICM Group - Pickup Group - Next iiunt Station q EXT ____ Class of Service - ONone ONone -- Oata Line Security Automatic Callback-Trunk Parallel Connect Dyes, q NO OYes, q No ayes, q No Key 1 Key Type / DN-Zl 1 SDN COS 1 PDN astation. q DN DN-C3 q DN-W Q3tation.nDN Diws- q Station,ODN Station,[7DN astation, q DN I astation, q DN 3N-07 q Station,~DN q Station,ODN astation, q DN astation, q DN q Station,[rlDN DN-08 DN-09 DN-10 DN-11 DN-12 DSS Key DSS Key Type i PF Key [ PF Key Typs 1 01 I 01 ; 02 05 1 06 1 f 07 I 1 Night /JStation,nDN DN-M DN-06 Day Ring 06 I 07 08 08 09 10 11 12 6-195 It Number Ring 1 EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model Model - OHCA Circuit Type [7iYes, q Primary Directory Number -_-- Intercom Number - Station Name ____------ ICM Group - Pickup Group - Next Hunt Station q EXT_--- Class of Service Data--Line Security Automatic Callback-Trunk I Key Type PDN - C None - UYes, ONone UNo aYes, q No q Yes, q No Parallel Connect Key DN-01 No - ( SDN COS Number Day Ring InStation,nDN I I 1 DN-02 /EStation. EDN DN-03 InStation,[7DI N DN-04 &tation,nDN q q q q q q q DN-05 DN-06 DN-07 DN-08 DN-09 Night Ring I Station,iJDN Station.ODN Station, q DN Station, ODN Station,nDN q DN Station, q DN astation, q ]DN DN-10 DN-11 DN-12 J Number Station, DSS Key DSS Key Type 01 01 02 02 03 03 05 1 ,06 I 07 I 1 08 t 06 6-196 1 Number EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Set Data Model Type ~ IYes, ~NO Primary Directory Number i - - - Intercom Number ( T-Station Name I --_-__---I ICM Group Pickup Group Next Hunt Station Class of Service ONone ’ ]EXT ONone - - Data Line Security 1 JYes, JNo Automatic Callback-Trunk / 7Yes, JNo Parallel Connect / IYes, ]No I ON-01 PDN SDNCOS i q q Station, q q Station, q astation, DN-02 DN-03 . DN-04 1 Night Ring 1 DN1 DN i DN 1 /JStation,ODN 1 DN-06 q q DN-07 ilStation,llDN 1 DN-05 Station,C]DN i Station, DN-09 q q DN-10 [7Station, DN-08 Station, q q DN-12 DN 1 DN 1 Station,ODN q astation, q q Station, q DN-11 PF Key PF Key Type Day Ring DN DN DN 1 DSS Key 1DSS Key Type 1 Number 01 01 02 03 04 02 I 03 I I 08 09 10 6-197 a 06 I Number I EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model OHCA CTrcuit Primary Directory Number Model Type ayes, q NO Intercom Number Station Name ICM Group ____---_-- Pickup Group Next Hunt Station -- ONone !JExT _ _ Class of Service Data-Line -Security -Dyes, q No Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN - q _ _ ONone Ye.s. ONo aYes, ONo SDN COS Number q DN-04 (7Station, DW05 astation, DN-06 q Station, Station, t DN-08 1 InStation. 1DN-09 1 jOStation, q q DN-11 DN-12 05 05 06 1 I 06 07 07 08 08 09 10 , 11 Station, Station, i Key Type Number I 1 Night Ring loStation, DN-03 1PF Key 1PF Key Type 1 Day Rin; I 6-198 Number EXTENSION-STATION Station Equipment No Item Telephone Type and Model OHCA Circuit Primary Directory Number Set Data Type Dyes, q I Model I No ---- / Intercom Number Station Name ICM Group - Pickup Group -- ONone Next Hunt Station Class of Service Data LineSecusity !IExT _ Dyes, ~NO Automatic Callback-Trunk Parallel Connect Dyes, ONo PF Key PF Key Type 1 ayes,q _ _ _ ONone No 1DSS Key I DSS Key Type 1 Number I 01 03 04 I 02 02 I 01 I I 03 04 05 05 06 06 07 07 08 6-199 I Number EXTENSION-STATION uipment NCL em Set Data Type and Model Jit ectory Model Type q Yes, C]No Number - Jmber ne - - - - - I L--------DNone JP - station rvice jq EXT ____ iecurity 1 Dyes, Callback-Trunk IDyes. q NO inect / ayes, j- - ONone DNo ONo __1 It Ring 12 1 6-238 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model Set Data Model OHCA Circuit Type TYes. Primary Directory Number --_- Intercom Number - Station Name --_------- ICM Group - Pickup Group ONone _‘ExT ONone Next Hunt Station Class of Service - Data Line Security JYes. q Automatic Callback-Trunk ,lYes. Parallel Connect 2Yes. q Key Key Type DN-01 PDN ~NO No [ZINo No Number SDN COS Day Ring Night Ring llStation.llDN DN-03 q q DN-04 nStation.flDN DN-02 Station,nDN Station,nDN q Station,nDN q Station,[7DN q jStation, q DN q jStation,uDN q Station,~DN q Station, q DN OStation, q DN q Station, q DN DN-OS DN-06 DN-07 DN-08 DN-09 DN-10 DN-11 DN-12 Number I 1DSS Key IDSS Key Type I I 04 I 05 06 06 07 6-239 Number I EXTENSION-STATION Equipment No. Station Item Set Data Telephone Type and Model Model OHCA Circuit Type aYes. q Primary Directory Number _--- intercom Number Station Name - ICM Group - Pickup - No - __-------- Group ONone - Next Hunt Station q EXT_--- Class of Service - - Data Line Security Ryes., Automatic Callback-Trunk Dyes. Parallel Connect ayes, Key Key DN-01 ONone ONo ~NO q No Number Type 1 SDN q q q PDN DN-02 DN-03 [ PF Key 1PF Key Type 1 COS 1 Day Ring ]Station,ODN Station,nDN 01 01 I I ! I 04 05 . 06 06 07 07 I . 12 I 6-240 08 1 1 I 02 103 Nioht Rina w I Station,ODN 1DSS Key 1DSS Key Type 1 Number - I I 1 I Number 1 EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model T,.De OHCA Circuit C Yes, 1 ‘c Primary Directory Number - - - Intercom Number - - Station Name ___------- ICM Group - Pickup Group ‘done CEXT _--’ Next Hunt Station Class of Service Model CYes, Data.Line Security - a None 1’4 Automatic Callback-Trunk Eyes, I\d Parallel Connect [IYes, 1 ‘a Key T y p e DN-01 DN-02 DN-03 DN-04 PDN Numbs- / SDN COS 1 ICjStation, q DN j I , ‘nStation,/JDN q q DN-05 Station,nDN ]Station,CjDN jJStation,nDN DN-08 q Station. q DN q Station,nDN q Station,~DN DN-09 lnStatbn,ODN DN-06 DN-07 q q DN-10 DN-11 DN-12 6-241 Station,ODN Station,[7DN 1 Day Ring 1 Night Ring 1 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Set Data Mcxiel Type q Yes, q No -_-___------_ - - - ONone Next Hunt Station q EXT__-- Class of Service DatatineSeetxiiy Automatic Catlback-Trunk ayes, Parallel Connect PF Key PF Key Type 01 ONone UNo q Yes, NO q Yes, UNo Number 1 DSS Key 1DSS Key Type 1 01 02 02 03 03 I 06 07 08 6-242 I Number EXTENSION-STATION Staticn Equipmec No. -I-- Item Telephone Type and Model t r3HCA Circuit Primary Directory Number Set Data Type Model q ]No ---_ Dyes. intercom Number -- Station Name ICM Group __-------- Pickup Group Next Hunt Station -- ONone [?EXT __-- Class of Service Data. Line Security - 1 Key 1 Key Type DN-01 - ayes, Automatic Callback-Trunk Parallel Connect [7None ayes, ONo ONo q Yes, q No Number 1 SDN q PDN COS Station,mDN ( DN-02 IJSration, q ]DN DN-03 !-JXation,C]DN DN-05 q q DN-06 OStation,nDN DN-07 nStation.DDN DN-04 q q q q q DN-08 DN-09 DN-10 DN-11 DN-12 PF Key PF Key Type ; Number 01 02 03 04 t 05 06 07 07 08 1. 09 i 08 11 12 6-243 1 q Station, q Stafion, ]DN DN Station,[7DN Station,nDN Station,nDN Station.nDN Station.C]DN Day Ring ; Night Ring 1 EXTENSION-STATION Station Equipment No. item Set Data lb!odel Telephone Type and Model Type OHCA Circuit Primary Directory Number intercom Number Station Name ICM Group Dyes, Pickup Group - Next Hunt Station Class of Service Data Line Security q EXT_-__ Automatic Callback-Trunk Parallel Connect l-Jfes, mtv: ayes, CL2 Cl+2 - - - ---------_ - - - INone ONone - q Yes, Ctc q q q q q q DN-07 DN-08 DN-09 DN-10 DN-11 DN-12 PFKey PFKey T y p e 01 02 02 I Station, q DN Station,nDN q Station, q Station, DN DN ]Station,nDN DSS Key DSS Key Type Number 0 1 I 03 Station,nDN I Number 03 04 04 05 05 06 07 I I 12 I 08 I 6-244 %B ..- EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Type OHCA Circuit [7Yes, Primary Directory Number - Intercom Number - Station Name -------___ ICM Group - Pickup Group - Next Hunt Station q Class of Service Model - ENo - - - INone - - - Automatic Callback-Trunk q Yes, ONo Parallel Connect (7Yes, ayes,q Data- tine Security Key DN-01 I DN-02 Key Type PDN ONone EXT ____ NO ~NO Number 1 I SDN COS 1 I hStation,nDN/ ,1 /OStation,iDN 1 I DN-03 q DN-04 fJStation,aDN q DN q Station, q DN q Station.~DN DN-11 DN-12 1 12 Station, I 6-245 Day Ring - - 1 I II Night Ring EXTENSION-STATION Station Equipment No. r- Set Data Item Telephone Type and Model OHCA Circuit Primary Directory Number intercom Number Station Name CM Group Pickup Group Next Hunt Station Class of Service Data Line Security Modei Type q Yes, C’:o - - - - ___------J None q EXT ,I N o - n - q ]Yes, C!lo A u t o m a t i c Caltback-Trunk Dyes, c?(o Parallel Connect Dyes, EN0 12 1 6-246 e EXTENSION-STATION Station Equ:cme-: ‘Jo. Set Data her-Telephone T) x art: ‘.‘odel Model OHCA Circuii Type aYes, Primary DirecIry t. _ -her - Intercom Nurrzer - Station Name __-------- ICM Group - Pickup Group - Next Hunt StaTion Class of Service - - - - q ONone - IEXT ____ Data Line Sewrity ayes, Automatic Ca!:jack--‘unk q Parallel Connsct ayes, 1 Key 1 Key Twe CNo ONone UNo Yes, @NO ONo Number 1 SDN DN-05 q Station, q fJStation,q q Station, q q Station, q DN-06 IlStation. nDN DN-07 q DN-08 /-JStation,/-JDN DN-09 nstation, [7DN DN-01 q q PDN DN-02 DN-03 DN-04 q q q DN-10 DN-11 DN-12 1 PF Kay 1 PE Key Type Number ]Station, Station, Station, Day COS 1 q q Ring 1 Night Ring 1 DN DN DN DN DN DN . DN Station,/JDN Station,nDN DSS Key DSS Key Type Number 01 01 I 02 I 03 I 04 05 roi 06 08 09 1 08 10 I 11 I I I 07 1 I I 1 l2 I 6-247 I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model Set Data I Model OHCA Circuit Type IYes, ON2 Primary Directory Number - - - Intercom Number - - Station Name - - - - - - - - - - ICM Group - Pickup Group - Next Hunt Station C]EXT __-- [7None Class of Service C]Yes, ONo Data Line Security Automatic Callback-Trunk -Parallel Connect 1 Key 1 Key Type 1 - ZNone - q Yes, q No q Yes, q No Number 1 SDN q q DN-11 DN-12 12 1 I 6-248 COS 1 Station,ODN Station,C)DN Day Ring I Night Ring I EXTENSION-STATION Station Equipment Pi: item Set Data Telephone Type and IJ:bz?l TYPO OHCA Circuit JYes. Primary Directory Numz- - intercom Number - Station Name - - - - - - - - - - ICM Group - Pickup Group 9EXT Next Hunt Station Class of Service I.bdel - Z]No - - - Crkne q Data Line Security mYis. ]No AutornaticCalttrack-Tr,-a. aYes. ~No Parallel Connect JYes. ~No 1 Key / Key Type 1 1 DN-01 1 PDN N o n e NilrnDer 1 SDN COS 1 1 Dw IlYlStation.nDN 1 q q q q DN-02 DN-03 DN-04 Rina 1 Nbht Rina 1 I I Station,nDN Station, q DN I]Station,nDN q DN OStation,q ]DN q Station, q DN q ]Station, q DN q Station,nDN q Station, q DN q Station,(‘-JDN q Station,ODN DN-05 DN-06 DN-07 DN-08 DN-09 DN-10 DN-11 DN-12 Station, DSS Key DSS Key Type 1 Number 1 I I I 6-249 06 I EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Type OHCA Circuit Primary Directory Number Intercom Number Station Name Dyes, Model q No ---------__--- ICM Group Pickup Group Next Hunt Station Class of Service -- Data Line Security Automatic Callback-Trunk Parallel Connect PF Key PF Key Type ONone q EXT--__ -aYes, ONo Dyes, q No Dyes, ONo Number ONone DSS Key DSS Key Type 01 01 02 02 03 03 I 04 I 04 I 05 I 05 Number 06 I 07 0 08 8 09 I 11 12 6-250 I I EXTENSION-STATION Station Equipment No. 7~ Item I Telephone Type and Model I Szt Data OHCA Circuit Directory Number Intercom Number Primary Station Name ____---A-- ICM Group Pickup Group - Next Hunt Station Class of Service q EXT--I- - - -Ncne ONone Data Line Securiiy Automatic Callback-Trunk Parallel Connect I Key Key Type DN-01 PDN Number / SDN mS Day Ring i.]Stat&.q DN DN-02 I /:JStatic-t, ,- q DN I 6-251 Night Ring EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Type Dyes, Model C ‘is ---- Station Name CM Group - Pickup Group - Next Hunt Station Class of Service q EXT ____ 1 Kev Connect 1 Kev 1 DN-01 t 1 None ENone -- Data Line Security Automatic Callback-Trunk Parallel - Tvpe 1 PDN 1 q Yes, C’40 Ryes, CVO c]Yes, CYO Number 1 SDN IllStation. ilDN 1 DN-03 q q DN-04 llStation.nDN DN-02 IPFKey IPFKey Type1 _ Dav Fiina COS 1 Nisht Rina ? I I Station,ODN Station,ODN 1DSS Key IDSS Key Type 1 Number 01 02 06 07 1 08 1 I 09 I I 10 I I 11 I I 12 I I I 6-252 08 I I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model Set Data Type Model OHCA Circuit q ]Yes, q No Primary Directory Number ---- Intercom Number Station Name ____------ ICM Group Pickup Group - Next Hunt Station [7EXT Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect ONone - __-- ONone -- ayes, q No [7Yes, q No ayes, q ]No Number DN-01 1 SDN COS 1 q PDN DN-02 ]Station.ODN Station,nDN DN-05 OStation,[IIDN DN-06 OStation.aDN DN-07 CjStation.aDN DN-08 q DN-09 [7Station,nDN Station.ODN DN-11 q q DN-12 1 loStation,[7DN 1 DN-10 Station.CJDN Station,nDN I DSS Key DSS Key Type Number I Number 01 01 I 02 I 06 t-6 ’ Station,nDN q q DN-04 02 Night Ring / (7Station.oDN DN-03 1PF KeyI-PF KeVrype 1 Day Ring 1 07 07 08 08 6-253 1 I J EXTENSION-STATION Station Equipment NC Set Data Telephone Type and MOEI OHCA Circuit Primary Directory Number Intercom Number Motel TYPE --J’er ~No -_-- - Station Name ICM Group -_-------_ - Pickup Group Next Hunt Station u None - IEX- --_- Class of Service - DYES. [?No ~YEE. q No Data Line Security AutorSiatic Callback-Trunk Parallel Connect : Key 1 Key Type 1 I DN-01 DYES. q ]No h;mber PDN 1 SDN fJStation, COS q i DN-04 / DN-06 llStation.nDN i DN-06 fJStation,ODN / DN-03 DN-07 DN-08 DN-09 DN-10 DN-11 DN-12 J Number 01 07 08 09 11 12 q q q q q 1 Day 1 Night Station, ~DN Station,nDN Station,ODN Station, [7DN . Station,nDN Station, q DN Station,nDN q astation, q Station. DN DN DSS Key DSS Key Type 01 Ring DN q q q i DN-02 1 ONone Number Ring I EXTENSION-STATION Station Equipment No. Set Data Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Model EN0 - - - ___------YNone TEXT ONone Next Hunt Station Class of Service - Data Line Security Automatic-Calfback-Trunk Parallel Connect I ‘2 I Type IJYes, - q Yes, CNo q Yes, CNo Byes, CNo I 6-255 EXTENSION-STATION Station Equipment NC Item Set Data Telephcne Type and Moc?l Type OHCA Circuit nYes, CNo Primary Directory Number _--Intercom Number Model Station Name CM Group Pickup Group Next Hunt Station -- Class of Service -- Data Line Security Automatic Callback-Trunk a y e s , ONo q EXT_--- Parallel Connect 12 DNone ONone q Yes, q No i I ~~~ 6-256 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Set Data Model TYPO q Yes, CNo - - - - - - - - - - - - - - 0 None - - Pickup Group Next Hunt Station q EXT_-__ Class of Service Data Line Security q Yes.CNo Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN - ONone - ayes, CNo q Yes, ENo Number SDN COS Day Ring Night Ring /--@ation. q DN DN-02 @ation,ODN DN-03 q q fJ.Station. q jJStation,q DN-04 DN-OS DN-06 Station, DN DN DN OStation,jJDN DN-07 q DN-08 /-JStation.[7DN q q q q DN-09 DN-10 DN-11 DN-12 6-257 Station, q DN fStation,ODN Station,nDN Station,ODN Station, q DN , EXTENSION-STATION Station Equipme? No. Set Data Item Telephone Type azd Model Model OHCA Circuit Type ayes,q Primary Directory Xumber _-_- Intercom Number - Station Name ____------ ICM Group - Pickup Group - Next Hunt Station q EXT__-- Class of Service Data Line Security Automatic CallbacGTrunk Parallel Connect - No - - CNone ONone - q Yes, q No aYes, ONo [7Yes, q No q q q q q q DN-07 DN-06 DN-09 DN-10 DN-11 DN-12 [ PF Key-1 PF Key Type 1 Number Station.[7DN StationJJDN ]Station,nDN Station, q DN Station,ODN Station.C]DN (“wl”’ 1 Key Type / 01 02 03 05 06 06 07 09 10 I 11 I I 12 I 6-258 Number EXTENSION-STATION Station Equipmer;: No. I Item ,- Telephone Type ant Inode OHCA Circuit T Set Data Type Model q Yes, ONo Primary Directory Nsnber Intercom Number -- Station Name ICM Group Pickup Group -- Next Hunt Station q ]EXT_--- Class of Service Data Line Security Automatic Caltback-Trunk Parallel Connect Key Key Type DN-01 PDN ONone ONone -- ayes, q No C]Yes, q No Dyes, q No Number SDN COS Day Ring DN-03 q q q DN-04 lnStation,nDN DN-Ok astation, q DN DN-02 Station,C]DN Station, q DN Station.nDN 1 astation, q DN DN-06 q q q q q q DN-07 DN-08 DN-09 DN-10 DN-11 DN-12 PF Kay .PF Key-Type q Station, q Station, DN DN Station,nDN Station, [7DN Station, q DN Station,flDN Number 01 02 03 04 05 ,08 07 08 1081 1 1 I 09 I I 10 I I 11 12 I 1 1 6-259 1 Night Ring EXTENSION-STATION Station Equipment No. Set Data item Telephone Type and Model OHCA Circuit Primary Directory Number Model Type q Yes, q No intercom Number - Station Name ICM Group Pickup Group - - - - - - - - - ONone - Next Hunt Station q EXT_--- Class of Service Data Line Security Dyes.. Automatic Callback-Trunk Parallel Connect q Yes, q No q Yes, q No PF Key PF Key Type - - - - Number ONone ONo DSS Key DSS Key Type 01 01 I 04 I 05 08 07 08 I 07 I 08 09 I 10 I I 11 I I 12 6-260 Number EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit. Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Se? Da!:? MOCGI Type aYes, q No ---_ - - - - - - - - - 0 None Yone q EXT 1 Dyes, ONo ayes, q No q Yes, q No Number 1 1 DSS Key 1DSS Key Type 06 07 6-261 Number I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model Set Data Model Type OHCA Circuit q Yes, NO Primary Directory Number -_-- intercom Number - Station Name - - - - - - - - - - ICM Group - Pickup Group - Next Hunt Station q EXT_-__ Class of Service aYes, Data Line Security Automatic Callback-Trunk Parallel Connect Key 1 Key Type 1 - ONone - Dyes, Dyes, ONone ~No ]NO ~NO Number 1 SDN COS 1 6-262 Day Ring 1 Night Ring 1 EXTENSION-STATION Station Equipment No. Item j,- Set Data Telephone Type and Model Type OHCA Circuit. ZYes, Model ]No Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station ,Z]EXT 0 N Class of Service Data Line Security - Automatic Callback-Trunk Parallel Connect Key 1 Key TYP DN-01 0 None -- 1 o n e - :xYes, ~No JYes, ~NO aYes, ,zNo Number 1 SDN PDN COS j OStation,aDN q DN-03 aStation,[ZlDN DN-04 aStation, ODN RN-05 _ aStation, C]DN DN-06 aStation, [7DN DN-07 aStation, ODN DN-08 q DN-09 aStation, ODN q q q DN-11 DN-12 PF Key PF Key Type Number 01 02 02 I 03 Station,ODN I 03 04 04 05 05 06 07 08 6-263 I Station, [7DN Station,ODN Station. q DN Station,ODN DSS Key DSS Key Type 01 Night Ring 1 1 DN-02 DN-10 Day Ring Number EXTENSION-STATION Station Eqc zme-: No. he Set Data I Telephone T;,se arc Yodel Type OHCA Circu: UYes, Primary Dire,zory h _ nber - - Intercom Nucber - - Station Namt _-__------ ICM Group - Pickup Grou; - Next Hunt Ststion q EXT___- Class of Ser. ce OF:3 - - .aYes,q Data Line Security Automatic Modei Czilback-Trunk JNone ONone ]No ayes, aNo ayes,q Parallel Corvect - No q q q DN-10 DN-11 DN-12 1 PF Key PF Key Type Station,nDN Station, q DN Station,C]DN DSS Key DSS Key Type Number Number 01 02 06 06 07 07 08 08 I 09 I 10 I I I 12 6-264 %a 7 I 1 EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Sst Datz Type q Yes, ~‘4 Intercom Number - Station Name ____------ ICM Group Pickup Group - Next Hunt Station Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect - - !.bjel - - - Nc.:e TEXT q - h::e - - q Yes, C:.a ayes, I*,3 q Yes, Cl.3 6-265 EXTENSION-STATION Station Equipmc -t No. SE: Data Item Telephone Type 2-d Model OHCA Gircujt-- q Yes, q No Primary Directory ‘( Jmber - Intercom Number - Station Name --me-----_ - ICM Group - - - - Pickup Group Next Hunt Station Class of Service q EXT---_ Data Line Security Dyes, A u t o m a t i c Callbam-Trunk Parallel Connect 1 Mtcal Type Key Key We DN-01 PDN - - 0 Nor+ - C]NX ONo ayes, ~NO Dyes, q No 1 SDN COS . Number Day Ring Night Ring ~IS:aion.j-JDN DN-02 /~S:ation,nDN DN-03 /IStattion,nDN ’ DN-04 /~S:ation,~DN F DN-05 [~Sation, GDN ’ q DN-06 IlS!ation, DN! DN-07 IF-Station. ilDN i DN-08 IFStation,q ]DNj DN-09 IrStation,C]DN f DN-10 i~Station.rlDN i DN-11 !~Station,q DN f I~Station,q DN ] DN-12 PF Key PF Key Typa Number 1DSS Key 1DSS Key Type 1 Number I 01 I I 02 I I 03 04 05 06 10 11 12 6-266 EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model Model CHCA-Cirwt Type aYes,q ]No Primary Directory Number - - intercom Number - Station Name ___------- ICM Group - Pickup Group - Next Hunt Station q EXT-__- Class of Service - - ayes, q Data- Line Security 0 None - Automatic Callback-Trunk ayes, q Parallel Connect [7Yes, Key Key Type DN-01 PDN ONone No No ONo SDN COS 1 Number DN-OS DN-04 DN-06 DN-06 DN-07 DN-08 DN-09 DN-10 DN-11 DN-12 1PF Key 1PF Key Type 1 01 Night Ring 1 q DbJI Station, q DN C]Station, q DN q Station, q DN q ]Station, q DN q Station.ODbsl q Station,[7DN q Station. q DN q Station, q DN q Station, q DN q Station,nDN q Station, q DN q q DN-02 I Day Ring 1 Number DSS Key DSS Kay Type 01 I 02 03 I 04 I I 05 I 05 06 06 r-~ 0 7 -07 08 6-267 -69 I ]Station, I I I Number EXTENSION-STATION Station Equipment No. Set Dora item - Telephone Type and Model OHCA Circuit Primary Directory Number I Type Model q Yes, JNo ---- intercom Number Station Name ICM Group Pickup Group Next Hunt Station ONone -q EXT 1 N o Class of Service Data Lie Security -- Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN n q Yes, ?No q Yes.7No aYes. JNo Night Ring : q Strcn, ODN q Stint, ZDN q st=cn.~DN q Srzccn.:JDN I DN-03 DN-04 , I 1 1 I 4 , / lnStrcn. iJDN 1 t DN;O5 1 I DN-06 q q DN-07 .S?zazn. q DN .. S:3xn, /JDN )JStzcn./-JDN 1DN-08 1 I DN-09 1 q St3:on,mDN q Stdon. c IDN q Stazon.~DN OStron.q DN DN-10 DN-11 DN-12 Number DSS Key 3SS Key Type Number 01 02 03 02 03 04 05 04 05 06 06 07 08 Day Ring SD% cos Number DN-02 PF Key PF Key Type 01 e - 6-2%8 I EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Made1 Type OHCA ciccu it Primary Directory Number IJYes. - - Mdel C:io - - Intercom Number -- Station Name ICM Group ---_------ Pickup Group Next Hunt Station : Class of Service -- i Data Line Securiiy 1Automatic Callback-Trunk t Parallel Connect g Key Key Type PDN 1DN-01 DN-02 J None q EXT--__ -Dyes, EN0 ayes., C?!o q Yes, EN0 ONone Number SDN COS q q Day Ring Station./-JDN Station.nDN 1DSS Key 1DSS Key Type 1 05 06 07 08 I 12 I I 6-269 Night Ring Number I EXTENSION-STATION Station Equipment No. item Telephone Type and Model Set Data Model Type OHCA Circuit q Yes, q Primary Directory Number - Intercom Number - Station Name --___----- ICM Group - Pickup Group - Next Hunt Station q EXT___- Class of Service - - - NO - - ONone - Automatic Callback-lnmk- ayes, q No q Yes, ONo Parallel Connect aYes, Data Line Security Key DN-01 Key Type PDN ONone NO Number SDNCOS / /-Jhtion,[rDN DN-02 DN-04 q q DN-05 /JStation, CDN DN-06 fJStation, CDN / Station, CDN ]Stalion, CDN q Station.CDN q Station, CDN q Station,CDN q Station. EDN q Station, EDN q Station,~DN DN-07 DN-08 DN-09 DN-10 DN-11 ) DN-12 L DSS Key DSS Key Type PF Key PF Key Type Number 01 01 02 02 03 03 04 04 Xl’ i O8 i I 12 Night Ring [7Stztion, CDN DN-03 1 Day Ring I 6-270 Number J EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directov Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security /U&m&k Cal+ba&-Trunk Parallel Connect Set Data Model Type q Yes, ?No ___------- ONone q EXT---_ ayes, INone ~NO q Yes, ]No aYes, ]No q q DN-07 DN-08 DN-09 astation,q DN q Station, q DN DN-10 DN-11 [7Station,nDN q Station,uDN DN-12 1PF Key 1PF Key Type } DSS Key DSS Key Type Number 0: 01 02 05 06 08 07 i 08 Station,ODN Station,ODN 1 I 09 I I 10 I I 12 I I 6-271 Number EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary DirectoryNumber Intercom Number Set Data Ty~s Model :\10 c]Yss, - - - - - Station Name ___------_ ICM Group Pickup Group - iJext Hunt Station q EXT__-_ -q Yas, cvo (7Yes, Lb40 q Yes. c\io Class of Service Data Line Security Automatic Callback-Trunk Parallel Connect Key DN-01 Key Type PDN -- 7 None ONone SDN COS Numbs- q q q DN-02 Station,L1DN DN-05 iIN- 1 jflStation,ODN 1 DN-04 PF Key PF Key Type Number 01 02 02 I Station, 1DSS Key 1DSS Key Type 1 01 Night Ring Station,nDN q DN 1 astation, q DN q Station,nDN DN-03 Day Ring Number 1 1 04 05 06 07 t 08 I 1 08 09 10 I 11 t 12 I I 6-272 EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary DiFecfory Wwnber TYPO fJYs:s.. Model ~‘rt3 ---- Intercom Number Station Name CM Group Pickup Group --_------- 1 None - Next Hunt Station Class of Service Data Line Security At&wnalicCaJIba&-Trunk Parallel Connect cI]Yes, pa0 1 SDN CX Numb DN-01 PDN EStatio- DN-02 Day Ring 1 IDK CStatio- 7DN ; ~statb7.. 10~ 1 DN-03 DN-04 IYStatio- TDN i DN-CK EStatio: IDN ( ImoE .. CStatior IDN j DN-07 aStat+- 7DN 1 DN-08 ~Statior..~DN DN-09 nStatio:- DN-10 ~Statiw- Z;DN DN-11 OStatio-.. 7DN DN-12 ,uStatiot. IDN, 1PF Key 1PF Key Type 1 1 Jot4 j DSS Key DSS Key Type N-r 01 01 02 02 Number I 03 I 04 04 05 05 I-=;‘“’ 12 Night Ring I I 6-273 I I EXTENSION-STATION Sts:ion Equipment No. Set Data Item Telephone Type and Model Model OHCA Circuit Type [7Yes, Pri.mary Directory Number - Intercom Number - Station Name &--------- ICM Group - Picjtup Group Next Hunt Station ONone IJExT rJ N o Class of Service aYes, Data Line Security AtiomaticCaHbah~Trunk Parallel 1 Key DN-01 Connect 1 Key Type c]Yes, - (7No - - q ayes, 1 - n [7No No [7No Number PDN DN-02 DN-03 DN-04 1 SDN COS q q q q q j Station.CjDN ]Station, /JStation,nDN DN-09 ! DN DN-06 DN-08 F;glt f ng Station, i-JON , jJStation,C]DN q q Day Ring Station,nDN DN-05 DN-07 ) e Station,nDN ]Station,C]DN 1 OStation,ODN I DN-10 /-Jtation,nDN DN-11 OStation, DK12 q If I I PF Key .PF Key Type 01 I Number f q DN ation,nDN DSS Key DSS Key Type Number 01 02 03 02 03 04 04 05 ’ 06 07 6-274 I ! < I EXTENSION-STATION Station EzJipre -. ‘,2. ‘:3rn Set Data I Telephors Type J-:: 1.‘:3el OHCA Cs:: Jit ! Type Model Eyes, flNo Primary C -xtor, _ -c 3 Intercom ‘.dmbe- - Station I\iz77e -----_---- ICM Grocz - Pickup Grzclp - Next HUG: Static- CEXT _ Class of S2fvice ryes, Data Line Securr Automatic Zallba:* Parallel C 2 nnec: PF Key PF Key Tyx --rLnk - ONone - _ _ _ ONo Eyes, q No Eyes, q No Number 01 02 03 04 05 08 07 08 09 I 11 I 6-275 ONone EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Byes, q k ---- Intercom Number ‘Station Name - ICM Group - Pickup Group Next Hunt Station Class of Service - - Data Line Security :., Automa& CaHback-Trunk Parallel Connect Key DN-01 Key Type Model Type - _ - - - - - - - - - 1 None q EXT ____ -/JYes, ON: q Yes. Ok aYes, ON: ONone Number Day Ring SDN COS I DN-05 q q q q q i DN-06 fJStation,ODN j DN-07 q / DN-08 fJStation.[7DN DN-09 ITStation. IlDN PDN : DN-02 j DN-03 ; DN-04 q q q DN-10 DN-11 DN-12 PF Key PF Key Type Station,ODN Station,nDN Station, q ]DN Station,ODN Station,C]DN Station, q DN Station./-JDN Station,ODN ]Station, q DN DSS Key DSS Key Type Number 01 01 02 02 03 03 I 6-276 Night Ring Number 7 EXTENSION-STATION Station Equipmer;: No. Item Set Data Telephone Type ant Model Type Mod61 OHCA Circuit Dyes, q Primary Directory Number No ---- Intercom Number Station Name ICM Group Pickup Group -- Next Hunt Station q EXT-___ Class of Service -- Data Line Security kuturnatfcCa~~back-Trunk Parallel Connect PF Key .PF Key Type 1 01 02 I I 03 1 I 04 0 None ONone Dyes, q No Dyes, q No OYes, q No Number 1 DSS Key 1DSS Key Type 1 I 01 I Number 1 I 02 03 I 06 07 07 08 08 09 10 11 12 6-277 a 1 I I EXTENSION-STATION Station Equipment No. item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Atttomatie CaHba&-lrunk Parallel Connect %t Data Tyx - ,‘A$5 - kdel ]No - - - - - - - - - - - - - CN:-a - EE:- - - - - E’s:. JNo Ekt:;. ]NO c\:;:z. ~NO ONone q q q q q DN-08 DN-09 DN-10 DN-11 DN-12 1 PF Kev 1PF Kev TYW Station,nDN Station,ODN Station, (7DN Station,ODN Station. q DN I 1DSS Key 1DSS Key Type 1 02 03 06 07 07 08 1 09 6-278 08 1 I Number EXTENSION-STATION Station Equipment No. Item Telepkc -e Type and Model Set Data Model OHCA C :cuit Type ayes, Primary Directory Number - lntercorr Number - Station Kame _--------- ICM GrcLp - Pickup Group Next Hunt Station Class oi Service Data Line Security - - [?No - - - 0 None q EXT ---- ONone - q Yes, q No Automat:& Callback-Trunk aYes, Parallel Connect - NO aYes, q No 6-279 EXTENSION-STATION Station Equipment No. hem Telephone Type and Model OHCA Circuit Set Data Model Type q Yes, ONo Primary Directory Number Intercom Number - Station Name ICM Group __-_------ Pickup Group Next Hunt Station - Class of Service Data Line Security - - - - - - ONone q DT ____ - ONone - Automatic Callback-Trunk Parallel Connect ayes, q No aYes, q No Dyes, q No Key Key Type Number DN-01 PDN SDN COS 1 DN-07 q Station,uDN q Station, q DN q Station.0~~ q Station, q DN q Station.ODN q Station,C]DN q Station,nDN DN-08 nStation,nDN DN-09 /-J%tion. DN-10 jJStation,ODN DN-02 DN-03 DN-04 DN-06 DN-06 q q DN-11 f DN-12 6-280 q DN Station,ODN Station. q DN Day Ring Night Ring EXTENSION-STATION S:z:ion Equiprsnt No. Item Set Deta -5 sphc ;t Type :nd Model T,,pe r-r _ .tiA C.rcuit ryes, Mode’ ?No >-,mary Iirecto:! Number j ::trcom Numbe- - S:a!ion Name - ic’.! GfCJp 7 ckup Group ’ =xt Hcnt Static*.C 3s oi Service - - - - - - - - - - TEXT - l7-J None - G.:a Lir.,e Secur:j TYes, i JNo &,:ornatic Callbzk-Trunk TYes, ?No Pzallel Conner aYes, ]No - - ZNone EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group - Data Line Security Automatic Callback-Trunk Key DN-01 Key Type PDN M3del - - - ___------- q Next Hunt Station Class of Service Connect ayes. q Nc - Pickup Group Parallel Type r None EXT ONone - - OYes, ONo q Yes, q Nc ayes, q Nc Number SDN COS Day Ring DStation, /-JDN DN-02 /-JStation,~DN DN-03 /JStation, ODN DN-06 q q DN-06 C]Station, /JDN DN-07 /-JMion, q ]DN DN-08 ~Station,f’JDN DN-09 ~Station.~DN DN-10 C]Station.nDN DN-11 /-JStation. q DN DN-04 Station,ODN PF Key PF Key Type 4 Station,ODN q DN-12 Station,ODN 1DSS Key 1DSS Key Type 1 Number 01 02 03 I 04 I 05 I 04 I I I 05 06 06 07 07 08 08 I 09 10 11 12 Night Ring I 6-282 1 I I Number EXTENSION-STATION Station Equipmer: No. Item Telephone Type an: Model OHCA Circuit Primary Directory h:,mber Intercom Number ----- Station Name CM Group - Pickup Group - Next Hunt Station Class of Service q EXT ---- Data Line Security Automatic Callback-Trunk Parallel Connect - ON>-; INone -- q Yes, ENo q ]Yes, ~No Dyes, q NO , 01 DSS Key DSS Key Type 1 i Number EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Pickup Group Next Hunt Station Class of Service Data Line Security Set Data Model Type q Yes, EN0 - - - __-------- 0 None q EXT__-aYes. Automatic Callback-Trunk ayes, Parallel Connect ayes, ONone ~No CNo ENo Number 1 PF Key 1PF Key Type 1 Number SDN COS Day Ring Night Ring Number DSS Key DSS Key Type 01 -ii 02 I 03 I 04 04 05 06 05 -. 06 07 07 i 08 1 08 6-284 I I 1 I I EXTENSION-STATION Station Equipment No. Item Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name Set Data Model Type q ]Yes, ~No - - - _-_---e-e- ICM Group - Pickup Group Next Hunt Station Class of Service - - - - Data Line Security Automatic Callback-Tank Parallel Connect PF Key -PF Key-Type 01 02 - ONone q EXT__-_ ONone q Yes, ;]No q Yes, NO q Yes, NO Number DSS Key DSS Key Type 01 1 05 05 .06’ 06 07 07 08 08 09 10 1 1 6-285 Number EXTENSION-STATION Station Equipmec: No. Set Data Item Telephone Type and Mode! OHCA Circuit Primary Directory Ncmber intercom Number Station Name ICM Group Model Type IYes, ~NO - - - - __-------- Pickup Group Next Hunt Station IEXT _--- Class of Service - IYes. r]Yes, JYes, ~No ~No ~NO Data Line Security Automatic Callback-Trunk Parallel Connect 0 None ONone 6-286 EXTENSION-STATION Station Equipment No. Set Cz:2 Item Telephone Type and Model OHCA Circuit Primary Direciory Number Intercom Number Uode Type q Yes, NO - - - - - Station Name ICM Group - - - - - - - - - - Pickup Group Next Hunt Station [? h m e TEXT :N~~-z Class of Service - Data Line Security Automatic Callback-Trunk Parallel Connect Key Key Type DN-01 PDN - q Yes, q No q Yes, q ]No Dyes, q No Number SDN CC3 / Day Ring Night Ring FStation, IDN 1 ‘.; Station ,,DNi ii-S!ation.IDN 1 - DN-02 DN-03 DN-04 i-Station.-DN DN-05 1 DN-06 T - Station. ZDN ! ‘-Station.IDN i ‘:I- DN-07 ‘FStation.-DN DN-08 jr Station. ~DN DN-09 irStation.zDN 1 DN-10 \rStation.‘DN i 1 DN-11 DN-12 PF Kay .PF Kay Type. Number ZSS Key DSS Key Type C? 01 02 03 I 04 I 05 0 6 0 6 07 ~ 07 08 ! 08 I 09 I 11 12 6-237 Number EXTENSION-STATION Station E2Jipmer.r No. ::9 m Set Data Telephorb? Type ant Model L Model OHCA Ci->;iit Type ayes, Primary L-xtory Ncmber _--- kIterCOm ‘- Jrfber - Station N-3e ____------ ICM GroLz - Pickup - GPJp ONo - - 0 None Next Hun: Station q EXT-_-_ Class of &vice Dyes, q Data Line Security Automatic Callback-Trunk Parallel Connect 1 Kev 1 L(IV Tvoe No ..flYes, q NO ayes., q No Number PF Key PF Key Type / I 01 02 ONone ) SDN DSS Key DSS Key Type Number 05 I I/ I 06 1 04 I 07 I 1 08 1 Day Ring Night Ring Number 01 ! I 03 COS 1 02 03 04 I 05 08 6-288 I 1 I EXTENSION-STATION Station Equipment No. Item Set Data Telephone Type and Model OHCA Circuit Primary Directory Number Intercom Number Station Name ICM Group Model Type q Yes. q No - - - - - --__-----0 None - Pickup Group Next Hunt Station q EXT ---- Class of Service - Data Line Security Automatic Callback-Twk Parallel Connect Key Key Type DN-01 PDN ONone - q Yes, q No q Yes, ~NO q Yes, ONo SDN COS Number q q DN OStation, q DN OStation, q DN @tation, q DN OStation,q DN q Station, q DN q ]Station,nDN q Station, q DN f q Station. q DN 1 DN-03 DN-04 DN-05 DN-06 DN-07 DN-06 DN-09 I Station, DN-11 OStation,nDN DN-12 q -PF Key -ff Key Type Number Station. q 01 02 02 03 03 05 05 06 . 6-289 I DN DSS Key DSS Key Type 01 06 Night Ring IlStation. IlDN DN-02 DN-10 1 Day ?ng Number I EXTENSION-STATION Station Equipmen; No. Set Data Item Telephc:? Type and Model Model Type OHCA C rxit q Yes, ~NO Primary 3irecXq N-umber - Intercom Number - Station hame - - - - - - - - - - CM Grcl;p - Pickup G-oup - Next Hurt Station q EXT ---- Class of Service Dyes, ~NO c]Yes, ~NO Data Lint Security Automat;s.Callback-Trunk - - - ONone - ONone q Yes, ~NO Parallel Connect Key 1 Key Type : DN-01 / - Num!xr PDN /JStation.nDN q q q DN-02 j , DN-03 / DN-04 / DN-05 j DN-07 j DN-09 DN-10 DN-11 ) ON-12 IPFKey IPFKeyTypeI Number 1 IDSSKeyIDSSKeyTypeI 02 I 03 I I 04 I t 06 1 06 07 07 08 08 I 09 I 10 1 I 11 I I 12 I 6-290 f 1 NGht Ring I I DN Station,ODN I 01 I 03 DN q Station.~DN q Station, q DN q Station,ODN q Station,ODN q Station, q DN q Station, q DN q Station.ODN I I DN-08 q Station. q Station. nStation.aDN ! I DN-06 i Day Ring j SDN COS I I ! I Number EXTENSION-DSS CONSOLE I Item Model -‘X-T61 640 dX-T1 23240 ‘75d-: Pair EZF-s cn 3 3r 4 digits: 3tw~t~y nwcdr PF Key -#;e PF Key h --nber Default Value 1 KX-T123240 (7040) 3 SS (ICM). ONE -3UCt- EXT FEAT, ,ALL PAR, CAL L STA. F;N TRAN. SPLIT, ! -C>NE-BRK, or balk . or 2 digits: irrtenz-n nurter for ‘DSS (ICM)” -3ximum 16 dig= >f diair-s number: destination number for 9NE T$Z*JCH” blank Mank blank DSS Ke? -ype ‘.1W, LOGIN. AL&?M. ES3 (DN), DSS (KM). ,ZNE TOUCH. PF’.‘-C% EXT FEAT, CALL PAR, ZALL STA, RNG TAN. SPLIT, TONE-BRK, :- blank blank DSS Kej ‘(umber i 3 or 4 digits: direccq nurcer for “DSS (DN) / - or 2 digits: he-m w-car for “DSS (ICM)” / Taximum 16 digits: destirzion number for “ONE TOUCH’ I blank 6291 EXTENSION-DSS CONSOLE Station Equipment No. item Model DKX-T12324C (7040) Pair Extension PF Cl2 - - - - PF Key Type a KX-la’ 640 (3 or 4digti DN) Set Data 1 QY 0’ Set Data PF Key Number _ PF Key PF Key Type PF Key Number 29 ) I 70 03 :1 54 72 05 73 06 14 07 15 08 16 DSS . Key DSS Key Type Set Data ,_ Set Data DSS Key Number _ DSS Key 01 17 02 18 03 19 04 20 05 21 06 22 07 23 08 24 09 25 10 26 11 27 12 28 13 29 14 30 15 31 16 32 6-292 Set Data DSS Key Type DSS Key Number . EXTENSION-DSS CONSOLE Station Equipment No. Item Sst Datz Model q Pair Extension - c PF Key KX-T123240(7040) - - 3 KX-TS - 540 - (3 or 4-c sit DN) Set Data PF Key Type 1 Key PF Key Number PF Key Type 1 PF Key Number -c -- 01 I Set Data fl I 02 1I I I .. -2 07 08 t Set Data DSS Key DSS Key Type DSS Key Number _ Dss, KsY DSS Key Type 01 ‘7 02 ‘3 03 ‘3 04 23 05 it 6-293 Set Data DSS Key Number EXTENSION-DSS Station I Equipment Item No. Set Data I Model q KX-T12324C(:C40) Pair Extension - i PF Key 01 - - I 0 KX-T61640 - (3 or 4digii DN) Set Data PF Key Type CONSOLE PF Key Number j/ _; PF , PF Key Type ,: KeY )! 09 02 j 10 03 / 11 04 j 12 05 06 07 15 08 16 6-294 Set Data PF Ksy Numbs EXTENSION-DSS CONSOLE Station Equipment No .item Set Data I Model q KX-T1232C!7040) Pair Extension - - - - q (3or4digit KX-T61640 DN) 1 PF Key Set Data PF Key Type _ PF Key ?:umber PF , PF Key Type Key 01 09 02 10 03 11 04 12 05 13 06 14 07 15 08 16 6-295 Set Data PF Key Number EXTENSION-DSS CONSOLE Station Equipment No. Set Data Model q ]KX-T123240(7040) q Pair Extension - PF Key - - - (3 or4digit DN) Set Data PF Key Type KX-T61640 PF Key Number ,_ PF ,. PF Key Type Key 01 09 02 10 03 11 04 12 05 13 06 14 07 15 06 16 6-296 Set Data PF Key Number EXTENSION-DSS CONSOLE Station Equipment No. Item Model q Pair Extension -_-- PF Key PF Key Type I S-3 Data I KX-TlZ4C '-.:A.:) 1 KX-T61W ‘T‘- :r C<,I$ DN) Set Data PF Ksy Nu-rer _. PF Key 01 09 02 10 03 11 04 12 05 13 06 14 07 15 08 16 Set Data DSS KW DSSKey Type 1 DSS V&y Ncber Set Data PF Key Type PF Key Number Set Data DSS Key DSS Key Type 1 DSS Key Number 17 I 18 06 I 10 I 26 I 11 27 t2 28 13 29 14 30 15 31 16 32 6-297 EXTENSION-DSS CONSOLE Station Equipr + ;t No. Set Data Item Model qKX-1123240(7040) Pair Extension - PF Key .. ) - - - (3or4digit Set Data _ ?F Key -!3e q PF Key Number KX-T61640 DN) ,_ PF Key 01 09 02 10 03 11 04 12 05 13 06 14 07 15 08 16 8-298 Set Data PF Key Type PF Key Number EXTENSION-DSS CONSOLE Stat& Equipment No. Item Set Data Model q ~~-Ti23i~(7040) Pair Extension - PF Key Set Data PF Key Type - - 0 KX-T61640 - (3or4digit DN) PF Key Number 01 09 02 10 CCL PF Key Type 1 1 16 18 3 t 20 I Tl 08 24 I -25- 09 10 26 27 I J I 19 I 7 12 PF Key Number .- 08 0 Set Data P F Key I 28 29 32 6-299 t I I I I I EXTENSION-DSS CONSOLE Station Equipment No. I Item Set Data Model q KX-T123240(7040) Pair - Extension PF , Key PF Key Type - - - q (3or4digit Set Data PF Key Number KX-T61640 DN) _ PF Key 01 09 02 10 03 11 04 12 05 13 06 14 07 15 08 16 Set Data DSS Key DSS Key Type DSS Key Number _ DSS Key 01 17 02 18 03 19 04 20 6-300 Set PF Key Type 3ata PF Key Number f Set Data DSS Key Type DSS Key Number EXTENSION-DSS CONSOLE Staticn E q u i p m e n t N o . Item Set Data I ~Model q / Pair Extension --_- I i KX-T123240(7040) (?KxT61640 (3 or4digit CN) Set Data PF / Key / PF Key Type PF Key Number i 01 1 1 j 02 ! j 10 03 1 11 04 / ! 12 O5 06 I i 07 1 j 15 O8 I / DSS W Set Data PF : Key PF Key Type PF Key Number i 09 1 3 : 14 Set Data DSS Key Type 1 DSS Key Number 16 Set Data ./ D S S DSS Key Number j Key DSS Key Type 1 j 01 17 1 -I ‘8 I 03 19 04 3 . 20 05 1d 21 06 j 22 07 i 23 08 : 24 09 ', 25 6-301 EXTENSION-D% Station Equipment No. Set Data Model Pair Extension EKX-T123240 - - - (7240) 0 KX-T51640 - (3 or 4digit DN) 05 13 06 14 07 15 08 16 6-302 CONSOLE EXTENSION-DSSCONSOLE S t a t i o n Equipment item No. Set Data I Model q KX-T: 23240 ‘-:LO) Pair Extension - - - - 2 KX-T61 CO .I Y 4Cigit DN) Set Data DSS . Key DSS Key Type 1 DSS Key Nmtw DSS , Key DSS Key Type 0’ I 17 02 ia 03 19 04 20 05 21 22 23 25 26 11 27 t2 28 13 29 14 30 15 31 16 32 6-303 Set Data DSS Key Number EXTENSION-DSS CONSOLE Station Equipment No. Set Data Model q KX-T123240(7040) Pair Extension - PF Key - - KX-T61640 - (3 or 4-digit DN) Set Data PF Key Type q PF Key Number ,_ PF Key 01 09 02 10 03 11 04 12 05 13 06 14 07 15 08 16 6-304 Set Data , PF Key Type PF Key Number EXTENSION-DSS CONSOLE Station Equipment No .Set Data Model q Pair Extension - PF . Key PF Key Type KX-T123240(7040) UKX-T61640 - - - (3orIdigit Set Data PF Key Number DN) _ PF Key PF Key T,z 01 09 02 10 03 " I 04 05 l2 13 I 06 14 07 15 08 16 6-305 Set ika , ?S Key Number EXTENSION-DSS CONSOLE Station Equipment No. Item Set Data I Model q KX-T123240(7040) Pair Extension - - - - (3or4digit DN) Set Data ~ PF ~Key 0 KX-T61640 ,_ PF Key Number PF ,. PF Key Type Key Set Data PF Key Number 09 10 11 I 12 I 13 14 15 t 08 I 16 Set Data DSS DSS Key Number Key 1DSS Key Type I 18 19 23 I I 09 10 11 27 12 28 13 29 30 1s 31 16 32 6-306 I EXTENSION-DSS CONSOLE Station Equipment No. Item Set Data Model q Pair Extension --__ PF Key KX-7232:: T040) 0 KX-T61640 ;3 or 4digit DN) Set Data PF Key Type _ PF Key ‘,;mber PF Key 01 09 02 10 03 11 04 12 05 13 06 14 07 15 08 16 DSS Key DSS Key Type 1 Set Data DSS Key Umber Set Data PF Key Type _ DSS, Key DSS Key Type 01 17 02 18 03 19 04 20 6-307 PF Key Number Set Data DSS Key Number .,*,’ ‘&A- EXTENSION-DOORPHONE 3oor- Tenant Ihone Default S e t D a t a Va,ue No. q q 1 Open Duration Doorphone Call Assignment Default Value Set Data Tenant 1 Tenant 1 1 or 2 digits Tenant 2 I tliuil ( I III I I ) 1 Ilf!M tlOt.tl:ltl(O) 0 0: Door cannot be opened. 1 to 10: Door opening duration in second(s) 1hlaJll Value set Data UPICKUP _ TEXT - 2 - - - - digits (01 lo 32) 3 or 4 digits (UN) A l I 1811 “willl A 1 LC” EX T 100 : lor “without ATLC” IIAn 0 Ulanh - - s=QWa) aTenant 1 q 2 q q 3 q I 1 or 2 digits Tenant 2 Tenant 1 0 0: Door cannot be opened. 1 to 10: Door opening duration .in second(s) Tenant 1 0: Door cannot be opened. 1 to 10: Door opening duration in second(s) 0 second(s) 1 or 2 digits 0: Door cannot be opened. 1 to 10: Door opening duration in second(s) Tenant 1 Tenant 2 I Remark: If DPH card was not set beforehand, this screen is not available. 1 digit (1 lo 0) ATT: lor “witll 0 PICKUP 2 digits (01 to 32) AILC” q 3 or 4 digits (DN) EXT loo : EXT 0 I for “wit bout ATLC” clAJ--r 0 Blank second(s) 1 or 2 digits Tenant 2 aTenant 1 4 Tenant 1 n ICM q llCM - 1 digit (1 to 8) ATT: for “with 0 PICKUP 2 digits (01t o 32) ATLC” 3 or 4 digits (DN) EXT loo : for q EXT q lArr q Blank - q lCM q PICKUP q EXT ---IIIAU 0 Blank “without ATLC” 1 digit (1 to 8) ATT: for “with 2 digits (01 to 32) ATLC” 3 or 4 digits (DN) EXT 100 : for “without ATLC” EXTENSION-ATTENDANT CONSOLE TRS LV 1 Default Data 1 Default I I DN Data AT 1 _ _ _ _ (3 or 4 digits) _ - _ _ (3or 4dkW - - 01 blank - - 01 q INT,Elm. q E2, q El & E2. q ALL Tenant 1 AH Position - q Data 1 Default blank (3 or 4 digits) blank El 8 E2 El 8 E2 Tenant 2 ---- (3 or 4 digits) Night ‘G No, Data ablank Default blank 0 blank Overflow Data q INT, q Ei. q E2, q El i E2. q ALL c] blank AI-T 2 PAG blank I I 0 blank - ( 3 0 blank o / Default I blank (3 or L digiS) r d digts) blank r Busv-out Extension 1 data Item lefault Data item TG5 -- -- TG -- kxwle Calling -- TG7 --, Hank :ransfer Recall -- TG3 --. 05 blank ktial Calling Recall -- TG!9 -- 06 blank X Park Recall -- TGlO -- 07 blank ntercept Routing -- TGll -- 08 blank deld Cafl Reminder -- TG12 -- 09 blank External Catling TGl -- TG13 -- 10 blank TG2 -- TG14 -- blank TG3 -- TG15 -- blank TG4 -- TG16 -- 01 blank ntemal Calling Station -- 02 blank ntemat Calling Doorphone 03 blank 04 11 ---- 12 13 ---- ixtemalCaSng Data blank 14 blank 15 blank 16 blank Note: Busy+ut Extension 6-309 3 or 4 digits of Extension number . SPECIAL CARRIER ACCESS-EQUAL ACCESS Ite- Equal Acces! No.1 Service (Equal Access Set) Name (Equal Access Name) Equat AccessCxrterGxfe aYes, q NO ----- Set Data iqual Access Equal Access No.2 No.3 No.4 Defaull Value Equal Acces Dyes, [7No ayes, ~No - - - - - - - - - - - - ( 0 1 t o 16 ( 0 1 t o 1 1 6 q Yes, q No ----( 0 1 t o No blank blank 1E blank Toll Restriction Level ( Toll Restriction Table - (1 to 8) - (1 to 8) - (1 to 8) - (1 to 8) blank Long Distance (Delete) - (0 to 4) - (0 to 4) - (0 to 4) - (0 to 4) blank Long Distance (Insert) - - - - ---_ - blank Local Toll (Delete) - Local Toll (Insert) - Local (Delete; - Local (I nseft) - 0 1 t o Digit Modification - - - - (0 to 4) - - - - (0 to 4) - - - - - - - - (0 to 4) - (0 to 4) - - ---_ - (0 to 4) - - - - (0 to 4) - - - - 13 IYes, q No JYes. ONo IYes. q No JYes,q No IYes. q No JYes. ONo IYes. ONo IYes. ON0 JYes. ONo JYes,q No JYes. ONo JYes, /JNo JYes, q No JYes. ONo JY=, q lh Jyes. 0~0 JYes, I30 JYes,q No IYes, [7No JYes, ONo JYes. ONo JYes.q No IYes, q No JYes. q N0 7Ye.s. q No JYes. ONo 14 JYes. ONo JYes. ONo 15 IYes, ONo JYes. ONo 16 IYes. ~NO JYes, ~NO Trunk Group No. 01 02 03 04 05 06 07 06 09 10 11 12 Note: ltefn _ Selection of value Name letters. numbers, marks within 3 digits blank: not assigning Equal Access Carrier Code 3 digits number Long Distance (Insert) Local Toll (Insert) ,Local (Insert) maximum 4 digits number 7-l - - - aYes. q No JYes, ONo z]Yes, ONo JYes,q No JYes.q No JYes,q No JYes.q No JYes.q No Jyes, ONo JYes, ONo JYes, ONo JYes,q No JYes.q ]No JYes.q No JYes,q JNO JYes,q No - - - - (0 to 4) blank - blank - (0 to 4) blank - blank - ElNo blank IJYes, IJb blank IJYes, q Yes,ONo Dyes, jJNo cI]Yes, q No @es, q No q Yes, q No Dyes, q N0 q Yes, q No aYes, ONo aYes, ONo IJYes, q k q Yes, EN0 Dyes, q No JYes, IJb JYes, q N0 blank blank blank blank blank blank blank blank blank blank blank blank blank blank SPECIAL CARRIER ACCESS-OCC ACCESS (I/2) S e 3ata Item OCC Access No.1 OCC Access ‘Jo.2 Service Dyes, ~NCJ IYes. @No Name --- - - Local Access Code --_---__(Max. Toll Restriction Level Toll Restriction Table 8 digits) - ‘,!.a 8 dic:s - I ----__-- ( 0 1 - (1 to 8) - (1 t o 8) - (Oto 4 ) - (oto 4) - k bia-i (01 to 16) - De& Va(je t o 1 6 . Digit Modification i Long Distance (Delete: ‘/ ! Long Distance (Insert) I ; Local Toll (Delete) Local Toll (Insert) Local (Delete) --me-------- -------_ - 07 08 09 10 11 12 13 - blank - - - - - - - _ - - - - - - - - - (Max. 20 digits) (Oto 4) 20 dihs) (oto 4 ) - - - vax - - - - - (Oto 4 ) - --mm---- (Max. 20 digits) - ONo No - IYes, IYes, IYes. z]Yes, IYes. IYes, IYes, IYes, I]Yes, JYes, IYes. IYes, I]Yes, IYes, JYes. I]Yes. - - - blank blank ---------___ z]Yes, - v-ax 2 0 dgas) --mm-----___ JYes, q 06 - - 16 05 - - Jyes. 04 - - 15 03 - - 14 02 - ---_-----___ q No IYes. q ]No JYes. q No I]Yes. q No IYes, q NO 7Ye.s. (7No IYes, ONo IYes, q No IYes, q No z]Yes. q No IYes. q No IYes. ONo IYes, q No IYes. q No rn.mk Group No. 01 (Max. 20 digits) (0 to 4) - - Local (insert) /1 -------_____ - - blank - vax. 20 diits) q No q No q No q No q No q No ONo q No q No ON0 q No q No q No q No I30 UNo blank blank blank blank blank blank blank blank blank blank blank biank blank blank blankblank Note: Long Distance (Insert) : Local Toll (Insert) Local (Insert) Max. 20 digits consisting of numbers, l , # and marks below H : Home position P : Pause D : Switch to DTMF [ : start of secret numbers ) : end of secret numbers (enter - : Hyphen 7-2 secret marks in a pair) SPECIAL CARRIER ACCESS-OCC ACCESS (2/2) Item Set Data ! OCC Access No.3 OCC Access No.4 1 Set-vice j q Yes,IzNo q Yes, ONo dame I I__- - -ocal Access Code - ioll Restxtion Levf - roll Restfction Tab15 - - - - - - - - . Defauli Value (Max 8 digits) - blank - (Max. 8 d (01 to :q _ (1 to@ - No i _ g i t s ) blank (01~16) (1 to 8) blank blank Digit Mod:Scation Long Cistance (kete) - Long Cistance (Iw3t) ______--__-_ - (0 to A) (0 to 4) - - - _ _ - _ - - (Max. 20 digits) - - - - blank - _ _ _ _ _ _ _ _ - - - - (Max. 2 0 - - (0 to 4) blank - Local Toll (Insert - - - - - _ - - - - - - - - - - - - - - - - - - _----_--(Max. __--_-__ (Max. ~CJww (0 to Al - 20 digits) (0 to A) (0 to 4) - Local (Insert) _----------- - - - - - - - - - - - _ _ _ _ _ _ _ _ (Max- 2 0 blank blank Local (Delete) - blank 63w Local Toll (Delete rrunkWupl\la blank d&W _ _ _ _ _ _ _ _ blank (~.~mw blank Cl Byes, UNo aYes. ONo E IIjYes. ONo ayes, ONo c3 ayes. ONo Dyes. q t-t q Yes.UNo No Dyes. UNo frs OYes, I30 Dyes, ONo blank C6 q Yes. q k q Yes. q No blank c7 IJYes, Elk CJYes, UN0 blank c9 ID=. q N0 q Yes, UN0 10 IJYes. ON0 12 q Yes, q N4 OYes. q N0 q Yes.ON0 UYes. ON0 q Yes.UN0 OYes. EN0 ayes. q No 13 [7Yes, UNo aYes. ONo 14 q Yw q N0 q Yes.ONo q Yes.ONo IJYes. ON0 ayes. ONo Dyes. ONo ci3 11 15 16 . blank blank blank blank blank blank blank blank blank blank blank blank 7-3 Q 8. Toll Restriction TOLL RESTRICTION-AREA/OFFICE CODE TABLE he7 Selection of Value Default Value Local Call Access -1 Yes/No No Restriction Level i?L) 2 digits (01 to 16) 16: for 411,800, 911, NNX 01: NPA except the above codes Office Code Table ‘dumber (OC) blank : for 3 digits Toll Restriction 01 to 64 : for 6 digits Toll Restriction blank 8-1 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (l/8)I Area/Office Code Table No. 1 Local Call Restriction n44:nfi PAAn 11 Code 1 Local Call ResWtion . . Office Co& 216 ~ 2 1 7 218 219 JYes. q No jyes. ON0 1 1 IUYes, LJNol ~No 7~47 1 gYes, q No IYes, ~NO 1 gYes, 0 No IYes, IINo 1Yes. ll No - 2,s 2,s 2L7 gYes, j7No ZYes, ONo Iia ,zYes, q ]No ZYes, q No ! * i’3 lye,. -“- I 295 296 297 298 L . --, ayes, aYes, IIVes, u .~NO ~No g No 299 r / Y e s , g N o I1 I-iNo 8-2 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (243) Area/Office Code Table No. 1 I Code I LocalCall 308 309 No q Yes, q N0 f-JYes. /--JNo 310 ayes, 1 311 1 ayes, 1 312 1 nYes. 3 1 3 1 Ryes, 3 1 4 1 /JYes. I 3 1 5 I IlYes. I Restfictbn aYes. q NO qYes, 0 No 358 q Yes, ONo 359 1[7Yes. 0 N o 1 360 1 q Yes, q No 1 356 357 f-J40 1 ON0 n 0th ON0 Ilk I No II 361 362 1ayes, 1 ONo 1 nNn 1 363 364 365 1aYes. 0 No 1 I IlYes. nNo 399 1 *IYes. nNo I 1 ayes, q No 1 I 321 326 I 330 I I IlYes. 332 1 337 1 IlYes. I n nNo I 343 IFPfes. fltvdl 349 1 nYes: nNo f 8-3 I I I Q -- TOLL RESTRICTION-AREA/OFFICE CODE TABLE (3/8) Area/Office Code Table No. 1 I i __ -.... Code I No. i Local Calr Access Hesrrmon Level !q Yes, NO j q Yes, NO 400 401 4 0 2 / UYes. 0th ,1 403 ! UYes, LNo 1 404 405 / Dyes, al-40 / q Yes, ONo 1 406 407 // Dyes, GNo 1 UYes, UNo 1 408 409 1 UYes, UNo 1 I ! UYes, U No I - - I - . 417 ’ Dyes, Dyes, ONo ONo 418 [7Yes, ,- C]No - / ..~..-Office Code , -Yes, U h 1nYes. c] N,o Yes, UN0 11 453 1 UYes. U N,o I 5 1 454 455 11 11 0 0 w&p/--j 456 . 0457 1UYes, I Yes, 458 II-I I- 459 460 461 462 U No 1 1 UN0 1 Vas I -..IMO I u.--, c]Yes, ON0 q Yes, q N0 n‘-#Yes, --’ ( It40 ‘Yes, OhJo MCI /vat l-IN0 464 U’.--, -..- q Yes, UNo UYes, q No nYes, nNo 413q Yes, DNo 1414 ( UYes, UNo 415 416 - Office Code 410 ’ 411 412 I .^.. 465 466 467 468 q Yes, ONo OYes. Dyes, ON0 [7No Dyes, q lUo f-Jvac ,- l-IF&Y es. U* II -83 =. q * ,I’dS, nN0 OYes, ON0 0 yc- n&I, 84 85 86 87 OYC OY4 gv( OYt V4 8-4 I I I I I 1 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (4/a), A..-+aOffice Z.:de ‘GO. Code Tabis No. 1 Restriction Access Level Lccal Call :-‘du-.n 5.2 1 ;4* _v -q3.4 3 q Yef. 0 No q YSS,[?No q Ys;, q No /--JYEs, q No 534 / q Yes,ONo 555 iq Yss, q No )5636 / q ]Yes, q No Ij507 / q Yes, q No i538/ q Yes..NO~( r i 539 / [7’ r’as. n S+ ace wxe 1 -- e-d- / 1 Code 1 Local Call 1 Restriction 1 Nz:-- ,~I”“‘! 41 II 553 1 UYes, !- UNo 554 UYes. U- No 555 q Yes. ONo 556q Yes. UNo 557 q Yes. 0 No 558 No t j 510 1 q Yes; ZjNo nYes. 1 I 1 q Yes, q No 1 I - , u ---’ u--- I I .6 t I-iYes. nNo I 568 t’es. I 7 f I I 1 iYes; 2jNo 1 I - I 1 UYes. I - UNo I IuYes. I - UNo [ - ,- 1 nyes. nNo I 1 I les. ll 586 7 les, fiNoI 11 599 I nNo 11 5 6 0 I I 5 6 1 Inyes. llN0 I 511 nY;s nNa /’ ~ 7 1 I TOLL RESTRICTION-AREA/OFFICE CODE TABLE (5/e) Area/Office Code Table No. 1 Code No. . 600 / 601 / 602 / 603 604 605 Local Call Access aYes, q No q Ye.s. q No aYes, q No q Ye.s. 0 No ayes, 0 No q Yes, Restriction Level : UYes. 1 IYes. 552 1 IYes, i ;xYes. zr gyes, -r-- j II 1 Ives ZNo NO 1 No INo rNn i No I I I TOLL RESTRICTION-AREA/OFFICE CODE TABLE (643) Area/Office Code Table No. 1 Code I-No. 7fm TOLL CODE TABLE (8/8) _ - - - - RESTRICTION-AREA/OFFICE ;-?a Office Code Table No . 1 3ads ‘JO. 3oc 30’ Lxal Call AC( :ess C’iss * _ q ~ cyss -*I- i w Restriction i -,,. - ; uttce coae : ! Level Code 1 No. !950 ! i 3 0 2 CYSS, g;o / / X3 ’ CYes 304 / EYes 305 CYes 9 0 6 CYes 9 0 7 CYes 908 CYes 9 0 9 EYes I , y3L nr, _-- Local Call 1 Restriction Access nYes. rl\r lures, n.. nNo / _.,. UftlCe Code Level -.a- I I u - 9 1 C 1 CYes 9 1 1 EYes, U'WU , 912 1 EYas -*' ' 9 1 3 CJYes 914 fJYes, UN0 ) 9 1 5 aYes 9 1 6 [?Yes 917 Yes 918 Yes ! 9 1 9 CYes ( 9 2 0 Eyes, i --921 -.,Yes, -. UN0 . 1 q q q / 927 1 EY,,, ! --- -.r UN0 1 m.. 948 1 q Yes, 1 949 1 nYes, n No 1 UN0 I 11 1 Ures, 1 11 999 1 nYes, nNo 1 YYU 8-9 0 UN0 I . TOLL RESTRICTION-AREA/OFFICE CODE TABLE (l/8)I A-a Office Code izble No. 2 E2striction Level Local Call Access ;.;6 e ‘-!o. 23C Eyes, q ]Nc -^I. _/J 222 2.2 2x :iz 207 ryes, ff Yes, Eyes, CYas, 25c 251 252 2 5 3 nNc fjN: 3 NC u N C. 254 CYes, q Nc Eyes, 255 256 257 2 5 8 UNc 1 KYes, q Nc 208 Eyes., q Nc 2% Dyes., q Nc 2:~ Eyes, q Nc 21: Dyes., q Nc 212 ITYes. nNc L I 2131 EYesi q No 21L_ 215 - nN,c 11O_ves, NC I I-iYes. L.--s n u--- 216 1 IlYes. I 232 Illyes. 249 Local Call Access Office Code / I IYes. ~NO : / -Yes. ,j ZYes. ; SYes. / Eyes. i Eyes. CjYes. Eyes. ZYes. ! I -No / ‘ N o j -. NO i ~No 1 JNo ~No :INo ~No 1I 260 259 i-/Yes. 1 1q]Yes. UNo UNo 1 j 261 Dyes. q No /262 nYes. nNo /I 263 loYes. q No 1 I IlNo /I11I 264 265 --- 266 I 282 1 nYes. nNo 1 299 FIN0 I Office Code j I Restriction ! Level 8-10 [OYes, q No 1 1 nYes. nNa u -I I / ;Yes. nNo 1 1 nyes. nNo 1 1 1 I I I I 1 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (2/B) J.--s L.-J.-- IYes, q No IYes. nNo [ ]Yes, 1 INo q Yes, q No nYes. nNo J q Yes,UNo 1 q Yes, 0 No 1 ayes, ONo i ayes, q No ) UYes, UNo 1 “,“J, UN” ayes, q No q Ye.s.ONo ayes. q No ayes. q No 8-11 -a I I TOLL RESTRICTION-AREA/OFFICE CODE TABLE (3/8) Area/Office Code Table No. 2 Cede No. fice Code , u . --I u ..- I Local Call Access Rest r&ion Level Office Code I 467 , u . --1 =iYes. nNo 1 472 I 1Yes. nNo I 476 / 1Ye.s. nNo I I I II l-lye.5 nNo I I- 466 11 491 1ZYes. 492 /nYns I nNo 1 I I I I 11 8-12 -u /lYes. IlNo 1 q No 1 I / 494 1:Yes: , I i=iNo 1 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (4/e) : -ea Office Code Table No. 2 SC2 Local Call .- Access UYes. i N o 503 1 ayes., c No 1 Zods No: Restriction I C”tice Code i Code 1 Local Call 1 Restriction / mz] Level ! ’ SC: q Yes,NO 522 q ]Yes,CNo ayes, q No I/ 553 II 554 1 nYes, nNo 1 5 I/ 555 iYes. ENO i II 556 nYes. nNo - -- 1 557 558 nYes. nNo 3x 1 n’fes, c No 1 SC5 1 fives, ENo 5% Dyes, . flNo 507 508 nYes. r?No 5 5 9 1aYes, E N o Dyes, q No 511 !Yes, q No I IlYes, nN0 5 1 4 EjYes, 515 5 1 6 nYes, nNo 1 517 [7Yes, NO 518 5 1 9 UYes, UNo 520 5 2 1 nYes, nk’522 523 5 2 4 / ayes: ONo 5 2 5 I1nYes. nNo-u --, Y 5 2 6 1nYes, ONo q Yes, NO / I 1 567 aYes. 1 568 Dyes, 5 6 9 UYc 5 7 0 I-JYC I=‘74 l--Iv, q Yes, q No Iayes., q No q No - LS, 0 No 3% C]No 1 [7Yes, q No 1 1 q Yes, q N0 1) 572 8, q N0 8, qn No .I~ 5 2 9 IllYe~‘I, IINO) 530 I q Yes q No 534 535 545 I546 5 4 7 Cb, dyes; IlYes. IlYes. nr’- q /Z 1 q Yes, 0 573 q Yes. 574 q Yes. q No 575 576 nYes. nNo 3/f Ures, UN0 q Yes, ONo 579 q Yes, ONo 5 8 0 I q Yes, q No I 586 I 1 578 0 No , IlNo I u iYes, q No ayes. ONo ak I 1IlYes. nNo 11 596 1 ayes. ONo 1 II cn7 q Yes, q No nYes, nNo I nv- nhj.. I 598 q Yes, 0 599 nYes. ns 8-13 9 .:I 8-14 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (643) At- es/Office Cede Tabls No. 2 =sstrc;ion 1 Code 1 Local Call ACE ss No. / nffirf3 Let. St r&-b : Code Local Call Restriction Level Offir -..a”” Cnr(n “““Z 700 j ZYes. 7No 701 / IYes, 7Na 702 1 IYes, 7 0 3 IYes, 7 0 4 IYes, 705 / Y-Yes, 706 / iYes, /,- ~NG -.tb 7Nc -NQ 7th - 1 755 UYes, UN0 / 756 I 757 1 UYes, / 758 1 UYes, ONo / 7 5 9 1 Dyes, c]No - I 7 0 7 ) iYes, /NQ 1 708 ( Eyes, ~NQ 1 7 0 9 / LYes, INa 1 I q Yes. q No -_. q N0 ,774 775 aYes. I tlYes. IlNo , ... [ 778 U’--, de‘OYes, IIlk - --OYes q- Yes,TJNo q Yes. ANo 1 1 779.I j--JYes 11 780 1UYes IlYes. i-IN0 tt q Yes,UN0 q Yes, aNo - 732 733 11 I FlYes. TIN0 I -----. - q lYes, IIlk IlYes. Ilk40 - --. ---- q Y=. ON0 ..- , q- Yes,Elk 749 11 JYes, 1 It-40 781 t nYes 782 783 rJYes. ON0 1 , q Yes,IJNo 1 1 ~- B , I 1 1 I II I! aYes, q No - - - - 788 789 11 790 11 791 I - - - 1 I II aYes. IYe -.-v , I OYes IlYes 1 797 q Yes q-Yes, --___ ,I IL111 798 799 1 1 IYes, I jNo 1 8-15 , TOLL RESTRICTION-AREA/OFFICE CODE TABLE (7/8) Area/Office Code Table No. 2 1 Code Local Catt / Restriction 0ffic.e co32 Code N o . _ i5 810 -JYes, q No 1 811 :JYes, q No) 812 lYes, nNo ] 813 814 ! gYes, ONo ) 1 8 1 5 ’ TYes. nNo t I]Yes, q No 1 817 ’ ZYes: Local Call - Access - i9 i iiVes. 1 q NO ONo 1 7 86i dyes, q No !I 662 nYes, nNo i( 663 q Yes, q No /I ofid <. 55 ~YCIR u---p nNa UT-- q Yes. q No TlYes. I ~NO 1 ~NO Yes Iu--INa II 76 I ll Yes. n NO I -- a---’ u--- 83 q Yes, ONo fU IlYes. nN0 a41 Office CcAa , - .--. - - - - , nNo 1 660 1 dyes, .- t Restriction Level tlN0 I 8-16 II .. I TOLL RESTRICTION-AREA/OFFICE CODE TABLE (8/8) \ Area/Office Code Table No. 2 1 Code 1 Local Call / Restriction Access / Level Nci / 900 / j?Yes, GNo / go1 1 CjYes, [7No / go2 1aYes, 0 N o i go3 1 Eyes, GNo / InYes. 9 0 7 915 916 nNo/ 1r]Yes. nNo 1 q q 1 Yes, No 1 1 nYes. nNo 1 943 Dyes, q No 1 944 q Yes,rJNa I 945 IlYes. nb T\iL:- ^ p-A- j Restriction Local Call Access ! Level 9 5 3 JYes. ZN0 j 9 5 ’ IYes. ~No 952 : IYes. 7 No 953 1aYes. r No Code N o . - -_ / -.. _ ccc LOO- TOLL RESTRICTION-AREA/OFFICE CODE TABLE (l/8) Area/Office Code Table No. 3 Local Call Code No. Access 200 ayes, c N o 2 0 1 ayes, CNo 202 Restriction C Le”e, I I I q Yes, c No ) 205 , 206 ; 207 q JYes,CNo ayes, aYes, ~No ENo iYes, ~No I : 1 255 I / ( I 256 257 1 A. I 212 213 k 214 ’ 1 217 / 218 222 223 224 225 226 227 241’ 1 262 263 264 q Yes, E No qYes, EN0 11 1 i=iY& i=iNo 1 U.--r Y’-- 1c]Yes, q NO 269 q Yes,ONo q Yes, q No Eyes. ’ Dyes, ayes, IYes, ryes. 267 t -_. 268 270 272 273 274 275 276 fiNo NO ONo ONo nNo [ ayes, q No [ I FlYes. FlNo II 2 4 8 1 EYesi ~No 1 2 4 9 1nYes, nNo 1 F III 1 297 q Yes.ON0 11 2 9 8 q Yes, q No 11 299 nYe.s, nNo I ! 8-l 8 B TOLL RESTRICTION-AREA/OFFICE CODE TABLE (218) . I Area/Office Code Table No. 3 j Code / Local Call ; No. 1 Access ;/ XYJ---1 nYes. - n-No / j 301 aYes, 0 No I 1n3 ~VPC r---lNn / Restriction NIT-- m-2- 11 Code 1 Local Call 1 Restriction UlIKx Lout: Level 11 No. 1 Access Level II 350 I ribs. llr - Jo 1 ^-> 331 352 nrr 1 UYes, r-l.1 UN0 I -.-. - I mice Code I I I 1 1 [2Yes, q No ~]Yes. No -iYes, u0 - No JYes. u N o 1 I 1 q Yes, q No 1 JYes, - UNo - JYes. UNo nYes, n No 1 I 362 363 364 365 ayes, 0 N o 3 6 6 InYes. n N o q Yes, 0 No q Yes, q No =I27 -I r-TS,-0 No J”I I II Fl” 368 369 OYes. 0 No q Yes. ONo q Ye- n kh I ‘3 I ,-.. nYes, q No 1 qYes. q- No - 372 3717 ,a, , , I.” JYes, [7No 1 JYes, [7No 1 - JYes. IJNo 1 1 JYes. UNo 3 7 9 ayes, ONo gYes, q No 1Yes. t-l No . --. I I 1Yes. r--m0 I I d --. - IYes, q No IYes. q - No I L_lYes. UNo 386 387 nYes, 0 No ayes, ONo qYes, ONo IYes. q - No 391 JYes, UNo aYes. ONo 392 q Yes. q No 393 ayes. 0 No 394 q Yes. q No nYes nNn 8-19 I 1 TOLL RESTRICTION-AREA/OFFICECODETABLE(3/8) A-ea/OVce CodE -2s s No. 3 8-20 a TOLL RESTRICTION-AREA/OFFICE CODE TABLE (418) Area/Office Code Tz.jie Code No. 1500 1 q Local Call Access - Yes, L./NC NO. 3 ?estrmon Le>,Sl / Office Code ‘i,“e L~c~~~” I ReLIzp, / O f f i c e lN0 ; 550 rlY0.s. - Ccl=e 1 501 nYes. n --. 1,----. - NC 1 qIYes, q-Nc 502 5 0 3 UYes, 1504 1 , nYes.[ 505 1 506 1 nYes, 507 aYes, 508 Yes. UNc flNc - 1 iYes, q Nc 509 510 511 ’ 514 f” I II 554 555 556 11 558 nlNC UNc nNc q aYes, q Nc Dyes, q Nc ayes, q Nc NC NC ONo 1 nv-- n LIaYes, 1 I I I 560 561 562 II I 1 !563 11 564 II EKE 11 11 No NC : 559 567 568 -. I I I 1 528 1 nYes. n 11 1 531 1 nYes, nl 581 I”” KQ7 ] nYes, ‘es. ‘es, ‘es. ‘es. u #‘es, 1nVes, aNo UN0 ON0 ON0 aNo q N0 ‘es, 0 NC - Cl-T” u’m’, u1.v Ryes, q N0 q Yes, q No 547 548 ) 549 1 nYes, n No 1 595 q Yes. UN0 , r;aF. l-h’nc t-iNn 1 11 597 1 q Yes. ON0 11 598-l q Ye.s.[7No 11 599 1 nYes, nNo ““” I 8-21 ..,v, ..- . TOLL RESTRICTION-AREA/OFFICE CODE TABLE (5/8) . . Area/Office Co& Tk!n ?!c. 2 r&de I Local Call I Restriction No. AUXSS Level 600 ayes, q No I-IVPC 601 i-iNn I T l-lvoc nNn 1 i fmR nNn 1 615 I IlYes. I u . --* 1 1 q Yes. ,- - 622--. 1I 67A “_T “L” nYas nNn 1 u - --’ -. - - u ,cze, 629 can““II I : 1 _“” 636 637 636 UYes, ~NO ayes, I-JNo ayes, No ” 673 ’ 674 =No ‘INo NO NO 677 -8.” I 631 1 q Yes, NO 1~ 632 633 - ..” ayes, pfJn _1.-- 1 nYes, r INo I q Yes, NO , 674 I I q InYes, I nYes. iYe;: 676 ayes, -.- u . --. A. -- I 1 aYes, ~No 1 -,----,- 6%: 1 6G2 I I INo 6E5 6;s 627 -. --. JNO q Yes, q No q Yes. q No aYes, q No 639 aYes, q No 640 q Yes, q No I t nYes, 1No 1 I IlYe 1No i q Yes, JNo i ayes, JNo ’ q Yes, r]No : .653 q Yes, I]No ’ 6Ej 653 &S’ 6I2 ’ INO INo INo 1No iYes, ~No 6~3 q Yes, JNo 1 No aYes, [INO 64!i _ - ,IlYes. -.--, I-JNo 6:-i 6E5 644 646 ) 1 nYes. ----. nNo 3 ~~ 673 6;s JNO r-h ills -. ““) nNn / ii 1 Dyes, 0 No 1 I nYas I IlYes. I ! 671 672 1 ayes, q No j I! RSC; 1 I 669 -__ 1 - .-- -, , -.--a - - --. u. -- r 30 -“! 627 “” 652 ayes. q No 653 q Yes, q No 654 ayes. ONo 655 q Yes. q No I 1 OYes, q No 1 [ 623 1 I 11 I\ ii fj Office Code Level 650 flYes. q No I I U”“’ l-J--- R-in Local Call Access Dyes, JNo UYes, ~NO ES3 q h’es,JNo 6;’ q ]Yes. ?No F’-: <-a C]Yes, ?No -?r nYes, ‘No C-Y? nYes. m N o “7, l-i ‘“-1 L-. I-648 q Yes. NO 649 nYes, p No 8-22 . TOLL RESTRICTION-AREA/OFFICE CODE TABLE (6/8) Area/Office Code Table No. 3 8-23 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (718) Area Office Sodc . __._ ._. _ Lxal C a l l / G SricticCOCk No. 8CC -.- Ccess i c-+s, ONo / --. 1 ;\=E u--- I Level I Orrice Code / Code 1 Local Call 1’ Restriction I N‘T--m-n I wlce Lose 1 1 No. 1.- Access Level I I 1 850 1 UYes. L I TOLL RESTRICTION-AREA/OFFICE CODE TABLE (8/8) Area/Office Cade Table No. 3 947 Dyes, UNo 948 Dyes. 0 No 949 nYes, nNo 996 ayes, p--y 997 ONo q Yes. ONo 998 Dyes, NO 999 nYes, nNo 8-25 . TOLL RESTRICTION-AREA/OFFICE CODE TABLE (l/8)I Area/Office Code Table No. 4 Code No. Local Call Access Restriction Level Office Code / 1 ( A ^^^^^ q Yes,ONo q Yes. q No les. UNo tees, nNo 1 1 [es. n No 280 281 L r 287 1L les. q No (es. 0 No fes. flNu 1-v 247 248 249 fes. ll No 1 ayes. q No q Yes, q No nYes, nNo Ii 8-26 296 297 ayes. 298 Dyes, 299 nYes. I TOLL RESTRICTION-AREA/OFFICE CODE TABLE (218) Area/Office Code Table No. 4 Code No. 300 Local Call Access Eyes, q No 302 1 Dyes, 303 UNo 305 ~NO . Restriction Level ’ ‘Ei$’ Office Code ,,II ‘Od’ No. 11 306 307 313 I ON Eyes, ,- ON - 363 IuYes, . - UN - 357 - ,11 371 1 c]Yf 321 ayes, q No 333 q Yes, q No 334 q Yes, q No q Yes. q No q Yes, q No q Yes. q No 332 335 Eyes, q =Yf 355 q Yes I-IN 356 q Ye-. -.. 1 353 Eyes, q No Eyes, q No - 1 ayes, I - 1 q Yes, UN0 ) I 352 (Eyes, I- q No ‘iYes, 350 UNo 1 - I - 382 383 384 385 IuYc I - I I- 392 u---s 347 348 _-_, u*--.. .-- I --- I --- ayes, q No Eyes, q No .- 1 IlYes. nN I 397 qYf 398 qYc 8-27 Re:Ltyn 1 . Office Code ’ TOLL RESTRICTION-AREA/OFFICE CODE TABLE (3/8) Area/Office Code Table No. 4 [ Code 1 Local Call Gzstriction 406 1 nYes. nNo 406 1 nYes, flNo Code ) 456 413 1 nYes. nNo j 4t5 IllYes; nN0‘ 419 q 420 UNo i No ! 4 3 4 InYes,uN 435 h-b, m-4 I 439 I nw3s. nth I 8-28 Local Call / Gs;triction 1 nff irr TOLL RESTRICTION-AREA/OFFICE CODE TABLE (418) Area/Office Code Table P.3. 4 1 Code No. : 500 501 1 5 0 2 Local Call Axess / nNn i nygj, flNo BYis, ~No - / 1 I RESriCtiOT q ]YES. q No 1 1 503 / ( 504 I q YES. u .No t 505/ q Yis, I-JNo / - q Yes, q No ’ q Yes, ENo q - Yes,-ONo 555 IUYes.\ jNoI ; 5561 q Yes. ONo / I5 571 q -Yes, UNo 1 : 5 581 q Yes, ONo ( / 5 59 1 Dyes, q No 1 I q Ye.s, q No I-lYes. I-iNo INo 514 fives, &E 515 f-JYes, f-JNo 516 nY=. ~No Mficefhdr? -...-- -._-- 5 5 0 UYes, NO / 5 5 1 L.---, 1nYes. nNo u I / 552 5 53 5 54 1 506 11nY&r. n t 5 0 7 / f=JYasl $I I 508 I I-IYSS, r-l N--O 509 Byes, BNo 510 511 Local Call / Restriction Code Level No. .- Access j - r%iyP .-u r.r.40 WV”” ‘Level /No I INo I I / I. / I ., 5 6 0 1 ayes, UNo 1 561 1 -. , I-lYes. Y .--’ nNo u -- t I 6 2 ,, 1 nYes. 1 5-, ~~, LnNo , 5 6 3 InYes,nNo) 56 4 UYes. UNo ! 5 1, 1; - Ii 65 q -.Yes. ONo 5 6 6 IUYes. UNo 1 5 ‘67 1 ayes, .- q- No 1 5 6 8 .1 UYes. ,69 1 UYes. UNo UNo 1 1 ‘71 1 UYes. ,74 1UYes. UN0 I - ;76 1 UYes. UN0 aI.. UNo 1 -__ I 1 I 1 I I I ! -1 I I I I 523 I 77 1 q Yes. 0th I I 530 I fly=. r 83 a--- , 1No 1 UYes. I i87 q Yes, q N0 1 q Yes. q No 1 1 UYes. I 547 UN0 i84 q- Yes. -. q NO II IN0 I I Ilk. n 8-29 UNo 1 I II I I I 1 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (518) Area/Office Code Table NO. 4 Call j 1 Code N o . j1 Local Access Dyes, UNo 600 Restriction Level pu:-- +-A^ / [ Code 1 Local Call / JIIIc;t: c/uue / 1 No. ! Access 601 -’ ayes, 0 No 602 -. /-IYes, n N o 603 &s, @Jo ( 604 nYes. nNo 1 605 606 ’ TIN0 I C]Yes, ONo aYes. DNo 2 aYes, UNo 1aYes, 1 660 661 ] ayes. 1 ayes, Yes, {Yes. ONo ONo nNo ~NO q Yes. q No aYes. UNo - I tl Yes. n NO , u---r Y 1nYes. IlNo Office Code q No aYes. ONo q ]Yes. ONo Dyes, q No c]Yes, q No ayes, q No aYes, UNo * Eyes: fi No ilk., 650 651 6 5 1 653 1 654 655 656 Restriction Level L 672 673 674 675 682 ! TOLL RESTRICTION-AREA/OFFICE CODE TABLE (6/8) Area/Office Code Table No. 4 Local Call CCdde PGO. Restriction Level - ~faess -.. 7 0 Office Code I - I 1 - 1 6 ‘2 J IN0 1 jres. 1 J I - ,- ‘6 q Yes, fiNo 7Dyes. q No FT.. -.. 4 1 UYeS. - 1 Ures. UNO 1 Ryes. I I I I \No 1 q Yes. q No 1 747 748 /-JYes, q Yes. q No 798 q Yes. q No 799 nNo nYes, 797 ONo q Yes, q No 749 nYes, nNo a-31 . TOLL RESTRICTION-AREA/OFFICE CODE TABLE (7/e) Area/Office Code Table No. 4 Restriction I eve1 1 Code 1Local Ca;; / Restriction / Mficp Cndn 11 Code 1 Local Call ccess / ; Office Code 11 653 1 @Yes, 0 No 805 1 UYes, 855 - 1 UYes, I -.. 859 .1 q Yes, - L -- - 820 Dyes. CNo 821 q Yes. CNo I 822 1 UYes, -LNo 1 I-~ c.. I 8 2 3 UYes, L:No 8 2 4 (7Yes, NO 8 2 5 Dyes, ENo 8 2 6 ayes, ENo I8 2 7 1 UYes. I - - -- 869 Dyes, q No ayes. CNo 870 871 --- I aYes. ONo Dyes, UNo -.. rlN0 11I a72 1 UYes, - - - m.. 873 Ures, u N o 874 q Ye.s. q No a75 876 LNo I q Yes, q No q Ye.s. q No i--fNo . 884 q Yes, DNo 1 u---s Y--- 890 ayes, ONo IlYes. nN0 .844 1 aYes. - 845 q Yes. 846 nYes. II 847 I aYes. 848 q Yes, 849 nYes, . - -, ~ - q No 1 q No 1 nNa 1 . - [jNo q No NO 891 I iYe: nYe$ 11. 894 i, ONo 11 895 1 ayes, ONo 11 896 1 i-tYe= I-IN~ 897 ayes, q No 898 ayes, ONo I”, a 9 9 , . ..P I nw 8-32 .@ . TOLL RESTRICTION~AREA/OFFICE CODE TABLE (8i8) Arez Offics Zode Tzzie Uo. 4 NC 9c-‘ 9C’ zcess ievei 3 q Nc c. ss, q NC C ‘35 ~-1 “‘I 11 951 I 1Yes. - --, f--iNo u. -- 1 r . GS. nNc I I I 952 IYes, 0 No i3 gYes. 17 NO ii4 UYes, UNo 955 aYes, ONo 956 95 i7 r . 5s. n No II q Yes, q No /1 958 1 aYes, 1 IIVes. 959 960 1iAYes. 1 nYns 0 No 1 n No 1 U No nNn 1 I 9,. . ‘4 a - - I ‘9 InYes, q- No 1 I- i’bs: [ ;No i 945 9.46 947 943 949 UYes. UNo aYes, q- No - 997 942 I 944 943 1nYes, 1ayes. nNo ONo 1 - 964 I 11 E?‘es, GNo 1 Eyes. nNo 1 aYes, q No ayes. NO ! n Yes, f-/No 1 -@a I I UNo 1 f-‘Na i I I 9L , - . --, - . -- , 996 No 1 _- 1 nYes. ___, n .-37 1 nYes. nNa 1 I 993 994 95. 998 999 8-33 t1UYes, nYes. -.--, l--JYes, uq No-nYes. n No I I 1 .I 1 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (l/8) A-2aOffice Code Table No. 5 Lsde j Local Call 1 Restriction Level I nYes. ll No 1 .UYes, UNo 2'37 7.’ A“:-* “I I Ilrl: P,-.Ar UUUF! 250 251 257 258 228 ,ayes, q - No -d 9 ( UYes, UNo 1 / fr4 ( q Yes, q No t .I 1 Ryes. nNo Code No. 8-34 Local Call Access ayes, q No Restriction Level Office Code I UYes, L ayes. q I- No 1 TOLLRESTRICTION-AREA/OFFiCECODETABLE(2/8) Area/Office Coce Table No. 5 I 1 q Ye@ 317 318 . /l\, 8 -e 'e-e ’ ‘--%s. .c ““3 386 l-/No ‘8 ‘e‘8 ‘8‘8u re! nYe! f-iNn -: R= 8L, 8s. U.-w, -...P r-lklr I I --- I ONo q No 1 nves. ll No ,-.8S, J NO a-35 I I I 1 TOLLRESTRICTION-AREA/OFFICECODETABLE(3/8) Area/Office Czde Table No. 5 J;re prrAr\ 11 Code 1 Local Call 1 Restriction 1 nffir0 ~“~c uuuc 1 v”‘b= 11 ;xj / 1 402 I 403 t 404 , 405 406 407 Arrocs 1 I R/PI 1 452 fiYes 1OYes 340 TNo I i IlYe; i7 No i j q Yer ~No I1 455 456 457 458 t i f-tNo - .-.c, 470 InYes. 471 -..v UNo 1 q Yes, q No tl Yes. n 476 NO u ‘--’ U’” llyes. ~NO 1 q Yes, q No q Yes. (-JNo 1 nNn 1 8-36 I I rr 1 8 udael TOLLRESTRICTION-AREA/OFFlCECODETABLE(4/8) Area/Office Code Table No. 5 ReSriction Code Local Call L?,/ei No. /- Access 550 j UYes, UNo 1 II --. , u .--’ / Office Code / I 562 1 nYes. nNo 1 563 1 Dyes, q No 1 __- ,---’ ,- 1 519 /--JYes. ON0 1 520 q Yes, ONo 1 521 nYes. nNo I I I - 1569 UNo 1 570 571 1UYes, UNo 1 1IlYes. nNo 1 SAA I, u. I IYnn INa II --, Iu.-- II SAQ I --- 8-37 I 1nYns nNo 1 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (543) Area/OK,ce Code Table No. 5 8-38 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (64 A-GalOffice C:I:e Table No. 5 LOG 3311 I Restriction 1Yer -31 709 70 711 712 ! 713 / 714 I 715 j 716 : ,,; _ No aYes iJYes C]Yes T]Yes FlYes / I It-40 INo -No -No IJYes nYes :No J I 720 760 761 762 763 ayes, ONo nYes. nYes, nNo nNo - q Yes. NO IfJYes, I1 IlYes. I II I ! 11 11 11 =No I 1 1 1 UYes, q No 1 11 764 11 7 6 5 11I I 7 6 6 767 I -No I ,i=iYes 7 1 8 i IYes uilce Lose : 758 1 q Yes, nNo - -- - i f, -. I___ 759 UYes. 0 No / 1 ;y,; zf.& 1 Restriction No I - : : hll.-- booe A-A_ I/ Code 1 Local Call unce I [Yes; ON01 nNo 1 fi No I ! I j 719 / q Yes ZN , iUYes ?NoI 724 726 t 731 f flYes. ?N I iiYes. iN . -- , 736 (aYes. 7th 1 .- 1737 Y.--‘ --I--- I I~YesJNoI .1 7 3 8 (UYes. ANo 1 1 7 37409 1 nYes. TN I 1 1 i%s. irE I t t 741 # IiiYes. 7% L 1 786 1 iYes; ,7 8 7 1UYes. 788 1’ u -Yes, I fiNo 1r UN0 ON0 11 789 1 q Yes, aNo II 790 I q Yes. ON0 I II 8-39 791 I FiYes. ll II 4 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (7/Q Area/Office Code Table No. 5 1 Code 1 Local Call 1 Restrict~c n No. Access Level 8 0 0 IJYes, ON0 801 ayes, q No __ __ .-e&n 1 i Coce 1 Local Call ] -’ Le V”“t: 1 NC Access ;L 852 Eyes. ~NO 65’ Eyes. ~No 8 5 2 Eyes. IaNo 1 -INo 809 1 q Yes, q No 810 1ayes, q No 1 1 8 1 1 I 1 nYes. nNo 812 1 :Yes: ENo -. 827 1 ayes, UNo - 8-40 9 Restriction Level “f~IbG Affixn u,vue P-A- I TOLL RESTRICTION-AREA/OFFICE CODE TABLE (843) \ I Area/Office Cods Table No 5 8-41 TOLLRESTRICTION-AREA/OFFICECODETABLE(1/8) Area/Office Cade Table Yo. F; 8-42 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (2/B) Area/Office COCG Table No. 6 Local 5.31 Restriction Code Acce~ No. 300 CYes, 1 No 301 CYes, 7 No 302 Eyes, 1 No 303 ryes. 1 No 3 0 4 1-. I-Yes. .-No 1 305 Eyes., 1 No ;;“7 E;;;, 1 No Local Call Code No. Access 350 OYes, E No 351 : ayes, Et-40 352 ayes, c No 353 j aYes. E No 354 i IxYes. ~No 355 j [7Yes, E No 356 / aYes. q No 357 / c]Yes, m No 358 / q Yes. c No Office Code Level ,7No No No No i 3 1 2 1 f=Yes. I ) 313 1 LYes, i 314 1ryes, 360 361 362 363 364 365 366 --No -No -No 1 ~NO 1 I No 1 I 11 II 1 ayes, m No ayes, ~NO nYes, ri No I i UYes, L iNo I I C/Yes, C jN0 1 1aYes, [ I nYes. 369 1UYes, L 370 IL 371 IlYes. I r 328 i 330 I q Yes, Ll 1 3 3 4 I- - Office Code 1 I 359 / c]Yes. GNo 319 320 1L1Yes, ~NO i I Restriction Level I IuYes, !JNo 1 No I 336 1 iZjYes; fjNo I ’ -TjYes. DNo 385 ayes, q No II 3 8 6 Dyes, ONo 387 I ITlYes, II I TOLL RESTRICTION-AREA/OFFICE CODE TABLE (3/8) Area/Office Code Table No. 6 Local Call i-Yes. ~NO Eyes. ONo Eyes. [7No nv,, I-lL1, UYeS. UN0 aYes. q N0 3 u’--’U‘-- q Yes,ONo q N0 nN0 .--, .-rJYe% c3M q N0 8-44 Restriction I TOLL RESTRICTION-AREA!OFFICE Area/Office Code Table No. 6 1 Code 1 Local Call 1 Restriction 1 NI:,, ,---1WllILt: LwJt: Level 1 No. 1 Access CODE TABLE (418) Co& 1 Locca Call ] Restriction 1 IsI xz-- ~_J. i UIIIL~ Lose / Level No 1 Accsss I I 503 5 0 4 505 506 507 508 509 5 1 0 511 EN0 Byes, ONo .aYes, ~.~o 552 552 5% 555 55.5 557 556 550 ryes. =jNo IYes. JNo Eyes. JNo ryes. 1No ryes. lb40 , ryes. ~No Eyes. II]No ryes. 56G Eyes, JNo 5 6 : Eyes. JNo 5 6 2 ryes. NO 5 6 3 Eyes. ~NO 5W Eyes. JNo q Yes, q No nYes, 2jYes, nNo BNo Dyes, q No ayes, 0 No Dyes, ONo ayes, q No 5 1 2 513 nYes, nNo Dyes, q No 514 q Yes, [ZJNo 522 523 aYes, j I j ONo q Yes, q No g5- .-nv~ti. f-m 5-16 : c]Yes, q No ( 524 -- 527 572 573 574 Jr40 Eyes. UNo Dyes. ~No Dyes. ~NO u ---9 u.-- I / 575 iTYes. NO /576 EYei: ENo nYes. I nN0 i I 577 591 IlYes. nNo TOLL RESTRICTION-AREA/OFFICE CODE TABLE (518) Arez Office Zcde TaL 3 Kz. 6 / / 1 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (6/8) Area/Office Code Table No. 6 Local Call ,- Access - me c;oae 759 1 UYes. I - _-. , U.--r u--- 7 6 2 Office Lose Levs UNo 1 I I nNo 1 nYes. 7 6 3 764 Restricxn 1 q Yes, NO i 777 783 - - W’“’ U“- i nYes. I u---s 746 746 747 748 749 q Yes, q No q Yes,[7No q Yes, q No q Yes, q No nYes, nNo 7QS . -- IYes I I 1 799 8-47 1 nYes, I INa I , Iu IYes. INa II . --’ Iu.-1 nYes. 1 I . -_ _-, I 797.1 ayes, -q No 1 7 9 8 1 UYes, UNo 1 796 1 I nNa UNo - - I 1 Dyes. DNo t-t No 1 nNo II I I 1 ! I 1 .@ . TOLL RESTRICTION-AREA/OFFICE CODE TABLE (7/8) Area/Office Code Table No. 6 808 c]Yes, [7No 809 q Yes, 0 No 810 Dyes, q No 8 1 1I nY- f-‘Nn 812 813 814 fiY-, , , . .- 8’15 l--iYiW nu.-No I , u .--’ Dyes, q No q Yes, NO I r-h. n NO I es, q No 1 I I I II 8% ,1IlYes. nNo IJYes. -1 (7No !! 857 !- 8-48 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (8/8) Area/Office Code No. -.. 900 901 902 90: $ Cots Table No. 6 Local CGl Acce 5.5 -.. Restriction : Office Code Level -;Yes, _ No 1 - ]Yes. _ No ( I ZYes, g No iYes, _ N o Eyes, 7 No 9a4 /,JYes, 1 No -_- i I 906 r?Yes. -No .= / 907 i aYes, -No I 908 / I--1 Yes. -No 905 1 1I ) I 1 I 1 j 909 ; aYes. f N o i 9 1 0 i QYes, INO 1 9 1 1 i aYes. ~NO r 1 912 , r/Yes, - N o 1 Yes. - N o I 1 913 914 DYesi ENo 1 915 iciYes, - N o 1 ;I; ;;s, ~No es. -No 9 1 8 Dyes, LNo 919 c ]Yes, z N o ) 920 c ]Yes, ~NO 1 921 ayes, c N o 1 922 nYf3s. FNo I -No 1I 923 cIYes. , _ 924 Dyes, r No 1 / j Code Local Call No. Access --- r-l.. jc I I I 930 q Yes, ENo 9 3 1 nYes, NO IYes. r No I 937 q Ye.s.ENo 938 aYes, ENo 939 OYes. NO 940 nYes. r[No IYes, l7No 1 8-49 Restriction Level Office Code TOLL RESTRICTION-AREA/OFFICE CODE TABLE (l/8) Area/Office Code Tale No. 7 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (2/8) Area/Office Code Table No. 7 8-51 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (318) 8-52 34 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (418) Area/Office Code No. i Code Table No. 7 -LEi;” 1 Local Call Access q Yes. C f-40 ayes, C N.0 -. q Yes,c N.o nyes. r-No 1 q Yes. I 3 t Eyes, ON: 570 571 11 523 524 s.?R nYes No u---vl-l Y.-- ayes. q No , nYes. u .--. I-iNo u.-- I 4 q q 572 InYes. r?No 1 574 575 576 577 578 Dyes. no OYes, DNo q Yes, NO 579.-ayes, 0th 580 Ryes, q No 5 8 1 nYes, NO 5 8 2 ayes, NO 5-~~ 83 nYes. r/No I 1 584 t 585 I IlYes. nN0 I 15 UYes, UN0 Yes, N0 q Yes. NO q Yes, NO 5 2 6 nYes, nNo ’ 527 HYes, NO 528 ayes, q No I 529 q Yes, ONo 530 ayes, q No 531 nYes, nNo 532 q Yes, ONo 1 568 5 1 9 1nYes. flNc 520 521 nYes, n No q Yes, q No q Ye.s. q No 525q Yes. NO (-Jffjpe P -.-_ q Yes, 0th 569 ayes, El40 7 --522 1 ----. \Yes. fiNo - 1 z2striction Level 2 8-53 I . I TOLL RESTRICTION-AREA/OFFICE CODE TABLE (98) Area/Office Cot? Table No. 7 8-54 TOLLRESTRICTION-AREA/OFFICE CODETABLE(618) . Area/Office Cede Table No. 7 Code I Loca: Call ACE ss No. / 700/ q ]Yes. ?No 701 1 aYes. ?No Restriction Level 7 0 2 j nYes. ?No 703 1Byes. NO 704 1nYes. ?No No 707 708 --. I >- --. ,z -z, - -i --- 2.3 , 7-s --- :-3 , --a /x is’: 73 --/- -3 7% 75 1 752 TZJ I 1 I I/ 1 BYes. NO ) nYes. NO 1 1 No-- i-~ I 7 1 2 \Yes. =jNo 713 aYes. JNo 714 ayes, JNo 715 nYes. 1No No 721 Office Code ‘lz” I ,I I 754 755 --a 170 -9~;. Call ACE:? ss ~~ - /es - Yes - fes ZYes ZYes IYes ZYes. =Yes. Yes Eyes. - Y e s IYes. -Yes ZYes. -Yes. IYes. -Yes. ~NO 3Nc Z]No ~No ~No ~NO JNo JNo I 1No ~No . JNo ~No ! ~No I ~Nc / ~No ; DNo ! nNo I I 1 :Yes: ! 723 728 1 7 3 5 I.nYes. I 745 I nyes. ll 749 1 nYes. nNo 1 nNo 1 8-55 .a Restriction Level Office Code TOLLRESTRICTION-AREA/OFFICECODETABLE(7/8) Area/Office Code Table No. 7 TOLL RESTRICTION-AREA/OFFICECODETABLE(8/8) Arsa/O?ice Code Table No. 7 I c-ode 300 Local Call ( Restriction ( rur:3e Code Code Local Call Access Level N o . _ Access IYes, 7 No 1) 950 1UYes, u No ) 301 1Yes. VO. ’ 910 911 7 No IYes, ~NO 1 1Yes. 1No 1 951 11nYes. u --. nNo I 1 L--- i2 I llyes. nNo 8 II I IYna Restriction Level Office Co”Kle ’ I I INn I I I I I 11 960 1 q Yes, q No 1 11 961 1nYes. n No 1 i4 (q i6 Yes, UNO 1 ayes, A - UNO I - 7 I I IYes. I INo I i8 ‘0 UYes. I UNo I I /” ‘2 1UYes, UNo 1 I ,U.--7 u.-- , 1nYes. nNo 1 I I I4 IuYes. UNo 1 I 18 1UYes. U No I I I I IllYes. I I ,- 8-57 I iiN I r-m0 I I TOLL RESTRICTION-AREA/OFFICE CODE TABLE (118) Area/Office Code Table No. 8 Code Local Call No. Access - Restriction Level Code Office Code I q lYes, q N0 1 211 212 IaYes, 1 nVas I L 227 228 I .--, q n nNn 1 .-- 11 I II ) UYes, UNo 1 261 1 [7Yes, ONo 1 262 1 ~VPC n Nn ..- 1 263 U’” Dyes, q No q Yes. ONo nNo 1 237 238 239 q Yes, ONo ayes, q No q Ye.s. q No 287 288 240 nVns ~NO u. --. u. _- 290 289 I nYes. i7r-h s, I 1 ;Yes.~. ,246 ayes, 247 q Yes, 248 q Yes, 249 nYes, 245 q No nNo q ]No q No q No nNo 1 I 277 1 278 ayes, ONo 279 280 IlYes. r-h0 , u---v - - - I1 nYes. -nNo , 1 ayes. ONo 1 - .““) - ayes, q No 1 Dyes, q No 1 1 c]Yes, q No 1 r 229 1 ^ -1 ^ 260 NoI nNo t Local Call 296 297 298 I 11 8-58 u” 299 1 nYL”, , ,.-- , I I TOLL RESTRICTION-AREA/OFFICE CODE TABLE (2i8) AreaDiice Code Table No. 8 Local C& Restriction Code Access Level No. i Code No. Office Code q No q Yes. DNo JYes, C N o 300 TYes, C Nu 30f 3 0 2 ?Yes. r N o 303 =jYesl EN0 1 304 ?Yes, i-No 1 30-5. iYes- rNa 1 306 307 306 309 310 311 2 ?YeiT-F No I1. TYes: ‘?No 1 3 Yes, c No 3Yes. CNoZYes, i7Yes. -1.--r - I I I L -- , Restriction i w.ce C-4e Level I ’ “- 350 Dyes. 351 3 5 2 nYes. i-!No 353 fiYes.l ENo I II 354 flYes, i--iNo 11 3 --5 5 , -t iiYes. --. -tiNo I 1 nNo 1 I11 I 3 5 6 1nYes. I iI 3 5 7 u 1 i=iYes: .-i=iNo 358 359 I Dyes. q No aYes, q No CNo no 7Yes. rN0 I Local Call Access 360 361 --. 362 I ayes, ONo t--iYes. nNa --. 1nYes. nNo / 1 , 1 32 1 2 fjYes. Ties. EN0 rt40 11 II 336 iq Yes, C i NO 337 : i aYes, ayes, q Yes, OYes, 1 Dyes, 349 1 nYes. 345 346 347 348 371 372 IrlYes. NO 386 387 q No q No q No q No NO 395 mYas, 396 ayes. 397 Dyes, 398 q Yes. 399 llw3s. 8-59 1ayes, nN0 ONo 1 ayes, q- No .- [7No ONo ONo 0 No nNo , 8-60 TOLL RESTRICTION-AREA/OFFICE CODE TABLE (418) Area/Office Code Table No. 8 1 Code 1 Local Call / Restriction Level 1 No. 1 Access / 500 1 nYes, NO 1 Yes, ~1 No 501 ’ 502 Dyes, NO 1 / 503 504 ( UYes, UNo 1 5Q5. ] ayes, 0 Na. .I. fi n / q Yes, -0 No 1 I 515 1 526 527 I llyes, ll q k, q Yes, q Yes, q- Yes, I-528 534 535 1 ayes, q ]No 1 I 537 Inyes. I 539 I I I30 I nh, n InYes. nNo l AI‘:^^ r ^A^ UIIlLkZ e Jut: COE : Local Call 1 Restriction Level NC j Access 55: ! ayes, ENo 55' j ayes, ENo 552 55: 55' 5Yes. @No 5 5 5 aYes, ~NO 5 5 5 ayes, ON0 1 q Yes, NO / q Yes, pb& -I:^^ P--lWI I ILe LUUt: 8-62 TOLL RESTRICTtON-AREA/OFFICE CODE TABLE (6/8) Area/Office C-zde Table No. 8 ’ Code Locr gYis : 700 701 C]Yes ! 702 nk Call - /JYes Code Local Call [ Restriction 1nu:-r. -^A- --- lb&2 he: 1 711 ma-A - Pa,- JNc JNC ~ 703 DYE iNc j 704 nYes ?Nc /-_ 5. NC i 706 nYer 1Nc 1 707 BYer ~Nc j 708 nYer ~Nc j 709 DYer ~NO / / Restn~ion - 752 --. j 11 / 1 ] 1 1 -‘Yes. ’ u--- 1 753 754 IYes. nNo I 755 ?Yes, nNo 1 756 757 IYes, f--JNo 1 7 5 8 I_]Yes, UNo 1 7 5 9 AYes, UNo ] I i nNo Y ZYes. q NO I 1 ,IYes, - q No1 I JNo 761 1 IYan I INa I I I I I iili u.-- 715 .- ‘IlYe: -.-- 716 ‘nYer t 717 I iTYes 1 718 i [7Yes I 719 d“- , lN0 II 2 - 1No =iNo ~No I1 II 1 7 7 6 4 ayes. ~NO 1 7 6 5 ‘1Yes. l-IN0 1 766 IAYes. UNo 1 3 - 6. 7 I IYas~ -. L .--. I Y-TINn I I I 7 6 8 ayes. ONo 7 6 9 ayes, DNo i nYer ;1No / 776 iiYes. Y -I nNo i I 731 I 17 3 2 1nYec nNo 733 734 735 I 736 FiYes EUci t I I _ 7 737 738 If-JYes. 739 I IlYen TIN0 I or40 ] q Yer ON0 7 4 7 Irlm. nHol 4 8 fiYes. I=&0 7 4 9 nYes. II?40 . ) 787 ; UYes, UNo 1 I 7~13 . -- :nYns u ---’ nNa I1 u--- 1 nYes. nNa 1 I 1 I[ 7 9 7 ( Dyes. ONo 11 7 9 8 I Dyes, ONo 1) 799 / n Yes, nNo 8-63 1 i -. TOLL RESTRICTION-AREA/OFFICE CODE TABLE (7/8) Area/Office Code Tab. Nc 8 1 Code 1 Local Ca I ! =~S;*‘~:iion icc3l Ca Ni ^^ /-^A^ C o d e : Restrbzon I Tu6:-, ~-~. j q ]Yes, c ‘40 800 8 0 1 1ayes, c No 802 Yes, / - / q c No --- II , ,A0 RR6 IYCS I RR7 IYm I ,%cl I IYes I ,No I IYes. I Nol IYe% I ,Na - I II RRR 3s. n No II 89A II A95 - - @xi 1 1 1 8-W I lYer I D C I I ! I 1 L A7A 0 No i-iNn 845 8 4 6 1nYes. nNo 1 847 ayes, DNo 848 ayes, ONo 849 nYes. nNo _‘--’ - 897 898 899 i I 4 .--’ L - I I I I II .I I I i I ,_IYes, ZYes. ?Yes. LNO CNo rN0 . TOLL RESTRICTION-AREA/OFFICE CODE TABLE (818) Area/Office Code Tab:e No. 8 L o c a l 1 Code I Access Gail / ?estristion 1n‘4:r T P -A^ (I Code "I I be uuuc ! NO. 400 501 902 Eyes, L t:o i ryes, r t43 j FYes, C tie 1 503 904 905 Eyes, Et40 ! ryes. r-t40 I fjYes. 5 t40 / No. Le\J?l Restriction ~~~~~ 950 :]Yes. q No 951 n - NoF’JYes, 0 No ,lYes. - --, 952 953 954 gYes. ONo ayes. q ]No 955 Dyes, q No 956 ayes, q No 957 c]Yes. q No 958 ayes, q No 959 aYes, 0 No I 907 Eyes, ENo 908 Dyes, c No 909 EYes, E No 9 1 0 Local Call / Access OYes, ENo 1 911 I 913 967 917 / [?Yes, E No 1 iq ‘feS, 11 9 6 8 II 969 i aYes, NO 970 j Dyes, ONo 971 972 973 I tl’fes. nNo I II 980 9 2 0 DYes. Eiz 1 921 922 ayes, /-JNo q Yes, ONo 928 1nYes. i nYes, nNo 1 iaYes, q No 1 q Yes, ONo r 1 OYes. q No 1 II 989 II 990 I IlYes. rho I 1 942 I 947 Illyes. Tit-40 I 948 9 4 9 PYes, [?No q Yes, q No ayes. q No 9 9 9 8-65 nYes. nNo , i: A“:^- f.-. / Vat%- bGZ2 j I ! II ! I TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table Ns. - (01 to 64) - 2 Hum-ed (230 to 249) 12 Hundred (223 to 249) i I 600 i 700 I EX 19 1 1 20 21 1 2 2 123) I I I I I I 1 : 1 29 I ISOI i 46 47 48 - 49 I I I I I j 200 it30 69 1 11 70 / II 71 ! (1 72 / 1) 73 ) I 79 I 11 I 300 80 96 97 98 99 1 I 8-66 ) 1 400 I 500 600 I 700 800 I I ! I I I I I I / 900 I TOLLRESTRICTION-OFFICECODETABLE Office Code Table No.- (01 to 6~ 7 2Huncred (230to 249) L . 00 01 1200 1300 I4OC : 50@ 1600 / 7oc 1 I I 1 I -2 Hundred (200:: 249) ?X 900 I/ ,/ 200 r 50 51 09 10 11 59 60 61 41 42 43 44 45 46 47 48 49 91 92 93 .94 95 96 97 98 99 I . 1 300 400 /500 I 5.20 I 700 I300 '9cz I I I I . . 8-67 TOLL RESTRICTION-OFFICE CODE TABLE Office Ccce Ta; 5 No. - (01 to 64) - 2 - . -drec :200 3 249) r----- 2 Hundred(200 to 249) TOLL RESTRICTION-OFFICE CODE TABLE Office Code Tab:2 No.- ic- to fLi - 2 I+,-dred (20: :z 1’9) - 2 k--ndrec 8-59 :200 to 2~3 TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No. -(C- 13 64) - 2 H,-dred ZIOto 5:; 200 , , 300, L30 5,:~: 6:l: 2 Hundred(200to co Cf 700 800 900 50 51 (200 ; ! c2 52 j 24 25 26 : 3 74 75 76 27 ! 77 I 88 308 ,400 , I 500 2dS, 600 700 800 900 I 1 .. i 40 I 1 ! 1 46 I I 49 1 I 1 39 I ! 1 II891 1 I i I II I I I I I I 11 8-70 98 99 I I I I I II I 1 J ) I TOLL RESTRICTION-OFFICE CODE TABLE OfficE Code Tzzie No.- (01 to 64) 8-71 TOLL RESTRICTION-OFFICE CODE TABLE Office Cute Table No.- (01 to 64) - 2 Hundred (200to 249) 120; t -2H,-drew. (2OC:: 249) 300 '400 1500 1600 1 700 800 ) 900 !m I I I I I II 1.20 99 300 I 30 I 500 5:c) I - 110 I 330 ) 900 I . 8-72 TOLL RESTRICTION-OFFICE CODE TABLE Office Code TaS’e No.__ (01 to 64) 2 H,-dred (2OOto 249) 00 /200 1300 1 G O / 500 r 2 Hundred (200to 249) I600 1 J700 !800 1900 jj 1200 I I/ 50 I/ 04 54 05 06 07 55 56 57 13 14 15 _ 52 1 I 26 27 28 29 30 46 47 48 49 11 I I , I ! / 63 64 65 ! 3 0 0 400 1500 ] 1600 j 700 1800 1900 / 1 I I 1 1 76 77 78 79 80 96 97 98 99 , I . 8-73 TOLL RESTRICTION-OFFICE CODE TABLE Off& ,C;sde -zzAe No.- (01 to 64) - 2 Hundred (2Xto 2r9) -- 1 i 0: I ~~ 5OC / '600; 700 1800 I I I 02 03 I I 05 06 07 08 ! i 1 1 ) 1 ! I 09 10 11 12 13 I I I I I cn I ( ' : ! I 1, ' 59 60 I ! I !' 1 61 62 63 64 I I 65 fxi I1,1 98 99 I I I200 I300 / 400 I I 51 52 53 55 56 57 58 I 1 530 I 1 15 ,c 48 49 ,----2 Hundrec (2OOto 249) L 500 1600 1 7C3 / 806 1900 I I I I I I I I ! I 1 1 , I I , 1 I I i I I I I I I I I I . TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No.- (01 to 64) ,--- 2 Hundred (200 to 249) 7 2 Hundred (200 to 249) 8-75 TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No. - (01 to 64j i 2 Hundred (200 to 249) 7 2 Hundred (200 to 249) i 1 49 I I I II 99 I I I I I . 8-76 TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No. - (C’ to 64) ,----- 2 Hundred 1200to 2L9) : 200 300 400 500 6:: 730 / 800 200 800 900 j 00 50 01 51 , i !I- 80 1 36 37 ’ 9.:) 2 Hundred (205 XJ 249) I 30C ' 400 500 600 700 1 I t I I I 11 43 44 45 46 47 48 49 86 87 93 94 95 96 97 98 99 8-77 1 1 I I 1 f i I I I I . I . TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No. __ (01 to 64) 2 Hundred (200 to 249) - 2 tiundred (200 to 219) 8-78 TOLL RESTRICTION-OFFICE CODE TABLE Ztiics Code Table No.- (01 to 64) 43 44 45 46 47 48 49 93 94 95 96 97 96 99 . 8-79 TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No. - (01 to 64) - 2 Hundred (2OOto 249) -2Hundred(200to 249) I. 00. 01 02 : 03 04 I200 1300 / 400 500 I600 I 700 _, 800 900 1 I ! I I / 11 1 1 I II 1 i ! 11 i 0 6 ' 07 I , I I I I 1 I 1 I 400 I 500 1600 i 700 800 900~ / I I ! I 1 1 I I ! I I I I 7Q I I I ! j 65 I 300 56 57 58 I I 15 200 50 51 52 53 54 1 i I I I I I I I I I TOLL RESTRICTION-OFFICE CODE TABLE Office Code TX e No.- (Cl to EL) - 2 -,-dred(200tc 249) 2 0 0 33: co 5 0 0 j ECIO 701 9:: 7 2 Hundred (200to 249) / 2 0 0 3 0 0 400 500 600 700 900 I 00 32 04 05 06 I1 49 t /I11 I I I I 55 32 54 55 56 900 l I II 8-81 99 ! I t t I 1 I i 800 50 c’t I t I I I . TOLL RESTRICTION-OFFICE CODE TABLE Office Code TX e iYz .- (01 to 64) - 2 -,ndr+z (200to 249) 2oc 130: COG 500 /Soot 700 18100 00 08 09 _ L 11 12 13 14 15 16 I- 2 Hundred '2QOto 249) ! / / 11 I 1 I 1 35 36 1 1 I 48 49 1 I I I I I I I I I I I I200 i 300 T400 152 JI ( 600 1 700 1800 I900 900 11 58 59 ( 1 61 62 63 64 65 66 1 1 I I I I. 11 II 8-82 98 99 1 I 1 I I I I I I I I I I . TOLL RESTRICTION-OFFICE CODE TABLE Office Code Tabk No.- (01 to 64) ;- 2 HL--zred (200 to 249) ,---- 2 Hundred (200 to 249) r 8-83 TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No. - (01 to 64) - 2 Hundred(200to249) -2 Hundred (200 :o 249) 200 I 00 ! 01 ' 02 i 03 300 400 500 600 1 700 800 900 I ! 11 II / 06 1 07 / 08 I 09 / 10 I 11 1 12 t [ 15 I 16 17 18 19 1 20 1 1 21 1 22 t 1 23 1 1 24 1 I I ! I ! I 11 ! 1 I , I / r t i r I ! I ! 11 11 11 11 8-84 50 51 52 53 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 /200 I ! j ! 300 400 500 600 1 700 800 1900 I / j / / ! 1 1 j * I ! I 1 I 1 1 1 I I ! 4 I I ! I I I I TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No.- (01 to 64) - 2 Hundred (200to 249) I200 1300 1400 i 500 1600 1700 1800 1 C~Z~Z /I , I i I j L 7 2 Hundred(200to 249) / zoo 1300 1400 1500 !600 1 700 1 800 1900 ] 01 02 03 04 ES52 53 51 43 44 45 46 47 48 49 93 94 95 96 97 ?a 99 . TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No.- (01 to 64) T----- '2 Hundred (200tra 249) / 2491 2Hundr ed (2ooto . 1 200 300 400 500 600 800 700 900 200 00 01 06 07 ( I I I I I I I ! 11 56 ) II 57 I 09 10 11 12 59 60 61 62 30 31 32 79 80 81 82 48 49 300 I400 I I 50 51 1 1 I I I I I I 11 II 98 99 / I I I 500 I600 I I I 700 / 800 I I I 900 I I I I I I I . 8-86 TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No. __ (01 to 64) -_ - - 7 A 8-89 7d9) TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No .- (01 to 64) - 2 Hundred (200 to 249) I 2 Hundred (200 to 249) I L 200 300 400 500 600 700 I800 I 00 01 18 19 20 21 22 23 24 25 I I I I I 11 II 69 70 1 I I 11 72 73 1 I I II I I I I I I I I I I I I I I I I I I I , 46 47 48 49 11 95 It 98 99 11 96 ~1 II 8-90 I 1 1 I I I I I I I I I I I I I I TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No .- (01 to 64) I2 Hundred (200 to 249) 11 8-91 61 I I I I I I TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No .- (01 to 64) 2 Hundred (200 ts 249) 41 42 I A? I I I 2 Hundred (200 to 249) I I I I I I I I I I I I 92 I 1 I JJ 11 99 I I I I I I I I I I 8-92 1 TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No .- (01 to 64) - 2 Hundred (200 to 249) - 2 Hundred (200 to 249) A L 200 300 400 500 600 700 800 200 900 50 00 01 51 8-93 300 400 500 600 700 800 900 TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No .- (01 to 64) ,--- 2 Hundred (200 to 249) - 2 Hundred (200 to 249) L 1 2 0 0 I300 1 4 0 0 1 5 0 0 1 6 0 0 1 700 , 42 1 43 1 I I I I I I 11 8-94 92 93 1 I I I I I I TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No.-(Ol to 64) - 2 Hundred (200 to 249) 00 01 02 03 /200 /330 j 400 ; 500 j / I I ! ,------ 2 Hundred (200 to 249) j 600 1 700 1 800 1 900 11 I1 I 1 1 8-95 L 50 51 52 53 1 200 1300 1 400 1 500 !600 1 700 1 800 1 900 I I I , TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No.- (01 to 64) 8-96 TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No.- (01 to 64) 72 Hundred (200 to 249) 2 0 0 3 0 0 4 0 05 0 0 600 1 700 800 900 200 50 00 01 2 Hundred 300 (200 to 249) i ! 4 0 0 5 0 0 6 0 0 ! 700 I 800 j 900 ; I 51 I I I I I II 8-97 99 I I I I I I I I I i I TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No. __ (01 to 64) 2 Hundred(200to 249 07 08 09 10 . 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 11 11 81 a2 a3 a4 a5 86 a7 88 a9 90 91 92 93 94 95 96 97 98 99 I 1 1 1 1 .. 57 5a-. 59 60 I I I I 8-98 I I 1 I I I I I 4 TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No .- (01 to 64) ,------2Hundred(200to249) 07 08 1 1 1091 10 11 12 13 14 15 16 17 18 19 20 21 22 [ I I I -2Hundred (200to 249) I 11 1 I I I I I I 11 11 ! 60 61 62 63 64 6 1 1 5 66 67 68 69 70 71 72 25 8-99 ’ ’ ’ r- I I I I I I I TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No .- (01 to 64) - 2 Hundred (200 to 249) 7 2 Hundred (2X to 249) 1 200 I300 1 400 1 500 1 600 1 700 1 I 19 20 69 70 71 72 21 -- I 80 81 82 83 I 31 32 33 1 38 39 40 41 42 1 1 I 1 43 45 46 47 1 1 1 ,48 II 49 I I I I I 11 I I I I I I 11 ! ! I ! 1 11 11 I I I 11 I 44 1 I 1 I !. ! I I I I I I I I I I I I I 11 II 11 11 ! I 11 11 11 8-100 88 89 90 91 92 93 94 95 96 97 98 99 -; 1 1 1 1 I 1 1 1 1 1 1 I I I I I I I I I I I I I I I ! ! I I I I ! I I I I I I I I I I I ! I ! I I I I 3 ! I r I I I I I TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No. - (01 to 64) .- 2 Hundred !ZWto 2c9) i 2CO 00 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 330 : 4 0 0 j 500 I / i 600 ! 7 00 I 7 2Hundred(200to I200 1300 I400 I50 10 1600 1 700 1800 1900 I800 1900 11 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 _. I 8-101 249) I TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No .- (01 to 64) r--- 2 Hundred (200 to 249) 7 2 Hundred (200 to 249) 1. 1500 ISOOI 7 0 0 1 8 0 0 190011 8-102 1 2 0 0 I300 I400 1 5 0 0 1 6 0 0 1 7 0 0 1 8 0 0 1 9 0 0 I I I I TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No.- (01 to 64) 1 08 1 19 I 28 29 1 I 1 32 33 34 35 36 37 38 39 40 41 42 43 44 I45 46 47 48 49 I 1 I I I I I I I I I I I I I I I I ! 11 11 68 69 11 78 79 . 1 1 ! 1 ! 1 I 1 1 ! ! 11 1 1 11 I 8-105 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 I 1 1 1 1 I I I I I I I I I I 1 I I I ) 1 j 1 I 4 I ! ! 1 ! ! 1 1 ! 1 1 1 1 ! 1 I I , I TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No .-(01 to 64) 2 Hundred(200to 1200 1300 1400 1500 y-2 Hundred i2OOto249) 249) 1600 1 700 I800 ! 900 21 22 23 -24 25 26 I I 28 29 30 31 32 1 1 33 1 34 ( I35 1 36 _ 37 38 39 40 41 42 43 44 45 46 A7 . . 48 49 1 I 1 I 1 1 I 1 ! I 1 I ! ! 1 1 I I I I ! ! ! 1 I I I I ! I ! I I ! :200 j 300 I 4 0 0 / 500 1 6 0 0 1 700 1 800 1 900 1 71 72 73 74 11 II 76 1 77 I 78 79 80 al a2 I _. I[ )I a3 ) 11 a4 1 I[ a5 1 11 86 II a7 11 88 11 89 90 11 91 11 92 93 94 95 96 97 e, 98 99 8-106 I I 1 I I I I I I ! ! I 1 1 1 I I ! 1 ! I I I ] 1 -1 --I 1 I I 1 I I I I I I I I I 1 I I - I 1 TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No .- (01 to 64) - 2 Hmdred (2OOto 249) I 2 Hundred (200to 249 !200 / 300 I 400 01 / 02 03 f I I 05 06 . 07 1 1 09 1 I 1 15 I 1 1 18 19 20 21 22 23 24 25 < I I t I I I II 53 I I I ! I I I i I I II 57 I 65 1 I I I I / I 68 69 70 1 1 I I I I I I I 72 73 11 74 II 75 I ] 84 I45 ._ 46 47 48 49 I 1 I I I I 1 I t I I I I I I I I 96 97 98 99 .- 8-107 TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No .- (01 to 64) - 2 Hundred (200to 249) .i 96 97 98 99 46 47 48 49 8-108 TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No.- (01 to 64) - 2 Hundred(2OOto r , 249) 2 Hundred(200to249) 230 300 : 400 [ 500 I600 1 700 1800 I900 11 I200 1300 I400 I500 I600 1 700 I800 1900 1 05 06 07 55 56 57 09 10 11 12 I 59 60 61 62 33 I 83 34 35 36 84 85 86 8-109 I I I TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No.- (01 to 64) -_ 2 Hundred (2CO to 249) ,----- 2 Hundred (200 to 249) 1 200 00 01 02 03 j I 04 / 05 / 400 300 500 I I 600 I I 700 800 j 23C 1 3 0 0 j 4 0 0 1 500 1 600 ! 700 50: ; j I j 900 11 II 11 11 8-110 51 i 52 53 54 55 1 I / ( - - t -I - - t I ! I I 800 I ! ! ! I 900 TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No. - (01 to 64) - 2 Hundred (200 to 249) 1 03 04 05 06 07 j 1 1 1 I 08 1 [ 09 1 2 Hundred (200 to 249) ! 1 ( I I I I ! ! I I 1 I I I I I 11 II 11 (1 53 54 55 56 57 58 59 I 1 1 1 1 1 I ! -. 1 I I ! ! I I ! I 37 38 39 40 41 42 43 44 a7 aa a9 90 91 92 93 94 45 46 95 96 I 47 48 97 98 99 I 49 8-l 11 I I I I I TOLL RESTRICTION-OFFICE CODE TABLE Office Code Table No.- (01 to 64) - 2 Hundred(200to 249) -2 Hti@red (200!3 249) I. 1200 1300 1400 1500 I600 1 700 1 01 02 03 04 05 06 07 08 I 800 /900 11 ! II 51 52 53 54 55 56 57 58 11 59 I 1 1 48 49 11 I I 1200 ;300 . . 29 I 30 31 32 33 34 35 36 37 38 I I 81 82 83 84 85 86 87 88 I 8-129 TOLL RESTRICTION-711 0 DIGIT TOLL RESTRICTION TABLE I Entry No. 01 Set Data Default Value Entry N o . ------- blank 33 Set Data 1 Default I / Vaice blank 02 34 ------- 03 35 __----- 04 36 _------ 05 37 __----- 06 38 07 __----- 08 _------ 39 _--e-w- 40 ------------- 09 _------ 41 10 ------- 42 11 ------- 43 __----- 12 44 _------ 13 45 ------- 14 46 __----- 15 __----- 47 __----- 16 __----- 48 _---v-w 17 _------ 49 18 __----- 50 19 __----- 51 __----- 20 __----- 52 _------ 21 53 _------ 22 54 _------ 23 55 _------ 24 56 __----- 25 57 __----- 26 58 __----- 27 59 ---e--v 28 ------- 60 __----- 29 ------- 61 ---_--- 30 _------ 62 ------- 31 ------- 63 32 _------ 64 8-130 __----- : j 9. Automatic Route Selection t[ I( AUTOMATIC ROUTE SELECTION-LEADING DIGIT TABLE (1 n) Entry No. 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 Se. lata oc AC - - - - Default AC oc blanl blad Entry i Set Data 1 Default 1 N o ./ AC i OC /AC jOC i 2441 - - - - b l a n k i blank Se AC ( I 241 242 243 --- 244 --_i 245 -- 285 246 -- 286 247 -- 287 248 -- 288 249 -- 289 250 -- 290 251 -- 291 252 -- 292 253 -- 293 254 -- 294 255 -- 295 256 -- 296 257 -- 297 258 -- 298 259 -- 260 -- 300 261 -- 301 262 -- 302 263 -- 303 264 -- 265 -- 266 -- 306 267 -- 307 268 -- 308 269 -- 309 270 -- 310 271 -- 311 272 -- 312 273 -- 313 274 -- 314 275 -- 315 276 -- 316 277 -- 317 278 -- 318 279 -- 319 l 9-l - ---_ -_ -_ -_ -_ -_ --. -. -_ -_ ------ lata Default oc :AC 3E blani - i - I . . _ _ - AUTOMATIC ROUTE SELECTION-LEADING DIGIT TABLE (2/7) -IEntry Set lata De wit 3try Set lata De - yDefault - . - - -: N o . A C o c A C oc o c AC No. AC AC ; OC 1 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 - - - - blank blank 360 361 362 363 364 365 366 367 368 369 370 371 372 373 - 374 375 376 377 378 379 380 381 382 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 - - -- dank -- 401 -- 402 -- 403 -- 404 -- 405 -- 406 -- 407 -- 408 -- 409 -- 410 -- 411 -- 412 -- 413 -- 414 -- 415 -- 416 -- 417 -- 418 -- 419 -- 420 -- 421 -- 422 -- 423 -- 424 -- 425 -- 426 -- 427 -- 428 -- 429 -- 430 -- 431 -- 432 -- 433 --- 435 -- 436 -- 437 --9-2 _ _ - - _ -- i _ - - --_ b;an; Sank ’ AUTOMATIC ROUTE SELECTION-LEADING DIGIT TABLE (5/7) j Entry’ Set &:a DefaL:t Entry Set C lata -C tult ---l-I Entr Set Data T C tult / No. --~AC GC oc 1- - AC OC No. I AC A( oc No AC oc A( O( blan 76C - - da1 - - - - - blar blar 721 --- - -761 - - - 682 722 762 --- - - -- - 683 -. -. 723 76z - - -- - 684 - -- -724 -- - -_ 764 - - - 685 -- -725 -- - 765 - - - 686 -- I -726 -- - 766 - -- - 687 ---1 -727 -- 767 - -- - 688 -- -728 -- 768 - -- - 689 -- -729 -- 769 - -- . - 690 -- -730 -- 770 - -- _ - 691 -- -731 771 -- - -- - - 692 -- -732 772 --- - -- - - 693 -- -733 773 --- - -- _ - 694 -- -734 774 --_ - -- - - 695 -- -735 775 --- - -- - - 696 -- -736 --- . 776 - -- _ - 697 -- -737 777 --_ . - -- - - 698 -- -738 778 --. _ - -- -- 699 -- -739 779 --- - -_ -- 700 -- -740 --- 780 - -_ -- 701 741 -- -781 --_ - -. -- 702 -- -742 782 --_ - -- - 703 -- -743 783 -- - -- - 704 744 -- --- - 784 - -- - 705 -- -745 -- - 785 - -- - 706 746 -- -786 -- - - -- - 707 747 -- -787 -- - - - - 708 -- -748 -- - 788 - - - 709 -- -749 -- - 789 - - - 710 750 -- --- - 790 - - - 711 751 -- -791 -- - - - - 712 -- -752 -- - 792 - - -- 713 753 -- -793 -- - - - -- 714 754 -- -794 -- - - - - - 715 755 -- -795 -- - - - - - 716 -- -756 796 -- - - - - - 717 -- -757 797 -- - - - - - '18 -- -758 798 -- - - - - - 719 759 -- --799 -- - - - - - I 9-5 AUTOMATIC ROUTE SELECTION-LEADING DIGIT TABLE (617) I Default intry Set lata De, ult Intry Set Data ’ Default ’ (En:rv ~Set Data OC i AC I OC / No.’ AC oc ACOOC AC No. A C o c A C oc No. -, f 800 - - dank Aank -- - dank dank 840 - - -841 88' 801 - - -- 842 ,, 882 802 -- - -- - I 863 843 803 - - -- 884 804 844 -- - -- - 885 845 805 -- - - -- 886 846 806 -- - -- - 887 807 847 - -- - -- 888 846 808 -- - - -- 889 809 849 -- - -- 890 850 810 -- - -- - 891 851 811 -- - - -- 892 852 812 -- -- - - 893 813 -- 853 - -- - 894 -- - 854 814 -- 895 -- - 855 815 -- 896 -- - 856 816 -- 897 -- - 817 -- 857 898 -- - 818 -- 856 899 -- - 859 819 -- 900 -- - 860 820 -- 901 861 821 -- - -- - 902 -- - 822 -- 862 903 -- - 863 823 -- 864 904 -- - 824 -- 905 -- - 865 825 -- 906 -- - 866 826 -- 867 907 -- - 827 -- 908 -- - 868 828 -- 909 -- - 869 829 -- 870 910 -- - 830 -- 911 871 831 -- - -- - 912 -- - 872 832 -- 873 913 -- - 833 -- 914 -- - 874 834 -- 915 -- - 835 -- 875 916 -- - 876 636 -- 917 -- - 877 837 -- 918 -- - 838 -- 878 919 -- - 839 -- 879 : t'ank 1 9-6 b!ar.T MQ - - AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Cede Table No. __ (01 to 32) -~- !?Pls: - Default Value Set Data Area C;.Ze - / ~~ Route ?lart TaSie - - (3 digits: 200 to 999, or blank) 01 - (2digits:Olto 32) - . :203 1300 I400 1500 / I . I I is I .I 15 I I I t 17 / 18 19 20 21 22 23 I I 1 32 1 II I I II II I 50 1200 j 300 / 400 ) 500 1600 t 700 1 800 1900 ] I is I 11 67 68 69 70 71 72 73 I 11 82 / /600/ 7001800 190011 II I I It I I I I II _ I I I I I i - 2 Hundred(250to 299) -- 2 Hundred (200to 249) 00 blank I I 46 47 48 49 is 96 97 98 99 9-9 I I I I I I I I I 1 AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No. ___ (01 to 32) Item _.-~ Default VaiLe - -. Set Data Area Code - I Route Plan Table - - (3 digits: 200 to 999, or blank) bia-. c: _ - - - - - . - _ -I -2 Hundred (250 tc 299) - - (2 digits: 01 to 32) - 2 Hundred (200 to 249) 200 00 300 400 500 6 0 0 7 0 0 1800 1900]1 Cl I I 02 f-n “W ! I I ( I I I I I I I I I I I 1 04 05 06 i 3Q ! 11 50 11 11 11 51 52 53 54 55 II 7Q I I I I I I I I - I 200 I 300 I 400 _ 500 1 1 1 1 1 I I 600 700 I : 800 I I 1 900 I ! I I I I I I I I I I AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No. __ (01 to 32) Item i-I Default Value Set Data Area Code ;-.--- (3 digits: 200 to 999, or blank) Route Plan Table i (2diglts.01 to32) 01 ,---- 2 Hundred (200 to 249) 7 2 Hundred (250 to 299) 1 2 0 0 , I300 1I 4 0 0 1 5 0 0 1 6 0 0 ( 7 04 05 06 07 i I I I 54 55 56 AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No.- (01 to 32) I Set Data Area Code --- (3 digits: 200 to 999. or blank) Route Plan Table - 17 18 19 I I I I 67 68 69 I ! I” , 25 74 75 1 1 I 76 76 I I I ;; I 01 - (2 digits: 01 to 32) I Default Value I i AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No .- (01 to 32) item Set Data Default Value 200 blank Area Code --- (3 digits: Route Plan Table (2 to 999, or blank) - digits: 01 to 32) 01 r 2 Hundred (200 to 249) r 2 Hundred (250 to 299) 18 19 20 68 69 70 21 71 30 31 I I I I 80 81 47 48 _ 97 98 99 49 9-15 I I I AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No .- (01 to 32) I Set Data Route Plan Table - (2 digits: 01 to 32) - I I 2 Hundred (200 to 249) 1 20 LL 23 24 25 26 27 28 33 I I 1 ! ! I ! I ! I I I I I I 34 I 35 I 36 37 38 39 40 41 42 43 ed (250 to 299) I ! I II 1 1 I I II 1 I I I I 8 1 I I I I 1 I I, 71 I 11 IZ I II I If I II I I I ( 11 II ,,II 73 74 7c; S” 1 I ,I II 76 I I I II I I I I I II I I I II I I I I I I I I I I 78 79 II I1 I II I 45 II 11 II ii I I II I I I L 46 47 49 I --- (3 digits: 200 to 999, or blank) Area Code I Default Value II I I I I 11 83 1 II I I Ad II 11 I II 11 II II I II I 11 I 86 87 RR 1) 89 1 I II II I I I II IL II I ii [ 90 91 97 -- I 1 II 1 I II I I , II I I I I I I I I 93 ,I , I 95 I II 97 I I II 99 -- I I II 9-16 1 If I ( I I I I I 96 -- I I II I I I I I I I II I 1 I I I II II I / I I I 1 AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No.- (01 to 32) item I Default Value Set Data Area Code --- (3 digits: 200 to 999, or blank) Route Plan Table -- (2 digits: 01 to 32) .- , 13 I I I I I I I I I I I II I II I ii I I I I I I I I I AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No.__ (01 to 32) _____--__. Iterr. .--. - - - -___ Default Value Set Data Area Cot? blank - (3 digits: 200 to 999, or blank) ____ Route Phn Table (2 digits: 01 to 32) 01 L e . - - . - . - -- 2 Hundred (200 to 249) - 2 Hundred (250 to 299) IO 1 800 1 900 11 I .3l-i I I I I I I I I I I 200 I 300 I 400 II 52 EQ ( I II fn I 24 74 75 39 40 41 89 90 91 92 A7 I 47 48 49 97 98 99 9-18 I I I I I I I I I I I AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No. - (01 to 32) Item Default Value Set Data Area Code - Route Plan Table - - (3 digits: 200 to 999, or blank) - (2 digits: 01 to 32) 1 I - 2 Hundred (200 to 249) I I 1 I I I I 2 Hundred (250 to 299) I I I II c.3 I 11 82 1 I I I I I I Ii A3 47 48 49 97 98 99 9-19 I I I I I I I I I I I i AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No.- (01 to 32) I Set Data II Area Code - Route Plan Table - - - blank (3 digits: 200 to 999. or blank) - (2 digits: 01 to 32) 01 - 2 Hundred (200 to 249) I - 2 Hundred (250 to 299) 1 200 I300 1 400 1 500 1 600 1 700 1 81 DO I900 I I I II 1 2 0 0 I300 1 4 0 0 1 5 0 0 1 6 0 0 1 7 0 0 1 8 0 0 1 9 0 0 50 -I I 1 00 t 32 I 1 I I I I I I I II ii I I 39 I I I I I I I I II a9 I I I t _Al. 42 43 1 ,I I I I I I I II 91 -. I I I 1 1 I 92 93 94 II 99 44 [ 49 I, 1 [ I I I I I I Default Value I 9-20 I I I I I I I I I I I I I I I I I I I I 1 1 I 1 I I I I I I I I 1 AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No .- (01 to 32) I Set Data Area Code -- Route Plan Table - ,----2 Hundred(200to I 1 1 t 00 01 02 03 AR - (3 digits:200to i QR I blank -2 Hundred (25Oto 299) 50 51 52 53 I I I 01 249) I I 999, or blank) - (2 digits:01 to 32) 1200 1300 I400 t 500 1600 [ 700 1801 3 I900 II [ I I II I I I II I I I 11 I 1) I Default Value I I I II 9-21 1200 1300 1400 I500 I600 1 700 I800 I900 ) 1 I 1 1 I ! 1 I I I I I I I I I I 1 I I AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No.- (01 to 32) 1 Default Set Data Area Code - Route Plan Table - - - - (3 digits: 200 to 999, or blank) 00 t as L / 1 200 I 300 I I I I 400 I 500 I E ;OO I 01 I I I I I 2 Hundred 700 I 800 I I 900 I 49 50 II 86 87 88 89 ! 99 1 9-22 (250 to 299) 1 2 0 0 1300 1 400 1 500 1 6 0 0 1 700 1 8 0 0 1 900 1 11 37 38 39 1 blank d i g(2i t s : 01 to 32) -2 Hundred (200 to 249) \ Value I I I I I I I I I I I I 1 I 1 AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No .- (01 to 32) Item Default Value Set Data (3 digits: 200 to 999, or blank) Area Code - Route Plan Table -- (2 digits: 01 to 32) - - 01 2 Hundred (200 to 249) , 2 Hundred (250 to 299) l-m -1% 1200 ~300~400~500 ~600~700~800~900~~ I I I “3 , I I I 04 I I I I 19 I I I I I I I I I I I I I I I I 11 I I ,, I I II I I I I I I I I I I I I I I I I I I 1 I I I 54 55 56 I .- I I I 05 06 12 blank 62 1 69 I I AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No .- (01 to 32) Item I Area Default Value Set Data Code --- (3 digits: 200 to 999. or blank) Route Plan Table - (2 digits: 01 to 32) I -2 Hundred (200 to 249) I 2 Hundred (250 to 299) 500 160017001800 19001[ .- , I I 11 I I I 22 23 1 1 29 30 31 -29 ;; 1 I ) III I I II I II I I I I I I I I I I I I 1 I I I I I I I I I I I I I 01 I200 I300 I400 I500 I600 1 700 I800 I I II s; I II 72 73 ) 1 11 11 11 II 79 1 80 1 81 1 82 1 83 I I I I 1900 1 AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No .- (01 to 32) item D e f a u l t Vaic;e i ! Set Data AreaCode - Route Plan Table - - - (3 digits: 200 to 999, or blank) - (2 digits: 01 to 32) I 7 2 Hundred (200 to 249) 200 . 1 11 t 40 I I I I I I I I I I 01 I 2 Hundred (250 to 299) 4f301500 i600~700)800~900~~ 300 00 01 blank 1 I I I t 11 11 11 50 51 52 11 61 11 II 9-25 1200 I300 1400 I500 I600 1 700 I800 1900 I 1 1 89 1 90 I I I I 1I I 1 I I I I I I I I I I I AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No.- (01 to 32) Item Default Value Set Data AreaCode - - - Route Plan Table (2 digits: 01 to 32) ( 3 d i g i t s : 200 iO 999. C* >:~~icb -~ .-+ 2y.L-j ,------ 2 Hundred (200 to 249) I 1 00 01 02 24 1200 I 76. 1 I 7Q 1 5627 )300~400~500~j600t700 1 I I I I I 2 Hundred (25: !a 299) 800 I900 11 II II I \I I I I I I I 50 51 52 1200 I I 1 1300 1400 1500 ! ! I I I I I II ;s I 78 I I is77 I 1600 [ 700 1800 1900 I , I I I I I I I L ;i ;ii 80 81 30 31 I 9-26 I AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No .- (01 to 32) r / Item i Area C m e -~- Route Plan Tabie Default Value Set Data (3 digits: 200 to 999, or blank) - (2 digits: 01 to 32) - 01 - 2 Hundred (200 to 249) I 09 1 I I I blank - 2 Hundred (250 to 299) I I 11 11 58 59 I 1 I I I I I I AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No .- (01 to 32) Default Value Set Data Area Code - Route Plan Table - - - (3 digits: 200 to 999, or blank I - (2 digits: 01 to 32) 2 Hundred (200 to 249) 01800 1900 11 blank I 2 Hundred (250 to 299) I 200 I 300 I4 31 1 AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Cw!e Table No. - (01 to 32) item --- Route Plan Table - I 300 blank - - (2 digits: 01 to 32) 01 2 Hundred (200 to 249) 200 . Default Value I --- (3 digits: 200 to 999, or blank) 1Area Code 00 01 I Set Data 400 1 500 ! 600 700 I I -2 Hundred (250 to 299) 8 0 0 ! 9 0 0 ]I II I II 50 61 I 200 I 300 I 400 I 500 I I I I I 600 700 800 900 I AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No.- (01 to 32) Item ._ Set Data Area Code 1 Route Plan Table - - I-- ( 2 - __ : Defa;,Ptalue (3 digits: 200 TO 999. CT Sank I digits: 01 to 32) 01 I - 2 Hundred (200 to 249) j 00 15 16 17 j 1 200 I300 1 400 1 500 1 600 1 700 1 800 1 9 0 0 1 j I I[ 2 Hundred (250 to 299) 50 65 66 67 1 2 0 0 13 0 0 j 4 0 0 1 5 0 0 1 6 0 0 1 7 0 0 1 8 0 0 1 900 I I II 3 AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No .- (01 to 32) Itern I Set Data I / Area Ccc? - - - (3 digits: 200 to 999, or blank) Route ?lan Tabie - (2 digits: 01 to 32) ; 2 Hundred (200 to 249) I Defaur1 1 1 ! 200 t 300 I 400 i 500 i 600 1700 1f blank 01 - 2 Hundred (250 to 299) AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No .- (01 to 32) Set Da:a ~- Default Value (3 dggits: 230 to 999. or Sank. blank Item Area Code - Route Plan Table - - - I - (2 digits: 01 to 32) I- 2 Hundred (200 to 249) - 2 Hundred (250 to 299) I200 1300 ! 400 ; I800 1900]/ I 17 I I I I I I I I II 22 23 24 75 01 ii7 72 73 74 7s I 9-36 I I I I I I I I I I UTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No. __ (01 to 32) item Default Value Set Data Area Code - Route P!at: Table - - (3 digits: 200 to 999, or blank) - (2 digits: 01 to 32) - 2 Hundred (200 to 249) I f-m I I I 2 Hundred (250 to 299) I I I I I I I I I I II 11 I/ 61 cc) 17 18 67 68 19 69 1 36 I I blank I II is 1 I I I I I I I I I I I I I I I I I I I I I I I I AUTOMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No.- (01 to 32) I item Area Code - Route Plan Table - I ,--. I Set Data - Default Value 3 dgits: 2CO to 999. or blank) (2 diaits: 01 to 32) ” j200 ~300~4001500 is .I1 I 17 I- -I I I I I I I I I 2 Hundred (250 to 299) 16001700[800 I I I I I I I 01 II 2 Hundred (200 to 249) L blank I I I 1900 11 II I 11 I I 50 51 ! 2 0 0 I300 I400 I500 I600 1 i‘00 I I I I I I I ! ~~ II 67 I II sa I I I I I I 900 800 ! I I I v I - t - i , 84 85 35 -. 36 R7 86 9-38 AUTQMATIC ROUTE SELECTION-OFFICE CODE TABLES Office Code Table No.- (01 to 32) Item Default Value Set Data Area Code - Route Plan Table - - - - (2 digits: 01 to 32) 01 7 2 Hundred (200 to 249) - 2 Hundred (250 to 299) L 200 1 : 300 400 500 600 L 700 800 900 200 00 01 300 400 500 600 700 800 900 I 50 51 I QA 49 blank (3 digits: 200 to 999, or blank) I I I I I I I Ii 99 I 9-39 I I I I I I I I I I i I I AUTOMATIC ROUTE SELECTION-ROUTE PLAN TABLES (116) ?oute P l a n S t a r t H o u r Table No. Hour AM/PM Route List Number I MON. j T U E . W E D . T H U . --CAM.CPM--~-01 @AM, CPM FRI. --j-v - -----; I--.--- - ----~AMOPM --i--i--- - - SAT. - - __- - - __- - SUN. - -__ - - - - - - -- q q 02 AMOPM----I-- -- __- -- -II CAM, P M -- -- -- -- -- -- -- - - • A M u P M - - __- _- - - - - - - .-m-m.[7AMe~PM - - --I-.--- - - - - - - - ~~~AM.~PM - - -__ __- - - - - - - - - __- - - - - - - - - - - - - - - - • A M . f l P M 03 - - -w~AM,~PM - - - - - - - - - - - - - -- q AMDPM ~- -- -- -- -- -- ---- q AMOPM -- -- -- -- -- -- -- 04 05 06 -...vm~AMv~PM q t&t, P M -----~AMvOPM -mnAM,nPM ----- ----- -~ ---- ----- ----- ----- ----- --uAMnPM -- q AMvuPM -- flAf4Of-J -- q AMOPM ----- ----- --__ --- ----- ----- ----- ----- -- q AMOPM -- -- __- q AM.OPM -- -- -~ -- q AM.OPM -- -- --- -- --q AMXl’M ----- ----2 ----- ----- I Note: Selection of value Default value Start Hour blank, 2 digits (01 to 12), AM/PM blank Route List Number blank, 2 digits (01 to 64) blank 9-40 Route list number corresponding to the appointed time must be set up. No blanks should be appointed in the Route list. When blank is set up, all that line have to be . blank. l l AUTOMATIC ROUTE SELECTION-ROUTE PLAN TABLES (216) Stat-l Hour LRoute Plan Table No. 07 Hour /AM/PM - - t~AM,OPM - - - MON. TUE. 1 Route List Number THU. FRI. WED. SAT. SUN. -- -- -- - - - - -- -- -- - - - - - nAM,OPM -- -- -- - - - - OPM -- -- -- - - - - q [1.7AM, AM,[rlPM - - i. -- -- -- -- -08 -- -- -- -- --- -- -- -- -- - -. jtyv q PM- - 09 10 11 12 ----- I nAM.OPM -[IIAMOPM -q AMOPM - UAM.OPM - - -- -- -- -- -- -- -- -- -- --- -- -- -- --- -- -- -- --- -- -- -- -- __ - OAMOPM C%M, OPM -- nAM.C]PM --- r]AM.OPM - ----- nAM C]PM -C]AM.flPM - LlAM, OPM -aAM, c]PM -- ----- q AM.&M DAM. q PM -( :jAM, q PM -~M.OPM/-- -- -- -- --- -- -- --- -- -- --- -- -- -- -- -- -- -- --- -- -- -- --- -- -- -- --- -- -- -- -- -- -- -- --- -- -- --- -- -- --- -- -- -- 9-41 AUTOMATIC ROUTE SELECTION-ROUTE PLAN TABLES (316) Route List Number Start Hour / Route Plan T , Table No. H o u r hM/PM ; F,1CN. T U E . W E D . _-___--- :-IAM.-:PM; - - I-- 13 _ _ _ -. _--- - __ [7AMGPM Ii -- q AM, q PM THU. FRI. SAT. SUN. -- -- -- -- -- -- --- -- -- -- -- -- ~- -- -- -- -- -- -- -- -14 -- -- -- -- -- --- -- -- -- -- --- -- -- -- -- -- 15 16 UPM I q AM. q PfiJl q AM, - - q AMOPM -- OAM, q PM -- - q M~CIPM q P M I q AM, -- -- -- -- -- --- -- -- -- -- --- -- -- -- -- --- -- -- -- -- -- -- -- -- -- -- --- -- -- -- -- --- -- -- -- -- -- --- -- -- -- -- -- -- 17 - - q AMuPM -- q AM,OPM -- q )AM q PM -- q AM. q PM -- 0AM UPM 18 -- 0AM, q PM -- DAM, [7PM -- 0AM q PM -- -- -- -- -- --- -- -- -- -- -- --- -- -- -.- -- -- --- -- -- -- -- -- -- ~- -- -- -- -- -- --- -- -- -- -- -- --- -- -- -- -- -- --- -- -- -- -- -- 9-42 AUTOMATIC ROUTE SELECTION-ROUTE PLAN TABLES (416) Start Hour Route Plar ’ Table No. 19 20 21 22 23 24 Hour AM/PM - - - - - - - - DAM. q PM flAM, q PM q AM. q PM DAM. q PM - - q AM.C]PM q DAM. P M - q AM.DPM -- q AM, q PM --A --- MON. TUE. q AM.OPM /J~~,OPM’ q AM. q PM q AM. q PM WED. THU. FRI. SAT. SUN. -- - - - - - - -- - - - - - - - -- - - - - - -- - - - - - - - - -- - - -- -- -- -- -- - - --_ -- -- -- -- - -- - - --. -- -- --_ - --_ -- -- --. DAM. q PM -thA q PM --. DAM. DPM -DAM, q PM -- q AM.DPM q q AM. P M - - q AMC]PM -- CM4 CPM ----- Route List Number - - - -- -- -- -- - --. . -- -- --. -- --. . -- -- --. -- - - --. . -- -- --. -- --. . -- -- --. -- - -- -- --. . -- -- --. --- -- --_ -- -- --_ --- -- --_ -- -- -- --- -- --_ -- -- -- -- -- -- -- -- -- -- --- -- -- -- -- -- --- -- -- -- -- -- --- -- -- -- -- -- -- -- DAM. q PM --- q AM. q PM - --- q AM. q PM --- q AM. q PM - -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- - - 9-43 - AUTOMATIC ROUTE SELECTION-ROUTE PLAN TABLES (516) Start Hour I Hour (AM/PM Route Plan Table No. 25 T Route List Number MON. 27 29 FRI. ! SAT. ! SUN. - -- -- - OAM, CPM - - -- -- -- - - -- -- -- - - -- -- -- -- - - -- -- -- - - -- -- -- - - -- -- -- - - -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- A- -- -- -- -- -- -- -- -- -- -- -- -- -- -- - __ - q AM,mPM OPM OAM, __ - q AMOPM - - •AMe~PM q AM.C]PM -- - q AMC]PM -- - q AMaPM -- ~-JAM, jJPr4 q UPM q -- -- q AM, P M -q AM, -qP AM M -q AM.nPM -- __ - q AMOPM -- q AM, q PM -- q AM, q PM -- ON-4 nPM -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- - - /IJAM. [7PM -- -- -- -- - - 0AM, f--JPM -- -- -- -- - - 0AM aI-4 -- -- -- -- -- 0AM, q jPM 30 THU. - - 28 WED. A M Cq P M CPM q AM, -- OAM, CPM 26 TUE. - 9-44 AUTOMATIC ROUTE SELECTION-ROUTE LISTS TABLE (2/4) l- Route -ist No t PRIORITY 1 1 TG MOD WT r PRIORITY 2 ALV TG -MOQ - t T- Set Data PRIORITY 3 TG MOD -ALV - _I- #15 -- - - OYes, ONo - - - - - - UYes, ON0 #16 -- _ _ OYes, [r]No - - - - - - #17 -- _ _ ayes, C]No - - - - - - #18 -- _ _ ayes, ON0 - - - - - - #19 -- _ _ ayes, ONo - - - - - - #20 -- - - - - - - #I21 -- - - - - - - #I22 -- - - - - - - #23 -- - - - - - - #24 -- - - - - - - #25 -- - - - - - #26 -- - - - - - - I - #27 -- - - - - - - #I28 -- - - c- - - #29 -- - - cm - - #30 -- - - - - - - #31 -- - - - - - - #32 -- - - - - - - x33 -- - - - - - - #34 -- _ _ q Yes,ONo q ayes,N o _ _ c]Yes, q No _ _ ayes, aNo ONo q jYes, -- aYes, [3No -- OYes, q No -- OYes, q No -- OYes, q No q OYes, N o q OYes, N o q q Yes,N o C]No q Yes, _ _ q Yes, q No _ _ ayes, q No - - - - - - OYes, q No q Yes, q No q Yes, ONo tJYes, ONo I q Yes,ONo Dyes, q No q Yes, q No I q Yes, q ]No q Yes, q No TJYes, Crdo q Yes, q No OYes, q No ayes, ONo OYes, q No q Yes, q No OYes, q No q Yes,C]No q Yes, q No Dyes, ONo \ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - PRIORITY 4 1 ALV 1 TG r-JJes, /--JNo OYes, q No OYes, ONo OYes, nNo OYes, ONo OYes, q No OYes, q No OYes, q No q Yes, ONo q Yes, q No 1 q Yes, q No q Yes, q No OYes, q No c]Yes, q No q Yes, q No C]Yes, q No aYes, q No q Yes, q No OYes, q No MOD AUTOMATIC ROUTE SELECTION-ROUTE LISTS TABLE (S/4) Route T -ist No. t PRIORITY 1 1 TG MOD WT PRIORITY 2 ALV TG -r MOD Set Data PRIORITY 3 ALV TG #35 - - ONo OYes, -- -- -- Dyes, ONo #36 - - ONo UYes, -- -- -- #37 - - _ _ OYes, ~NO #38 - - #39 - - #40 - - #41 - - #42 - - #43 - - #44 - - #45 - - #46 - - #47 - - #48 - - #49 - - #50 - - #51 - - #52 - - #53 - - #54 - - ONo q Yes, ayes, ONo I _ ayes, ONo C]No q Yes, _ _ Dyes, C)No _ _ OYes, ONo _ _ Dyes, q ]No - _ ayes, q N0 -- Dyes, DNo -- ayes, q No [z1No -- DY es, ONo Dyes, ONo ayes, ONo q Yes, _ _ aYes, q No _ _ ayes, q No _ _ ayes, UNo -- -- --- -- --- -- --- -- --- -- --- -- --- -- --- -- --- -- --- -- --- -- -- -- -- --- -- --- -- --- -- --- -- --- -- --- -- -- q Yes, q No Dyes, q No Dyes, ONo q Yes,ONo q Yes,ONo Dyes, ONo Dyes, ONo q Yes, q No Dyes, q No q Yes,ONo q Yes, q No q Yes, q No Dyes, ONo aYes, q No ayes, ONo aYes, q No Dyes, UNo q Yes, q No q Yes, q No T MOD -- - - -- -- - - -- -- - - -- -- - - -- -- - - -- -- - - -- -- - - -- -- - - -- -- - - -- -- - - -- -- - - -- -- - - -- -- - - -- -- - - -- -- - - -- -- - - - -- -- - - -- -- - - -- -- - - -- -- - - -- PRIORITY 4 ALV TG Dyes, q No Dyes, q No q Yes, ONo Dyes, @No aYes, NO q Yes, q No ayes, ONo Dyes, q No aYes, q No q Yes, ONo Dyes, q No OYes, q No Dyes, ONo Dyes, q No q Yes, q No q Yes, ONo Dyes, UNo q ]Yes,flNo q Yes, q No aYes, q No MOD - - - - - - -- - - - - -- -. - - -- - - - - -- - - - - -- - - - - -- - - - - -- - - - - -- - - - - -- - - - - - - - - - -- - -.. -- - . -. - - - - .-._ .- .-_. -.. - _ .-- -.- . _ - - - - - ..- --_ -- AUTOMATIC ROUTE SELECTION-ROUTE LISTS TABLE (4/4) Set Data Route ,ist No, TG MOD W ALV TG MOD #55 -- _ _ oYes,oNo -- - - -- #56 -- _ _ OYes, ONo -- - - -- #57 -- _ _ nYes, ONo -- - - -- #58 -- -- - - -- #59 -- -- - - -- #60 -- -- - - -- #61 -- -- - - -- #62 -- -- - - -- #63 -- -- - - -- #64 -- -- - - -- _ _ _ _ _ _ _ _ OYes, _ OYes, _ OYes, _ OYes, _ OYes, _ OYes, _ ayes, q No q No ONo ONo ON0 q No q No ALV TG MOD T OYes, q No - - - - -ayes, ONo - - - - -ayes, [13No - - - - -OYes, q No - - - - -OYes, q ]No - - - - -Dyes, ONo - - - - -Dyes, ONo - - - - -OYes, n?h3 - - -- -aYes, ONo - - - - - q Yes, q No -- -- -- ALV TG-_ --_ ONo - -..- _- aYes, ONo - aYes, c]JNo -- . . Iayes, _. q Yes, NO . _ _ Dyes, ONo .- .- _ -.-. ~Yos, 1.. INo q Yes,ONo _-. __ OYes, ON0 OYes, aNo - - - q Yes, ONo -- -- --- --. i AUTOMATIC ROUTE SELECTION-MODIFIED DIGIT TABLE (l/2) Ent. No. Set Data Del. Digits to be inserted 01 02 03 04 -- 05 06 07 -._- 08 09 10 11 - 12 13 --_- 14 15 16 Note: Selection of Value I Del. Digits to be inserted l 1 digit (0 to 9) : digit to be deleted ~ maximum 26 digits consisting of numbers, l , #. and marks below H: Home position, ( : Secret (Start) P: Pause, ] : Secret (End) D: Switch to DTMF. -: *Secret has to be input as a pair ([ I). Setting up blanks means all blank. 9-50 Default Value 0 blank AUTOMATIC ROUTE SELECTION-MODIFIED DIGIT TABLE (2/2) 9-51 10. Special Attended SPECIAL ATTENDED-UCD (l/2) OT FDN OFDN FDN JCD UCD- , . . No. Set Data Set [ ,ata Default Set Data Defau’t No. Set Data D,eafr$ Value Value OFDN Set Data v?$uu$ Set Data lore; UCD: UCD group F D N : Floating DN (dial number of 3 or 4 digits, blank) OFDN: Overflow DN (dial number of 3 or 4 digits, blank) Overflow Time (1 to 10 minutes) OT: Pressing TAB hey scrolls the UCD No. For UCD No. (01 to 04) following DN can be set up as OFDN. Fytension DN. FDN of another UCD group era1 operator FDN l l l For UCD No. (05 to 32) same DN as for UCD No. (01 to 04) can be set as OFDN. However FDN of UCD No. (01 to 04) can not be set up. Connection of OFDN and OT between UCD No. (05 to 32). Blank has to be set for both OFDN and OT. Incomplete setting ot OFDN and OT causes error. l d OT SPECIAL ATTENDED-UCD (2/2) Set Data / UCD / No. / --- --S --- --, __- - --+ --- --- ----, --- --- blank --- ---* --- Remark: Selection of value for UCD Time Table 1T: 15 sec. timer 2T: 30 sec. timer 3T:45 s e c . t i m e r c .._. 4T: 60 sec. timer 01 W: ff OGM 1 is busy when it is sent out, wait until it becomes idle. 02W: ff OGM 2 is busy when it is sent out, wait until it becomes idle. 01 S: ff CGM 1 is busy when it is sent out, skip to the next command. 02s: ff CGM 2 is busy when it is sent out, skip to the next command. H: Send out the Hold tone. TR: Transfer to the overflow DN. OFF: disconnect 10-4 ---+ --- --- ---+ ----+ _-- ---+ ----, --- --- --- ----, ----+ - ----, __- ----, --- --- --- blank --, - --, 4 --- --- _-- --- --- - ---, - - --, --- --- __- --- --- --- - - + --- - --- --- --- blank - - --+ --- --- --- --- - --- - ---S ----, --- --- --- --- --+ --- ----t - ---S - - --- --- --- --, - --7 --+ --- --- --- --- --- 3 Default Value - --- --S - --- --- --- --- - --, --- --- __- 2 - UCD Time Table 9 1 - _-- --- blank 11. Miscellaneous MISCELLANEOUS- POWER FAILURE TRANSFER ASSIGNMENT -- T No. Extension Trunk Set Data Shelf Value blank 1 Set Data 3efaul. tl ___ .--Slot Vafi; e -- blank Shelf Iefaul, Value Set Data Slot Default Value blank __ - blank 2 -- - - 3 -- - - 4 -- - - 5 -- - - 6 -- - - 7 -- - - 8 -- -~ 9 -- - - 10 -- - - 11 -- - - 12 -- - - 13 -- - - 14 -- - - 15 -- - - 16 -- - - 17 -- - - 18 -- ~ , Note: Selection of Value Item Shelf 1 : 2 : 3 : blank : for for for not Basic shelf Expansion shelf t Expansion shelf 2 assigning Slot 01 to 12 : for Basic shelf 01 to 15 : for Expansion shelf (1 and 2) blank : not assigning 11-l
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 872 Page Mode : UseOutlines Page Layout : SinglePage Mod Date : 2002:01:12 00:02:29-06:00 Creation Date : 1999:10:21 16:08:32+01:00 Producer : Acrobat 4.0 Scan Plug-in for Windows Author : EZ Manuals Modify Date : 2002:01:12 00:02:29-06:00 Create Date : 1999:10:21 16:08:32+01:00 Metadata Date : 2002:01:12 00:02:29-06:00 Creator : EZ ManualsEXIF Metadata provided by EXIF.tools