S.G_TM4060_BOOK Travel Mate 4060 Travelmate

4060 to the manual b06535fc-05c6-4880-a76e-defa7cc26f5f

User Manual: TravelMate 4060

Open the PDF directly: View PDF PDF.
Page Count: 99

TravelMate 4060 Series
Service Guide
PRINTED IN TAIWAN
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
II
Revision History
Please refer to the table below for the updates made on TravelMate 4060 service guide.
Date Chapter Updates
200512/27 Chapter 1 Revise memory specification to 533MHz on page 19.
2006/01/17 Chapter 1 Update LCD panel specification on page 25.
2006/02/15 Chapter 3 Revise disassembling SOP on chapter 3.
2006/9/18 Chapter 6 Revise touchpad board to main board FFC part number.
III
Copyright
Copyright © 2005 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
IV
Conventions
The following conventions are used in this manual:
SCREEN MESSAGES Denotes actual messages that appear
on screen.
NOTE Gives bits and pieces of additional
information related to the current
topic.
WARNING Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT Reminds you to do specific actions
relevant to the accomplishment of
procedures.
V
Preface
Before using this information and the product it supports, please read the following general information.
1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
VI
VII
Chapter 1 System Introduction 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Closed front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Left view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Right view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Bottom view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Easy-Launch Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Using the keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Lock keys and embedded numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Touchpad basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Chapter 2 System Utilities 28
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Navigating the BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
BIOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Create Crisis Recovery Diskette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Recover BIOS from Crisis Recovery Diskette . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Chapter 3 Machine Disassembly and Replacement 42
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Disassembly Procedure Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Removing the HDD Module/the Memory and the Wireless LAN Card/
the Thermal Module and the CPU/ODD Module and LCD Module . . . . . . . . . . . . . .47
Removing the HDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Removing the Memory and the Wireless LAN Card . . . . . . . . . . . . . . . . . . . . . .47
Removing the Thermal Module and CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Removing the ODD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Removing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Disassembling the Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Separate the Main Unit Into the Upper and the Lower Case Assembly . . . . . . .51
Disassembling the Upper Case Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Disassembling the Lower Case Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Table of Contents
VIII
Disassembling the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Disassembling the External Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Disassembling the HDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Disassembling the Optical Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Chapter 4 Troubleshooting 58
System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
External Diskette Drive Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
External CD-ROM Drive Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Keyboard or Auxiliary Input Device Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Memory check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Power System Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Touchpad Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Power-On Self-Test (POST) Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Index of Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Phoenix BIOS Beep Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Index of Symptom-to-FRU Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Chapter 6 FRU (Field Replaceable Unit) List 76
TravelMate 4060 Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Please notice that Chapter 5 has been combined to Chapter 1.
Table of Contents
IX
Chapter 1 1
Features
This computer was designed with the user in mind. Here are just a few of its many features:
Platform
TIntel® Pentium® M 730/740/750/760/770/780 processor (2MB L2 cache, 1.60/1.73/1.86/2/2.13/
2.26 GHz, 533 MHz FSB)
TIntel® Pentium® M 725 processor (2MB L2 Cache, 1.60 GHz, 400 MHz FSB)
TIntel Celeron M processor 360/370/380 (1 MB L2 cache, 1.40/1.50/1.60 GHz, 400 MHz FSB)
TChipset: Intel® 915GM
Memory
T256 MB/512 MB of DDRII 533 memory, upgradeable to 2 GB with dual so DIMM modules
Data storage
T40/60/80/100 GB ATA/100 hard disk
TDVD-Dual double-layer drive
TDVD/CD-RW combo drive
Display and graphics
TColor Thin-Film Transistor (TFT) LCD displaying at
-- 15” XGA (1024 X 768)
-- 15.4” WXGA (1280 X 800) supporting simultaneous multi-window viewing on dual displays via
Acer GridVista
TIntel® 915GM integrated 3D graphics, featuring Intel Graphics Media Accelerator 900 and up to
128 MB of shared memory
TMicrosoft® DirectX® 7.0 and dual independent display support
TMPEG-2/DVD hardware-assisted capability
TSimultaneous LCD and CRT display with LCD panel resolution at 70 Hz
Communication
TModem: 56K ITU V.92 modem with PTT approval; Wake-on-Ring ready
TLAN: 10/100 Mbps Fast Ethernet; Wake-on-LAN ready
TWireless LAN (optional): integrated miniPCI Acer InviLinkTM 802.11b/g Wi-Fi CERTIFIEDTM
solution
TAcer SignalUP wireless technology support
TWireless PAN (optional): integrated Bluetooth®
Audio
TAudio system with two built-in speakers
TSound Blaster ProTM and MS-Sound compatible
TBuilt-in microphone
System Introduction
Chapter 1
2TravelMate 4060
Input devices
T88-/89-key Acer FineTouchTM keyboard
TTouchpad with 4-way integrated scroll button
TFour easy-launch buttons
TTwo front-panel buttons: wireless LED-button and Bluetooth® LED-button
I/O interface
TThree USB 2.0 ports
TEthernet (RJ-45) port
TModem (RJ-11) port
TExternal display (VGA) port
TMicrophone
TLine-in jack
THeadphones/speaker/line-out port
TOne Type II PC Card slot
TDC-in jack for AC adaptor
Chapter 1 3
System Block Diagram
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
INTEL Mobile_479 CPU
DDR-II
ATA 66/100
HD Audio
AUDIO CODEC
DDR-II SODIMM1
DDR-II SODIMM2
IDE-ODD
PATA HDD
ATA 66/100
RJ11
Page: 19
Page: 16
Page: 16
Page: 10
CLOCK GEN
ICS954206
Page:2, 3
Page: 5, 6 , 7, 8
Page: 12 , 13 , 14
Page:4
LINE OUT
INTEL
ALVISO 915GM
NB
SB
DMI I/F
Page: 21
Page: 22Page: 22
Touchpad
KBC
NS
PC97551
Keyboard
INTEL
ICH6-M
CELERON-M/PENTIUM-M
PCI BUS 33MHZ
RJ45
REALTEK
RTL8100CL
USB 2.0
Page: 18
Page: 17
MINI-PCI
Wireless LAN
Realtek
Page: 20
ALC260 (ALC883)
SPEAKER
HOST BUS 533/400MHZ
LPC 33MHZ
TI PCMCIA
PCI1510A ( L-F )
+1.8VSUS
+1.8V
TM4060/AS1640(ZL8 for Quanta project code)
REQ2# / GNT2#
REQ1# / GNT1#
AD20
AD17
INTB# , INTD#
INTC#
Page: 10
Page: 21
FLASH
Page: 22
FAN
CPU CORE
CRT
Page: 11
RGB
LVDS
Page: 11
LVDS
BATTERY CHARGER
TYPE II
SLOT
Page: 18
MIC IN
+1.05V
+2.5V
Bluetooth
USB
interface
USB4 Page:16
USB2,3,5
SYSTEM
USB PORT *3
MODEMAMP
MAX9755
AD24
REQ0# / GNT0#
INTA#
Page: 16
MINI-PCIE slot
Wireless LAN
(Option)
PCI-E BUS
Page:23
SENTECH
SC451ITSTR
SYSTEM 3V/5V
MAXIM
MAX1999
Page:24
+1.5V
SENTECH
SC1470
SI9183-AD
+1.5V_S5
SENTECH
SC1565
SENTECH
SC4215
Page:25
MAXIM
MAX8724
Page:26
Page: 16
Page: 17
Page:16
Page: 19
Page: 19 Page: 20 Page: 20 Page: 17
+3VPCU
+3V_S5/+3VSUS
+3V
+5VPCU
+5VSUS
+5V
+15V
ON
NCP5214
+0.9VSUS
+0.9V
BLOCK DIAGRAM
3A
126Tuesday, August 09, 2005
Size Document Number Rev
Date: Sheet of
Acer Incorporated
PROJECT:Lugano II
4TravelMate 4060
Board Layout
Top View
Chapter 1 5
Bottom View
1 SW1 Lid Switch 2 CN1 LCD Connector
3 CN2 Launch Board Connector 4 CN3 Modem Connector
5 CN7 Keyboard Connector 6 CN4 Bluetooth Module Connector
7 CN5 Touchpad Board Connector 8 CN6 Internal Microphone Connector
9 U17 Clock Generator 10 U4 PCMCIA Connector
11 CN9 MDC Connector 12 CN11 Internal Speaker Connector
13 CN13 Power Jack 14 CN12 CRT Connector
15 CN14 Battery Connector 16 CN15 Optical Disk Drive Connector
17 CN17 RJ45 & RJ11 Connector 18 CN26 Wireless LAN Controller
19 U11 North Bridge 20 U13 CPU Socket
6TravelMate 4060
21 CN20 USB Connector 22 CN21 USB Connector
23 U19 BIOS ROM 24 U4 EC PC97551 (Power and I/O
Connector)
25 CN22 RTC Battery 26 CN18 Memory Socket 1
27 U1 LAN Chipset RTL8100CL 28 CN19 Memory Socket 2
29 U18 South Bridge 30 CN24 PCMCIA Connector
31 CN25 HDD Connector 32 CN27 USB Connector
33 CN28 Line-out/SPEDIF Jack 34 CN29 Microphone Jack
35 CN30 Line-in Jack 36 SW3 WLAN Button
37 SW2 Bluetooth Button 38 LED2 Charger LED
39 LED1 Power LED 40 U22 Audio Codec
41 U10 Fan Connector
Chapter 1 7
Panel
This is a brief introduction to the I/O ports, the features and the indicators.
Front view
#Item Description
1 Display screen Also called LCD (Liquid Crystal Display), displays computer
output.
2 Microphone Internal microphone for sound recording.
3 Keyboard For entering data into you computer.
4 Palmrest Comfortable support area for your hands when you use the
computer.
5 Click buttons (Left, center and right) The left and right buttons function like the left and right
mouse buttons; the center button serves as a 4-way scroll
button.
6 Touchpad Touch-sensitive pointing device which functions like a
computer mouse.
7 Status indicators LEDs (Light Emitting Diodes) that turn on and off to show
the status of the computer and its functions and
components.
8 Easy-Launch buttons Buttons for launching frequently used programs.
9 Power button Turns the computer on and off.
8TravelMate 4060
Closed front view
Left view
#Icon Item/ Port Description
1 Speakers Left and right speakers deliver stereo audio
output.
2 Power indicator Lights up when the computer is on.
3 Battery indicator Lights up when the battery is being charged.
4 Bluetooth communication button/
indicator
Press to enable/disable the Bluetooth function.
Indicates the status of Bluetooth communication
(optional).
5 Wireless communication button/
indicator
Press to enable/disable the wireless function.
Indicates the status of wireless LAN
communication (optional).
6 Line-in jack Accepts audio line-in devices (e.g., audio CD
player, stereo walkman).
7 Microphone jack Accepts inputs from external microphones.
8 Speaker/Line-Out/Headphone jack Connects to audio line-out devices (e.g.,
speakers, headphones).
9 USB 2.0 port Connects to Universal Serial Bus (USB) 2.0
devices (e.g., USB mouse, UsB camera).
# Item Description
# Item Description
Chapter 1 9
Right view
Rear view
#Icon Item/ Port Description
1 Optical drive Internal optical drive; accepts CDs or DVDs
depending on the optical drive type.
2 LED indicator Lights up when the optical drive is active.
3 Optical drive eject button Ejects the optical drive tray from the drive.
4 Emergency eject hole Ejects the optical drive tray when the computer is
turned off.
#Icon Item/ Port Description
1 PC Card slot eject button Ejects the PC Card from the slot
2 PC card slot Accepts one Type II CardBus PC Card.
3 Two USB 2.0 ports Connects to Universal Serial Bus (USB) 2.0
devices (e.g., USB mouse, USB camera).
4 Network jack Connects to an Ethernet 10/100 based
network.
5 Modem jack Connects to a phone line.
6 Ventilation slots Enable the computer to stay cool, even after
prolonged use.
10 TravelMate 4060
Bottom view
#Icon Port Description
1 Power jack Connects to an AC adaptor.
2 External display port Connects to a display device (e.g., external
monitor, LCD projector).
3 Security keylock Connects to a Kensington-compatible
computer security lock.
#Item Description
1 Hard disc bay Houses the computer’s hard disc (secured by a screw).
2 Battery release latch Unlatches the battery to remove the battery pack.
3 Battery bay Houses the computer’s battery pack.
4 Battery lock Locks the battery in place.
5 Cooling fan Helps keep the computer cool.
Note: Do not cover or obstruct the opening of the fan.
6 Memory comparment House the computer’s main memory.
Chapter 1 11
Indicators
The computer has three easy-to-read status icons on the upper-right above the keyboard, and four on the front
panel.
NOTE: 1. Charging: the light shows amber when the battery is charging.
NOTE: 2. Fully charged: light shows green when in AC mode.
Icon Function Description
Caps Lock Lights when Caps Lock is activated.
Num Lock Lights when Numeric Lock is activated.
Media activity Indicates when the hard disk or optical
drive is active.
Power Lights when the computer is on.
Battery Lights when the battery is being charged.
Bluetooth Indicates the status of Bluetooth
communication.
Wireless LAN Indicates the status of Bluetooth
communication.
Icon Function Description
12 TravelMate 4060
Easy-Launch Buttons
Located at the upper-right, above the keyboard are four buttons. These buttons are called launch keys. They
are mail, Web browser, Acer Empowering key “ “, and one user-programmable button.
Press “ “ to run the Acer eManager. The mail and Web buttons are pre-set ot email and internet programs,
but can be reset by users. To set the Web browser, mail and programmable keys, run the Acer Launch
Manager.
Launch key Default application
P User-programmable
Acer eManager (user-programmable)
Web browser Internet browser (user-programmable)
Mail Email application (user-programmable)
Chapter 1 13
Using the keyboard
The keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and
twelve function keys.
Lock keys and embedded numeric keypad
The keyboard has three lock keys which you can toggle on and off.
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Windows keys
The keyboard has two keys that perform Windows-specific functions.
Lock key Description
Caps Lock
@
When @is on, all alphabetic characters typed are in uppercase.
Num Lock <Fn>+<F11>
]
When ] is on, the embedded keypad is in numeric mode. The keys function
as a calculator (complete with the arithmetic operators ), -, *, and /). Use this mode
when you need to do a lot of numeric data entry. A better solution would be to
connect an external keypad.
Scroll Lock <Fn>+<F12>
[
When [ is on, the screen moves one line up or down when you press the up
or down arrow keys respectively. [ does not work with some applications.
Desired access Num lock on Num lock off
Number keys on embedded
keypad
Type numbers in a normal manner.
Cursor-control keys on embedded
keypad
Hold <Shift> while using cursor-control
keys.
Hold <Fn> while using cursor-
control keys.
Main keyboard keys Hold <Fn> while typing letters on embedded
keypad.
Type the letters in a normal manner.
14 TravelMate 4060
Hot Keys
The computer employs hot keys or key combinations to access most of the computer’s controls like screen
contrast and brightness, volume output and the BIOS Utility.
To activate hot keys, press and hold the <Fn> key before pressing the other key in the hot key combination.
Keys Description
Windows logo key
Start button. Combinations with this key perform shortcut functions. Below
are a few examples:
+ <Tab> (Activates the next Taskbar button)
+ <E> (Opens the My Computer window)
+ <F1> (Opens Help and Support)
+ <F> (Opens the Find: All Files dialog box)
+ <R> (Opens the Run dialog box)
+ <M> (Minimizes all windows)
<shift>+ +< M> (Undoes the minimize all windows)
Application key This key has the same effect as clicking the right mouse button; it opens the
application’s context menu.
Hot Key Icon Function Description
Fn-lHotkey help Displays a list of the hotkeys and their functions.
Fn-mAcer eSetting Launches Acer eSetting in the eManager set by the
Acer Empowering key..
Chapter 1 15
Special keys
You can locate the Euro symbol at the upper-center (for European keyboard) and/or bottom-right (Chinese
keyboard) of your keyboard. To type:
Fn-nPower Management Launches Power options.
Fn-oSleep Puts the computer in Sleep mode.
Fn-pDisplay toggle Switches display output between the display screen,
external monitor (if connected) and both the display
screen and external monitor.
Fn-qScreen blank Turns the display screen backlight off to save power.
Press any key to return.
Fn-rTouchpad Toggle Turns the internal touchpad on and off.
Fn-sSpeaker toggle Turns the speakers on and off.
Fn-wVolume up Increases the sound volume.
Fn-yVolume down Decreases the sound volume.
Fn-xBrightness up Increases the screen brightness.
Fn-¨zBrightness down Decreases the screen brightness.
Hot Key Icon Function Description
16 TravelMate 4060
The Euro symbol
1. Open a text editor or word processor.
2. Either directly press the <Euro> key at the bottom-right of the keyboard (for Chinese keyboard), or hold
<Alt Gr> and then press the <5> key at the upper-center of the keyboard.symbol at the upper-center of
the keyboard (for European keyboard, you can use both method).
NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm for more information.
The US dollar sign
1. Open a text editor or word processor.
2. Either directly press the <Euro> key at the bottom-right of the keyboard (for Chinese keyboard), or hold
<Shift> and then press the <4> key at the upper-center of the keyboard.symbol at the upper-center of the
keyboard (for European keyboard, you can use both method).
NOTE: This function varies according to the language settings.
Chapter 1 17
Touchpad
The built-in touchpad is a pointing device that senses movement on its surface. This means the cursor
responds as you move your finger on the surface of the touchpad. The central location on the palmrest
provides optimum comfort and suuport.
Touchpad basics
The following items teach you how to use the touchpad:
* Move your finger across the touchpad (2) to move the cursor.
* Press the left (1) and right (4) buttons located on the edge of the touchpad to do selection and execution
functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the touchapd is
the same as clicking the left button.
* Use the 4-way scroll (3) button to scroll up or down and move left or right a page. This button mimics your
cursor pressing on the right scroll bar of Windows applications.
NOTE: Keep your fingers dry and clean when using the touchpad. Also keep the touchpad dry and clean. The
touchpad is sensitive to finger movement, hence, the lighter the touch, the better the response. Taping
harder will not increase the touchpad’s responsiveness.
Function Left button (1) Right button (4) Touchpad (2) Center button (3)
Execute Click twice quickly. Tap twice (at the same speed
as double-clicking a mouse
button).
Select Click once. Tap once.
Drag Click and hold,
then use finger to
drag the cursor on
the touchpad.
Tap twice (at the same speed
as double-clicking a mouse
button); hold finger to the
touchpad on the second tap
and drag the cursor.
Access
context menu
Click once.
Scroll Click and hold to
move up/down/left/
right.
18 TravelMate 4060
Hardware Specifications and Configurations
System Board Major Chip
Item Controller
System core logic Intel® 915GM+ICH6-M
Memory controller Integrated in Intel® 915GM
Audio controller RealTek ALC260 HD audio interface
(Audio amplifer: Maxiam MAX9755)
PCMCIA controller for socket TI PCI1510A
Video controller built-in Intel® 915GM
Power and Keyboard controller KBC NS97551
Wireless controller (mini PCI) Intel (The controller is on the Wireless LAN card. Please look at the
wireless LAN card for controller details).
Processor
Item Specification
CPU type Intel® Pentium® M 730/740/750/760/770/780 processor (2MB L2 cache,
1.60/1.73/1.86/2/2.13/2.26 GHz, 533 MHz FSB)
Intel® Pentium® M 725 processor (2MB L2 Cache, 1.60 GHz, 400 MHz FSB)
Intel® Celeron® M processor 360/370/380 (1 MB L2 cache, 1.40/1.50/1.60
GHz, 400 MHz FSB)
CPU package Intel socketable 478 pins Micro-FCPGA
CPU core voltage Low speed: 0.8V
High speed: 1.5V
CPU I/O voltage 1.2V
BIOS
Item Specification
BIOS vendor Pheonix BIOS
BIOS Version
BIOS ROM type Flash ROM, SST39VF040
BIOS ROM size 512Kbyte
BIOS package 32 Pin PLCC-lead
Supported protocols ACPI 2.0 (if available, at least 1.0b), SMBIOS 2.3, PCI 2.2, Boot Block,
PXE 2.0, Mobile PC2001, Hard Disk Password, INT 13h Extensions, PCI
Bus Power Management interface Specification, EI Torito-Bootable CD-
ROM Format Specification V1.0, Simple Boot Flag 1.0
Second Level Cache
Item Specification
Cache controller Built-in CPU
Cache size 2MB for Intel® Pentium® M processor
1MB for Intel® Celeron® M processor
1st level cache control Always Enabled
2nd level cache control Always Enabled
Chapter 1 19
Above table lists some system memory configurations. You may combine DIMMs with various capacities to
form other combinations.
Cache scheme control Fixed-in write back
System Memory
Item Specification
Memory controller built-in CPU
Onboard memory size 0MB
DIMM socket number 2 Sockets
Supports memory size per socket 256MB(min)/1024MB(max)
Supports maximum memory size 2GB with 2 SODIMM support
Supports DIMM type DDRII
Supports DIMM Speed 533MHz
Supports DIMM voltage 1.8 V/0.9V
Supports DIMM package 200-pin so-DIMM
Memory module combinations You can install memory modules in any combinations as long as they
match the above specifications .
Memory Combinations
Slot 1 Slot 2 Total Memory
0MB 256MB 256MB
0MB 512MB 512MB
0MB 1024MB 1024MB
256MB 0MB 256MB
256MB 256MB 512MB
256MB 512MB 768MB
256MB 1024MB 1280MB
512MB 0MB 512MB
512MB 256MB 768MB
512MB 512MB 1024MB
512MB 1024MB 1536MB
1024MB 0MB 1024MB
1024MB 256MB 1280MB
1024MB 512MB 1536MB
1024MB 1024MB 2048MB (2G)
LAN Interface
Item Specification
Chipset RealTek 8100CL
Supports LAN protocol 10/100
LAN connector type RJ45
LAN connector location Right side
Second Level Cache
Item Specification
20 TravelMate 4060
.
Modem Interface
Item Specification
Chipset CS1037 Internal Agere Scorpio chipset (Scorpio+CSP1037B)
Fax modem data baud rate (bps) 14.4K
Data modem data baud rate (bps) 56K
Supports modem protocol V.92MDC
Modem connector type RJ11
Modem connector location Right side
Wireless Module 802.11b/g (optional device)
Item Specification
Chipset
Data throughput 11M~54M bps
Protocol 802.11 b+g
Interface Mini-PCI type II
Floppy Disk Drive Interface
Item Specification
Vendor & model name There is no FDD module for this product
Floppy Disk Specifications
Media recognition 2DD (720KB) 2HD (1.2 MB, 3 mode) 2HD (1.44MB)
Sectors/track 9 15 18
Tracks 80 80 80
Data transfer rate
(Kbit/s)
1 MB 1.6 MB 2 MB
Rotational speed (RPM) 300 360 300
Read/write heads 2
Encoding method MFM
Power Requirement
Input Voltage (V) +5V
Hard Disk Drive Interface
Item
Vendor & Model
Name
HGST MORAGA
IC25N060ATMR04-0
08K0634
Seagate N2 ST960821A
TOSHIBA PLUTO
MK6025GAS
HGST MORAGA
IC25N080ATMR04-0 08K635
Seagate N2 ST9808210A
TOSHIBA PLUTO
MK6025GAS
TOSHIBA PLUTO
MK1031GAS
SEAGATE N2 ST9100822A
Capacity (MB) 60000 80000 100000
Bytes per sector 512 512 512
Logical heads 16 16 16
Logical sectors 63 63 63
Drive Format
Logical cylinders 16383 16383 16383
Chapter 1 21
Physical read/write
heads
3/3/4 4/3/2 4
Disks 2/2/4 2/2/4 2
Spindle speed (RPM) 4200RPM 4200RPM 4200RPM
Performance Specifications
Buffer size 8MBytes (8192kbytes) 8MBytes (8192kbytes) 8MBytes
Interface ATA-6 ATA/ATAPI-6 ATA/ATAPI-6
Data transfer, rate
(host~buffer, Mbytes/
s)
100 MB/Sec 100 MB/Sec 100 MB/Sec
DC Power Requirements
Voltage tolerance 5 +/- 5% 5 +/- 5% 5 +/- 5%
Combo Drive Interface
Item Specification Remark
Vendor & model name DVD/CDRW TOSHIBA TS-L462A
General Specification
Interface Enhanced IDE (ATAPI)
Disc Diameter 8cm/12cm
Loading Type Drawer Type
Drive Mounting Horizontal/Vertical
Read/Write Read Speed:
Max. 24X(3,600 KB/sec) for CD-ROM
Max. 24X(3,600 KB/sec) for CD-RW
Write Speed:
Max. 24X(3,600 KB/sec) for CD-R
Max. 10X(1,500 KB/sec) for CD-RW
Max. 24X(3,600 KB/sec) for US-RW
CAV 24X
CAV 24X
P-CAV 24X/20X/16X ; CLV 10X/8X/4X
CLV 10X/4X
P-CAV 24X/16X
Mounting Orientation Horizontal/Vertical All angles
Buffer Under Run 2MB
Power consumption DC +5v/1.2A
Interface Enhanced IDE(ATAPI) compatible
Media compatibility CD:
120mm CD-ROM (Read Only)
80mm CD
800/700/650/550MB CD-Recordable (Read & Write)
700/650MB CD-Rewritable (Read & Write)
700/650MB High Speed CD-Rewritable (Read & Write)
DVD:
5/9/10/18 DVD-Single/Dual (PTP, OTP)
3.9/4.7G DVD-R (Read Only)
4.7GDVD+R (Read Only)
DVD±RW (Read only)
80mm DVD
Hard Disk Drive Interface
Item
22 TravelMate 4060
Format compatibility CD
CD-DA (Red Book) - Standard Audio CD & CD-TEXT
CD-ROM (Yellow Book Mode1 & 2) - Standard Data
CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session
CD-I /FMV (Green Book, Mode2 Form1 & 2, Ready, Bridge)
CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video
Video-CD (White Book) - MPEG1 Video
DVD
DVD-ROM (Book 1.02),
DVD-Video (Book 1.1)
DVD-R (Book 1.0, 3.9G)
DVD-R (Book 2.0, 4.7G) - General & Authoring
DVD+R (Version 1.0)
DVD±RW
Play DVD-AUDIO except the case that required CPPM
(Content protection for prerecorded Media)
Write Method
Loading mechanism Load: Manual
Release: (a) Electrical Release
(Release Button)
(b) Release by ATAPI
command
(c) Emergency Release
Power Requirement
Input Voltage DC +5V+/- 5% (operation)
DC +5V+/- 8% (start up)
DVD-RW Interface
Item Specification
Vendor & model name TOSHIBA TS-L532A
Performance Specification
Transfer rate (KB/sec)
(1) Read DVD-ROM
DVD-R
CD-ROM
(2) Write CD-R
CD-RW
HS-RW
US-RW
(3) ATAPI Interface
PIO mode
DMA mode
Ultra DMA mode
MAX 8X CAV (MAX 10800kB/s)
MAX 4X CAV (MAX 5400kB/s)
MAX 24X CAV (MAX 3600kB/s)
4X, 8X (CLV), MAX. 24X(ZCLV)
4X (CLV)
4X, 8X, 10X (CLV)
8X, 10X(CLV), MAX. 16X (ZCLV)
16.6MB/s: PIO mode4
16.6MB/s: Multi word mode2
33.3MB/s: Ultra DMA mode2
Buffer Memory 2MB
Interface Enhanced IDE(ATAPI) compatible
Applicable disc format Read:
copy-protected DVD discs, CD-ROM, CD audio, DVD-ROM and DVD-RAM,
DVD-R/-RW, DVD+R/+RW and CD-R/-RW, DVD-ROM, DVD-R/+R, DVD-R/+R,
DVD-RW/+RW, 4.38GB DVD-RAM, CD-DA discs, CD-ROM discs, CD-R discs,
CD-RW discs
Write:
CD-R, CD-RW, high-speed CD-RW, Ultra-speed CD-RW, DVD-R, DVD-RW,
DVD+R, DVD+RW
Combo Drive Interface
Item Specification Remark
Chapter 1 23
Loading mechanism Load: Manual
Release: (a) Electrical Release (Release Button)
(b) Release by ATAPI command
(c) Emergency Release
Power Requirement
Input Voltage 5 V +/- 5 % (Operating)
Audio Interface
Item Specification
Audio Controller Realtek ALC260 (Audio amplifier: Maxim MAX9755)
Audio onboard or optional Built-in
Mono or Stereo Stereo
Resolution 18 bit stereo full duplex
Compatibility HD audio Interface; S/PDIF output for PCM or AC-3 content
Sampling rate 1Hz resolution VSR (Variable Sampling Rate)
Internal microphone Yes
Internal speaker / Quantity Yes
Supports PnP DMA channel DMA channel 0
DMA channel 1
Supports PnP IRQ IRQ10, IRQ11
Video Interface
Item Specification
Vendor & Model Name built-in Intel® 915GM
Video memory size up to 128MB for Aspire 3000/5000
up to 64MB for Aspire 3500
Chip voltage Core / 2.5V, 1.5V,
Supports ZV (Zoomed Video) port NO
Graph interface 4X AGP (Accelerated Graphic Port) Bus
Maximum resolution LCD 1600X1200 (UXGA)
Maximum resolution CRT 2048X1536@60HZ
Video Resolutions Mode
Monitor Resolution Hz
2D Display Mode
640x480 120
800x600 120
1024x768 120
1152X864 120
1280X1024 120
1600x1200 85
1920x1080*16:9 75
1920x1200 75
1920x1440 75
DVD-RW Interface
Item Specification
24 TravelMate 4060
Resolution, colors and maximum refersh rate (Hz) in 256, 65K or 16.7M colors.
NOTE: 16:9 aspect ratio monitors are supported on 1920x1080 and 848x480 on Windows(R)XP, Windows(R)
2000 and Windows(R)ME. The complete list of resolutions depends on the driver version and operating
system. NOTE: resolutions are limited by the performance of the attached monitor.
2048x1536 60
USB Port
Item Specification
USB Compliancy Level 2.0
OHCI USB 2.0
Number of USB port 3
Location Two on the right side; one on the front side
Serial port function control Enable/Disable by BIOS Setup
PCMCIA Port
Item Specification
PCMCIA controller TI PCI1510A
Supports card type Type II (No Tpye III)
Number of slots One type II
Access location Right side
Supports ZV (Zoomed Video) port NO
Supports 32 bit CardBus Yes (IRQ17)
Keyboard
Item Specification
Keyboard controller KBC NS97551
Keyboard vendor Darfon
Total number of keypads 88-/89-key
Windows keys Yes
Internal & external keyboard work simultaneously Yes
Battery
Item Specification
Vendor & model name SANYO
PANASONIC
PANASONIC (RoHS)
SANYO LI-ION 4UR18650F-2-QC141
SIMPPLO
SONY
Battery Type Lithium-ION
Pack capacity 4400mAH
Nominal voltage 14.8V
Number of battery cell 8
Video Resolutions Mode
Monitor Resolution Hz
Chapter 1 25
Package configuration 4S2P for Sanyo and Panasonic
4S1P for Sanyo QC141,SIMPPLO and SONY
Package voltage 41.8V / 9.6V
LCD
Item Specification
Vendor & model name AU B154EW01-08 QDI QD15TL02-03
Screen Diagonal (mm) 15.4inch 15.4inch
Active Area (mm) 331.2(H)x207.0(V) 331.2(H)x207.0(V)
Display resolution (pixels) WXGA (1280x800) WXGA (1280x800)
Pixel Pitch 0.2588(H)x0.2588(H)mm 0.2588(H)x0.2588(H)mm
Pixel Arrangement RGB vertical stripe RGB vertical stripe
Display Mode Normally white Normally white
Surface Treatment Not show glossy, hardness 2H
Typical White Luminance (cd/m2)
also called Brightness
180 160
Luminance Uniformity not show 1.4(max)
Contrast Ratio 400 400
Response Time (Optical Rise Time/Fall
Time)msec
16 25(5ms for rise+20 ms for
decay)
Nominal Input Voltage VDD not show not show
Typical Power Consumption (watt) 6.5 (max) 4.38 (for lamp)
Weight 585 585
Physical Size(mm) 344(W)x222(H)x6.5(D) 344(W)x222(H)x6.5(D)
Support Color Native 262K colours 262K colours
Viewing Angle (degree)
Horizontal: Right/Left
Vertial: Upper/Lower
40/40
10/30
45/45
15/35
Temperature Range( C)
Operating
Storage (shipping)
0 to 50
-20 to 60
0 to 50
-20 to 60
AC Adapter
Item Specification
Vendor & model name LITE-ON PA-1650-02QR
LI SHIN SLS0335A19A57LF
DELTA SADP-65KB
Input Requirements
Maximum input AC current 3.42A
Inrush currenct 50A @ 115Vac
100A @ 230Vac
Nominal frequency (Hz) 50-60
Frequency variation range (Hz) 47-63
Input voltage range (Vrms) 90V AC-264V AC
Inrush current The maximum inrush current will be less than 50A and 100A when the adapter
is connected to 115Vac and 230Vac respectively.
Battery
Item Specification
°
26 TravelMate 4060
Efficiency It should provide an efficiency of 83% minimum, when measured at maximum
load under 115Vac.
Output Ratings (CV mode)
DC output voltage 19V
Noise + Ripple 300mVp-pmax (20 MHz bandwidth)
Load 0(min) 3.16A(max)
Output Ratings (CC mode)
DC output voltage 19V +/-1.0V for CV mode
Constant current mode 3.6 +/- 0.3A
Dynamic Output Characteristics
Turn-on delay time 3 sec (@ 115Vac)
Hold up time 5ms (@115Vac, Full load)
Over Voltage Protection (OVP) 24V
Short circuit protection 3.9A max can be protected and output can be shorted without damage
Electrostatic discharge (ESD) 15KV (at air discharge)
8KV (at contact discharge)
Dielectric Withstand Voltage
Primary to secondary 3000Vac
Leakage current 0.25 mA max. (@ 254Vac, 60Hz)
Regulatory Requirements Safety Requirements:
1.The subject product rated 100-120V 60Hz must be listed under UL 1950 and
certified with SCA Standard C22.2 No.950.
2.The subject product rated 200-240V 50Hz must comply with low voltage
directive 73/23EEC.
EMI Requirements:
1.The subject product rated 100-120V 60Hz must meet the EMI requirements
of FCC part 15, Subpart B for Class B Digital Device and get FCC Certification
before marketing into USA and Canada.
2.The subject product rated 200-240V 50Hz must meet the EMC Directive 89/
336/EEC.
3.The subject product rated 100-120V must meet the VCCI-2 EMI
requirements.
Power Management
ACPI Mode Power Management
Mech. Off (G3) All devices in the system are turned off completely.
Soft Off (G2/S5) OS initiated shutdown. All devices int he sytem are turned off
completely.
Working (G0/S0) Individual devices such as the CPU and hard disk may be power
managed in this state.
S3 Sleeping State CPU set power down
VGA suspend
PCMCIA suspend
Audio Power Down
Hard Disk Power Down
CD-ROM Power Down
Super I/O Low Power mode
S4 Sleeping State Also called Hibernate stats. System saves all system state and
data onto disk prior to power off the whole system.
AC Adapter
Item Specification
Chapter 1 27
Environmental Requirements
Item Specification
Temperature
Operating +0~+35 °C
Non-operating -20~+65 °C
Package storage -20~+65 °C
Humidity
Operating 10% to 90% RH, non-condensing
Non-operating 10% to 90% RH, non-condensing (Unpacked)
Non-operating 10% to 90% RH, non-condensing (Storage package)
Vibration
Operating (unpacked) Operation vibration: 1.0G ,X,Y,Zaxis, 30 minutes/axis
Non-operating (unpacked) 5~27.1Hz: 0.6G
27.1~50Hz: 0.04mm (peak to peak)
50~500Hz: 2.0G
Non-operating (packed) 5~62.6Hz: 0.51mm (peak to peak)
62.6~500Hz: 4.0G
Mechanical Specification
Item Specification
Dimensions 364(W) x 279(D) x 33.9/38.9 (H)mm
14.3 3X 10.98x 1.33/1.53 inches
Weight 6.4 Ibs (2.91kg) for 15” XGA LCD model
6.5 lbs (2.94kg) for 15.4” WXGA LCD model
I/O Ports Three USB 2.0 ports
Ethernet (RJ-45) port
Modem (RJ-11) port
External display (VGA) port
Microphone-in jack
Line-in jack
Headphones/speaker/line-out jack
Type II PC Card slot
DC-in jack for AC adaptor
Drive Bays One
Indicators LED indicator for keyboard hot key: Caps Lock, Scroll Lock, NUmber lock
LED indicator for function indicator: System power-on, HDD/ODD, Wireless on/off,
Arcade LED mode, DC-in, Battery/Charging indicator
Switch Power
Chapter 2 28
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
Press m to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
PhoenixBIOS Setup Utility
CPU Type :
Intel (R) Pentium (R) processor 1.73GHz
CPU Speed :
System BIOS Version :
2A02
VGA BIOS Version :
Alviso 1219
KBC Version :
1A16
Serial Number : LXT123456705290116EF00
Asset Tag Number :
N/A
Produce Name
Aspire 1640
Manufacturer Name:
Acer
UUID :
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
F1 Help
↑↓
Select Item F5/F6 Change Values F9 Setup Defaults
Esc Exit
←
→
Select Menu Enter Select
4
Sub-Menu F10 Save and Exit
HDD Model Name:
HDD Serial Number :
TOSHIBA MK1031GAS
751U0320S
1733MHz
ATAPI Device : HL-DT-ST DVD-RW GWA-4082N
Main Security Boot Exit
Info.
System Utilities
Chapter 2
29 Chapter 2
Navigating the BIOS Utility
There are six menu options: Info., Main, System Devices, Security, Boot, and Exit.
Follow these instructions:
TTo choose a menu, use the cursor left/right keys (zx).
TTo choose a parameter, use the cursor up/down keys ( wy).
TTo change the value of a parameter, press por q.
TA plus sign (+) indicates the item has sub-items. Press e to expand this item.
TPress ^ while you are in any of the menu options to go to the Exit menu.
TIn any menu, you can load default settings by pressing t. You can also press u to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values. Please
note that system information vary in models.
Chapter 2 30
Information
NOTE: The system information is subject to different models.
Parameter Description
HDD Model Name This field shows the model name of HDD installed on primary IDE master.
HDD Serial Number This field displays the serial number of HDD installed on primary IDE master.
ATAPI Device This field displays the mofel name of devices installed on secondary IDE master. The hard
disk drive or optical drive model name is automatically detected by the system.
System BIOS Version This field displays the BIOS version of the system.
VGA BIOS Version This field displays the VGA BIOS version of this system.
KBC Version This filed displays the KBC version of this system.
ATAPI Serial Number This field shows the serial number of devices installed on secondary IDE master.
Serial Number This field displays the serial number of this unit.
Asset Tag Number An Asset Tag with 32 bytes will be stored in EEPROM. Default value is set as
“0000000000000000” (in binary code).
PhoenixBIOS Setup Utility
CPU Type :
Intel (R) Pentium (R) processor 1.73GHz
CPU Speed :
System BIOS Version :
2A02
VGA BIOS Version :
Alviso 1219
KBC Version :
1A16
Serial Number : LXT123456705290116EF00
Asset Tag Number :
N/A
Produce Name
Aspire 1640
Manufacturer Name:
Acer
UUID :
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
F1 Help
↑↓
Select Item F5/F6 Change Values F9 Setup Defaults
Esc Exit
←
→
Select Menu Enter Select
4
Sub-Menu F10 Save and Exit
HDD Model Name:
HDD Serial Number :
TOSHIBA MK1031GAS
751U0320S
1733MHz
ATAPI Device : HL-DT-ST DVD-RW GWA-4082N
Main Security Boot Exit
Info.
31 Chapter 2
UUID Number This will be visible only when there is an internal LAN device present. UUID means
Universally Unique ID, a method for computing object identifiers (OIDs). It uses the serial
number in the local Ethernet card combined with the date and time to generate a 128 bit
(16bytes) number. For Acer product, this field displays UUID number. A UUID string will be
stored in the secured data area which is an alphanumeric string of maxium 16 bytes in
length.
Parameter Description
Chapter 2 32
Main
The Main screen displays a summary of your computer hardware information, and also includes basic setup
parameters. It allows the user to specify standard IBM PC AT system parameters.
NOTE: The screen above is for reference only. Actual values may differ.
PhoenixBIOS Setup Utility
Information
Main Security Boot Exit
Item Specific Help
System Time: [05:45:48]
System Date: [08/30/2005]
System Memory: 640 KB
Extended Memory: 1040 MB
Video Memory [128MB]
Quiet Boot: [Enabled]
Power On Display: [Both]
Network Boot [Enabled]
F12 Boot Menu
[Disabled]
<Tab>, <Shift-Tab>, or
<Enter> selects field.
F1 Help
↑↓
Select Item F5/F6 Change Values F9 Setup Defaults
Esc Exit
←
→
Select Menu Enter Select
4
Sub-Menu F10 Save and Exit
Shows system base memory size
Shows extended memory size
VGA memory size
D2D Recovery [Enabled]
33 Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is
because the user is not allowed to control the settings in these cases.
Parameter Description Format/Option
System Time Sets the system time. The hours are displayed
with 24-hour format.
Format: HH:MM:SS
(hour:minute:second) System Time
System Date Sets the system date. Format MM/DD/YYYY (month/day/
year)
System Date
System Memory This field reports the memory size of the system.
Memory size is fixed to 640MB
Extended Memory This field reports the memory size of the
extended memory in the system.
Extended Memory size=Total memory size-1MB
VGA Memory Shows the VGA memory size. VGA Memory
size=64/128MB
Quiet Boot Determines if Customer Logo will be displayed or
not; shows Summary Screen is disabled or
enabled.
Enabled: Customer Logo is displayed, and
Summary Screen is disabled.
Disabled: Customer Logo is not displayed, and
Summary Screen is enabled.
Option: Enabled or Disabled
Power on display Auto: During power process, the system will
detect if any display device is connected on
external video port. If any external display device
is connected, the power on display will be in CRT
(or projector) only mode. Otherwise it will be in
LCD only mode.
Both: Simultaneously enable both the integrated
LCD screen and the system’s external video port
(for an external CRT or projector).
Option: Both or Auto
Network Boot Enables, disables the system boot from LAN
(remote server).
Option: Enabled or Disabled
F12 Boot Menu Enables, disables Boot Menu during POST. Option: Disabled or Enabled
D2D Recovery Enables, disables D2D Recovery function. The
function allows the user to create a hidden
partition on hard disc drive to store operation
system and restore the system to factory
defaults.
Option: Enabled or Disabled
Chapter 2 34
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.
PhoenixBIOS Setup Utility
Information Main Boot
Item Specific Help
Supervisor Password Is :
User Password Is : Clear
Set Supervisor Password
Set User Password
Set HDD Password
Password on Boot [Disabled]
Supervisor Password
controls accesses of the
whole setup utility.
It can be used to
boot up when Password
on boot is enabled.
F1 Help
↑↓
Select Item F5/F6 Change Values F9 Setup Defaults
Esc Exit
←
→
Select Menu Enter Select
4
Sub-Menu F10 Save and Exit
[Enter]
[Enter]
[Enter]
Exit
Security
HDD Password Is : Clear
HDD Master ID : 15422442
Clear
35 Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
NOTE: The User Password can chagne the following items in BIOS: System Date, System Time and Power
on Display on Main menu, System Devices menu and Set User Password function on Security menu.
Meanwhile, the Supervisor Password can change ALL settings in BIOS.
Setting a Password
Follow these steps as you set the user or the supervisor password:
1. Use the w andy keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Supervisor Password box appears:
Parameter Description Option
User Password Is Shows the setting of the user password. Clear or Set
Supervisor Password Is Shows the setting of the Supervisor password.
Please note that Supervisor Password controls
access to the entire Setup. The Supervisor
Password can be used to boot up when
Password on boot is set to enabled.
Clear or Set
HDD Password Is Shows the setting of the HDD password. Clear or Set
Set User Password Press Enter to set the user password. When
user password is set, this password protects
the BIOS Setup Utility from unauthorized
access. The user can enter Setup menu only
and does not have right to change the value of
parameters.
Set Supervisor Password Press Enter to set the supervisor password.
When set, this password protects the BIOS
Setup Utility from unauthorized access. The
user can not either enter the Setup menu nor
change the value of parameters.
Set HDD Password Press Enter to set the HDD password.
Primary Harddisk Security This feature is available to user when
Supervisor password is set. Password can be
written on HDD only when Supervisor
password or user password is set and
password on HDD is set to enabled.
Supervisor Password is written to HDD only
when Supervisor password is being set. User
password is written to HDD when both
passwords are set. When both Supervisor and
user password are present, both passwords
can unlock the HDD.
Disabled or Enabled
Password on Boot Defines whether a password is required or not
while the events defined in this group
happened. The following sub-options are all
requires the Supervisor password for changes
and should be grayed out if the user password
was used to enter setup.
Disabled or Enabled
Chapter 2 36
2. Type a password in the “Enter New Password” field. The password length can not exceeds 8
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3. Press e.
After setting the password, the computer sets the User Password parameter to “Set”.
4. If desired, you can opt to enable the Password on boot parameter.
5. When you are done, press u to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
1. Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Password box appears:
2. Type the current password in the Enter Current Password field and press e.
3. Press e twice without typing anything in the Enter New Password and Confirm New Password fields.
The computer then sets the Supervisor Password parameter to “Clear”.
4. When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Changing a Password
1. Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Password box appears:
2. Type the current password in the Enter Current Password field and press e.
37 Chapter 2
3. Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4. Press e. After setting the password, the computer sets the User Password parameter to “Set”.
5. If desired, you can enable the Password on boot parameter.
6. When you are done, press u to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
The password setting is complete after the user presses u.
If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following
message.
Chapter 2 38
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
PhoenixBIOS Setup Utility
Info. Main Advanced Security Exit
Item Specific Help
Floppy Devices
+Hard Drive
+ and - indicate device
categories. Use <Enter> to
expand/collapses.
Boot order is top-down using
only the top device in each
category.
Use <F6> and <F5> to move
highlighted item up and down.
F1 Help
↑↓
Select Item F5/F6 Change Values F9 Setup Defaults
Esc Exit
←
→
Select Menu Enter Select
4
Sub-Menu F10 Save and Exit
Network Boot
Boot
CD-ROM/DVD Drive
39 Chapter 2
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
The table below describes the parameters in this screen.
Parameter Description
Exit Saving Changes Exit System Setup and save your changes to CMOS.
Exit Discarding Changes Exit utility without saving setup data to CMOS.
Load Setup Default Load default values for all SETUP item.
Discard Changes Load previous values from CMOS for all SETUP items.
Save Changes Save Setup Data to CMOS.
PhoenixBIOS Setup Utility
Info. Main Advanced Security Boot
Item Specific Help
Exit Saving Changes
Exit Dicarding Changes
Load Setup Defaults
Exit System Setup and save
your changes to CMOS.
F1 Help
↑↓
Select Item F5/F6 Change Values F9 Setup Defaults
Esc Exit
←
→
Select Menu Enter Select
4
Sub-Menu F10 Save and Exit
Discard Changes
Exit
Save Changes
Chapter 2 40
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
TNew versions of system programs
TNew features or options
TRestore a BIOS when it becomes corrupted.
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Create Crisis Recovery Diskette
1. Rename BIOS file of this product to BIOS.wph
2. Copy BIOS.wph file to crisis folder and overwrite the original BIOS.wph file.
3. Insert a blank floppy diskette to floppy drive.
4. Run cs.bat and follow its instructions to create crisis recovery diskette.
Recover BIOS from Crisis Recovery Diskette
1. Insert the crisis recovery diskette to the floppy drive.
2. Use AC adaptor power supply.
3. Press Fn and ESC key together for more than two seconds when you power on the system.
4. The system will read the files inside the floppy diskette without backlight.
5. After one to three minutes, the system will automatically reboot. Please do not shut down the system or
remove the power supply.
6. After step 1 to 5, you sould be able to recover BIOS already. Then you can see the LCD screen with the
backlight is on.
41 Chapter 2
Chapter 3 42
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
TWrist grounding strap and conductive mat for preventing electrostatic discharge
TFlat-bladed screw driver
TPhillips screw driver
TTweezers
TPlastic Flat-bladed screw driver
THexed Screw Driver
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
Chapter 3
Machine Disassembly and Replacement
43 Chapter 3
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1. Turn off the power to the system and all peripherals.
2. Unplug the AC adapter and all power and signal cables from the system
.NOTE: Aspire 9100 series product uses mylar or tape to fasten the FFC/FPC/connectors/cable, you may
need to tear the tape or mylar before you disconnect different FFC/FPC/connectors.
Chapter 3 44
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence
and instructs you on the components that need to be removed during servicing. For example, if you want to
remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in
that order.
Start
Battery
HDD Cover ODD Module
RAM/Wireless
Cover
*2
*2
HDD Module
Wireless LAN
Card Memory
IO Bezel
E*2
*2
Heatsink
Cover
special screw for thermal*3
Ex1
Thermal
Module
CPU
ODD
Connector
Board
ODD Holder
ODD Drive
*2 back side
*4 left/right side
E*3
Middle Cover
B*2
Keyboard
*4
(right and left hinges)
LCD Module
B*2
Switch Board
B*5
E*16+B*2
Lower and
Upper Case
Assembly
Upper Case
Assembly
Lower Case
Assembly
3-in-1 Cover Speaker Set Modem Board
Touchpad
Bluetooth
Module
Touchpad
Board
Touchpad
Bracket
B*2
Main Board
*4
E*2
*2 screw nuts
VGA Heatsink *3
B*2
45 Chapter 3
Screw List
Item Description
A SCREW F040 9 5.0X5.0 9.5X(IO) R00
B SCREW M2.0X0.4P+3FP ZK(NL)
C SCREW M2.5 K 5/2 X0.85 4 ZK(NL)
D SCREW M2.5X0.45+10K NIL
E SCREW M2.5X0.45+8K ZBL
F SCREW M2.5X0.45P+3F NI
G SCREW M3.0X0.8P+3K NL
4 screw pads
M*4
LCD Bezel
*6 hinges
*2 brackets
LCD Inverter
LCD
Assembly
LCD Cover
*4
LCD Module
LCD LCD Cable LCD Brackets
Antenna set
Chapter 3 46
Removing the Battery Pack
1. Unlock the battery lock.
2. Slide the battery latch as shown.
3. Then remove the battery pack.
47 Chapter 3
Removing the HDD Module/the Memory and the Wireless LAN Card/
the Thermal Module and the CPU/ODD Module and LCD Module
Removing the HDD Module
1. Remove the two screws holding the HDD cover.
2. Remove the HDD cover.
3. Remove the screw fastening the HDD module to the notebook.
4. Then detach the HDD module from the notebook.
Removing the Memory and the Wireless LAN Card
1. Remove the two screws that secure the RAM/Wireless cover.
2. Remove the RAM/Wireless cover.
3. Pop up the memory then remove it.
4. Disconnect the auxiliary and the main wireless antennae.
5. Pop the wireless LAN card then remove it.
Chapter 3 48
.
Removing the Thermal Module and CPU
1. Remove the three screws holding the thermal door
2. Detach the thermal door.
3. Disconnect the fan cable from the main board.
4. Remove the three screws fastening the thermal module.
5. Disconnect the fan cable.
NOTE: When you remove the screws fastening the thermal module, please follow the number order 3, 2, 1 on
the thermal module. When you need to assemble the thermal module, fasten the screws as the order 1,
2, 3 on the thermal module.
6. Use a flat-bladed screwdriver to release the CPU lock.
7. Remove the CPU from the socket carefully.
49 Chapter 3
Removing the ODD Module
1. Remove the three screws holding the middle cover.
2. Detach the middle cover carefully.
3. Then remove the two screws fastening the keyboard.
4. Turn over the keyboard as shown.
5. Disconnect the keyboard cable from the main board then remove the keyboard.
6. Remove the screw that fastens the ODD module.
7. Turn over the notebook computer then detach the ODD module carefully.
NOTE: When you reattach the ODD, please make sure you attach the ODD module completely to the main
unit. Otherwise, you can not fasten the screw and the screw may damage the main board.
.
Removing the LCD Module
1. Remove the three screws holding the keyboard cover.
2. Open the LCD module as the picture shown then detach the keyboard cover from the main unit.
.
Chapter 3 50
3. Remove the two screws that secure the keyboard as shown.
4. Turn over the keyboard as shown and disconnect the keyboard cable then remove the keyboard.
5. Pull out the antenna set with a tweezers then take out the antenna set from the main unit.
.
6. Disconnect the LCD coaxial cable.
7. Remove the four screws holding the right and the left hinge. Two on each side.
8. Then detach the LCD module from the main unit.
.
51 Chapter 3
Disassembling the Main Unit
Separate the Main Unit Into the Upper and the Lower Case Assembly
1. Remove the two screws holding the switch board.
2. Remove the switch board.
3. Disconnect the touchpad FFC from the main board.
4. Disconnect the bluetooth cable.
5. Remove the five screws that secure the upper case.
6. Remove the 17 screws on the bottom as shown.
7. Detach the upper case assembly and place it next to the lower case assembly.
8. Disconnect the microphone cable then remove the upper case assembly.
Disassembling the Upper Case Assembly
1. Disconnect the touchpad board to touchpad FFC.
2. Disconnect the touchpad board to main board FFC.
3. Then detach the touchpad board to main board FFC from the touchpad board.
Chapter 3 52
4. Remove the three screws that secure the touchpad board.
5. Remove the touchpad board from the upper case.
6. Disconnect the touchpad board to touchpad FFC.
7. Remove the touchpad board to touchpad FFC from the uppwer case assembly.
8. Remove the four screws holding the touchpad bracket.
9. Detach the touchpad bracket from the upper case assembly.
10. Remove the touchpad from the upper case.
11. Remove the two screws that secure the bluetooth module.
12. Disconnect the bluetooth module then remove it.
Disassembling the Lower Case Assembly
1. Disconnect the MDC cable from the modem board.
53 Chapter 3
2. Detach the MDC cable from the main board.
3. Remove the two screws holding the modem board then disconnect the modem board from the main
board.
4. Disconnect the speaker cable from the main board.
5. Remove the screw that secure the main board.
6. Remove the two screw nuts as shown.
7. The you can detach the main board from the upper case.
8. Remove the ttwo screws that fasten the N/B heatsink.
9. Remove the N/B heatsink from the main board as shown.
10. Remove the card reader dummy card from the lower case. (For SKU with three-in-one card reader, please
remove three in one cover).
11. Remove the two screws that secure the speaker set on one side.
12. Then remove another two screws holding the speaker set on the other side.
13. Then take out the speaker set from the lower case.
Chapter 3 54
IMPORTANT:When assembling/disassembling the main board, whenever there is a mylar on the main board
(see the highlighted with red below; the mylar is sami-transparent, film-like stuff ), it should be
transferred “if necessary” to the replacement main board. Because the main board mylar should be
stuck to the main board to prevent the antenna cable and the main board components short circuit.
The short could cause the main board or the antenna cable burned.
55 Chapter 3
Disassembling the LCD Module
1. Remove the four screw caps as shown.
2. Remove the four screws holding the LCD bezel.
3. Then detach the LCD bezel from the LCD module.
4. Disconnect the inverter board then remove it.
5. Remove the three screws holding the right hinge.
6. Then remove the three screws that secure the left hinge.
7. Remove one screw that secure the LCD bracket.
8. Remove another screw holding the LCD bracket on the other side.
9. Then detach the LCD panel from the LCD cover carefully.
.
10. Remove the two screws holding the right bracket.
11. Then remove the right bracket.
12. Remove another two screws that tighten the left bracket.
Chapter 3 56
13. Remove the left bracket as the picture shows.
14. Tear off the tape fastening the LCD cable.
15. Tear off the the LCD cable fastening the LCD cable, then remove it..
57 Chapter 3
Disassembling the External Modules
Disassembling the HDD Module
1. Remove the two screws holding the HDD bracket on one side.
2. Remove another two screws holding the HDD bracket on the other side.
3. Then take the hard disc drive out from the HDD bracket.
Disassembling the Optical Drive Module
1. Remove the four screws as the picture shows.
2. Remove the two screws that secure the optical disc drive and the ODD holder.
3. Push the ODD holder as shown.
4. Detach the ODD holder.
5. Disconnect the ODD connector board then remove it.
Chapter 4 58
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1. Obtain the failing symptoms in as much detail as possible.
2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.
3. Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified) Go To
Power failure. (The power indicator does not go
on or stay on.)
“Power System Check” on page 60.
POST does not complete. No beep or error
codes are indicated.
“Power-On Self-Test (POST) Error Message” on
page 63
“Undetermined Problems” on page 75
POST detects an error and displayed messages
on screen.
“Error Message List” on page 64
Other symptoms (i.e. LCD display problems or
others).
“Power-On Self-Test (POST) Error Message” on
page 63
Symptoms cannot be re-created (intermittent
problems).
Use the customer-reported symptoms and go to
“Power-On Self-Test (POST) Error Message” on
page 63
“Intermittent Problems” on page 74
“Undetermined Problems” on page 75
Troubleshooting
Chapter 4
59 Chapter 4
System Check Procedures
External Diskette Drive Check
Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is
required.
NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause
damage to the drive or cause the drive to fail.
Do the following to select the test device.
1. Boot from the diagnostics diskette and start the diagnostics program.
2. See if FDD Test is passed as the program runs to FDD Test.
3. Follow the instructions in the message window.
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1. Reconnect the external diskette drive/DVD-ROM module.
2. Replace the external diskette drive/CD-ROM module.
3. Replace the main board.
External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does
not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1. Boot from the diagnostics diskette and start the diagnostics program.
2. See if CD-ROM Test is passed when the program runs to CD-ROM Test.
3. Follow the instructions in the message window.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1. Reconnect the external diskette drive/CD-ROM module.
2. Replace the external diskette drive/CD-ROM module.
3. Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable
extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a
non-defective FRU:
1. Reconnect the keyboard cables.
2. Replace the keyboard.
3. Replace the main board.
The following auxiliary input devices are supported by this computer:
TNumeric keypad
TExternal keyboard
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
Chapter 4 60
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1. Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.
2. Go to the diagnostic memory in the test items.
3. Press F2 in the test items.
4. Follow the instructions in the message window.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1. Remove the battery pack.
2. Connect the power adapter and check that power is supplied.
3. Disconnect the power adapter and install the charged battery pack; then check that power is supplied by
the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
T“Check the Power Adapter” on page 61
T“Check the Battery Pack” on page 62
61 Chapter 4
Check the Power Adapter
Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power
adapter cable. See the following figure
1. If the voltage is not correct, replace the power adapter.
2. If the voltage is within the range, do the following:
TReplace the System board.
TIf the problem is not corrected, see “Undetermined Problems” on page 75.
TIf the voltage is not correct, go to the next step.
NOTE: An audible noise from the power adapter does not always indicate a defect.
3. If the power-on indicator does not light up, check the power cord of the power adapter for correct
continuity and installation.
4. If the operational charge does not work, see “Check the Battery Pack” on page 62.
Pin 1: +19 to +20.5V
Pin 2: 0V, Ground
Chapter 4 62
Check the Battery Pack
To check the battery pack, do the following:
From Software:
1. Check out the Power Management in control Panel
2. In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3. Repeat the steps 1 and 2, for both battery and adapter.
4. This helps you identify first the problem is on recharging or discharging.
From Hardware:
1. Power off the computer.
2. Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground).
3. If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%
of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light
up, replace the DC/DC charger board.
Touchpad Check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a
non-defective FRU:
1. Reconnect the touchpad cables.
2. Replace the touchpad.
3. Replace the system board.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement
can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware
problem. No service actions are necessary if the pointer movement stops in a short period of time.
63 Chapter 4
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes. The most likely cause is
listed first.
NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a
non-defective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 75.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified
by function.
NOTE: Most of the error messages occur during POST. Some of them display information about a hardware
device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the
way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.
Chapter 4 64
Index of Error Messages
Error Code List
Error Codes Error Messages
006 Equipment Configuration Error
Causes:
1. CPU BIOS Update Code Mismatch
2. IDE Primary Channel Master Drive Error
(THe causes will be shown before “Equipment Configuration
Error”)
010 Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh)
070 Real Time Clock Error
071 CMOS Battery Bad
072 CMOS Checksum Error
110 System disabled.
Incorrect password is specified.
<No error code> Battery critical LOW
In this situation BIOS will issue 4 short beeps then shut down
system, no message will show.
<No error code> Thermal critical High
In this situation BIOS will shut down system, not show message.
Error Message List
Error Messages FRU/Action in Sequence
Failure Fixed Disk Reconnect hard disk drive connector.
“Load Default Settings” in BIOS Setup Utility.
Hard disk drive
System board
Stuck Key see “Keyboard or Auxiliary Input Device Check” on page 59.
Keyboard error see “Keyboard or Auxiliary Input Device Check” on page 59.
Keyboard Controller Failed see “Keyboard or Auxiliary Input Device Check” on page 59.
Keyboard locked - Unlock key switch Unlock external keyboard
Monitor type does not match CMOS - Run Setup Run “Load Default Settings” in BIOS Setup Utility.
Shadow RAM Failed at offset: nnnn BIOS ROM
System board
System RAM Failed at offset: nnnn DIMM
System board
Extended RAM Failed at offset: nnnn DIMM
System board
System battery is dead - Replace and run Setup Replace RTC battery and Run BIOS Setup Utility to reconfigure
system time, then reboot system.
System CMOS checksum bad - Default
configuration used
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System timer error RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System board
65 Chapter 4
Real time clock error RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System board
Previous boot incomplete - Default configuration
used
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Memory size found by POST differed from
CMOS
Run “Load Default Settings” in BIOS Setup Utility.
DIMM
System board
Diskette drive A error Check the drive is defined with the proper diskette type in BIOS
Setup Utility
See “External Diskette Drive Check” on page 59.
Incorrect Drive A type - run SETUP Check the drive is defined with the proper diskette type in BIOS
Setup Utility
System cache error - Cache disabled System board
CPU ID: System board
DMA Test Failed DIMM
System board
Software NMI Failed DIMM
System board
Fail-Safe Timer NMI Failed DIMM
System board
Device Address Conflict Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Allocation Error for device Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Failing Bits: nnnn DIMM
BIOS ROM
System board
Fixed Disk n None
Invalid System Configuration Data BIOS ROM
System board
I/O device IRQ conflict Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Operating system not found Enter Setup and see if fixed disk and drive A: are properly identified.
Diskette drive
Hard disk drive
System board
Error Message List
Error Messages FRU/Action in Sequence
Chapter 4 66
Error Message List
No beep Error Messages FRU/Action in Sequence
No beep, power-on indicator turns off and LCD is
blank.
Power source (battery pack and power adapter). See “Power
System Check” on page 60.
Ensure every connector is connected tightly and correctly.
Reconnect the DIMM.
LED board.
System board.
No beep, power-on indicator turns on and LCD is
blank.
Power source (battery pack and power adapter). See “Power
System Check” on page 60.
Reconnect the LCD connector
Hard disk drive
LCD inverter ID
LCD cable
LCD Inverter
LCD
System board
No beep, power-on indicator turns on and LCD is
blank. But you can see POST on an external
CRT.
Reconnect the LCD connectors.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
No beep, power-on indicator turns on and a
blinking cursor shown on LCD during POST.
Ensure every connector is connected tightly and correctly.
System board
No beep during POST but system runs correctly. Speaker
System board
67 Chapter 4
Phoenix BIOS Beep Codes
Code Beeps POST Routine Description
02h Verify Real Mode
03h Disable Non-Maskable Interrupt (NMI)
04h Get CPU type
06h Initialize system hardware
08h Initialize chipset with initial POST values
09h Set IN POST flag
0Ah Initialize CPU registers
0Bh Enable CPU cache
0Ch Initialize caches to initial POST values
0Eh Initialize I/O component
0Fh Initialize the local bus IDE
10h Initialize Power Management
11h Load alternate registers with initial POST
values
12h Restore CPU control word during warm boot
13h Initialize PCI Bus Mastering devices
14h Initialize keyboard controller
16h 1-2-2-3 BIOS ROM checksum
17h Initialize cache before memory autosize
18h 8254 timer initialization
1Ah 8237 DMA controller initialization
1Ch Reset Programmable Interrupt Controller
20h 1-3-1-1 Test DRAM refresh
22h 1-3-1-3 Test 8742 Keyboard Controller
24h Set ES segment register to 4 GB
26h Enable A20 line
28h Autosize DRAM
29h Initialize POST Memory Manager
2Ah Clear 215 KB base RAM
2Ch 1-3-4-1 RAM failure on address line xxxx
2Eh 1-3-4-3 RAM failure on data bits xxxx of low byte of
memory bus
2Fh Enable cache before system BIOS shadow
30h 1-4-1-1 RAM failure on data bits xxxx of high byte of
memory bus
32h Test CPU bus-clock frequency
33h Initialize Phoenix Dispatch Manager
36h Warm start shut down
38h Shadow system BIOS ROM
3Ah Autosize cache
3Ch Advanced configuration of chipset registers
3Dh Load alternate registers with CMOS values
42h Initialize interrupt vectors
45h POST device initialization
46h 2-1-2-3 Check ROM copyright notice
Chapter 4 68
48h Check video configuration against CMOS
49h Initialize PCI bus and devices
4Ah Initialize all video adapters in system
4Bh QuietBoot start (optional)
4Ch Shadow video BIOS ROM
4Eh Display BIOS copyright notice
50h Display CPU type and speed
51h Initialize EISA board
52h Test keyboard
54h Set key click if enabled
58h 2-2-3-1 Test for unexpected interrupts
59h Initialize POST display service
5Ah Display prompt “Press F2 to enter SETUP”
5Bh Disable CPU cache
5Ch Test RAM between 512 and 640 KB
60h Test extended memory
62h Test extended memory address lines
64h Jump to User Patch1
66h Configure advanced cache registers
67h Initialize Multi Processor APIC
68h Enable external and CPU caches
69h Setup System Management Mode (SMM) area
6Ah Display external L2 cache size
6Bh Load custom defaults (optional)
6Ch Display shadow-area message
6Eh Display possible high address for UMB
recovery
70h Display error messages
72h Check for configuration errors
76h Check for keyboard errors
7Ch Set up hardware interrupt vectors
7Eh Initialize coprocessor if present
80h Disable onboard Super I/O ports and IRQs
81h Late POST device initialization
82h Detect and install external RS232 ports
83h Configure non-MCD IDE controllers
84h Detect and install external parallel ports
85h Initialize PC-compatible PnP ISA devices
86h Re-initialize onboard I/O ports
87h Configure Motherboard Configurable Devices
(optional)
88h Initialize BIOS Area
89h Enable Non-Maskable Interrupts (NMIs)
8Ah Initialize Extended BIOS Data Area
8Bh Test and initialize PS/2 mouse
8Ch Initialize floppy controller
Code Beeps POST Routine Description
69 Chapter 4
8Fh Determine number of ATA drives (optional)
90h Initialize hard-disk controllers
91h Initialize local-bus hard-disk controllers
92h Jump to UserPatch2
93h Build MPTABLE for multi-processor boards
95h Install CD ROM for boot
96h Clear huge ES segment register
97h Fixup Multi Processor table
98h 1-2 Search for option ROMs. One long, two short
beeps on checksum failure.
99h Check for SMART drive (optional)
9Ah Shadow option ROMs
9Ch Set up Power Management
9Dh Initialize security engine (optional)
9Eh Enable hardware interrupts
9Fh Determine number of ATA and SCSI drives
A0h Set time of day
A2h Check key lock
A4h Initialize Typematic rate
A8h Erase F2 prompt
AAh Scan for F2 key stroke
ACh Enter SETUP
AEh Clear Boot flag
B0h Check for errors
B2h POST done- prepare to boot operating system
B4h 1 One short beep before boot
B5h Terminate QuietBoot (optional)
B6h Check password (optional)
B9h Prepare Boot
BAh Initialize DMI parameters
BBh Initialize PnP Option ROMs
BCh Clear parity checkers
BDh Display MultiBoot menu
BEh Clear screen (optional)
BFh Check virus and backup reminders
C0h Try to boot with INT 19
C1h Initialize POST Error Manager (PEM)
C2h Initialize error logging
C3h Initialize error display function
C4h Initialize system error handler
C5h PnPnd dual CMOS (optional)
C6h Initialize notebook docking (optional)
C7h Initialize notebook docking late
C8h Force check (optional)
C9h Extended checksum (optional)
D2h Unknown interrupt
Code Beeps POST Routine Description
Chapter 4 70
Code Beeps
E0h Initialize the chipset
E1h Initialize the bridge
E2h Initialize the CPU
E3h Initialize the system timer
E4h Initialize system I/O
E5h Check force recovery boot
E6h Checksum BIOS ROM
E7h Go to BIOS
E8h Set Huge Segment
E9h Initialize Multi Processor
EAh Initialize OEM special code
EBh Initialize PIC and DMA
ECh Initialize Memory type
EDh Initialize Memory size
EEh Shadow Boot Block
EFh System memory test
F0h Initialize interrupt vectors
F1h Initialize Run Time Clock
F2h Initialize video
F3h Initialize System Management Mode
F4h 1 Output one beep before boot
F5h Boot to Mini DOS
F6h Clear Huge Segment
F7h Boot to Full DOS
71 Chapter 4
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error Action in Sequence
LCD backlight doesn't work
LCD is too dark
LCD brightness cannot be adjusted
LCD contrast cannot be adjusted
Enter BIOS Utility to execute “Load Setup Default Settings”, then
reboot system.
Reconnect the LCD connectors.
Keyboard (if contrast and brightness function key doesn't work).
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
Unreadable LCD screen
Missing pels in characters
Abnormal screen
Wrong color displayed
Reconnect the LCD connector
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
LCD has extra horizontal or vertical lines
displayed.
LCD inverter ID
LCD inverter
LCD cable
LCD
System board
Indicator-Related Symptoms
Symptom / Error Action in Sequence
Indicator incorrectly remains off or on, but system
runs correctly
Reconnect the inverter board
Inverter board
System board
Power-Related Symptoms
Symptom / Error Action in Sequence
Power shuts down during operation Power source (battery pack and power adapter). See “Power
System Check” on page 60.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-on. Power source (battery pack and power adapter). See “Power
System Check” on page 60.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-off. Power source (battery pack and power adapter). See “Power
System Check” on page 60.
Hold and press the power switch for more than 4 seconds.
System board
Battery can’t be charged See “Check the Battery Pack” on page 62.
Battery pack
System board
Chapter 4 72
PCMCIA-Related Symptoms
Symptom / Error Action in Sequence
System cannot detect the PC Card (PCMCIA) PCMCIA slot assembly
System board
PCMCIA slot pin is damaged. PCMCIA slot assembly
Memory-Related Symptoms
Symptom / Error Action in Sequence
Memory count (size) appears different from
actual size.
Enter BIOS Setup Utility to execute “Load Default Settings, then
reboot system.
DIMM
System board
Speaker-Related Symptoms
Symptom / Error Action in Sequence
In Windows, multimedia programs, no sound
comes from the computer.
Audio driver
Speaker
System board
Internal speakers make noise or emit no sound. Speaker
System board
Power Management-Related Symptoms
Symptom / Error Action in Sequence
The system will not enter hibernation Keyboard (if control is from the keyboard)
Hard disk drive
System board
The system doesn't enter hibernation mode and
four short beeps every minute.
See “S4 Sleeping State” on page 26.
Press Fn+oand see if the computer enters hibernation mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
System board
The system doesn’t enter standby mode after
closing the LCD
See “S4 Sleeping State” on page 26.
LCD cover switch
System board
The system doesn't resume from hibernation
mode.
See “S4 Sleeping State” on page 26.
Hard disk connection board
Hard disk drive
System board
The system doesn't resume from standby mode
after opening the LCD.
See “S4 Sleeping State” on page 26.
LCD cover switch
System board
Battery fuel gauge in Windows doesn’t go higher
than 90%.
Remove battery pack and let it cool for 2 hours.
Refresh battery (continue use battery until power off, then charge
battery).
Battery pack
System board
73 Chapter 4
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined
Problems” on page 75.
System hangs intermittently. Reconnect hard disk/CD-ROM drives.
Hard disk connection board
System board
Peripheral-Related Symptoms
Symptom / Error Action in Sequence
System configuration does not match the
installed devices.
Enter BIOS Setup Utility to execute “Load Default Settings”, then
reboot system.
Reconnect hard disk/CD-ROM/diskette drives.
External display does not work correctly. Press Fn+F5, LCD/CRT/Both display switching
System board
USB does not work correctly System board
Print problems. Ensure the “Parallel Port” in the “Onboard Devices Configuration” of
BIOS Setup Utility is set to Enabled.
Onboard Devices Configuration
Run printer self-test.
Printer driver
Printer cable
Printer
System Board
Serial or parallel port device problems. Ensure the “Serial Port” in the Devices Configuration” of BIOS Setup
Utility is set to Enabled.
Device driver
Device cable
Device
System board
Keyboard/Touchpad-Related Symptoms
Symptom / Error Action in Sequence
Keyboard (one or more keys) does not work. Reconnect the keyboard cable.
Keyboard
System board
Touchpad does not work. Reconnect touchpad cable.
Touchpad board
System board
Modem-Related Symptoms
Symptom / Error Action in Sequence
Internal modem does not work correctly. Modem phone port
modem combo board
System board
Power Management-Related Symptoms
Symptom / Error Action in Sequence
Chapter 4 74
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1. Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRU.
3. If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
75 Chapter 4
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power
System Check” on page 60):
1. Power-off the computer.
2. Visually check them for damage. If any problems are found, replace the FRU.
3. Remove or disconnect all of the following devices:
TNon-Acer devices
TPrinter, mouse, and other external devices
TBattery pack
THard disk drive
TDIMM
TCD-ROM/Diskette drive Module
TPC Cards
4. Power-on the computer.
5. Determine if the problem has changed.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7. If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
TSystem board
TLCD assembly
Chapter 6 76
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of TravelMate 4060.
Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available
on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on
the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use
the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer
machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to
return it.
FRU (Field Replaceable Unit) List
Chapter 6
77 Chapter 6
TravelMate 4060 Exploded Diagram
TravelMate 4060 FRU List
Adapter
NS ADP 19V 3.42A PA-1650-02QR
90~264V LF
AP.06503.010
NS ADP 19V 3.42A SLS0335A19A57LF
90~264V EU
AP.06506.002
NS ADP 19V 3.42A SADP-65KB DBHF
90~264V LF
AP.06501.009
Battery
Chapter 6 78
NS BATTERY SANYO LI-ION 4S2P 4.4A
4UR18650F-2-QC140
BT.T5003.001
BATTERY PANASONIC LI-ION 4S2P
4.4A CGR-B/8B5AE
BT.T5005.001
BATTERY PANASONIC LI-ION 4S2P
4.4A ROHS
BT.00805.003
BATTERY SIMPPLO PACK LI-ION
4S1P 2.0A
BT.00407.001
BATTERY SANYO PACK LI-ION
4S1P 2.0A
BT.00403.004
BATTERY SONY PACK LI-ION 4S1P
1.96A
BT.00404.004
Board
NS MODEM 56K (MDC)T60M845.02 EU 54.TAKV7.001
NS BLUETOOTH MODULE W/ANTENNA 54.T48V7.001
NS W/L 802.11B/G(WM3B2200BGMW2) KI.CAX01.008
NS LAUNCH BOARD 55.TAKV7.001
NS TOUCH PAD BOARD 55.TAKV7.002
Cable
NS FFC CABLE - TP/B TO MB 50.A50V7.001
TravelMate 4060 FRU List
79 Chapter 6
NS MODEM CABLE 50.A510V7.001
NS POWER CORD US (3 PIN) 27.A03V7.001
POWER CORD PRC (3 PIN) 27.A03V7.003
POWER CORD KOERA ( Pin) 27.T23V7.006
POWER CORD EU (3 PIN) 27.A03V7.002
POWER CORD UK (3 PIN) 27.A03V7.004
POWER CORD ITALIAN (3 PIN) 27.A03V7.005
POWER CORD- SWISS 27.A03V7.007
POWER CORD AU (3 PIN) 27.A03V7.008
POWER CORD DANISH (3 PIN) 27.A03V7.006
POWER CORD AF (3 PIN) 27.T48V7.001
Case/Cover/Bracket Assembly
5MIDDEL COVER ERGO W/BUTTON -
LIGHT GREEN SILVER
42.T50V7.101
6UPPER CASE W/TOUCHPAD,
BRACKET, MIC,BLUETOOTH CABLE
60.T91V7.001
UPPER CASE W/TOUCHPAD,
BRACKET, MIC W/O BLUETOOTH
CABLE
60.T91V7.002
11 LOWER CASE W/SPEAKER 60.A51V7.002
13 DIMM/WIRELESS COVER 42.A50V7.001
HEATSINK COVER W/O DOCKING 42.A50V7.002
TravelMate 4060 FRU List
Chapter 6 80
NS 3 IN 1 DUMMY COVER 42.T51V7.003
15 HDD COVER 42.T63V7.004
14 HDD BRACKET 33.T50V7.001
Communication Module
NS WIRELESS LAN ANTENNA 50.T50V7.003
CPU/Processor
NS AMD MOBILE SEMPRON 2800+
25WD
KC.S2802.25D
AMD MOBILE SEMPRON 3000+
25WD
KC.S3002.25D
AMD MOBILE TURION 64 ML28 KC.TML02.280
AMD MOBILE TURION 64 ML30 KC.TML02.300
AMD MOBILE TURION 64 ML32 KC.TML02.320
AMD MOBILE TURION 64 ML34 KC.TML02.340
AMD MOBILE TURION 64 ML37 KC.TML02.370
Optical Disk Drive Module
NS DVD/CDRW COMBO MODULE 24X
PHILIPS SCB5265 LF
6M.A65V7.004
TravelMate 4060 FRU List
81 Chapter 6
NS DVD/CDRW COMBO DRIVE 24X
PHILIPS SCB5265 GB LF
KO.02403.007
NS OPTICAL DEVICE HOLDER-FIX 42.T51V7.003
NS DVD/CDRW BEZEL FOR G BASE 42.A65V7.003
DVD/CDRW COMBO MODULE KME
UJDA-770
6M.TAGV7.002
DVD/CDRW COMBO DRIVE 24X
KME UJDA-770
KO.02406.013
OPTICAL DEVICE HOLDER-FIX 42.T51V7.003
DVD/CDRW BEZEL FOR G BASE 42.A65V7.003
DVD/CDRW COMBO MODULE LITE-
ON SOSC-2483K LF
6M.ATKV7.001
DVD/CDRW COMBO LITE-ON
SOSC-2483K LF GB
KO.02409.011
OPTICAL DEVICE HOLDER-FIX 42.T51V7.003
DVD/CDRW BEZEL FOR G BASE 42.A65V7.003
DVD/CDRW COMBO MODULE HLDS
GCC-4244N LF
6M.ATKV7.002
DVD/CDRW COMBO HLDS GCC-
4244N GB LF
KO.0240A.004
OPTICAL DEVICE HOLDER-FIX 42.T51V7.003
DVD DUAL BEZEL G BASE 42.A65V7.003
DVD DUAL MODULE PANASONIC
UJ-840BAA2 G BASE
6M.A51V7.003
DVD DUAL DRIVE PANASONIC UJ-
840BAA2 D. LAYER G BASE
KU.00807.010
OPTICAL DEVICE HOLDER-FIX 42.T51V7.003
DVD DUAL BEZEL G BASE 42.A51V7.005
DVD DUAL MODULE LITE-ON
SOSW-833 DL G BASE
6M.T66V5.003
TravelMate 4060 FRU List
Chapter 6 82
DVD DUAL DRIVE LIET-ON SOSW-
833 DL G BASE
KU.00804.012
OPTICAL DEVICE HOLDER-FIX 42.T51V7.003
DVD DUAL BEZEL G BASE 42.A51V7.005
DVD DUAL MODULE PIONEER DVR-
K15RA F/W:1.05 G BASE
6M.ATKV7.003
DVD DUAL DRIVEPIONEER DVR-
K15RA D. LAYER F/W:1.05 G BASE
KU.00805.020
OPTICAL DEVICE HOLDER-FIX 42.T51V7.003
DVD DUAL BEZEL G BASE 42.A51V7.005
DVD DUAL MODULE HLDS GWA-
4082N G BASE
6M.ATKV7.004
DVD DUAL DRIVE HLDS GWA-
4082N G BASE
KU.0080D.016
OPTICAL DEVICE HOLDER-FIX 42.T51V7.003
DVD DUAL BEZEL G BASE 42.A51V7.005
HDD/Hard Disk Drive
NS 40G SEAGATE 2.5 IN. 4200RPM
N2.1ST9402113A (ROHS), F/W 3.01
KH.04001.016
40G TOSHIBA 2.5 IN. 4200RPM
PLUTO MK4025GAS (ROHS) F/W
KA100A
KH.04004.005
40G HGST 2.5 IN. 4200RPM
HAKONA-A F/W :A70G
KH.04007.013
40G WD 2.5 IN. 5400RPM ML40
WD400UE-22HCT0 (ROHS)
KH.04008.025
40G SAMSUNG 2.5 IN. 5400RPM
M40MP0402H (ROHS) F/W YQ200-
04
KH.0400B.003
60G SEAGATE 2.5 IN. 4200RPM
N2.2ST960812A F/W:3.04
KH.06001.003
60G TOSHIBA 2.5 IN. 4200RPM
PLUTO MK6025GAS (ROHS) F/W
KA200
KH.06004.004
60G HGST 2.5 IN. 4200RPM
HAKONE-A F/W :A70G
KH.06007.009
60G WD 2.5 IN. 5400RPM ML40
WD600UE-22HCT0 (ROHS)
KH.06008.002
80G SEAGATE 2.5 IN. 4200RPM
N2.2ST980829A F/W:3.04
KH.08001.013
80G TOSHIBA 2.5 IN. 4200RPM
PLUTO MK8025GAS (ROHS) F/W
KA023
KH.08004.003
TravelMate 4060 FRU List
83 Chapter 6
80G HGST 2.5 IN. 4200RPM
HAKONE-A F/W:A70G
KH.08007.011
80G WD 2.5 IN. 5400RPM ML40
WD800UE-22HCT0 (ROHS)
KH.08008.027
100G TOSHIBA 2.5 IN. 4200RPM
ARES MK1031GAS (ROHS) F/W
AA204A
KH.10004.001
100G HGST 2.5 IN. 4200RPM
HAKONE-A F/W:A70G
KH.10007.002
Keyboard
NS AS1680/AS1410 KEYBOARD
DARFON US International
KB.A2707.001
AS1680/AS1410 KEYBOARD
DARFON Chinese
KB.A2707.002
AS1680/AS1410 KEYBOARD
DARFON Spanish
KB.A2707.003
AS1680/AS1410 KEYBOARD
DARFON Thai
KB.A2707.004
AS1680/AS1410 KEYBOARD
DARFON Brazilian Protugese
KB.A2707.005
AS1680/AS1410 KEYBOARD
DARFON Korea
KB.A2707.006
AS1680/AS1410 KEYBOARD
DARFON UK
KB.A2707.007
AS1680/AS1410 KEYBOARD
DARFON German
KB.A2707.008
AS1680/AS1410 KEYBOARD
DARFON Italian
KB.A2707.009
AS1680/AS1410 KEYBOARD
DARFON French
KB.A2707.010
AS1680/AS1410 KEYBOARD
DARFON Swiss/G
KB.A2707.011
AS1680/AS1410 KEYBOARD
DARFON Portuguese
KB.A2707.012
AS1680/AS1410 KEYBOARD
DARFON Arabic
KB.A2707.013
AS1680/AS1410 KEYBOARD
DARFON Belgium
KB.A2707.014
AS1680/AS1410 KEYBOARD
DARFON Sweden
KB.A2707.015
AS1680/AS1410 KEYBOARD
DARFON Czech
KB.A2707.016
AS1680/AS1410 KEYBOARD
DARFON Hungaian
KB.A2707.017
AS1680/AS1410 KEYBOARD
DARFON Norway
KB.A2707.018
AS1680/AS1410 KEYBOARD
DARFON Danish
KB.A2707.019
AS1680/AS1410 KEYBOARD
DARFON Turkish
KB.A2707.020
TravelMate 4060 FRU List
Chapter 6 84
AS1680/AS1410 KEYBOARD
DARFON Canadian French
KB.A2707.021
AS1680/AS1410 KEYBOARD
DARFON Japanese
KB.A2707.022
AS1680/AS1410 KEYBOARD
DARFON Greek
KB.A2707.023
AS1680/AS1410 KEYBOARD
DARFON Hebrew
KB.A2707.024
AS1680/AS1410 KEYBOARD
DARFON Russian
KB.A2707.025
LCD Module
NS LCD 15.0 IN. MODULE SAMSUNG
LTN150XB-L03-V LF
6M.ATKV7.011
NS LCD 15.0 IN. XGA SAMSUNG
LTN150XB-L03-V LF
LK.15006.008
NS LCD INVERTER BOARD 19.TAKV7.001
NS LCD CABLE - 15 IN. XGA 50.T50V7.004
NS LCD BRACKET W/HINGE 15 IN. - L 33.T50V7.002
TravelMate 4060 FRU List
85 Chapter 6
NS LCD BRACKET W/HINGE 15 IN. - R 33.T50V7.003
NS LCD PANEL W/LOGO ANTENNA 14/
15 IN.
60.T50V7.102
NS LCD BEZEL W/RUBBER PAD 15 IN. 60.T50V7.004
LCD 15.0 IN. MODULE CMO N150X3-
L07 LF
6M.ATKV7.012
LCD 15.0 IN. XGA CMO N150X3-L07
REV C4 LF
LK.1500D.012
NS LCD INVERTER BOARD 19.TAKV7.001
NS LCD CABLE - 15 IN. XGA 50.T50V7.004
NS LCD BRACKET W/HINGE 15 IN. - L 33.T50V7.002
NS LCD BRACKET W/HINGE 15 IN. - R 33.T50V7.003
NS LCD PANEL W/LOGO ANTENNA 14/
15 IN.
60.T50V7.102
NS LCD BEZEL W/RUBBER PAD 15 IN. 60.T50V7.004
LCD 15.0 IN. MODULE LPL
LP150X07-TLA2 LF
6M.ATKV7.013
LCD 15.0 IN. XGA LPL LP150X07-
TLA2 LF
LK.15008.019
NS LCD INVERTER BOARD 19.TAKV7.001
NS LCD CABLE - 15 IN. XGA 50.T50V7.004
NS LCD BRACKET W/HINGE 15 IN. - L 33.T50V7.002
NS LCD BRACKET W/HINGE 15 IN. - R 33.T50V7.003
NS LCD PANEL W/LOGO ANTENNA 14/
15 IN.
60.T50V7.102
NS LCD BEZEL W/RUBBER PAD 15 IN. 60.T50V7.004
LCD 15.0 IN. MODULE LPL
LP150X07-TLA2 LF
6M.ATKV7.013
TravelMate 4060 FRU List
Chapter 6 86
LCD 15.0 IN. XGA LPL LP150X07-
TLA2 LF
LK.15008.019
LCD INVERTER BOARD 19.TAKV7.001
LCD CABLE - 15 IN. XGA 50.T50V7.004
LCD BRACKET W/HINGE 15 IN. - L 33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R 33.T50V7.003
LCD PANEL W/LOGO ANTENNA 14/
15 IN.
60.T50V7.102
LCD BEZEL W/RUBBER PAD 15 IN. 60.T50V7.004
NS LCD MODULE 15.4 IN. WXGA CMO
N154I1-L09
6M.A51V7.013
NS LCD 15.4 IN. WXGA CMO N154I1-
L09
LK.1540D.002
NS LCD INVERTER BOARD 19.TAKV7.001
NS LCD CABLE - 15.4 IN. XGA 50.T50V7.006
2LCD BRACKET W/HINGE 15.4 IN. - L 33.T50V7.004
3LCD BRACKET W/HINGE 15.4 IN. - R 33.T50V7.005
4LCD PANEL W/LOGO ANTENNA 14/
15 IN.
60.T50V7.102
1LCD BEZEL W/RUBBER PAD 15.4 IN. 60.T50V7.006
LCD 15.4 MODULE SAMSUNG
LTN154X3-L01-V104
6M.ATKV7.014
LCD 15.4 WXGA SAMSUNG
LTN154X3-L01-V104
LK.15406.009
LCD INVERTER BOARD 19.TAKV7.001
LCD CABLE - 15.4 IN. WXGA 50.T50V7.006
LCD BRACKET W/HINGE 15.4 IN. - L 33.T50V7.004
LCD BRACKET W/HINGE 15.4 IN. - R 33.T50V7.005
LCD PANEL W/LOGO ANTENNA
15.4 IN.
60.T50V7.103
LCD BEZEL W/RUBBER PAD 15.4 IN. 60.T50V7.006
LCD 15.4 MODULE QDI QD15TL02-
03 LF NON-GLARE
6M.ATKV7.015
LCD 15.4 WXGA QDI QD15TL02-03
LF NON-GLARE
LK.15409.004
LCD INVERTER BOARD 19.TAKV7.014
LCD CABLE - 15.4 IN. WXGA 50.T50V7.006
LCD BRACKET W/HINGE 15.4 IN. - L 33.T50V7.004
LCD BRACKET W/HINGE 15.4 IN. - R 33.T50V7.005
LCD PANEL W/LOGO ANTENNA
15.4 IN.
60.T50V7.103
LCD BEZEL W/RUBBER PAD 15.4 IN. 60.T50V7.006
LCD 15.4 IN. MODULE AU
B154EW01 V8 LF NON-G
6M.ATKV7.016
TravelMate 4060 FRU List
87 Chapter 6
LCD 15.4 IN. WXGA AU B154EW01
V8 LF NON-G
LK.15405.005
LCD INVERTER BOARD 19.TAKV7.001
LCD CABLE - 15.4 IN. WXGA 50.T50V7.006
LCD BRACKET W/HINGE 15.4 IN. - L 33.T50V7.004
LCD BRACKET W/HINGE 15.4 IN. - R 33.T50V7.005
LCD PANEL W/LOGO ANTENNA
15.4 IN.
60.T50V7.103
LCD BEZEL W/RUBBER PAD 15.4 IN. 60.T50V7.006
LCD 15.0 IN. MODULE SAMSUNG
LTN150XB-L03-V W/O WIRELESS
6M.ATKV7.021
LCD 15.0 IN. XGA SAMSUNG
LTN150XB-L03-V LF
LK.15006.008
LCD INVERTER BOARD 19.TAKV7.001
LCD CABLE - 15 IN. XGA 50.T50V7.004
LCD BRACKET W/HINGE 15 IN. - L 33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R 33.T50V7.003
LCD PANEL W/LOGO W/O
ANTENNA 14/15 IN.
60.T56V7.102
LCD BEZEL W/RUBBER PAD 15 IN. 60.T50V7.004
LCD 15.0 IN. MODULE CMO N150X3-
L07 LF W/O WIRELESS
6M.ATKV7.022
LCD 15.0 IN. XGA CMO N150X3-L07
REV C4 LF
LK.1500D.012
LCD INVERTER BOARD 19.TAKV7.001
LCD CABLE - 15 IN. XGA 50.T50V7.004
LCD BRACKET W/HINGE 15 IN. - L 33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R 33.T50V7.003
LCD PANEL W/LOGO W/O
ANTENNA 14/15 IN.
60.A56V7.102
LCD BEZEL W/RUBBER PAD 15 IN. 60.T50V7.004
LCD 15.0 IN. MODULE LPL
LP150X07-TLA2 LF W/O WIRELESS
6M.ATKV7.023
LCD 15.0 IN. XGA LPL LP150X07-
TLA2 LF
LK.15008.019
LCD INVERTER BOARD 19.TAKV7.001
LCD CABLE - 15 IN. XGA 50.T50V7.004
LCD BRACKET W/HINGE 15 IN. - L 33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R 33.T50V7.003
LCD PANEL W/LOGO W/O
ANTENNA 14/15 IN.
60.A56V7.102
LCD BEZEL W/RUBBER PAD 15 IN. 60.T50V7.004
LCD 15.4 MODULE QDI QD15TL02-
03 LF NON-GLARE W/O WIRELESS
6M.ATKV7.025
TravelMate 4060 FRU List
Chapter 6 88
LCD 15.4 WXGA QDI QD15TL02-03
LF NON-GLARE
LK.15409.004
LCD INVERTER BOARD 19.TAKV7.001
LCD CABLE - 15.4 IN. WXGA 50.T50V7.006
LCD BRACKET W/HINGE 15.4 IN. - L 33.T50V7.004
LCD BRACKET W/HINGE 15.4 IN. - R 33.T50V7.005
LCD PANEL W/LOGO ANTENNA
15.4 IN.
60.T56V7.103
LCD BEZEL W/RUBBER PAD 15.4 IN. 60.T50V7.006
LCD 15.4 IN. MODULE AU
B154EW01 V8 LF NON-G W/O
WIRELESS
6M.ATKV7.026
LCD 15.4 IN. WXGA AU B154EW01
V8 LF NON-G
LK.15405.005
LCD INVERTER BOARD 19.TAKV7.001
LCD CABLE - 15.4 IN. WXGA 50.T50V7.006
LCD BRACKET W/HINGE 15.4 IN. - L 33.T50V7.004
LCD BRACKET W/HINGE 15.4 IN. - R 33.T50V7.005
LCD PANEL W/LOGO ANTENNA
15.4 IN.
60.T56V7.103
LCD BEZEL W/RUBBER PAD 15.4 IN. 60.T50V7.006
Main Board
NS MAINBOARD 915GM UMA W/
PCMCIA W/O CPU MEMORY
LB.TAK02.001
Memory
NS MEMORY DDR333 256MB INFINEON
HYS64D32020HDL-6-C (.11u)
KN.25602.012
MEMORY DDR333 256MB NANYA
NT256D64SH8C0GM-6K
KN.25603.019
MEMORY DDR333 256MB
SAMSUNG M470L3224FT0-CB3
KN.2560B.008
MEMORY DDR333 256MB HYNIX
HYMD232M646D6-J
KN.2560G.001
MEMORY DDR333 512MB INFINEON
HYS64D64020HBDL-6-C (.11u)
KN.51202.025
MEMORY DDR333 512MB
SAMSUNG M470L6524BT0-CB3
KN.5120B.006
MEMORY DDR333 256MB HYNIX
HYMD564M646B6-J
KN.5120G.006
Speaker
TravelMate 4060 FRU List
89 Chapter 6
N/S SPEAKER SET 23.T50V7.001
Heatsink
10 THERMAL MODULE 60.A51V7.005
Miscellaneous
NS NAME PLATE - TM4060 1HYXZZZ24H9
NS RUBBER FOOT 1HYXZZZ24D6
NS LCD SCREW RUBBER PAD 47.T50V7.003
NS LCD BEZEL RUBBER PAD 47.T50V7.004
Screw
NS SCREW M2.0X3.0-I-NI-NYLOK 86.A03V7.012
NS SCREW I2.5*3M-BNIH(M2.5L3) 86.T25V7.012
NS SCREW M2.5*4L-BZN-NYLOK 86.A03V7.006
NS SCREW M2.0X5-I-NI-NYLOK 86.T23V7.006
NS SCREW MM25060IL69 86.A08V7.004
NS SCREW M2.0*5-I(NI)(NYLOK) 86.T23V7.010
NS SCREW M2.0X2.5-I-NI-NYLOK 86.A03V7.007
NS SCREW I2*3M-NIHY (M2L3) 86.T25V7.008
NS SCREW M1.7*3.0-I (BK) 86.T50V7.001
NS SCREW I3*3.5M-NIH(M3L3.5) 86.A03V7.011
TravelMate 4060 FRU List
Chapter 6 90

Navigation menu