SLX Scissor Lift Inst
User Manual: SLX
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
Installation/Operating Instructions Scissor Lift SLX Video Projector Lift by Draper Caution: Important Safety Instructions Read all instructions completely before proceeding. DANGER: To reduce risk of shock: WARNING/AVERTISSEMENT Electrical Connections Unit operates on 115V AC, 60 Hz. current. 10.93 amps current draw (3.93 amps for lift, 7 amps for outlet). RISK OF ELECTRIC SHOCK. DO NOT OPEN RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR. 1 Always disconnect power from lift before cleaning. WARNING–To reduce risk of burns, fires, electric shock or injuries to persons: 2 Disconnect power from lift before putting on or taking off parts. 3 Use this lift only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer. 4 Never operate this lift if it has a damaged cord or plug. If it is not working properly, call your dealer or the manufacturer for assistance/repair. 5 Keep cords away from heated surfaces. 6 Never operate lift with air opening blocked. Keep the air openings free of lint, hair, and the like. 7 Never drop or insert any object into any opening. 8 Do not use outdoors. 9 Route cords and cables as shown in the instructions. 10 WARNING: Rick of Electric Shock— connect this product to a properly grounded electrical supply. Important installation/operating Instructions WARNING: To prevent injury, this apparatus must be securely attached to the building structure in accordance with the instructions. 11 Test lift prior to installation. Please Note: Packaging must be removed from lift before testing. 12 Follow instructions carefully. Installation contrary to instructions invalidates warranty. 13 Do not obstruct operation of Scissor Lift SLX with fingers or any object. Serious injury or damage could result. 14 Lift is intended for use with product weighing not more than 350 pounds. 15 Scissor Lift SLX is designed to accommodate ceiling suspended equipment. Equipment should not be allowed to rest on optional ceiling closure during operation (refer to section titled “Installing Projector”). 16 Entire bottom of unit must be unobstructed to permit proper operation. Sufficient clearance must be allowed below projector or optional ceiling closure: 10' for Model SLX10, 14' for Model SLX14, etc. 17 Unit must be installed level (use a carpenter’s level). 18 Unit operates on 115V AC 60 Hz. current. 10.93 amps current draw (3.93 amps for lift, 7 amps for outlet). 19 Verify the show position when testing lift. Make required changes by referring to adjustment instructions on page 4 of this document. 20 The maintenance/service factory limit setting must not be adjusted to a lower position than the preset factory limit setting. In addition, Draper does not recommend setting show position at the maintenance/service position—for example, if you wish to have 8' show position, order a lift with at least a 10' maintenance position. 21 When the Scissor Lift SLX is to be installed in “other space used for environmental air” the optional environmental air space housing must be installed per instructions to isolate the lift from the “other space used for environmental air.” 22 When Scissor Lift SLX is NOT installed in environmental air space housing and optional ceiling closure, the ALTERNATE wiring for up limit switch may be used (see Alternate Wiring schematic on page 5). CAUTION: Before servicing unit, disconnect hardwired control and any remote control. Note: Unit has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment. Opening the electrical box exposes terminals for field connections. Unit is shipped with internal wiring complete. Wire to connect unit to power supply should be furnished by installer. Connections should be made in accordance with wiring diagram, and wiring should comply with national and local electrical codes. An appropriate disconnect device shall be provided as part of the building installation. All operating switches should be “off” before power is connected. Caution: Make sure electrical supply has been disconnected before attempting to connect Scissor Lift to electricity. Scissor Lift should be operated and checked prior to installing projector and/or optional ceiling closure. Low Voltage Control Switch shown on Page 2 comes with 22.8 m of nonplenum rated cable and should be plugged in to Control Panel on top frame of lift for control of the "Up" and "Show" positions. Momentary Key Switch shown on Page 2 comes with 22.8 m of cable and should be plugged in to Control Panel on top frame of lift for control of the "Service" position. Planning 1 Based on screen location and projector specifications, determine proper position for projector installation. 2 Confirm that there is adequate space for installation and operation. Minimum clearance above ceiling level varies according to Scissor Lift model, plus height of projector, optional mounting bracket, optional ceiling closure, and optional Environmental Air Space Housing. 3 Arrange to provide service access to the unit. 4 Maximum lifting capacity is 350 kg. As Soon As Scissor Lift Arrives 1 Open carton and inspect for damage. 2 Locate the following parts: A. The unit itself B. Controls C. Optional equipment: I. Environmental Air Space Housing, II. Universal Projector Mount, III. Closure Panel or Ceiling Finish Kit (all ship in separate cartons). 3 Test lift prior to installation. Please Note: Packaging must be removed from lift before testing. Caution: Caution: Beware of pinch points Beware of pinch points Copyright © 2014 Draper Inc. Form ScissorLiftSLX_Inst14-R Printed in U.S.A. If you encounter any difficulties installing or servicing your Scissor Lift SLX, call your dealer or Draper, Inc. in Spiceland, Indiana, 765-987-7999, or fax 765-987-7142. Scissor Lift SLX by Draper Operation Hanging Unit Please note: If using Environmental Air Space Housing option, go to Environmental Air Space Housing instructions on page 8. The Scissor Lift may be installed in a variety of ways; recessed above the ceiling, or suspended below the ceiling. The lift should be supported by four ½" threaded mounting rods or bolts with locking nuts. If ceiling recessed, the entire unit (including the projector) should set approximately 1½" above the finished ceiling in its “stored” position. The threaded rods should pass through the corner mounting flanges and be secured by nuts above and below. The unit should then be guy wired or blocked to prevent swinging. All installations should observe the following guidelines: 1 If installing above a hard ceiling, optional Draper Access Panels are available to allow access to the unit. 2 Installer must ensure that all fasteners and supports are of adequate strength to securely support Scissor Lift and projector. 3 Fastening methods must be suitable for mounting surface, and securely anchored so that vibration or abusive pulling on unit will not weaken installation. 4 Unit should be level, with weight shared more or less equally by all four threaded mounting rods. 5 Bottom of unit must be unobstructed after installation. Sufficient clearance must be allowed below projector or optional ceiling closure. 6 Unit must be secured independent from suspended ceiling and do not use unit to support adjacent ceiling, light fixtures, etc. 7 Unit to be installed so when lowered to its lowest point, it is a minimum of 8 feet (2.44 m) above the floor. 8 Do not complete the ceiling below unit until electrical connections have been completed and unit has been operated successfully. 9 We recommend that safety cables be attached to the Scissor Lift SLX for added security (a sound installation practice with overhead equipment). 10 When the Scissor Lift SLX is to be installed in “other space used for environmental air” the optional Environmental Air Space Housing must be installed per instructions to isolate the lift from the “other space used for environmental air.” 11 When Scissor Lift SLX is NOT installed in environmental air space housing and optional ceiling closure, the ALTERNATE wiring for 'UP' limit switch may be used. Disconnect both BLACK (BK) wires from 'UP' limit switch and quick connect them together using the provided jumper cable (see Alternate Wiring Caution: schematic on page 5). page 2 of 8 Before operating or testing the unit, make sure the packaging has been removed from the unit. Remove the corrugated block from the cardboard sleeve (bottom-most packaging material), then collapse the sleeve and remove it, along with the rest of the packaging. Next, using the 3 button switched, operate the lift in the "up" direction, so the lift's control encoder will recognize it's "home" location. Until you do this, the Down function will not work. You must also do this if the Scissor Lift ever loses or is disconnected from the power. When unit is first operated, be cautious! If unit fails to operate properly, press “STOP” and recheck electrical connections before proceeding. Cycle unit down and up several times to confirm satisfactory operation. Caution: Do not pull on or touch safety belt when unit is in motion. If belt locks, the cables will unspool. Caution: Obstructing bottom pan may cause cables to unspool. Caution: Do not operate Scissor Lift SL without a minimum of 15 lbs. of weight attached to the pan. Operating without weight may cause cables to unspool. Lift LV Switch SP-KSM Standard Single Station Low Voltage Control 7 /8 " Up &2¾" Show Service (See Fig. 1)— One three-button switch with “UP”, “DOWN”, and “STOP” buttons. Lift starts up or down when appropriate button is pressed, and may be stopped 4½" by pressing “STOP” button. Factory set limit switches stop lift automatically when projector is in “show” position. One momentary key switch lowers lift from “show” to “service” position. FrontFigure 1Side Back Optional Multiple Station Control— Optional, moves lift from “stored” to “show” position only. Each switching station has a three-button switch with “UP”, “DOWN”, and “OFF” buttons. Lift starts up or down when appropriate button is pressed, and may be stopped by pressing “OFF” button. Factory set limit switches stop lift automatically when projector is in “show” position. UP UP OFF OFF DOWN DOWN DCU Optional Key Operated Switch— If ordered, the standard Lift LV Switch can be replaced with a second single station, momentary key-operated three position (up/off/down) switch. Multiple Station Control required for this option. Moves lift from “stored” to “show” position only. Optional Infrared or Radio Frequency Remote Control—If ordered, a threebutton transmitter is provided, with “UP”, “DOWN”, and “STOP” buttons. Unit starts up or down when appropriate button is pressed, and may be stopped by pressing “OFF” button. Factory set limit switches stop unit automatically when projector is in “show” position. Only controls "show" and "stored" positions. Optional RS232 Control—For Serial communication an R2D7 Serial Communications Interface is optionally available. Caution: Beware of pinch points Low Voltage Trigger—Input provided for Low Voltage Trigger from projector (see diagram on page 4). Beware of pinch points Please Note: Scissor Lift SLX must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC), CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70, as required. An appropriate disconnect device shall be provided as part of the building installation. Scissor Lift SLX is approved to UL 2442 and CSA C22.2 No. 60065-03. Adjusting for Level or Center of Gravity (See Fig. 2 Below) Preferred Method—Adjusting Projector Pan 1 2 3 4 5 6 The Projector Pan can be moved forward or back. Make sure Bottom Pan is supported. Remove the Lifting Cable Bar. Remove screws holding Projector Pan on Bottom Pan. Move Projector Pan forward or back. Replace screws. Replace Lifting Cable Bar. Attachment points for Lifting Cables Lifting Cable Bar 3 /8"-18 x 1" hex head cap screws for attaching Lifting Cable Bar to Bottom Pan Figure 2 Projector Pan Secondary Method—Adjusting Lifting Cable Bar (if above does not work) Run the unit to its "Service" position and make sure Bottom Pan is level. Try and set so that bottom pan is not more than ¾" out of level. However, the pan does not have to be perfectly level, as long as the positioning is consistent and repeatable in "Show" and "Closed" positions. 1 2 3 4 5 Make sure Bottom Pan is supported. Remove screws holding Lifting Cable Bar to the Projector Pan. Move Lifting Cable Bar forward or back. Replace screws. Check level again. If still not level, repeat. www.draperinc.com ¼"-20 x ¾" hex head cap screws for attaching Projector Pan to Bottom Pan Bottom Pan (765) 987-7999 Scissor Lift SLX by Draper page 3 of 8 Installing Projector Generally, the video projector should be suspended from the Projector Pan according to projector manufacturer’s instructions and recommended standard ceiling mounting hardware. Installing Projector Using Universal Projector Mount (Maximum Capacity 26 lbs) See Installation Instructions included with Universal Pojector Mount. Projector should be bolted to projector pan as in a normal ceiling mounting. Equipment should not be allowed to rest on optional ceiling closure during operation. Figure 3 The Scissor Lift SLX has a grounded 115V AC, 60 Hz outlet for projector power supply. Control cables should be laced through our Cable Management System on rear scissor mechanism only. Route the cables and attach with plastic wire ties similar to factory installed power cable. Make sure to use flexible cables. Plenum rated cables are typically too stiff and should not be used. Installer is responsible for ensuring cables do not stretch, kink, or interfere with the scissor mechanism as the unit raises and lowers. This will ensure that cords do not become tangled and damaged during Scissor Lift SL operation. Unit and projection system should be operated, checked and adjusted as necessary at this time. NOTE: Immediately upon completion of the surrounding ceiling, units should be operated to confirm that optional ceiling closure panel stops just short of touching ceiling in closed position. 2½" 5½" (64mm) Warning: Keep fingers and other objects away from automatic ceiling closure and scissor mechanisms when unit is 12" (305mm) operating. Serious injury or damage could result. 7" (140mm) (178mm) 10" (254mm) 12" (305mm) 7" (178mm) 2½" (64mm) 5½" 315/16" (100mm) (140mm) 12" (305mm) 10" (254mm) 12" (304mm) Attaching Universal Projector Mount to Projector Pan If you ordered the unit with optional Universal Projector Mount pre-installed, disregard these instructions. 12" (305mm Figure 4 If you did not order the mount pre-installed, you will need to install a new Projector Pan, which includes the Universal Projector Mount's rectangular plate. 1 Lower unit until the Bottom Pan is resting on a tabletop or other stable and sturdy surface. 2 Remove Lifting Cable Bar from Bottom Pan (see Fig. 2). 3 Remove bolts holding Projector Pan to Bottom Pan (see Fig. 2). 4 Remove Projector Pan and set aside. 5 Place new Projector Pan with Universal Mount into place. 7" 6 Re-attach Projector Pan to Bottom Pan. (178mm) 7 Re-attach Lifting Cable Bar to Bottom Pan. 21/16" (52mm) 315/16" (100mm) 12" (304mm) www.draperinc.com (765) 987-7999 21/16 (52mm Scissor Lift SLX by Draper page 4 of 8 Installing Optional Ceiling Closure If your Scissor Lift SLX is equipped with optional ceiling closure, it can be used as is, or in conjunction with a square of existing ceiling tile (see Fig. 5). 1 If installing with ceiling tile, you may need to cut tile so that its overall dimensions are the same as (or slightly less than) the closure panel. Place tile into trim frame. Lay closure panel on top (back side) of ceiling tile, and tighten screws to hold in place. Lipless Closure Option is available by removing the Trim Ring from the Closure Panel. A substrate material (ceiling tile, gypsum board, etc.) can be attached directly to the Closure Panel using adhesive, double-sided tape or screws. NOTE: Make sure the added weight of the substrate does not exceed the stated weight capacity of the lift. Substrate should be installed so that it is centered within the finished opening in the ceiling, with a gap of no less that 3/16" around all edges. Lipless Closure dimensions shown with in drawing below. 2 Attach provided angle brackets to side of Bottom Panel of Scissor Lift SLX. 3 Attach threaded rods to angle bracket. 4 Run unit “up” until bottom pan stops at highest position. Mark position on rods even with ceiling level and cut to length (remove from pan if convenient). 5 Run unit “down” until bottom pan stops at “show” position. 6 Attach closure to lower end of rods by slipping into four corner slots and secure with nuts above and below slots. Caution: Make sure nuts are completely tightened. 7 Run unit “up” again to highest position. Measure distance by which panel fails to reach required “closed” height for surrounding ceiling. 8 Run unit “down” then re-adjust mounting of threadedrods in traveling grid to raise panel required distance. 9 Test unit operation to confirm that panel will stop in closed position just before touching ceiling. 8 Figure 5 For Additional Safety: 1 Be sure the nuts that attach the threaded rods to the closure panel are tight. 2 Wrap a plastic wire tie around the mounting tab and the threaded rod at all four corners of the closure panel (see drawing). Please Note: Do NOT use a paper-covered or similar wire tie— use only plastic wire ties for maximum safety. Installing Optional Ceiling Trim Kit The Scissor Lift SLX is available with a Ceiling Trim Kit, which consists of the lower section of the Environmental Air Space Housing and the optional closure panel (see Fig. 6). 1 Install Scissor Lift SLX as previously described in these instructions. 2 Install bottom section of Environmental Air Space Housing and Trim Ring in opening. This can be accomplished by suspending with wire, or by mounting directly to the ceiling joists (if space permits). 3 Install projector and attach optional ceiling closure to Scissor Lift SLX, according to the instructions included in this document. Lower section of Environmental Air Space Housing 3 2 7 * PLEASE NOTE: Immediately upon completion of the surrounding ceiling, unit should be operated to confirm that optional ceiling closure panel by Draper or by others stops 1/8" short of touching ceiling in closed position. If closure panel touches, the motor may continue operating after the lift is closed. If it continues to cycle once the lift is closed, a motor failure may occur. 9 4 7 5 6 1 Item Qty Part Number Description 1 1 C028.546 Frame, SLX Closure Trim 2 1 C044.181.07SA Panel, SLX Assembled Closure 3 2 C002.845.07SA Bracket, SLX Closure 4 4 C077.035.49 Rod 3/8"-16 x 177/8" L Threaded , Zinc 5 8 C013.050 Washer .375 I.D. x .875" O.D. x .064" TK GRD 2 Zinc Flat 6 8 C020.082 Screw, 10-16 X ½" 6 Lobe Truss Head AB E-White 7 16 C018.027 Nut, 3/8"-16 Hex GRD 2 NSF 8 4 C020.322 Screw, 5/16"-18 x ¾" Long Grade 5 HH Zinc 9 4 C018.045 Nut, 5/16"-18 Zinc Hex KEPS Scissor Lift SLX Inspection and Maintenance Draper recommends inspecting the Scissor Lift SLX at least annually or every 300 cycles—whichever comes first. A recommended maintenance schedule includes: -Cables: Check for fraying. -Drive Chain Gears: Check for rust, breaks, secure attachment. -Fasteners along scissor arm assemblies: Make sure they are not loose. If any are loose, hand tighten the nuts. Figure 6 Please Note: There is no need to tighten nut in the top scissor which slides back and forth in the side slot in the lift. Tightening this fasteners assembly will cause the unit to lock up and lead to damage to the unit. -Closure: Make sure threaded rod remains seated firmly in the closure panel corners, and that nuts remain tight. If they are loose, tighten them. Trim Ring Ceiling tile (by others) www.draperinc.com (765) 987-7999 Scissor Lift SLX by Draper page 5 of 8 Connecting Controls to Data Cable Splitter Board Controls plug into the Data Cable Splitter Board (See diagram below) which is located on the Top Frame on the front side of the lift, using RJ14/6P4C connectors. For IR or RF Remote Control, use data cable with RJ14/6P4C connectors on both ends. For serial control of "Show" position, use data cable with RJ14/6P4C connectors on both ends and an R2D7 Serial Control Interface. Plug into the "RP/RQ" input. Function Indicator Low Voltage Trigger (6-24 VDC) (Polarity Independent) Please Note: Data cable connections must be made using electrically straight 6 Pin 4 conductor modular cable (RJ14/6P4C). Red - Down Black - Com Black - Com Blue - Up SP-KSM Key SwitchService Position Please Note: Any control, including automated dry contact systems, being connected to the wall switch input MUST send a momentary signal. LVT RP/RQ PIN 1 - NOT USED 2 - YELLOW 3 - GREEN 4 - NOT USED 5 - BLACK 6 - NOT USED WALL KEY Figure 7 RP/RQ DETAIL OF DATA CABLE SPLITTER BOARD RP/RQ Bus Ports for remote controls such as IR Eye, RF Receiver, LED Wall Switch and RS232. Optional R2D7, RS232 Controller Pin 3 - Green Pin 5 - Black Pin 2 - Yellow LVC-S Show Position DCU Yellow Black Green Clearing and Resetting Show Position CLEARING THE SHOW POSITION AT CURRENT SHOW POSITION: 1 Move lift to the show position. 2 While lift is at the show position press and hold the Key Up toggle switch and release once the Lift begins moving upward. 3 The show position is now cleared and ready for a new show position to be set. Please Note: Data Cables for Serial Control Provided by Others To RS232 Serial Port: Blue = Not Used Yellow = Rx (Data from control system) Green = Tx (Data to control system) Red = Not Used Black = Gnd (Signal Ground) White = Not Used Optional Delay Feature 1 When the Optional Delay Feature is installed the Delay Switch must be in the "Delay On" position for normal operation. KEEP DELAY IN OFF POSITION WHEN CURRENT SENS OR IS NOT USED NOTICE - Delay Featu re Will Not Operate Properly Witho The Optional Current Sensout r Connected To The Lift. PLEASE NOTE: At this point the Key Switch will not operate until the new “Show Position” has been set. Also the 3-Button Wall Switch changes into a maintain, push and hold type button, for continuous movement. This allows for easy setting of new “Show Position”) PROCEDURE FOR SETTING SHOW POSITION: 1 Now that the show position has been cleared, use wall switch up and down buttons to get lift into desired show position. 2 While lift is at desired show position, press and hold the Key Down toggle switch until lift begins to move upward. Lift will begin a calibration cycle where it will move upward for two seconds, stop then move down for one second and then the Lift will return to the desired show position. www.draperinc.com 2 If the Optional Delay Feature is installed and the "Show Position" requires adjusting, then the "Delay Switch" must be switched to OFF while adjusting the show position. CAUTION: Be sure all switches are in OFF position before adjusting limit switch. Always be prepared to shut lift off manually when new adjustment is being tested. Please refer to wiring diagram. PLEASE NOTE: If the Scissor Lift loses power, the DOWN function will not work until you operate the lift in the UP direction using the wall switch. This allows the lift's control encoder to recognize it's "home" location. (765) 987-7999 Scissor Lift SLX by Draper page 6 of 8 Adjusting Limit Switches PLEASE NOTE: Changing the fully open or fully closed position will reset the electronic controls and cause the lift to operate improperly. Please call Draper before attempting these adjustments. Adjusting FULLY DOWN position Limit switches for the Scissor Lift SL are preset at the factory. The DOWN limit switch is set for the fully down (maintenance) position for the size lift you have ordered. The limit switch assembly is located inside the lift and behind the Lifting Cable Drum. Figure 8 The Down limit switche shown in the drawing are for setting the "Fully Down" position. This can be adjusted manually by loosening or tightening the screw to increase or reduce the travel. DOWN Limit Switch DOWN ROTATE R OTATE T O TO A DJUST ADJUST Caution: The maintenance/service factory limit setting must not be adjusted to a lower position than the preset factory limit setting. In addition, Draper does not recommend setting show position at the maintenance/service position. Wiring Schematic Up Limit RD Switch NC OR 2 Cond. Cable NC BK BK Down Limit Switch BN NC RD BK Jumper* Delay Switch (ON position) NOTE: This CANNOT be used when lift is installed in Environmental Air Space Housing and Optional Ceiling Closure OR RD UCD BN RD WH BK YL YL/GN RP/RQ Bus Ports for remote controls such as IR Eye, RF Receiver, LED Wall Switch and RS232. BK BK WH OR RD Up Limit Switch NC BK NC RD BK OR Run Cap 60 MFD BK RD Motor Down BK BK BK WH OR RD BL AC Up YL/GN BK AC BK WH COM RD N.O. N.C. OR BK Optional Delay Assembly BK Attached to lower pan 115V ac, 7A 60 Hz Outlet WH WH BK RD WH BK GN N 115V ac, Supply ALTERNATE ‘UP’ LIMIT SWITCH WIRING WH Wall Switch Key Switch Dashed wiring by electrician Low Voltage Trigger (6-24 VDC) Low voltage wiring by others RD BKWH RD WH RD WH BK Encoder www.draperinc.com *Black (BK) Jumper wire is located in the plastic sleeve with these instructions. (765) 987-7999 Scissor Lift SLX by Draper page 7 of 8 Scissor Lift SLX Dimensions Model SLX10 SLX14 SLX17 SLX21 SLX24 SLX28 385/16" (973 mm) 363/16" (919 mm) Table A Closed Extended Height Height 141/16" 10'7" 165/16" 14'2" 189/16" 17'8" 2013/16" 21'3" 231/16" 24'9" 255/16" 28'5" 359/16" (903 mm) 3711/16" (957 mm) Top View See Table A 1 /8" (3.175 mm) 35" (889 mm) 36¼" (921 mm) 391/16" (992 mm) 42" (1067 mm) 357/16" (900 mm) 371/16" (941 mm) 42" (1067 mm) 19/16" (39.6875 mm) Front View Side View Lipless Closure Dimensions 39 1/8" (994mm) x 39 1/8" (994mm) 20¾" 41¾" 41½" 5" 48½"-22½" 19" Front/Back View www.draperinc.com Side View (765) 987-7999 Scissor Lift SLX by Draper page 8 of 8 Installing Optional Environmental Air Space Housing The Environmental Air Space Housing is shipped in pieces, and must be assembled by the installer. The height of the Environmental Air Space Housing is set by drilling out the knockouts at the desired locations then using screws to connect side panels. It is recommended that an access panel be installed in the ceiling to allow future access. The optional Environmental Air Space Housing must be installed per instructions to isolate the lift from the “other space used for environmental air.” Includes trim ring for ceiling opening. 11 11 1 Attach Environmental Air Space Housing top frame to top of Scissor Lift SLX with bolts provided. 2 Install top panel to Environmental Air Space Housing frame. 3 Attach assembly to overhead structure. Allow clearance between Environmental Air Space Housing top and structure for ease of future access. 4 Install side and end panels, and trim frame. Please Note: The factory wiring of 'UP' Limit Switch MUST ALWAYS be used when SLX is installed in Environmental Air Space Housing and Optional Ceiling Closure. See installation instructions included with Environmental Air Space Housing. 11 11 11 7 11 1 11 3 3 11 8 5 4 5 E D SI FRONT /BACK 3 9 Knockouts 6 4 10 Do not use electrical knockouts on bottom sections 2 Item 1 2 3 4 5 6 7 8 9 10 11 Qty Part Number Description 1 C028.544.02SA Frame, SLX Plenum 1 C028.545.07SA Frame, SLX Trim Ring 4 C044.178SA Panel, SLX Plenum Side 4 C044.180SA Panel, SLX Plenum End 2 C044.179SA Panel, SLX Middle End 2 C044.177SA Panel, SLX Plenum Middle Side 1 C095.123SA Cover, SLX Plenum 28 C020.325 Screw, 8-32 x 3/8" Type 1 HWH 40 C018.051 Nut #8-32 Zinc Hex KEPS 12 C013.070 Washer, .188 I.D. x .5 O.D. x .07" TK Nylon Flat 24 C020.112 Screw, 8-32 x 3/8" Type F HWH Caution: Be careful when handling Environmental Air Space Housing Panels. The panels could have sharp edges. www.draperinc.com (765) 987-7999 9 3
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2016:01:15 11:57:35-05:00 Modify Date : 2016:01:15 11:57:39-05:00 Metadata Date : 2016:01:15 11:57:39-05:00 Creator Tool : Adobe InDesign CS6 (Windows) Version ID : 1 Instance ID : uuid:c020fdb1-6210-4e35-9540-464653717fc8 Original Document ID : adobe:docid:indd:63aef111-a651-11df-876b-91833dba2efe Document ID : xmp.id:F4D69A11A9BBE5118E8AB6AE0AD86844 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:F3D69A11A9BBE5118E8AB6AE0AD86844 Derived From Document ID : xmp.did:385C2301FF82E5118A6BE80FF36C5E9A Derived From Original Document ID: adobe:docid:indd:63aef111-a651-11df-876b-91833dba2efe Derived From Version ID : 1 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2016:01:15 11:57:35-05:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 8 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools