SP47W3
User Manual: SP47W3
Open the PDF directly: View PDF .
Page Count: 118
Download | |
Open PDF In Browser | View PDF |
PROJECTION TV RECEIVER Chassis : Model: PROJECTION TV RECEIVER J52A(P)_REV.4 SP47W3HFX/BOB SP47W3HFX/COM SP47W3HFX/EUE SP47W3HFX/XEH SP55W3HFX/XEC CONTENTS 1. Precautions 2. Reference Information 3. Specifications 4. Alignment and Adjustments 5. Troubleshooting 6. Exploded View and Parts List 7. Electric Parts List 8. Block Diagrams 9. Wiring Diagram 10. Schematic Diagrams ELECTRONICS © Samsung Electronics Co., Ltd. Nov. 2002 Printed in Korea 3J52A-SESA-47W3 Precautions 1. Precautions Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays. 1-1 Safety Precautions 1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which people—particularly children—might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit’s AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test. Samsung Electronics LEAKAGE CURRENT TESTER DEVICE UNDER TEST (READING SHOULD NOT BE ABOVE 0.5mA) TEST ALL EXPOSED METAL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED) EARTH GROUND Fig. 1-1 AC Leakage Test 6. Antenna Cold Check: With the unit’s AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection. 8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced. (X-ray protection circuits also may be called “horizontal disable” or “hold-down”.) Heed the high voltage limits. These include the X–ray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic. 1-1 Precautions 1-1 Safety Precautions (Continued) 9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. 10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer’s warranty. 11. Hot Chassis Warning: Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source. To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground. 12. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source. 13. Some TV chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered. 15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. 16. Picture Tube Implosion Warning: The picture tube in this receiver employs “integral implosion” protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original. 17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some “in-line” picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such “permanently attached” yokes from the picture tube. 18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original—even if the replacement is rated for higher voltage, wattage, etc. Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards. 14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. 1-2 Samsung Electronics Precautions 1-2 Servicing Precautions Warning 1 : First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning 2 : An electrolytic capacitor installed with the wrong polarity might explode. 1. Servicing precautions are printed on the cabinet. Follow them. 2. Always unplug the unit’s AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor. 3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. 4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). 6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 8. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last. 9. When some parts inside the optical engine (except lamp) are damaged, replace the whole optical engine. “CAUTION : Double-pole/neutral fusing” Samsung Electronics 1-3 Precautions 1-3 Precautions for Electrostatically Sensitive Devices (ESDs) 1. Some semiconductor (“solid state”) devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity. 2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power— this is an electric shock precaution.) 3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge. 4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs. 1-4 5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs. 6. Use only an anti-static solder removal device. Many solder removal devices are not rated as “anti-static”; these can accumulate sufficient electrical charge to damage ESDs. 7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. 8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. 9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD. Samsung Electronics Reference Information 2. Reference Information 2-1 Tables of Abbreviations and Acronyms Table 2-1 Abbreviations A Ah Å dB dBm °C °F °K F G GHz g H Hz h ips kWh kg kHz kΩ km km/h kV kVA kW I MHz Samsung Electronics Ampere Ampere-hour Angstrom Decibel Decibel Referenced to One Milliwatt Degree Celsius Degree Fahrenheit degree Kelvin Farad Gauss Gigahertz Gram Henry Hertz Hour Inches Per Second Kilowatt-hour Kilogram Kilohertz Kilohm Kilometer Kilometer Per Hour Kilovolt Kilovolt-ampere Kilowatt Liter Megahertz MV MW MΩ m µA µF µH µm µs µW mA mg mH mI mm ms mV nF Ω pF Ib rpm rps s V VA W Wh Megavolt Megawatt Megohm Meter Microampere Microfarad Microhenry Micrometer Microsecond Microwatt Milliampere Milligram Millihenry Milliliter Millimeter Millisecond Millivolt Nanofarad Ohm Picofarad Pound Revolutions Per Minute Revolutions Per Second Second (Time) Volt Volt-ampere Watt Watt-hour 2-1 Reference Information Table 2-2 Table of Acronyms ABL AC ACC AF AFC AFT AGC AM ANSI APC APC A/V AVC BAL BPF B-Y CATV CB CCD CCTV Ch CRT CW DC DVM EIA ESD ESD FBP FBT FF FM FS GND G-Y H HF HI-FI IC IC IF 2-2 Automatic Brightness Limiter Alternating Current Automatic Chroma Control Audio Frequency Automatic Frequency Control Automatic Fine Tuning Automatic Gain Control Amplitude Modulation American National Standards Institute Automatic Phase Control Automatic Picture Control Audio-Video Automatic Volume Control Balance Bandpass Filter Blue-Y Community Antenna Television (Cable TV) Citizens Band Charge Coupled Device Closed Circuit Television Channel Cathode Ray Tube Continuous Wave Direct Current Digital Volt Meter Electronics Industries Association Electrostatic Discharge Electrostatically Sensitive Device Feedback Pulse Flyback Transformer Flip-Flop Frequency Modulation Fail Safe Ground Green-Y High High-Frequency High Fidelity Inductance-Capacitance Integrated Circuit Intermediate Frequency I/O L L LED LF MOSFET MTS NAB NEC NTSC OSD PCB PLL PWM QIF R RC RF R-Y SAP SAW SIF SMPS S/N SW TP TTL TV UHF UL UV VCD VCO VCXO VHF VIF VR VTR VTVM TR Input/output Left Low Light Emitting Diode Low Frequency Metal-Oxide-Semiconductor-Field-Effect-Tr Multi-channel Television Sound National Association of Broadcasters National Electric Code National Television Systems Committee On Screen Display Printed Circuit Board Phase-Locked Loop Pulse Width Modulation Quadrature Intermediate Frequency Right Resistor & Capacitor Radio Frequency Red-Y Second Audio Program Surface Acoustic Wave(Filter) Sound Intermediate Frequency Switching Mode Power Supply Signal/Noise Switch Test Point Transistor Transistor Logic Television Ultra High Frequency Underwriters Laboratories Ultraviolet Variable-Capacitance Diode Voltage Controlled Oscillator Voltage Controlled Crystal Oscillator Very High Frequency Video Intermediate Frequency Variable Resistor Video Tape Recorder Vacuum Tube Voltmeter Transistor Samsung Electronics Reference Information 2-2 IC Line Up 2-2-1 100Hz Table 2 - 3 IC Line - Up No. 1 2 3 Block Name MAIN SUB TERMINAL CS MODEL 4 MICOM CW MODEL MICOM + TTX 5 Double Window(D/W) Samsung Electronics IC Location IC Name IC101 SAA1300 IC655 TDA7265 ICS801 TNY253P IC301 LA7845 IC471 TL494CN ICZ103,104 STK392-040 IC431 MC4558C IC703 PCF8574P ICP706 PCF8574P(Option) IC701,702 TDA6920X IC705 TC4052BP ICP705 TEA6422 ICP707 TEA5114A ICP704 TDA8601 IC706 PCF8591P IC901 Z9037116PS1 IC902 24C16 IC901 SDA30C264 IC902 27C040 IC903 8574 IC904 24C16 ICT01 SDA5275 ICT02 KM44C4004C IC06 SDA9361 IC07 CXA2101AQ IC01 VPC3230D-B2 IC02 SDP9400 IC03 SDS9280 2-3 Reference Information Table 2 - 3 IC Line - Up (Continued) No. 5 6 7 8 9 10 Block Name Double Window(D/W) Convergence Sound CRT POWER Sub AMP IC Location IC Name PIC01 VPC3230D-B2 PIC02 MS81V04160 IC111,112 CD40668BCM IC109,110 74HC4066 IC102 74HC4046 IC106,107,108 TL072 IC105 EL2210CS IC103 TSC87251G2D IC101 SDC91 IC104 AT82C64 ICD601 MSP3452G-A1 *ICD601 MSP3450G-B6 ICD602,603 TL062 IC501,531,561 TDA6111Q IC801S STRF6656 IC802 SVD001(OPTION) IC804 SE11ON ICS601 TDA 7265 (DOLBLY, SULLOON,OPTION) 11 Format Converter IC01 FS401S IC02 416S11/20 IC03 Z9021106PSC IC04 24C02 (PC,INPUT,OPTION) 2-4 Samsung Electronics Reference Information 2-3 MICOM IIC BUS LINE -UP Samsung Electronics 2-5 Reference Information MENO 2-6 Samsung Electronics Specifications 3. Specifications Broadcasting System PAL MULTI Scanning System 100HZ VHF : CH2 ~ CH13 Tuning Range UHF : CH14 ~ CH69 Cable : CH1, CH14 ~ 125 Antenna Impedance 75 ohm Unbalanced Video : 38.9 MHz Intermediate Frequency Sound : 33.4 MHz STD : 10W Sound Output Rated Voltage FULL MAX : 15W AC220V/AC110~250V/AC180~240V/50Hz CW White Balance High Voltage 47” Hx : 290 Lx : 290 Hy : 285 Ly : 285 Y : 8.0 Y : 0.3 55” Hx : 290 Lx : 290 Hy : 285 Hy : 285 Y : 7.5 Y : 0.25 43” Hx : 275 Lx : 258 Hy : 275 Ly : 255 Y : 9.5 Y : 0.4 47” Hx : 278 Lx : 268 Hy : 275 Hy : 262 Y : 8.25 Y : 0.29 55” Hx : 276 Lx : 267 Hy : 271 Hy : 258 Y : 7.9 Y : 0.29 CS 29KV 250V/6.3A FUSE CODE NO : 3601-000300 Power Consumption Samsung Electronics 280W 3-1 Specifications 3-1 TV Setup Mode MAIN MENU PC Enter ZOOM COMPRESS PC Enter FREEZE SE T UP RESET EXIT Switch to PC Mode Select Key Switch to External Mode TV/External Key Select menu F.Menu Key TV SETUP MENU T V SE TUP MENU SETUP MENU H POS LEFT T V SE T UP H SCALE SHRINK COMPUTER SETUP V POS PICTURE SETUP V SCALE SHRINK EXIT RECALL RIGHT H P OS L EF T RI GHT GROW DOWN UP GROW SETTINGS EXIT Adjust screen left to balance SAVE AND EXIT Adjust horizontal position (left) Volume- key Select TV Setup CH Down key Select TV Setup Volume+ key TV SETUP MENU TV SETUP MENU H SCA L E SHR INK GROW H POS LEFT H SCALE SHRINK V P OS DO WN V SCALE SHRINK RECALL Adjust screen left to balance RIGHT TV SETUP MENU GROW UP V P OS DOWN UP GROW SETTINGS Adjust screen top to balance EXIT SAVE AND EXIT Adjust horizontal position (right) Volume - key Select vertical position adjustment CH Down key TV SETUP MENU V SCAL E SHRI N K GROW SETUP MENU T V SE TUP M EN U H POS LEFT H SCALE SHRINK Adjust screen left to balance Adjust vertical position (top) Volume + key V POS DOWN V SCALE SHRINK RECALL RIGHT GROW T V SE T UP UP COMPUTER SETUP GROW PICTURE SETUP SETTINGS EXIT EXIT SAVE AND E XI T Adjust horizontal position (bottom) Volume+ key 3-2 . Save and Exit CH Down,Volume+ key Exit Samsung Electronics Alignment and Adjustments 3-2 Picture Setup Mode SETUP MENU P I CTURE SE TUP MENU PICTURE SETUP MENU BRIGHTNESS TV SETUP COLOR SATURETION COMPUTER SETUP FLICKER P I CTU RE SE T UP VIDEO FILTER EXIT RECALL BRI GHT NE SS FILTER SETTINGS EXIT SAVE AND EXIT Select Picture Setup CH Down key Set in the bright screen Select Picture Setup Volume+ key PICTURE SETUP MENU PICTURE SETUP MENU COL OR SAT URAT I ON F L I CKE R F I L T E R Adjust brightness Volume+ key P I CTURE SETUP MENU BRIGHTNESS COLOR SATURETION FLICKER FILTER VIDEO FILTER RECALL SETTINGS EXIT Set in the bright screen Set in the bright screen Adjust color saturation CH Down, Volume+ key Adjust flicker filter CH Down, Volume+ key SAVE AND E XI T Save and Exit CH Down, Volume- key MAIN MENU SETUP MENU ZOOM TV SETUP COMPRESS COMPUTER SETUP FREEZE P I CT URE SE T UP SE T UP EXIT RESET PC EXIT Finish picture setup Volume+ key 1. Finish Computer Setup F.Menu key Exit Adjust four different modes:VGA3 (VGA), VGA (DOS), VESA (SVGA), VEAS (XGA). 2). Perform the setup for each PC mode and picture setup. Samsung Electronics 3-3 Alignment and Adjustments 3-3 Picture Setup Mode (computer setup mode only) COMPUTER SETUP MENU SETUP MENU H P OS L EF T RI GHT TV SETUP H SCALE SHRINK GROW COMP UT E R SE T UP V POS PICTURE SETUP V SCALE SHRINK EXIT RECALL DOWN COMPUTER SETUP MENU H P OS L EF T RI GHT UP GROW SETTINGS EXIT Adjust screen left to balance SAVE AND EXIT Select Computer Setup CH Down key Select Computer Setup Volume+ key COMPUTER SETUP MENU COMPUTER SETUP MENU H SCAL E SHRI NK GROW H POS LEFT H SCALE SHRINK V P OS RIGHT COMPUTER SETUP MENU GROW DOWN UP V SCALE SHRINK GROW RECALL Adjust screen left to balance Adjust horizontal position (left) Volume- key V P OS DOWN UP SETTINGS Adjust screen top to balance EXIT SAVE AND EXIT Adjust horizontal position (right) Volume+ key COMPUTER SETUP MENU V SCAL E SHRI N K GROW Select vertical position adjustment CH Down key SETUP MENU COMPUTER SETUP MENU H POS LEFT H SCALE SHRINK Adjust screen left to balance Adjust vertical position (top) Volume+ key V POS DOWN V SCALE SHRINK RECALL RIGHT GROW UP GROW SETTINGS TV SETUP COMPUT E R SE T UP PICTURE SETUP EXIT EXIT SAVE AND E XI T Adjust horizontal position (bottom) Volume+ key Save and Exit CH Down, Volume+ key Exit 1. Adjust four different modes:VGA3 (VGA), VGA (DOS), VESA (SVGA), VEAS (XGA). 2. Perform the setup for each PC mode and picture setup. 3-4 Samsung Electronics Alignment and Adjustments 4. Alignment and Adjustments 4-1 General Alignment Instructions 4-3 FACTORY MODE CONTROL 1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus. 1. Enter & Concel the Factory Mode (1) Usual Remote Control Enter : PICTURE OFF -> DISPLAY KEY -> MENU KEY -> MUTE KEY -> POWER ON (Press each remote control key with in 3 seconds). Cancel : POWER OFF -> ON 2. Observe the picture for good black and white details. There should be objectionable color shading; if color shading is present, demagnetize, perform purity and convergence adjustments described below. 3. Use the specified test equipment or its equivalent. 4. Correct impedance matching is essential. 5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results. 6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate. 7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts. (2) Factory Remote Mode Enter : DISPLAY KEY -> FACTORY KEY (Press each remote control key with in 3 seconds). Cancel : POWER OFF -> ON Press the FACTORY key twice at intervals of at lease 1 second. (Enter the AGING Mode once) (3) Set Value When Entering the Factory Mode - Picture Mode & Sound Mode are set to the standard data. (4) Adjustments - CH.UP/DOWN Key : Use to select the item you want. - VOLUME UP/DOWN Key : Increases or decreases the value of data. - MENU Key : Use to save the current set value in EEPROM and exit to the upper mode. - Use the TV/VIDEO Key the conver to the AV Mode. 8. To protect against shock hazard, use an isolation transformer. 4-2 High voltage Check CAUTION : There is no high voltage adjustment on this chassis. The B+ power supply should be +135 volts (with full color- bar input and normal picture level). 1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 32 KV under any conditions. Samsung Electronics 4-1 Alignment and Adjustments 4-4 FACTORY MODE MENU 4-4-1 CW MODEL Service Mode Video Adjustment Y.C-Delay Deflection normal Deflection VGA Option byte Reset VIDEO ADJUSTMENT FUNCTION 4-2 INITIAL DATA RANGE R Drive 31 0 ~ 63 B Drive 31 0 ~ 63 G Drive 31 0 ~ 63 Gamma 12 0 ~15 R Cutoff 31 0 ~ 63 B Cutoff 31 0 ~ 63 G Cutoff 31 0 ~ 63 Sub Cont 7 0 ~15 Sub Brt. 31 0 ~ 63 Sub Color 7 0 ~15 Sub Tint 7 0 ~15 V Peaking 7 0 ~12 TTX Cont 10 0 ~15 TTX Bright 10 0 ~ 63 PIP Cont 0 0 ~15 PIP Bright 0 0 ~15 CG R Contrast 40 0 ~ 63 CG G Contrast 40 0 ~ 63 CG B Contrast 40 0 ~ 63 REMARK Samsung Electronics Alignment and Adjustments Y.C-DELAY FUNCTION INITIAL DATA RANGE PAL-B/G 6 0 ~15 PAL-D/K/L 8 0 ~15 PAL-I 8 0 ~15 SECAM-B/G 4 0 ~15 SECAM-D/K/L 6 0 ~15 NTSC 7 0 ~15 PAL-AV 5 0 ~15 SECAM-AV 4 0 ~15 NTSC-AV 6 0 ~15 DVD 9 0 ~15 INITIAL DATA RANGE P.V-SIZE -40 -128 ~ +127 P.V-SFT -39 -128 ~ +127 P.V-LIN 0 -128 ~ +127 P.S-CORR 0 -128 ~ +127 P.EW-WTH +28 -128 ~ +127 P.EW-PBL -27 -128 ~ +127 P.H-SFT -22 -64 ~ +63 P.EW-TPZ 0 -128 ~ +127 P.BOW 0 -128 ~ +127 P.ANGLE 0 -128 ~ +127 P.EW-UPCR 0 -128 ~ +127 P.EW-LOCR 0 -128 ~ +127 P.HOR-EHT 0 0 ~ +255 P.VER-EHT 0 0 ~ +255 P.INT. VOL. REF 0 -16 ~ +15 P.HSYNC DELAY +10 -128 ~ +127 REMARK DEFLECTION NORMAL FUNCTION Samsung Electronics REMARK 4-3 Alignment and Adjustments DEFLECTION NORMAL FUNCTION INITIAL DATA RANGE P.PHP 32 0 ~ 255 P.PVP 32 0 ~ 255 P.PHS 0 0 ~15 P.PVS 0 0 ~15 +30 -128 ~ +127 FUNCTION INITIAL DATA RANGE LIMIT LEVEL 0 0~3 SYSEM 1 0~3 CLP-MSK 0 0~3 ABL-MODE 1 0~3 ABL-TH 1 0~3 DTV-SYNC 69 0 ~ 255 CR-OFFSET1 10 0 ~ 15 CB-OFFSET1 10 0 ~ 15 CR-OFFSET2 7 0 ~ 15 CB-OFFSET2 7 0 ~ 15 CTI-LEVEL 1 0~3 R-Y/R 3 0 ~ 15 R-Y/B 7 0 ~ 15 G-Y/R 15 0 ~ 15 G-Y/B 2 0 ~ 15 LRGB2-LEVEL 7 0 ~ 15 PABL-LEVEL 15 0 ~ 15 BLK-BOTTOM 15 0 ~ 15 SUB-SHP 3 0~3 SUB-FO 2 0~3 P.CG V-AMP OFFSET REMARK PICT. IMPROVE 4-4 REMARK Samsung Electronics Alignment and Adjustments PICT. IMPROVE FUNCTION INITIAL DATA RANGE PRE-OVER 3 0~3 LT1-LEVEL 2 0~3 VM-LEVEL 2 0~3 VM-DELAY 3 0~3 DC-TRAN 3 0~3 D-PIC 3 0~3 DCTI 8 0 ~ 255 BPF-LPF 72 0 ~ 255 HPE-CORING 8 0 ~ 255 INITIAL DATA RANGE SYSTEM 2 0~3 CR-OFFSET1 7 0 ~ 15 CB-OFFSET1 9 0 ~ 15 R-Y/R 2 0 ~ 15 R-Y/B 15 0 ~ 15 G-Y/R 7 0 ~ 15 G-Y/B 0 0 ~ 15 SUB-SHP 0 0~3 SUB-FO 0 0~3 PRE-OVER 0 0~3 LT1-LEVEL 0 0~3 VM-LEVEL 0 0~3 VM-DELAY 0 0~3 DC-TRAN 3 0~3 D-PIC 3 0~3 REMARK PICT. IMPROVE FUNCTION Samsung Electronics REMARK 4-5 Alignment and Adjustments PICT. IMPRV. SECA FUNCTION INITIAL DATA RANGE CR-OFFSET1 6 0 ~ 15 CB-OFFSET1 11 0 ~ 15 R-Y/R 2 0 ~ 15 R-Y/B 15 0 ~ 15 G-Y/R 7 0 ~ 15 G-Y/B 0 0 ~ 15 INITIAL DATA RANGE CR-OFFSET1 7 0 ~ 15 CB-OFFSET1 9 0 ~ 15 CT1-LEVEL 1 0~3 DCTI 0 0 ~ 255 BPF-LPF 72 0 ~ 255 HPE-CORING 8 0 ~ 255 INITIAL DATA RANGE SYSTEM 0 0~3 CLP-MASK 0 0~3 DTV-SYNC 0 0 ~ 255 CR-OFFSET1 0 0 ~ 15 CB-OFFSET1 0 0 ~ 15 CTI-LEVEL 0 0~3 R-Y/R 0 0 ~ 15 R-Y/B 0 0 ~ 15 G-Y/R 0 0 ~ 15 REMARK PICT. IMPRV. DVD FUNCTION REMARK PICT. IMPRV. 480p FUNCTION 4-6 REMARK Samsung Electronics Alignment and Adjustments PICT. IMPRV. 480P FUNCTION INITIAL DATA RANGE G-Y/B 0 0 ~ 15 SUB-SHP 0 0~3 SUB-FO 0 0~3 PRE-OVER 0 0~3 LTI-LEVEL 0 0~3 VM-LEVEL 0 0~3 VM-DELAY 0 0~3 DC-TRAN 0 0~3 D-PIC 0 0~3 INITIAL DATA RANGE SYSTEM 0 0~ 3 CLP-MSK 0 0~ 3 DTV-SYNC 0 0 ~ 255 CR-OFFSET1 0 0 ~ 15 CB-OFFSET1 0 0 ~ 15 CTI-LEVEL 0 0~ 3 R-Y/R 0 0 ~ 15 R-Y/B 0 0 ~ 15 G-Y/R 0 0 ~ 15 G-Y/B 0 0 ~ 15 SUB-SHP 0 0 ~ 15 SIB-FO 0 0~3 PRE-OVER 0 0~3 LTI-LEVEL 0 0~ 3 VM-LEVEL 0 0~3 VM-DELAY 0 0~3 DC-TRAN 0 0~3 D-PIC 0 0~3 REMARK PICT. IMPRV. 1080 FUNCTION Samsung Electronics REMARK 4-7 Alignment and Adjustments SIM-826HEW OPTION-BYTE SP47W3HF SP55W3HF SP65W3HF REMARK WIDE WIDE WIDE WIDE <--> 4:3 LANGUAGE GROUP EUROPE EUROPE EUROPE EUROPE <--> ASIA LANGUAGE ENGLISH ENGLISH ENGLISH EIGHTEEN LANGUAGES ON ON ON ON <--> OFF SCART SCART SCART SCART <--> RCA VGA OFF OFF OFF ON <--> OFF PLUG&PLAY ON ON ON ON <--> OFF DOLBY PROLOGIC ON ON ON ON <--> OFF PIP ON ON ON ON <--> OFF CW/CS CW CW CW CW <--> CS LNA ON ON ON ON <--> OFF CHILD-LOCK ON ON ON ON <--> OFF HP JACK IDENT OFF OFF OFF ON <--> OFF TOP TTX OFF OFF OFF ON <--> OFF HIGH DEVIATION ON ON ON ON <--> OFF W-EUROPE W-EUROPE W-EUROPE ON ON ON STANDARD STANDARD OPTION BYTE CRT ATM SCRT/RCA E-EUROPE -> RUSSIAN -> ARABIC TTX GROUP GARRIER MUTE -> ICELANDIC -> HEBREW ON <--> OFF STANDARD -> SPORT -> MILD STANDARD 4-8 STANDARD -> NATURAL -> CUSTOM -> NDEN Samsung Electronics Alignment and Adjustments 4-4-2 CS MODEL Service Mode Deflection Video Adjust1 Video Adjust2 NTSC OFFSET & CG DW PIP & OTHERS OPTION RESET DEFLECTION FUNCTION INITIAL DATA RANGE V Shift 124 0 ~ 255 V AMP 134 0 ~ 255 V Lin 11 0 ~ 255 V SC 104 0 ~ 255 V EHT 0 0 ~ 255 H AMP 161 0 ~ 255 Pin Phase 143 0 ~ 255 Pin AMP 70 0 ~ 255 Up Corner 128 0 ~ 255 Low Corner 128 0 ~ 255 H EHT 0 0 ~ 255 H Shift 80 0 ~ 127 V Angle 124 0 ~ 255 V BOW 128 0 ~ 255 H Sync Phase 128 0 ~ 255 Samsung Electronics REMARK 4-9 Alignment and Adjustments VIDEO ADJUST1 FUNCTION INITIAL DATA RANGE Red Cutoff 31 0 ~ 63 Green Cutoff 31 0 ~ 63 Blue Cutoff 31 0 ~ 63 Red Drive 31 0 ~ 63 Green Drive 31 0 ~ 63 Blue Drive 31 0 ~ 63 Sub Bright 31 0 ~ 63 Sub Contrast 7 0 ~ 15 Sub Color 15 0 ~ 15 Sut Tint 7 0 ~ 15 RYR 3 0 ~ 15 RYB 7 0 ~ 15 GYR 15 0 ~ 15 GYB 2 0 ~ 15 Gamma 12 0 ~ 15 P.YC Delay 7 0~8 INITIAL DATA RANGE SUB Sharp 3 0~3 Sharp FO 2 0~3 Prev Over 3 0~3 LT1 2 0~3 CT1 1 0~3 VM-Level 2 0~3 VM-Delay 3 0~3 DC-TRAN 3 0~3 D Picture 3 0~3 H Width 1 0~3 REMARK VIDEO ADJUST2 FUNCTION 4-10 REMARK Samsung Electronics Alignment and Adjustments VIDEO ADJUST2 FUNCTION INITIAL DATA RANGE H Time Mask 1 0~3 ABL Mode 1 0~3 ABL TH 1 0~3 TTX Position 5 0 ~ 40 TTX Contrast 200 0 ~ 255 VSU 3 0 ~ 15 RGB Bright 0 0 ~ 127 RGB Contrast 24 0 ~ 63 Melody Volume 10 0 ~ 20 INITIAL DATA RANGE Offset V Shift 2 -64 ~ 63 Offset V AMP 0 -64 ~ 63 Offset H AMP 6 -64 ~ 63 Offset H Shift 4 -64 ~ 63 Cg R Contrast 100 0 ~ 100 Cg G Contrast 60 0 ~ 100 Cg B Contrast 10 0 ~ 100 Cg VAO PAL 24 0 ~ 100 Cg VAO NTSC 24 0 ~ 100 REMARK NTSC OFFSET & CG FUNCTION Samsung Electronics REMARK 4-11 Alignment and Adjustments DW PIP & OTHERS ITEM FUNCTION INITIAL DATA RANGE REMARK PIP VSTR VPC3230 0 X 0087 7 0 ~ 15 0 ~ 15 PIP HSTR VPC3230 0 X 008A 7 0 ~ 15 0 ~ 15 PIP Contrast VPC3230 fp 0 X 0053 48 0 ~ 63 0 ~ 63 DW 43 BCKPOS SDA9280 0 X 09 148 0 ~ 255 0 ~ 255 DW 43 BCKWID SDA9280 0 X 0A 61 0 ~ 255 0 ~ 255 Cr offset1 CXA2101 0 X 0F D7:D4 10 0 ~ 15 0 ~ 15 Cb offset1 CXA2101 0 X 0F D3:D0 10 0 ~ 15 0 ~ 15 Cr offset2 CXA2101 0 X 10 D7:D4 7 0 ~ 15 0 ~ 15 Cb offset2 CXA2101 0 X 10 D7:D4 7 0 ~ 15 0 ~ 15 SDA9280 LPF SDA9280 0 X 04 D6:D4 4 0~7 0~7 SDA9280 BPF SDA9280 0 X 04 D3:D0 12 0 ~ 15 0 ~ 15 SDA9280 HPF SDA9280 0 X 05 D3:D0 10 0 ~ 15 0 ~ 15 SDA9280 0 X 05 D6:D4 4 0~7 0~7 SDA9400 Y NR SDA9400 0 X 1E D7:D4 15 0 ~ 15 0 ~ 15 SDA9400 C NR SDA9400 0 X 10 D3:D0 15 0 ~ 15 0 ~ 15 SDA9280 CORING/PHACOM SIM-816HC OPTION-BYTE SP43T6HF SP47W3HF SP55W3HF REMARK DOLBY DOLBY DOLBY DOLBY <--> A2/NICAM <--> V-DOLBY WIDE OFF OFF OFF ON <--> OFF SCART1 OFF OFF OFF ON <--> OFF PC ON ON ON ON <--> OFF AUTO FM ON ON ON ON <--> OFF DOUBLE DOUBLE DOUBLE OFF <--> 1-TUNER <--> 2-TUNER <--> DOUBLE ON ON ON ON <--> OFF OPTION BYTE SOUND PIP HIGH DEVIATION 4-12 Samsung Electronics Alignment and Adjustments 4-4-3 W3 EU FACTORY DATA Y.C DELAY VIDEO ADJUSTMENT NO ITEM DEFAULT VALUE CONTROL IC NO ITEM DEFAULT VALUE CONTROL IC 0 R Drive 29 (0 ~ 63) CXA2101 0 PAL-B/G 6 (0 ~15) SDA9280 1 B Drive 36 (0 ~ 63) CXA2101 1 PAL-D/K/L 8 (0 ~15) SDA9280 2 G Drive 32 (0 ~ 63) CXA2101 2 PAL-I 8 (0 ~15) SDA9280 3 Gamma 8 (0 ~ 15) CXA2101 3 SECAM-B/G 5 (0 ~15) SDA9280 4 R Cutoff 31 (0 ~ 63) CXA2101 4 SECAM-D/K/L 7 (0 ~15) SDA9280 5 B Cutoff 15 (0 ~ 63) CXA2101 5 NTSC 6 G Cutoff 32 (0 ~ 63) CXA2101 6 PAL-AV 6 (0 ~15) SDA9280 7 Sub Contrast 15 (0 ~ 63) CXA2101 7 SECAM-AV 4 (0 ~15) SDA9280 8 Sub Bright 28 (0 ~ 63) CXA2101 8 NTSC-AV 5 (0 ~15) SDA9280 9 Sub Color 9 (0 ~ 63) CXA2101 9 RGB 7 (0 ~15) SDA9280 10 Sub Tint 9 (0 ~ 63) CXA2101 10 DVD 9 (0 ~15) SDA9280 11 V Peaking 8 (0 ~ 63) VPC3230 11 YC 9 (0 ~15) SDA9280 12 TTX Contrast 7 (0 ~ 63) CXA2101 13 TTX Bright 0 (0 ~ 63) CXA2101 14 PIP Contrast 43 (0 ~ 63) VPC3230 15 Not used - - 16 Cg R Contrast 31 (0 ~ 63) CXA2101 17 Cg G Contrast 31 (0 ~ 63) CXA2101 18 Cg B Contrast 15 (0 ~ 63) CXA2101 Samsung Electronics - - 4-13 Alignment and Adjustments DEFIECTION NORMAL (When a NTSC signal is input) DEFIECTION NORMAL (When a PAL signal is input) NO ITEM DEFAULT VALUE CONTROL IC NO ITEM DEFAULT VALUE CONTROL IC 0 P.V-Size -40 (-128 ~ 127) SDA9361 0 N.V-Size -40 (-128 ~ 127) SDA9361 1 P.V-Sft -34 (-128 ~ 127) SDA9361 1 N.V-Sft -34 (-128 ~ 127) SDA9361 2 P.V-Lin 0 (-128 ~ 127) SDA9361 2 N.V-Lin 0 (-128 ~ 127) SDA9361 3 P.V-Corr 0 (-128 ~ 127) SDA9361 3 N.V-Corr 0 (-128 ~ 127) SDA9361 4 P.EW-Wht 44 (-128 ~ 127) SDA9361 4 N.EW-Wht 44 (-128 ~ 127) SDA9361 5 P.EW-Pbl -27 (-128 ~ 127) SDA9361 5 N.EW-Pbl -27 (-128 ~ 127) SDA9361 6 P.H-Sft 0 (-63 ~ 64) SDA9361 6 N.H-Sft 0 (-63 ~ 64) SDA9361 7 P.EW-Tpz 0 (-128 ~ 127) SDA9361 7 N.EW-Tpz 0 (-128 ~ 127) SDA9361 8 P.Bow 0 (-128 ~ 127) SDA9361 8 N.Bow 0 (-128 ~ 127) SDA9361 9 P.Angle 0 (-128 ~ 127) SDA9361 9 N.Angle 0 (-128 ~ 127) SDA9361 10 P.EW-UpCr 0 (-128 ~ 127) SDA9361 10 N.EW-UpCr 0 (-128 ~ 127) SDA9361 11 P.EW-LoCr 0 (-128 ~ 127) SDA9361 11 N.EW-LoCr 0 (-128 ~ 127) SDA9361 12 P.Hor-EHT 0 (0 ~ 255 SDA9361 12 N.Hor-EHT 0 (0 ~ 255 SDA9361 13 P.Ver-EHT 0 (0 ~ 255) SDA9361 13 N.Ver-EHT 0 (0 ~ 255) SDA9361 14 P.Int.Vol.Ref 0 (-16 ~ 15) SDA9361 14 N.Int.Vol.Ref 0 (-16 ~ 15) SDA9361 10 (-128 ~ 127) SDA9361 15 N.Hsync Delay 10 (-128 ~ 127) SDA9361 16 P.PIP H-Position 7 (0 ~ 15) VPC3230 16 N.PIP H-Position 7 (0 ~ 15) VPC3230 17 P.PIP V-Position 7 (0 ~ 15) VPC3230 17 N.PIP V-Position 7 (0 ~ 15) VPC3230 15 P.Hsync Delay 18 P.Not used - - 18 N.Not used - - 19 P.Not used - - 19 N.Not used - - 30 (-128 ~ 127) SDA9361 30 (-128 ~ 127) SDA9361 20 P.CG V-amp Offset 4-14 20 N.CG V-amp Offset Samsung Electronics Alignment and Adjustments PICT. IMPROVE NO ITEM 0 Limit Level 3 (0 ~ 3) Luminance signal edge enhancement setting CXA2101 1 System 2 (0 ~ 3) Signal frequency band switching CXA2101 2 CLP-MSK 0 (0 ~ 3) Switching of clamping pulse width in various ways CXA2101 3 ABL-MODE 3 (0 ~ 3) Switching of ABL mode CXA2101 4 ABL-TH 1 (0 ~ 3) Adjustment of threshold voltage for ABL-IN input CXA2101 5 DTV-SYNC 9 (0 ~ 255) DTV-Sync CXA2101 6 Cr-Offset1 9 (0 ~ 15) For canceling the offset between CrCb of IN1and SEL IN systems CXA2101 7 Cb-Offset1 9 (0 ~ 15) For canceling the offset between CrCb of IN1and SEL IN systems CXA2101 8 Cr-Offset2 9 (0 ~ 15) For canceling the offset between CrCb of EXT systems CXA2101 9 Cb-Offset2 7 (0 ~ 15) For canceling the offset between CrCb of EXT systems CXA2101 10 CTI-Level 1 (0 ~ 3) Color difference signal edge enhancement setting CXA2101 11 R-Y/R 2 (0 ~ 15) R-Y axis +(R-Y) component setting CXA2101 12 R-Y/B 5 (0 ~ 15) R-Y axis -(B-Y) component setting CXA2101 13 G-Y/R 10 (0 ~ 15) G-Y axis -(R-Y) component setting CXA2101 14 G-Y/B 7 (0 ~ 15) G-Y axis -(B-Y) component setting CXA2101 15 LRGB2-Level 5 (0 ~ 15) LRGB2 system picture level control CXA2101 16 PABL-Level 14 (0 ~ 15) Setting of level detection DC at RGB-OUT of PEAK-ABL CXA2101 17 BLK-Bottom 0 (0 ~ 15) RGB-OUT bottom limiter level control(valid when BLKSW = 1) CXA2101 18 SUB-SHP 2 (0 ~ 3) Sharpness center control CXA2101 19 SUB-FO 2 (0 ~ 3) Sharpness fo setting CXA2101 20 PRE-OVER 3 (0 ~ 3) Presoot to overshoot ratio setting CXA2101 21 LTI-Level 1 (0 ~ 3) Luminance signal edge enhancement setting CXA2101 22 VM-Levle 2 (0 ~ 3) VM-OUT level control CXA2101 23 VM-Delay 0 (0 ~ 3) VM-OUT phase control CXA2101 24 DC-TRAN 3 (0 ~ 3) Y system DC transmission ratio setting CXA2101 25 D-PIC 3 (0 ~ 3) Dynamic picture(black expansion)control CXA2101 26 DCTI 8 (0 ~ 255) Digital Color Transition Improvement Control SDA9280 27 BPF-LPF Luminance Peaking Control -Gain of band-pass filter -Gain of low-pass filter SDA9280 28 HPF-Coing Luminance Peaking Control -Gain of high-pass filter -Gain of high-and band-pass filter SDA9280 Samsung Electronics DESCRIPTION DEFAULT VALUE 70 (0 ~ 255) 8 (0 ~ 255) CONTROL IC 4-15 Alignment and Adjustments PICT. IMPROVE NO ITEM DEFAULT VALUE DESCRIPTION 29 NR-Luminance 8 (0 ~ 14) Luminance Noise Reduction SDA9400 30 NR-Chrominace 6 (0 ~ 14) Chrominance Noise Reduction SDA9400 CONTROL IC PICT. IMPROVE. VGA(NOT USED) NO ITEM 0 System 1 Cr-Offset1 2 DESCRIPTION DEFAULT VALUE 2 (0 ~ 3) CONTROL IC Signal frequency band switching CXA2101 9 (0 ~ 15) For canceling the offset between CrCb of IN1 and SEL IN systems CXA2101 Cb-offset1 9 (0 ~ 15) For canceling the offset between CrCb of IN1 and SEL IN systems CXA2101 3 R-Y/R 2 (0 ~ 15) R-Y axis +(R-Y) component setting CXA2101 4 R-Y/B 5 (0 ~ 15) R-Y axis -(B-Y) component setting CXA2101 5 G-Y/R 10 (0 ~ 15) G-Y axis -(R-Y) component setting CXA2101 6 G-Y/B 7 (0 ~ 15) G-Y axis -(B-Y) component setting CXA2101 7 SUB-SHP 2 (0 ~ 3) Sharpness center control CXA2101 8 SUB-FO 3 (0 ~ 3) Sharpness fo setting CXA2101 9 PRE-OVER 3 (0 ~ 3) Preshoot to overshoot ratio setting CXA2101 10 LTI-Level 1 (0 ~ 3) Luminance signal edge enhancement setting CXA2101 11 VM-Level 2 (0 ~ 3) VM-OUT level control CXA2101 12 VM-Delay 0 (0 ~ 3) VM-OUT phase control CXA2101 13 DC-TRAN 2 (0 ~ 3) Y system DC transmission ratio setting CXA2101 14 D-PIC 3 (0 ~ 3) Dynamic picture(black expansion)control CXA2101 4-16 Samsung Electronics Alignment and Adjustments PICT. IMPROVE. SECAM NO ITEM DEFAULT VALUE DESCRIPTION CONTROL IC 0 Cr-Offset1 7 (0 ~ 15) For canceling the offset between CrCb of IN1 and SEL IN systems CXA2101 1 Cb-offset1 11 (0 ~ 15) For canceling the offset between CrCb of IN1 and SEL IN systems CXA2101 2 R-Y/R 3 (0 ~ 15) R-Y axis +(R-Y) component setting CXA2101 3 R-Y/B 7 (0 ~ 15) R-Y axis -(B-Y) component setting CXA2101 4 G-Y/R 10 (0 ~ 15) G-Y axis -(R-Y) component setting CXA2101 5 G-Y/B 2 (0 ~ 15) G-Y axis -(B-Y) component setting CXA2101 PICT. IMPROVE. RGB NO ITEM DEFAULT VALUE DESCRIPTION CONTROL IC 0 Cr-Offset1 9 (0 ~ 15) For canceling the offset between CrCb of IN1 and SEL IN systems CXA2101 1 Cb-offset1 9 (0 ~ 15) For canceling the offset between CrCb of IN1 and SEL IN systems CXA2101 2 DCT1 0 (0 ~ 255) Digital Color Transition Improvement Control SDA9280 3 R-Y/R 2 (0 ~ 15) R-Y axis +(R-Y) component setting CXA2101 4 R-Y/B 5 (0 ~ 15) R-Y axis -(B-Y) component setting CXA2101 5 G-Y/R 10 (0 ~ 15) G-Y axis -(R-Y) component setting CXA2101 6 G-Y/B 7 (0 ~ 15) G-Y axis -(B-Y) component setting CXA2101 7 VM-Level 0 (0 ~ 3) VM-OUT level control CXA2101 8 VM-Delay 0 (0 ~ 3) VM-OUT phase control CXA2101 9 V-PEAKING 0 (0 ~ 12) Vertical Peaking VPC3230 10 BPF-LPF 72 (0 ~ 255) Luminance Peaking Control -Gain of band-pass filter -Gain of low-pass filter SDA9280 11 HPF-Coring 10 (0 ~ 255) Luminance Peaking Control -Gain of band-pass filter -Gain of low-pass filter SDA9280 Samsung Electronics 4-17 Alignment and Adjustments PICT. IMPROVE. DVD NO ITEM DEFAULT VALUE DESCRIPTION CONTROL IC 0 Cr-Offset1 9 (0 ~ 15) For canceling the offset between CrCb of IN1 and SEL IN systems CXA2101 1 Cb-offset1 9 (0 ~ 15) For canceling the offset between CrCb of IN1 and SEL IN systems CXA2101 2 DCT1 0 (0 ~ 255) Digital Color Transition Improvement Control SDA9280 3 R-Y/R 2 (0 ~ 15) R-Y axis +(R-Y) component setting CXA2101 4 R-Y/B 5 (0 ~ 15) R-Y axis -(B-Y) component setting CXA2101 5 G-Y/R 10 (0 ~ 15) G-Y axis -(R-Y) component setting CXA2101 6 G-Y/B 7 (0 ~ 15) G-Y axis -(B-Y) component setting CXA2101 7 VM-Level 1 (0 ~ 3) VM-OUT level control CXA2101 8 VM-Delay 0 (0 ~ 3) VM-OUT phase control CXA2101 9 V-PEAKING 0 (0 ~ 12) Vertical Peaking VPC3230 10 BPF-LPF 72 (0 ~ 255) Luminance Peaking Control -Gain of band-pass filter -Gain of low-pass filter SDA9280 11 HPF-Coring 10 (0 ~ 255) Luminance Peaking Control -Gain of high-pass filter -Gain of high-and band-pass filter SDA9280 PICT. IMPROVE. YC NO ITEM DEFAULT VALUE DESCRIPTION CONTROL IC 0 Cr-Offset1 9 (0 ~ 15) For canceling the offset between CrCb of IN1 and SEL IN systems CXA2101 1 Cb-offset1 9 (0 ~ 15) For canceling the offset between CrCb of IN1 and SEL IN systems CXA2101 2 DCT1 0 (0 ~ 255) Digital Color Transition Improvement Control SDA9280 3 R-Y/R 2 (0 ~ 15) R-Y axis +(R-Y) component setting CXA2101 4 R-Y/B 5 (0 ~ 15) R-Y axis -(B-Y) component setting CXA2101 5 G-Y/R 10 (0 ~ 15) G-Y axis -(R-Y) component setting CXA2101 6 G-Y/B 7 (0 ~ 15) G-Y axis -(B-Y) component setting CXA2101 7 VM-Level 1 (0 ~ 3) VM-OUT level control CXA2101 8 VM-Delay 0 (0 ~ 3) VM-OUT phase control CXA2101 9 V-PEAKING 0 (0 ~ 12) Vertical Peaking VPC3230 10 BPF-LPF 72 (0 ~ 255) Luminance Peaking Control -Gain of band-pass filter -Gain of low-pass filter SDA9280 11 HPF-Coring 10 (0 ~ 255) Luminance Peaking Control -Gain of high-pass filter -Gain of high-and band-pass filter SDA9280 4-18 Samsung Electronics Alignment and Adjustments P.STD CHANGE NO ITEM DESCRIPTION DEFAULT VALUE CONTROL IC 0 STD Bright 32 (0 ~ 63) Standard Mode Brightness CXA2101 1 STD Contrast 42 (0 ~ 63) Standard Mode Contrast CXA2101 2 STC Color 32 (0 ~ 63) Standard Mode Color CXA2101 3 STD Sharpness 32 (0 ~ 63) Standard Mode Sharpness CXA2101 4 STD Tint 0 (-31 ~ 31) Standard Mode Tint VPC3230 5 STD Colortone Standard Mode Colortone CXA2101 6 Sports Bright 32 (0 ~ 63) Sports Mode Brightness CXA2101 7 Sports Contrast 51 (0 ~ 63) Sports Mode Contrast CXA2101 8 Sports Color 32 (0 ~ 63) Sports Mode Color CXA2101 9 Sports Sharpness 38 (0 ~ 63) Sports Mode Sharpness CXA2101 10 Sports Tint 0 (-31 ~ 31) Sports Mode Tint VPC3230 11 Sports Colortone Sports Mode Colortone CXA2101 12 Mild Bright 35 (0 ~ 63) Mild Mode Brightness CXA2101 13 Mild Contrast 32 (0 ~ 63) Mild Mode Contrast CXA2101 14 Mild Color 32 (0 ~ 63) Mild Mode Color CXA2101 15 Mild Sharpness 28 (0 ~ 63) Mild Mode Sharpness CXA2101 16 Mild Tint 0 (-31 ~ 31) Mild Mode Tint VPC230 17 Mild Colortone 1 (0 ~ 4) Mild Mode Colortone CXA2101 18 Natural Bright 28 (0 ~ 63) Natural Mode Brightness CXA2101 19 Natural Contrast 63 (0 ~ 63) Natural Mode Contrast CXA2101 20 Natural Color 32 (0 ~ 63) Natural Mode Color CXA2101 21 Natural Sharpness 45 (0 ~ 63) Natural Mode Sharpness CXA2101 22 Natural Tint 0 (-31 ~ 31) Natural Mode Tint VPC3230 23 Natural Colortone Natural Mode Colortone CXA2101 24 VGA Bright 32 (0 ~ 63) Not used CXA2101 25 VGA Contrast 32 (0 ~ 63) Not used CXA2101 26 RGB Color 5 (0 ~ 255) RGB Mode Color VPC3230 27 RGB Color_L 209 (0 ~ 255) RGB Mode Color VPC3230 28 RGB Tint RGB Mode Tint VPC3230 29 RGB Bri_Cont RGB Mode Brightness, Contrast VPC3230 Samsung Electronics 0 (0 ~ 4) 3 (0 ~ 4) 3 (0 ~ 4) 0 (0 ~ 255) 27 90 ~ 255) 4-19 Alignment and Adjustments P.STD CHANGE NO ITEM DEFAULT VALUE 30 RGB Bri-Cont_L 68 (0 ~ 255) 31 FB Gain 32 Slicer Level 144 (0 ~ 255) 15 (0 ~ 255) DESCRIPTION CONTROL IC RGB Mode Brightness, Contrast VPC3230 Fast Blanking Signal Gain Control VPC3230 Slicer Level Control VPC3230 SIDE PANEL ADJUST NO ITEM 0 Side Panel Pos. 1 Side Panel Width 2 Side Panel Level 3 4 4-20 DESCRIPTION DEFAULT VALUE 153 (0 ~ 255) CONTROL IC Side Panel Position Control SDA9280 Side Panel Width Control SDA9280 7 (0 ~ 15) Side Panel Luminance Control SDA9280 Side Panel B-Y 0 (0 ~ 15) Side Panel Chrominance Control SDA9280 Side Panel R-Y 0 (0 ~ 15) Side Panel Chrominance Control SDA9280 69 (0 ~ 255) Samsung Electronics Alignment and Adjustments 4-5 Screen Change (When adjusting I2C Bus Geometric items) 1 V SHIFT 6 V SIZE 2 V LINEARITY 7 V - S - CORRECTION 3 H SIZE 8 PIN PHASE 4 PIN AMP 9 H SHIFT 5 V ANGLE 10 V BOW Samsung Electronics 4-21 Alignment and Adjustments 4-6 Other Adjustments 4-6-1 Screen Adjustment 3. Select SBT by pressing the Volume +/- keys. 1. Warm up the TV for at least 30 minutes. 4. Adjust so that the 63 step on the right side of the screen is not seen (Use the Volume +/keys). 2. Turn to the Video Mode (No Signal) using a remote-control. 5. Press the Menu key to exit. 3. Connect an oscilloscope to RK,GK,BK. 4. Adjust the VR (VR501, VR531, VR561) screen so that RK, GK, BK pulse is 20Vp-p each. (Turn the R,G,B VR screen fully counterclockwise in the area of each flyback line.) 4-6-4 High Voltage (29KV) Check PRECAUTION 1. Input a lion head pattern. 2. Select “STANDARD” video mode. 4-6-2 White Balance Adjustment 3. Warm up the TV for at least 10 minutes. 1. Select the “STANDARD” video mode. 4. Use a 1000:1 probe. 2. Input 100% white pattern. 3. In the stand-by mode, press the remote-control keys in the following sequence: Displsy → Menu → Mute → Power ON 4. Warm up the TV for at least 30 minutes. 5. Input a 10-step signal. 6. R-cut off, B-cut off, and G-cut off by pressing the Volume +/- keys. 7. Adjust the low light with viewing the dark side of the screen. ADJUSTMENT 1. Connect the (+) terminal of the 1000:1 probe to the high voltage distributor and the (-) terminal to GND (located on the deflection board). 2. Adjust RR471S (located on the deflection board) so that the digital meter indicates DC 29V ± 0.1V. 4-6-5 F.S. (Fail Safe) Adjustment 8. Select R-drive, G-drive, and B-drive by pressing the Volume +/- keys. Note : The finished product has a well-mounted VR (RR402S). If necessary, do the F.S. adjustments in the following sequence. 9. Adjust the high light with viewing the light side of the screen. 1. Use a digital multimeter. 10. If necessary, redo adjustments 6~9. 2. Connect the digital multimeter to the JIG pin (DZ482S) terminals 3. Adjust VR (RR402S) so that the voltage becomes 2.25V. 4. After the adjustments are complete, be sure to mount VR (RR402S) correctly. 11. Press the Menu key to exit. 4-6-3 Sub-Brightness Adjustment 1. Input a sub-brightness adjustment signal. (TOSHIBA PATTERN) 2. In the stand-by mode, press the remote-control keys in the following sequence : Displsy → Menu → Mute → Power ON 4-22 Samsung Electronics Alignment and Adjustments 4-6-6 F.S. (Fail Safe) Circuit Check 4-6-8 Lens Focus Adjustment Note : The F.S. Circuit check must be performed after servicing. PRECAUTIONS 1. Turn on the TV. 2. Select the “STANDARD” video mode. 3. Short F/S Test point (located on the SUB PCB). Then, both sound and picture disappear. (Note: Even if the shorted terminals are removed, both sound and picture do not appear. This proves the F.S. circuit is working. ) 1. Do this adjustment after the static focus adjustment and the tilt adjustment. 2. Select the “STANDARD” video mode. (Contrast:100, Brightness:50) 3. Input a crosshatch pattern. ADJUSTMENT 1. Loosen the lens screws. 4. To restore both sound and picture, turn off the TV and reset it after about 30 seconds. 2. Cover the two lenses that are not being adjusted. 4-6-7 Static Focus Adjustment 3. Adjust the lens, observing the color aberration vertically and horizontally within 3 blocks of the center of the crosshatch pattern. PRECAUTION 1. Select the “STANDARD” video mode. 4. When the lens is turned clockwise, the color aberration will change as follows: 2. Input a crosshatch pattern. 3. Cover the lenses that are not being adjusted. 4. Connect a convergence jig and read data. 5. Adjust the lens for best focus. (See Fig, 4-1, next page) STATIC FOCUS (CONTINUED) Vary the focus pack VR (Red, Blue) on the front cabinet. Adjust the TV for best possible focus around the center of the crosshatch pattern, without losing overall screen balance. Figure Crosshatch Pattern Examine these points together. Lens R G B Color Aberration Change Orange - Crimson Blue - Red Purple - Green 5. Green lens adjustment: Set the lens at the point where Blue just changes to Red. If the color aberration is irregular throughout the picture screen, adjust the lens to show Red color aberration (approximately 1~3 mm area) within a 3-block grid around the horizontal center-line. If the color aberration is irregular, adjust the lens as shown in the diagram below. (Accurate alignment of Green is important for overall color quality.) 6. Red lens adjustment Set the Red lens at the point where Orange becomes Crimson. 7. Blue lens adjustment Set the Blue lens at the point where Purple becomes Green. Examine these points together Fig. 4-1 Crosshatch Pattern. P L1 L2 RED ABERRATION BLUE ABERRATION L1, L2_< P Fig. 4-2 Color Aberration Samsung Electronics 4-23 Alignment and Adjustments 4-6-9 Horizontal Dynamic Focus Adjustment PRECAUTION 1. Input a crosshatch pattern. 2. Select the “STANDARD” video mode. 3. Warm up the set for at least 10 minutes. ADJUSTMENT 1. Cover the Red and Blue lenses. 2. Use a digital multimeter. 3. Connect the '+' terminal of digital multimeter to D-Focus and the '-' terminal to GND. 4. Adjust L434 located on the sub PCB so that the digital multimeter indicates AC690 20Vp-p.(WIDE AC600 20Vp-p) 5. Balance the left and right sides of the dynamic focus lines. 4-24 Samsung Electronics Alignment and Adjustments 4-7 SCREEN-JIG 4-7-1 43T6 Normal Mode N o r mal 4 :3 M o d e Sc reen Size : X 873, Y 655 (X:378= 9*2+ 30* 12, Y: 440=28*2+ 64* 6) 2 0 .7 9 m m 6 9 .2 9 m m 2 0 .7 9 m m 4 1 .6 8 m m 9 5 .2 7 m m 4 1 .6 8 m m 4-7-2 54T6 Normal Mode N o r m al 4 : 3 m o d e Sc reen Size : X 1098.4, Y 827.4 (X :378=9* 2+ 30*12, Y:440=28* 2+ 64* 6) 2 6 .1 5 m m 8 7 .1 7 m m 2 6 .1 5 m m 5 2 .6 5 m m 1 2 0 .3 5 m m 5 2 .6 5 m m Samsung Electronics 4-25 Alignment and Adjustments 4-7-3 47W3 Normal Mode N o r m al 4 : 3 m o d e Sc reen Size : X 1045, Y 588 (X:378= 9* 2+ 30* 12, Y: 440=28*2+ 64* 6) 2 4 .8 8 m m 8 2 .9 4 m m 2 4 .8 8 m m 3 7 .4 2 m m 8 5 .5 3 m m 3 7 .4 2 m m 4-7-4 55W3 Normal Mode N o r m al 4 : 3 m o d e Sc reen Size : X 1225, Y 686 (X:378= 9* 2+ 30* 12, Y: 440=28*2+ 64* 6) 29.17mm 97.22mm 29.17mm 43.65mm 99.78mm 43.65mm 4-26 Samsung Electronics Alignment and Adjustments 4-7-5 65W3 Normal Mode N o r m al m o de Scr een Size : X 1442, Y 838 (X :378=9* 2+ 30*12, Y:440= 28* 2+ 64* 6) 3 4 .3 3 m m 1 1 4 .4 4 m m 3 4 .3 3 m m 5 3 .3 3 m m 1 2 1 .8 9 m m 5 3 .3 3 m m Samsung Electronics 4-27 Alignment and Adjustments 4-8 Remote Control for Servicing 4-8-1 WESTERN EUROPE Power 4-28 Samsung Electronics Alignment and Adjustments 4-8-2 CHINA Power Samsung Electronics 4-29 Alignment and Adjustments 4-8-3 KEY Function 1. R-SELECT Press to select RED color. 2. G-SELECT Press to select GREEN color. 3. B-SELECT Press to select BLUE color. 4. R-MUTE Press to mute RED color. 5. G-MUTE Press to mute GREEN color. 6. B-MUTE Press to mute BLUE color. 7. CANCEL KEY Press to revert to the previous data during the Convergence Adjustment. 8. TEST/NORMAL Press to check TV mode in the Convergence Mode. 9. LINE SHIFT Press to move a line up/down or left/right. 10. FACTORY DATA SELECT BUTTON Press to call the factory default values. 11. H/V DIRECTION SELECT BUTTON Press to switch the cursor direction horizontally or vertically. 12. SAVE BUTTON After the Convergence Adjustments are completed, press to save data. 13 EXIT BUTTON After the Convergence adjustments are completed, press to exit to TV mode. 4-30 Samsung Electronics Alignment and Adjustments 14. MOVE CURSOR FORWARD Press to move the cursor right or down. 15. MOVE CURSOR REVERSE JOYSTICK(Option Press to move the cursor left or up. ) 16. CONVERGENCE PICTURE MOVE BUTTON 17. CONVERGENCE MOVE BUTTON Press to move the convergence left ( ) or right ( ). 18. CONVERGENCE DATA ZERO BUTTON Press to zero the convergence correction data. 19. INITIAL DATA SET BUTTON Changes when applying Almighty-Cg, Module (How to extract the basic Cg Data) Model Name Basic Data Representative Model Number after entring the Cg-Mode 43” (43T6) SP43T6 5-436 (Press in regular order) 54” (54T6) SP54T6 5-546 (Press in regular order) 62” (62T6) SP62T6 5-626 (Press in regular order) 47”(47W3) SP47W3 5-479 (Press in regular order) 55”(55W3) SP55W3 5-559 (Press in regular order) 65”(65W3) SP65W3 5-659 (Press in regular order) Inch (Type) 20. Data Shift Button Samsung Electronics Screen Display Discription White Oval on the background (white circle) White Oval on the background (white border) White Oval on the background (white circle) White Oval on the background (white border) Press to transmit data(PAL Mode/NTSC Mode) 4-31 Alignment and Adjustments 4-9 Convergence Adjustment Special Notes ✏ A sensor is attached on the center of each side of the Convergence Mode pattern (see figure below). The sensors are required for normal Perfect Focus function. ✏ Use a screen jig to do the convergence adjustments correctly (Especially, perform correct convergence adjustments on the center of each side where a sensor is located.) ✏ Do the convergence adjustments correctly. Otherwise, any Perfect Focus error can happen. 1. Warm up the TV for a least 30 minutes. 2. Input an PAL Signal.(Use an antenna or AV source.) Make sure that deflection yoke are properly adjusted so that the center of Green, Red, Blue pattern is aligned on the center of screen jig. 3. Enter the Convergence Mode by Pressing the remote control keys in the following sequence: If OSD displayed as shown in figure below, press the key to exit. Then, redo step 3 to enter the Convergence Mode. After entering the Convergence Mode, Stand by for about five seconds before doing the adjustments. 4-32 Samsung Electronics Alignment and Adjustments Samsung Electronics 4-33 Alignment and Adjustments 4-34 Samsung Electronics Samsung Electronics 4-35 Alignment and Adjustments 4-36 Samsung Electronics Alignment and Adjustments 4-10 MICOM and Pins Voltage 4-10-1 Pin Layout(CW) AMP MUTE CENTER RESET BUS-STOP KEYS1 KEYS2 MAIN AFT SUB AFT VSSA A3 VDDA M3L CLK M3L DATA M3L ENABLE RXD IR P0.5 P0.6 P0.7 P2.3 P2.2 P2.1 P2.0 VSSA A3 VDDA P3.7 P3.6 P3.5 P3.4 P3.3 P3.2 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 D1 P3.1 D2 P3.0 D3 P1.6 PROTECT P1.5 ST-BY LED1 P1.4 TIMER LED2 P1.3 POWER P1.2 POWER2 P1.1 TXD P1.0 VSS VSS VDD VDD XTAL2 XTAL2 XTAL1 XTAL1 RESET RST NC ALE A16 A16 SDA30C264 P0.4 WP P0.3 SCL2 P0.2 SDA2 P0.1 SDA1 P0.0 SCL1 P4.1 A18 P4.0 A17 VDD VDDD VSS VSSD A2 A2 A1 A1 A0 A0 D3 D3 D2 D2 D4 D4 D1 D1 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 D7 D6 D0 D5 D7 D6 D0 D5 A5 A10 A10 A5 A6 A4 A6 A8 A4 A8 A7 A11 A11 A7 A13 A13 A12 A12 A14 A14 A15 A15 Samsung Electronics 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 4-37 Alignment and Adjustments 4-10-2 MICOM Pins(CW) PIN NO. 4-38 ITEM FUNCTION 1 D1 D1 2 D2 D2 3 D3 D3 4 PROTECT PROTECT 5 ST-BY LED ST-BY LED 6 TIMER LED TIMER LED 7 POWER POWER 8 POWER2 POWER2 9 TXD TXD 10 VSS VSS 11 VDD VDD 12 XTAL2 XTAL2 13 XTAL1 XTAL1 14 RESET RESET 15 NC NC 16 A16 A16 17 A15 A15 18 A14 A14 19 A12 A12 20 A13 A13 21 A7 A7 22 A8 A8 23 A6 A6 24 A9 A9 25 A5 A5 26 A11 A11 OUT VOLT Samsung Electronics Alignment and Adjustments PIN NO. ITEM FUNCTION 27 A4 A4 28 D10 D10 29 D7 D7 30 D6 D6 31 D0 D0 32 D5 D5 33 D1 D1 34 D4 D4 35 D2 D2 36 D3 D3 37 A0 A0 38 A1 A1 39 A2 A2 40 VSS VSS 41 VDD VDD 42 A17 A17 43 A18 A18 44 SCL1 SCL1 45 SDA1 SDA1 46 SDA2 SDA2 47 SCL2 SCL2 48 WP WP 49 AMP-MUTE AMP-MUTE 50 CENTER-MUTE CENTER-MUTE 51 BUS-STOP BUS-STOP 52 KEY1 KEY1 Samsung Electronics OUT VOLT 4-39 Alignment and Adjustments PIN NO. 4-40 ITEM FUNCTION 53 KEY2 KEY2 54 MAIN-AFT MAIN-AFT 55 SUB-AFT SUB-AFT 56 VSS VSS 57 A3 A3 58 VDD VDD 59 M3L CLK M3L CLK 60 M3L DAT M3L DATA 61 M3L ENABLE M3L ENABLE 62 NC NC 63 RXD RXD 64 IR IR OUT VOLT Samsung Electronics Alignment and Adjustments 4-10-3 Pin Layout(CS) W.P SDA2 SCL2 BUS-STOP SDA1 SCL1 S-RESET V-MUTE VDD 2.5V GND VDD 3.3V CVBS IN VDD 2.5V GND AFT SUB-AFT KEY2 KEY1 H-BLK V-BLK KEY3 PROTECT SCONT1 IR-IN D3 TIMER LED Samsung Electronics 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 S D A 5 5 5 X 52 51 50 49 48 47 46 45 SCONT 0 POWER 2 POWER S-MUTE DVD-CTL LENTER SPK-MUTE DTV-ID DVD-ID 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 VDD 3.3V GND VDD 2.5V OSD F/B OSD B OSD G OSD R VDD 2.5V GND X-OUT X-IN RESET D1 D2 VDD 3.3V GND RTXD ST-BY LED 4-41 Alignment and Adjustments 4-10-4 MICOM Pins(CS) PIN NO. 4-42 ITEM FUNCTION 1 W.P 2 SDA2 3 SCL2- 4 BUS-STOP I2 BUS STOP 5 SDA-1 DATA BUS LINE 6 SCL-1 CLOCK BUS LINE 7 S-RESET SOUND RESET 8 V-MUTE VIDEO SIGNAL MUTE 9 VDD VDD 2.5V 10 GND GND 11 VCC VCC 3.3V 12 CVBS CVBS IN 13 VDD VDD 2.5V 14 GND GND 15 MAIN-AFT MAIN TUNER AFT 16 SUB-AFT SUB AUTO FINE TURNING CONTROL 17 KEY2 KEY SCAN 2 18 KEY1 KEY SCAN 1 19 HSYNC HORIZONTAL SYNC INPUT 20 VSYNC VERTICAL SYNC INPUT 21 KEY3 KEY SCAN 3 22 PROTECT PROTECT PORT 23 S-CONTO SOUND MODE SELECT 24 IR IN REMOCON INPUT 25 D3 CONVERGENCE D3 26 TIMER-LED TIMER LED OUT VOLT Samsung Electronics Alignment and Adjustments PIN NO. ITEM FUNCTION 27 ST-BY-LEDD LED 28 RXD - 29 GND GND 30 VDD VDD 3.3V 31 D2 DATA BUS LINE 32 D1 CLOCK BUS LINE 33 /RESET RESET 34 XTAL1 XTAL1 35 XTAL2 XTAL2 36 GND GND 37 VDD VDD 2.5V 38 OSD R ON SCREEN DISPLAY RED OUTPUT 39 OSD G ON SCREEN DISPLAY GREEN OUTPUT 40 OSD B ON SCREEN DISPLAY BLUE OUTPUT 41 OSD F-B OSD BLAKING SIGNAL OUTPUT 42 VDD VDD 2.5V 43 GND GND 44 VDD VDD 3.3V 45 DVD-IDENT DVD-IDENT 46 DTV-INENT DTV-IDENT 47 CENTER SPK MUTE 48 MODE SELECT DVD MODE SELECT(480i/480p) 49 AMP-MUTE MAIN AMP MUTE 50 POWER POWERR ON/OFF RELAY CONTROL S-CONTO SOUND MODE SELECT OUT VOLT 51 52 Samsung Electronics 4-43 Alignment and Adjustments 4-10-5 Proscan Module (CS) PIN NO. 4-44 ITEM FUNCTION OUT VOLT 1 Pr/R Pr/R INPUT 2.0V 2 Y/G Y/G INPUT 2.0V 3 Pb/B Pb/B INPUT 2.0V 4 FB FAST BLANKING INPUT 0.25V 5 GND GND - 6 HC 5V INPUT - 7 VS1 VS1 INPUT - 8 GND GND - 9 SDA SERIAL DATA LINE 4.7V 10 SCL SERIAL CLOCK LINE 4.8V 11 5V 5V 12 27M OPTION 13 GND GND GND 14 5V- 5V- 5V- 15 H-OUT HORIZENTAL-OUT N.C 16 V-OUT VERTICAL-OUT N.C 17 SCP 18 EW EAST WEST OUT 19 V-BLK V-BLANKING 20 ABL ABL INPUT 2.15V 21 AD- VERTICAL DRIVE(-VOLTAGE) 2.95V 22 AD+ VERTICAL DRIVE(+VOLTAGE) 2.90V 23 H-BLK H-BLANKING INPUT 24 HD H-DRIVE OUT 1.6V 25 GND GND GND 26 PIP-RF - 27 PIP-C - 28 PIP-V/Y - 29 GND 30 CVBS-Y 5V - - GND 2.2V - - GND - Samsung Electronics Alignment and Adjustments PIN NO. ITEM FUNCTION OUT VOLT 31 CHR CHROMA 32 GND GND GND 33 PC-R N.C - 34 PC-G N.C - 35 PC-B N.C - 36 PC-H GND GND 37 PC-V OSD-R INPUT - 38 GND OSD-G INPUT - 39 OSD-R OSD-B INPUT - 40 OSD-G BLANK(MICOM OUT) - 41 OSD-B HALF TONE INPUT - 42 YS/YM VIDEO MUTE (V-CHIP ON) 4.72V 43 YS/YM GND GND 44 GND 9V 45 9V D-Pr INPUT - 46 HD-Pr D-Y INPUT - 47 HD-Y D-Pb INPUT - 48 HD-Pb N.C - 49 GND GND GND 50 R-OUT R-OUT - 51 G-OUT G-OUT - 52 B-OUT B-OUT - 53 GND GND GND 54 IK IK OUT 3.65V 55 GND SPOT OUT 56 GND GND GND 57 VM-Y VM-Y OUT 5.42V 58 YD N.C - 59 GND GND GND 60 CG-SYND CG-SYNC INPUT Samsung Electronics - 9V - - 4-45 Alignment and Adjustments PIN NO. 4-46 ITEM FUNCTION OUT VOLT 61 CG-B CG-B INPUT - 62 CG-G CG-G INPUT - 63 CG-R CG-R INPUT - 64 GND GND GND Samsung Electronics Alignment and Adjustments 4-10-6 Sound Module PIN NO. ITEM FUNCTION OUT VOLT 1 GND GND GND 2 GND GND GND 3 GND GND GND 4 S-RESET SOUND RESET - 5 MAIN-L MAIN LEFT OUT - 6 GND GND GND 7 GND GND GND 8 5V 5V 9 MAIN-R MAIN RIGHT OUT 10 GND GND GND 11 GND GND GND 12 GND GND GND 13 8V 8V 14 SCL-1 SERIAL CLOCK LINE 15 GND GND 16 SDA-1 SERIAL DATA LINE - 17 CENTER CENTER OUT - 18 GND GND GND 19 GND GNAD GND 20 12V 12V 12V 21 SURROUND SURROUND OUT 22 GND GND GND 23 GND GND GND 24 S-F1 S-F1(ANT1) 25 GND GND GND 26 GND GND GND 27 AV4-L-IN AV4 LEFT INPUT - 28 A-MONO-IN A-MONO INPUT - 29 GND GND GND 30 GND GND GND Samsung Electronics 5V - 8V GND - - 4-47 Alignment and Adjustments PIN NO. 4-48 ITEM FUNCTION OUT VOLT 31 AV4-R-IN AV4 RIGHT INPUT - 32 S-F2 S-F2(ANT2) - 33 GND GND GND 34 GND GND GND 35 GND GND GND 36 GND GND GND 37 EXT-L-IN EXTERNAL LEFT INPUT - 38 H-PHONE-L HEADPHONE LEFT OUT - 39 GND GND GND 40 GND GND GND 41 EXT-R-IN EXTERNAL RIGHT INPUT - 42 H-PHONE-R HEADPHONE RIGHT OUT - 43 GND GND GND 44 GND GND GND 45 GND GND GND 46 GND GND GND 47 AV2-L-IN AV2 LEFT INPUT - 48 MONITOR-L MONITOR OUT - 49 GND GND GND 50 GND GND GND 51 AV2-R-IN AV2 RIGHT INPUT - 52 MONITOR-R MONITOR OUT - 53 GND GND GND 54 GND GND GND 55 GND GND GND 56 GND GND GND 57 AV1-L-IN AV1 LEFT INPUT - 58 AV1-L-OUT AV1 LEFT OUTPUT - 59 GND GND GND 60 GND GND GND Samsung Electronics Alignment and Adjustments PIN NO. ITEM 61 AV1-R-IN AV1 RIGHT INPUT - 62 AV1-R-OUT AV1 RIGHT OUT - 63 GND GND GND 64 GND GND GND Samsung Electronics FUNCTION OUT VOLT 4-49 Alignment and Adjustments 4-10-7 CONV-Module PIN NO. 4-50 ITEM FUNCTION OUT VOLT 1 6V 6V 6V 2 GND GND GND 3 FOCUS N.C - 4 GND GND GND 5 D2 SDA - 6 D1 SCL - 7 GND GND GND 8 C-SYNC C-SYNC OUT 4.41V 9 R WHEN TEST PATTERN R OUT - 10 TEST-Y/G WHEN TEST PATTERN G OUT - 11 B WHEN TEST PATTERN B OUT - 12 D3 D3/NT-PAL SEL 13 CTRL CTRL 14 IR INPUT REMOCON 15 COMP COMP VIDEO OUTPUT 16 GND GND GND 17 GND GND GND 18 GND GND GND 19 BV BLUE VERTICAL OUT - 20 BH BLUE HORIZONTAL OUT - 21 GV GREEN VERTICAL OUT - 22 GH GREEN HORIZONTAL OUT - 23 RV RED VERTICAL OUT - 24 RH RED HORIZONTAL OUT - 25 GND GND GND 26 H-BLK H-BLANKING OUT 0.52V 27 V-BLK V-BLANKING OUT - 28 GND GND GND 29 N.C N.C - 30 -5.4V -5.4V -5.4V 0.2V 3V - Samsung Electronics Alignment and Adjustments PIN NO. ITEM FUNCTION OUT VOLT 31 5.4V 5.4V 5.4V 32 GND GND GND Samsung Electronics 4-51 Alignment and Adjustments MENO 4-52 Samsung Electronics Troubleshooting 5. Troubleshooting 5-1 Convergence Misaligned Normal Check CNZ01 out pin (BZ, BH, RV, RH, GV, GH) Check the output voltage and waveform of CN801, 803, CNZ02 on the Convergence Board Abnormal Normal Check the associated circuitry Samsung Electronics Abnormal Check Convergence Moudle 1. Check FD802S, FD855S, FD805S, FD806S On the Power Board 2. Check the output from H-BLK, V-BLK the Main Board 5-1 Troubleshooting 5-2 No Sound Check if CN601 is inserted normal Check IC665 output pins 2, 4 Abnormal Check IC665 input pin 5 normal Check IC665 Mute pin 5 normal Check IC665 output pins 7, 11 Abnormal Check IC601 input pins 35, 38 Abnormal Check CNS01 input pins 5, 9 Abnormal Check IC703 input pins Abnormal Abnormal Insert CN601 (Connector) normal Check Speaker Abnormal Check FD854S on the Power Board Abnormal Check the Mute circuit normal Check the Control normal Check the Control normal Check the Sound Module circuit normal Check IC703 Check CNS01 output pins 28 5-2 Samsung Electronics Troubleshooting 5-3 No Raster (Sound OK) Normal Check Heater Check CRT PCB pin 1 Check High Voltage Normal Check CN501 pins 1, 3, 5 Normal Check CN501 (Connector) Normal Check CN01 inpur pins 30, 31 Abnormal Check CNT02 input pins 19, 21 Abnormal Check IC02 input pin 24 Abnormal Check IC701 input pin 8 Normal Normal Check IC501, 531, 561 Abnormal Check CN501 (Connector) Normal Check Q473 HV-REG Abnormal Check Q473, IC471 Abnormal Check Q473, R437A Normal Check Q472 input pin "G"(HV-DRIVER) Normal Abnormal Check HV-OUT BLOCK Check HV-OUT BLOCK Check CN01 Normal Check CNT02 Normal Check IC02 Normal Abnormal Check CN01 Samsung Electronics Check IC701 5-3 MEMO 5-4 Samsung Electronics Exploded View & Parts List 6. Exploded View & Parts List 6-1 SP47W3HFX No Samsung Electronics Code No Description;Specification Q’ty S.N.A 1 TAPE-OPP MASKING 2 SPACER-COVER,DUST;W3,PS SHEET,T0.35 1 3 BRACKET-CRT,MAIN;54,SECC,T1.6,-,-,-,- 1 4 GUIDE-FLOW;54J8,J7,ABS,-,-,-,BLK,HB 1 S.N.A 5 HOLDER-SCREEN,R;47H1,ABS HB,GRAY 1 S.N.A 5 HOLDER-SCREEN,TB;W3,W1,ABS HB,L1102,BLK, 2 S.N.A 5 HOLDER-SCREEN,L;47H1,ABS HB,GRAY 1 S.N.A 6 CABINET-BACK,BOT;47W3,HIPS HB,BLK 1 7 CABINET-BACK,TOP;47W3,HIPS HB,BLK,DO 1 8 CABINET-BACK,SIDE;47.55W3,HIPS HB,BLK,DO 2 9 SCREEN-TINT;47W,1070*612,T=0.7,P=0.52 1 10 SCREEN-FRESNEL;47W,-,T2,1072*614,-,-,-,- 1 11 SUN SCREEN-AG;47W,-,T=82%,1072*614*2,-,- 1 12 MIRROR-FRONT;47W3,GLASS ,861*677*421,FSM 1 13 BRACKET-MIRROR;47W3,SECC,T1.0 1 S.N.A 14 ASSY CHASSIS;SP47W3HFX/BWT 1 S.N.A 15 ASSY-C/FRONT,MASK;,HB GRAY,SVM1126 TANTU 1 16 DOOR-RACK;47.55.65W3,HIPS HB,GRAY,SV808P 1 17 ASSY-CABINET,WOOD;,WOOD,CIS,47W3 1 18 ASSY SUB-PCB,A/V TERMINAL;W3,J52A,RUSSIA 1 19 ASSY-C/FRONT,BOT;,HB GRAY,SV808P+SVM1126 1 20 ASSY-CENTER,SPK;,W3 Remark S.N.A S.N.A 6-1 Exploded View & Parts List 6-2 SP55W3HFX No 6-2 Code No Description;Specification Q’ty S.N.A 1 ASSY-C/FRONT,MASK;,HIPS HB,GRAY SVM1126 1 2 ASSY-C/FRONT,BOT;,HIPS HB,GRAY SV808P+SV 1 3 ASSY-DOOR,RACK;,HB GRAY,SV808P+SVM1126,W 1 4 ASSY-CENTER,SPK;,W3 1 5 SUN SCREEN-AG;55W,-,T=82%,1251*712*2,-,- 1 6 SCREEN-FRESNEL;55W,-,T2,1251*712,-,-,-,- 1 8 ASSY-CABINET,WOOD;,WOOD M-EAST,55W3 1 9 CABINET-BACK,SIDE;47.55W3,HIPS HB,BLK,DO 2 10 HOLDER-SCREEN,TB;55W3,ABS HB,L1282,BLK 2 10 HOLDER-SCREEN,L;55W3,ABS HB,BLK 1 10 HOLDER-SCREEN,R;55W3,ABS HB,BLK 1 11 ASSY SUB-PCB,A/V FRONT;SP47W3HFX/XEG,J52 1 12 ASSY CPT-B;P16LSG03BMB,55,+380MGSSM-100 1 13 SPACER-COVER,DUST;W3,PS SHEET,T0.35 1 14 MIRROR-FRONT;55W9,FSM,1027*799*540 1 15 BRACKET-FRAME,MIRROR L;55W9,SECC,T1.6,BL 1 16 BRACKET-FRAME,MIRROR R;55W9,SECC,T1.6,BL 1 17 SPACER-MIRROR,TOP;50J6,PVC HB,BLK,L1020 1 18 SPACER-MIRROR,L;50J6,PVC HB,BLK,L1020 1 19 SPACER-MIRROR,BOT;50J6,PVC HB,L799,BLK 1 20 SPACER-MIRROR,R;50J6,PVC HB,BLK,L1020 1 21 BRACKET-MIRROR,BOT;55W9,SECC,T1.0 1 22 BRACKET-MIRROR,TOP;55W9,SECC,T1.0,BLK 1 23 CABINET BACK-TOP;55W3,PS SHEET,T4.0 1 24 CABINET BACK-BOT;55W3,HIPS HB,BLK 1 25 ASSY CHASSIS;SP55W3HFX/BWT 1 Remark Samsung Electronics Electrical Parts List 7. Electrical Parts List 7-1 SP47W3HFX/BOB Level Loc. No. Code No. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 AA59-00220A AA94-03599A AA94-03600A AA94-03601A 0203-001329 AA02-00022A 6005-001004 6001-000137 6003-001019 6003-001026 6005-001003 6005-001005 6006-001094 AA60-00132A AA60-10011A AA61-00617B AA61-00859A AA91-00921A AA91-00921B AA61-00972B AA61-00049B AA73-00005B AA63-10007C AA63-60131A AA63-70002A AA64-01395Q AA64-02336A AA64-02074D AA64-02224B AA64-02225B AA64-60449B AA65-30008A AA67-00196A AA67-00119B AA67-00136A AA67-00165A AA69-00744L AA69-01227B AA69-01298A AA69-01299E AA73-00008A AA91-00773A AA91-03555A AA94-11168D AA95-01841C AA95-01790K AA95-01847G AA95-01785E AA94-11166E AA95-01753D AA96-20130A 0201-001059 AA26-00101A AA39-20577B AA40-00094A AA40-00095A AA59-00171A AA63-10002A AA65-30013A AA65-30018A AA65-30104B AA68-02302A AA68-50509A AA68-00344A AA68-00341A AC68-00347A AA68-00340A AA68-00345A Samsung Electronics Description ; Specification Remark REMOCON;,TM63,SHARK,51,L/GRAY,EAST ASI ASSY CRT-(R);P16LSG03RJA,+380MG,7,PCL621 ASSY CRT-(G);P16LSG03HKA,+380MG,7,PCL621 ASSY CRT-(B);P16LSG03BMB,+380MG,7,PCL621 TAPE-OPP MASKING;ANT-300P,T0.07,W15.0,L5 TAPE ETC;SESA,T0.3,75,132,BLK SCREW-WOOD;HH,+,M4,L27,BLK,SWRCH18A SCREW-MACHINE;BH,+,M3,L8,ZPC(YEL),SM20C, SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK) SCREW-WOOD;HH,+,M4,L19,ZPC(BLK),SWRCH18A SCREW-WOOD;HH,+,M4.0,L19,NI PLT,SWRCH18A SCREW-ASS’Y WOOD;WW,HH,+,M7,L32,ZPC(YEL) SPACER-COVER,DUST;DP,W3,T0.5,60-00123B SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, BRACKET-CRT,MAIN;DP,54J7,AA61-00475B PLATE-CENTER,SPK;W3,WOOD ASSY-HOLDER,MIRROR;,HIPS HB BLK,47W3 ASSY-HOLDER,MIRROR;,HIPS HB BLK,47W3 HOLDER-SCREEN,R;47H1,ABS HB,GRAY HOLDER-BOX;-,PP,-,-,-,NTR,V0,AA61-20285A RUBBER-CAP;FLAT,PRJ,SILICONE RUBBER,WHIT BAND-PP;-,-,-,W18,-,CLEAR,1G SPACER-FELT;SVP403J,FELT,-,-,-,BLK,T0.5, SHEET;-,PE FOAM,T1.0,-,-,-,50G INLAY-TERMINAL;47W3,PS SHEET,T0.5,BLK,J5 CABINET-BACK,BOT;W3,HIPS,V0,BLK INLAY-SPEAKER;T6,W3,PS SHEET,T0.5,J52A P CABINET-BACK,TOP;DP,47W3,HIPS HB,BLK,64CABINET-BACK,SIDE;DP,47.55W3,HIPS HB,BLK INLAY-COVER;SP-434JMF,PS,T0.5,149.3X69.5 CLAMP-CORD;-,PE,HB,-,BLK,AA95-00714B70*612,T=0.73,P=0.52 SCREEN-FRESNEL;47W,-,T2,1072*6 SUN SCREEN-AG;47W,-,T=82%,1072*614*2,-,MIRROR-FRONT;47W3,GLASS ,861*677*421,FS BAG-SHEET;-,HDPE PE FOAM,T0.015,W1650,H1 CUSHION SET;47W3,EPS C=0.02 PACKING CASE-IN;47W3,CB H-3 AB,YEL,1207 PACKING CASE-OUT;47W3,CB H-3 AB,YEL,SESA RUBBER-SHEET;47W3,MBR,18*50,T2.0 ASSY-BRACKER,MIRROR;DP,91-00751A 19.5KG, ASSY CHASSIS;SP47W3HFS/XEF ASSY PCB MISC-V/M;DP,PCL545R,P54A ASSY SUB-PCB,SENSOR;DP,PCL545R,P54A,AA95 ASSY SUB-PCB,A/V TERMINAL;DP,SP55W3HF,J5 ASSY SUB-PCB,SUB AMP;DP,SP55W3HF,J52AAA9 ASSY SUB-PCB,A/V FRONT;DP,SP55W3HF,J52A3 ASSY PCB MISC-CRT;DP,SP47W3HF,J52A ASSY SUB-PCB CONTROL;DP,SP47W3HF,J52A,AA ASSY-POWER,CORD;-,CP2/NO(4.0R),H/C150,KJ ADHESIVE-SIL;#9590,WHT,-,CARTRIGE TRANS FBT;FWZ50A001E/FFA97513B,12KV,5P,LEAD CONNECTOR ASSY;P54A/SVP-55W3HD,UL16 TUNER;TCLW3101PD16A(S),PAL/SECAM,181 TUNER;TCPW3001PC16A(S),PAL/SECAM,181 MODULE-FOCUS,PACK;SVP-5200,S300-P3,-,-,BAND-TIE;-,NYLON66 V2,-,-,L100,NTR,CLAMP-WIRE;-,NYLON-6 CLAMP-WIRE;DONG-A,NYLON-66,-,-,-,DATL-60 CLAMP-WIRE;ALL MODEL,NYLON 66,V2,-,BLK,W MANUAL USERS;W3/T6,BULGARIA,W/P100(G),1, LABEL-BOX;A/P 90(G),ALL MODEL,-,WHT,L250 LABEL-TRANSFER BOX;-,TF-53B LABEL-RATING;-,TF53B5DF,-,SILVER,5 LABEL-TRANSFER RATING;ALTA RESISTENCI LABEL-WARRANTY;-,-,-,WHT,75MM,20 LABEL-TRANSFER WARRANTY;-,TF-53B5D Level Loc. No. Code No. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 AA61-20126A AA69-30009C 4301-000115 AA39-40001B AA69-00862A AA68-50523A AA39-30007B 0203-000402 6003-001023 6003-001022 AA68-02155A AA68-02156A AA68-02415A BP65-00001A AA69-01874A Description ; Specification Remark HOLDER-LEG;-,ABS,-,-,-,BLK, BAG-SHEET;LDPE,T0.08,W150,L120,-,-,BATTERY-ALKALINE;1.5V,750mAH,AAA,10. CABLE-RCA;,1500MM BAG PE;-,HDPE PE FOAM,T0.03,W400,H240 LABEL-BACK,DOLBY;A/P 100(G),CW764AHD,DOL IF-CABLE;-,T,150mm,1365#26 TAPE-KRAFT;KRAFT,T0.17,W18,L50,BLK SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW SCREW-TAPTITE;RH,+,B,M3,L12,ZPC(BLK),SWR LABEL-POP,RACK;W3 ,PASCAL, ,REMOVABLE LABEL-POP,AGS;W3 ,PASCAL, ,REMOVABLE CARD-RTF;COLORIT 54 CREMA,MOJO80G,SPA,A TERMINAL-BOARD,ANT;,DP,42W5,AA65-00021A PALLET;ALL MODEL,WOOD,800,1250,120 ASSY-C/FRONT,BOT 1 AA91-00775H ASSY-C/FRONT,BOT;DP,64-02063P,47W3 2 2 2 2 2 2 2 2 2 2 2 2 AA64-02063C AA61-00791B AA61-01068A AA64-02205B BP96-00127A 6003-001026 AA61-00785B AA61-00786B AA61-60003J AA64-02080B AA64-02081B AA64-02082B CABINET-FRONT,BOT;47W3,,HIPS HB,GRAY,SV8 HOLDER-FRONT,BOT;W3,ABS HB,L40,BLK,D HOLDER-CABINET,BOT(B);W3,ABS HB,L40,BLK, BADGE-DECORATION;W3,NI+AL FORGING+NI,RS ASSY COVER P-HOLDER,CONTROL;DP,W3,ABS HB SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK) GUIDE-KNOB,POWER;W3,ABS HB ,BLK,C HOLDER-CONTROL;W3,ABS HB,WHT,SV104M SPRING-CS;-,SUS304,-,-,OD6, KNOB POWER;W3,ABS HB WHT,SV104M KNOB-CH,VOL;W3,ABS HB,BLK,CH WINDOW-RMC,LED;W3,PC,CLEAR ASSY-DOOR,RACK 1 AA91-00774E ASSY-DOOR,RACK;DP,W3,HB GRAY,64-02066 2 2 2 2 2 2 2 2 AA64-02066C AA64-02206B AA91-00758A AA91-00749A BP61-00128A AA61-00782B AA73-00007B 6003-001019 DOOR-RACK;47.55.65W3,HIPS HB,GRAY,SV808 WINDOW-DOOR;W3,GLASS,T3.0,BR ASSY-HINGE,DOOR(R);SPRING,SECC T1.6 W3,W ASSY-HINGE,DOOR(L);,NO-SPRING SECC T1.6, BRACKET-DOOR;DP,47W3,AA61-00856B BRACKET-MAGNET;W3,SPC,T2.0,FZW RUBBER-CAP;W3,MBR,GRAY,60 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR ASSY-C/FRONT,MASK 1 AA91-00824D ASSY-C/FRONT,MASK;DP,HB GRAY,02058C 22K 2 2 2 2 AA64-02058C AA64-02211B AA63-00063A AA61-00974A CABINET-FRONT,MASK;47W3,HIPS HB,GRAY,SVM BADGE-BRAND;72MM,AL FORGING,SVM1-126PS,S SPACER-DUAL,LOCK;#400,-,-,19X19,SVP-614J HOLDER-MASK;47H1,HIPS HB,BLK ASSY-CABINET,WOOD 1 AA90-00970A ASSY-CABINET,WOOD;SP47W3HFS/XEF,47W3 2 2 AA91-00759E ASSY-CABINET,WOOD;,WOOD XSA,47W3 AA64-02207A CABINET-WOOD;47W3,WOOD 7-1 Electrical Parts List Level Loc. No. Code No. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 2 2 2 2 2 2 2 7-2 AA60-00078B AA60-10051A AA60-10051B AA61-00094C AA61-00097A AA61-00723A AA61-00507B BP61-00075A AA61-00616B AA61-01117A AA61-00864A AA61-00894B AA61-00894A AA61-00458B AA61-00865A BP61-00087A BP61-00087B AA61-00857B AA61-00858B AA61-10247A AA63-00348B AA65-00014C AA91-00750A AA96-00753A 3001-000151 3001-001107 3001-001134 AA39-00086A AA39-00287A AA39-20609A AA98-00049B 6005-001006 AA60-10050Y AA61-00999A AA61-20219A AA61-01070A AA61-00975A BP63-00001A Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark SPACER-DUAL,LOCK;W3,#250,19*40 SCREW-WOOD;-,SWRCH18A,M4,L16,PH,+,-,-,ZP SCREW-WOOD;-,SWRCH18A,M3.5,L11,RH,+,-,-, HOLDER-RAIL;PCJ533R,ABS,-,-,-,BLK,HB,480 HOLDER-WIRE;-,NYLON 6/6,-,-,-,NTR,HOLDER-PIN,DABO;PRJT,WOODEN NAIL,OD6XL20 HOLDER-CABINET,WOOD;43,54,62J8,ABS,-,-,HOLDER-JERSEY,ASSY;W3,ABS V0,GRAY,63-000 HOLDER-CRT,MAIN;54J7,DP,-,-,-,-,AA61-005 HOLDER-SENSOR,SIDE;W3,ABS HB,G3676,SIDE HOLDER-PCB;W3,HIPS,V0,BLK HOLDER-SCREEN,TOP;W3,DP,L1082,BLK,61-008 HOLDER-SCREEN,TOP;W3,DP,L1102,BLK,61-008 CASTER;-,TP4020-05 PLY,-,OH56,-,-,SR4 HOLDER-SCREEN,RL;W3,DP,61-00788B 16.2KG RAIL-DOOR,R;W3,ABS HB,BLK RAIL-DOOR,L;W3,ABS HB,BLK BRACKET-NUT,INSERT;W3,M3 ZN BRACKET-FRAME;W3,SECC,T2.0 BRACKET-FOCUS;S46DS,SECC,T1.0,-,-,-,COVER-DUCT;54,62J8,HIPS,-,HB,BLK,-,CLAMP-WIRE;54J9,SINGLE NYLON,-,-,BLK,ASSY-MAGNET,PUSH;,MAGNET,W3 ASSY SPEAKER;,3001-001107) SPEAKER;20W,8ohm,92dB,130Hz SPEAKER;20W,8ohm,95dB,1300Hz SPEAKER;30W,8ohm,93dB,60Hz LEAD CONNECTOR-ASSY;,2.2UF,REC,REC,200MM LEAD CONNECTOR ASSY;PCL54RX,UL2547#26,UL LEAD CONNECTOR-ASSY;,2P,SMH250-02,REC,40 ASSY-LEAD,CON;-,LEAD-CON,CORE,AA39-20505 SCREW-WOOD;FH,+,M3,L15.0,ZPC(BLK),SWRCH1 SCREW-WOOD;-,SWRCH18A,M4,L40,FH,+,-,-,ZP HOLDER-DUAL,LOCK;W3,W1,ABS HB,BLK HOLDER-FRONT,BOT,E;,ABS,HB,L40,BLK HOLDER-CABINET,BOT(D);W3,ABS HB,L990,BLK HOLDER-CABINET,BOT-F;W3,ABS HB,GRAY SHEET-EMI;55W3,PS V2+AL LAMI,T0.35,350* Samsung Electronics Electrical Parts List 7-2 SP47W3HFX/COM Level Loc. No. Code No. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 AA59-00220A AA94-03599A AA94-03600A AA94-03601A 0203-001329 AA02-00022A 6005-001004 6001-000137 6003-001019 6003-001026 6005-001003 6005-001005 6006-001094 AA60-00132A AA60-10011A AA61-00617B AA61-00859A AA91-00921A AA91-00921B AA61-00972B AA61-00049B AA73-00005B AA63-10007C AA63-60131A AA63-70002A AA64-01395Q AA64-02336A AA64-02074D AA64-02224B AA64-02225B AA64-60449B AA65-30008A AA67-00196A AA67-00119B AA67-00136A AA67-00165A AA69-00744L AA69-01227B AA69-01298A AA69-01299E AA73-00008A AA91-00773A AA91-03555A AA94-11168D AA95-01841C AA95-01790K AA95-01847G AA95-01785E AA94-11166E AA95-01753D AA96-20130A 0201-001059 AA26-00101A AA39-20577B AA40-00094A AA40-00095A AA59-00171A AA63-10002A AA65-30013A AA65-30018A AA65-30104B AA68-50509A AA68-00344A AA68-00341A AC68-00347A AA68-00340A AA68-00345A AA61-20126A AA68-01780A AA69-30009C 4301-000115 AA39-40001B AA69-00862A Samsung Electronics Description ; Specification Remark REMOCON;,TM63,SHARK,51,L/GRAY,EAST ASI ASSY CRT-(R);P16LSG03RJA,+380MG,7,PCL621 ASSY CRT-(G);P16LSG03HKA,+380MG,7,PCL621 ASSY CRT-(B);P16LSG03BMB,+380MG,7,PCL621 TAPE-OPP MASKING;ANT-300P,T0.07,W15.0,L5 TAPE ETC;SESA,T0.3,75,132,BLK SCREW-WOOD;HH,+,M4,L27,BLK,SWRCH18A SCREW-MACHINE;BH,+,M3,L8,ZPC(YEL),SM20C, SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK) SCREW-WOOD;HH,+,M4,L19,ZPC(BLK),SWRCH18A SCREW-WOOD;HH,+,M4.0,L19,NI PLT,SWRCH18A SCREW-ASS’Y WOOD;WW,HH,+,M7,L32,ZPC(YEL) SPACER-COVER,DUST;DP,W3,T0.5,60-00123B SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, BRACKET-CRT,MAIN;DP,54J7,AA61-00475B PLATE-CENTER,SPK;W3,WOOD ASSY-HOLDER,MIRROR;,HIPS HB BLK,47W3 ASSY-HOLDER,MIRROR;,HIPS HB BLK,47W3 HOLDER-SCREEN,R;47H1,ABS HB,GRAY HOLDER-BOX;-,PP,-,-,-,NTR,V0,AA61-20285A RUBBER-CAP;FLAT,PRJ,SILICONE RUBBER,WHIT BAND-PP;-,-,-,W18,-,CLEAR,1G SPACER-FELT;SVP403J,FELT,-,-,-,BLK,T0.5, SHEET;-,PE FOAM,T1.0,-,-,-,50G INLAY-TERMINAL;47W3,PS SHEET,T0.5,BLK,J5 CABINET-BACK,BOT;W3,HIPS,V0,BLK INLAY-SPEAKER;T6,W3,PS SHEET,T0.5,J52A P CABINET-BACK,TOP;DP,47W3,HIPS HB,BLK,64CABINET-BACK,SIDE;DP,47.55W3,HIPS HB,BLK INLAY-COVER;SP-434JMF,PS,T0.5,149.3X69.5 CLAMP-CORD;-,PE,HB,-,BLK,AA95-00714B70*612,T=0.73,P=0.52 SCREEN-FRESNEL;47W,-,T2,1072*6 SUN SCREEN-AG;47W,-,T=82%,1072*614*2,-,MIRROR-FRONT;47W3,GLASS ,861*677*421,FS BAG-SHEET;-,HDPE PE FOAM,T0.015,W1650,H1 CUSHION SET;47W3,EPS C=0.02 PACKING CASE-IN;47W3,CB H-3 AB,YEL,1207 PACKING CASE-OUT;47W3,CB H-3 AB,YEL,SESA RUBBER-SHEET;47W3,MBR,18*50,T2.0 ASSY-BRACKER,MIRROR;DP,91-00751A 19.5KG, ASSY CHASSIS;SP47W3HFS/XEF ASSY PCB MISC-V/M;DP,PCL545R,P54A ASSY SUB-PCB,SENSOR;DP,PCL545R,P54A,AA95 ASSY SUB-PCB,A/V TERMINAL;DP,SP55W3HF,J5 ASSY SUB-PCB,SUB AMP;DP,SP55W3HF,J52AAA9 ASSY SUB-PCB,A/V FRONT;DP,SP55W3HF,J52A3 ASSY PCB MISC-CRT;DP,SP47W3HF,J52A ASSY SUB-PCB CONTROL;DP,SP47W3HF,J52A,AA ASSY-POWER,CORD;-,CP2/NO(4.0R),H/C150,KJ ADHESIVE-SIL;#9590,WHT,-,CARTRIGE TRANS FBT;FWZ50A001E/FFA97513B,12KV,5P,LEAD CONNECTOR ASSY;P54A/SVP-55W3HD,UL16 TUNER;TCLW3101PD16A(S),PAL/SECAM,181 TUNER;TCPW3001PC16A(S),PAL/SECAM,181 MODULE-FOCUS,PACK;SVP-5200,S300-P3,-,-,BAND-TIE;-,NYLON66 V2,-,-,L100,NTR,CLAMP-WIRE;-,NYLON-6 CLAMP-WIRE;DONG-A,NYLON-66,-,-,-,DATL-60 CLAMP-WIRE;ALL MODEL,NYLON 66,V2,-,BLK,W LABEL-BOX;A/P 90(G),ALL MODEL,-,WHT,L250 LABEL-TRANSFER BOX;-,TF-53B LABEL-RATING;-,TF53B5DF,-,SILVER,5 LABEL-TRANSFER RATING;ALTA RESISTENCI LABEL-WARRANTY;-,-,-,WHT,75MM,20 LABEL-TRANSFER WARRANTY;-,TF-53B5D HOLDER-LEG;-,ABS,-,-,-,BLK, MANUAL USERS;W3,GER,W/P100(G),1,B5,J52A, BAG-SHEET;LDPE,T0.08,W150,L120,-,-,BATTERY-ALKALINE;1.5V,750mAH,AAA,10. CABLE-RCA;,1500MM BAG PE;-,HDPE PE FOAM,T0.03,W400,H240 Level Loc. No. Code No. 1 1 1 1 1 1 1 1 1 1 1 AA68-50523A AA39-30007B 0203-000402 6003-001023 6003-001022 AA68-02155A AA68-02156A 6801-001015 AA68-02415A BP65-00001A AA69-01874A Description ; Specification Remark LABEL-BACK,DOLBY;A/P 100(G),CW764AHD,DOL IF-CABLE;-,T,150mm,1365#26 TAPE-KRAFT;KRAFT,T0.17,W18,L50,BLK SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW SCREW-TAPTITE;RH,+,B,M3,L12,ZPC(BLK),SWR LABEL-POP,RACK;W3 ,PASCAL, ,REMOVABLE LABEL-POP,AGS;W3 ,PASCAL, ,REMOVABLE CARD REGISTRATION;XEG,GERMAN,MOJO100 CARD-RTF;COLORIT 54 CREMA,MOJO80G,SPA,A TERMINAL-BOARD,ANT;,DP,42W5,AA65-00021A PALLET;ALL MODEL,WOOD,800,1250,120 ASSY-C/FRONT,BOT 1 AA91-00775H ASSY-C/FRONT,BOT;DP,64-02063P,47W3 2 2 2 2 2 2 2 2 2 2 2 2 AA64-02063C AA61-00791B AA61-01068A AA64-02205B BP96-00127A 6003-001026 AA61-00785B AA61-00786B AA61-60003J AA64-02080B AA64-02081B AA64-02082B CABINET-FRONT,BOT;47W3,,HIPS HB,GRAY,SV8 HOLDER-FRONT,BOT;W3,ABS HB,L40,BLK,D HOLDER-CABINET,BOT(B);W3,ABS HB,L40,BLK, BADGE-DECORATION;W3,NI+AL FORGING+NI,RS ASSY COVER P-HOLDER,CONTROL;DP,W3,ABS HB SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK) GUIDE-KNOB,POWER;W3,ABS HB ,BLK,C HOLDER-CONTROL;W3,ABS HB,WHT,SV104M SPRING-CS;-,SUS304,-,-,OD6, KNOB POWER;W3,ABS HB WHT,SV104M KNOB-CH,VOL;W3,ABS HB,BLK,CH WINDOW-RMC,LED;W3,PC,CLEAR ASSY-DOOR,RACK 1 AA91-00774E ASSY-DOOR,RACK;DP,W3,HB GRAY,64-02066 2 2 2 2 2 2 2 2 AA64-02066C AA64-02206B AA91-00758A AA91-00749A BP61-00128A AA61-00782B AA73-00007B 6003-001019 DOOR-RACK;47.55.65W3,HIPS HB,GRAY,SV808 WINDOW-DOOR;W3,GLASS,T3.0,BR ASSY-HINGE,DOOR(R);SPRING,SECC T1.6 W3,W ASSY-HINGE,DOOR(L);,NO-SPRING SECC T1.6, BRACKET-DOOR;DP,47W3,AA61-00856B BRACKET-MAGNET;W3,SPC,T2.0,FZW RUBBER-CAP;W3,MBR,GRAY,60 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR ASSY-C/FRONT,MASK 1 AA91-00824D ASSY-C/FRONT,MASK;DP,HB GRAY,02058C 22K 2 2 2 2 AA64-02058C AA64-02211B AA63-00063A AA61-00974A CABINET-FRONT,MASK;47W3,HIPS HB,GRAY,SVM BADGE-BRAND;72MM,AL FORGING,SVM1-126PS,S SPACER-DUAL,LOCK;#400,-,-,19X19,SVP-614J HOLDER-MASK;47H1,HIPS HB,BLK ASSY-CABINET,WOOD 1 AA90-00970A ASSY-CABINET,WOOD;SP47W3HFS/XEF,47W3 2 2 2 2 2 2 2 2 2 2 2 AA91-00759E AA64-02207A AA60-00078B AA60-10051A AA60-10051B AA61-00094C AA61-00097A AA61-00723A AA61-00507B BP61-00075A AA61-00616B ASSY-CABINET,WOOD;,WOOD XSA,47W3 CABINET-WOOD;47W3,WOOD SPACER-DUAL,LOCK;W3,#250,19*40 SCREW-WOOD;-,SWRCH18A,M4,L16,PH,+,-,-,ZP SCREW-WOOD;-,SWRCH18A,M3.5,L11,RH,+,-,-, HOLDER-RAIL;PCJ533R,ABS,-,-,-,BLK,HB,480 HOLDER-WIRE;-,NYLON 6/6,-,-,-,NTR,HOLDER-PIN,DABO;PRJT,WOODEN NAIL,OD6XL20 HOLDER-CABINET,WOOD;43,54,62J8,ABS,-,-,HOLDER-JERSEY,ASSY;W3,ABS V0,GRAY,63-000 HOLDER-CRT,MAIN;54J7,DP,-,-,-,-,AA61-005 7-3 Electrical Parts List Level Loc. No. Code No. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 2 2 2 2 2 2 2 7-4 AA61-01117A AA61-00864A AA61-00894B AA61-00894A AA61-00458B AA61-00865A BP61-00087A BP61-00087B AA61-00857B AA61-00858B AA61-10247A AA63-00348B AA65-00014C AA91-00750A AA96-00753A 3001-000151 3001-001107 3001-001134 AA39-00086A AA39-00287A AA39-20609A AA98-00049B 6005-001006 AA60-10050Y AA61-00999A AA61-20219A AA61-01070A AA61-00975A BP63-00001A Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark HOLDER-SENSOR,SIDE;W3,ABS HB,G3676,SIDE HOLDER-PCB;W3,HIPS,V0,BLK HOLDER-SCREEN,TOP;W3,DP,L1082,BLK,61-008 HOLDER-SCREEN,TOP;W3,DP,L1102,BLK,61-008 CASTER;-,TP4020-05 PLY,-,OH56,-,-,SR4 HOLDER-SCREEN,RL;W3,DP,61-00788B 16.2KG RAIL-DOOR,R;W3,ABS HB,BLK RAIL-DOOR,L;W3,ABS HB,BLK BRACKET-NUT,INSERT;W3,M3 ZN BRACKET-FRAME;W3,SECC,T2.0 BRACKET-FOCUS;S46DS,SECC,T1.0,-,-,-,COVER-DUCT;54,62J8,HIPS,-,HB,BLK,-,CLAMP-WIRE;54J9,SINGLE NYLON,-,-,BLK,ASSY-MAGNET,PUSH;,MAGNET,W3 ASSY SPEAKER;,3001-001107) SPEAKER;20W,8ohm,92dB,130Hz SPEAKER;20W,8ohm,95dB,1300Hz SPEAKER;30W,8ohm,93dB,60Hz LEAD CONNECTOR-ASSY;,2.2UF,REC,REC,200MM LEAD CONNECTOR ASSY;PCL54RX,UL2547#26,UL LEAD CONNECTOR-ASSY;,2P,SMH250-02,REC,40 ASSY-LEAD,CON;-,LEAD-CON,CORE,AA39-20505 SCREW-WOOD;FH,+,M3,L15.0,ZPC(BLK),SWRCH1 SCREW-WOOD;-,SWRCH18A,M4,L40,FH,+,-,-,ZP HOLDER-DUAL,LOCK;W3,W1,ABS HB,BLK HOLDER-FRONT,BOT,E;,ABS,HB,L40,BLK HOLDER-CABINET,BOT(D);W3,ABS HB,L990,BLK HOLDER-CABINET,BOT-F;W3,ABS HB,GRAY SHEET-EMI;55W3,PS V2+AL LAMI,T0.35,350* Samsung Electronics Electrical Parts List 7-3 SP47W3HFX/EUE Level Loc. No. Code No. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 AA59-00220A AA94-03599A AA94-03600A AA94-03601A 0203-001329 AA02-00022A 6005-001004 6001-000137 6003-001019 6003-001026 6005-001003 6005-001005 6006-001094 AA60-00132A AA60-10011A AA61-00617B AA61-00859A AA91-00921A AA91-00921B AA61-00972B AA61-00049B AA73-00005B AA63-10007C AA63-60131A AA63-70002A AA64-01395Q AA64-02336A AA64-02074D AA64-02224B AA64-02225B AA64-60449B AA65-30008A AA67-00196A AA67-00119B AA67-00136A AA67-00165A AA69-00744L AA69-01227B AA69-01298A AA69-01299E AA73-00008A AA91-00773A AA91-03555A AA94-11168D AA95-01841C AA95-01790K AA95-01847G AA95-01785E AA94-11166E AA95-01753D AA96-20130A 0201-001059 AA26-00101A AA39-20577B AA40-00094A AA40-00095A AA59-00171A AA63-10002A AA65-30013A AA65-30018A AA65-30104B AA68-50509A AA68-00344A AA68-00341A AC68-00347A AA68-00340A AA68-00345A AA61-20126A AA68-01778A AA69-30009C 4301-000115 AA39-40001B AA69-00862A Samsung Electronics Description ; Specification Remark REMOCON;,TM63,SHARK,51,L/GRAY,EAST ASI ASSY CRT-(R);P16LSG03RJA,+380MG,7,PCL621 ASSY CRT-(G);P16LSG03HKA,+380MG,7,PCL621 ASSY CRT-(B);P16LSG03BMB,+380MG,7,PCL621 TAPE-OPP MASKING;ANT-300P,T0.07,W15.0,L5 TAPE ETC;SESA,T0.3,75,132,BLK SCREW-WOOD;HH,+,M4,L27,BLK,SWRCH18A SCREW-MACHINE;BH,+,M3,L8,ZPC(YEL),SM20C, SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK) SCREW-WOOD;HH,+,M4,L19,ZPC(BLK),SWRCH18A SCREW-WOOD;HH,+,M4.0,L19,NI PLT,SWRCH18A SCREW-ASS’Y WOOD;WW,HH,+,M7,L32,ZPC(YEL) SPACER-COVER,DUST;DP,W3,T0.5,60-00123B SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, BRACKET-CRT,MAIN;DP,54J7,AA61-00475B PLATE-CENTER,SPK;W3,WOOD ASSY-HOLDER,MIRROR;,HIPS HB BLK,47W3 ASSY-HOLDER,MIRROR;,HIPS HB BLK,47W3 HOLDER-SCREEN,R;47H1,ABS HB,GRAY HOLDER-BOX;-,PP,-,-,-,NTR,V0,AA61-20285A RUBBER-CAP;FLAT,PRJ,SILICONE RUBBER,WHIT BAND-PP;-,-,-,W18,-,CLEAR,1G SPACER-FELT;SVP403J,FELT,-,-,-,BLK,T0.5, SHEET;-,PE FOAM,T1.0,-,-,-,50G INLAY-TERMINAL;47W3,PS SHEET,T0.5,BLK,J5 CABINET-BACK,BOT;W3,HIPS,V0,BLK INLAY-SPEAKER;T6,W3,PS SHEET,T0.5,J52A P CABINET-BACK,TOP;DP,47W3,HIPS HB,BLK,64CABINET-BACK,SIDE;DP,47.55W3,HIPS HB,BLK INLAY-COVER;SP-434JMF,PS,T0.5,149.3X69.5 CLAMP-CORD;-,PE,HB,-,BLK,AA95-00714B70*612,T=0.73,P=0.52 SCREEN-FRESNEL;47W,-,T2,1072*6 SUN SCREEN-AG;47W,-,T=82%,1072*614*2,-,MIRROR-FRONT;47W3,GLASS ,861*677*421,FS BAG-SHEET;-,HDPE PE FOAM,T0.015,W1650,H1 CUSHION SET;47W3,EPS C=0.02 PACKING CASE-IN;47W3,CB H-3 AB,YEL,1207 PACKING CASE-OUT;47W3,CB H-3 AB,YEL,SESA RUBBER-SHEET;47W3,MBR,18*50,T2.0 ASSY-BRACKER,MIRROR;DP,91-00751A 19.5KG, ASSY CHASSIS;SP47W3HFS/XEF ASSY PCB MISC-V/M;DP,PCL545R,P54A ASSY SUB-PCB,SENSOR;DP,PCL545R,P54A,AA95 ASSY SUB-PCB,A/V TERMINAL;DP,SP55W3HF,J5 ASSY SUB-PCB,SUB AMP;DP,SP55W3HF,J52AAA9 ASSY SUB-PCB,A/V FRONT;DP,SP55W3HF,J52A3 ASSY PCB MISC-CRT;DP,SP47W3HF,J52A ASSY SUB-PCB CONTROL;DP,SP47W3HF,J52A,AA ASSY-POWER,CORD;-,CP2/NO(4.0R),H/C150,KJ ADHESIVE-SIL;#9590,WHT,-,CARTRIGE TRANS FBT;FWZ50A001E/FFA97513B,12KV,5P,LEAD CONNECTOR ASSY;P54A/SVP-55W3HD,UL16 TUNER;TCLW3101PD16A(S),PAL/SECAM,181 TUNER;TCPW3001PC16A(S),PAL/SECAM,181 MODULE-FOCUS,PACK;SVP-5200,S300-P3,-,-,BAND-TIE;-,NYLON66 V2,-,-,L100,NTR,CLAMP-WIRE;-,NYLON-6 CLAMP-WIRE;DONG-A,NYLON-66,-,-,-,DATL-60 CLAMP-WIRE;ALL MODEL,NYLON 66,V2,-,BLK,W LABEL-BOX;A/P 90(G),ALL MODEL,-,WHT,L250 LABEL-TRANSFER BOX;-,TF-53B LABEL-RATING;-,TF53B5DF,-,SILVER,5 LABEL-TRANSFER RATING;ALTA RESISTENCI LABEL-WARRANTY;-,-,-,WHT,75MM,20 LABEL-TRANSFER WARRANTY;-,TF-53B5D HOLDER-LEG;-,ABS,-,-,-,BLK, I/B PJTV (RPM 995) BAG-SHEET;LDPE,T0.08,W150,L120,-,-,BATTERY-ALKALINE;1.5V,750mAH,AAA,10. CABLE-RCA;,1500MM BAG PE;-,HDPE PE FOAM,T0.03,W400,H240 Level Loc. No. Code No. 1 1 1 1 1 1 1 1 1 1 Description ; Specification AA68-50523A AA39-30007B 0203-000402 6003-001023 6003-001022 AA68-02155A AA68-02156A AA68-02415A BP65-00001A AA69-01874A Remark LABEL-BACK,DOLBY;A/P 100(G),CW764AHD,DOL IF-CABLE;-,T,150mm,1365#26 TAPE-KRAFT;KRAFT,T0.17,W18,L50,BLK SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW SCREW-TAPTITE;RH,+,B,M3,L12,ZPC(BLK),SWR LABEL-POP,RACK;W3 ,PASCAL, ,REMOVABLE LABEL-POP,AGS;W3 ,PASCAL, ,REMOVABLE CARD-RTF;COLORIT 54 CREMA,MOJO80G,SPA,A TERMINAL-BOARD,ANT;,DP,42W5,AA65-00021A PALLET;ALL MODEL,WOOD,800,1250,120 ASSY-C/FRONT,BOT 1 AA91-00775H ASSY-C/FRONT,BOT;DP,64-02063P,47W3 2 2 2 2 2 2 2 2 2 2 2 2 AA64-02063C AA61-00791B AA61-01068A AA64-02205B BP96-00127A 6003-001026 AA61-00785B AA61-00786B AA61-60003J AA64-02080B AA64-02081B AA64-02082B CABINET-FRONT,BOT;47W3,,HIPS HB,GRAY,SV8 HOLDER-FRONT,BOT;W3,ABS HB,L40,BLK,D HOLDER-CABINET,BOT(B);W3,ABS HB,L40,BLK, BADGE-DECORATION;W3,NI+AL FORGING+NI,RS ASSY COVER P-HOLDER,CONTROL;DP,W3,ABS HB SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK) GUIDE-KNOB,POWER;W3,ABS HB ,BLK,C HOLDER-CONTROL;W3,ABS HB,WHT,SV104M SPRING-CS;-,SUS304,-,-,OD6, KNOB POWER;W3,ABS HB WHT,SV104M KNOB-CH,VOL;W3,ABS HB,BLK,CH WINDOW-RMC,LED;W3,PC,CLEAR ASSY-DOOR,RACK 1 AA91-00774E ASSY-DOOR,RACK;DP,W3,HB GRAY,64-02066 2 2 2 2 2 2 2 2 AA64-02066C AA64-02206B AA91-00758A AA91-00749A BP61-00128A AA61-00782B AA73-00007B 6003-001019 DOOR-RACK;47.55.65W3,HIPS HB,GRAY,SV808 WINDOW-DOOR;W3,GLASS,T3.0,BR ASSY-HINGE,DOOR(R);SPRING,SECC T1.6 W3,W ASSY-HINGE,DOOR(L);,NO-SPRING SECC T1.6, BRACKET-DOOR;DP,47W3,AA61-00856B BRACKET-MAGNET;W3,SPC,T2.0,FZW RUBBER-CAP;W3,MBR,GRAY,60 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR ASSY-C/FRONT,MASK 1 AA91-00824D ASSY-C/FRONT,MASK;DP,HB GRAY,02058C 22K 2 2 2 2 AA64-02058C AA64-02211B AA63-00063A AA61-00974A CABINET-FRONT,MASK;47W3,HIPS HB,GRAY,SVM BADGE-BRAND;72MM,AL FORGING,SVM1-126PS,S SPACER-DUAL,LOCK;#400,-,-,19X19,SVP-614J HOLDER-MASK;47H1,HIPS HB,BLK ASSY-CABINET,WOOD 1 AA90-00970A ASSY-CABINET,WOOD;SP47W3HFS/XEF,47W3 2 2 2 2 2 2 2 2 2 2 2 AA91-00759E AA64-02207A AA60-00078B AA60-10051A AA60-10051B AA61-00094C AA61-00097A AA61-00723A AA61-00507B BP61-00075A AA61-00616B ASSY-CABINET,WOOD;,WOOD XSA,47W3 CABINET-WOOD;47W3,WOOD SPACER-DUAL,LOCK;W3,#250,19*40 SCREW-WOOD;-,SWRCH18A,M4,L16,PH,+,-,-,ZP SCREW-WOOD;-,SWRCH18A,M3.5,L11,RH,+,-,-, HOLDER-RAIL;PCJ533R,ABS,-,-,-,BLK,HB,480 HOLDER-WIRE;-,NYLON 6/6,-,-,-,NTR,HOLDER-PIN,DABO;PRJT,WOODEN NAIL,OD6XL20 HOLDER-CABINET,WOOD;43,54,62J8,ABS,-,-,HOLDER-JERSEY,ASSY;W3,ABS V0,GRAY,63-000 HOLDER-CRT,MAIN;54J7,DP,-,-,-,-,AA61-005 7-5 Electrical Parts List Level Loc. No. Code No. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 2 2 2 2 2 2 2 7-6 AA61-01117A AA61-00864A AA61-00894B AA61-00894A AA61-00458B AA61-00865A BP61-00087A BP61-00087B AA61-00857B AA61-00858B AA61-10247A AA63-00348B AA65-00014C AA91-00750A AA96-00753A 3001-000151 3001-001107 3001-001134 AA39-00086A AA39-00287A AA39-20609A AA98-00049B 6005-001006 AA60-10050Y AA61-00999A AA61-20219A AA61-01070A AA61-00975A BP63-00001A Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark HOLDER-SENSOR,SIDE;W3,ABS HB,G3676,SIDE HOLDER-PCB;W3,HIPS,V0,BLK HOLDER-SCREEN,TOP;W3,DP,L1082,BLK,61-008 HOLDER-SCREEN,TOP;W3,DP,L1102,BLK,61-008 CASTER;-,TP4020-05 PLY,-,OH56,-,-,SR4 HOLDER-SCREEN,RL;W3,DP,61-00788B 16.2KG RAIL-DOOR,R;W3,ABS HB,BLK RAIL-DOOR,L;W3,ABS HB,BLK BRACKET-NUT,INSERT;W3,M3 ZN BRACKET-FRAME;W3,SECC,T2.0 BRACKET-FOCUS;S46DS,SECC,T1.0,-,-,-,COVER-DUCT;54,62J8,HIPS,-,HB,BLK,-,CLAMP-WIRE;54J9,SINGLE NYLON,-,-,BLK,ASSY-MAGNET,PUSH;,MAGNET,W3 ASSY SPEAKER;,3001-001107) SPEAKER;20W,8ohm,92dB,130Hz SPEAKER;20W,8ohm,95dB,1300Hz SPEAKER;30W,8ohm,93dB,60Hz LEAD CONNECTOR-ASSY;,2.2UF,REC,REC,200MM LEAD CONNECTOR ASSY;PCL54RX,UL2547#26,UL LEAD CONNECTOR-ASSY;,2P,SMH250-02,REC,40 ASSY-LEAD,CON;-,LEAD-CON,CORE,AA39-20505 SCREW-WOOD;FH,+,M3,L15.0,ZPC(BLK),SWRCH1 SCREW-WOOD;-,SWRCH18A,M4,L40,FH,+,-,-,ZP HOLDER-DUAL,LOCK;W3,W1,ABS HB,BLK HOLDER-FRONT,BOT,E;,ABS,HB,L40,BLK HOLDER-CABINET,BOT(D);W3,ABS HB,L990,BLK HOLDER-CABINET,BOT-F;W3,ABS HB,GRAY SHEET-EMI;55W3,PS V2+AL LAMI,T0.35,350* Samsung Electronics Electrical Parts List 7-4 SP47W3HFX/XEH Level Loc. No. Code No. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Description ; Specification AA59-00220A AA94-03599A AA94-03600A AA94-03601A 0203-001329 AA02-00022A 6005-001004 6001-000137 6003-001019 6003-001026 6005-001003 6005-001005 6006-001094 AA60-00132A AA60-10011A AA61-00617B AA61-00859A AA91-00921A AA91-00921B AA61-00972B AA61-00049B AA73-00005B AA63-10007C AA63-60131A AA63-70002A AA64-01395Q AA64-02336A AA64-02074D AA64-02224B AA64-02225B AA64-60449B AA65-30008A AA67-00196A AA67-00119B AA67-00136A AA67-00165A AA69-00744L AA69-01227B AA69-01298A AA69-01299E AA73-00008A AA91-00773A AA91-03555A AA94-11168D AA95-01841C AA95-01790K AA95-01847G AA95-01785E AA94-11166E AA95-01753D AA96-20130A 0201-001059 AA26-00101A AA39-20577B AA40-00094A AA40-00095A AA59-00171A AA63-10002A AA65-30013A AA65-30018A AA65-30104B AA68-50509A AA68-00344A AA68-00341A AC68-00347A AA68-00340A AA68-00345A AA61-20126A AA69-30009C 4301-000115 AA39-40001B AA69-00862A AA68-50523A Samsung Electronics Remark REMOCON;,TM63,SHARK,51,L/GRAY,EAST ASI ASSY CRT-(R);P16LSG03RJA,+380MG,7,PCL621 ASSY CRT-(G);P16LSG03HKA,+380MG,7,PCL621 ASSY CRT-(B);P16LSG03BMB,+380MG,7,PCL621 TAPE-OPP MASKING;ANT-300P,T0.07,W15.0,L5 TAPE ETC;SESA,T0.3,75,132,BLK SCREW-WOOD;HH,+,M4,L27,BLK,SWRCH18A SCREW-MACHINE;BH,+,M3,L8,ZPC(YEL),SM20C, SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK) SCREW-WOOD;HH,+,M4,L19,ZPC(BLK),SWRCH18A SCREW-WOOD;HH,+,M4.0,L19,NI PLT,SWRCH18A SCREW-ASS’Y WOOD;WW,HH,+,M7,L32,ZPC(YEL) SPACER-COVER,DUST;DP,W3,T0.5,60-00123B SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, BRACKET-CRT,MAIN;DP,54J7,AA61-00475B PLATE-CENTER,SPK;W3,WOOD ASSY-HOLDER,MIRROR;,HIPS HB BLK,47W3 ASSY-HOLDER,MIRROR;,HIPS HB BLK,47W3 HOLDER-SCREEN,R;47H1,ABS HB,GRAY HOLDER-BOX;-,PP,-,-,-,NTR,V0,AA61-20285A RUBBER-CAP;FLAT,PRJ,SILICONE RUBBER,WHIT BAND-PP;-,-,-,W18,-,CLEAR,1G SPACER-FELT;SVP403J,FELT,-,-,-,BLK,T0.5, SHEET;-,PE FOAM,T1.0,-,-,-,50G INLAY-TERMINAL;47W3,PS SHEET,T0.5,BLK,J5 CABINET-BACK,BOT;W3,HIPS,V0,BLK INLAY-SPEAKER;T6,W3,PS SHEET,T0.5,J52A P CABINET-BACK,TOP;DP,47W3,HIPS HB,BLK,64CABINET-BACK,SIDE;DP,47.55W3,HIPS HB,BLK INLAY-COVER;SP-434JMF,PS,T0.5,149.3X69.5 CLAMP-CORD;-,PE,HB,-,BLK,AA95-00714B70*612,T=0.73,P=0.52 SCREEN-FRESNEL;47W,-,T2,1072*6 SUN SCREEN-AG;47W,-,T=82%,1072*614*2,-,MIRROR-FRONT;47W3,GLASS ,861*677*421,FS BAG-SHEET;-,HDPE PE FOAM,T0.015,W1650,H1 CUSHION SET;47W3,EPS C=0.02 PACKING CASE-IN;47W3,CB H-3 AB,YEL,1207 PACKING CASE-OUT;47W3,CB H-3 AB,YEL,SESA RUBBER-SHEET;47W3,MBR,18*50,T2.0 ASSY-BRACKER,MIRROR;DP,91-00751A 19.5KG, ASSY CHASSIS;SP47W3HFS/XEF ASSY PCB MISC-V/M;DP,PCL545R,P54A ASSY SUB-PCB,SENSOR;DP,PCL545R,P54A,AA95 ASSY SUB-PCB,A/V TERMINAL;DP,SP55W3HF,J5 ASSY SUB-PCB,SUB AMP;DP,SP55W3HF,J52AAA9 ASSY SUB-PCB,A/V FRONT;DP,SP55W3HF,J52A3 ASSY PCB MISC-CRT;DP,SP47W3HF,J52A ASSY SUB-PCB CONTROL;DP,SP47W3HF,J52A,AA ASSY-POWER,CORD;-,CP2/NO(4.0R),H/C150,KJ ADHESIVE-SIL;#9590,WHT,-,CARTRIGE TRANS FBT;FWZ50A001E/FFA97513B,12KV,5P,LEAD CONNECTOR ASSY;P54A/SVP-55W3HD,UL16 TUNER;TCLW3101PD16A(S),PAL/SECAM,181 TUNER;TCPW3001PC16A(S),PAL/SECAM,181 MODULE-FOCUS,PACK;SVP-5200,S300-P3,-,-,BAND-TIE;-,NYLON66 V2,-,-,L100,NTR,CLAMP-WIRE;-,NYLON-6 CLAMP-WIRE;DONG-A,NYLON-66,-,-,-,DATL-60 CLAMP-WIRE;ALL MODEL,NYLON 66,V2,-,BLK,W LABEL-BOX;A/P 90(G),ALL MODEL,-,WHT,L250 LABEL-TRANSFER BOX;-,TF-53B LABEL-RATING;-,TF53B5DF,-,SILVER,5 LABEL-TRANSFER RATING;ALTA RESISTENCI LABEL-WARRANTY;-,-,-,WHT,75MM,20 LABEL-TRANSFER WARRANTY;-,TF-53B5D HOLDER-LEG;-,ABS,-,-,-,BLK, BAG-SHEET;LDPE,T0.08,W150,L120,-,-,BATTERY-ALKALINE;1.5V,750mAH,AAA,10. CABLE-RCA;,1500MM BAG PE;-,HDPE PE FOAM,T0.03,W400,H240 LABEL-BACK,DOLBY;A/P 100(G),CW764AHD,DOL Level Loc. No. Code No. 1 1 1 1 1 1 1 1 1 1 Description ; Specification AA39-30007B 0203-000402 6003-001023 6003-001022 AA68-02303A AA68-02155A AA68-02156A AA68-02415A BP65-00001A AA69-01874A Remark IF-CABLE;-,T,150mm,1365#26 TAPE-KRAFT;KRAFT,T0.17,W18,L50,BLK SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW SCREW-TAPTITE;RH,+,B,M3,L12,ZPC(BLK),SWR MANUAL USERS;W3/T6,HUNGARY,W/P100(G),1,B LABEL-POP,RACK;W3 ,PASCAL, ,REMOVABLE LABEL-POP,AGS;W3 ,PASCAL, ,REMOVABLE CARD-RTF;COLORIT 54 CREMA,MOJO80G,SPA,A TERMINAL-BOARD,ANT;,DP,42W5,AA65-00021A PALLET;ALL MODEL,WOOD,800,1250,120 ASSY-CABINET,WOOD 1 AA90-00970A ASSY-CABINET,WOOD;SP47W3HFS/XEF,47W3 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 2 2 2 2 2 2 2 AA91-00759E AA64-02207A AA60-00078B AA60-10051A AA60-10051B AA61-00094C AA61-00097A AA61-00723A AA61-00507B BP61-00075A AA61-00616B AA61-01117A AA61-00864A AA61-00894B AA61-00894A AA61-00458B AA61-00865A BP61-00087A BP61-00087B AA61-00857B AA61-00858B AA61-10247A AA63-00348B AA65-00014C AA91-00750A AA96-00753A 3001-000151 3001-001107 3001-001134 AA39-00086A AA39-00287A AA39-20609A AA98-00049B 6005-001006 AA60-10050Y AA61-00999A AA61-20219A AA61-01070A AA61-00975A BP63-00001A ASSY-CABINET,WOOD;,WOOD XSA,47W3 CABINET-WOOD;47W3,WOOD SPACER-DUAL,LOCK;W3,#250,19*40 SCREW-WOOD;-,SWRCH18A,M4,L16,PH,+,-,-,ZP SCREW-WOOD;-,SWRCH18A,M3.5,L11,RH,+,-,-, HOLDER-RAIL;PCJ533R,ABS,-,-,-,BLK,HB,480 HOLDER-WIRE;-,NYLON 6/6,-,-,-,NTR,HOLDER-PIN,DABO;PRJT,WOODEN NAIL,OD6XL20 HOLDER-CABINET,WOOD;43,54,62J8,ABS,-,-,HOLDER-JERSEY,ASSY;W3,ABS V0,GRAY,63-000 HOLDER-CRT,MAIN;54J7,DP,-,-,-,-,AA61-005 HOLDER-SENSOR,SIDE;W3,ABS HB,G3676,SIDE HOLDER-PCB;W3,HIPS,V0,BLK HOLDER-SCREEN,TOP;W3,DP,L1082,BLK,61-008 HOLDER-SCREEN,TOP;W3,DP,L1102,BLK,61-008 CASTER;-,TP4020-05 PLY,-,OH56,-,-,SR4 HOLDER-SCREEN,RL;W3,DP,61-00788B 16.2KG RAIL-DOOR,R;W3,ABS HB,BLK RAIL-DOOR,L;W3,ABS HB,BLK BRACKET-NUT,INSERT;W3,M3 ZN BRACKET-FRAME;W3,SECC,T2.0 BRACKET-FOCUS;S46DS,SECC,T1.0,-,-,-,COVER-DUCT;54,62J8,HIPS,-,HB,BLK,-,CLAMP-WIRE;54J9,SINGLE NYLON,-,-,BLK,ASSY-MAGNET,PUSH;,MAGNET,W3 ASSY SPEAKER;,3001-001107) SPEAKER;20W,8ohm,92dB,130Hz SPEAKER;20W,8ohm,95dB,1300Hz SPEAKER;30W,8ohm,93dB,60Hz LEAD CONNECTOR-ASSY;,2.2UF,REC,REC,200MM LEAD CONNECTOR ASSY;PCL54RX,UL2547#26,UL LEAD CONNECTOR-ASSY;,2P,SMH250-02,REC,40 ASSY-LEAD,CON;-,LEAD-CON,CORE,AA39-20505 SCREW-WOOD;FH,+,M3,L15.0,ZPC(BLK),SWRCH1 SCREW-WOOD;-,SWRCH18A,M4,L40,FH,+,-,-,ZP HOLDER-DUAL,LOCK;W3,W1,ABS HB,BLK HOLDER-FRONT,BOT,E;,ABS,HB,L40,BLK HOLDER-CABINET,BOT(D);W3,ABS HB,L990,BLK HOLDER-CABINET,BOT-F;W3,ABS HB,GRAY SHEET-EMI;55W3,PS V2+AL LAMI,T0.35,350* ASSY-DOOR,RACK 1 AA91-00774E ASSY-DOOR,RACK;DP,W3,HB GRAY,64-02066 2 2 2 2 2 2 2 2 AA64-02066C AA64-02206B AA91-00758A AA91-00749A BP61-00128A AA61-00782B AA73-00007B 6003-001019 DOOR-RACK;47.55.65W3,HIPS HB,GRAY,SV808 WINDOW-DOOR;W3,GLASS,T3.0,BR ASSY-HINGE,DOOR(R);SPRING,SECC T1.6 W3,W ASSY-HINGE,DOOR(L);,NO-SPRING SECC T1.6, BRACKET-DOOR;DP,47W3,AA61-00856B BRACKET-MAGNET;W3,SPC,T2.0,FZW RUBBER-CAP;W3,MBR,GRAY,60 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR 7-7 Electrical Parts List Level Loc. No. Code No. Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark ASSY-C/FRONT,MASK 1 AA91-00824D ASSY-C/FRONT,MASK;DP,HB GRAY,02058C 22K 2 2 2 2 AA64-02058C AA64-02211B AA63-00063A AA61-00974A CABINET-FRONT,MASK;47W3,HIPS HB,GRAY,SVM BADGE-BRAND;72MM,AL FORGING,SVM1-126PS,S SPACER-DUAL,LOCK;#400,-,-,19X19,SVP-614J HOLDER-MASK;47H1,HIPS HB,BLK ASSY-C/FRONT,BOT 1 AA91-00775H ASSY-C/FRONT,BOT;DP,64-02063P,47W3 2 2 2 2 2 2 2 2 2 2 2 2 AA64-02063C AA61-00791B AA61-01068A AA64-02205B BP96-00127A 6003-001026 AA61-00785B AA61-00786B AA61-60003J AA64-02080B AA64-02081B AA64-02082B 7-8 CABINET-FRONT,BOT;47W3,,HIPS HB,GRAY,SV8 HOLDER-FRONT,BOT;W3,ABS HB,L40,BLK,D HOLDER-CABINET,BOT(B);W3,ABS HB,L40,BLK, BADGE-DECORATION;W3,NI+AL FORGING+NI,RS ASSY COVER P-HOLDER,CONTROL;DP,W3,ABS HB SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK) GUIDE-KNOB,POWER;W3,ABS HB ,BLK,C HOLDER-CONTROL;W3,ABS HB,WHT,SV104M SPRING-CS;-,SUS304,-,-,OD6, KNOB POWER;W3,ABS HB WHT,SV104M KNOB-CH,VOL;W3,ABS HB,BLK,CH WINDOW-RMC,LED;W3,PC,CLEAR Samsung Electronics Electrical Parts List 7-5 SP47W3HFX/XEC Level Loc. No. Code No. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Description ; Specification AA59-00220A AA94-05093A AA94-05100A AA94-05105A 0203-000402 0203-001329 AA02-00022A 6001-000137 6005-001003 6005-001004 6005-001005 6003-001019 6003-001022 6003-001023 6006-001094 AA60-10011A AA61-00859A AA61-00357F AA61-00972C AA61-00049B AA61-00617B BP61-00033A AA63-00021K AA63-00021L AA63-00021M AA73-00005B AA63-10007C AA63-60131A AA60-00132A AA64-01395Q AA64-02074D AA64-60449B AA91-03604A AA94-11168D AA95-01841C AA95-01790K AA95-01847G AA95-01785E AA94-11166E AA95-01753D AA64-02336A AA64-02225B BP64-00030A AA91-00842K AA91-00843A AA67-00200A AA67-00124B AA67-00132A AA67-00206C AA96-20130A 0201-001059 AA26-00101A AA39-20577B AA40-00094A AA40-00095A AA63-10002A AA65-30008A AA65-30013A AA65-30018A AA65-30104B BP69-00005A BP69-00006A BP69-00007A BP69-00008A AA68-50509A AA68-00344A AA68-00341A AC68-00347A AA68-00340A AA68-00345A AA61-20126A AA63-70002A AA69-30009C Samsung Electronics Remark REMOCON;,TM63,SHARK,51,L/GRAY,EAST ASI ASSY CRT-(R);P16LSG03RJA,+380MG,55,DEL ASSY CRT-(G);P16LSG03HKA,+380MG,55, ,D ASSY CRT-(B);P16LSG03BMB,+380MG,55, ,D TAPE-KRAFT;KRAFT,T0.17,W18,L50,BLK TAPE-OPP MASKING;ANT-300P,T0.07,W15.0,L5 TAPE ETC;SESA,T0.3,75,132,BLK SCREW-MACHINE;BH,+,M3,L8,ZPC(YEL),SM20C, SCREW-WOOD;HH,+,M4,L19,ZPC(BLK),SWRCH18A SCREW-WOOD;HH,+,M4,L27,BLK,SWRCH18A SCREW-WOOD;HH,+,M4.0,L19,NI PLT,SWRCH18A SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR SCREW-TAPTITE;RH,+,B,M3,L12,ZPC(BLK),SWR SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW SCREW-ASS’Y WOOD;WW,HH,+,M7,L32,ZPC(YEL) SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, PLATE-CENTER,SPK;W3,WOOD HOLDER-MIRROR;W3,ABS HB,L430,BLK HOLDER-SCREEN,R;55W3,ABS HB,BLK HOLDER-BOX;-,PP,-,-,-,NTR,V0,AA61-20285A BRACKET-CRT,MAIN;DP,54J7,AA61-00475B BRACKET-MIRROR(TOP);DP,55W3,61-01092A SPACER-MIRROR;50J6,PVC,BLK,HB L500 SPACER-MIRROR,TOP;50J6,PVC HB,BLK,L1020 SPACER-MIRROR,BOT;50J6,PVC HB,L799,BLK RUBBER-CAP;FLAT,PRJ,SILICONE RUBBER,WHIT BAND-PP;-,-,-,W18,-,CLEAR,1G SPACER-FELT;SVP403J,FELT,-,-,-,BLK,T0.5, SPACER-COVER,DUST;DP,W3,T0.5,60-00123B INLAY-TERMINAL;47W3,PS SHEET,T0.5,BLK,J5 INLAY-SPEAKER;T6,W3,PS SHEET,T0.5,J52A P INLAY-COVER;SP-434JMF,PS,T0.5,149.3X69.5 ASSY CHASSIS;SP55W3HFS/XET ASSY PCB MISC-V/M;DP,PCL545R,P54A ASSY SUB-PCB,SENSOR;DP,PCL545R,P54A,AA95 ASSY SUB-PCB,A/V TERMINAL;DP,SP55W3HF,J5 ASSY SUB-PCB,SUB AMP;DP,SP55W3HF,J52AAA9 ASSY SUB-PCB,A/V FRONT;DP,SP55W3HF,J52A3 ASSY PCB MISC-CRT;DP,SP47W3HF,J52A ASSY SUB-PCB CONTROL;DP,SP47W3HF,J52A,AA CABINET-BACK,BOT;W3,HIPS,V0,BLK CABINET-BACK,SIDE;DP,47.55W3,HIPS HB,BLK CABINET-BACK,TOP;DP,55W3,BP64-00014A ASSY-C/FRONT,BOT;DP,64-02064P,EUP,55,65W ASSY-C/FRONT,MASK;DP,64-02059C,55W3 SCREEN-TINT;55W,1249*710,T=0.73,P=0.52 SCREEN-FRESNEL;55W,-,T2,1251*712,-,-,-,SUN SCREEN-AG;55W,-,T=82%,1251*712*2,-,MIRROR-FRONT;DP,55W9,FSM,1027*799*540 ASSY-POWER,CORD;-,CP2/NO(4.0R),H/C150,KJ ADHESIVE-SIL;#9590,WHT,-,CARTRIGE TRANS FBT;FWZ50A001E/FFA97513B,12KV,5P,LEAD CONNECTOR ASSY;P54A/SVP-55W3HD,UL16 TUNER;TCLW3101PD16A(S),PAL/SECAM,181 TUNER;TCPW3001PC16A(S),PAL/SECAM,181 BAND-TIE;-,NYLON66 V2,-,-,L100,NTR,CLAMP-CORD;-,PE,HB,-,BLK,CLAMP-WIRE;-,NYLON-6 CLAMP-WIRE;DONG-A,NYLON-66,-,-,-,DATL-60 CLAMP-WIRE;ALL MODEL,NYLON 66,V2,-,BLK,W CUSHION;55W3NEW,EPS,C=0.02 PACKING CASE;55W3,H-3 AB,C-1,1397,762,15 PACKING-COVER,TOP;55W3,H-3 AB,C-1,1769,1 PACKING-COVER,BOT;55W3(NEW),H-3 AB,C-1,1 LABEL-BOX;A/P 90(G),ALL MODEL,-,WHT,L250 LABEL-TRANSFER BOX;-,TF-53B LABEL-RATING;-,TF53B5DF,-,SILVER,5 LABEL-TRANSFER RATING;ALTA RESISTENCI LABEL-WARRANTY;-,-,-,WHT,75MM,20 LABEL-TRANSFER WARRANTY;-,TF-53B5D HOLDER-LEG;-,ABS,-,-,-,BLK, SHEET;-,PE FOAM,T1.0,-,-,-,50G BAG-SHEET;LDPE,T0.08,W150,L120,-,-,- Level Loc. No. Code No. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Description ; Specification 4301-000115 AA39-40001B AA69-00862A AA69-30036A AA39-30007B AA68-50523A AA68-01777A AA68-02013A AA68-02155A AA68-02156A 6801-001017 AA68-02415A AA59-00171A BP65-00001A AA69-01088U Remark BATTERY-ALKALINE;1.5V,750mAH,AAA,10. CABLE-RCA;,1500MM BAG PE;-,HDPE PE FOAM,T0.03,W400,H240 BAG-PE;HDPE,T0.02,2000,1800,-,-,555J, IF-CABLE;-,T,150mm,1365#26 LABEL-BACK,DOLBY;A/P 100(G),CW764AHD,DOL MANUAL USERS;W3,SPA,W/P100(G),1,B5,J52A, MANUAL USERS;W3,POR,W/P100(G),1,B5,J52A, LABEL-POP,RACK;W3 ,PASCAL, ,REMOVABLE LABEL-POP,AGS;W3 ,PASCAL, ,REMOVABLE CARD REGISTRATION;XEC,SPANISH,MOJO100,L1 CARD-RTF;COLORIT 54 CREMA,MOJO80G,SPA,A MODULE-FOCUS,PACK;SVP-5200,S300-P3,-,-,TERMINAL-BOARD,ANT;,DP,42W5,AA65-00021A PALLET-SET;55W3(NEW),PAPER,1415,780,130 ASSY-DOOR,RACK 1 AA91-00774E ASSY-DOOR,RACK;DP,W3,HB GRAY,64-02066 2 2 2 2 2 2 2 2 AA64-02066C AA64-02206B AA91-00758A AA91-00749A BP61-00128A AA61-00782B AA73-00007B 6003-001019 DOOR-RACK;47.55.65W3,HIPS HB,GRAY,SV808 WINDOW-DOOR;W3,GLASS,T3.0,BR ASSY-HINGE,DOOR(R);SPRING,SECC T1.6 W3,W ASSY-HINGE,DOOR(L);,NO-SPRING SECC T1.6, BRACKET-DOOR;DP,47W3,AA61-00856B BRACKET-MAGNET;W3,SPC,T2.0,FZW RUBBER-CAP;W3,MBR,GRAY,60 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR ASSY-CABINET,WOOD 1 AA91-00760B ASSY-CABINET,WOOD;,WOOD XSA,55W3 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 6005-001006 AA60-10050Y AA60-00078B AA60-10051A AA60-10051B AA61-00094C AA61-00097A BP61-00031A BP61-00032A AA61-00999A AA61-00458B AA61-00507B BP61-00075A AA61-00506B AA61-01117A BP61-00087A BP61-00087B AA61-00857B AA61-00858B BP61-00034A AA61-00722A AA61-00864A AA61-00788C AA61-00878C AA61-00878D AA63-00348B AA63-60126E AA63-60126F AA63-60126G AA64-02208B AA65-00014C AA91-00750A 3001-000151 3001-000153 3001-001116 SCREW-WOOD;FH,+,M3,L15.0,ZPC(BLK),SWRCH1 SCREW-WOOD;-,SWRCH18A,M4,L40,FH,+,-,-,ZP SPACER-DUAL,LOCK;W3,#250,19*40 SCREW-WOOD;-,SWRCH18A,M4,L16,PH,+,-,-,ZP SCREW-WOOD;-,SWRCH18A,M3.5,L11,RH,+,-,-, HOLDER-RAIL;PCJ533R,ABS,-,-,-,BLK,HB,480 HOLDER-WIRE;-,NYLON 6/6,-,-,-,NTR,BRACKET-F/MIRROR(R);DP,55W3,61-01090A BRACKET-F/MIRROR(L);DP,55W3,61-01091A HOLDER-DUAL,LOCK;W3,W1,ABS HB,BLK CASTER;-,TP4020-05 PLY,-,OH56,-,-,SR4 HOLDER-CABINET,WOOD;43,54,62J8,ABS,-,-,HOLDER-JERSEY,ASSY;W3,ABS V0,GRAY,63-000 HOLDER-CRT,MAIN;43,54,62J8,HIPS,-,-,-,BL HOLDER-SENSOR,SIDE;W3,ABS HB,G3676,SIDE RAIL-DOOR,R;W3,ABS HB,BLK RAIL-DOOR,L;W3,ABS HB,BLK BRACKET-NUT,INSERT;W3,M3 ZN BRACKET-FRAME;W3,SECC,T2.0 BRACKET-MIRROR(BOT);DP,55W3,61-01093A HOLDER-PIN,DABO;PRJT,NYLON,OD6.5XL25,-,HOLDER-PCB;W3,HIPS,V0,BLK HOLDER-SCREEN,L;55W3,ABS HB,L686,BLK HOLDER-SCREEN,TOP;W3,ABS HB,L1282,BLK HOLDER-SCREEN,BOT;W3,ABS HB,L1262,BLK COVER-DUCT;54,62J8,HIPS,-,HB,BLK,-,SPACER-FELT;,FELT,BLK,T2,275X15 SPACER-FELT;,FELT,BLK,T2,310X15 SPACER-FELT;,FELT,BLK,T2,712X15 CABINET-WOOD;55W3,WOOD,XSA CLAMP-WIRE;54J9,SINGLE NYLON,-,-,BLK,ASSY-MAGNET,PUSH;,MAGNET,W3 SPEAKER;20W,8ohm,92dB,130Hz SPEAKER;20W,8OHM,93DB,1.3KHZ SPEAKER;30W,8ohm,96dB,60Hz 7-9 Electrical Parts List Level Loc. No. Code No. 2 2 2 2 2 2 2 2 2 2 2 2 7-10 AA39-00086A AA39-00272B AA39-20609A AA98-00049B 6005-001003 AA60-10011A AA61-01067A AA61-20219A AA61-01070A AA61-10247A BP63-00001A AA61-00971C Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark LEAD CONNECTOR-ASSY;,2.2UF,REC,REC,200MM LEAD CONNECTOR ASSY;,UL2547#26,UL/CSA,12 LEAD CONNECTOR-ASSY;,2P,SMH250-02,REC,40 ASSY-LEAD,CON;-,LEAD-CON,CORE,AA39-20505 SCREW-WOOD;HH,+,M4,L19,ZPC(BLK),SWRCH18A SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, HOLDER-CABINET,BOT(A);W3,ABS HB,L40,BLK, HOLDER-FRONT,BOT,E;,ABS,HB,L40,BLK HOLDER-CABINET,BOT(D);W3,ABS HB,L990,BLK BRACKET-FOCUS;S46DS,SECC,T1.0,-,-,-,SHEET-EMI;55W3,PS V2+AL LAMI,T0.35,350* HOLDER-SCREEN,TB;55W3,ABS HB,L1282,BLK Samsung Electronics Block Diagrams 8. Block Diagram 8-1 Main Signal(Progressive) Samsung Electronics 8-1 Block Diagrams 8-2 Video Signal 8-2 Samsung Electronics Block Diagrams 8-3 Sound Signal Samsung Electronics 8-3 Block Diagrams 8-4 Power Supply C 8-4 Samsung Electronics Block Diagrams 8-5 In/Out by Block Samsung Electronics 8-6 Signal Connection by Block 8-5 Wiring Diagrams 9. Wiring Diagram 9-1 Pcb Connection(Progressive) Samsung Electronics 9-1 Schematic Diagrams 10. Schematic Diagrams 10-1 MAIN 1 Samsung Electronics 10-1 Schematic Diagrams 10-2 MAIN 2 10-2 Samsung Electronics Schematic Diagrams 10-3 MAIN 3 TP01 TP02 TP01 TP02 Samsung Electronics 10-3 Schematic Diagrams 10-4 MAIN 4 10-4 Samsung Electronics Schematic Diagrams 10-5 MICOM(CS) with out, TTX TP03 TP04 TP03 TP04 Samsung Electronics 10-5 Schematic Diagrams 10-6 MICOM(CS) with in, TTX TP03 TP04 TP03 TP04 10-6 Samsung Electronics Schematic Diagrams 10-7 MICOM(CW) Samsung Electronics 10-7 Schematic Diagrams 10-8 POWER 10-8 Samsung Electronics Schematic Diagrams 10-9 POWER with in PFC Samsung Electronics 10-9 Schematic Diagrams 10-10 SOUND 10-10 Samsung Electronics Schematic Diagrams 10-11 CRT Samsung Electronics 10-11 Schematic Diagrams 10-12 SUB 1 TP09 TP10 TP11 TP05 TP06 TP07 TP08 10-12 TP12 Samsung Electronics Schematic Diagrams 10-12-1 SUB 1 WAVEFORMS TP12 TP06 TP07 TP08 TP09 TP10 TP11 2000/11/04 12:17:04 NORM:50MS/s Stopped 20us/div (20us/div) =Trace1= P-P 37.00V Max 19.80V Min -17.20V Rms 6.783V Avg -11.18mV Freq --Brst --- CH1=5V AC 10:1 =Filter= Smoothing : OFF BW : FULL Samsung Electronics =Offset= CH1 : ------CH2 : 0.0V CH3 : 0.0V CH4 : 0.0V =Record Length= Main : 10K Zoom : 10K =Trigger= Mode : AUTO Type : EDGE CH1 Delay : 0.0ns Holdoff : 0.2us 10-13 Schematic Diagrams 10-13 SUB 2 TP13 TP14 TP13 TP14 10-14 Schematic Diagrams 10-14 SUB 3 TP15 2000/11/08 20:20:46 NORM:50MS/s Stopped 20us/div (20us/div) =Trace1= P-P 344.0V Max 342.0V Min -2.000V Rms 156.5V Avg 146.5V Freq 45.45kHz CH1=50V DC 10:1 =Filter= Smoothing : OFF BW : FULL =Offset= CH1 : 0.0V CH2 : 0.0V CH3 : 0.0V CH4 : ------- =Trigger= Mode : AUTO Type : EDGE CH4 Delay : 0.0ns Holdoff : 0.2us =Record Length= Main : 10K Zoom : 10K TP16 2000/11/07 20:58:36 NORM:50MS/s 20us/div (20us/div) Stopped =Trace1= P-P 111.2mV Max 54.40mV Min -56.80mV Rms 23.79mV Avg 1.947mV Freq 21.74kHz CH1=20mV AC 10:1 =Filter= Smoothing : ON BW : FULL =Offset= CH1 : ------CH2 : 0.000V CH3 : 0.00V =Record Length= Main : 10K Zoom : 10K =Trigger= Mode : AUTO Type : EDGE CH1 Delay : 0.0ns TP17 TP15 TP17 TP16 Samsung Electronics 10-15 Schematic Diagrams 10-15 A/V TERMINAL 10-16 Samsung Electronics Schematic Diagrams 10-16 CONVERGENCE TP18 TP19 TP20 TP18 TP19 TP20 TP21 TP22 TP23 TP21 TP22 TP23 Samsung Electronics 10-17 Schematic Diagrams 10-17 CONVERGENCE(SDC11 1/2) 10-18 Samsung Electronics Schematic Diagrams 10-18 CONVERGENCE(SDC11 2/2) Samsung Electronics 10-19 Schematic Diagrams 10-19 PERFECT FOCUS (PHOTO SENSOR & INTERFACE BOARD) 10-20 Samsung Electronics Schematic Diagrams 10-20 AV FRONT Samsung Electronics 10-21 Schematic Diagrams 10-21 CONTROL, VM CONTROL 10-22 VM Samsung Electronics Schematic Diagrams 10-22 DW 1 Samsung Electronics 10-23 Schematic Diagrams 10-23 DW 2 10-24 Samsung Electronics Schematic Diagrams 10-24 DW 3 TP28 TP27 TP32 TP31 TP34 TP33 Samsung Electronics TP30 TP29 TP26 TP25 TP24 10-25 Schematic Diagrams 10-24-1 DW 3 WAVEFORMS TP24 TP30 TP25 TP31 TP26 TP32 TP27 TP33 TP28 TP34 TP29 10-26 Samsung Electronics Schematic Diagrams 10-25 SUB AMP/PFC SUB AMP Samsung Electronics PFC 10-27 Schematic Diagrams 10-26 FORMAT-CONVERTER 10-28 Samsung Electronics
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : 3.1-702 Modify Date : 2008:07:20 11:15:20+02:00 Create Date : 2008:07:20 11:15:20+02:00 Metadata Date : 2008:07:20 11:15:20+02:00 Format : application/pdf Document ID : uuid:379d9d8a-193e-408b-b0ba-229f61af8c8b Instance ID : uuid:3a440396-0641-4475-a5bd-64667bdacccf Producer : Acrobat Distiller 4.0 for Macintosh Page Count : 118 Creator : QuarkXPressª: AdobePS 8.5.1EXIF Metadata provided by EXIF.tools