ELITEGROUP COMPUTER SYSTEMS TC7A-W 7 inch Multi Function Pad User Manual Rev 01 170526
ELITEGROUP COMPUTER SYSTEMS CO., LTD 7 inch Multi Function Pad Rev 01 170526
User Manual-Rev.01(170526)
User Manual
7” Multi Function Pad
mPAD2-7-CHT4-I
Issue Date: 2017.03.22 v1.0
Copyright
The documentation and the software included with this product are copyrighted 2009 by
ECS(ELITEGROUP COMPUTER SYSTEM) Co., Ltd. All rights are reserved. ECS Co., Ltd.
reserves the right to make improvements in the products described in this manual at any time
without notice. No part of this manual may be reproduced, copied, translated or transmitted in
any form or by any means without the prior written permission of ECS Co., Ltd. Information
provided in this manual is intended to be accurate and reliable. However, ECS Co., Ltd.
assumes no responsibility for its use, nor for any infringements of the rights of third parties,
which may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Declaration of Conformity
FCC Class B
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Label Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Part No. 2014050100 Edition 1
Printed in China May 2014
mPAD2-7-CHT4-I Tablet PC User Manual ii
Caution! Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
Dispose of used batteries according to the manufacturer's
instructions
Warning! Any changes or modifications made to the equipment which are not
expressly approved by the relevant standards authority could void your
authority to operate the equipment.
Attention! Toute modification apportée à l'équipement qui n'est pas expressément
approuvé par l'autorité des normes pertinentes peuvent annuler votre
droit à faire fonctionner l'équipement.
Attention!
Danger d'explosion si la pile est remplacée de façon incorrecte.
Remplacez-la uniquement avec le même type ou équivalent recommandé par le fabricant.
Jetez les piles usagées selon les instructions du fabricant
RF Exposure Information (SAR) This device meets the government's requirements for exposure to radio
waves. This device is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal Communications Commission of
the U.S. Government. The exposure standard employs a unit of measurement known as the
Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR
are conducted using standard operating positions accepted by the FCC with the EUT
transmitting at the specified power level in different channels. The FCC has granted an
Equipment Authorization for this device with all reported SAR levels evaluated as in
compliance with the FCC RF exposure guidelines. SAR information on this device is on file
with the FCC and can be found under the Display Grant section of www.fcc.gov/eot/ea/fccid
after searching on FCC ID: WL6TC7A-W
iii mPAD2-7-CHT4-I Tablet PC User Manual
Packing List
Before setting up the system, check that the items listed below are included and in good
condition. If any items are missing, please contact your dealer immediately.
mPAD2-7-CHT4-I Pad x1
Strap x1
DC Charge Cable x1
HDMI Docking cable x1
USB3.0 Docking cable x1
Docking x1
MSR Module x1
SCR Module x1
Barcode scanner Module x1
USB Ethernet Module x1
Warning!
To prevent electric shock, Do not remove cover.
No user serviceable parts inside, refer servicing to qualified personnel.
Additional Information and Assistance
1. Visit the ECS websites at www.ecs.com.tw where you can find the latest information
about the product.
2. Contact your distributor, sales representative, or ECS's customer service center for
technical support if you need additional assistance. Please have the following
information ready before you call:
- Product name and serial number
- Description of your peripheral attachments
- Description of your software (operating system, version, application software, etc.)
- A complete description of the problem
- The exact wording of any error messages
- This equipment is a source of electromagnetic waves. Before use, please make
sure that there are not EMI sensitive devices in its surrounding which may
malfunction therefore
- Warning!
- 1. Input voltage rated 100
–
240Vac, 50-60 Hz, 1.0 – 0.5 A, Output Voltage
- rated 12Vdc / 3A
- 2.Use a 3.7V, 4100mAh Lithium0ion battery (Model No. MICA-071)
3. Maintenance: to properly maintain and clean the surfaces,
use only approved products or clean with a dry applicator
iv mPAD2-7-CHT4-I Tablet PC User Manual
Attention! Pour éviter un choc électrique, ne pas retirer le couvercle.
Aucune pièce réparable par l'utilisateur, voir l'entretien à du personnel
qualifié.
- Attention!
1. Tension de sortie Tension d'entrée nominale 100
–
240Vac, 50-60 Hz, 1.0
– 0.5 A, la note de 12Vdc / 3A
2.Utiliser un V @ 4100 mA Batterie Lithium-ion (modèle n ° LWN436789) 3.7
3. Entretien: bien entretenir et nettoyer les surfaces, utiliser uniquement des
produits approuvés ou nettoyer avec un applicateur sec
Caution!
This adapter Asian Power Devices Inc Type: WA-36A12RU-AAAG is a forming part of
the medical device.
IE IEC 60417 – 5009 : STAND-BY
IEC 60417 – 5031 : Direct Current
IEC 60417-5172 : ClassⅡequipment
Operation Instructions
Safety Instructions
Your system is designed and tested to meet the latest standards of safety for information technology
equipment. However, to ensure your safety, it is important that you read the following safety
instructions.
Setting up your system
• Read and follow all instructions in the documentation before you operate your system.
• Do not use this product near water or a heated source such as a radiator.
• Set up the system on a stable surface.
• Use this product in environments with ambient temperatures between 0°C and 35°C.
Attention during use
• Do not step on the power cord or let anything rest on top of it.
• Do not spill water or any other liquid on your system.
• When the system is turned OFF, a small amount of electrical current still flows. Always unplug all
power, modem, and network cables from the power outlets before cleaning the system.
• If you encounter the following technical problems with the product, unplug the power cord and contact
a qualified service technician or your retailer.
• The power cord or plug is damaged.
• Liquid has been spilled into the system.
• The system does not function properly even if you follow the operating instructions.
• The system was dropped or the cabinet is damaged.
• The system performance changes
Intend use
The equipment is intended for infant or adults by profession Health care professionals.
Mobile electronic medical records (EMR)
Move the image library
Mobile rounds
Move the drug
Mobile registration branch
v mPAD2-7-CHT4-I Tablet PC User Manual
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not
use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equipment and must
be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may
cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment from
overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the equipment to
the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything over the power
cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be opened only by
qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to the user's
manual.
e. The equipment has been dropped and damaged. f. The
equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE
TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60°C (140° F). THIS COULD
DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED
ENVIRONMENT.
16. If your computer is losing time significantly or the BIOS configuration resets itself to the
default, the battery may have no power.
vi mPAD2-7-CHT4-I Tablet PC User Manual
1. Do not replace battery yourself. Please contact a qualified technician or your retail
provider.
Caution! 2 .The computer is provided with a battery-powered real-time clock circuit. There is a
danger recommended by the manufacturer. Discard used batteries according to the
manufacturer's instructions.
1. Ne pas remplacer la batterie vous-même. S'il vous plaît contacter un technicien qualifié
Attention! ouvotre fournisseur de détail.
2. L'ordinateur est muni d'un circuit en temps réel de l'horloge alimentée par batterie. Il ya
un danger d'explosion si la pile est remplacée de façon incorrecte. Remplacez
uniquement par un type identique ou équivalent recommandé par le fabricant. Jetez les
piles usagées selon les instructions du fabricant.
17. CLASSIFICATION: Supply Class II adapter
(EDAC, EM1024PR)
No applied part
Continuous Operation
Not AP or APG category
18.Disconnect device: Removed the supply plug of direct plug–in adapter from the wall.
19.Follow national, state or local requirements to dispose of unit.
20.Maintenance: to properly maintain and clean the surfaces, use only the approved products or clean with a
dry applicator.
21.Contact information:
No.239, Sec. 2, Tiding Blvd., Neihu District, Taipei City 11493, Taiwan (R.O.C.).
TEL: +886 2-2162-1177
22.This equipment shall not be used as a life support system.
23. Accessory equipment connected to the analog and digital interfaces must be in compliance with the
respective nationally harmonized IEC standards (i.e. IEC
60950 for data processing equipment, IEC 60065 for video equipment, IEC
61010-1 for laboratory equipment, and IEC 60601-1 for medical equipment.) Furthermore all configurations
shall comply with the system standard IEC
60601-1-1. Anyone who connects additional equipment to the signal input part or signal output part is
configuring a medical system, and is therefore, responsible that the system complies with the requirements of
the system standard IEC
60601-1-1. The unit is for exclusive interconnection with IEC 60601-1 certified equipment in the patient
environment and IEC 60XXX certified equipment out- side of the patient environment. If in doubt, consult the
technical services department or your local representative.
24.Users must not allow SIP/SOPs to come into contact with the patient at the same time.
25.The sound pressure level at the operator's position according to IEC 704-1:1982
is no more than 70dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. ECS disclaims all responsibility for the
accuracy of any statements contained herein.
26. Turning off 7” multi function Pad, mPAD2-7-CHT4-M properly is important for system reliability.
There are two ways to turn off the system.
1. On the start menu, click “Shut down” and select “OK”
2. Push the power button and then the system will shut down automatically
mPAD2-7-CHT4-I Tablet PC User Manual vii
27. Product disposal notice
INPORTANT:
This symbol if the crossed out wheeled bin indicates that the product (electrical and
electronic equipment) should not be placed in municipal waste. Check local
regulations for disposal of electronic products.
28. mPAD2-7-CHT4 product service life is 3 Years.
29. The expected service life of the battery pack is expected to be approximately 3000 cycles.
This device has no shelf life, however the battery contained within has, therefore the device shall
be charged to full battery volume at least once every 6 months.
30. Do not modify this equipment without authorization of the manufacturer
31. The separable plug is used as isolation means, the device do not be positioned so that it is
difficult to disconnect device.
32. If power supply cord is optional in CCL, then need some statement in manual indicating user to
use suitable supply cord, ex medical grade and reliable grounding?
1. Grounding reliability can only be achieved when the equipment is connected to an
equivalent receptacle marked" Hospital Only" or "Hospital Grade".
2. Use a power cord that matches the voltage of the power outlet, which has been approved and
complied with the safety standard of your particular country.
33. Contact information:
ECS(ELITEGROUP COMPUTER SYSTEM) Co., Ltd.
No.239, Sec. 2, Tiding Blvd., Neihu District, Taipei City 11493, Taiwan (R.O.C.).
TEL: +886 2-2162-1177
FAX: +886 2-2797-0690
http://www.ecs.com.tw
mPAD-7-CHT4-I Tablet PC User Manual viii
Chapter 3 EMC TEST
REPORT.................................16
3.1 Description of Standards and Results for EN55022/EN5502.......... 17
Chapter 4
Troubleshooting.................................18
4.1 Solving Problems ...................... ......... ...................... ...................... 19
4.2 Troubleshooting Display Problems Solving Problems ...................... 19
4.3 Troubleshooting Audio Problems ........................................ 20
4.4 Clean tips ........................................ 20
Contents
Chapter 1 General Information ............................1
1.1 Introduction .............................................................................................. 2
1.2 Medical Application....................................................................................2
1.3 Specifications .......................................................................................... 2
T a b l e 1 . 1 : m P A D 2 - 7 - CHT4 - I S p e c i f i c a t i o n . . . . . 2
1.4 Cleaning/Disinfecting ............................................................................... 4
1.5 Dimensions .............................................................................................. 5
Figure 1.1 mPAD2-7-CHT4-I Dimensions ............... 6
Chapter 2 Getting Started.....................................7
2.1 A Q u ic k T o u r o f m P A D 2- 7 - C HT 4 - I . . . .. . . . . .. . . . . . . . .. . . . . 8
Figure 2.1 Front View ............................................................... 8
Figure 2.2 Left Side View........................................................... 8
Figure 2.3 Right Side View ....................................................... 9
Figure 2.4 Rear View ................................................................... 9
Figure 2.5 Top View ……........................................................... 10
2.2 A Quick Tour of mPAD2-7-CHT4-I Docking Station (Optional)............... 10
Figure 2.6 Rear View of Docking Station ..................................10
Figure 2.7 Strap ........................................................................ 10
2.3 Insert the USB Module into the mPAD2-7-CHT4 TABLET (Optional)…...... 11
2.4 Installation Procedures........................................................................... 12
2.4.1 Install the Strap (Optional).......................................................... 12
Figure 2.8 Install the Strap......................................................... 12
2.4.2 Insert / Hang the Stylus (Optional)............................................. 12
Figure 2.9 Stylus...................................................................... 12
Figure 2.10 Secure the stylus.................................................... 12
2.4.3 Insert the mPAD2-7-CHT4-I into the Docking Station (Optional) 13
Figure 2.11 Open and secure the protective cover.................... 13
Figure 2.12 mPAD2-7-CHT4-I in Docking Station.................. 13
2.4.4 Connecting the Power Cord for the Docking Station.................. 14
Figure 2.13 Connecting the AC Adapter Power Supplier to the
Docking Station………………………………………………....... 14
2.4.5 W arn i ng inf orm ation f or tab le us e. .................. 14
Figure 2.14 when table put into Dock...............................................15
Vi mPAD-7-CHT3-I Tablet PC User Manual
Chapter 1
1 General Information
The all new 7 " tablet from ECS are high performance tablets for professionals. Featuring an
IPx0 ingression-resistant housing that can be wiped with clean water for infection control and
80 cm drop resistance, mPAD2-7-CHT4 is designed for the healthcare environment. The
1D/2D barcode scanner supports positive patient identification and the 15Wh battery provides
uninterrupted use 5 hrs. mPAD2-7-CHT4 is secure for healthcare. Two factor authentication is
delivered through integrated NFC or optional USB smartcard accessories. Optional mobile
device management (MDM) solutions enable full control over applications, encryption,
connectivity and more on a single or group user level. With integrated WIFI, Bluetooth® 4.0,
mPAD2-7-CHT4 offers always-on connectivity in all environments. Retrieve patient data, view
lab results in real time and communicate with clinical team members using the integrated
cameras and microphone
Table 1.1: mPAD2-7-CHT4-I
Item
Description
Dimensions (WþDþH)
125 mm x 200 mm x 15.5 / 23.5 mm (bottom / top)
Weight
490g
CPU and Chipset
Intel Cherry Trail-T MSP Type4 Z8550
Memory
DDR3L 1600MHz
Graphics
Intel HD Graphics , Gen8-LP 16EU up to 650MHz
Max display resultion up to 2560 x 1600
7” LCD, Mipi ,1280 x 800 pixels
Audio
Realtek ALC5645
Internal Speaker x1
I/O Ports
1 x Mic/Head phone jack combo
1 x Micro SD card slot
1 x Docking Port (with AC-IN, HDMI, USB)
1 x USB3.0 micro type B
Display
7" TFT LCD Panel
Touch Panel
Support 10-points multi-touch(Capacitive)
Max. Resolution
1280 x 800 pixels
Stylus Pen
Active Stylus Pen
Storage
EMMC 32G/64G
Communication
WiFi- Wi-Fi 802.11 a/b/g/n/ac
Bluetooth 4.0 LE
NXP NPC100 ISO14443 Type A, Type B, PC/SC
(windows driver support )
Thermal Solution
Fan less Design
Operating System
Windows 10 Industry Pro 64Bits
Barcode Scanner
1D/2D Barcode scanner
1.1 Introduction
mPAD2-7-CHT4 is a multimedia Atom Mobile processor-based computer. It is a PC-based
system with 7" TFT LCD display and a stereo audio controller. mPAD2-7-CHT4 is a simple,
complete and highly integrated mobile multimedia system which allows system integrators to
easily build a Mobile Clinical Assistant Terminal into their applications.
Common industrial applications include factory automation systems, precision machinery,
and production process control. It is also suitable for many non-industrial applications,
including interactive kiosk systems, entertainment management, and car park automation.
mPAD2-7-CHT4-M is a reliable, cost-effective solution to meet an application’s processing
requirements.
1.3 Specifications
mPAD2-7-CHT4-I Tablet PC User Manual 2
Tablet PC User Manual 2
1.2 Medical Application
Camera
8.0 Mega pixel camera with LED light
Auto-focus supported
Web Camera
2.0 Mega pixel VGA camera
Frequency Stability
tolerance limit is +/- 20 ppm
Control Button
Power button: On the right side of mPAD2-7-CHT4-M
Barcode scanner buttons: On the Top side
Volume control button
Home Key button
Indicated LED
Power LED & Battery status LED
Full → Blue
Charging → Orange
Power Adapter
ADP WA-36A12RU-AAAG
Input voltage rated: 100-240Vac, 50-60Hz, 1.0-0.5A
Output voltage rated: 12Vdc, 3A
Battery
3 Hr charging time
Certification
FCC Part 15 Class B, CE, CB EN60950, IEC60601-1,
RoHS , WEEE (Documents ready only), BSMI, NCC
Battery Pack: UL2054, IEC62133, UN38.3
Environment Condition
Drop : 0.8m / 2.7ft. Drop to steel surface, 1drops per 6
sides
Vibration : 4Gs peak, 5Hz to 2kHz, 1 hour duration per
axis
Operating Temp : 0 ℃ to 35℃
Altitude: : 3,000 m
Storage / Transportation Temp : -20° C ~ +60° C
Storage / Transportation : 500 – 1013hpa
Operating Relative Humidity: 10% - 90%RH;
Storage/ Transportation Relative Humidity: 5% -
90%RH
Operation Pressure : 700 – 1013hpa
Transportation / Storage Pressure : 500 – 1013hpa
3 mPAD2-7-CHT4-I Tablet PC User Manual
1.4 Cleaning/Disinfecting
- During normal use mPAD2-7-CHT4-I may become soiled and should, therefore,
be cleaned regularly. Steps:
1. Wipe mPAD2-7-CHT4-I with a clean cloth that has been moistened in the cleaning water.
2. Prepare water per manufacturer’s instructions or hospital protocol.
3. Wipe thoroughly with a clean cloth.
Caution! Do not immerse or rinse mPAD2-7-CHT4-I or its peripherals. If you
accidentally spill liquid on the device, disconnect the unit from the power
source. Contact your Biomed personnel regarding the continued safety of the
unit before placing it back in operation.
Do not spray cleaning agent on the chassis.
Do not use disinfectants that contain phenol.
Do not autoclave or clean mPAD2-7-CHT4-I or its peripherals with strong
aromatic, chlorinated, ketone, ether, or other solvents, sharp tools or
abrasives. Never immerse electrical connectors in water or other liquids.
mPAD2-7-CHT4-I Tablet PC User Manual 4
PC User Manual 4
Attention! Ne pas immerger ou rincer mPAD2-7-CHT4-I ou ses périphériques. Si vous
renversez par accident un liquide sur l'appareil, débranchez l'appareil de la
source d'alimentation. Contactez votre Biomed concernant la sécurité
continue de l'unité avant de la remettre en service.
Ne pas pulvériser l'agent de nettoyage sur le châssis.
Ne pas utiliser de désinfectants contenant du phénol.
Ne pas passer à l'autoclave ou mPAD2-7-CHT4-I A propre ou ses
périphériques avec fortes, cétone, éther, ou d'autres solvants, des outils
tranchants ou abrasifs aromatiques chlorés. Ne jamais plonger connecteurs
électriques dans l'eau ou d'autres liquids.
1.5 Dimensions
5 mPAD2-7-CHT4-I Tablet PC User
Manual
Tablet PC User Manual
6 mPAD2-7-CHT4-I Tablet PC User
Manual
Tablet PC User Manual
Figure 1.1 mPAD2-7-CHT4-I Dimensions
Chapter 2
2 Getting Started
2.1 A Quick Tour of mPAD2-7-CHT4-I
Before you start to set up mPAD2-7-CHT4-I, take a moment to become familiar with the
locations and purposes of the controls, drives, connections and ports, which are illustrated in
the figures below.
When placed upright on the desktop, the mPAD2-7-CHT4-I front panel appears as shown in
Figure 2.1.
Figure 2.1 Front View
The card slots, USB3.0 Port and docking connector are on the Light side of the tablet PC.
Figure 2.2 Left Side View
mPAD2-7-CHT4-I Tablet PC User Manual 8
Tablet PC User Manual 8
Front camera
Light sensor
Indicated LED
Indicated LED
USB 3.0 Port
Card Slots
Docking Port
Hang Hole
Home Key
The volume control button, Power on button on the right side of the tablet PC.
The rear view of the tablet PC is depicted in Figure 2.4.
Figure 2.4 Rear View
9 mPAD2-7-CHT4-I Tablet PC User
Manual
User Manual
Figure 2.3 Right Side View
Power Button
Volume Button
Hang Hole
Rear camera
Small cover
Latch for release
module device
Middle cover
Speaker holes
TPU hand holder
The top side of the tablet PC contains headphone jack.
Figure 2.5 Top View
2.2 A Quick Tour of mPAD-7-CHT4-I Docking Holder
(Optional)
When you place the docking station on the desktop, its front panel appears as shown in Figure
2.6.
mPAD2-7-CHT4-I Tablet PC User Manual 10
PC User Manual 10
Docking connector
headphone jack.
Small cover
USB 3.0 Port
USB 2.0 Port
HDMI Port
DC-Jack Port
LAN Port
Figure 2.6 Rear View of Docking Station
2.3 Insert the USB Module into the mPAD2-7-CHT4-I
TABLET (Optional)
Step 1. Removed the small cover
Step 2. Insert the USB Module into the mPAD2-7-CHT4 TABLET
mPAD2-7-CHT4-M Tablet PC User Manual 11
PC User Manual 10
2.4 Installation Procedures
2.4.1 Install the Strap (Optional)
This strap is designed for the mPAD2-7-CHT4-I, which make the tablet convenient to hold.
12 mPAD2-7-CHT4-I Tablet PC User
Manual
Manual
Figure 2.7 Strap
2.4.2 Insert / Hang the Stylus Pen (Optional)
Figure 2.8 Install the Strap
Figure 2.9 Stylus Pen
mPAD2-7-CHT4-I Tablet PC User Manual 13
Figure 2.12 mPAD2-7-CHT4-I in Docking Station
2. Align the docking port to the docking connector to insert the tablet into the docking station
and press it right into position.
Note! Before placing the tablet into the docking station, please make sure that the
protective cover of docking port is placed right into its reserved slot.
Figure 2.11 Open and secure the protective cover
2.4.3 Insert the mPAD2-7-CHT4-I into the Docking Station (Optional)
1. Open and turn the protective cover of the docking port to the opposite side and press to
lock it into its reserved slot.
Figure 2.10 Secure the stylus Pen.
a. Hang and secure the stylus Pen through the hang hole of the mPAD2-7-CHT4-I
b. Insert and secure the stylus Pen onto the strap.
2.4.4 Connecting the Power Cord for the Docking Station
Be sure to always handle the power cords by holding the plug ends only. Follow
these procedures in order:
1. Insert the mPAD2-7-CHT4-I into the docking station as previous section 2.3.3.(See
Figure 2.13).
2. Connect the female end of the power cord to the DC-in jack of the docking station.
3. Connect the 2-pin male plug of the power cord to an electrical outlet.
Step 3
Step 2
Figure 2.13 Connecting the AC Adapter Power Supplier to the Docking Station
Note! The docking station is for mPAD2-7-CHT4-I battery charge only. Do not operate
the mPAD2-7-CHT4-I once it has been inserted into the docking station.
mPAD2-7-CHT4-I Tablet PC User Manual 14
DC-Jack Port
2.4.5 Warning information for table use.
2.4.5.1 Connect to HDMI monitor
2.4.5.2 Precautions for use with output port
Figure 2.14 when table put into Dock.
When table put into Dock, Connect to HMDI monitor, the display will not
show full screen on first time, please restart operation system, it will be
normal.
1. Connect dock port only, please use usb2.0 device or usb3.0 device.
2. Connect usb3.0 port only, please use usb2.0 device or usb3.0 device.
3. Connect dock port and usb3.0 port as same time, please use usb2.0
device, don’t use usb3.0 device.
4. Please don’t connect Dock port, usb3.0 port, module usb port as same
time, it will be safety consideration.
mPAD2-7-CHT4-I Tablet PC User Manual 15
Chapter 3
2 EMC TETEST REPORT
Chapter 3 EMC TEST REPORT
3.1 Description of Standards and Results for EN55022/EN55024
EMISSION
Description of Test Item
Standard
Limits
Results
Conducted disturbance
CISPR 11:2009+A1:2010
EN 55011:2009+A1:2010
Group 2, Class B
PASS
Minimum passing margin is 6.69dB at
0.158MHz
Radiated disturbance
(30-1000MHz)
CISPR 11:2009+A1:2010
EN 55011:2009+A1:2010
Group 2, Class B
PASS
Minimum passing margin is 3.10dB at
593.628MHz
Radiated disturbance
(Above 1GHz)
CISPR 11:2009+A1:2010
EN 55011:2009+
A1:2010
Group 2, Class B
PASS
Minimum passing margin is 3.22dB at
1482.48MHz
Harmonic current emissions
IEC 61000-3-2:2014
Class D
PASS
Voltage fluctuations & flicker
IEC 61000-3-3:2013
Section 5
PASS
IMMUNITY (EN 60601-1-2 2015)
Description of Test Item
Standard
Limits
Results
Electrostatic discharge (ESD)
IEC 61000-4-2: 2008
Section 6.2.1.10
PASS
Radiated RF electromagnetic
fields
IEC 61000-4-3: 2010
Section 6.2.1.10
PASS
Electrical fast transients and
bursts
IEC 61000-4-4: 2012
Section 6.2.1.10
PASS
Surge
IEC 61000-4-5: 2005
Section 6.2.1.10
PASS
Conducted disturbances,
induced by RF fields
IEC 61000-4-6: 2013
Section 6.2.1.10
PASS
Power frequency magnetic fields
IEC 61000-4-8: 2009
Section 6.2.1.10
PASS
Voltage dips
IEC 61000-4-11:2004
Section 6.2.1.10
PASS
Voltage interruptions
Section 6.2.1.10
PASSNOTE
N/A is an abbreviation for Not Applicable
NOTE: means a deviation from the requirement of EN 60601-1-2 Section 6.2.1.10), but it’s allowed.
mPAD2-7-CHT4-I Tablet PC User Manual 17
Chapter 4
Troubleshooting
Chapter 4 Troubleshooting
After Power on the TABLET for the first time you may experience some start up
problems. Before calling for technical support or returning for warranty, this chapter
may help to address some of the common questions using some basic troubleshooting tips.
4.1 Solving Problems
Follow these tips when you troubleshoot your computer:
• If you added or removed a part before the problem started, review the installation
procedures and ensure that the part is correctly installed.
• If a peripheral device does not work, ensure that the device is properly connected.
• If an error message appears on the screen, write down the exact message. This
Message may help support personnel diagnose and fix the problem(s).
• If an error message occurs in a program, see the program’s documentation.
Note: The procedures in this document were written for the Windows default view, so they may not
apply if you set your computer to the
Windows Classic view.
4.2 Troubleshooting Display Problems
Setting display background and icon properties:
1. Right-click the desktop anywhere except over an icon, then select Personalize from the pop-up menu.
2. From here, select the appropriate options to:
• Change the desktop background
• Select a screen saver
• Select colors and appearance options for icons and characters
• Set resolution and colors by using Display Settings options.
Problem: Ripple on screen
Troubleshooting and problem resolution:
1. Check for devices located less than one meter from the computer such as refrigerators, electric fans,
electric dryers, UPSs, regulators, fluorescent lamps or other computers that may be generating
magnetic interference.
2. Move any interfering devices away from the computer.
3. If the problem persists, consult with our Service.
mPAD2-7-CHT4-I Tablet PC User Manual 19
4.3 Troubleshooting Audio Problems
Problem: No sound from integrated speakers.
Troubleshooting and problem resolution:
• Adjust the windows volume control — Double-click the speaker icon in the
lower-right corner of your screen. Ensure that the volume is turned up and that the
sound is not muted. Adjust the volume, bass, or treble controls to eliminate distortion.
• Reinstall the audio driver.
• Disconnect headphones from the headphone connector — Sound from the
speakers is automatically disabled when headphones are connected to the computer’s
side-panel headphone connector.
Problem: No sound from headphones.
Troubleshooting and problem resolution:
• Check the headphone cable connection — Ensure that the headphone cable is
securely inserted into the headphone connector.
• Adjust the windows volume control — Click or double-click the speaker icon in
the lower-right corner of your screen. Ensure that the volume is turned up and that
the sound is not muted.
4.4 Clean tips
The following steps explains how to clean the panel:
1. When cleaning the computer, please make sure that the computer is switched off.
2. Put on gloves to prevent stains on the touch panel and prevent injured by the
sharp edge of the touch panel.
3. Do not hold FPC/Copper tail while handing the touch panel.
4. Do not pile up touch panel and put heavy matter on touch panel.
5. Do not add any stress on touch film.
6. Use dry cloth or soft cloth with water for clearing, the touch panel in case of dirt on it.
7. Do not use any organic solvents.
mPAD2-7-CHT4-I Tablet PC User Manual 20