Stan's Neo Hub User Manual
User Manual: Stan's-Neo-Hub-User-Manual
Open the PDF directly: View PDF 
.
Page Count: 47
| Download | |
| Open PDF In Browser | View PDF |
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL Technical Manual – Neo & Neo Ultimate Hubs Page 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL Table of Contents 1 1.1 1.2 1.3 1.4 1.5 2 2.1 2.2 3 3.1 3.2 3.2.1 3.2.2 3.2.3 3.3 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 3.4 3.4.1 3.4.2 3.4.3 4 General Target Application Safety Warranty Cleaning Maintenance Intervals Compatibility/Conversion Compatibility/Conversion Charts Bearing Specification and Part Numbers Maintenance Instructions Tools Neo Front End Cap Removal/Replacement Front Hub Bearing Removal Front Hub Bearing Installation Neo Rear End Cap Removal/Replacement Freehub Replacement Rear Hub Bearing Removal Rear Hub Bearing Installation Freehub Pawl & Spring Removal/Installation Freehub Bearing Removal Freehub Bearing Installation Neo OS OS Endcap Removal/Replacement OS Front Hub Bearing Removal OS Front Hub Bearing Installation Hub Diagrams Neo Front Neo Rear Neo Freehubs Page 2 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 1 General 1.1 Target Application This manual contains all applicable information regarding Stan’s NoTubes Neo series hubs. This includes the following: Neo, Neo S, Neo OS, Neo Ultimate, Neo CL, Neo S CL, and Neo Ultimate CL 1.2 Safety Proper assembly maintenance, and installation are necessary for all Stan’s NoTubes Neo hubs and wheels. Incorrect assembly or installation can lead to accidents causing severe injuries or death. 1.3 Warranty All Stan’s NoTubes Neo series hubs are covered by a 3 year warranty against manufacturing defects. Warranty does not cover abuse, misuse, consequential damage resulting from incorrect or nonexistent maintenance, normal wear and tear, and improper installation. Warranties only apply to the original owner with valid sales receipt. If a product is found defective customer will receive, at the discretion of Stan’s NoTubes, free repair or replacement. 1.4 Cleaning The exterior of your Stan’s NoTubes Neo hub should be cleaned regularly to prevent surface abrasions or discoloration which can occur from prolonged contact with acidic soils. A mild detergent is recommended for removal of surface oils and dirt. Further cleaning of the hub internals is outlined in the maintenance sections, respective to each hub model. NOTICE: High-pressure water should NOT be used to clean a Neo hub. This can result in water infiltration past the bearing seals, and will reduce the life of the bearings. O-ring and SealLock seal care: Water and a mild detergent (such as Dawn dish soap) and isopropyl alcohol are recommended to clean the o-rings and end cap seals of Stan’s NoTubes Neo Hubs. Use of harsh chemicals will swell and degrade the o-ring/seal. Page 3 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 1.5 Maintenance Intervals Periodic inspection and cleaning of your Neo hubs will keep them in excellent working condition. When inspecting the hub, make sure there is not excessive play in the wheel and that the bearings roll smooth. If the wheel is loose or the bearings roll rough one or more cartridge bearings may be worn. Check the freehub for smooth rotation and proper engagement. Utilize the Table 1 on the next page, to estimate service intervals for all Stan’s NoTubes Neo hubs: Table 1: Service Intervals for Stan's NoTubes Neo hubs Page 4 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 2 Compatibility/Conversion Stan’s NoTubes Neo hubs are available in multiple axle configurations and can be converted to fit most popular axle standards found on today’s road and mountain bikes. 2.1 Compatibility/Conversion Charts Utilize the tables 2 and 3 on the next pages to determine axle standard compatibility for each Neo hub model. Table 2: Stan’s NoTubes Neo Hub Axle Standard Compatibility/Conversion Chart ● ● ◉ ◉ ◉ ◉ ◉ ● ● ● ● ○ ○ ○ ○ ○ ○ ○ ○ ○ ● ● ● ● ● ● ◉ ◉ Page 5 ○ ○ ○ ● ● ● ○ ○ ● ● ● ● ● Singlespeed ● ● ● ● ● ● ● ◉ SRAM XD ● Campangolo 9/10/11 ● Shimano/SRAM 9/10/11 ● 12x157mm Thru Axle ○ 12x150mm Thru Axle 12x142mm Thru Axle ○ 12x148mm Thru Axle 12x135mm Thru Axle ◉ Freehub 10x135mm Thru Bolt 10x135mm BO 10x135mm QR 10x130mm QR 20x110mm Thru Axle Rear 15x110mm Thru Axle 15x100mm Thru Axle ● ◉ 9x100mm Thru Bolt Neo ◉ ○ ○ Neo OS Neo (Boost) Neo CL ◉ ○ Neo Singlespeed Neo S ◉ ○ ○ Neo S CL ◉ ○ Neo Ultimate ◉ ○ ○ Neo Ultimate (Boost) Neo Ultimate CL ◉ ○ Neo Ultimate Singlespeed ● = Orderable as a Stock Hub Option ◉ = Included with Stock Hub Option ○ = Conversion Parts Available Aftermarket Hub 9x100mm QR 12X100mm Thru Axle Front ● ● ● ● ● ● ● ● ○ ● ○ ○ ● ● ● ● EIS-010 NEO INTERACTIVE HUB SERIES MANUAL Table 3: Stan’s NoTubes Neo Hub End Cap Conversion Charts Neo Neo OS Neo (Boost) Neo CL Neo Singlespeed Neo S Neo S CL Neo Ultimate ZH0780 3 ZH0770 5 ZH0781 ZH0778 ZH0778 ZH0779 ZH0957 4 ZH0780 3 ZH0780 3 ZH0957 4 ZH0780 3 ZH0987 ZH0770 5 ZH0770 5 ZH0770 5 ZH0988 ZH0956 ZH0779 ZH0781 ZH0778 ZH0779 ZH0787 ZH0988 ZH0956 ZH0781 ZH0778 ZH0779 ZH0779 4 ZH0957 ZH0987 3 5 Neo Ultimate Singlespeed ZH0780 ZH0770 ZH0781 Neo Ultimate CL 4 5 = Also available in kit including 135mm QR lever (ZH0769) = Also available in kit including 135mm QR lever (ZH0962) = Kit includes axle, end caps and bolts Page 6 ZH0988 ZH0778 12x157mm Thru Axle 12x150mm Thru Axle ZH0779 Neo Ultimate (Boost) 3 12x148mm Thru Axle 12x142mm Thru Axle 12x135mm Thru Axle 10x135mm Thru Bolt 10x135mm BO 10x135mm QR Rear Hub End Cap Kit Part Numbers ZH0956 ZH0779 ZH0779 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 2.2 Bearing Specification and Part Numbers Use Table 4 below to find the proper bearing size and quantity for your hub and Table 5 to find the corresponding part number for what you need. Stan’s NoTubes offers two grades of bearing: chrome steel (stock in Neo, Neo OS, and Neo CL) and stainless steel (stock in Neo S, Neo Ultimate, and Neo Ultimate CL) - they are interchangeable. Table 4: Bearing Size and Quantity for Neo Series Hubs Neo Neo OS Neo CL Neo Singlespeed Neo S Neo S CL Neo Ultimate Neo Ultimate CL Neo Ultimate Singlespeed Front* 6902 (x2) 6804 (x2) 6902 (x2) 6902 (x2) 6902 (x2) 6902 (x2) 6902 (x2) Rear 6902 (x2) 6902 (x2) 6902 (x2) 6902 (x2) 6902 (x2) 6902 (x2) 6902 (x2) 6902 (x2) 6902 (x2) Table 5: NoTubes Bearing Part Numbers* Freehub** 15267 (x2) 15267 (x2) 15267 (x2) 15267 (x2) 15267 (x2) 15267 (x2) 15267 (x2) 15267 (x2) 15267 (x2) * = While Notubes bearings are a standard size, they feature a machined groove to aid in axle sleeve location and must be used in Neo series front hubs (see section 3.2.3 for further detail) ** = All Neo series freehubs use the same bearings Page 7 6902 6804 6900 15267 Chrome Steel ZH0816 ZH0818 ZH0958 ZH0814 Stainless Steel ZH0817 ZH0819 ZH0959 ZH0815 * = All NoTubes bearings are sold in pairs. EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 3 Maintenance Instructions This chapter contains detailed instructions for servicing a Stan’s NoTubes Neo hub. This includes end cap removal, axle and bearing removal, freehub service, as well as reassembly of the hub. Careful adherence to these instructions is necessary to safely and reliably service a Neo hub. 3.1 Tools Stan’s NoTubes Neo series hubs are designed to be user-friendly and require a bare minimum of tools to service. Below is a list of what is needed to perform a complete service on a pair of Neo hubs: ● ● ● ● ● ● ● ● ● ● ● ● ● Bench Vise Clean, lint free rags Dumonde Tech Freehub Grease (or similar light-weight grease) Park Tool AV-5 Aluminum Axle Vise Insert 15mm Sealed Bearing Extractor (such as Wheels Manufacturing 15mm Sealed Bearing Extractor), and necessary tools ¼” or ⅜”, or similar, Punch Hammer Soft-Faced Mallet Bearing Press (such as Wheels Manufacturing Press-1) with necessary installation drifts A small flathead screwdriver Isopropyl Alcohol Toothbrush Clean rag Page 8 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 3.2 Neo Front Hubs Before performing maintenance service on a Stan’s NoTubes Neo hub, clean the exterior of the hub in accordance with Section 1.4. 3.2.1 End Cap Removal/Replacement 1. Remove end caps: ● For Quick Release End caps: Clamp one end cap in the 20mm slot of the Park Tool AV-5. Gently oscillate the hub/wheel while lightly pulling upwards to unseat the cap. Repeat on the other end cap. For 15mm End cap: Clamp one end cap in the 20mm slot of the Park Tool AV-5. Gently rock the hub/wheel toward you to unseat the cap. Repeat on the other end cap. Page 9 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 2. Clean end caps before reinserting into the hub. (Note: Cleansing of the end cap seals should be performed in accordance with Section 1.5 to prevent damaging them). Ensure that the SealLock seals are positioned with their U-hook facing outwards from the hub body, as shown below. Install end caps, taking care to not pinch or fold the SealLock seal 3.2.2 Front Hub Bearing Removal 1. Remove end caps from hub using the procedures found in Step 1 of “End Cap Removal/Replacement 2. Insert 15mm Sealed Bearing Extractor into bearing and tighten with an open-end wrench. Tap the extractor and bearing out of the hub shell using a hammer and punch. (Note: Perform this step over a rag as the bearing, extractor, and inner axle sleeve will fall from the hub shell when the bearing is removed.) 3. Remove the inner axle sleeve. 4. Repeat step 2 to remove second bearing. Page 10 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 3.2.3 Front Hub Bearing Installation 1. Thoroughly clean hub shell bore, hub sleeve, and bearing exteriors with isopropyl alcohol and a clean rag. 2. Apply thin layer of grease to the non-drive side bearing bore and the outer race of the bearing. 3. Arrange the hub shell, bearing press, a 6902 open bore drift, and one 6902 bearing as shown below. (Note: Installing one bearing at a time ensures the bearing is installed straight). 4. Turn the handle clockwise to press the bearing into the hub until it is hand-tight and the bearing is fully seated in the hub shell (Note: Overtightening can result in bearing damage). 5. Apply thin layer of grease to the drive side bearing bore and the outer race of the bearing. 6. With the hub axis oriented vertically, insert the inner axle sleeve. Note: The axle sleeve has a lip on one end. Insert axle sleeve lip-side down to locate in the groove on the bearing’s inner race. (Continued on next) Page 11 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 7. Arrange the hub, bearing press, bearing drifts, and one 6902 bearing as shown below. (Note: It is very important to keep the hub vertical and steady for this step. If the sleeve dislocates, it may damage the lips of the axle sleeve upon installation of the second bearing). 8. Turn the handle clockwise to press the bearing into the hub until it is hand-tight and the bearing is fully seated in the hub shell (Note: overtightening can result in bearing damage). Page 12 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 3.3 Neo Rear Hubs Before performing maintenance service on a Stan’s NoTubes Neo hub, clean the exterior of the hub in accordance with Section 1.4. 3.3.1 General Maintenance Disassembly 1. Remove end caps: Remove non-drive (disc side) endcap. Neo series endcaps are designed to be removed by hand. Should the endcap not come off easily (this is common with a brand-new, never disassembled hub) an axle vise may be needed. Page 13 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL Remove axle and drive-side endcap by hand. If the axle will not remove by hand, tap on the exposed (non-drive) axle end with a soft-face hammer to dislodge. 2. Pull the freehub from the hub shell. Take care not to lose the small red spacer which sits between the freehub body and the drive-side bearing. 3. Using a small flathead screw driver, gently remove the co-molded freehub seal from the hub shell. Take care not to cut or pinch the edge of the seal. 3.3.2 General Maintenance Reassembly 1. Clean the drive ring, co-molded freehub seal, and freehub using isopropyl alcohol and a clean toothbrush. Apply a light coating of Dumonde Tech Freehub Grease to the axle, drive ring, and freehub pawls. 2. Install co-molded freehub seal into the groove adjacent to the drive ring in the hub shell. 3. Insert axle into hub. 4. Slide red spacer onto axle. Page 14 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 5. Install freehub by sliding onto the axle and twisting counter-clockwise to allow the freehub pawls to mesh with the drive ring. Take care not to cut the co-molded freehub seal. 6. Clean end caps with isopropyl alcohol, a toothbrush, and a clean rag. 7. Gently press end caps onto axle by hand (the flanged end cap goes on the non-drive side) . Take care not to pinch the o-ring inside each end cap as well as the v-seal on the non-drive side end cap Page 15 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 3.3.3 Rear Hub Bearing Removal 1. Disassemble hub by methods outlined in section 3.3.1 General Maintenance Disassembly. 2. Install 15mm Sealed Bearing Extractor into one of the bearings. Tap Extractor and bearing out of hub shell using punch and hammer, as shown in below. (Note: Perform this step over a rag as the bearing, extractor, and inner axle sleeve will fall from the hub shell when the bearing is removed. 3. Repeat step 2 to remove second bearing. 3.3.4 Rear Hub Bearing Installation 1. Thoroughly clean hub shell bore, hub sleeve, and bearing exteriors with isopropyl alcohol and a clean rag. 2. Apply thin layer of grease to the non-drive side bearing bore. 3. Arrange the hub shell, bearing press, a pair of 6902 open bore drifts, and one 6902 bearing as shown below. (Note: Installing one bearing at a time ensures the bearing is installed straight) Page 16 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 4. Turn the handle clockwise to press the bearing into the hub until it is hand-tight and the bearing is fully seated in the hub shell. Note: Over-tightening can result in bearing damage. 5. Insert inner axle sleeve. 6. Arrange the hub shell, bearing press, drifts, and the second 6902 bearing as shown below. 7. Turn the handle clockwise to press the bearing into the hub until it is hand-tight and the bearing is fully seated in the hub shell. (Note: Over-tightening can result in bearing damage.) 3.3.5 Freehub Pawl & Spring Removal/Installation 1. Using a small flathead screw driver, pry the pawl retaining ring off of the freehub body. 2. Slide the pawls, and then pawl springs, out of their respective pockets in the freehub body. 3. Thoroughly clean the pawls, pawls springs, and pawl pockets in the freehub body with isopropyl alcohol, a toothbrush, and a clean rag. Page 17 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 4. Reassemble the freehub by first installing the pawl springs, and then the pawls. See below for proper arrangement. (Note: In order to ensure proper freehub function, take care not to deform pawl springs during installation.) 5. Install the pawl retaining ring into its groove in the freehub body. Insert photo showing pawl retaining ring install. 3.3.6 Freehub Bearing Removal 1. Remove the pawl retaining ring, pawls, and pawl springs from the freehub body by methods outlined in Section 3.3.5 Freehub Pawl & Spring Removal/Installation. 2. Remove the rubber seal adjacent to the outboard bearing with a small flathead screwdriver Page 18 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 3. Insert 15mm Sealed Bearing Extractor into one of the freehub bearings. Tap Extractor and bearing out of hub shell using punch and hammer, as shown in the following image. (Note: Perform this step over a rag as the bearing, extractor, and inner axle sleeve will fall from the hub shell when the bearing is removed.) 4. Install 15mm Sealed Bearing Extractor in the second bearing. Tap Extractor and bearing out of hub shell using punch and hammer. 3.3.7 Freehub Bearing Installation 1. Thoroughly clean freehub body bore, freehub sleeve, and bearing exteriors with isopropyl alcohol and a clean rag. 2. Apply thin layer of grease to the outboard bearing bore. 3. Arrange the freehub body, bearing press, 15267 open bore drifts, and one 15267 bearing as shown below. (Note: Installing one bearing at a time ensures the bearing is installed straight). Page 19 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 4. Turn the handle clockwise to press the bearing into the hub until it is hand-tight and the bearing is fully seated in the hub shell. (Note: Over-tightening can result in bearing damage.) 5. Apply thin layer of grease to the inboard bearing bore. 6. Insert inner axle sleeve. 7. Arrange the freehub, bearing press, drifts, and the second 15267 bearing as shown below: 8. Turn the handle counter-clockwise to press the bearing into the hub until it is hand-tight and the bearing is fully seated in the hub shell. (Note: Over-tightening can result in bearing damage.) Note: Small grooves and burrs from the cassette's contact with the freehub will not affect hub performance, and can be gently filed down to allow easier cassette installation. (Note: Only light filing is needed; take care not to remove more material than necessary.) Page 20 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 3.4 Front OS Hubs Before performing maintenance service on a Stan’s NoTubes Neo hub, clean the exterior of the hub in accordance with Section 1.4. Additional Tools Required: ● 20mm Sealed Bearing Extractor, and necessary tools 3.4.1 OS End Cap Removal/Replacement 3. Remove end caps: ● For Quick Release End caps: Clamp one end cap in the 20mm slot of the Park Tool AV-5. Oscillate the hub/wheel while lightly pulling upwards to unseat the cap. Repeat on the other end cap. ● For 15mm End caps: Clamp one end cap in the 20mm slot of the Park Tool AV-5. Oscillate the hub/wheel while lightly pulling upwards to unseat the cap. Repeat on the other end cap. ● For 20mm End cap: Clamp one end cap in the 25mm slot of the Park Tool AV-5. Gently rock the hub/wheel toward you to unseat the cap. Repeat on the other end cap. 4. Clean end caps before reinserting into the hub. Note: Cleansing of the end cap seals should be performed in accordance with Section 1.5 to prevent damaging them. Ensure that the SealLock seals are positioned with their U-hook facing outwards from the hub body, as shown below. 5. To reinstall, press end caps in by hand. (Note: Take care to not pinch or fold the SealLock seal.) Page 21 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 3.4.2 OS Front Hub Bearing Removal 1. Remove end caps from hub using the procedures found in Step 1 of “End Cap Removal/Replacement” 2. Install 20mm Sealed Bearing Extractor into one of the bearings. Tap Extractor and bearing out of hub shell using punch and hammer, as shown below. (Note: Perform this step over a rag as the bearing, extractor, and inner axle sleeve will fall from the hub shell when the bearing is removed.) 3. Repeat step 2 to remove second bearing. Page 22 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 3.4.3 OS Front Hub Bearing Installation 1. Thoroughly clean hub shell bore, hub sleeve, and bearing exteriors with isopropyl alcohol and a clean rag. 2. Apply thin layer of grease to the non-drive side bearing bore. 3. Arrange the hub shell, bearing press, a 6804 open bore drift, and one 6804 bearing as shown below. (Note: Installing one bearing at a time ensures the bearing is installed straight). 4. Turn the handle clockwise to press the bearing into the hub until it is hand-tight and the bearing is fully seated in the hub shell (note: overtightening can result in bearing damage). 5. Apply thin layer of grease to the drive side bearing bore and the outer race of the bearing. 6. With the hub axis oriented vertically, insert the inner axle sleeve. Note: The axle sleeve has a lip on each end which aligns it with the inner bearing races. (Continued on next) Page 23 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL 7. Arrange the hub, bearing press, bearing drifts, and the second 6804 bearing as shown below. Note: Hold the hub steady to maintain the centralized location of the inner axle sleeve. If the sleeve dislocates, it may damage the lips of the axle sleeve upon installation of the second bearing. 8. Turn the handle clockwise to press the bearing into the hub until it is hand-tight and the bearing is fully seated in the hub shell (Note: overtightening can result in bearing damage). Page 24 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL FLANGE (mm) CTR TO FLANGE (mm) LEFT(DISC) RIGHT(DRIVE) 55.5 55.5 21.5 33.5 B B 1 3 A # 1 * * * * 2 3 * ** 2 KIT # KIT DESCRIPTION KIT CONTENTS ZH0771 KIT, NEO, END CAPS, FRONT, 15MM TA E01 ZH0772 KIT, NEO, END CAPS, FRONT, 9MM QR E04 ZH0773 KIT, NEO, END CAPS, FRONT, 9MM TA E03 ZH0774 KIT, NEO, END CAPS, FRONT, 12MM TA E02 ZH0985 KIT, NEO, END CAPS, FRONT, TORQUE CAP E28 ZH0792 KIT, NEO, AXLE SPACER, FRONT, 15/9X100, STD S09 ZH0817 KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC ZH0816 KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC ZH0813 KIT, NEO, END CAP SEALS, FRONT AND REAR * denotes optional hub configuration **includes seals for all configurations 2 3 1 A HUB, FRONT, STANS, NEO, 6B, 15X100, TA Page 25 1 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL FLANGE (mm) CTR TO FLANGE (mm) LEFT(DISC) RIGHT(DRIVE) 55.5 44.5 28 40.5 B B 1 3 2 3 A # 1 * * * * 2 3 * ** KIT # KIT DESCRIPTION KIT CONTENTS ZH0771 KIT, NEO, END CAPS, FRONT, 15MM TA E01 ZH0772 KIT, NEO, END CAPS, FRONT, 9MM QR E04 ZH0773 KIT, NEO, END CAPS, FRONT, 9MM TA E03 ZH0774 KIT, NEO, END CAPS, FRONT, 12MM TA E02 ZH0985 KIT, NEO, END CAPS, FRONT, TORQUE CAP E28 ZH0794 KIT, NEO, AXLE SPACER, FRONT, 15X110, STD S11 ZH0817 KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC ZH0816 KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC ZH0813 KIT, NEO, END CAP SEALS, FRONT AND REAR * denotes optional hub configuration **includes seals for all configurations 2 1 A HUB, FRONT, STANS, NEO, 6B, 15X110, TA Page 26 1 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL FLANGE (mm) CTR TO FLANGE (mm) LEFT(DISC) RIGHT(DRIVE) 55.5 55.5 21.5 33.5 B B 1 3 2 3 A # 1 * * * 2 3 * ** A KIT # KIT DESCRIPTION KIT CONTENTS ZH0953 KIT, NEO, END CAPS, FRONT, 15MM TA, CL E20 ZH0954 KIT, NEO, END CAPS, FRONT, 9MM QR, CL E21 ZH0986 KIT, NEO, END CAPS, FRONT, 9MM TA, CL E26 ZH0955 KIT, NEO, END CAPS, FRONT, 12MM TA, CL E22 ZH0991 KIT, NEO, AXLE SPACER, FRONT, 15X110, STD, CL S17 ZH0817 KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC ZH0816 KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC ZH0813 KIT, NEO, END CAP SEALS, FRONT AND REAR * denotes optional hub configuration **includes seals for all configurations 2 1 HUB, FRONT, STANS, NEO, CL, 15X100, TA Page 27 1 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL FLANGE (mm) CTR TO FLANGE (mm) LEFT(DISC) RIGHT(DRIVE) 55.5 45.5 22.0 35.5 B B 1 3 2 3 A # 1 * * * * 2 3 ** A KIT # KIT DESCRIPTION KIT CONTENTS ZH0771 KIT, NEO, END CAPS, FRONT, 15MM TA E01 ZH0772 KIT, NEO, END CAPS, FRONT, 9MM QR E04 ZH0773 KIT, NEO, END CAPS, FRONT, 9MM TA E03 ZH0774 KIT, NEO, END CAPS, FRONT, 12MM TA E02 ZH0985 KIT, NEO, END CAPS, FRONT, TORQUE CAP E28 ZH0793 KIT, NEO, AXLE SPACER, FRONT, 15/9X100, LTE S10 ZH0817 KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC ZH0813 KIT, NEO, END CAP SEALS, FRONT AND REAR * denotes optional hub configuration **includes seals for all configurations 2 1 HUB, FRONT, STANS, NEO ULT, 6B, 15X100, TA Page 28 1 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL FLANGE (mm) CTR TO FLANGE (mm) LEFT(DISC) RIGHT(DRIVE) 55.5 45.5 28 40.5 B B 1 3 2 3 A # 1 * * * * 2 3 ** A KIT # KIT DESCRIPTION KIT CONTENTS ZH0771 KIT, NEO, END CAPS, FRONT, 15MM TA E01 ZH0772 KIT, NEO, END CAPS, FRONT, 9MM QR E04 ZH0773 KIT, NEO, END CAPS, FRONT, 9MM TA E03 ZH0774 KIT, NEO, END CAPS, FRONT, 12MM TA E02 ZH0985 KIT, NEO, END CAPS, FRONT, TORQUE CAP E28 ZH0795 KIT, NEO, AXLE SPACER, FRONT, 15X110, LTE S12 ZH0817 KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC ZH0813 KIT, NEO, END CAP SEALS, FRONT AND REAR * denotes optional hub configuration **includes seals for all configurations 2 1 HUB, FRONT, STANS, NEO ULT, 6B, 15X110, TA Page 29 1 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL FLANGE (mm) CTR TO FLANGE (mm) LEFT(DISC) RIGHT(DRIVE) 55.5 45.5 22.0 35.5 B B 1 3 2 3 A # 1 * * * 2 3 ** A KIT # KIT DESCRIPTION KIT CONTENTS ZH0953 KIT, NEO, END CAPS, FRONT, 15MM TA, CL E20 ZH0954 KIT, NEO, END CAPS, FRONT, 9MM QR, CL E21 ZH0986 KIT, NEO, END CAPS, FRONT, 9MM TA, CL E26 ZH0955 KIT, NEO, END CAPS, FRONT, 12MM TA, CL E22 ZH0989 KIT, NEO, AXLE SPACER, FRONT, 15X110, LTE, CL S18 ZH0817 KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC ZH0813 KIT, NEO, END CAP SEALS, FRONT AND REAR * denotes optional hub configuration **includes seals for all configurations 2 1 HUB, FRONT, STANS, NEO ULTIMATE, CL, 15X100, TA Page 30 1 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL (mm) FLANGE CTR TO FLANGE (mm) LEFT(DISC) RIGHT(DRIVE) 55.5 55.5 27.5 38.5 B B 1 3 2 3 A # 1 * * * * * 2 KIT # ZH0776 ZH0777 ZH0983 ZH0775 ZH0984 ZH0982 ZH0990 KIT DESCRIPTION KIT, NEO OS, END CAPS, FRONT, 15MM TA KIT, NEO OS, END CAPS, FRONT, 9MM QR KIT, NEO OS, END CAPS, FRONT, 12MM TA KIT, NEO OS, END CAPS, FRONT, 20MM TA KIT, NEO OS, END CAPS, FRONT, TORQUE CAP KIT, NEO OS, END CAPS, FRONT, 9MM TA KIT, NEO OS, AXLE SPACER, FRONT, 15X110, STD 3 ZH0818 KIT, BEARING, #6804, 20X32X7MM, CHROME (GRAY) 2PC ** ZH0813 KIT, NEO, END CAP SEALS, FRONT AND REAR * denotes optional hub configuration **includes seals for all configurations 2 1 KIT CONTENTS E06 E07 E25 E05 E29 E24 S16 A HUB, FRONT, STANS, NEO, 6B, 15X110, OS, TA Page 31 1 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL (mm) FLANGE CTR TO FLANGE (mm) LEFT(DISC) RIGHT(DRIVE) 55.5 55.5 34.5 18.5 1 B B 3 4 1 5 6 2 A # 1 * * * * * 2 3 * 4 * 5 * 6 ** ** KIT # ZH0779 ZH0778 ZH0780 ZH0781 ZH0769 ZH0770 ZH0782 ZH0786 ZH0787 ZH0805 ZH0806 ZH0816 ZH0817 ZH0802 ZH0813 ZH0799 KIT DESCRIPTION KIT, NEO, END CAPS, REAR, 12X142/148/157 TA KIT, NEO, END CAPS, REAR, 12X135/150 TA KIT, NEO, END CAPS, REAR, 10X135 QR KIT, NEO, END CAPS, REAR, 10X135 TA KIT, NEO, CONVERSION, REAR, QR END CAPS AND 135MM LEVER KIT, NEO, CONVERSION, REAR, BO END CAPS, AXLE, AND BOLTS KIT, NEO, AXLE, REAR, 12X135/142 & SINGLESPEED KIT, NEO, AXLE SPACER, REAR, 12X135/142 , STD KIT, NEO, AXLE SPACER, REAR, 12X135/142 , LTE KIT, NEO, FREEHUB, 4-PAWL, SHIMANO (BLACK) KIT, NEO, FREEHUB, 4-PAWL, SRAM XD (BLACK) KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC KIT, NEO, CASSETTE SPACER, 10SP (SILVER) KIT, NEO, END CAP SEALS, FRONT AND REAR KIT, NEO, FREEHUB SEALS * denotes optional hub configuration **includes seals for all configurations 2 KIT CONTENTS E15,E16 E13,E14 E11,E12 E09,E10 E11,E12 A01 S01 S02 - 5 4 A HUB, REAR, STANS, NEO, 6B, 12x142, TA Page 32 1 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL (mm) FLANGE CTR TO FLANGE (mm) B LEFT(DISC) RIGHT(DRIVE) 55.5 55.5 37.5 23.0 B 5 3 5 4 1 4 6 2 A # 1 * * * 2 3 4 * * 5 * 6 ** ** KIT # ZH0779 ZH0778 ZH0780 ZH0781 ZH0783 ZH0788 ZH0805 ZH0806 ZH0808 ZH0816 ZH0817 ZH0802 ZH0813 ZH0799 KIT DESCRIPTION KIT, NEO, END CAPS, REAR, 12X142/148/157 TA KIT, NEO, END CAPS, REAR, 12X135/150 TA KIT, NEO, END CAPS, REAR, 10X135 QR KIT, NEO, END CAPS, REAR, 10X135 TA KIT, NEO, AXLE, REAR, 12X148 KIT, NEO, AXLE SPACER, REAR, 12X148, STD KIT, NEO, FREEHUB, 4-PAWL, SHIMANO (BLACK) KIT, NEO, FREEHUB, 4-PAWL, SRAM XD (BLACK) KIT, NEO, FREEHUB, 4-PAWL, CAMPY (BLACK) KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC KIT, NEO, CASSETTE SPACER, 10SP (SILVER) KIT, NEO, END CAP SEALS, FRONT AND REAR KIT, NEO, FREEHUB SEALS * denotes optional hub configuration **includes seals for all configurations 2 KIT CONTENTS E15,E16 E13,E14 E11,E12 E09,E10 A02 S03 1 HUB, REAR, STANS, NEO, 6B, 12x148, TA Page 33 1 A 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL LEFT(DISC) RIGHT(DRIVE) 55.5 55.5 42.0 26.0 (mm) FLANGE CTR TO FLANGE (mm) B B 5 3 5 4 4 1 6 2 A # 1 * * 2 3 4 * * 5 * 6 ** ** KIT # ZH0779 ZH0778 ZH0781 ZH0784 ZH0790 ZH0805 ZH0806 ZH0808 ZH0816 ZH0817 ZH0802 ZH0813 ZH0799 KIT DESCRIPTION KIT, NEO, END CAPS, REAR, 12X142/148/157 TA KIT, NEO, END CAPS, REAR, 12X135/150 TA KIT, NEO, END CAPS, REAR, 10X135 TA KIT, NEO, AXLE, REAR, 12X150/157 KIT, NEO, AXLE SPACER, REAR, 12X150/157 & SINGLESPEED, STD KIT, NEO, FREEHUB, 4-PAWL, SHIMANO (BLACK) KIT, NEO, FREEHUB, 4-PAWL, SRAM XD (BLACK) KIT, NEO, FREEHUB, 4-PAWL, CAMPY (BLACK) KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC KIT, NEO, CASSETTE SPACER, 10SP (SILVER) KIT, NEO, END CAP SEALS, FRONT AND REAR KIT, NEO, FREEHUB SEALS * denotes optional hub configuration **includes seals for all configurations 2 KIT CONTENTS E15,E16 E13,E14 E09,E10 A03 S05 1 HUB, REAR, STANS, NEO, 6B, 12x157, TA Page 34 1 A 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL (mm) FLANGE CTR TO FLANGE (mm) B LEFT(DISC) RIGHT(DRIVE) 55.5 55.5 34.5 33.5 B 5 3 5 4 4 1 2 A # 1 * * * * * 2 3 4 5 * * ** ** KIT # ZH0779 ZH0778 ZH0780 ZH0781 ZH0769 ZH0770 ZH0782 ZH0790 ZH0807 ZH0816 ZH0817 ZH0804 ZH0813 ZH0799 KIT DESCRIPTION KIT, NEO, END CAPS, REAR, 12X142/148/157 TA KIT, NEO, END CAPS, REAR, 12X135/150 TA KIT, NEO, END CAPS, REAR, 10X135 QR KIT, NEO, END CAPS, REAR, 10X135 TA KIT, NEO, CONVERSION, REAR, QR END CAPS AND 135MM LEVER KIT, NEO, CONVERSION, REAR, BO END CAPS, AXLE, AND BOLTS KIT, NEO, AXLE, REAR, 12X135/142 & SINGLESPEED KIT, NEO, AXLE SPACER, REAR, 12X150/157 & SINGLESPEED, STD KIT, NEO, FREEHUB, 4-PAWL, SINGLESPEED (BLACK) KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC KIT, NEO, SINGLESPEED SPACER KIT KIT, NEO, END CAP SEALS, FRONT AND REAR KIT, NEO, FREEHUB SEALS * denotes optional hub configuration **includes seals for all configurations 2 KIT CONTENTS E15,E16 E13,E14 E11,E12 E09,E10 E11,E12 1 A A01 S05 HUB, REAR, STANS, NEO, 6B, 12x142, TA, SS Page 35 1 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL (mm) FLANGE CTR TO FLANGE (mm) B LEFT(DISC) RIGHT(DRIVE) 55.5 55.5 33.5 18.5 B 5 3 5 4 1 4 6 2 A # 1 * * * * * 2 3 4 * * 5 * 6 ** ** KIT # KIT DESCRIPTION KIT CONTENTS ZH0956 KIT, NEO, END CAPS, REAR, 12X142/148/157 TA, CL E19,E16 ZH0988 KIT, NEO, END CAPS, REAR, 12X135/150 TA, CL E18,E14 ZH0957 KIT, NEO, END CAPS, REAR, 10X135 QR, CL E17,E12 ZH0987 KIT, NEO, END CAPS, REAR, 10X135 TA, CL E27,E10 ZH0962 KIT, NEO, CONVERSION, REAR, QR END CAPS AND 135MM LEVER, CL E17,E12 ZH0770 KIT, NEO, CONVERSION, REAR, BO END CAPS, AXLE, AND BOLTS ZH0782 KIT, NEO, AXLE, REAR, 12X135/142 & SINGLESPEED A01 ZH0995 KIT, NEO, AXLE SPACER, REAR, 12X135/142 , STD, CL S21 ZH0805 KIT, NEO, FREEHUB, 4-PAWL, SHIMANO (BLACK) ZH0806 KIT, NEO, FREEHUB, 4-PAWL, SRAM XD (BLACK) ZH0808 KIT, NEO, FREEHUB, 4-PAWL, CAMPY (BLACK) ZH0816 KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC ZH0817 KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC ZH0802 KIT, NEO, CASSETTE SPACER, 10SP (SILVER) ZH0813 KIT, NEO, END CAP SEALS, FRONT AND REAR ZH0799 KIT, NEO, FREEHUB SEALS * denotes optional hub configuration **includes seals for all configurations 2 Page 36 1 A HUB, REAR, STANS, NEO, CL, 12x142, TA 1 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL (mm) FLANGE CTR TO FLANGE (mm) B LEFT(DISC) RIGHT(DRIVE) 55.5 55.5 33.5 18.5 B 5 3 5 4 4 6 1 2 A # 1 * * * * * 2 3 4 * * 5 6 ** ** KIT # ZH0779 ZH0778 ZH0780 ZH0781 ZH0769 ZH0770 ZH0782 ZH0787 ZH0809 ZH0810 ZH0812 ZH0817 ZH0802 ZH0813 ZH0799 KIT DESCRIPTION KIT, NEO, END CAPS, REAR, 12X142/148/157 TA KIT, NEO, END CAPS, REAR, 12X135/150 TA KIT, NEO, END CAPS, REAR, 10X135 QR KIT, NEO, END CAPS, REAR, 10X135 TA KIT, NEO, CONVERSION, REAR, QR END CAPS AND 135MM LEVER KIT, NEO, CONVERSION, REAR, BO END CAPS, AXLE, AND BOLTS KIT, NEO, AXLE, REAR, 12X135/142 & SINGLESPEED KIT, NEO, AXLE SPACER, REAR, 12X135/142 , LTE KIT, NEO, FREEHUB, 6-PAWL, SHIMANO (GRAY) KIT, NEO, FREEHUB, 6-PAWL, SRAM XD (GRAY) KIT, NEO, FREEHUB, 6-PAWL, CAMPY (GRAY) KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC KIT, NEO, CASSETTE SPACER, 10SP (SILVER) KIT, NEO, END CAP SEALS, FRONT AND REAR KIT, NEO, FREEHUB SEALS * denotes optional hub configuration **includes seals for all configurations 2 KIT CONTENTS E15,E16 E13,E14 E11,E12 E09,E10 E11,E12 1 A A01 S02 HUB, REAR, STANS, NEO ULT, 6B, 12x142, TA Page 37 1 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL (mm) FLANGE CTR TO FLANGE (mm) B LEFT(DISC) RIGHT(DRIVE) 55.5 55.5 37.5 23.0 B 5 3 5 4 4 6 1 2 A # 1 * * * 2 3 4 * * 5 6 ** ** KIT # ZH0779 ZH0778 ZH0780 ZH0781 ZH0783 ZH0789 ZH0809 ZH0810 ZH0812 ZH0817 ZH0802 ZH0813 ZH0799 KIT DESCRIPTION KIT, NEO, END CAPS, REAR, 12X142/148/157 TA KIT, NEO, END CAPS, REAR, 12X135/150 TA KIT, NEO, END CAPS, REAR, 10X135 QR KIT, NEO, END CAPS, REAR, 10X135 TA KIT, NEO, AXLE, REAR, 12X148 KIT, NEO, AXLE SPACER, REAR, 12X148, LTE KIT, NEO, FREEHUB, 6-PAWL, SHIMANO (GRAY) KIT, NEO, FREEHUB, 6-PAWL, SRAM XD (GRAY) KIT, NEO, FREEHUB, 6-PAWL, CAMPY (GRAY) KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC KIT, NEO, CASSETTE SPACER, 10SP (SILVER) KIT, NEO, END CAP SEALS, FRONT AND REAR KIT, NEO, FREEHUB SEALS * denotes optional hub configuration **includes seals for all configurations 2 KIT CONTENTS E15,E16 E13,E14 E11,E12 E09,E10 A02 S04 1 A HUB, REAR, STANS, NEO ULT, 6B, 12x148, TA Page 38 1 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL (mm) FLANGE CTR TO FLANGE (mm) B LEFT(DISC) RIGHT(DRIVE) 55.5 55.5 42.0 26.0 B 5 3 5 4 4 6 1 2 A # 1 * * 2 3 4 * * 5 6 ** ** KIT # ZH0779 ZH0778 ZH0781 ZH0784 ZH0992 ZH0809 ZH0810 ZH0812 ZH0817 ZH0802 ZH0813 ZH0799 KIT DESCRIPTION KIT, NEO, END CAPS, REAR, 12X142/148/157 TA KIT, NEO, END CAPS, REAR, 12X135/150 TA KIT, NEO, END CAPS, REAR, 10X135 TA KIT, NEO, AXLE, REAR, 12X150/157 KIT, NEO, AXLE SPACER, REAR, 12X150/157 & SINGLESPEED, LTE KIT, NEO, FREEHUB, 6-PAWL, SHIMANO (GRAY) KIT, NEO, FREEHUB, 6-PAWL, SRAM XD (GRAY) KIT, NEO, FREEHUB, 6-PAWL, CAMPY (GRAY) KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC KIT, NEO, CASSETTE SPACER, 10SP (SILVER) KIT, NEO, END CAP SEALS, FRONT AND REAR KIT, NEO, FREEHUB SEALS * denotes optional hub configuration **includes seals for all configurations 2 KIT CONTENTS E15,E16 E13,E14 E09,E10 A03 S06 1 HUB, REAR, STANS, NEO ULT, 6B, 12x157, TA Page 39 1 A 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL (mm) FLANGE CTR TO FLANGE (mm) B LEFT(DISC) RIGHT(DRIVE) 55.5 55.5 34.5 33.5 B 5 3 5 4 4 1 2 A # 1 * * * * * 2 3 4 5 * ** ** KIT # ZH0779 ZH0778 ZH0780 ZH0781 ZH0769 ZH0770 ZH0782 ZH0992 ZH0811 ZH0817 ZH0804 ZH0813 ZH0799 KIT DESCRIPTION KIT, NEO, END CAPS, REAR, 12X142/148/157 TA KIT, NEO, END CAPS, REAR, 12X135/150 TA KIT, NEO, END CAPS, REAR, 10X135 QR KIT, NEO, END CAPS, REAR, 10X135 TA KIT, NEO, CONVERSION, REAR, QR END CAPS AND 135MM LEVER KIT, NEO, CONVERSION, REAR, BO END CAPS, AXLE, AND BOLTS KIT, NEO, AXLE, REAR, 12X135/142 & SINGLESPEED KIT, NEO, AXLE SPACER, REAR, 12X150/157 & SINGLESPEED, LTE KIT, NEO, FREEHUB, 6-PAWL, SINGLESPEED (GRAY) KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC KIT, NEO, SINGLESPEED SPACER KIT KIT, NEO, END CAP SEALS, FRONT AND REAR KIT, NEO, FREEHUB SEALS * denotes optional hub configuration **includes seals for all configurations 2 KIT CONTENTS E15,E16 E13,E14 E11,E12 E09,E10 E11,E12 1 A01 S06 HUB, REAR, STANS, NEO ULT, 6B, 12x142, TA, SS Page 40 1 A 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL (mm) FLANGE CTR TO FLANGE (mm) B LEFT(DISC) RIGHT(DRIVE) 55.5 55.5 33.5 18.5 B 5 3 5 4 4 1 6 2 A # 1 * * * * * 2 3 4 * * 5 6 ** ** KIT # KIT DESCRIPTION KIT CONTENTS ZH0956 KIT, NEO, END CAPS, REAR, 12X142/148/157 TA, CL E19,E16 ZH0988 KIT, NEO, END CAPS, REAR, 12X135/150 TA, CL E18,E14 ZH0957 KIT, NEO, END CAPS, REAR, 10X135 QR, CL E17,E12 ZH0987 KIT, NEO, END CAPS, REAR, 10X135 TA, CL E27,E10 ZH0962 KIT, NEO, CONVERSION, REAR, QR END CAPS AND 135MM LEVER, CL E17,E12 ZH0770 KIT, NEO, CONVERSION, REAR, BO END CAPS, AXLE, AND BOLTS ZH0782 KIT, NEO, AXLE, REAR, 12X135/142 & SINGLESPEED A01 ZH0994 KIT, NEO, AXLE SPACER, REAR, 12X135/142 , LTE, CL S22 ZH0809 KIT, NEO, FREEHUB, 6-PAWL, SHIMANO (GRAY) ZH0810 KIT, NEO, FREEHUB, 6-PAWL, SRAM XD (GRAY) ZH0812 KIT, NEO, FREEHUB, 6-PAWL, CAMPY (GRAY) ZH0817 KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC ZH0802 KIT, NEO, CASSETTE SPACER, 10SP (SILVER) ZH0813 KIT, NEO, END CAP SEALS, FRONT AND REAR ZH0799 KIT, NEO, FREEHUB SEALS * denotes optional hub configuration **includes seals for all configurations 2 Page 41 1 A HUB, REAR, STANS, NEO ULTIMATE, CL, 12x142, TA 1 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL B B 2 4 1 3 1 3 4 A A # 1 2 3 * 4 KIT # ZH0800 ZH0798 ZH0814 ZH0815 ZH0799 KIT DESCRIPTION KIT, NEO, SPRING AND PAWL 6PC KIT, NEO, FREEHUB SPACER (RED) KIT, BEARING, #15267, 15X26X7MM, CHROME (GRAY) 2PC KIT, BEARING, #15267, 15X26X7MM, STAINLESS (ORANGE) 2PC KIT, NEO, FREEHUB SEALS (BLACK) * denotes optional hub configuration 2 FREEHUB, STANS, NEO, 4-PAWL, SHIMANO Page 42 1 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL B B 2 4 3 1 1 3 A # 1 2 3 * 4 KIT # ZH0800 ZH0798 ZH0814 ZH0815 ZH0799 KIT DESCRIPTION KIT, NEO, SPRING AND PAWL 6PC KIT, NEO, FREEHUB SPACER (RED) KIT, BEARING, #15267, 15X26X7MM, CHROME (GRAY) 2PC KIT, BEARING, #15267, 15X26X7MM, STAINLESS (ORANGE) 2PC KIT, NEO, FREEHUB SEALS (BLACK) * denotes optional hub configuration 2 4 FREEHUB, STANS, NEO, 4-PAWL, SRAM XD Page 43 1 A 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL B B 2 4 1 3 1 3 A 4 5 # 1 2 3 * 4 5 * KIT # ZH0800 ZH0798 ZH0814 ZH0815 ZH0799 ZH0803 ZH0804 KIT DESCRIPTION KIT, NEO, SPRING AND PAWL 6PC KIT, NEO, FREEHUB SPACER (RED) KIT, BEARING, #15267, 15X26X7MM, CHROME (GRAY) 2PC KIT, BEARING, #15267, 15X26X7MM, STAINLESS (ORANGE) 2PC KIT, NEO, FREEHUB SEALS (BLACK) KIT, NEO, SINGLESPEED LOCKRING KIT, NEO, SINGLESPEED SPACER KIT * denotes optional hub configuration 2 FREEHUB, STANS, NEO, 4-PAWL, SINGLESPEED Page 44 1 A 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL B B 4 2 1 3 1 3 4 A A # 1 2 * 3 4 KIT # ZH0800 ZH0798 ZH0814 ZH0815 ZH0799 KIT DESCRIPTION KIT, NEO, SPRING AND PAWL 6PC KIT, NEO, FREEHUB SPACER (RED) KIT, BEARING, #15267, 15X26X7MM, CHROME (GRAY) 2PC KIT, BEARING, #15267, 15X26X7MM, STAINLESS (ORANGE) 2PC KIT, NEO, FREEHUB SEALS (BLACK) * denotes optional hub configuration 2 FREEHUB, STANS, NEO, 6-PAWL, SHIMANO Page 45 1 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL B B 4 2 3 1 1 3 A # 1 2 * 3 4 KIT # ZH0800 ZH0798 ZH0814 ZH0815 ZH0799 KIT DESCRIPTION KIT, NEO, SPRING AND PAWL 6PC KIT, NEO, FREEHUB SPACER (RED) KIT, BEARING, #15267, 15X26X7MM, CHROME (GRAY) 2PC KIT, BEARING, #15267, 15X26X7MM, STAINLESS (ORANGE) 2PC KIT, NEO, FREEHUB SEALS (BLACK) * denotes optional hub configuration 2 4 FREEHUB, STANS, NEO, 6-PAWL, SRAM XD Page 46 1 A 2 1 EIS-010 NEO INTERACTIVE HUB SERIES MANUAL B B 4 2 3 1 1 3 A 4 5 # 1 2 3 * 4 5 * KIT # ZH0800 ZH0798 ZH0814 ZH0815 ZH0799 ZH0803 ZH0804 KIT DESCRIPTION KIT, NEO, SPRING AND PAWL 6PC KIT, NEO, FREEHUB SPACER (RED) KIT, BEARING, #15267, 15X26X7MM, CHROME (GRAY) 2PC KIT, BEARING, #15267, 15X26X7MM, STAINLESS (ORANGE) 2PC KIT, NEO, FREEHUB SEALS (BLACK) KIT, NEO, SINGLESPEED LOCKRING KIT, NEO, SINGLESPEED SPACER KIT * denotes optional hub configuration 2 FREEHUB, STANS, NEO, 6-PAWL, SINGLESPEED Page 47 1 A
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 47 XMP Toolkit : NitroPro 9.5 Modify Date : 2015:12:07 10:04:15-05:00 Language : en-US Tagged PDF : Yes Create Date : 2015:12:02 18:26:06-05:00 Creator : Microsoft® Word 2013 Author : James Malta Producer : Microsoft® Word 2013EXIF Metadata provided by EXIF.tools