AX 7101 Philips AX21xxx 51xxx 71xxx~3140 785 22870
User Manual: AX 7101
Open the PDF directly: View PDF .
Page Count: 24
Download | |
Open PDF In Browser | View PDF |
Portable compact disc player AX 2100 AX 2101 AX 2102 AX 5100 AX 5101 AX 5102 AX 5103 AX 5104 AX 5111 AX 5112 AX 5113 AX 5114 AX 5115 AX 5116 AX 5117 AX 5118 AX 7101 AX 7104 AX 7113 all versions PRODUCT FAMILY FOCUS ESP TABLE OF CONTENTS Technical specification ......................................................1-1 Connections and controls ..................................................1-2 Features ............................................................................1-3 Accessories .......................................................................1-3 Safety & Warnings .............................................................1-4 Service hints Repair positions ............................................................2-1 Dismantling CD-door .....................................................2-1 Handling chip components............................................2-2 Service tools..................................................................2-2 Pin description of ICs ................................................3-1...3-3 Start-up procedure.............................................................3-4 Service Test Program................................................3-5...3-6 © Copyright Blockdiagram .....................................................................3-7 Circuit diagrams CD part ..........................................................................4-1 Control / Supply partpart ...............................................4-2 Audio part......................................................................4-3 PCB layout diagram Componentside view .....................................................4-4 Copperside view............................................................4-5 Exploded view ...................................................................5-1 Mechanical partslist ...........................................................5-1 Electrical partslist ......................................................6-1...6-4 2001 Philips Consumer Electronics B.V. Eindhoven, The Netherlands CLASS 1 LASER PRODUCT All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by YT 0150 Service Audio Printed in The Netherlands Subject to modification © 3140 785 22870 1-1 TECHNICAL SPECIFICATION General Shock resistance Dimensions (WxHxD) Weight without batteries : 129x26x140mm : 220g +X/-X direction +Y/-Y direction +Z/-Z direction : ≥2.5g : ≥2.5g : ≥2.0g Power supply modes Headphone out (measured with 16Ω load, DBB/ESP off) DC-in socket : 2.5-6.0V Primary batteries (2xLR6) : 1.7-3.6V Rechargable batteries (AY3362) : 1.7-3.6V Output power (THD=10%) /17 version only : 2x12mW (+1/-3dB) all other versions : 2x6mW (+1/-3dB) Frequency response (1mW) : 100Hz-20kHz within 6dB S/N ratio (unwght) : ≥80dB (83dB typ.) S/N ratio (A-wght) : ≥82dB (85dB typ.) THD+N (1kHz, 1mW) : ≤1% (0.2% typ.) Channel crosstalk (1kHz, no load) : ≤-24dB (-44dB typ.) Channel unbalance (-40dB) : ≤5dB Volume attenuation (1kHz) : ≥60dB Battery lifetime BATTERY TYPE ESP ON Power Save ON Primary batteries 2 x LR6 22 hours 25 hours Rechargable batteries AY3362 (1200mAh) 9 hours 10 hours Dynamic Bass Boost DBB Battery level detection Frequency response DBB STAGE DETECTION LEVEL Primary batteries Rechargable batteries Battery empty 1.8V +100/-50mV 1.8V +100/-50mV Battery weak 1 battery empty level + 0.9V ± 100mV battery empty level + 0.7V ± 100mV Battery weak 2 battery empty level + 0.6V ± 100mV battery empty level + 0.5V ± 100mV Laser Battery weak 3 battery empty level + 0.3V ± 100mV battery empty level + 0.3V ± 100mV Output power Wavelength DBB 1 63kHz 1kHz 10kHz +8dB ± 2dB 0dB ± 2dB 0dB ± 2dB : <5mW (3mW typ.) : 780nm Charge section (not on all versions) Measurement setup Charge current Charge time for 80% AY3362 Charge time for 100% AY3362 Max. charge time (µP controlled) Temperature protection Use Audio Signal disc SBC429 : 250mA ±10% : 4.0h nom. : 6.0h nom. : 7h : 50°C ±5°C 4822 397 30184 Use Audio Signal Disc SBC429 4822 397 30184 (replaces test disc 3) L.P.F. = 13 th order filter 4822 395 30204 Low pass filter 22kHz DUT L Current consumption CDDA-playback R S/N and distortion meter DC-IN SUPPLY (4.5V) BATT. SUPPLY (2.25V) ESP OFF ESP ON ESP OFF ESP ON Play-mode 100mA typ. 100mA typ. 120mA typ. 120mA typ. Jump-mode 220mA typ. 220mA typ. 300mA typ. 300mA typ. OPERATION MODE Charge-mode 400mA typ. n/a Backlighting (additional) 50mA typ. 50mA typ. Stand-by (excl. recharge) 30mA typ. 50µ A typ. e.g. Sound Technology ST1700B LEVEL METER e.g. Sennheiser UPM550 with FF-filter 1-2 CONNECTIONS AND CONTROLS AX21.. & AX51.. AX71.. 5 6 4 DB B 7 TRA CK 8 PRO GRA M 9 0 ! 3 DE MO O FF MO DE B AMIC DYN ITAL DIG ASS ST BOO CD • R ES U M E • REW 2 RITA B OM LE C IBLE PAT 7 5 8 MOD E 4 ESP 9 PROG RA M DIGI BA SS TAL CD T BOOS E IBL BASS MPAT MIC DYNA ABLE CO RIT REW 3 0 ! @ H O LD 6 OF F 2 •R ES UM E• HO LD OPE LINE OUT/ N 1 VOL. 1 LIN EO UT / @ VOL. # N OPE 0 # $ $ % % ^ 1 OPEN 2..............opens the CD lid 1 OPEN 2..............opens the CD lid 2 9 ......................stops CD play, clears a program or switches the player off 2 2;....................switches the player on, starts or pauses CD play 3 ∞.....................skips and searches CD tracks backwards 3 9 ......................stops CD play, clears a program or switches the player off 4 2;....................switches the player on, starts or pauses CD play 4 §.....................skips and searches CD tracks forwards 5 §.....................skips and searches CD tracks forwards 5 ESP .................ELECTRONIC SKIP PROTECTION ensures continues CD playback regardless of vibrations and shocks 6 DBB .................switches the bass enhancement on and off. This button also switches acoustic feedback (the beep) on/off when it is pressed for more than 2 seconds 7 ........................display 6 MODE..............selects the different playing possibilities: SHUFFLE, SHUFFLE REPEAT ALL, REPEAT, REPEAT ALL and SCAN 8 PROGRAM......programs tracks and reviews the program 7 ........................display 9 MODE..............selects the different playing possibilities: SHUFFLE, SHUFFLE REPEAT ALL, REPEAT, REPEAT ALL and SCAN 8 PROGRAM......programs tracks and reviews the program 0 RESUME .........stores the last position of a CD track played HOLD ..............locks all buttons OFF .................switches RESUME and HOLD off ! LINE OUT/p ....3.5 mm headphone socket, socket to connect the player to another audio input of an additional appliance, remote control socket (not on all versions) @ VOL E ..........adjusts the volume # 4.5V DC...........socket for external power supply $ ........................belt clip holder % ........................typeplate 9 BASS...............switches the bass enhancement on and off. This button also switches acoustic feedback (the beep) on/off when it is pressed for more than 2 seconds 0 ∞.....................skips and searches CD tracks backwards ! RESUME .........stores the last position of a CD track played HOLD ..............locks all buttons OFF .................switches RESUME and HOLD off @ LINE OUT/p ....3.5 mm headphone socket, socket to connect the player to another audio input of an additional appliance, remote control socket (not on all versions) # VOL E ..........adjusts the volume $ 4.5V DC...........socket for external power supply % ........................belt clip holder ^ ........................typeplate For more information of operation instruction please visit Philips Audio internet site : http://www.audio.philips.com 1-3 AX5112 AX5113 AX5114 AX5115 AX5116 AX5117 AX5118 AX7101 AX7104 AX7113 ● AX5111 ● AX5104 ● AX5103 ● AX5102 AX5100 ● AX5101 AX2102 CD-RW COMPATIBILITY AX2101 FEATURES OF CD-PORTABLE PRODUCT FAMILY FOCUS ESP AX2100 FEATURES ● ● ● ● ● ● ● ● ● ● ● ● ● ● ELECTRONIC SKIP PROTECTION 12s 12s 12s 45s ESP DRAM SIZE [Mbit] HOLD / RESUME FUNCTION ●/● ●/● ●/● ●/● ●/● ●/● ●/● ●/● ●/● ●/● ●/● ●/● ●/● ●/● ●/● ●/● ●/● ●/● ●/● 16 16 16 45s 16 16 45s 45s 45s 45s 45s 45s 45s 45s 45s 45s 45s 100s 100s 100s 16 16 16 16 16 16 16 16 16 16 16 32 32 32 DBB STAGES 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ACOUSTIC FEEDBACK ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● PROGRAM MEMORY 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 RECHARGE NiCd / NiMH BELT-CLIP --/-- --/-- ●/● --/-- --/-- ●/● --/-- ●/● --/-- ●/● --/-- --/-- --/-- --/-- --/-- --/-- --/-- ●/● --/-- ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● -- -- -- -- -- -- -- ● -- -- -- ● -- -- -- ● ● ● ● CORD REMOTE CONTROL --/-- --/-- --/-- --/-- --/-- --/-- --/-- --/-- --/-- --/-- --/-- --/-- LINE / OPT. DIGITAL OUTPUT --/-- --/-- --/-- --/-- --/-- --/-- --/-- AY3170/00 AC/DC Adaptor AY3170/02 AC/DC Adaptor AY3170/05 AC/DC Adaptor O X X /17 AX7113 /00 AX7104 /17 AX7101 /17 AX5118 /17 AX5117 /17 AX5116 /17 AX5115 /17 AX5114 X X X X 4822 219 10672 X X X AY3170/10 AC/DC Adaptor AY3170/12 AC/DC Adaptor 4822 219 10681 4822 219 10671 AY3170/17 AC/DC Adaptor AY3266/00 Pouch (Neoprene) AY3362/00 Rechargable Batt. NiMH AY3464 HiFi Cord (3.5mm L-plug→cinch) AY3501/00 Car Adaptor Cassette 4822 219 10616 3140 113 10360 O O O O 3103 308 84120 4822 320 11881 O O O O 4822 397 10059 O O O O O O O O O O O O O O O O O X X X O O O O O O O O O O O O O O O X X O O O O O O O O O X X X AY3545/00 Car DC/DC Converter 4822 219 10033 O O O O AY3545/17 Car DC/DC Converter AY3768/00 Cord Remote Control HE205/77 Headphone HE205/77s Headphone (S-plug) HL351/77 Headphone HL351/77s Headphone (S-plug) 3140 118 32970 3140 118 50980 9082 100 00615 X 9082 100 00616 9082 100 00639 9082 100 00641 BELT-CLIP 3103 304 70250 X X...supplied with the set, O...optional available /17 /00 AX5113 /17 AX5112 /17 AX5111 /05 /10 X /00c AX5104 /01 AX5103 /00 AX5102 /11 /00c AX5101 /00 AX5100 X /05 /00 AX2002 4822 219 10617 O X 4822 219 10676 ACCESSORIES FOR CD-PORTABLE PRODUCT FAMILY FOCUS ESP /00c AX2100 /00c AX2101 ACCESSORIES O O X X X X X X X X O O O O O X O O O O O O O O X X X X X O O O O O X O X O X X X X X X X X X X X O O O X O O X O O O O O O O O O O O O X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 1-4 SAFETY & WARNINGS © ESD WARNING All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD). Careless handling during repair can reduce life drastically. When repairing, make sure that you are connected with the same potential as the mass of the set via a wristband with resistance. Keep components and tools at this potential. f ATTENTION Tous les IC et beaucoup d´autres semi-conducteurs sont sensibles aux décharges statiques (ESD). Leur longévite pourrait être considérablement écourtée par le fait qu´aucune précaution nést prise à leur manipulation. Lors de réparations, s´assurer de bien être relié au même potentiel que la masse de l´appareil et enfileer le bracelet serti d´une résistance de sécurité. Veiller à ce que les composants ainsi que les outils que l´on utilise soient également à ce potentiel. © ñ WAARSCHUWING Alle IC´s en vele andere halfgeleiders zijn gevoelig voor electrostatische ontladingen (ESD). Onzorgvuldig behandelen tijdens reparatie kan de levensduur drastisch doen vermindern. Zorg ervoor dat u tijdens reparatie via een polsband met weerstand verbonden bent met hetzelfde potentiaal als de massa van het apparaat. Houd componenten en hulpmiddelen ook op ditzelfde potentiaal. d i WARNUNG AVVERTIMENTO Tutti IC e parecchi semi-conduttori sono sensibili alle scariche Alle ICs und viele andere Halbleiter sind empfindlich statiche (ESD). gegenüber elektrostatischen Entladungen (ESD). La loro longevità potrebbe essere fortemente ridatta in caso di Unsorgfältige Behandlung im Reparaturfall kann die non osservazione della più grande cauzione alla loro Lebensdauer drastisch reduzieren. manipolazione. Durante le riparationi occorre quindi essere Sorgen Sie dafür, daß Sie im Reparaturfall über ein Pulscollegato allo stesso potenziale che quello della massa armband mit Widerstand mit dem Massepotential des delápparecchio tramite un braccialetto a resistenza. Gerätes verbunden sind. Assicurarsi che i componenti e anche gli utensili con quali si Halten Sie Bauteile und Hilfsmittel ebenfalls auf diesem lavora siano anche a questo potenziale. Potential. AVAILABLE ESD PROTECTION EQUIPMENT : anti-static table mat large 1200x650x1.25mm small 600x650x1.25mm 4822 466 10953 4822 466 10958 anti-static wristband 4822 395 10223 connection box (3 press stud connections, 1MΩ) 4822 320 11307 extendible cable (2m, 2MΩ, to connect wristband to connection box) 4822 320 11305 connecting cable (3m, 2MΩ, to connect table mat to connection box) 4822 320 11306 earth cable (1MΩ, to connect any product to mat or to connection box) 4822 320 11308 KIT ESD3 (combining all 6 prior products - small table mat) 4822 310 10671 wristband tester 4822 344 13999 SAFETY © ñ Safety regulations require that the set be restored to its original condition and that parts which are identical with those specified be used. Safety components are marked by the symbol Veiligheidsbepalingen vereisen, dat het apparaat in zijn oorspronkeliijke toestand wordt teruggebracht en dat onderdelen, identiek aan de gespecificeerde, worden toegepast. De Veiligheidsonderdelen zijn aangeduid met het symbool f i Les normes de sécurité exigent que l`appareil soit remis à l`état d`origine et que soient utilisées les pièces de rechange identiques à celles spécifiées. Les composants de sécurité sont marqués Le norme di sicurezza estigono che l´apparecchio venga rimesso nelle condizioni originali e che siano utilizzati i pezzi di ricambiago identici a quelli specificati. Componenty di sicurezza sono marcati con © DANGER: Invisible laser radiation when open. AVOID DIRECT EXPOSURE TO BEAM. d Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu beachten. Der Originalzustand des Gerätes darf nicht verändert werden. Für Reparaturen sind Originalersatzteile zu verwenden. Sicherheitsbauteile sind durch das Symbol markiert. CLASS 1 LASER PRODUCT s Varning ! ∂ Advarsel ! ß Varoitus ! Osynlig laserstrålning när apparaten är öppnad och spärren är urkopplad. Betrakta ej strålen. Usynlig laserstråling ved åbning når sikkerhedsafbrydere er ude af funktion. Undgå udsaettelse for stråling. Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina näkymättömälle laserisäteilylle. Älä katso säteeseen ! © f After servicing and before returning the set to customer perform a leakage current measurement test from all exposed metal parts to earth ground, to assure no shock hazard exists. The leakage current must not exceed 0.5mA. "Pour votre sécurite, ces documents doivent être utilisés par des spécialistes agréés, seuls habilités à réparer votre appareil en panne". 2-1 SERVICE HINTS REPAIR POSITION COPPERSIDE REPAIR POSITION COMPONENTSIDE To get access to the copperside of the printed board assembly proceed as follows: To get access to the componentside of the printed board assembly proceed as follows: 1. 2. 3. 4. 1. 2. 3. 4. 5. Remove the bottom screws (6x) Lift the bottom-cabinet Supply the unit via external DC-socket Take care that the door switch is closed during measurements Remove the bottom screws (6x) Open the CD-door Lift the top-cabinet and put it backwards on the table Supply the unit via the external DC-socket Take care that the door switch is closed during measurements DISMANTLING THE CD-DOOR To dismantle the CD-door proceed as follows: 1. Dismantle bottom and printed board/drive assembly 2. Disconnect membrane keyboard (flex-foil connector on copperside of printed board) 3. Bend the cabinet leftwards downwards 1, while bending the CD-door rightwards upwards 2 The procedure appears to be tricky at first, but force needs to be applied with thumb and middle finger only. It’s just like snapping one’s fingers. Remark: Don’t worry about applied force - both parts have a solid design. However, do not use screwdrivers or tools like that. Sharp edges could damage hinge or cabinet part. 2-2 HANDLING CHIP COMPONENTS SERVICE TOOLS Audio signal disc SBC429 Playability test disc SBC444 Test disc 5 (disc without errors) + Test disc 5A (disc with dropout errors, black spots and fingerprints) SBC426/SBC426A 4822 397 30184 4822 397 30245 4822 397 30096 ESD PROTECTION EQUIPMENT Anti-static table mat large 1200x650x1.25mm small 600x650x1.25mm Anti-static wristband Connection box (3 press stud connections, 1Mø) Extendible cable (2m, 2Mø, to connect wristband to connection box) Connecting cable (3m, 2Mø, to connect table mat to connection box) Earth cable (1Mø, to connect any product to mat or to connection box) KIT ESD3 (combining all 6 prior products - small table mat) Wristband tester 4822 466 10953 4822 466 10958 4822 395 10223 4822 320 11307 4822 320 11305 4822 320 11306 4822 320 11308 4822 310 10671 4822 344 13999 3-1 PIN DESCRIPTION OF INTEGRATED CIRCUITS TZA1024 – HF-PREAMPLIFIER AND LASER SUPPLY CIRCUIT Pin Name Direction Description ––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– 1 LD HF-preamp → CD-drive current output to laser diode 2 VCCL +2.6V laser supply voltage 3 CFIL → HF-preamp external filter capacitor 4 MON CD-drive → HF-preamp laser monitor diode input 5 DIN CD-drive → HF-preamp central diode input 6 GND GND ground 7 PWRON CD10 → HF-preamp power-on select input 8 CMFB +2.6V / 2 common mode feedback voltage input 9 RFFB → HF-preamp external RF feedback resistor 10 RFEQO HF-preamp → RF amplifier output 11 CDRW CD10 → HF-preamp gain select input for CDDA/CDRW 12 EQSEL CD10 → HF-preamp equalizer/speed select input 13 VCC2 +2.6V supply voltage 14 RGADJ GND external laser supply gain adjust resistor SC111259FTA – SERVO DRIVER & POWER MANAGEMENT IC Pin Name Direction Description ––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– 1 SLEEP µP → servo driver sleep input 2 WAKW µP → servo driver wake input 3 VR +VR reference voltage input (motor driver) 4 ERR4 CD10 → servo driver control signal input (slide error signal) 5 CF4 → servo driver phase correction capacitor connect (CH4) 6 CF3 → servo driver phase correction capacitor connect (CH3) 7 ERR3 CD10 → servo driver control signal input (radial error signal) 8 ERR2 CD10/µP → servo driver control signal input (disc speed error signal) 9 CF2 → servo driver phase correction capacitor connect (CH2) 10 CF1 → servo driver phase correction capacitor connect (CH1) 11 ERR1 CD10 → servo driver control signal input (focus error signal) 12 OUT1A servo driver → CD-drive positive drive output (CH1) 13 PGND1 GND H-bridge driver ground 14 OUT1B servo driver → CD-drive negative drive output (CH1) 15 VIN12 +A CH1 and CH2 H-bridge driver supply voltage 16 OUT2B servo driver → CD-drive negative drive output (CH2) 17 PGND2 GND H-bridge driver ground 18 OUT2A servo driver → CD-drive positive drive output (CH2) 19 OUT3A servo driver → CD-drive positive drive output (CH3) 20 PGND2 GND H-bridge driver ground 21 OUT3B servo driver → CD-drive negative drive output (CH3) 22 VIN34 +A CH3 and CH4 H-bridge driver supply voltage 23 OUT4B servo driver → CD-drive negative drive output (CH4) 24 PGND4 GND H-bridge driver ground 25 OUT4A servo driver → CD-drive positive drive output (CH4) 26 VG +VG charge pump output 27 C2H → servo driver charge pump capacitor connect 28 C1H → servo driver charge pump capacitor connect 29 C1L → servo driver charge pump capacitor connect 30 C2L → servo driver charge pump capacitor connect 31 VIN battery → servo driver battery supply voltage 32 RSTB servo driver → reset block output 33 CHGSW servo driver → charge circuit transistor drive output for battery charger 34 RS charge circuit → servo driver OpAmp non-inverting input for battery charger 35 INM2 → servo driver error amplifier inverting input 36 RF2 → servo driver error amplifier output 37 DCIN +DC DC power supply from AC/DC adaptor 38 VDET servo driver → DCIN over voltage and VIN low voltage detect output 39 VREF servo driver → Voltage reference circuit output 40 DTC → servo driver max. duty control voltage input for power management 41 VOUT servo driver → DC/DC converter PWM output for power management 42 VC → servo driver power management power supply 43 CGND GND internal ground 44 RF1 servo driver → OpAmp output for power management 45 INM1 → servo driver OpAmp inverting input for power management 46 CLK → servo driver clock input 47 OE µP → servo driver output enable for motor drivers 48 CHGON µP → servo driver charge enable for battery charger 3-2 SAA7324 – DECODER, DIGITAL SERVO IC AND D/A-CONVERTER CD10 (low voltage version) Pin Name Direction Description ––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– 1 HFREF → CD10 comparator common mode input 2 HFIN → CD10 comparator signal input 3 ISLICE CD10 → current feedback from data slicer 4 VSSA1 GND analog ground 1 5 VDDA1 +2.6V analog supply voltage 1 6 IREF CD10 → reference current output pin 7 VRIN CD10 → reference voltage for servo ADC’s 8 D1 CD-drive → CD10 unipolar current input (central diode signal input) 9 D2 CD-drive → CD10 unipolar current input (central diode signal input) 10 D3 CD-drive → CD10 unipolar current input (central diode signal input) 11 D4 CD-drive → CD10 unipolar current input (central diode signal input) 12 R1 CD-drive → CD10 unipolar current input (satellite diode signal input) 13 R2 CD-drive → CD10 unipolar current input (satellite diode signal input) 14 VSSA2 GND analog ground 2 15 CROUT CD10 → X-TAL crystal/resonator output 16 CRIN X-TAL → CD10 crystal/resonator input 17 VDDA2 +2.6V analog supply voltage 2 18 LN CD10 → DAC left channel differential output - negative 19 LP CD10 → DAC left channel differential output - positive 20 VNEG GND DAC negative reference input 21 VPOS +2.6V DAC positive reference input 22 RN CD10 → DAC right channel differential output - negative 23 RP CD10 → DAC right channel differential output - positive 24 SELPLL CD10 → selects whether internal clock multiplier PLL is used 25 TEST1 GND test control input 1; this pin should be tied low 26 CL16 CD10 → DSP 16.9344 MHz system clock output 27 DATA CD10 → NPC or CD10 → DSP serial data output (3-state) 28 WCLK CD10 → NPC or CD10 → DSP word clock output (3-state) 29 SCLK CD10 → NPC or CD10 → DSP serial bit clock output (3-state) 30 EF CD10 → NPC C2 error flag output (3-state) 31 TEST2 GND test control input 2; this pin should be tied low 32 KILL CD10 → kill output (programmable; open-drain) 33 VSSD1 GND digital ground 2 34 V2/V3 CD10 → NPC versatile I/O: input versatile pin 2 or output versatile pin 3 (open-drain) 35 WCLI NPC → CD10 or DSP → CD10 word clock input (for data loopback to DAC) 36 SDI NPC → CD10 or DSP → CD10 serial data input (for data loopback to DAC) 37 SCLI NPC → CD10 or DSP → CD10 serial bit clock input (for data loopback to DAC) 38 RESETn µP → CD10 power-on reset input (active low) 39 SDA µP ↔ CD10 microcontroller interface data I/O line (open-drain output) 40 SCL µP → CD10 microcontroller interface clock line input 41 RAB µP → CD10 microcontroller interface R/W and load control line input (4-wire bus mode) 42 SILD µP → CD10 microcontroller interface R/W and load control line input (4-wire bus mode) 43 STATUS CD10 → servo interrupt request line/decoder status register output (open-drain) 44 TEST3 GND test control input 3; this pin should be tied low 45 RCK → CD10 subcode clock input 46 SUB CD10 → P-to-W subcode bits output (3-state) 47 SFSY CD10 → µP subcode frame sync output (3-state) 48 SBSY CD10 → NPC subcode block sync output (3-state) 49 CL11/4 CD10 → DSP 11.2896 MHz or 4.2336 MHz (for microcontroller) clock output 50 VSSD2 GND digital ground 3 51 DOBM CD10 → bi-phase mark output (externally buffered; 3-state) 52 VDDD1P +2.6V digital supply voltage 2 for periphery 53 CFLG CD10 → correction flag output (open-drain) 54 RA CD10 → servo driver radial actuator output 55 FO CD10 → servo driver focus actuator output 56 SL CD10 → servo driver slide control output 57 VDDD2C +2.6V digital supply voltage 3 for core 58 VSSD3 GND digital ground 4 59 MOTO1 CD10 → servo driver motor output 1; versatile (3-state) 60 MOTO2 CD10 → motor output 2; versatile (3-state) 61 V4 CD10 → HF-preamp versatile output pin 4 62 V5 CD10 → HF-preamp versatile output pin 5 63 V1 innerswitch → CD10 versatile input pin 1 64 LDON CD10 → HF-preamp laser drive on output (open-drain) 3-3 SM5907AF – COMPRESSION-TYPE ANTI-SHOCK MEMORY CONTROLLER NPC Pin Name Direction Description ––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– 1 VDD2 +2.6V supply voltage 2 UC1 NPC ↔ µP interface extension I/O line 1 3 UC2 NPC ↔ µP interface extension I/O line 2 4 UC3 NPC ↔ µP interface extension I/O line 3 5 UC4 NPC ↔ µP interface extension I/O line 4 6 UC5 NPC ↔ µP interface extension I/O line 5 7 NACS3 NPC → DRAM DRAM2 CAS control 8 TEST2 +2.6V test pin 9 CLK CD10 → NPC 16.9344MHz clock input 10 VSS GND ground 11 YSRDATA CD10 → NPC audio serial data input 12 YLRCK CD10 → NPC audio serial L/R clock input 13 YSCK CD10 → NPC audio serial bit clock input 14 ZSCK NPC → CD10 audio serial bit clock output 15 ZLRCK NPC → CD10 audio serial L/R clock output 16 ZSRDATA NPC → CD10 audio serial data output 17 YFLAG CD10 → NPC signal processor IC RAM overflow flag 18 YFCLK GND crystal-controlled frame clock input 19 YBLKCK CD10 → NPC subcode block clock signal output 20 RESET µP → NPC system reset input (active low) 21 ZSENSE NPC → µP interface status output 22 VDD1 +2.6V supply voltage 23 YDMUTE → NPC forced mute input 24 YMLD µP → NPC µP interface latch clock input 25 YMDATA µP → NPC µP interface serial data input 26 YMCLK µP → NPC µP interface shift clock input 27 A10/NCAS2 NPC → DRAM DRAM OE control output (active low) 28 CAS NPC → DRAM DRAM CAS control output (active low) 29 D2 NPC ↔ DRAM DRAM data input/output 2 30 D3 NPC ↔ DRAM DRAM data input/output 3 31 D0 NPC ↔ DRAM DRAM data input/output 0 32 D1 NPC ↔ DRAM DRAM data input/output 1 33 WE NPC → DRAM DRAM WE control output (active low) 34 RAS NPC → DRAM DRAM RAS control output (active low) 35 A9 NPC → DRAM DRAM address output 9 36 A8 NPC → DRAM DRAM address output 8 37 A7 NPC → DRAM DRAM address output 7 38 A6 NPC → DRAM DRAM address output 6 39 A5 NPC → DRAM DRAM address output 5 40 A4 NPC → DRAM DRAM address output 4 41 A0 NPC → DRAM DRAM address output 0 42 A1 NPC → DRAM DRAM address output 1 43 A2 NPC → DRAM DRAM address output 2 44 A3 NPC → DRAM DRAM address output 3 3-4 START-UP PROCEDURE – FLOW CHART START-UP PROCEDURE - FLOW CHART Start-up procedure for ext.DC supply, no accu inserted, hold-switch in off pos., ESP on, resume-mode off, CD-door closed. POWER OFF (stand-by) PLAY pressed ? focus found during ramping cycle ? N Y N µP sends new focus parameters to CD10 (switch to higher focus sensitivity) Y µP calculates ramping offset and sends play-params to CD10 DC/DC converter is switched on (via WAKE) Y µP resets CD10 and NPC PORES=L NPC_RESET=L re-initialize CD10 and restart focus search procedure N µP initializes CD10 and NPC with default parameter/settings focus found during ramping cycle ? focus stability test ok ? N already looped through all (4) focus sensitivities ? Y µP accelerates disc to nom. speed N Y µP switches headphone amplifier on (via LF_POW) re-initialize CD10 and restart focus search procedure N µP outputs servo signal for disc motor (DM_PWM 50% duty) switch back to normal focus sensitivity disc at nom. speed within ~10s ? Y Y µP initializes radial servo loop (~330ms) µP switches servo driver on (via S_MUTE) N µP sends new focus parameters to CD10 (switch to higher focus sensitivity) µP releases muting (via MUTE) µP sends command to CD10: “move slide inside” µP sends command to CD10: “jump 10 tracks inside” inner switch closed within ~6s ? N subcode error handler already looped through all (4) focus sensitivities ? jump ok ? Y Y N N focus found during ramping cycle ? N N µP sends command to CD10: “move slide outside” Y radial error handler Y inner switch open within ~0.25s ? focus found during ramping cycle ? subcode ok ? Y Y µP sends commands to CD10: “slide servo off” TOC found within ~30s ? N Y µP accelerates disc motor for ~200ms µP sends commands to CD10: “laser on” “focus servo on” PLAY-MODE display shows “nF d1SC” start-up stopped display shows “no d1SC” start-up stopped N 3-5 SERVICE TEST PROGRAM 1. PRELIMINARY SETUP • To enter the service test program disconnect the AC/DC adaptor and remove batteries, open the CD-door and hold the buttons “PLAY” & “PREV” depressed while turning power on (i.e. connecting the AC/DC adaptor). • The display shows the software version of the built-in µP (i.e. “ S-26”). Versions are counted from “ 00” onwards; that means the higher the number the newer the software. • The program is now in the main menu – various tests can be entered by pressing the corresponding buttons (see flow chart on next page or detailed description of available tests below). • To exit the service test program press the “STOP“ button or disconnect the set from the power source. 6. FOCUS TEST Purpose: Check movement of lens and operation of focus servo for CDDA and CDRW discs. 2. DISPLAY TEST Purpose: Check functionality of display and display driver. • To enter the display test start the service test program and press the “NEXT” button. • The display shows test pattern1. All segments are activated for finding open circuits (see flow chart on next page). • To jump to the next pattern press the “NEXT” button. • The display shows test pattern2. All alternate pins (2, 4, ...) are activated for finding short circuits (see flow chart on next page). • To jump back to test pattern1 press the “NEXT” button, to exit the display test and return to the main menu press the “STOP” button. • The focus servo loop is switched on and the set starts searching the focus (“focus ramping”). As soon as the focus has been found the focus servo loop is closed and the state of the focus is monitored continuously. • If the focus is OK the display shows “ F x”, else “-F x”. “x” indicates the sensitivity mode. Details can be found in table3 (see flow chart on next page). • To toggle between sensitivity modes press the “BASS” button. • To move slide outside hold the “NEXT” button depressed. • To move slide inside hold the “PREV” button depressed. • To accelerate the discmotor clockwise hold the “MODE” button depressed. • To accelerate the discmotor counter-clockwise hold the “PROG” button depressed. • In case the focus is OK the discmotor test can be entered by pressing the “PLAY” button, to exit the focus test and return to the main menu press the “STOP” button. 3. KEY TEST Purpose: Check operation of keys and cord remote control. • To enter the key test start the service test program and press the “MODE” button. • The display shows “--”. • Hold key depressed and check corresponding key code on the display. Key codes can be found in table1 (see flow chart on next page). • To exit the key test and return to the main menu press the “STOP” button. 4. PLAYBACK TEST WITH ERROR ANALYSIS Purpose: Analyze errors that occur during playback and search for intermittent failures. • To enter the playback test start the service test program and press the “BASS” button. • To start the error analysis press the “PLAY” button. Note that the playback test can only be entered if the CD-door is closed. • The set will read the TOC and start playback. As long as the playback is free of errors the display shows track and time information like in normal play-mode. In case of errors corresponding error codes will be displayed. The meaning of these error codes can be found in table2 (see flow chart on next page). Note: Errors can either be “fatal” or “non fatal”. Fatal errors always stop the playback, non fatal errors only cause a short interruption of the music. Fatal errors are displayed as long as the set is connected to the power source, non fatal errors are displayed until a new error occurs or a button is pressed. • To stop the playback test disconnect the set from the power source. 5. SERVO TEST Purpose: Check door switch, inner switch of CD-drive, movement of slide and acceleration of discmotor. • To enter the servo test start the service test program and press the “PLAY” button. • The display shows “Cd xy”. “x” indicates state of door switch; “y” indicates state of inner switch. x,y = “0” means switch is closed; “ 1” means switch is open. • To move slide outside hold the “NEXT” button depressed. • To move slide inside hold the “PREV” button depressed. • To accelerate the discmotor clockwise hold the “MODE” button depressed. • To accelerate the discmotor counter-clockwise hold the “PROG” button depressed. • To enter the focus test press the “PLAY” button, to exit the servo test and return to the main menu press the “STOP” button. Since the CDRW reflects much less light than an ordinary CDDA, the gain of the HF-amplifier stage and the sensitivity of the ADC inside the Decoder&Digital Servo IC “CD10” must be adapted accordingly. The gain is switched via the CDRW input of the HF-preamplifier. The ADC-sensitivity is set via software parameters (sent from µP to “CD10”). In total, there are 4 sensitivity modes available: 1 for CDDA and 3 for CDRW. The modes are listed in table3 (see next page). In normal play-mode, the correct focus sensitivity is choosen automatically during start-up (see “Start-up procedure” on previous page). In the service test program, the sensitivity can be choosen manually in order to allow individual measurements in several modes. 7. DISCMOTOR TEST Purpose: Check speed regulation of discmotor. • The speed regulation is switched on and the discmotor starts rotating. If the speed reaches 75% of the nom. speed the display shows “ d”, else “-d”. • In parallel also the state of the focus is monitored continuously (display “ F x” or “-F x”). • In case the disc speed is OK and the focus is OK the radial test can be entered by pressing the “PLAY” button, to exit the discmotor test and return to the main menu press the “STOP” button. 8. RADIAL TEST Purpose: Check if radial loop locks and an audio signal is audible at the headphone output. • The radial servo loop is switched on, mute is released and the audio signal is audible. If the system is on track the display shows “ r”, else “-r”. • In parallel also the disc speed (display “ d” or “-d”) and the state of the focus (display “ F x” or “-F x”) are monitored continuously. Note: In case of radial errors the audio output is muted and muting is not released automatically when the systems recovers from the error. “ -r” remains on the display. To open mute again press the “NEXT” or “PREV” button. • To jump 16 tracks outside press the “NEXT” button. • To jump 16 tracks inside press the “PREV” button. • To exit the radial test and return to the main menu press the “STOP” button, to exit the service test program disconnect the set from the power source. Important remark: In radial test mode data to the DRAM is written at 1.2 times the nominal speed, and read from the DRAM at nominal speed. Because writing is done faster than reading the DRAM gets full after a certain time. In normal play mode the system would now wait until the DRAM is partly emptied again, jump backwards and resume filling at the last written position. However, in radial test mode the jumps would disturb measurements on the radial servo loop. Therefore this function has been disabled and filling restarts immediately from the current position of the pick-up unit. As a result “jumps” are audible during playback. 3-6 3-6 SERVICE TEST PROGRAM – FLOW CHART To enter the service test program 1. Disconnect the AC/DC adaptor and remove batteries 2. Open the CD-door 3. Hold “PLAY” & “PREV” buttons depressed 4. Connect the AC/DC adaptor or insert batteries PRELIMINARY SETUP Display shows software-version (e.g. “S-26”) CD TEST “PLAY” pressed? MAIN MENU N Y SERVO TEST “NEXT” pressed? “MODE” pressed? N Y “DBB” pressed? Y KEY TEST Display shows “--” PLAYBACK TEST key on cd-player depressed? N Display shows: “Cd xy” N ("BASS" for AX71xx) Y DISPLAY TEST 1 display shows test pattern 1 “NEXT” pressed? Remark: Playback test can only be entered if CD-door is closed! N N key on remote control depressed? N Error during playback? • State of switches x = door switch y = inner switch “0” = closed “1” = open “PLAY” pressed? N N Y “NEXT” depressed? N Y “PREV” depressed? N “MODE” depressed? Y N Y “PROG” depressed? N Y Y Y Y DISPLAY TEST 2 display shows test pattern 2 Y Display shows keycode + “rc” (see table1) Display shows keycode (see table1) Slide moves outside Display shows error-code (see table2) Disc motor turns clockwise (accelerate) Slide moves inside Disc motor turns counter-clockwise (brake) FOCUS TEST “NEXT” pressed? N Y • Focus status “ F x” = focus OK “-F x” = focus error x = focus sensitivity (see table3) Note: If focus has been lost, focus start-up procedure is entered (ramping). N Fatal error? Y Stop playback ATTENTION: FROM THIS TEST ONWARDS THE LASER IS SWITCHED ON !! → AVOID DIRECT EXPOSURE TO BEAM !! ("BASS" for AX71xx) test pattern 1 (all segments activated) DBB program resume shuffle repeat all hold “PLAY” pressed and focus OK? EXIT SERVICE TEST PROGRAM table2 – playback error analysis CODE ERROR TYPE F=Fatal error W=Warning DBB shuffle repeat all hold AX21.. AX51.. focus error W Focus point lost for at least 3ms. 1001 radial error W The radial servo was offtrack for a certain amount of time. 1002 sledge in error W The slide did not reach it´s inner pos. (inner switch of CD-drive does not close) within approx. 6s. 1003 sledge out error W The slide did not come out of it´s inner pos. (inner switch of CD-drive is open) within approx. 250ms. 1004 DRAM filling error W The DRAM controller was not able to connect two consecutive audio frames. The microcontroller had to perform a direct audio connection that produces audible clicks. AX71.. • Disc speed status “ d” = speed OK “-d” = speed error • Focus status “ F x” = focus OK “-F x” = focus error x = focus sensitivity (see table3) table1 – key test DISPLAY SET KEYS OF SET DBB (or BASS) 1 PROGRAM 2 MODE 3 PLAY 5 NEXT 6 PREVIOUS 7 ESP 8 1005 jump error 1006 subcode error 1008 turntable motor error W F During start-up, the disc speed did not reach 75% of the nom. speed within approx. 6 seconds. 4 rc PLAY 5 rc NEXT 6 rc PREVIOUS 7 rc Press “STOP” on the CD-player to exit the key test. audio error (error flag) W Uncorrectable audio error (EF error flag from CD-Decoder). 1020 focus search error F The focus point could not be found within approx. 10s (no valid TOC info), resp. 30s (valid TOC info). N RADIAL TEST table3 – focus sensitivity DISPLAY ESP-FLAG -F 01 1009 Slide moves outside • On track status “ r” = on track “-r” = not on track • Disc speed status “ d” = speed OK “-d” = speed error • Focus status “ F x” = focus OK “-F x” = focus error x = focus sensitivity No valid subcode for approx. 230ms. FOCUS SENSITIVITY off Normal focus sensitivity for CDDA -F 02 on Low focus sensitivity for high-reflective CD-RW -F 03 on Medium focus sensitivity for normal-reflective CD-RW on High focus sensitivity for low-reflective CD-RW -F 04 “NEXT” depressed? Y CUE-MODE Track servo jumps 16 tracks forwards N “PREV” depressed? Y REVIEW-MODE Track servo jumps 16 tracks backw. “NEXT” depressed? Y Y The offtrack values do not decrease properly when jumping tracks, the jump destination could not be found. KEYS OF CORD REMOTE CONTROL STOP “PLAY” and focus OK and speed OK? N Toggle focus sensitivity (see table 3) DISC MOT. TEST CAUSE “DBB” pressed? Y Y test pattern 2 (alternate segments activated) 1000 N N N “PREV” depressed? Y Slide moves inside N “MODE” depressed? Y Disc motor turns clockwise (accelerate) N “PROG” depressed? Y Disc motor turns counter-clockwise (brake) N 3-7 3-7 BLOCKDIAGRAM LCD + Keyboard (Membrane) +2.6V Only for AX71xx - ESP100 From / To RC - socket +2.6V +2.6V RC TMP86CH21 RC Circuit 16MBit DRAM TZA1024 LD Laser Power Control + HF Amplifier uP + LCD Driver HF +2.6V DA23 (LN) CD-Drive D1-4, R1-2 From/To Supply & Charging Circuit From/To Servo & Power Management 16MBit DRAM +2.6V +2.6V PWRON, EQSEL, CDRW CD10 SAA7324H +2.6V DC-IN Socket Track±, Focus±, SL±, DM± SL / FO / RA Memory Controller Digital Servo Processor & CD Decoder (w/ DAC) LP & LN DC/DC Converter & Charging Circuit SM5907AF RP & RN From uP Mute & Beep Control +2.6V SC111259FTA Servo Driver + Power Management Mute +2.6V From / To RC Circuit Beep Volume From/To uP R TDA1308 Headphone Amplifier L Battery or ACCU TC75W51FU From/To uP DBB Headphone / RC Socket 4-1 4-1 CIRCUIT DIAGRAM - CD PART 2837 E4 2838 E4 2839 E4 2840 E5 2841 E5 2842 E5 2843 C4 2844 C4 2845 C4 2846 B5 2857 F5 2858 F6 2859 F7 2860 F7 2861 B7 2852 A9 2853 A10 2854 A10 2855 A10 2856 D10 3 2 2886 D13 2887 C14 2888 F7 2889 H12 2890 B4 2862 B9 2880 E11 2881 H13 2882 G14 2885 C13 3802 B2 3803 B4 3804 A5 3805 B4 3806 C4 2891 C4 2892 C15 2893 C11 3800 A1 3801 B1 4 3807 C5 3808 C3 3809 B1 3830 C1 3831 C2 3837 D3 3838 D3 3839 D3 3840 D3 3841 D4 3832 C2 3833 C2 3834 C2 3835 E2 3836 E2 5 3847 C4 3848 C4 3849 B5 3850 C5 3851 B5 3842 D4 3843 D4 3844 D4 3845 E4 3846 E4 6 3857 A10 3858 A10 3859 A10 3860 C10 3861 C10 3852 A7 3853 A8 3854 A9 3855 A9 3856 A9 7 10 7830 B9 7880 D11 7881 C11 7882 H14 7883 C14 F835 C1 F836 D1 F837 D1 F838 D1 F839 D1 F830 C1 F831 C1 F832 C1 F833 C1 F834 C1 11 F845 F9 F846 B8 F847 G8 F848 A1 F849 A2 F840 E1 F841 D1 F842 D1 F843 E1 F844 C5 12 F856 G6 F857 G7 F858 F7 F859 D10 F860 E11 F850 B1 F851 B4 F852 B6 F854 C5 F855 G6 13 F861 G14 F862 F14 F863 C13 F864 F14 14 to CONTROL / SUPPLY-PART 100n 2859 A 29 30 31 D NCAS3 3K3 16,9MHz F858 F857 D A4 A5 A7 A6 A8 | NC 19 18 A7 | A8 17 A6 | A7 16 A5 | A6 15 A4 | A5 14 13 12 A3 | A3 11 A2 | A2 10 A1 | A1 9 A0 | A0 8 A10 | NC 16 MBit | 4 MBit D1 31 1,3V D0 4 2,5V 30 1,2V D3 5 29 1,2V D2 2,5V 6 0V CAS 28 2,5V 7 0,6V A10 27 2,4V A3 A2 A1 A0 E 8 2,6V 26 2,0V 9 1,3V 25 1,8V 10 0V 24 2,7V F864 23 0V 3889X F861 22 SCL F F862 SDA +2.6V YMLD 1K 3887 100n D D 3886 0V 10K 3885 8 9 10 11 12 1,8V 7882 BC847BW NPC_RESET 100n 2881 10p 2889 10K G +2.6V 22R D +2.6V D 7 21 0V 20 2,6V 19 0V 18 0V 17 0,1V 16 2882 F847 15 3884 0,9V 14 1,3V 1,3V 1,3V 13 3883 1,3V KILL +Audio E_KILL RP RN LP LN A10 32 1,2V 3 2,5V A ... only for ESP100 X ... component only provided (not in use) 6 OE | OE 22 21 A9 | NC 2 2,5V Item 3877 ... only for 8.46MHz * Item 3878 ... only for 33.86MHz 5 RAS | A9 WE to AUDIO-PART 4 NC | NC 33 2,5V 3882 3 5 1 2,6V 12 3 2 RAS WE A9 RAS 2,4V 35 34 0V 0V D3 D2 22u A8 36 D D +2.6V G 6 CAS | CAS 23 I/03 | I/03 24 WE | RAS I/04 | I/04 25 3 I/02 | WE 2892 A 100n A7 37 0V A3 A6 38 22R D 0V A2 A5 39 0V A1 A4 40 0V A10 A0 A0 41 0V RAS 0V WE 0V D3 0V A1 42 4 GND | GND 26 2 I/01 | I/02 7883 A 13 VCC | VCC GND | A4 DRAM_16/4 BIT 14 15 A4 | A5 A5 | A6 11 A2 | A2 12 A3 | A3 16 17 A6 | A7 10 A1 | A1 19 18 A7 | A8 A8 | NC A10 | NC A0 | A0 9 6 NC | NC 8 A9 | NC 21 OE | OE 22 5 RAS | A9 4 16 MBit | 4 MBit CAS | CAS 23 WE | RAS I/04 | I/04 25 I/03 | I/03 24 I/02 | WE 3 2886 D Item 3881 ... only for ESP12 Item 3909 ... only for ESP100 3865 F845 I/01 | I/02 2885 D ** KILL 32 F863 3890 +2.6V 11 1,3V 1 A8 A9 D1 D0 A4 A5 A6 A7 A8 A9 D1 NCAS3 0V 2,6V 28 3872 27 TEST2 WCLK DATA CL16 26 * * 1n5 47R F856 3869 F855 25 VSSD1 33 A2 43 C 100K 1n5 2860 24 3871 2888 23 D ** A3 44 B 3888 22R 22 5800 2858 21 0V TEST1 20 2.5V SELPLL 19 3878 18 ** 6 VERSAT. V2|V3 34 0,1V INTERF. 22R 3880 33n D 1,3V 17 2 D2 7 3909 1,0V 7880 SM5907 F860 2880 SDI 36 2856 5 WCLI 35 KILL 7881 +2.6V PORES 1,3V SER. DATA INTERFACE 33n D F859 SCLI 37 BITSTREAM DAC GND | GND 26 DRAM_16/4 BIT SDA 2.6V SER. DATA LOOPBACK INTERF. 2887A 33n SCL 1.9V SDA 39 RESETn 38 1 from/to CONTROL / SUPPLY-PART 10K 3864 10K RAB 0.3V SCL 40 1 VCC | I/01 3n3 1n5 2855 10K 3863 RAB 41 2893 100n AUDIO PROCESSOR SILD 2,0V PROCESSING 3868 100n 10K SILD 42 1,8V 47u A 3862 STATUS 43 PRE- 16 CRIN 1,2V VDDA2 22R 10K SRAM ADC 15 CROUT 1,3V 2857 +2.6V 3861 0V 14 VSSA2 0V 8.46MHz / 33.86MHz 3867 1n5 2854 0V RCK 45 2,1V 13 R2 1,3V * 1840 H +2.6V VCC | I/01 SUB 46 TEST3 44 3877 H SFSY 1,5V 12 R1 1,3V H 2853 0V SFSY 47 ADDR CONTROL FUNCTION 11 D4 1,3V H 3n3 SBSY 48 3860 PEAK DET. 49 CL11|4 SUBCODE PROCESSOR EBU INTERF. 50 7830 SAA7324 3881 9 D2 1,3V 2842 220p 3n3 2852 2850 51 0V 52 VSSD2 0V 53 3n3 2851 10R 3853 54 A D D D MCU_XIN 1u DOEM 0V RA 1,4V 55 CFLG 0V 56 FO 1,2V 57 Radial 2862 0V 10 D3 1,3V CAS 2K2 10R INNERSWITCH 3852 SL 1,3V 58 VDDD2C 2,6V VSSD3 0V MOTO1 0,4V V4 0V MOTO2 0,4V V5 0V 2K2 MICROCONTROLLER INTERFACE 100n 2K2 3859 OUTPUT STAGES 1.3V RP H 2K2 3856 ERROR CORR. 1.3V RN H 59 EFM DEMOD 0V VNEG H 60 DIG. PLL 2.5V VPOS H 14 7 VRIN VREF GEN. 1,3V CSTCC H 2K2 3858 8 D1 1,3V 220p 10K 180p 27K 180p 2836 10K 3846 330p 2833 3836 13 2K2 3855 +VR F846 MOTOR CONTROL 6 IREF 1,2V F854 10K 3844 27K 3835 61 5 VDDA1 2,5V 1.3V LP 10K 3843 62 TIMING 33K V1 2,6V 2,4V 10n 2849 470R 1M 47u 3807 3874 H 3857 +2.6V 2861 FRONT END 4 VSSA1 0V 3854 +2.6V 3 ISLICE 1,2V 1.3V LN 10K 3842 F H 15 Focus VERSATILE INTERFACE 1K 1,2V 2 HFIN 1,2V 47n H 63 15 D0 from CONTROL / SUPPLY-PART 22u 3K3 2802 3803 100n 2804 4K7 3K3 2803 22K 1 HFREF 2,6V 33K 3839 10K 3845 2831 F844 3850 33K 2845 220p 2841 33K H 27p 3848 220p 2840 3837 F839 F843 H 220p 2839 F842 FMN 3806 3876X 3841 33K 1 E 3840 3838 F840 22u 2844 68K F838 180p 2832 3 2 H 2843 3831 H 5 1K 1n 3851 1 220p 2838 F837 10R +2.6V 4K7 64 LDON 22n 2848 3849 33R F841 4 4K7 H 2846 3805 3847 +2.6V 2847 F851 3875 5K6 3830 3890 D14 3909 E11 5800 F8 7800 A2 7801 C3 Sledge 1u 22p 7801 220K BC847BW F852 H 4p7 3808 0V 7 6 2890 2891X 100n 0,2V 180p 2834 D CMFB 180p 2835 8 2x 0V 13 2,5V 12 0V 11 0V 10 1,4V 9 0,8V 8 1,3V H F835 H F836 RFFB Track- H F834 10 9 Focus- 3834 5K6 11 RFEQO 7 PWRON 2,4V 5K6 12 CDRW 4x 5 DIN 0,7V 6 GND 0V 3833 5K6 F833 13 Focus+ 3832 14 F832 VCC2 EQSEL 1x 47R H Track+ 2830 C F831 22u 15 2805 F830 H RGADJ 14 2837 9 1830 16 3809 from/to CD-drive 56K 10 +2.6V Vgap 2u2 3802 2800 B V/I 3 CFIL 0,8V 4 MON 0,2V 4n7 15K 3801 H 3804 V/I 2801 F850 3885 H13 3886 H14 3887 G14 3888 G15 3889 G14 {A1,A2,A3,A4,A5,A6,A7,A8,A9,A10,D0,D1,D2,D3,A0,RAS,WE,CAS} 1 LD F849 1,8V VCCL 2 2,5V 3800 +2.6V 4R7 3880 D11 3881 E11 3882 G12 3883 G12 3884 G13 3874 C5 3875 B4 3876 C4 3877 F7 3878 F7 DM 7800 TZA1024 F848 3868 F6 3869 G7 3871 F8 3872 F8 3873 F8 9 CD-PART A 3862 C10 3863 C10 3864 C10 3865 F9 3867 F5 8 VDDD1P 2,6V 1 2847 B5 2848 B5 2849 C5 2850 A9 2851 A9 SCLK 2832 E3 2833 E3 2834 E3 2835 E3 2836 E3 EF 2803 C4 2804 C5 2805 C2 2830 D1 2831 E2 3873 1830 B1 1840 E5 2800 A1 2801 B2 2802 B5 H D 13 14 15 4-2 4-2 CIRCUIT DIAGRAM - CONTROL/SUPPLY PART 1 2 2277 E8 2278 D8 2279 E8 2400 F15 2401 G12 2402 E10 2403 E10 2404 E10 2405 G12 2700 H14 3 3257 D6 3258 D2 3259 D2 3260 D6 3261 C4 3252 C6 3253 C3 3254 C5 3255 C5 3256 C7 2701 I14 2702 I15 3202 D5 3250 B7 3251 C2 3266 E4 3268 E8 3269 E8 3270 E2 3271 E1 4 3284 E1 3285 F1 3286 F1 3288 B7 3289 F8 3279 H2 3280 H2 3281 H3 3282 H2 3283 I2 5 3295 D6 3297 D5 3298 E3 3400 A14 3401 B14 3290 G8 3291 D8 3292 D8 3293 E4 3294 G4 6 3407 E10 3408 E10 3409 E10 3410 G12 3411 F15 3402 B14 3403 B15 3404 B14 3405 C14 3406 C14 7 3412 D15 3413 E15 3414 A15 3418 C15 3419 C15 3421 B14 3422 E10 3700 H15 3701 H14 3702 H15 8 3703 I15 3704 I15 3705 H15 3706 I14 3707 I14 3708 H15 3709 I14 3710 I14 3910 F8 5250 B6 5251 B7 6252 C2 6257 E2 6400 A13 7250 B7 9 7702 H14 F250 E1 F251 B1 F252 A1 F253 E1 7260 H3 7400 C10 7401 A14 7700 H15 7701 I15 7251 C6 7252 C2 7255 E2 7256 D4 7259 H2 10 F259 H5 F260 H5 F261 D1 F262 C5 F263 D9 F254 E2 F255 A8 F256 B8 F257 H4 F258 H5 11 F400 B11 F401 C13 F402 B13 F403 C13 F404 B14 12 13 F252 6 2250 4u7 40uH 3 2 1 F407 F411 F417 F419 F423 F415 F409 F421 F413 F438 F422 F408 F410 F424 F416 F418 F412 F414 F420 F400 F427 2,6V 2,6V 0V 33 10 LCD - DRIVER I/O PORT P1 12 13 15 16 31 2,6V P52 SEG21 30 2,0V P51 SEG22 29 P50 SEG23 28 1,6V P17 SEG24 SCK P16 SEG25 TXD/SO SEG26 P15 RXD/SI SEG27 P14 INT3 SEG28 P13 INT2 SEG29 P12 INT1 SEG30 P11 27 1,9V F434 F433 2401 2u2 F432 D DBB_ON 3412 SCL 100R 3413 26 1,8V SDA 100R 25 1,8V 24 2,6V PORES 23 2,6V 22 2,6V YMLD 21 0,3V RAB SEG31 P10 20 2,6V AVDD 19 2,6V VAREF 18 2,6V STOP5 P67 17 2,6V Key2 SILD 3411 +2.6V +AVDD 2400 1u TEMP BATT_LEVEL RESET 3705 R +A 3701R 4,5V 10M 3700 R 330K 7700R 2M2 BC857BW 7702 R 3708 BC847BW 2700 R 3702 R 10K R 1,3V 100n 1,4V 2M2 4,0V 0V 3709 R , R 7701 C R 330K 2701 BC847BW 3703 1n 1,9V 1M 4,4V 3706 R +VG 0V C ,R 10M 3704 3710 R +2.6V 3707 R 1M 2M2 2M2 * * Item 3701... 0 ohm for Non RC version {TEMP,ACCU,BATT_LEVEL,CHG_DET,RESET,WAKE,DM_PWM} 4 5 F 10R WAKE MCU_XIN RC # Item 3407 ... 150K ohm for ESP100 # Item 3409 ... 15k ohm for ESP45 & 12 5K6 ohm for ESP100 # Item 3422 ... 15K ohm ONLY for ESP45 & 12 ACCU WAKE RESET MUTE BEEP DM to AUDIO-PART to CD-PART to 1830 CD-PART from/to CD-drive Sledge DM+ DM- R....only for Cord R/C L ... only for DA23L C....only for charging version LN ... only for DA23LN X....component only provided (not in use) %....tolerance 1% 3 E NPC_RESET G F431 F425 6 Focus 5 OVERIDE Remote control Radial SL+ SL- 4 F430 SFSY +2.6V 10R Focus+ 3 C P53 SEG20 +AVDD Focus- 2 +2.6V ESD {C0,C1,C2,C3,S0,S1,S2,S3,S4,S5,S6,S7,S8,S9,S10,S11,S12,S13,Key1,Key2,S_MUTE,SLEEP,DC_IN} Track+ 1 4 F406 chg_on F435 32 0V P66 STOP4 P65 STOP3 P64 STOP2 14 1K P54 SEG19 LCD - DRIVER I/O PORT P5 11 3 2,6V 9 1,4V 8 P63 INT0 7 P62 ECNT 6 1,4V 5 1,8V 4 ESD-11H130 1 2 F405 P55 SEG18 P56 SEG17 P57 SEG16 0V 2,7V P70 SEG15 P71 SEG14 1,3V 1,3V S13 P72 SEG13 S12 P73 SEG12 1,3V S11 S10 1,3V P74 SEG11 P75 SEG10 1401 1 2 Key2 3 5 6 7 4 S0 S1 S2 9 10 8 S3 S4 S5 12 11 S6 1,3V S9 P76 SEG9 14 13 S7 S8 S9 S8 SEG7 P77 SEG8 1,3V 1,3V 16 17 15 S10 S7 S11 S12 S6 1,3V 1,3V SEG5 3 F260 to CD-part INNERSWITCH SEG6 18 19 2 3410 F259 Track- 7260C BC847BW ACCU TEMP 3283 C 470K 1250 B-ZR 2,6V BATT_LEVEL 3282 C 470K 0V 3281 47K F258 S13 1,3V S5 C3 C2 20 1 2,6V 13 P61 ECIN 2,2V 34 ADC INPUT I/O PORT P6 P60 OUT1A 12 PGND1 P2 STOP P20 INT5 3290 X 5K6 P2 RESET 64 0V SLEEP B 1402 3406 8 BIT A/D Converter 1,5V 14 PD03 P31 TC3 PD04 P32 TC4 PD06 P33 TC6 X 2273 1u 12 +A 15 62 1,5V 0V 16 P30 DV0 3,2V 17 61 1,3V 63 2,6V C 220p C0 2,6V 18 S_MUTE 60 1,5V 100n 2272 1u 19 220p 2268 35 RAM 2405 20 F437 36 DC_IN 21 2276 100n C1 VSS VC VG 2,2V OUT4B 22 VIN12 10n ERR2 CF2 CH2 MOTOR DRIVER 2275 ERR3 CF3 CH3 MOTOR DRIVER 2266 59 0,7V 0V ERR4 CF4 CH4 MOTOR DRIVER 1,5V SAW OE VR RST CF2 9 1,3V ERR1 CF1 10 CF1 1,3V CH1 ERR1 11 MOTOR DRIVER 0V 2,3V OUT1B SAW OE VR RST 4,4V VIN12 SAW OE VR RST VC VG SAW OE VR RST V1 0V 5K6 58 0,9V P22 XTOUT 100n 37 8-BIT-CPU P21 XTIN 2404 V2 2,6V 10K 16 3289 38 V3 VDD 3910 C ROM 2,6V # 39 LCD - DRIVER COM0 TEST # 3422 3409 15K 5K6 220p 40 COM1 0V 3408 12K 56 100n 2,6V 2403 57 100n 1,7V 41 TMP86C829 TMP86CH21 XOUT 2264 # 2402 42 3403 220K 3405 1K I/O PORT P7 1,1V 55 1,3V 43 BOOSTER CIRCUIT 1,3V S4 SEG3 COM2 54 1,3V 44 P3 CF3 6 SAW 220p 1,3V S3 53 1,3V C0 SEG4 22 21 23 COM3 C2 F436 1,3V 23 C1 C0 52 1,3V C1 45 F401 47K ESD ESD F403 ** 4,5V 7259C BC857BW 0V 2 C3 3407 150K 100n 1,3V 2263 2279 CF4 5 SAW GEN OSC SEG0 +2.6V 10K 3269 10K 2277 1u ERR4 4 OE 1,3V DC/DC CONVERTER 51 1,3V 3268 +VR VR 3 SAW GEN2 SEG1 SLEEP F428 46 1K F404 LCD - DRIVER 50 1,3V S0 XIN 0V CLK 0V OE 2,6V INM1 0,6V CGND RF1 1,6V VC 2,6V F263 S1 1,0V 3202 X 22K 2258 1u VOUT 0,3V 1u SEG2 +2.6V F257 1 3291 100K 49 1,3V 4,4V CONTROL VIN12 0V PGND4 CHGON 1,3V DTC RF1 INM1 3292 10K 2278 S2 ERR2 8 11 +A 470K 4,0V 48 SLEEP 1 CGHSW VC VIN VOUT VIN34 ACCU_IN DETECTION H S_MUTE +A 0V CONSTANT VOLTAGE CURRENT & BATTERY CHARGE CIRCUIT INM2 VIN34 24 47 ERR3 7 27 C2H 7,4V 100n VG +VG F429 26 VG 8,4V 3294 2269 25 OUT4A 470K 100n 2,2V G 270K 46 1,8V OUT2B 28 C1H 5,5V 45 RST 2267 3280 C +2.6V VIN VC VG 29 C1L 1,4V 44 0V PGND2 100n * Item 3270: 0 ohm for non-charging version 3279 C 2M2 VREF 1,2V DCIN 4,8V RESET 1M 43 1,2V OUT2A 10K 150K 3286 C VC VC VIN 30 C2L 1,2V 2265 +A 2259 10n 2260 100p WAKE 2 RF2 DCIN DETECT CHARGE PUMP * 31 VIN 4,4V 42 2,2V OUT3A F254 2R7 F DCIN VC 32 RSTB 2,6V 3270 C 41 RS BANDGAP REF. 4,4V VIN34 0V 3271C 2R7 F426 3298 C X 680R 40 VC VG 0V 39 VC 10K 0,4V 34 RS 0V 3293 C 33 CHGSW 0V 330R 3,8V t 3284 C 38 100p 7255 C BC868 +2.6V 37 36 RF2 3,4V 3266 35 INM2 2262 F250 ESD 3257 220K 3260 47 LCD VOLTAGE F262 VDET 2,6V 7256 SC111259FTA 6257 C SB140 F253 3256 2K7 3295 X 3259 220K 48 DC_IN 3255X 47K 3297 4K7 F261 DC JACK 2256 100u 0V 47K 3258 2261 100n 2255 1u +AVDD +2.6V 2257 4u7 7400 +1.25V 1252 7251 BC368 F256 10u 3254 3261 10K D 2,6V 7250 BC337-40 100R 7252 BC369 100K 0V 330R 0V PGND3 4,8V SB140 330p 4,4V 4n7 3252 DTC 0,2V C 2254 2,3V OUT3B 6252 +DC 3251 270R X 4,3V 3253 ESD Key1 5,0V 4,4V 3285X 3250 680R 5251 2252 5,0V TEMP. 2,5V 24 3404 F251 I 3414 3421 220K 1400 3288 10R A +2.6V 100K BC857BW F402 2253 22n Only for Ver.1 MCU-314011051321 4,3V 3400 BAS316 B E 1u 7401 4,4V 6400 5250 2251 1u F430 D15 F431 G14 F432 G13 F433 G12 F434 G12 15 1M F255 +A 4 630mA 391 F425 H10 F426 F1 F427 B13 F428 D8 F429 F4 2430 3430 1251 F420 B13 F421 B13 F422 B13 F423 B13 F424 B13 14 7430 BC847BW CONTROL / SUPPLY-PART A F415 B12 F416 B12 F417 B12 F418 B12 F419 B12 F410 B11 F411 B11 F412 B11 F413 B12 F414 B12 F405 C15 F406 C15 F407 B11 F408 B11 F409 B11 220K 2269 G4 2272 G5 2273 G6 2275 F8 2276 F8 2264 E7 2265 F4 2266 F8 2267 F4 2268 F8 Key1 2259 D7 2260 D6 2261 D1 2262 D4 2263 E8 2254 B6 2255 C7 2256 C7 2257 C8 2258 D5 3401 1402 B15 2250 A6 2251 A2 2252 B6 2253 B6 SPPB51 220K 3402 1250 H4 1251 A2 1252 D1 1400 B10 1401 B14 6 7 8 9 10 11 12 13 14 15 H I 4-3 4-3 CIRCUIT DIAGRAM - AUDIO PART 1300 B10 2301 A2 2302 C2 2303 B1 2304 D1 2305 B1 2306 D1 2313 C5 2314 C5 2315 B6 2316 D6 2319 B7 2320 D7 2321 B8 2322 D8 2325 C10 2326 C10 2332 C4 2333 E3 2335 E2 2339 E3 2340 C2 2341 B2 2342 C6 1 2343 E8 2344 C8 2345 B7 2346 D7 2894 D10 3311 B1 3318 C2 3320 C3 3323 B5 3324 D5 3326 B10 3327 B5 3312 C1 3313 B1 3314 D1 3315 B1 3316 D1 3317 A2 2 3328 D5 3333 C8 3334 E8 3337 A7 3338 D7 3339 B7 3 3340 D7 3341 B7 3342 D7 3343 B8 3344 D8 3345 B9 4 3346 D9 3347 B9 3348 C9 3349 B9 3350 D9 3360 C5 3361 C6 3362 C7 3364 D3 3365 E3 3366 E3 3367 E2 3375 B5 3376 C5 3377 B6 3378 D6 3379 C4 3380 B8 3368 E2 3370 B3 3371 B3 3372 C4 3373 C4 3374 C4 5 6 3381 D8 3382 C8 3383 C8 3384 B6 6300 C10 6301 E5 6302 C8 6303 C9 7300-A D2 7300-B B2 7301-A D7 7301-B B7 7 7302 C7 7303 B4 7304 C4 7305 C7 7306 E7 7308 C6 F302 D10 F304 C2 F305 B10 F306 B2 F307 B6 F308 D6 7309 B9 7310 D9 7311 B7 7831 B4 F105 D3 F301 B10 8 F309 C4 F310 E2 F311 E3 9 10 AUDIO-PART A V’ref A 2301 220p 3337 4K7 3317 3377 12K 2M2 +LF 5 10K 3311 4 LP 15K LEFT Channel 3313 LN 15K 220p 2303 2341 6 2305 100p 5 3315 10K 3327 4K7 7 4u7 7300-B 8 TC75W51FU +Audio 3370 470K DBB_ON F306 7831 BC857BW 3371 7303 BC817-40 F307 2x10K 220p C 1 3318 220p 2304 3316 10K D 100p 15K RIGHT Channel 3314 RN 15K 2306 RP A 3379 100K F304 2 2340 +LF 3 1 4u7 7300-A 8 TC75W51FU 2313 100n KILL 3360 47K 22R 3328 4K7 3378 12K 2M2 F308 Vref +Audio from CD-PART +Audio +2.6V F105 3364 3368 10K 3 BAS316 2326 2 100p 1 2344 1u A A +LF 3 2316 2346 X 100p 3340 2u2 56K 8 7301-A TDA1308T 1 2322 2 * 3346 V’ref BEEP 3366 100K 7306 BC847BW 2339 47u 1,3V 7310 BC817-40 6300R 2894 F302 220p 3350 D 15R 220u 4 2320 3344 330R A A 1 2 A 3 * 3345, 3346 change to 4R7 for /17 A 3334 100K 2343 A E A 4 5 6 7 ESD 3342 A A A 3381 10K 1u A A R...only for Cord R/C S...only for non Cord R/C X...component only provided (not in use) C A 3348 330R A 180K 2333 47u 2335 22u 100p 3333 100K 33p 3365 100K F311 3367 10K F310 Vref E 6301 BAV70 +LF 2325 3383 1K 3338 4K7 1300 Headphone 4 1K A 3324 3326 S A 6302 BAV70 6303 V’ref from CONTROL PART 3347 330R 3382 3362 6K8 B F305 18K MUTE +Audio 7305 BC847BW to CONTROL PART RC BC817-40 7309 A A F301 15R 3380 10K 3341 3361 3376 A 33p 3349 3343 330R A 2342 10n 3345 * 180K 7308 BC847BW 2314 100n 2321 220u 4 2319 3384 100K 7302 BC847BW from CONTROL PART 7301-B TDA1308T 7 6 7311 BC807-40 from CD-PART BC817-40 7304 A 56K 22R 2332 10u A 4 3374 100K 10K 5 4 10K 3312 3373 100K A 3372 2 2302 2u2 OVERIDE F309 3320 3 Vref 2315 2345 X 100p 3339 3375 470K from CD-PART B +LF A 8 BZX284-C10 3323 8 9 10 4-4 4-4 PCB LAYOUT DIAGRAM - COMPONENT SIDE 1 2 3 4 5 6 A A B B C C D D E E F F G G 1 2 3 4 5 6 1250 1251 1252 1300 1401 1402 1830 2254 2256 2258 2260 2262 2263 2264 2265 2266 2267 2268 2269 2272 2273 2301 2302 2303 2304 2305 2306 2313 2321 2322 2332 2333 2335 2339 2340 2341 2342 2802 2804 2830 2831 2837 2838 2843 2859 2885 2886 F3 C6 C6 F1 B2 D1 C2 E4 B5 E4 E4 F4 E3 E3 F4 E3 F4 E3 F4 F4 F3 F2 F3 F2 F3 F2 F3 F2 G4 G4 F3 E3 F3 F3 F2 E2 F3 B2 A2 C1 C2 C2 C2 C1 E3 E1 D1 2887 2892 2893 2894 3202 3252 3257 3260 3266 3295 3311 3312 3313 3314 3315 3316 3317 3318 3320 3327 3347 3348 3360 3361 3362 3370 3371 3372 3373 3374 3375 3376 3379 3382 3383 3384 3835 3837 3845 3846 3871 3872 3882 3883 3884 4206 4207 D2 E2 D2 E1 E4 E4 E4 E4 F4 E4 F3 F3 F2 F3 F2 F3 F2 F3 F2 F2 G4 G3 F3 G3 F3 F3 F3 F3 F3 F3 F3 F2 F3 G3 G3 F3 C2 C2 C1 C2 D3 D3 D3 D3 D3 E2 D2 4210 5250 5251 6252 6257 6300 6301 6302 6303 7250 7251 7252 7256 7300 7302 7303 7304 7308 7309 7310 7311 7831 7881 7883 D2 B6 A5 C6 C5 E1 G3 G3 G3 B5 B6 C5 F4 F3 G3 F3 F2 G3 G4 G4 G3 F3 E2 E2 4-5 4-5 PCB LAYOUT DIAGRAM - COPPER SIDE 1 2 3 4 5 6 A A B B C C D D E E F F G G For service testpoints see circuit diagram “CD-Part” 1 2 3 4 5 6 1400 1840 2250 2251 2252 2253 2255 2257 2259 2261 2275 2276 2277 2278 2279 2314 2315 2316 2319 2320 2325 2326 2343 2344 2345 2346 2400 2401 2402 2403 2404 2405 2430 2700 2701 2702 2800 2801 2803 2805 2832 2833 2834 2835 2836 2839 2840 A3 C4 C1 C1 B2 B2 B2 B2 E3 C1 F4 E3 E4 E3 E3 F5 F5 F5 F4 G4 E6 F5 G4 F5 F4 G4 C3 C2 B2 B2 B2 C2 B3 D3 C3 D3 B4 B4 B5 B4 C6 C5 B5 D5 D5 C5 C5 2841 2842 2844 2845 2846 2847 2848 2849 2850 2851 2852 2853 2854 2855 2856 2857 2858 2860 2861 2862 2880 2881 2882 2888 2889 2890 2891 3250 3251 3253 3254 3255 3256 3258 3259 3261 3268 3269 3270 3271 3279 3280 3281 3282 3283 3284 3285 C5 C5 C5 C5 B5 C5 C5 C5 D4 D4 E4 E4 D3 D3 D4 C4 C4 C4 D5 D4 D5 E4 E4 C4 D5 A4 A4 B2 C1 C2 C2 C2 E3 D2 D2 D3 E4 E4 C2 D2 D2 D2 D2 D2 D2 E2 D2 3286 3288 3289 3290 3291 3292 3293 3294 3297 3298 3323 3324 3326 3328 3333 3334 3337 3338 3339 3340 3341 3342 3343 3344 3345 3346 3349 3350 3364 3365 3366 3367 3368 3377 3378 3380 3381 3400 3401 3402 3403 3404 3405 3406 3407 3408 3409 D2 B2 E3 E3 B2 D3 D3 F3 E3 D2 F5 F5 E6 F5 F4 G4 F4 F4 F5 F5 F4 F4 G3 G4 G3 G4 F6 F5 E4 F4 E4 E4 E4 F4 F4 F4 G4 B2 B3 B3 B3 B3 B3 C3 A2 B2 B2 3410 3411 3412 3413 3414 3418 3419 3421 3422 3430 3700 3701 3702 3703 3704 3705 3706 3707 3708 3709 3710 3800 3801 3802 3803 3804 3805 3806 3807 3808 3809 3830 3831 3832 3833 3834 3836 3838 3839 3840 3841 3842 3843 3844 3847 3848 3849 C2 C3 C3 C3 C3 C4 C4 A2 B2 B4 D3 C3 D3 D3 D3 D3 E3 E3 D3 D3 D3 B4 B4 B4 A4 B5 A4 B5 B5 A4 A4 C6 B4 B4 B5 B5 C6 B5 D5 D5 D5 D5 C5 C5 C6 C5 C5 3850 3851 3852 3853 3854 3855 3856 3857 3858 3859 3860 3861 3862 3863 3864 3865 3867 3868 3869 3873 3874 3875 3876 3877 3878 3880 3881 3885 3886 3887 3888 3889 3890 3909 3910 4205 4208 5800 6400 7255 7259 7260 7301 7305 7306 7400 7401 C5 C5 D5 D4 D4 D4 E4 D4 D4 E4 C3 C3 D4 D4 D3 D3 C4 C4 C6 C4 C5 A4 A4 C4 C4 D5 D5 E4 D4 E4 E4 E4 D5 D5 E3 D5 F4 C4 B2 D2 D2 D2 F4 F4 G4 C3 B2 7430 7700 7701 7702 7800 7801 7830 7880 7882 B4 D3 D3 D3 B4 A5 C4 E5 D4 5-1 5-1 EXPLODED VIEW DESIGN "P" EXPLODED VIEW DESIGN "Q" 411 411 412 413 414 416 412 413 414 401 416 10 x SCREW B-1.4x3.5-NI 401 417 402 418 403 MECHANICAL PARTSLIST 419 404 421 406 422 407 (3x) 408 423 424 409 426 427 6 x SCREW P-1.7x9-CR 428 401 402 403 403 404 SEE TABLE 3103 304 70320 3103 307 99610 3103 307 99710 3103 301 06500 CD-DOOR-ASSY DOOR-BATTERY-2 CABINET - ASSY - 1 CABINET - ASSY - 2 SPRING-SLIDER-OPEN-2 406 407 408 411 414 3103 304 69580 3103 304 69570 3103 301 45180 SEE TABLE 3103 304 69510 SLIDER-OPEN SLIDER-RESUME SPRING-BATTERY-SHORT-2 PANEL-ASSY ZEBRASTRIP 416 3140 113 32640 416 417 418 421 422 3103 304 69680 3140 111 01110 3140 111 01150 3103 309 05320 3103 304 69590 MEMBRANE-KEYBOARD (AX21xx, AX51xx) MEMBRANE-KEYBOARD (AX71xx) CD-DOOR-SPRING-LEFT CD-DOOR-SPRING-RIGHT CD DA23LNPH DRIVE ASSY SUSPENSION 423 424 426 427 427 428 3103 301 45410 3103 301 45420 3103 301 45430 3103 307 99620 3103 307 99860 3103 304 70250 4822 462 41819 SPRING-BATTERY-MINUS SPRING-BATTERY-PLUS SPRING-BATTERY-CHARGE BOTTOM-ASSY-1 (not for /17) BOTTOM-ASSY-1 (only for /17) BELT CLIP RUBBER FOOT TYPE NO. COLOUR 403 411 DOOR-CD ASSY CABINET ASSY PANEL ASSY 401 Translucent blue 3140 117 62760 3103 307 99610 3140 117 62110 AX2101 AX2102 Silver 3140 117 62770 3103 307 99710 3140 117 61730 Black 3140 117 62100 3103 307 99710 3140 117 61730 AX2100 AX5100 AX5101 AX5102 Silver 3140 117 62880 3103 307 99710 3140 117 62110 AX5103 Red 3140 117 61720 3103 307 99710 3140 117 61730 AX5104 Silver 3140 117 62880 3103 307 99710 3140 117 62110 AX5111 Translucent blue 3140 117 62820 3103 307 99610 3140 117 62110 AX5112 Silver 3140 117 62830 3103 307 99710 3140 117 61730 AX5113 Red 3140 117 61720 3103 307 99710 3140 117 61730 AX5114 Red 3140 117 61720 3103 307 99710 3140 117 61730 AX5115 Translucent blue 3140 117 62820 3103 307 99610 3140 117 62110 AX5116 Red 3140 117 61720 3103 307 99710 3140 117 61730 AX5117 Green 3140 117 63340 3103 307 99710 3140 117 61730 AX5118 Black 3140 117 62100 3103 307 99710 3140 117 61730 AX7101 AX7104 AX7113 Black Rose 3140 117 61740 3103 307 99710 3140 117 61750 6-1 ELECTRICAL PARTSLIST - MISCELLANEOUS - 1003 1003 - CAPACITORS - 1250 1251 1252 3140 110 51310 3103 308 84250 2422 025 12272 2422 086 10946 2422 026 05086 LCD PANEL (AX21../AX51..) LCD PANEL (AX71..) CONN. 6P, CD DRIVE FUSE 630MA 65VA DC SOCKET 2316 2319 2320 2321 2322 4822 126 14491 2222 867 15339 2222 867 15339 4822 124 12245 4822 124 12245 2.2µF 20% 10V 33pF 5% NP0 50V 33pF 5% NP0 50V 220µF 20% 10V 220µF 20% 10V 1300 1300 1400 1401 1402 2422 026 05204 2422 026 05203 4822 265 11248 4822 276 12889 2422 127 00545 SOCKET-HEADPHONE SOCKET-H/P (RC) CONN. 24P, MEMBRANE SWITCH, CD DOOR SWITCH-SLIDE 2325 2326 2332 2333 2335 4822 122 31765 4822 122 31765 4822 124 11947 4822 124 12362 4822 124 40998 100pF 2% NP0 63V 100pF 2% NP0 63V 10µF 20% 16V 47µF 20% 4V 22µF 20% 6,3V 1830 4822 267 11028 CONN. 16P, CD DRIVE 2339 2340 2341 2342 2343 4822 124 12362 4822 124 22726 4822 124 22726 5322 126 11583 3198 017 41050 47µF 20% 4V 4,7µF 20% 35V 4,7µF 20% 35V 10nF 10% X7R 50V 47nF 10% X7R 16V - CAPACITORS - 2250 2251 2252 2253 2254 2020 552 96305 3198 017 41050 4822 126 14241 4822 126 14494 4822 126 13193 4,7µF +80-20% Y5V 10V 47nF 10% X7R 16V 330pF 5% NPO 50V 22nF 10% X7R 25V 4,7nF 10% X7R 63V 2344 2400 2401 2402 2403 3198 017 41050 3198 017 41050 4822 126 14491 4822 126 14305 4822 126 14305 47nF 10% X7R 16V 47nF 10% X7R 16V 2.2µF 20% 10V 100nF 10% X7R 16V 100nF 10% X7R 16V 2255 2256 2257 2258 2259 3198 017 41050 4822 124 12248 2020 552 96305 3198 017 41050 5322 126 11583 47nF 10% X7R 16V 100µF 20% 4V 4,7µF +80-20% Y5V 10V 47nF 10% X7R 16V 10nF 10% X7R 50V 2404 2405 2700 2701 2702 4822 126 14305 4822 126 14305 4822 126 14305 5322 126 11578 5322 126 11583 100nF 10% X7R 16V 100nF 10% X7R 16V 100nF 10% X7R 16V 1nF 10% X7R 50V 10nF 10% X7R 50V 2260 2261 2262 2263 2264 4822 122 31765 4822 126 14305 4822 122 31765 4822 126 13883 4822 126 13883 100pF 2% NP0 63V 100nF 10% X7R 16V 100pF 2% NP0 63V 220pF 5% 50V 220pF 5% 50V 2800 2801 2802 2803 2804 4822 126 14491 4822 126 13193 4822 124 40998 4822 126 14305 4822 124 12362 2.2µF 20% 10V 4,7nF 10% X7R 63V 22µF 20% 6,3V 100nF 10% X7R 16V 47µF 20% 4V 2265 2266 2267 2268 2269 4822 126 14305 4822 126 13883 4822 126 14305 4822 126 13883 4822 126 14305 100nF 10% X7R 16V 220pF 5% 50V 100nF 10% X7R 16V 220pF 5% 50V 100nF 10% X7R 16V 2805 2830 2831 2832 2833 4822 126 14305 4822 124 40998 4822 126 14508 4822 126 14241 4822 126 14508 100nF 10% X7R 16V 22µF 20% 6,3V 180pF 5% 50V 330pF 5% NPO 50V 180pF 5% 50V 2272 2275 2276 2277 2278 3198 017 41050 5322 126 11583 4822 126 14305 3198 017 41050 3198 017 41050 47nF 10% X7R 16V 10nF 10% X7R 50V 100nF 10% X7R 16V 47nF 10% X7R 16V 47nF 10% X7R 16V 2834 2835 2836 2837 2838 4822 126 14508 4822 126 14508 4822 126 14508 4822 126 13883 4822 126 13883 180pF 5% 50V 180pF 5% 50V 180pF 5% 50V 220pF 5% 50V 220pF 5% 50V 2279 2301 2302 2303 2304 4822 126 14305 4822 126 13883 4822 126 13883 4822 126 13883 4822 126 13883 100nF 10% X7R 16V 220pF 5% 50V 220pF 5% 50V 220pF 5% 50V 220pF 5% 50V 2839 2840 2841 2842 2843 4822 126 13883 4822 126 13883 4822 126 13883 4822 126 13883 4822 124 40998 220pF 5% 50V 220pF 5% 50V 220pF 5% 50V 220pF 5% 50V 22µF 20% 6,3V 2305 2306 2313 2314 2315 4822 122 31765 4822 122 31765 4822 126 14305 4822 126 14305 4822 126 14491 100pF 2% NP0 63V 100pF 2% NP0 63V 100nF 10% X7R 16V 100nF 10% X7R 16V 2.2µF 20% 10V 2844 2845 2846 2847 2848 4822 126 14305 3198 017 34730 5322 126 11578 4822 126 14494 4822 126 11669 100nF 10% X7R 16V 47nF 10% X7R 16V 1nF 10% X7R 50V 22nF 10% X7R 25V 27pF 5% 50V 6-2 ELECTRICAL PARTSLIST - CAPACITORS - - RESISTORS - 2849 2850 2851 2852 2853 5322 126 11583 5322 126 11579 5322 126 11579 5322 126 11579 4822 126 14247 10nF 10% X7R 50V 3,3nF10% X7R 63V 3,3nF10% X7R 63V 3,3nF10% X7R 63V 1,5nF 5% X7R 50V 3284 3286 3288 3289 3291 2322 615 13103 4822 051 30103 4822 051 30109 4822 051 30562 4822 117 13632 NTC 10K 5% 0,21W 10K 5% 0,062W 10R 5% 0,062W 5,6K 5% 0,063W 100K 1% 0,062W 2854 2855 2856 2857 2858 4822 126 14247 5322 126 11579 4822 126 14549 4822 126 14305 4822 126 13344 1,5nF 5% X7R 50V 3,3nF10% X7R 63V 33nF 5% 16V 100nF 10% X7R 16V 1,5nF 5% 63V 3292 3293 3294 3297 3298 4822 051 30103 4822 051 30331 4822 051 30474 4822 051 30472 4822 051 30681 10K 5% 0,062W 330R 5% 0,062W 470K 5% 0,062W 4,7K 5% 0,062W 680R 5% 0,062W 2859 2860 2861 2862 2880 4822 124 12362 4822 126 13344 3198 017 41050 3198 017 41050 4822 126 14305 47 µF 20% 4V 1,5nF 5% 63V 47nF 10% X7R 16V 47nF 10% X7R 16V 100nF 10% X7R 16V 3311 3312 3313 3314 3315 4822 051 30153 4822 051 30153 4822 051 30153 4822 051 30153 4822 051 30103 15K 5% 0,062W 15K 5% 0,062W 15K 5% 0,062W 15K 5% 0,062W 10K 5% 0,062W 2881 2882 2885 2886 2887 4822 126 14305 4822 126 14305 4822 126 14305 4822 124 40998 4822 126 14549 100nF 10% X7R 16V 100nF 10% X7R 16V 100nF 10% X7R 16V 22µF 20% 6,3V 33nF 5% 16V 3316 3317 3318 3320 3323 4822 051 30103 4822 051 30103 4822 051 30103 3103 308 53680 4822 051 30123 10K 5% 0,062W 10K 5% 0,062W 10K 5% 0,062W POTMETER 2X10K CX2 12K 5% 0,062W 2888 2889 2890 2892 2893 4822 126 14305 4822 122 33741 4822 126 13887 4822 126 14305 4822 126 14549 100nF 10% X7R 16V 10pF 10% NP0 50V 4,7pF 1% 50V 100nF 10% X7R 16V 33nF 5% 16V 3324 3326 3327 3328 3333 4822 051 30123 4822 051 30008 4822 051 30472 4822 051 30472 4822 117 13632 12K 5% 0,062W 0R JUMPER 0603 4,7K 5% 0,062W 4,7K 5% 0,062W 100K 1% 0,062W 2894 4822 126 13883 220pF 5% 50V 3334 3337 3338 3339 3340 4822 117 13632 4822 051 30472 4822 051 30472 4822 051 30563 4822 051 30563 100K 1% 0,062W 4,7K 5% 0,062W 4,7K 5% 0,062W 56K 5% 0,062W 56K 5% 0,062W - RESISTORS - 3250 3252 3253 3254 3256 4822 051 30681 4822 051 30331 4822 051 30101 4822 117 12925 4822 051 30272 680R 5% 0,062W 330R 5% 0,062W 100R 5% 0,062W 47K 1% 0,063W 2,7K 5% 0,062W 3341 3342 3343 3344 3345 4822 051 30184 4822 051 30184 4822 051 30331 4822 051 30331 4822 117 12971 180K 5% 0,062W 180K 5% 0,062W 330R 5% 0,062W 330R 5% 0,062W 15R 5% 0,062W 3257 3258 3259 3260 3261 4822 117 12891 4822 117 13632 4822 117 12891 4822 051 30105 4822 051 30103 220K 1% ERJ3E 100K 1% 0,062W 220K 1% ERJ3E 1M 5% 0,062W 10K 5% 0,062W 3346 3347 3348 3349 3350 4822 117 12971 4822 051 30331 4822 051 30331 4822 051 30008 4822 051 30008 15R 5% 0,062W 330R 5% 0,062W 330R 5% 0,062W 0R JUMPER 0603 0R JUMPER 0603 3266 3268 3269 3270 3271 4822 051 30103 4822 051 30103 4822 051 30103 2322 702 70278 2322 702 70278 10K 5% 0,062W 10K 5% 0,062W 10K 5% 0,062W 2,7R 5% RC21 2,7R 5% RC21 3360 3361 3362 3364 3365 4822 117 12925 4822 051 30183 4822 051 30682 4822 051 30008 4822 117 13632 47K 1% 0,063W 18K 5% 0,062W 6,8K 5% 0,062W 0R JUMPER 0603 100K 1% 0,062W 3279 3280 3281 3282 3283 3198 021 32250 4822 051 30474 4822 117 12925 4822 051 30474 4822 051 30474 2,2M 5% 470K 5% 0,062W 47K 1% 0,063W 470K 5% 0,062W 470K 5% 0,062W 3366 3367 3368 3370 3371 4822 117 13632 4822 051 30103 4822 051 30103 4822 051 30474 4822 051 30474 100K 1% 0,062W 10K 5% 0,062W 10K 5% 0,062W 470K 5% 0,062W 470K 5% 0,062W 6-3 ELECTRICAL PARTSLIST - RESISTORS - - RESISTORS - 3372 3373 3374 3375 3376 4822 051 30103 4822 117 13632 4822 117 13632 4822 117 12139 4822 117 12139 10K 5% 0,062W 100K 1% 0,062W 100K 1% 0,062W 22R 5% 0,062W 22R 5% 0,062W 3809 3830 3831 3832 3833 4822 051 30563 4822 051 30109 4822 051 30562 4822 051 30562 4822 051 30562 56K 5% 0,062W 10R 5% 0,062W 5,6K 5% 0,063W 5,6K 5% 0,063W 5,6K 5% 0,063W 3377 3378 3379 3380 3381 3198 021 32250 3198 021 32250 4822 117 13632 4822 051 30103 4822 051 30103 2,2M 5% 2,2M 5% 100K 1% 0,062W 10K 5% 0,062W 10K 5% 0,062W 3834 3835 3836 3837 3838 4822 051 30562 4822 051 30273 4822 051 30273 4822 051 30333 4822 051 30333 5,6K 5% 0,063W 27K 5% 0,062W 27K 5% 0,062W 33K 5% 0,062W 33K 5% 0,062W 3382 3383 3384 3400 3401 4822 051 30102 4822 051 30102 4822 117 13632 4822 117 13632 4822 117 12891 1K 5% 0,062W 1K 5% 0,062W 100K 1% 0,062W 100K 1% 0,062W 220K 1% ERJ3E 3839 3840 3841 3842 3843 4822 051 30333 4822 051 30333 4822 051 30103 4822 051 30103 4822 051 30103 33K 5% 0,062W 33K 5% 0,062W 10K 5% 0,062W 10K 5% 0,062W 10K 5% 0,062W 3402 3403 3404 3405 3406 4822 117 12891 4822 117 12891 4822 051 30102 4822 051 30102 4822 051 30102 220K 1% ERJ3E 220K 1% ERJ3E 1K 5% 0,062W 1K 5% 0,062W 1K 5% 0,062W 3844 3845 3846 3847 3848 4822 051 30103 4822 051 30103 4822 051 30103 4822 051 30339 4822 051 30333 10K 5% 0,062W 10K 5% 0,062W 10K 5% 0,062W 33R 5% 0,062W 33K 5% 0,062W 3407 3408 3409 3409 3410 4822 051 30154 4822 051 30123 4822 051 30153 4822 051 30562 4822 051 30109 150K 5% 0,062W 12K 5% 0,062W 15K 5% 0,062W 5,6K 5% 0,062W 10R 5% 0,062W 3849 3850 3851 3852 3853 4822 051 30102 4822 051 30223 4822 051 30102 4822 051 30109 4822 051 30109 1K 5% 0,062W 22K 5% 0,062W 1K 5% 0,062W 10R 5% 0,062W 10R 5% 0,062W 3411 3412 3413 3414 3418 4822 051 30109 4822 051 30101 4822 051 30101 4822 117 12925 4822 051 30008 10R 5% 0,062W 100R 5% 0,062W 100R 5% 0,062W 47K 1% 0,063W 0R JUMPER 0603 3854 3855 3856 3857 3858 4822 051 30222 4822 051 30222 4822 051 30222 4822 051 30222 4822 051 30222 2,2K 5% 0,062W 2,2K 5% 0,062W 2,2K 5% 0,062W 2,2K 5% 0,062W 2,2K 5% 0,062W 3421 3422 3700 3701 3702 4822 117 12891 4822 051 30153 3198 021 32250 4822 051 30334 3198 021 32250 220K 1% ERJ3E 15K 5% 0,062W 2,2M 5% 330K 5% 0,062W 2,2M 5% 3859 3860 3861 3862 3863 4822 051 30222 4822 051 30103 4822 051 30103 4822 051 30103 4822 051 30103 2,2K 5% 0,062W 10K 5% 0,062W 10K 5% 0,062W 10K 5% 0,062W 10K 5% 0,062W 3703 3704 3707 3708 3709 4822 051 30105 4822 051 30105 3198 021 32250 4822 051 30103 4822 051 30334 1M 5% 0,062W 1M 5% 0,062W 2,2M 5% 10K 5% 0,062W 330K 5% 0,062W 3864 3865 3867 3868 3869 4822 051 30103 4822 051 30332 4822 117 12139 4822 117 12139 4822 051 30479 10K 5% 0,062W 3,3K 5% 0,062W 22R 5% 0,062W 22R 5% 0,062W 47R 5% 0,062W 3710 3800 3801 3802 3803 3198 021 32250 4822 117 13608 4822 051 30153 4822 051 30683 4822 051 30332 2,2M 5% 4,7R 5% 0,0016W 15K 5% 0,062W 68K 5% 0,062W 3,3K 5% 0,062W 3871 3872 3873 3874 3875 4822 051 30008 4822 051 30008 4822 051 30008 4822 051 30105 4822 051 30472 0R JUMPER 0603 0R JUMPER 0603 0R JUMPER 0603 1M 5% 0,062W 4,7K 5% 0,062W 3804 3805 3806 3807 3808 4822 051 30479 4822 051 30472 4822 051 30332 4822 051 30471 4822 117 12891 47R 5% 0,062W 4,7K 5% 0,062W 3,3K 5% 0,062W 470R 5% 0,062W 220K 1% ERJ3E 3878 3880 3882 3883 3884 4822 051 30008 4822 117 12139 4822 051 30008 4822 051 30008 4822 051 30008 0R JUMPER 0603 22R 5% 0,062W 0R JUMPER 0603 0R JUMPER 0603 0R JUMPER 0603 # 6-4 ELECTRICAL PARTSLIST - RESISTORS - - IC & TRANSISTORS - 3885 3886 3887 3888 3890 4822 051 30103 4822 051 30103 4822 117 12139 4822 117 13632 4822 117 12139 10K 5% 0,062W 10K 5% 0,062W 22R 5% 0,062W 100K 1% 0,062W 22R 5% 0,062W 7250 7251 7252 7255 7256 9322 003 64676 5322 130 44647 5322 130 44593 5322 130 61569 9322 171 12671 TBC337-40 BC368 BC369 BC868 SC111259AFTA 3909 3910 4205 4206 4207 4822 051 30008 4822 051 30103 4822 051 30008 4822 051 30008 4822 051 30008 0R JUMPER 0603 10K 5% 0,062W 0R JUMPER 0603 0R JUMPER 0603 0R JUMPER 0603 7259 7260 7300 7301 7302 5322 130 42756 3198 010 42310 9322 142 72685 4822 209 33165 3198 010 42310 BC857C BC847BW TC75W51FU TDA1308T/N1 BC847BW 4208 4210 4822 051 30008 4822 051 10008 0R JUMPER 0603 0R JUMPER 1206 7303 7304 7305 7306 7308 4822 130 42615 4822 130 42615 3198 010 42310 3198 010 42310 3198 010 42310 BC817-40 BC817-40 BC847BW BC847BW BC847BW IND VAR 40µH 10µH 10% LAL04T 100µH RES CER 33.868MHz 7309 7310 7311 7400 7401 4822 130 42615 4822 130 42615 5322 130 60123 3140 110 51521 5322 130 42756 BC817-40 BC817-40 BC807-40 TMP86CH21F-FOCUS BC857C 7700 7701 7702 7800 7801 5322 130 42756 3198 010 42310 3198 010 42310 4822 209 17286 3198 010 42310 BC857C BC847BW BC847BW TZA1024T/N1 BC847BW 7830 7831 7880 7881 7882 9352 641 80557 5322 130 42756 9322 169 78671 9322 175 89668 3198 010 42310 SAA7324H/M2B BC857C SM5907AF MSM51V17405F-60SJ BC847BW - COILS & FILTERS - 5250 5251 5800 1840 2422 536 00346 4822 157 51462 4822 157 11074 2422 540 98555 - DIODES - 6252 6257 6300 6301 6302 5322 130 81917 5322 130 81917 4822 130 11551 5322 130 34331 5322 130 34331 SB140 SB140 UDZS10B BAV70 BAV70 6303 6400 4822 130 11397 4822 130 11397 BAS316 BAS316 Note: Only these parts mentioned in the list are normal service parts.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Page Count : 24 Page Mode : UseThumbs Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:92bd62d0-0e7f-4001-a3b5-412f98c213b3 Producer : Acrobat Distiller 4.0 for Macintosh Modify Date : 2006:01:25 08:32:58Z Create Date : 2001:12:11 12:24:38Z Metadata Date : 2006:01:25 08:32:58Z Document ID : uuid:29f89697-4432-4bd5-8356-784fb100a62d Format : application/pdfEXIF Metadata provided by EXIF.tools