RP 6 MANUAL Digi Tech RP6 Guitar Effects Owner’s RP6manual

User Manual: DigiTech RP6 Guitar Effects Owner’s Manual Troubleshoot DigiTech RP6 Guitar Effects |

Open the PDF directly: View PDF PDF.
Page Count: 30

A Harman International Company
S-DISC™
PROCESSING
RP-6
Guitar Signal
Processor/Foot
Controller and Preamp
Owner's Manual
DECLARATION OF CONFORMITY
Manufacturer’s Name:Harman Music Group Incorporated
Manufacturer’s Address: 8760 S. Sandy Parkway
Sandy, Utah 84070, USA
declares that the product:
Product Name: RP-6
Product Options: All (requies a Class II power adapter that conforms to the requirements of
EN60065, EN60747, or equivalent).
conform to the following Product Specifications:
Safety: EN 60065 (1993)
IEC 65 (1987) with Amendments 1, 2 & 3
EMC: EN 55013 (1990)
EN 55020 (1991)
Supplementary Information:
The product herewith complies with the requirements of the Low Voltage Directive
73/23/EEC and EMC Directive 89/336/EEC as amended by Directive 93/68/EEC.
.
Harman Music Group Incorporated
Vice President of Engineering
8760 S. Sandy Parkway
Sandy, Utah 84070, USA
Effective October 1, 1996
European Contact: Your Local DigiTech Sales and Service Office or
International Sales Office
3 Overlook Drive #4
Amherst, New Hampshire 03031, USA
Tel (603) 672-4244
Fax (603) 672-4246
Section 7 - Appendix
RP-6 Owner’s Manual
1
Table Of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Lithium Battery Warning . . . . . . . . . . . . . . . . . . . . . . . . 4
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SECTION 1 - STARTUP Supplying power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Line Conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pedalboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Parameter Matrix. . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Display Window . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Value, Store, and Edit Keys. . . . . . . . . . . . . . . . . . . 8
Parameter Selection Keys . . . . . . . . . . . . . . . . . . . . 8
Main Output Level. . . . . . . . . . . . . . . . . . . . . . . . . . 8
Presence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CC Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rear Panel Connections . . . . . . . . . . . . . . . . . . . . . . . . 8
Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Right Main Output. . . . . . . . . . . . . . . . . . . . . . . . . . 8
Left Main Output . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Headphone Output . . . . . . . . . . . . . . . . . . . . . . . . . 8
AC Line Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SECTION 2 - BASIC OPERATIONS About RP-6’s Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Program Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Bank Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Edit Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Store Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Bypass Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Tuner Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table of Contents
RP-6 Owner’s Manual
2
SECTION 3- EFFECTS AND PARAMETERS About the Parameter Matrix. . . . . . . . . . . . . . . . . . . . . . 13
Compression. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CC Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Silencer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Master Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Equalization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Speaker Cab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Wahs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Mod/Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Choruses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Flangers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Phasers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Tremolos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Auto Panners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Pitch Shifters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Whammy™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Dual Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Reverb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SECTION 4- APPENDIX Reinitializing the RP-6 . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Program List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table of Contents
RP-6 Owner’s Manual
3
INTRODUCTION Congratulations, and thank you for your purchase of the DigiTech RP-
6 Guitar Signal Processor / Preamp. The RP-6 offers you the same
fresh approach to guitar sound creation as the now famous RP-10.
DigiTech’s revolutionary S-DISC™ processor makes it all happen. Its
compact size occupies less floor space, while maintaining the power
of analog distortion, with the precision and clarity of the S-DISC™ digi-
tal multi-effects. Special features of the RP-6 include:
• Full bandwidth effects (20-20kHz)
• Stereo signal processing
• Quick Module and Parameter access
• CC pedal which allows for real time control of certain Parameters
• Programmable cabinet emulation for running direct to a mixing
console (great for both studio and live applications)
• Front panel Presence control and headphone output
All of your effects needs can be filled by a single unit. This owner’s
manual is your key to understanding the powerful world of the RP-6.
Read it carefully. After you’ve had time to familiarize yourself with the
unit, try experimenting with unusual effects settings. You may achieve
some interesting results.
SAFETY PRECAUTIONS Do not open the unit. Do not attempt to service the unit yourself.
Refer all servicing to qualified personnel. Opening the chassis for any
reason will void the manufacturer’s warranty. Do not get the unit wet.
If liquid is spilled on the unit, shut it off immediately and take it to a
dealer for service. Disconnect the equipment during storms to prevent
damage.
U.K. ONLY - A moulded mains plug that has been cut off from the
cord is unsafe. Discard the mains plug at a suitable disposal facility.
NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A
DAMAGED OR CUT MAINS PLUG INTO A 13 AMP POWER SOCKET.
Do not use the mains plug without the fuse cover in place.
Replacement fuse covers can be obtained from your local retailer.
Replacement fuses are 13 amps and MUST be ASTA approved to
BS1362.
LITHIUM BATTERY WARNING CAUTION! This product contains a lithium battery. There is danger of
explosion if battery is incorrectly replaced. Replace only with an
Eveready CR 2032 or equivalent. Make sure the battery is installed
with the correct polarity. Discard used batteries according to manu-
facturer’s instructions.
ADVARSEL! Lithiumbatteri - Eksplosjonsfare. Ved utskifting benyttes
kun batteri som anbefalt av apparatfabrikanten. Brukt batteri
returneres apparatleverandøren.
ADVARSEL! Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri av samme fabrikat og type. Levér
det brugte batteri tilbage til leverandøren.
Introduction and Safety
RP-6 Owner’s Manual
4VAROITUS! Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppin.
Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.
VARNING! Explosionsfara vid felaktigt batteribyte. Använd samma
batterityp eller en ekvivalent typ som rekommenderas av apparattil-
lverkaren. Kassera använt batteri enligt fabrikantens instruktion.
WARRANTY 1. The warranty registration card must be mailed within ten days after
purchase date to validate this warranty.
2. DigiTech warrants this product, when used solely within the U.S., to
be free from defects in materials and workmanship under normal
use and service.
3. DigiTech liability under this warranty is limited to repairing or
replacing defective materials that show evidence of defect, provid-
ed the product is returned to DigiTech WITH RETURN AUTHO-
RIZATION, where all parts and labor will be covered up to a period
of one year. A Return Authorization number may be obtained from
DigiTech by telephone. The company shall not be liable for any
consequential damage as a result of the product’s use in any cir-
cuit or assembly.
4. Proof-of-purchase is considered to be the burden of the consumer.
5. DigiTech reserves the right to make changes in design or make
additions to or improvements upon this product without incurring
any obligation to install the same on products previously manufac-
tured.
6. The foregoing is in lieu of all other warranties, expressed or implied,
and DigiTech neither assumes nor authorizes any person to
assume any obligation or liability in connection with the sale of this
product. In no event shall DigiTech or its dealers be liable for spe-
cial or consequential damages or from any delay in the perfor-
mance of this warranty due to causes beyond their control.
DigiTech™, S-DISC™, Whammy™ and Silencer™ are registered
trademarks of DOD Electronics Corporation.
The information contained in this manual is subject to change at any
time without notification. Some information contained in this manual
may also be inaccurate due to undocumented changes in the product
or operating system since this version of the manual was completed.
The information contained in this version of the owner’s manual super-
sedes all previous versions.
Warranty
RP-6 Owner’s Manual
5
SECTION 1 - STARTUP
SUPPLYING POWER Line Conditioning - The RP-6, like any piece of computer hardware,
is sensitive to voltage drops, spikes, and surges. Interference such as
lightning or power “brownouts” can seriously, and in extreme cases,
permanently damage the circuitry inside the unit. Here are some ways
to avoid this type of damage:
• Spike/Surge Suppressors - This is an inexpensive solution to all
but the most severe of AC line conditions. Surge protected
power strips usually cost only slightly more than unprotected
strips, making them a worthy investment for protection of all your
valuable gear.
• AC Line Conditioners - This is the best way to go for total pro-
tection from improper line voltages, albeit the more expensive
way. Line conditioners constantly monitor for excessively high or
low voltages and adjust accordingly, thus delivering consistent
power levels.
FRONT PANEL CONTROLS The front panel controls and functions of the RP-6 are as follows (refer
to diagram):
Section 1 - Startup
RP-6 Owner’s Manual
61) Pedalboard - The RP-6’s pedalboard consists of six footswitches.
The two Mode footswitches to the right of the Parameter Matrix
allow you to change from Program mode to Bank mode by press-
ing the UP & DOWN footswitches simultaneously. When changing
modes, the appropriate LED will light to indicate whether you are in
Program mode or Bank Mode. In Program Mode, the <UP> and
<DOWN> footswitches allow you to move through Programs, while
the four main switches, labeled 1 - 4, act as toggle On/Off switch-
es for Distortion, Modulation, Delay, and Reverb. In Bank mode,
the <UP> and <DOWN> footswitches allow you to move through
Banks, while the 1-4 footswitches are used to select Programs. If
footswitches 1 and 2 are pressed simultaneously, Tuner Mode will
be activated. If footswitches 3 and 4 are pressed simultaneously,
Bypass Mode will be activated.
2) Parameter Matrix - The Parameter Matrix consists of a group of
horizontal Effect LEDs and a second group of vertical Parameter
LEDs. The Effect LEDs are: Compressor, Distortion, Silencer,
Equalization, Speaker Cab, Wah Wah, Mod/Pitch, Dual Delay, and
Reverb. This matrix shows you exactly what Effects and Parameters
are in use.
3) Display Window - The display window shows all current operating
and programming information and is comprised of two parts: the
seven segment LED displays and the Signal, Clip, and Store indica-
tor LEDs. The first numeric LED in the display window indicates
whether you are in a User (U) or Factory Bank (F). The second
indicates the Bank number currently in use, and the third indicates
which Program number is currently in use. These numbers change
as you scroll through the available Programs. The functions of the
Signal, Clip, and Store indicator LEDs are as follows:
• Signal - Indicates whether a signal is entering the RP-6.
• Clip - Indicates analog clipping in the RP-6. Digital clipping can
be detected when the third vertical LED from the top of the
Parameter Matrix flashes. Distortion may be heard in the output
signal if either analog or digital clipping occurs. If analog clip-
ping occurs, check the Distortion On/Off levels. The levels may
need to be lowered to eliminate the problem. To reduce digital
clipping, the Master Volume and/or Effects levels should be
checked and adjusted accordingly. As always, let your ears be
the judge.
• Store - Lights when a Parameter has been changed in a
Program. When <STORE> is pressed once, the first seven seg-
ment LED in the Display window will flash. Once you have
selected the Bank and Program location where you want to store
your effects, press the <STORE> key again (see page 11, under
Edit Mode for further information on storing a Program).
Section 1 - Startup
RP-6 Owner’s Manual
7
4) Value, Store and Edit Keys - The Value <UP> and <DOWN> keys
allow you to scroll through the RP-6’s Programs, or change
Parameter values in Edit mode. The <STORE> key allows you to
store an edited Program in memory for later use. The <EDIT> key
allows you to edit the User and Factory Programs.
5) Parameter Select Keys -The <LEFT> and <RIGHT> Parameter
keys allow you to navigate the horizontal Effect LEDs of the
Parameter matrix. The <UP> and <DOWN> Parameter keys allow
you to navigate the vertical Parameter LEDs of the Parameter
matrix. These keys are only active in Edit mode.
6) Output Level - Controls the overall output level of the RP-6. Also
controls the overall level of the headphones.
7) Presence - Enhances the high frequency content of the overall
sound. This will affect all presets.
8) Continuous Control Pedal - This volume-type pedal allows real-
time control over Parameters in the RP-6.
REAR PANEL CONNECTIONS The RP-6 rear panel connectors and functions are as follows:
1) Input - This is the RP-6’s audio input. Plug your guitar in here.
2) Headphone Output - 1/4” stereo plug for headphones. The head-
phone level is controlled by the main output level knob.
3) Left/Mono Main Output - This is the RP-6’s left main audio output.
This output must be used if a mono effect is desired.
4) Right Main Output - This is the RP-6’s right main audio output.
Use both left and right main outputs to take advantage of stereo
effects.
5) AC Line Input - This is the AC adapter receptacle.
INPUT RIGHT
OUTPUT
LEFT/MONO
OUTPUT
HEADPHONES POWER
9VAC 1.33A
12345
Section 1 - Startup
RP-6 Owner’s Manual
8
Basic Guitar Setup
Section 1 - Startup
RP-6 Owner’s Manual
9
Recording Setup (Use Cabinet Emulator)
Section 1 - Startup
RP-6 Owner’s Manual
10
SECTION 2 - BASIC OPERATIONS
ABOUT THE RP-6 MODES The RP-6 offers five modes, allowing easy operation of the Effects and
Parameters. The modes are as follows:
PROGRAM MODE Allows you to scroll through the 40 Programs by using the <UP> and
<DOWN> Value keys as well as the <UP> and <DOWN> footswitch-
es. Enter Program mode by pressing the <UP> and <DOWN>
footswitches simultaneously until the Program LED lights and a P
appears briefly in the display window. Footswitches 1-4 act as on/off
toggle switches for the specified effects. Exit Program mode by
changing to another mode.
BANK MODE Allows you to scroll quickly through Banks without going through
every Program to get to the next Bank. Enter Bank mode by pressing
the <UP> and <DOWN> footswitches simultaneously until the Bank
LED lights and a Bappears briefly in the display window. When you
enter Bank mode, the Bank and Program numbers from the previous
mode will be retained. When a Program number is displayed in the
third LED of the display window, you can use the Value <UP> and
<DOWN> keys to scroll through Programs and Banks. This works
exactly like Program mode.
When the <UP> and <DOWN> footswitches are used in Bank mode,
you will scroll through Banks only. When you change a Bank using
this method, the previous Program number is not displayed with the
new Bank. The LEDs above footswitches 1-4 will begin flashing, indi-
cating that you can choose a Program in the selected Bank by press-
ing one of the four footswitches. Once a Program number has been
selected, both the Bank and Program numbers will be displayed. Exit
Bank mode by changing to another mode.
EDIT MODE Allows you to change Effects and Parameters in a Program. Enter Edit
mode by pressing the <EDIT> key. The Display window now shows
the value of the Parameter indicated by the LEDs in the Matrix. You
can scroll through the Parameter matrix using the Parameter Select
keys. The <UP> and <DOWN> keys allow you to scroll through the
vertical Parameter LEDs, while the <LEFT> and <RIGHT> keys allow
you to scroll through the horizontal Effect LEDs.
After selecting a Parameter, you can scroll through its values with the
<UP> and <DOWN> Data keys. When moving through Parameter val-
ues, the decimal point next to the Parameter value will flash when a
stored value has been changed. If you return to the original value, the
decimal point will stop flashing. If you exit Edit mode after changing
the Parameters and then return to Edit mode, the last viewed
Parameter will be displayed.
Section 2 - Basic Operations
RP-6 Owner’s Manual
11
STORE MODE Once you have modified the Parameters and Effects, you can store
them to a user Program location. When you change an Effect or
Parameter in a Program, the Store LED will light, indicating that you
have changed a Parameter and need to store the changes. Press the
<STORE> key once and the first seven segment LED in the Display
window will flash U. Select the Program and Bank you want to store
your changes to, and press the <STORE> key again to save the
changes. Exit this mode by pressing any footswitch or Value key.
BYPASS MODE Allows you to bypass the RP-6’s Effects. Enter this mode by pressing
footswitches 3 & 4 simultaneously. BYP will appear in the display
window to indicate you are in Bypass mode. Exit this mode by press-
ing any of the footswitches. When you exit this mode, the RP-6 will
default to the last mode you used. Bypass is not available while in
Edit mode.w
TUNER MODE Allows you to tune your guitar. Enter Tuner mode by pressing
footswitches 1 & 2 simultaneously. tun will appear briefly in the dis-
play window followed by --- to indicate that you are in Tuner mode. To
begin tuning play a note on your guitar (a harmonic at the 12th fret will
work best). The display window will show the note being played and
the horizontal Parameter Matrix LEDs just under the tuning bar will
light. Once the LED directly under the IN TUNE of the tuning bar is lit,
the note will be in tune. If the note is not in tune, 1 or 2 of the LEDs left
or right of the IN TUNE LED will be lit. If they are to the left, the note is
flat and should be tuned up. If the LEDs are to the right, the note is
sharp and should tuned down. You can change your tuning prefer-
ence by using the value <UP> and <DOWN> keys. The default facto-
ry setting is : A=440 Hz. The tuning reference control ranges from 427
Hz to 453 Hz, which is the equivalent of ± 50 cents (1/2 semitone) in
either direction form 440 Hz.
When you scroll down from 427 Hz, you will also find alternate
dropped tunings. Alternate tunings are A = Ab (415), A = G (392),
and A = Gb (370). The display window will briefly flash the currently
selected tuning preference.
Exit this mode by pressing any of the footswitches. When you exit this
mode, the RP-6 will default to the last mode you used. Tuner is dis-
abled in Edit mode.
Section 2 - Basic Operations
RP-6 Owner’s Manual
12
SECTION 3 - EFFECTS AND PARAMETERS
ABOUT THE PARAMETER MATRIX The Parameter Matrix displays all the Effects and Parameters you can
find in the RP-6. The Parameters are arranged in rows and columns.
Use the Parameter Select keys to navigate the matrix. The Effects and
their Parameters are as follows:
The RP-6’s Compression can be used to increase sustain and to tight-
en up guitars, and is particularly useful on clean sounds. Parameters
of the RP-6 compressor are as follows:
On / Off..........................Turns the Module on or off.
Amount ..........................Controls the amount of compression applied
to the signal. Higher settings yield a tighter,
more focused sound, while lower settings
allow better dynamics. Ranges from 1-Lo to
78-Hi.
The RP-6’s CC Pedal allows you to control various Parameters of spe-
cific Effects with a Continuous Control Pedal.
Type .............................There are eight Parameters that can be con-
trolled by the CC Pedal. These Parameters are
labeled with parenthesis in the Parameter
Matrix, indicating which CC value controls that
Parameter.
CC Pedal
Parameters Displayed Values
Type OFF ... CC1 ... CC8
Max Value Parameter dependent
Min Value Parameter dependent
Compression
Parameters Displayed Values
On/Off OFF-ON
Threshold LO-1...78-HI
Section 3 - Programming
RP-5 Owner’s Manual
13
Max Value .......................Sets the maximum value that the parameter
assigned to the CC Pedal will reach when
the Pedal is in the forward position. Range
varies according to the parameter selected.
Min Value ........................Sets the minimum value that the parameter
assigned to the CC Pedal will reach when
the Pedal is in the back position. Range
varies according to the parameter selected.
The distortion section of the RP-6 has two extremely flexible distortion
types, capable of producing the smoothest of the blues tones to the
full shred gain of a cranked up stack.
On / Off..........................Turns the Module on or off.
Type ..............................Selects the type of Distortion. Overdrive (odr)
is a low to medium gain distortion, and
Grunge (Gru) is an over the top high gain dis-
tortion.
Gain...............................Controls the amount of distortion produced by
the RP-6. High settings produce greater gain
and drive for effortless soloing, while low set-
tings offer better nuance and dynamic control.
Ranges from 0.6 to 11.0.
On Level........................Sets the output level of the Distortion while the
effect is ON. Ranges from -∞to 12.
Off Level........................Sets the output level of the Distortion while the
effect is OFF. Ranges from -∞to 12.
Distortion
Parameters Displayed Values
On/Off OFF-ON
Gain º6...1¡0
Type odr-Gru
On Level -oo...12
Off Level -oo...12
Section 3 - Effects and Parameters
RP-6 Owner’s Manual
14
The RP-6’s Silencer offers you a professional quality digital noise
reduction effect.
On / Off..........................Turns the Module on or off.
Threshold ......................Sets the level at which the Silencer™ gate will
open. Ranges are Lo and High.
Attenuation ....................Sets the amount of attenuation (noise floor
reduction) when the Silencer™ gate is closed.
Varies from 100 dB (eliminates the signal
completely) to 0 dB (no attenuation).
Attack Time ...................Controls how fast the Silencer™ gate opens
after detecting a signal above the threshold.
Large numbers yield slower attack times,
while small numbers give a fast attack. Varies
from 0 to 2000 milliseconds (2 seconds).
The RP-6’s Master Volume controls the overall volume level of the
selected program. The level can be controlled with the CC
expression pedal for balancing levels in real-time during live per-
formance. It is also useful to lower the overall digital effects level
if clipping occurs.
Level .............................Controls the overall volume level. This can be
done with the CC pedal or the Value keys.
Variable from 0 to 100.
Master Volume
Parameters Displayed Values
Level (CC1) 0...100
Silencer
Parameters Displayed Values
On/Off OFF-ON
Threshold LO-HI
Attenuation 0...100
Attack Time º00...™00
Section 3 - Effects and Parameters
RP-6 Owner’s Manual
15
The RP-6 offers a three band parametric equalizer with preset Q’s.
The center frequency of each band is adjustable along with its gain
(boost or cut).
High Q settings yield narrow bandwidth, where boost and cut have
minimal effect on adjacent frequencies of the program material. Low
Q settings affect a wider number of frequencies when the selected
band is boosted or cut.
With a Q setting of .5 you can see from the diagram that a large num-
ber of frequencies are affected by boosting the center frequency.
Now take a look at the middle and lower curves in the diagram, and
notice the much narrower bandwidth of the curves with a Q setting of
1 and 2.
20.000
DigiTech Audio Precision STD AMPL (dBr) vs FREQ (Hz)
Q = .5
15.000
10.000
5.0000
0.0
-5.000
-10.00
-15.00
-20.00
Q = 1
Q = 2
10kHz1kHz
Equalization
Parameters Displayed Values
Freq1 (Q= 0.5) kHz
Gain 1
Freq 2 (Q= 1.0) kHz
º02...1§0
-15...0...15
º02...1§0
Gain 2 -15...0...15
Freq 3 (Q= 2.0) kHz º13...1§0
Gain 3 -15...0...15
Section 3 - Effects and Parameters
RP-6 Owner’s Manual
16 Frequency .....................Allows you to select the center frequency of
each band (refer to the diagram above).
Ranges for frequencies 1 & 2 are .02 to 16.0
(20 Hz to 16 kHz). The Range for frequency 3
is 0.13 to 16.0 (130 Hz to 16 kHz).
Gain...............................Allows you to boost and cut the frequency.
Ranges are from -15 to 15.
The RP-6’s programmable Speaker Cabinet circuitry allows you to use
it in both recording and live situations without lugging heavy amps
and/or cabinets around. Just connect the RP-6 outputs to a mixing
console and kick in the Speaker Cabinet. No miking hassles, no heavy
equipment, just full on miked cabinet sound. Programs can be stored
with different Speaker Cabinet settings so you can customize your
Banks for whatever sound types you need. Parameters are as follows:
On / Off..........................Turns the Module on or off.
Cabinet Type.................Selects the tonal characteristics of the simulat-
ed cabinet. There are 10 different cabinet
types; 1-3 are warm cabinets, 4-6 are medium
cabinets, 7-9 are bright cabinets, and 10 is a
full bandwidth cabinet for maximum frequency
response.
Speaker Cab
Parameters Displayed Values
On/Off OFF-ON
Type 1...10
Section 3 -Effects and Parameters
RP-6 Owner’s Manual
17
The RP-6 offers a classic wah wah effect, which can be used with or
without Distortion for that classic Wah-Wah sound. The effect’s posi-
tion can be controlled with the CC Pedal.
On / Off..........................Turns the Module on and off.
Type ..............................The Wah Wah types include; Classic 1-3, Dark
& Deep 4, Mid Range 5, Full Range 6, and
Brass Attack 7.
Position..........................The PEDAL POSITION Parameter reflects the
current setting of the continuous control
device used to control the wah effect. This
Parameter can be modified manually using
the RP-6’s Parameter keys to perform the wah
function. As the Parameter is modified, the
tone of the original note will change. Ranges 0
to 127.
Is the RP-6’s multi-function module, allowing you to select effects such
as; Chorus, Flanger, Phaser, Tremolo, Panner, Pitch Shift, and
Whammy™ effect. The Parameters of these effects are adjusted in this
module.
Mod/Pitch
Parameters Displayed Values
On/Off
Type
Level (CC3)
OFF-ON
CHO
0...100
Value 1 (CC4) Speed
Depth
Delay
FLA
0...100
Speed
Depth
Regen
PHA
0...100
Speed
Depth
Regen
trE
0...100
Speed
Depth
PAn
0...100
Speed
Depth
Pch
0...100
Shift
Detune
bnd
0...100
Type
Position
Value 2 (CC5)
Value 3 (CC6)
Section 3 - Effects and Parameters
RP-6 Owner’s Manual
18 On / Off..........................Turns the Module on or off.
Type ..............................Allows you to select a specific type of modula-
tion/pitch effect. The Types are; Chorus,
Flanger, Phaser, Tremolo, Panning, Pitch
Shifting, and Whammy (Bnd).
Level..............................Controls the overall mix level of the mod or
pitch shifting effect. Ranges from 0 to 100.
Values 1, 2, & 3.............Once you have selected the specific Type of
effect you want, you can modify a specific
value within that Type. (The values are only
available when you are in the Type
Parameter.)
The RP-6 offers a chorus that is unique in both character and sound.
This dual chorus offers exceptionally rich chorusing using multiple
voices with different phasing characteristics. Chorus Parameters are
as follows:
Speed............................Controls the speed of the chorus sweep.
Ranges from 0 to 100.
Depth.............................This Parameter sets the sweep depth (intensi-
ty) of the chorus. Ranges from 0 to 100.
Delay .............................Sets the amount of delay present in the cho-
rus effect. Ranges from 0 to 100.
CHO (Chorus)
Values 1,2,&3 Displayed Values
Speed 0...100
Depth 0...100
Delay 0...100
Section 3 - Effects and Parameters
RP-6 Owner’s Manual
19
The RP-6 also offers exceptionally rich studio-quiet flanging. Flange
Parameters are as follows:
Speed............................Controls the speed of the flange sweep.
Ranges from 0 to 100.
Depth(+Delay)...............Sets the depth amount and delay present in
the flange effect. Ranges from 1 to 16.
Regeneration.................This Parameter sets the amount of regenera-
tion which is perceived as the sweep depth
(intensity) of the flange. Variable from -99 to
99.
The RP-6’s classic adjustable phase shifting effect is reminiscent of
mid-70’s keyboard and guitar sounds.
Speed............................Controls the speed of the phase sweep.
Ranges from 0 to 100
Depth.............................Sets the sweep depth (intensity) of the phas-
er. Ranges from 0 to 100.
Regeneration.................Controls the amount of phased sound fed
back to the input of the Module. High regen-
eration settings produce dramatic and inter-
esting unnatural sounds. Ranges from 0 to
99.
PHA (Phaser)
Values 1,2,&3 Displayed Values
Speed 0...100
Depth 0...100
Regeneration 0...99
FLA (Flanger)
Values 1,2,&3 Displayed Values
Speed 0...100
Depth (+Delay) 1...16
Regeneration -99...0...99
Section 3 - Effects and Parameters
RP-6 Owner’s Manual
20
Tremolo was one of the first real effects, and appeared mostly on
early guitar amplifiers. Because of this, tremolo is sometimes per-
ceived as sounding “old” or “vintage”. The RP-6, breathes new life
into this classic effect, providing totally transparent volume modulation
of sound sources.
Speed............................Controls the tremolo speed (speed of modula-
tion). Ranges from 0 to 100.
Depth.............................Adjusts the intensity of the tremolo effect.
Ranges from 0 to 100.
An auto panner is a modern relative of the tremolo that modulates the
sound from left to right at a given rate. Parameters are as follows:
Speed............................Controls the panning speed (speed of modu-
lation). Ranges from 0 to 100
Depth.............................Adjusts the intensity of the panning effect.
Ranges from 0 to 100.
PAN (Auto Panning)
Values 1,2,&3 Displayed Values
Speed 0...100
Depth 0...100
Not Available
trE (Tremolo)
Values 1,2,&3 Displayed Values
Speed 0...100
Depth 0...100
Not Available
Section 3 - Programming
RP-6 Owner’s Manual
21
This RP-6’s Pitch Shifting effect gives you a shifted signal from 0 to 24
semi-tones above or below the pitch of the input signal.
Shift............................Sets the interval between the original note and
the pitch shifted note. Variable from -24 to 24
Detune.......................Determines the amount of detuning applied to
the shifted note. Variable from -99 to 99.
The RP-6’s pitch bending effect allows you to smoothly shift between
two preset pitch intervals using the CC Pedal.
Type...........................Selects the function of the Whammy™ Module.
There are 16 functions available in regular
Whammy Modules. They are as follows:
1= Shallow Detune 9=Major 2nd Up to Major 3rd Up
2=Deep Detune 10=Minor 3rd Up to Major 3rd Up
3=1 Octave Up 11=Major 3rd Up to 4th Up
4=Up 2 Octaves 12=4th Up to 5th Up
5=Down 2nd 13=5th Up to 6th Up
6=Down 1 Octave 14=5th Up to Major 7th Up
7=Down 2 Octaves 15=4th Down to Minor 3rd Down
8=Down 6 Octaves 16=5th Down to 4th Down
Position.........................The POSITION Parameter reflects the current
setting of the Whammy™ effect. This
Parameter should be linked to the RP-6’s CC
pedal. As Position is modified, the pitch of the
original note will change in intervals according
to the setting of the WHAMMY TYPE. Ranges
from 0 to 100.
bnd (Pitch Bending/Whammy)
Values 1,2,&3 Displayed Values
Type 1 ... 16
Position 0 ... 100
Not Available
PCH (Pitch Shifting)
Values 1,2,&3 Displayed Values
Speed -24...0...24
Depth -99...0...99
Not Available
Section 3 - Programming
RP-6 Owner’s Manual
22
Delay times 1 & 2 can be programmed independently. However,
On/Off, Type, Level, and Feedback will program the same for BOTH
Delays 1 & 2. For example, if you choose to program your Level to 50,
both Delays 1 & 2 will be 50. Delay Parameters are as follows:
On / Off..........................Turns the Effect on and off.
Type ..............................Determines the type of delay. Type 1 is a
mono delay, Types 2 through 4 are two tap
mono delays, and Types 5 through 7 are two
tap stereo delays (see chart below for further
information).
Level..............................Controls the level of the delay in both Delay1
and Delay 2. Ranges from 0 to 100.
Delays 1 & 2..................The available delay time ranges are 0 (no
delay) to 800 milliseconds.
Feedback ......................The amount of time it takes for the Reverb to
fade to inaudibility. Ranges from 0 to 99.
Type:
1
2
3
4
5
6
7
Left Output:
Delay 1
Delays 1 & 2
Delays 1 & 2
Delays 1 & 2
Delay 1
Delay 1
Delay 1
Right Output:
Delay 1
Delays 1 & 2
Delays 1 & 2
Delays 1 & 2
Delay 2
Delay 2
Delay 2
Feedback Source:
Delay 1
Delay 1
Delay 2
Delays 1 & 2
Delay 1
Delay 2
Delays 1 & 2
Dual Delay
Parameters Displayed Values
On/Off
Type
Level (Mix)
OFF-ON
1...7
0...100
Delay 1 0...800
Delay 2 0...800
Feedback 0...99
Section 3 - Programming
RP-6 Owner’s Manual
23
Ambience, or reverberation, is produced when sound energy is
reflected off room surfaces and objects. Using reverberation in
recorded program material gives the listener a sense that the material
is being performed in an actual room or hall. It is this similarity to actu-
al acoustic spaces that makes reverberation a useful tool in recorded
music. Reverb Parameters and their functions are as follows:
On / Off..........................Turns the Module on or off.
Type ..............................Allows you to choose your ambience or set-
ting you want to use. There are ten available
type settings:
SPr=Spring StU=Studio
pLa=Plate Gar=Garage
sOU=Sound Stage HAL=Hall
bAt=Bathroom CHU=Church
CLU=Club ArE=Arena
Level..............................Controls the amount of reverb signal to be
mixed in with the dry signal. Ranges from 0 to
100.
EQ Frequency ...............Adjusts the center frequency of the Reverb
EQ. Varies from .02 to 16 kHz.
EQ Gain.........................Allows you to increase and decrease the level
of the EQ frequency. Varies from -15 to 15 dB.
Decay Time ...................The amount of time it takes for the Reverb to
fade to inaudibility. Ranges from 1 to 10.
Reverb
Parameters Displayed Values
On/Off
Type
Level
OFF-ON
CLU...SPr
0...100
EQ Freq (kHz) º02-1§0
EQ Gain -15...0...15
Decay Time 1...10
Section 3 - Programming
RP-6 Owner’s Manual
24
SECTION 4 - APPENDIX
REINITIALIZING THE RP-6 This option allows you to restore the contents of the RP-6’s memory to
the original factory condition.
WARNING: Performing this function will destroy all user-pro-
grammed data. All such data will be lost forever!
To restore the factory Programs, the procedure is as follows:
• Plug in the RP-6 while holding down the Parameter Select <UP>
key.
• When rSt appears in the display window, press the Value
<UP> key.
Section 4 - Appendix
RP-6 Owner’s Manual
25
SPECIFICATIONS A/D Converter: 16 bit PCM
D/A Converter: 16 bit PCM
Sampling Frequency: 40 kHz
DSP Section:
Architecture: Static-Dynamic Instruction Set Computer (S-DISC™)
Digital Signal Path Width: 24 bits (144.5 dB)
Internal Data Path Width: 48 bits (289 dB)
Dynamic Delay Memory: 64k x 24 bits (1.68 seconds)
Static Delay Memory: 256 24-bit registers (6.55 milliseconds)
Data ALU Processing: 10.0 MIPS
Address ALU Processing: 15.0 MIPS
Multiplier Size: 24 bits x 24 bits
Input Section:
Connector: 1/4” Unbalanced TRS
Nominal Level: -8 dBu
Maximum Level: +10 dBu
Impedance: 470 kohms
Output Section:
Connector: 1/4” TRS
Nominal Level: +4 dBu
Maximum Level: +18 dBu
Impedance: 50 ohms
General:
Frequency Response: 20 Hz. - 20 kHz. +0, -3 dB
S/N ratio: Greater than 90 dB; ref = max signal, 22 kHz measurement
bandwidth
Total Harmonic Distortion: Less than 0.04% (1 kHz.)
Memory Capacity:
Factory: 40 Programs
User: 40 Programs
Power Requirements:
US and Canada: 120 V AC, 60 Hz
Japan: 100 V AC, 50/60 Hz
Europe: 230 V AC, 50 Hz
UK: 240 V AC, 50 Hz
Power Consumption: 12 watts
Dimensions: Legnth 18” Width 8.75” Height 2.75”
Section 4 - Appendix
RP-6 Owner’s Manual
26
BLOCK DIAGRAM Following is a simplified block diagram of the RP-6.
S-DISC™
Processor
(DSP)
Compressor Distortion
Input
A / D
Converter
D/A
Converter
1/4" Output Right
1/4" Output Left
Headphone Output
Output
Level
Signal/Clip LEDs
Presence
Section 4 - Appendix
RP-6 Owner’s Manual
27
PRESET LIST
Following is a list of all the factory Programs in the
RP-6.
Rock # Title
01 Big Easy
02 Chorus Church
03 Tap Delay/Chorus
04 Rock Wah/Delay
Pop
11 Flange Rhythm
12 12 String
13 Roto Phase Delay
14 Octave Down Wah
Heavy
21 Bone Crusher
22 Metal Rhythm
23 Clean Delay/Reverb
24 Meat Man
Alternative
31 Clean Wah
32 Fat Dirt Chorus
33 Clean Flange/Verb
34 Trem-O-Rhythm
Post Seattle
41 Fuzz Box
42 Grungy
43 Oct Up Whammy
44 Slow Phase Lead
Country # Title
51 Clean Slapback
52 Dirty Rhythm
53 Spaghetti Western
54 Pedal Steel (CC Pedal)
Retro
61 Pedal Phase
62 Surf King
63 Dirt Box
64 Transistor Distortion
Jazz/Fusion
71 Fusion Solo
72 Clean Jazz
73 Grit With Delay
74 Compressed Chorus
Blues
81 Bluesy Delay
82 Texas Blues
83 Blues Slide (CC Treadle)
84 Sparkley Clean
Special
91 Distortion Swell
92 Tape Machine
93 5th Above
94 Wah Wah Man
Section 4 - Appendix
RP-6 Owner’s Manual
8760 South Sandy Parkway
Sandy, Utah, 84070
Telephone (801) 566-8800
FAX (801) 566-7005
International Distribution: 7 Farmington Road
Amherst, New Hampshire 03031 U.S.A.
FAX (603) 672-4246
DigiTech™, S-DISC™, Whammy™ and Silencer™ are registered trademarks of
DOD Electronics Corporation
Copyright © 1996
DOD Electronics Corporation
Printed In U.SA 2/96
Manufactured in the U.S.A.
RP-6 18-2151-A
Revised 3/30/96
OS v1.00
E
This manual
is made from
recycled
materials.

Navigation menu