ETI Solid State Lighting 90600120 Motion Sensor User Manual
Elec-Tech International Co., Ltd. Motion Sensor
User manual
Installing for Use with Direct Wired Fixtures (continued) Safety Information item #1000000000 Model #90600120 WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal. FCC ID:XZH-90600120 NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes / modifications not approved by the responsible party could void the user’s authority to operate the equipment. WARNING: Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker. Use and Care Guide Determining the knockout size Choose the appropriate knockout size for your fixture, either 3/4” or 1/2”, and use only the locknut and lock washer for that size. Feeding the wires Feed the electrical connection wires from the sensor module (A) through the selected knockout hole and then through the lock washer (BB/DD) followed by the locknut (AA/CC). NOTE: The lock washer (BB or DD) and locknut (AA or CC) should be on the inside of the fixture wall with the wires coming through the center of each. MOTION SENSOR MODULE Installing for use with selected Commercial Electric linkable plug-in LED light fixtures (continued) Care and Cleaning BB/DD CAUTION: Before attempting to clean the sensor, disconnect the power to the fixture by turning the breaker off or removing the fuse from the fuse box. If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation. BB/DD Connecting the sensor module to the fixture Ladder Gloves Pliers Package Contents Description Motion Sensor Module Quantity WHAT IS COVERED The manufacturer warrants this product to be free from defects in materials and workmanship for a period of five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or mishandling. Insert the threaded end of the sensor module (A) completely into the selected knockout hole and through the lock washer (BB/DD). Then tighten the locknut (AA/CC) securely onto the threaded end of the sensor module (A). AA/CC WHAT IS NOT COVERED This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and specifically disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor / expense costs involved in the replacement or repair of said product. Contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com. Part AA Description Making the electrical connections Connect the hot (black) wire from the sensor (A) to the black wire from the electrical box. Connect the neutral (white) wire from the sensor (A) to the white wire from the fixture and the white wire from the BB/DD electrical box. Connect the secondary live wire (red) from the sensor (A) to the live wire (black) from the fixture. Cover the three wire connections using the wire connectors (EE). BB Lock Washer (3/4 in.) CC Locknut (1/2 in.) DD Lock Washer (1/2 in.) EE Wire Connectors FF Male to Male Connector AA BB CC DD EE FF 1-877-527-0313 Homedepot.COM White WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker before beginning assembly or installation. NOTICE: This motion sensor module works with direct hard wired LED and fluorescent light fixtures as well as with selected Commercial Electric linkable plug-in LED light fixtures. Visit HomeDepot.com for a list of compatible Commercial Electric linkable plug-in fixtures. DIP 6 5 minutes Disabled DIP Switches AA/CC EE Red Black Replace the diffuser/lens on the light fixture. Restore power to the electrical box. Turn on the light switch to activate the fixture. Preparing the fixture Unplug the power cord from the electrical outlet and from the light fixture. Detection Area DIP 1 DIP 2 II III IV III III IV - Coverage By Install Height 10 ft. Ceiling 9 ft. Ceiling 8 ft. Ceiling 100% 43 ft. x 10 ft. 40 ft. x 9 ft. 39 ft. x 8 ft. 75% 36 ft. x 10 ft. 34 ft. x 9 ft. 33 ft. x 8 ft. 50% 26 ft. x 10 ft. 23 ft. x 9 ft. 23 ft. x 8 ft. 10% 7 ft. x 10 ft. 7 ft. x 9 ft. 7 ft. x 8 ft. Daylight sensor The daylight threshold can be adjusted by selecting the combination of settings on the DIP switches to determine the level of darkness when the light will turn on automatically. DIP 3 DIP 4 II III 5 sec. 90 sec. IV 100% 75% 50% 10% III III IV - 5 sec. 90 sec. 5 min. 15 min. III III IV - Disable 50 lux. 10 lux. 2 lux. 5 min. 15 min. DIP 5 DIP 6 II III Disable 50 lux. 10 lux. 2 lux. WARNING: Before doing any work on the motion sensor module, disconnect power to the light fixture. Minor problems often can be fixed without the help of an electrician. Connecting the sensor module to the fixture Insert the small male-to-male connector (FF) to the Power Out side of the sensor module (A). Push the other end of the male-to-male connector (FF) into the Power end of the fixture. Make sure both connections fit securely. NOTE: The sensor module (A) notes which end is Power In and which is Power Out. Installing for Use with Direct Wired Fixtures Preparing the fixture Remove the diffuser/lens to allow access to the fixture wiring. Remove the knockout where you wish to mount the sensor module. DIP 5 IV Installing for use with selected Commercial Electric linkable plug-in LED light fixtures Installation Black Attaching the diffuser to the housing NOTICE: The motion sensor can be used for fixtures installed up to 18 feet high. Questions, problems, missing parts? Before returning to the store, call Commercial Electric Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday DIP 4 Troubleshooting Quantity Locknut (3/4 in.) DIP 3 Hold-time Hold-time is the time period the light will remain on after the person has left the detected area. The amount of time the light remains on can be adjusted by selecting the combination of settings on the DIP switches for the desired hold-time. NOTICE: The green wire from the fixture should continue to be connected to the grounding wire from the electrical box. HARDWARE INCLUDED Daylight Sensor Light Level Hold-time Detection area The motion detection area can be adjusted by selecting the combination of settings on the DIP switches for the desired motion detection area. NOTE: For a firm fit, gently use pliers to tighten the locknut (AA/CC). Part DIP 2 75% Tools Required Warranty Detection Area: 75% Hold Time: 5 Minutes Daylight Sensor: Photocell Disabled To adjust the settings, simply move the DIP switches to the settings you prefer. NOTE: Keep your receipt and these instructions for proof of purchase. Safety Goggles The sensor comes from the factory with the following settings: Before beginning assembly, installation or operation of the product, make sure all parts are present. Compare parts with the package contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts. Wire Strippers Adjusting the Motion Sensor Motion Sensor Detection Area Insert the power cord firmly into the Power In end of the sensor module (A). Plug the power cord into the electrical outlet. Turn on the light fixture. DIP 1 Pre-Installation THANK YOU We appreciate the trust and confidence you have placed in Commercial Electric through the purchase of this motion sensor module. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Commercial Electric! Turning on the power AA/CC Clean the sensor with a soft, dry cloth. Do not use cleaners with chemicals, solvents, or harsh abrasives. Do not use liquid cleaner on the sensor. FCC ID: XZH-9050102016 FF Knockout holes FF Problem Possible Cause Solution The fixture will not light. The power is off. There is a bad connection. The motion sensor module is mounted higher than 18 ft. The wires are crossed or the power wire is grounding out. The hold-time setting needs to be adjusted. Ensure the power supply and circuit breaker are both in the on position. Check to ensure proper wire connections are made. Contact a qualified electrician. Mount the fixture with the motion sensor module at 18 ft. or lower. The fuse blows or the circuit breaker trips when the light is turned on. The light is not staying on long enough after the last motion is detected. Check the wire connections. Contact a qualified electrician or call Commercial Electric customer service 1-877-527-0313. Factory setting is a 5 minute hold time. To increase the time period the light remains on, please refer to the Adjusting the IV Motion Sensor section of the instruction manual to adjust the 4th dip switch to the preferred setting. The light is staying on too The hold-time setting Factory setting is a 5 minute hold time. To decrease the time n n long after the last motion is needs to be adjusted. period the light remains on, please refer to the Adjusting the II detected. Motion Sensor section of the instruction manual to adjust the 3rd and 4th dip switches to the preferred setting. The motion sensor is not The motion sensor needs To increase the motion detection area, please refer to the n n detecting motion in a large to be adjusted. Adjusting the Motion Sensor section of the instruction manual enough area. to adjust the 1st and 2nd dip switches to the preferred setting. The motion sensor is The motion sensor needs To decrease the motion detection area, please refer to the III detecting motion in too to be adjusted. Adjusting the Motion Sensor section of the instruction manual IV large an area. to adjust the 1st and 2nd dip switches to the preferred setting. The motion sensor is detecting motion during daylight hours and turning the light on when I do not need it on. The motion sensor is not detecting motion and turning the light on during daylight hours when I need it to. The daylight sensor needs Ensure the 5th and 6th dip switches are set to detect light at to be adjusted. the 50 lux, 10 lux or 2 lux settings. Please refer to the Adjusting the Motion Sensor section of the instruction manual to adjust the 5th and 6th dip switches to the preferred setting. The daylight sensor needs Ensure the 5th and 6th dip switches are set at “disable”. This to be adjusted. will allow the light to turn on when motion is detected at any light level. Please refer to the Adjusting the Motion Sensor section of the instruction manual to adjust the 5th and 6th dip switches to the preferred setting. II IV 5 sec. 90 sec. 100% 50% 10% 50 lux. III 15 min. 10 lux. 2 lux. Disable Instalación para uso con lámparas con cableado permanente (continuación) Informacíon sobre seguridad artículo # 1000000000 Modelo # 90600120 FCC ID:XZH-90600120 AVISO: Este aparato cumple con Parte 15 del reglamento FCC. Funcionamiento está sujeto a dos condiciones: (1) Este aparato puede no causar interferencia perjudicial, y (2) este aparato debe aceptar cualquier interferencia recibida, incluyendo la interferencia que pueda causar un funcionamiento no deseado. ADVERTENCIA: Los cambios o modificaciones que no estén expresamente aprobados por la parte responsable del cumplimiento anulan la autoridad del usuario de operar el equipo. ADVERTENCIA: Lea cuidadosamente y comprenda la información incluida en este manual antes de comenzar el armado e instalación. No hacerlo puede provocar descarga eléctrica, incendio, u otras lesiones que pueden ser graves or mortales. GUÍA DE USO Y CUIDADO ADVERTENCIA: Asegúrese de cortar el suministro eléctrico en los cables con los que trabajará. Extraiga los fusibles o apague el cortacircuitos. MÓDULO DETECTOR DE MOVIMIENTO Determine el tamaño de la tapa desprendible Echar cable Eche cables eléctricos para el módulo detector (A) a través del agujero de tapa seleccionado y luego a través de la arandela (BB/DD) seguido por la contratuerca (AA/CC). Elige el tamaño de tapa desprendible adecuado para su lámpara, ya sea de 3/4” o 1/2”, y use solo la contratuerca y la arandela para ese tamaño. NOTA: La arandela (BB o DD) y contratuerca (AA o CC) deben quedar en el interior de la lámpara con los cables entrando por el centro de cada uno. BB/DD Cuidado y limpieza NOTA: Guarde el recibo de compra y estas instrucciones como prueba de compra. Si no está familiarizado con las instalaciones eléctricas, le recomendamos que haga que un electricista calificado se ocupe de la instalación. Garantía HERRAMIENTAS NECESARIAS Guantes Pliers CONTENIDO DEL PAQUETE CUBRE El fabricante garantiza que este aparato de iluminación no tendrá defectos en los materiales o en la mano de obra por un periodo de cinco (5) años desde la fecha de compra. Esta garantía se aplica sólo al comprador consumidor original y sólo a los productos que se utilizan y reciben servicio en forma normal. Si se encuentra que este producto tiene defectos, la única obligación del fabricante, y su exclusiva solución, es reparar o reemplazar el producto a su entera discreción, siempre y cuando el producto no se haya dañado debido al mal uso, abuso, accidente, modificaciones, alteraciones, negligencias o mal manejo del mismo. Pieza Esta garantía no se aplica a ningún producto que se ha instalado incorrectamente, ajustado o utilizado en una forma que no concuerde con las instrucciones suministradas junto con el producto. Esta garantía no se aplicará a fallas del producto como resultado de un accidente, uso incorrecto, abuso, negligencia, alteración, instalación defectuosa, o ninguna otra falla no relacionada con el material o mano de obra defectuosa. Esta garantía no se aplica a la terminación en una parte del producto, tales como la superficie o la acción de los elementos, ya que esto se considera desgaste normal. El fabricante no garantiza y no acepta responsabilidad, ya sea, expresa o implícita de la idoneidad para un fin particular, a excepción de la garantía contenida en el presente. El fabricante niega específicamente responsabilidad y no será responsable por daños o pérdidas indirectas o consecuenciales, e incluye pero no se limita a los costos de mano de obra, gastos relacionados en el reemplazo o reparación de dicho producto. Módulo detector de movimiento Cantidad Inserte completamente la punta roscada del módulo detector (A) en el agujero de la tapa desprendible seleccionado y a través de la arandela (BB/DD). Entonces aprete fuerte la contratuerca (AA/CC) a la punta roscada del módulo detector (A). AA/CC Pieza Descripción Contratuerca (3/4 pulg.) Cantidad BB Arandela de presión (3/4 pulg.) CC Contratuerca (1/2 pulg.) DD Arandela de presión (1/2 pulg.) EE Conectores de cable FF Conector macho a macho AA BB CC DD EE FF Instalación ADVERTENCIA: RIESGO DE DESCARGA ELÉCTRICA. Asegúrese de cortar el suministro eléctrico en los cables con los que trabajará. O bien sacar el fusible o desconectar el disyuntor antes de empezar el montaje o instalación. Comuníquese con el equipo de Servicio al Cliente al 1-877-527-0313 o visite www.HomeDepot.com Conecte el cable fase (negro) del detector (A) al cable negro de la caja eléctrica. Conecte el cable neutro (blanco) del detector (A) con el cable blanco de la lámpara y el cable blanco de la caja elèctrica. BB/DD Conecte el cable secundario bajo tensión (rojo) del detector (A) con el cable bajo tensión (negro) de la lámpara. Cubre las tres conexiones de cable usando los conectores de cable (EE). Preparar el accesorio Desenchufe el cable eléctrico del enchufe eléctrico y de la lámpara. 1-877-527-0313 Homedepot.COM DIP 6 5 minutos Interruptores DIP Desactivado Área de detección El área de detección de movimiento puede ajustarse seleccionando la combinación de configuraciones en los interruptores DIP. Área de detección DIP 1 DIP 2 II III IV III III IV - Cobertura por altura de instalación Cielorraso de 10 pies Cielorraso de 9 pies Cielorraso de 8 pies 100% 43 pies x 10 pies 40 pies x 9 pies 39 pies x 8 pies 75% 36 pies x 10 pies 34 pies x 9 pies 33 pies x 8 pies 50% 26 pies x 10 pies 23 pies x 9 pies 23 pies x 8 pies 10% 7 pies x 10 pies 7 pies x 9 pies 7 pies x 8 pies Sensor de día El límite de día puede ajustarse seleccionando la combinación de opciones en los interruptores DIP para determinar el nivel de oscuridad cuando la luz se enciende automáticamente. DIP 3 DIP 4 II III 5 sec. 90 sec. IV 100% 75% 50% 10% III III IV - 5 sec. 90 sec. 5 min. 15 min. III III IV - Desactivado 50 lux. 10 lux. 2 lux. 5 min. 15 min. DIP 5 DIP 6 II III IV Desactivado 50 lux. 10 lux. 2 lux. Solución de problemas EE Rojo Negro Volve a colocar el difusor/lente a la lámpara. Reconecte suministro eléctrico. Prende luz con interruptor para activar la lámpara. Conectar el módulo detector a la lámpara Inserte el pequeño conector macho a macho (FF) al lado de salida de corriente del módulo detector (A). Empuje la otra punta del conector macho a macho (FF) en el extremo de entrada de corriente de la lámpara. Asegurarse que ambas conexiones están perfectamente encajadas. NOTA: El módulo detector (A) indica cual es el extremo de la entrada de corriente y cual la salida de corriente. Instalación para uso con lámparas con cableado permanente Preparación de lámparas Retire difusor/lente para permitir acceso al cableado de la lámpara. Retirer tapa desprendible Agujeros tapa desprendible donde se desee montar el módulo detector Blanco Instalación para uso con lámparas LED enchufables y conectables Commercial Electric DIP 5 ADVERTENCIA: Antes de realizar cualquier trabajo en la lámpara, desconecte la electricidad que la alimenta. Los problemas menores pueden arreglarse sin ayuda de un electricista. AVISO: El detector de movimiento puede ser utilizado en lámparas hasta una altura de 5,5 m. Negro Acoplar difusor a caja AVISO: Este módulo detector de movimiento funciona con lámparas LED y fluorescente con cableado permanente, como también con lámparas LED enchufables y conectables Commercial Electric selectas. Visite HomeDepot.com para obtener una lista de lámparas enchufables y conectables Commercial Electric compatibles. ¿Preguntas, problemas, piezas faltantes? Antes de devolver el producto a la tienda, llame al Centro de Atención al Cliente de Commercial Electric en el horario de 8 a.m. – 7 p.m., Hora del Este de EE.UU., de lunes a viernes. 9 a.m. – 6 p.m., Hora del Este de EE.UU., sábados. AA/CC DIP 4 Tiempo de encendido El tiempo de encendido es el periodo que la luz permanece encendida después de que la persona deja el área de detección. El periodo que la luz permanece encendida puede ajustarse seleccionando la combinación de opciones en el interruptor DIP por el tiempo deseado. Hacer las conexiones eléctricas DIP 3 Para ajustar la configuración, mueva los conmutadores DIP a su configuración preferida. BB/DD Conectar el módulo detector a la lámpara AVISO: El cable verde de la lámpara debe seguir conectado al cable de tierra de la caja eléctrica. MATERIALES INCLUIDOS AA NO CUBRE Descripción DIP 2 Nivel de luz del sensor durante el día Tiempo de encendido NOTA: Para que quede bien fuerte, user alicates para apretar la contratuerca (AA/CC). Escalera Área de detección: 75% Tiempo de encendido: 5 minutos Sensor de día: Fotocelda desactivada 75% Antes de comenzar el armado, instalación u operación del producto, asegúrese de que tiene todas las piezas. Compare las piezas con la lista de contenido. Si alguna de las piezas faltara o estuviera dañada, no proceda a armar, instalar u operar el producto. Comuníquese con el servicio al cliente para consultar por las piezas de reemplazo. Gafas de seguridad Ajustar el detector de movimiento Área de detección del sensor de movimiento Previo a la instalacíon Inserte el cable eléctrico en el extremo de entrada de corriente del módulo detector (A). Enchufe el cable eléctrico en el enchufe eléctrico. Prende la lámpara. DIP 1 Limpie el detector con un paño suave y seco. No utilice limpiadores con productos químicos, solventes o abrasivos. No use producto de limpieza líquido sobre el detector. Alicates pelacables Prender la corriente AA/CC PRECAUCIÓN: Antes de limpiar el aparato, desconecte el suministro eléctrico hacia este apagando el cortacircuitos o extrayendo el fusible de la caja de fusibles. GRACIAS Apreciamos la confianza que ha puesto en Commercial Electric a través de la compra de este módulo detector de movimiento. Nos esforzamos por crear constantemente productos diseñados para realzar su hogar. Visítenos en línea para ver uestra gama completa de productos disponibles para sus necesidades al momento de hacer mejoras en su hogar. ¡Muchas gracias por elegir a Commercial Electric! El detector viene de fábrica con la siguiente configuración: FCC ID: XZH-9050102016 Instalación para uso con lámparas LED enchufables y conectables Commercial Electric (continuación) FF FF Problema Posible causa Medida correctiva La lámpara no enciende. El suministro eléctrico está cortado. Mal conexión de cables. Asegurarse que el suministro eléctrico y el disyuntor estan ambos en la posición “on”. El módulo detector de movimiento se monta por encima de 5,5 m. El fusible se quema o salta Los cables están cruzados el cortacircuitos cuando se o el cable de suministro enciende la lámpara. eléctrico no está puesto a tierra. La luz no permanece Debe ajustarse la encendida el tiempo suficiente configuración del tiempo después de la detección del de encendido. último movimiento. La luz permanece encendida Debe ajustarse la demasiado tiempo después de configuración del tiempo la detección del último de encendido. movimiento. El sensor no detecta Debe ajustarse el sensor movimiento en una superficie de movimiento. lo suficientemente grande. El sensor detecta movimiento Debe ajustarse el sensor en una superficie demasiado de movimiento. grande. El sensor detecta movimiento Debe ajustarse el sensor durante las horas del día y la de luz de día. luz se enciende cuando no la necesito. El sensor no detecta Debe ajustarse el sensor movimiento y la luz se de luz de día. enciende cuando no la necesito. Revise para asegurarse de que se hayan conectado los cables de forma correcta. Comuníquese con un electricista calificado. Monte la lámpara con el módulo detector de movimiento a 5,5 m, o más abajo. Verique las conexiones de los cables. Comuníquese con un electricista calificado o llame al Centro de Atención al Cliente de Commercial Electric 1-877-527-0313. La configuración de fábrica es de un tiempo de encendido de 5 minutos. Para aumentar el tiempo que la luz permanece encendida, consulte la sección de ajustar el detector de movimiento del manual de instrucciones para ajustar el 4° interruptor dip a su configuración preferida. La configuración de fábrica es de un tiempo de encendido de 5 minutos. Para reducir el tiempo que la luz permanece encendida, consulte la sección de ajustar el detector de movimiento del manual de instrucciones para ajustar el 3° y 4° conmutadores DIP a su configuración preferida. Para aumentar la superficie de detección de movimiento, consulte la sección de ajustar el detector de movimiento del manual de instrucciones para ajustar el 1° y 2° conmutadores DIP a su configuración preferida. Para reducir la superficie de detección de movimiento, consulte la sección de ajustar el detector de movimiento del manual de instrucciones para ajustar el 1° y 2° conmutadores DIP a su configuración preferida. Asegúrese de que los interruptores 5to. y 6to. están configurados para detectar luz a 50 lux, 10 lux o 2 lux. Consulte la sección de ajustar el detector de movimiento del manual de instrucciones para ajustar el 5° y 6° conmutadores DIP a su configuración preferida. Asegúrese de que los interruptores 5to. y 6to. están configurados en “desactivado”. Esto permitirá que se encienda la luz cuando se detecta movimiento en cualquier nivel de luz. Consulte la sección de ajustar el detector de movimiento del manual de instrucciones para ajustar el 5° y 6° conmutadores DIP a su configuración preferida. IV 15 min. II III 100% 50% IV II 10% 50 lux. III IV 5 sec. 90 sec. 10 lux. 2 lux. Desactivado This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes : ( 1 ) Ce dispositif ne peut causer d'interférences ; et ( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Create Date : 2016:09:08 10:43:28-04:00 Metadata Date : 2017:05:02 15:39:32+08:00 Modify Date : 2017:05:02 15:39:32+08:00 Creator Tool : Adobe InDesign CS6 (Macintosh) Instance ID : uuid:7a9a10b2-24de-4307-94f8-b9a47f2de3a6 Original Document ID : xmp.did:8AD96A8E1B5EE111B334FF5301E28B9B Document ID : xmp.id:E820CDE91B206811822A96912E76E5AA Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:E720CDE91B206811822A96912E76E5AA Derived From Document ID : xmp.did:8488F6C636206811822A946EAA326028 Derived From Original Document ID: xmp.did:8AD96A8E1B5EE111B334FF5301E28B9B Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Macintosh) History Changed : / History When : 2016:09:08 10:43:28-04:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 3 Creator : Adobe InDesign CS6 (Macintosh)EXIF Metadata provided by EXIF.tools