ELITEGROUP COMPUTER SYSTEMS 6000IABG Notebook User Manual 600 E V1

Elitegroup Computer Systems Co., Ltd Notebook 600 E V1

Contents

Users Manual 1

i
i Preface Copyright 2004 All Rights Reserved. The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer. Trademarks AutoCAD and Autoshade are trademarks of Autodesk, Inc. IBM, OS/2, and VGA are trademarks of International Business Machines Corp. Lotus, 1-2-3, and Symphony are trademarks of Lotus Development Corp. Windows, Word, MS-DOS, and Microsoft are trademarks of Microsoft Corp. VESA is a trademark of Video Electronics Standards Association. Other product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies. Limitation of Liability While reasonable efforts have been made to ensure the accuracy of this manual, the manufacturer and distributor assume no liability resulting from errors or omissions in this manual, or from the use of the information contained herein. 600
ii Notices Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio TV technician for help Notice: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Shielded interface cables and a non-shielded AC power cord must be used in order to comply with emission limits. This equipment is to be used with power supply: I/P: 100-240 Vac, 50-60Hz, 1.5A O/P: 19Vdc, 4.74A There is no internal power supply.
iii Table of Content Chapter 1: Before you Start----------------------------------------------- 1 Conventions of This Manual........................................................................ 1 Safety Precautions ....................................................................................... 1 Wichtige Sicherheitshinweise .................................................................... 3 Things you must remember before working on your computer............... 6 Chapter 2: Introduction ---------------------------------------------------- 9 Welcome to the Notebook PC.................................................................... 9 Unpacking the Notebook............................................................................. 9 Getting to Know Your Computer................................................................ 10 Chapter 3: Getting Started------------------------------------------------- 19 Connecting to a Power Source.................................................................... 19 Turning On Your Notebook Computer....................................................... 20 Inserting and Removing the Battery Pack.................................................. 21 Charging the Battery Pack........................................................................... 23 Chapter 4: Using the Notebook Computer ----------------------------- 24 Adjusting the LCD Screen Display............................................................. 24 The TouchPad ............................................................................................... 28 Data Storage and Retrieval .......................................................................... 28 Power Saving Modes.................................................................................... 29 Resetting the System................................................................................... 33 Chapter 5: Desktop Operation -------------------------------------------- 35 Audio............................................................................................................. 35 Connecting Peripheral Devices .................................................................. 36 Chapter 6: Internet Connection ------------------------------------------ 39 Using Both DHCP and Static IP for Connection to Internet.................... 40 Using Wireless LAN Network for Connection to Internet (Microsoft’s Service Pack 2) (Optional).......................................................................... 42 Chapter 7: Configuring and Maintaining your System--------------- 43 Introduction.................................................................................................. 43 Chapter 8: Microsoft Center Edition (MCE) (Option) --------------- 51 Windows XP Media Center Edition (MCE) .............................................. 51 MCE Application Sound Adjustment.......................................................... 52 If you are using MCE’s “My TV” application............................................ 52 If you are using InterVideo’s WinDVR application.................................. 53 Chapter 9: VGA Utilities---------------------------------------------------- 55
iv ATI OpenGL.................................................................................................. 56 ATI’s Display................................................................................................ 56 Color ............................................................................................................. 58 Options.......................................................................................................... 59 Overlay.......................................................................................................... 60 ATI PowerPlay.............................................................................................. 61 Direct 3D...................................................................................................... 62 Chapter 10: Viewing Live Video (Option) ------------------------------- 63 Using the Remote Control .......................................................................... 64 WinDVR Mode............................................................................................. 64 Application buttons in DVR mode.............................................................. 66 Application buttons in DVD mode.............................................................. 68 Application buttons in Music mode............................................................ 71 Chapter 11: Troubleshooting --------------------------------------------- 73 Locating a Problem...................................................................................... 73 Checking Cables and Connections.............................................................. 73 The Power-On Self Test .............................................................................. 74 General Hardware Problems ....................................................................... 75 Contacting Your Dealer............................................................................... 77 Chapter 12: How do I Expand my Notebook-------------------------- 79 Upgrading your Memory............................................................................. 80 Easy to Upgrade HDD Module ................................................................... 81 Chapter 13: Specification -------------------------------------------------- 83 Detailed Notebook Specifications ............................................................. 83
v Canadian DOC Notice For Class B Computing Devices This Class B digital apparatus meets all requirements of the Canadian Interference - Causing Equipment Regulations. Cet appareil numerique de la classe B repecte toutes les exigences du Règlement sur le matèriel brouilleur du Canada. Personal Inventory This Notebook computer system is designed for years of productive and pleasurable computing. Use this section to keep notes about details of your purchase. Update this section when you add new options. Date of Purchase: Dealer’s Name: Phone: Address: E-Mail Address: WWW Site: Serial Number: CPU Type: Hard Disk Capacity: Memory Capacity: Optional Equipment:
1 BEFORE YOU START Conventions of This Manual Use this manual will help you get the most from your notebook computer. • If you are an experienced user of computers and/or Microsoft’s Windows operating systems, you might find it useful to read the Quick Start Guide that comes along with your accessories. • If you are a less experienced user, you should through the manual carefully before using your system. Whether or not you are an experienced user, you should consult on the Troubleshooting Chapter if you encounter any problems with your notebook. Safety Precautions This section is designed to assist you in identifying potentially unsafe conditions while working with this product. Required safety features have been installed in the computer to protect you from injury. However, you should use good judgment to identify potential safety hazards: 1. Please read these safety instructions carefully. 2. Please keep this User's Manual for later reference. 3. Please disconnect this equipment from AC outlet before cleaning. Don't use liquid or sprayed detergent for cleaning. Use moisture sheet or cloth for cleaning. 4. For pluggable equipment, that the socket-outlet shall be installed near the equipment and shall be easily accessible. 5. Please keep this equipment from humidity. 6. Lay this equipment on a reliable surface when installed. A drop or fall could cause injury. 7. Make sure to use the right voltage for the power source when connecting the equipment to the power outlet.
2 8. Place the power cord in such a way that people can not step on it. Do not place anything on top of the power cord. 9. All cautions and warnings on the equipment should be noted. 10. If the equipment is not use for a long time, disconnect the equipment from the main power outlet to avoid being damaged by transient overvoltage. 11. Never pour any liquid into the opening, this could cause fire or electrical shock. 12. Never open the equipment. For safety reason, the equipment should only be opened by a qualified service personnel. 13. If on the following situations arises, get the equipment checked by a service personnel: a. The Power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment has not worked well or you cannot get it work according to the user's manual. e. The equipment has dropped and damaged. f. If the equipment has obvious sign of breakage. 14. Do not leave this equipment in an environment unconditioned, storage temperature above 60°C (140°f), it may damage the equipment. 15. The unit can be operated at an ambient temperature of max. 35°C. 16. The sound pressure level at the operators position according to IEC 704-1: 1982 is equal or less than 70 dB(A). 17. Power Cord Requirements The power cord set used with the AC adaptor must meet the requirements of the country where you use the AC adaptor, whether it is 100-120 or 200-240 Vac. The following information explains the requirements for power cord set selection. Ø The cord set must be approved for the country in which it is used. Ø The appliance coupler must have a configuration for mating with a CEE22/EN6032/IEC 320 appliance inlet. A. For U.S. and Canada: Ø The cord set must be UL Listed and CSA Certified. Ø The minimum specifications for the flexible cord are No. 18 AWG. B. For Japan:
3 Ø All components of the cord set must bear a “PSE” or “ T ” mark and registration number in accordance with the Japanese Dentori Law. Ø The minimum specifications for the flexible cord are .75m㎡ conductors. C. For Other Countries: Ø The cord set fittings must bear the certification mark of the agency responsible for evaluation in a specific country. Ø The flexible cord must be of a HAR (harmonized) type H05VV-F. Ø The cord set must have a current capacity of a least 2.5 Amperes and voltage rating of 125 or 250 Vac. 18. When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons. These precautions includes the following: • Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. • Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. • Do not use the telephone to report a gas leak in the vicinity of the leak. • Use only the power cord indicated in this manual. 19. Do not use the AC adapter near open water or other liquids. Never spill liquid into the AC adapter. 20. Laser Warning: Laser Class I Product Caution - Invisible laser radiation when open avoid exposure to beam. 21. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Never remove the battery pack while the power is on as this may result in data loss when the system loses power. 22. The input receptacle is used as the main disconnecting device. Wichtige Sicherheitshinweise 1. Bitte lesen Sie diese Hinweis sorgfältig durch. 2. Heben Sie dirse Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen.
4 Versenden Sie Keine Flüssig- oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung. 4. Die Netzanschlußsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte Beschädigungen hervorrufen. 7. Beachten Sie beim Anschluß an das Stromnet die Anschlußwerte. 8. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte auch nichts auf der Leitun abgestellt werden. 9. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten. 10. Wird das Gerät üeinen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden. 11. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeien in das Gerät gelangen. Dies könne einen Brand bzw. Elektrischen Schlag auslösen. 12. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von authorisiertem Servicepersonal geöffnet werden. 13. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu Überprüfung.: a. Netzlabel oder Netzstecker sind beschädigt. b. Flüssigkeit ist in das Gerät eingedrungen. c. Das Gerät war Feuchtigkeit ausgesetzt. d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen. e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt. f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist. 14. VORSICHT: Explosiongsgetahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ähnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers. 15. Dieses Schaltnetzteil kann bis zu einer Außentemperatur von maximal 35ºC. 16. Die Ausgangswerte dürfen nicht die auf dem Label angegebenen Werte überschreiten. 17. Anforderungen an das Stromkabel
5 Das Kabel-Set, das an das Netzteil angeschlossen wird, muss den Anforderungen des Landes, in dem Sie das Netzteil einsetzen, genügen, je nachdem, ob die Netzspannung 100-120 oder 200-240V Wechselspannung beträgt. Ø Das Kabel-Set muss für das Land, in dem es eingesetzt wird, zugelassen sein. Ø Der Gerätestecker des Kabels muss in eine CEE22/ EN603/ IEC 320 Buchse passen. A. Für die USA und Kanada: Ø Das Kabel-Set muss UL-gelistet und CSA zertifiziert sein. Ø Die Minimalanforderungen für das Kabel entsprechen No. 18 AWG. B. Für Japan: Ø Alle Teile des Kabel-Sets müssen entsprechend dem japanischen Dentori Law mit einem „PSE“ or „T”-Symbol markiert sein Ø Die Minimalanforderungen für das Kabel sind .75m ㎡ Leiter. C. Für andere Länder: Ø Die Zubehörteile des Kabel-Sets müssen das Prüfsiegel derjenigen Stelle, die in dem jeweiligen Land für die Sicherheitsprüfung zuständig ist, tragen. Ø Das Kabel muss vom HAR (harmonisierten) Typ H05VV-F sein. Ø Das Kabel-Set muss eine Stromkapazität von mindestens 2,5 Ampere haben und Spannungen von 125 oder 250 V Wechselstrom gestatten. 18. Bei der Benutzung Ihres Telefongerätes sollten Sie immer die grundlegenden Sicherheitsmaßnahmen beachten, um das Risiko von Feuer, Stromschlägen und Verletzungen zu minimieren. Zu beachten sind u.a. folgende Punkte: • Benutzen Sie das Gerät nicht in der Nähe von Wasser, wie zum Beispiel Badewanne, Waschbecken, Spülbecken, Waschbottich, in feuchten Kellerräumen oder in der Nähe von Schwimmbecken. • Benutzen Sie kein Telefon (ausgenommen schnurlose Modelle) während eines Gewitters. Es besteht das geringe Restrisiko eines Blitzschlages.
6 • Benutzen Sie das Telefon nicht um ein Gasleck zu melden, falls es sich in der Nähe des Lecks befindet. • Benutzen Sie nur solch ein Stromkabel, wie in dieser Anleitung beschrieben. 19. Benutzen Sie das Netzteil nicht in unmittelbarer Nähe zu Wasser oder anderen Flüssigkeiten. Gießen Sie nie Flüssigkeiten über das Netzteil. 20. Achtung Laser: Laser Produkt der Klasse I. Achtung - Unsichtbarer Laserstrahl, vermeiden Sie Kontakt mit dem Strahl bei offenem Gehäuse. 21. Es besteht Explosionsgefahr, wenn der Akku nicht ordnungsgemäß ersetzt wird. Ersetzen Sie den Akku nur durch einen Akku gleichen oder äquivalenten Typs, der vom Hersteller empfohlen wird. Entsorgen Sie Akkus entsprechend den Anweisungen des Herstellers. Entfernen Sie den Akku auf keinen Fall bei eingeschaltetem Notebook, da hierdurch Daten verloren gehen könnten. 22. Der Netzeingabeanschluss dient als Hauptschalter des Geräts. Things you must remember before working on your computer Let your computer acclimate itself Your notebook can easily stand temperature extremes but it doesn’t like rapid changes in temperature, like going from the cold outdoors to a warm office. Rapid changes in temperature can cause water droplets to condense inside your case, threatening to damage the electronic parts inside. After receiving your notebook when it’s hot or cold outside, try not to power up the computer immediately, let the computer adjust to the room temperature gradually at least for three to four hours. If your system arrives in cold weather, do not apply power to the computer or monitor until they have been allowed to come to room temperature. Heat, Cold, Humidity, and Glare Find a suitable place for your computer that’s not too hot, too cold, too dark, or too bright. Glare can make it hard to read the screen.
7 • Try to avoid the computer components from being destroyed if it is over heated, so try to allow plenty of room for air to circulate around the case. • Do not block the ventilation opening. • Do not place your computer in direct sunlight. Suitable place to work Your computer will run well wherever you’re comfortable but extremes of temperature and humidity can be challenging to your system’s parts. There are some things you can tolerate that the computer can’t – things like static electricity, dust, water, steam and oil. In case you decide to pull over for roadside computing, try to choose a clean, comfortable work area for your system. A lithium-ion battery pack will be available when you are traveling. If you are running your system for the first time on battery power, remove the battery from the package, install it into the system and recharge the battery to fully prepare for service.
8
9 INTRODUCTION Welcome to the Notebook PC Congratulations on your purchase of the Notebook PC. Your Notebook features the latest advances in portable computing technology. The Notebook’s modular design provides maximum expandability without compromising portability. The high-performance CPU and enhanced IDE hard drive provides you with extra processing power for handling complex graphics and running large programs. A premium notebook designed for successful executives who demand the very best and featuring ultimate power, ultimate wide screen display, ultimate AV capabilities and ultimate connectivity. A Media solution is a combination of Windows XP software augmented by InterVideo WinCinema – including WinDVR for watching television, WinDVD for viewing movies and WinRIP for playing music. Unpacking the Notebook The Notebook comes securely packaged in a sturdy cardboard shipping carton. Upon receiving your Notebook, open the carton and carefully remove the contents. If anything is missing or damaged, please contact your Notebook dealer immediately. The shipping carton should contain the following items: • The Notebook computer • An AC adapter • An AC power cord • Software Drivers CD Do not throw the packaging materials away. You may need them later if you have to ship the computer for repairs.
10 Because the Notebook computer is available in different configurations, some of the features mentioned in this manual might not be included on your computer or may differ slightly. Getting to Know Your Computer Opening the LCD Panel To avoid damage to the display panel: 1. Try not to slam the display upon closing it. 2. Try not to place any object on top when it is closed or open. 3. Be sure the system is turned off or in suspend mode before you close the display panel. With the LCD screen open, you will see several features important for operating your Notebook computer. Each of these features is briefly described below:
11 1. LCD Screen 2. System Status Indicator Panel CardReader access Hard Disk access NumLock mode CapsLock mode ScrollLock mode 3. Wireless LAN Switch Button 4. TV Button (Launch the WinDVR application) 5. DVD Button (Launch the WinDVD application) 6. Internet Explorer Button 7. Outlook Express Button
12 8. Power/Resume Button 9. Stereo Speakers 10. Keyboard 11. The Built-in Microphone 12. TouchPad 13. TouchPad Buttons The Front Side LED Indicators 1. Power On This LED will light when the system is power on. 2. Suspend This LED will light when the system is in suspend mode. 3. Battery Charge This LED will light when the battery is in charging mode.
13 The Left Side 1. DC IN Connector 2. The CD-ROM/DVD-ROM or DVD CD-RW Combo 3. PCMCIA 4. CardReader Be sure the face of the card must be facing down when inserting it to the cardreader slot. 5. PCMCIA Eject Button 6. 1394 Port
14 The Right Side 1. Kensington Lock 2. Ventilation Opening 3. MCE Port 4. External CRT Port 5. S-Video Port 6. Modem Port Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment. To reduce the risk of fire use only No. 26 AWG or larger telecommunication line cord.
15 7. LAN Port When using a LAN, please use an EMI Shielding Cable to minimize an inteference when transmitting. 8. USB Ports 9. Audio Line Out Jack 10. ExternalMicrophone Jack The Rear 1. Cable TV Input Before connecting the cable into the connector, be sure to remove first the cover on the cable TV connector at the rear of the computer with the aid of a screw driver. One more thing that you need to be aware of is to know the video standard being used in your country that you are viewing. This system supports 3 video standard namely: NTSC, PAL and SECAM. For detailed information on the proper connection of the cable TV, please refer to Chapter 9 on “Viewing Live Video”. 2. USB Ports
16 The Bottom Panel 1. Expansion Compartment 2. Hard Disk 3. Optical Drive 4. CPU Compartment 5. Battery Release Latch
17 6. Battery Lock 7. Battery
18 Page intentionally left blank
19 GETTING STARTED Connecting to a Power Source Connecting the AC Adapter A universal AC adapter is provided to supply your computer with power and also charge the computer’s battery pack. The adapter’s AC input voltage can range anywhere from 100 to 240 volts, covering the standard voltages available in almost every country. The power cord for the AC adapter requires a three-hole grounded AC outlet. To connect the computer to an external power source: 1. Plug the AC adapter’s connector into the DC-IN connector at the left side of the computer. 2. Connect the power cord to the AC adapter and then to a wall outlet.
20 Do not use inferior extension cords as this may result in damage to your Notebook. The Notebook comes with its own AC adapter. Do not use a different adapter to power the computer and other electrical devices. Whenever possible, keep the AC adapter plugged into the Notebook and an electrical outlet to recharge the battery. Never turn off or reset your Notebook while the hard disk is in use and the HDD status icon is lit; doing so can result in loss or destruction of your data. Always wait at least 5 seconds after turning off your Notebook before turning it back on; turning the power on and off in rapid succession can damage the Notebook’s electrical circuitry. Turning On Your Notebook Computer Turn on your Notebook by pressing the power button. Hold the button down for a 1 or 2 second and release. The Power-On Self Test (POST) runs automatically. After the POST is completed, the computer reads the operating system from the hard disk drive into computer memory (this is commonly referred to as “booting” a computer). If your OS (Operating System such as Windows XP etc) is installed, it should start automatically. To turn the Notebook off, save your work and close all open applications, click on Start, then select the “Turn off the computer”. A selection box will be displayed and click on the “Turn Off” button to shut down your computer. When your computer hangs up, press the power button for 4-6 seconds to shut down the computer. Operating on Battery Power Your computer comes with a rechargeable battery pack that lets you operate the computer without an external power source. When the battery pack is fully charged, you can operate the computer for approximately 2 hours under the following conditions: • The battery pack initially has a full charge. • No peripheral devices are installed. • The disk/DVD-ROM drives run no more than 10% of the time.
21 Only use batteries that are approved by an authorized dealer for this model only. All batteries are not the same and therefore should not be treated as such. Using the wrong battery could cause serious damage to your computer and yourself through toxic emissions. Inserting and Removing the Battery Pack The battery pack should already be inserted in your Notebook computer when you unpack it. If not inserted, follow these directions:
22 To remove the battery pack: Charging the Battery Pack The installed battery pack charges automatically any time the computer is connected to the AC adapter and an external power source. If this is your first time to use the battery, be sure to fully discharge the battery and recharged until it is fully charged.
23 USING THE NOTEBOOK COMPUTER Adjusting the LCD Screen Display The LCD screen display can be adjusted by the following key combinations. KEYS FUNCTIONS [Fn] + [F7] Decreases the brightness level. [Fn] + [F8] Increases the brightness level. [Fn] + [F10] Use this key combination to expand your video screen or toggle to its original size. [Fn] + [F12] This key combination toggles the display between the LCD, CRT, simultaneous LCD/CRT, simultaneous LCD/TV, simultaneous LCD/CRT/TV. LCD Care LCD screens are delicate devices that need careful handling. Please pay attention to the following precautions: • When you are not using the computer, keep the LCD screen closed to protect it from dust. • If you need to clean your LCD screen, use a soft tissue to gently wipe the LCD surface. • Do not put your fingers or sharp objects directly on the surface and never spray cleaner directly onto the display. • Do not press on, or store any objects on the cover when it is closed. Doing so may cause the LCD to break. External CRT Display You can hook up an external monitor through the 15-pin CRT connector. • LCD only • CRT only
24 • Simultaneous display of the LCD screen and CRT monitor • Simultaneous display of the LCD screen and TV screen • Simultaneous display of the TV screen, CRT monitor and LCD screen You can switch between these display configurations by pressing the key combination [Fn] + [F12]. For information on connecting an external display, please refer to Chapter Four. A Tour of the Notebook’s Keyboard The Notebook’s keyboard uses a standard QWERTY layout with the addition of special function keys and an embedded numeric keypad for number intensive data entry. Your keyboard supports Windows by incorporating the two Windows specific keys. With the two Windows keys you will be able to access and take advantage of many of the timesaving features of Windows software. The function keys (F1-F12) on the top row of the keyboard, serve different purposes and carry out different tasks depending on the application you are running. The cursor (arrow) keys (which are all located in the lower right corner of your keyboard) and the [PgUp], [PgDn], [Home] and [End] keys (which are located along the right edge of the keyboard) allow you to move the active cursor of the computer to various locations on the screen or within the document. The embedded numeric keypad consists of 15 keys that make number intensive input more convenient. Like the [Num Lock] key, these keys are labeled in blue on the keycaps. Numeric assignments are located at the upper right of each key. When the numeric keypad is engaged, the NumLock icon will appear in the System Window. The keypad is activated by pressing the [Fn] + [NumLk] key. If an external keyboard is connected, pressing the NumLock key on either the Notebook or external keyboard will enable/disable NumLock of both keyboards in unison. To disable the Notebook numeric keypad while keeping the keypad on an external keyboard activated, use the [Fn] + [NumLk] hot key on the Notebook keyboard.
25 The Notebook’s Hot Key Controls KEYS FUNCTION(S) Power Button Press this button once to power on or enter the suspend/resume mode. Press this button for more than 4 seconds to power off the system. [Fn] + [F2] This key combination turns on/off the volume. [Fn] + [F3] Decreases the speaker volume. [Fn] + [F4] Increases the speaker volume. [Fn] + [F5] Enable/disable Touch pad [Fn] + [F7] Decreases the brightness level. [Fn] + [F8] Increases the brightness level. [Fn] + [F10] Use this key combination to expand your video screen or reset to its original size. [Fn] + [F12] This key combination toggles the display between the LCD, CRT, simultaneous LCD/CRT, simultaneous LCD/TV, simultaneous LCD/CRT/TV. Launch Button KEYS FUNCTION(S) Wireless Button Press this button to On/Off wireless function. TV Button Press this button to open the TV function. (Launch the InterVideo WinDVR application) DVD Button Press this button to open the DVD player for playing any DVD file (Launch the InterVideo WinDVD application) Internet Button Open the Microsoft’s IE Internet Explorer Email Button Open the Microsoft’s Outlook
26 The TouchPad The touchpad is a rectangular electronic panel located just below your keyboard. You can use the static-sensitive panel of the touchpad and slit it to move the cursor. You can use the buttons below the touchpad as left and right mouse buttons. TouchPad Precautions The TouchPad is a pressure sensitive device. Please take note of the following precautions. • Make sure the TouchPad does not come into contact with dirt, liquids or grease. • Do not touch the TouchPad if your fingers are dirty. • Do not rest heavy objects on the TouchPad or the TouchPad buttons. You can use the TouchPad with Microsoft Windows as well as non-Windows applications. Data Storage and Retrieval Data storage and retrieval are two of the most fundamental tasks you will perform when working with your computer. The Notebook is equipped with a hard disk drive (HDD). The HDD is removable allowing for easy upgrades. The DVD-ROM/Combo Features of the DVD-ROM/Combo Module The features of the DVD-ROM/Combo drive are listed below.
27 • The Audio Play feature allows you to play music CDs • Front panel load/unload button • Supports CD-DA, DVD-ROM mode 1 and mode 2, Multi-Session Photo CD™, CD-I/Video CD (pcs.) • Low power consumption • 12.7mm height Precautions for Handling DVD-ROM/Combo Discs • Always hold the disc by the edges, avoid touching the surface. • Use a clean, dry, cloth to remove dust, smudges, or fingerprints. Wipe from the center outward. • Do not write or place objects on the surface of the disc. • Store discs in a cool dry place not to damage the disc. • Do not use benzene, thinners, or cleaners with detergent. Only use DVD-ROM cleaning kits. • Do not bend or drop the discs. Power Saving Modes This section contains information on the Notebook’s power system, including the AC Adapter, the battery system, recharging the battery, and tips for conserving battery power. The power system is comprised of two parts, the AC Adapter and the battery system. The AC Adapter converts AC power from a wall outlet to the DC power required by the computer. The Battery Power System A fully charged pack will provide approximately 2 hours of battery life depending on your system configuration application it runs. Before using the computer on battery power for the first time, check the battery status icon on the Windows Toolbar to make sure the battery is fully charged. See Battery Status later in this section for a description and explanation of the Windows Battery icon. Charging the battery takes about 4 hours to charge when the system is in off state. If possible, always charge the battery completely. Removing the Battery Pack To remove the battery pack from its compartment, please refer to Chapter Three, Inserting and Removing the Battery Pack.
28 Preparing the Battery Pack for Use Before using the battery pack for the first time, the Smart Battery IC within the battery pack should be calibrated in order to get accurate reporting of remaining battery life status. To calibrate the battery pack follows the instructions below: 1. Insert the battery into the battery compartment and turn on the Notebook. If the battery is completely without power go to the next step. Otherwise, let the battery run down until the battery low-low warning beeps are heard. The system will automatically enter Suspend mode. 2. Turn the Notebook off. Connect the AC adapter and let the battery fully recharge. When the battery charge indicator turns off, the battery is fully charged. 3. Turn On the notebook, let the battery run down until the battery is in low-low state and you hear a warning beeps. The system will automatically enter the Suspend mode. You can now connect the AC adapter. 4. The battery pack is now calibrated properly. In general, using the battery until the low-low battery-warning indicator appears and fully recharges the battery each time (full discharge/charge cycle) will ensure the accurate reporting of the battery gauge status. Automatic Battery Pack Charging Function You can automatically charge the battery pack by using the AC Adapter. The charge time is about 4 hours when the Notebook power is turned off. The following table summarizes the charging modes: Charge Mode Charge Time Fast 4 hours with the system off or in Suspend mode. The temperature must be 25°C or below room temperature. Pre-Charge A pre-charge is supplied to the Li-Ion battery pack. Battery Status Windows XP has an applet in the Control Panel that will display an icon in the Windows taskbar indicating when the Notebook is running on battery power or is attached to the AC adapter. This applet also displays a meter that indicates how much charge is remaining in the battery.
29 Battery Low Warning When the pack initially reaches the “Battery Low” state approximately 7 ~ 10 minutes of the usable battery life is left. You will hear an audible beep signal every 1.5 seconds alerting you to the “Battery Low” status. When the battery power reaches the “Battery Low Low” status the beeping sound will accelerate. Your battery now has 1 ~ 2 minutes of battery charge remaining. You must save your data or connect AC power immediately; otherwise, you may lose your data. Sound Meaning Continuous beeping every 1.5 seconds Battery Low: Indicates that there is 7 to10 minutes charge remaining. Beeping accelerates Battery Low Low: Indicates that there is 1 to 2 minutes of battery charge remaining. Save your work and turn off the Notebook, or connect the AC adapter. When there is only one minute of battery charge remaining, the Notebook will enter suspend mode or hibernate according to Windows setting. You should connect AC power and resume to save your work. Small Battery for the Real Time Clock There is a small built-in battery pack that supplies power to the system in order to maintain certain system information while the power is off. If the Notebook is left without a power source for long period of time, this battery will be exhausted and system information will be lost. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Never remove the battery pack while the power is on as this may result in data loss when the system loses power. Battery Calibration The purpose for this process is to provide a long battery life for your system battery pack. 1. Turn on the computer, when the text appears, press [Del] or the [Delete] key until the system enters the BIOS Setup screen, you may now make the necessary changes. 2. Press the è arrow key until it reaches the “Exit” menu screen. Again press the ê arrow key and select the “Battery Calibration” item.
30 Press the [Enter] key and disconnect the AC adapter then press the [Y] key until you hear continuous battery low-low warning beeping sounds. The system will be fully discharge and shutdown completely. 3. Connect the AC adapter and let the battery fully recharge. The “Battery Charge LED” which is located at the left side of the notebook will light indicating it is in charging status. 4. When the battery charge LED turns off will indicate the system is fully charged. 5. Repeat step 1 to 4 once again. 6. The battery is now fully calibrated. Resetting the System After installing a software application package, you may be prompted to reset the system to load the changed operating environment. To reset the system, or “reboot,” press the [Ctrl] + [Alt] + [Delete] keys simultaneously. This is known as “warm boot.” This key combination acts as “software” reset switch when you encounter hardware or software problems, which lock up the Notebook. If this key combination does not shut down the Notebook, you can reset the Notebook by using the Notebook’s power button. Should the Notebook lock up for some reason, pressing this button powers the Notebook off. Adjusting the Brightness To adjust the brightness on the LCD screen, press and hold down the [Fn] key in the lower left hand corner of the keyboard and press the [F7] key to reduce the brightness or [F8] to increase the brightness.
31 DESKTOP OPERATION This chapter discusses those functions of your notebook that are typical of desktop systems. Audio The Multimedia Sound System The Notebook’s built-in audio capabilities allow you to take advantage of a wide range of education and entertainment multimedia software. The Notebook is equipped with internal stereo speakers, a microphone, and input audio ports for external audio units. An external microphone can be connected to the microphone jack. External speakers or headphones can be connected to the Notebook’s audio-out jack. External audio devices can be connected to the Line in jack. Audio Volume Control The Notebook is equipped with hot-key volume controls: Pressing the [Fn] + [F3] hot-key combination decreases the audio output volume; press the [Fn] + [F4] hot-key combination increases the audio output volume. Audio Software Your notebook comes equipped with an integrated sound system capable of providing you with quality audio sound through the built-in speakers or through external speakers connected via the system ports. Sound Recording Your system allows you to record sounds and store them as files using the microphone via the microphone jack on the rear of the notebook computer. Check the Windows Help and Support Center in Windows for information on using the various elements in sound recording.
32 For a high-quality sound, click on the "Volume Control" at the lower right end of your screen. From the Volume Control windows, click on the "Advanced" tab, click and select the "Microphone Boost" item. Playing Sound Files Your notebook can play audio files stored in MIDI, WAVE or MP3 file format. Check the Help and Support Center in Windows for information on the functions of the Media Player. External Speakers and Microphone The sound system is capable in providing high-quality sound to external speakers and receiving and processing sounds from an external microphone or external sound source. Connecting Peripheral Devices To expand your computing capabilities, you can add a variety of external devices to your computer.
33
34 Page intentionally left blank
35 INTERNET CONNECTION There are numerous ways to connect to the Internet. This may vary from the user’s working environment as well as system specifications. • Using a modem and a telephone line • Using a wired LAN • Using a wireless LAN (Optional) Using a modem for Connection to Internet • Use a telephone line to connect to the modem port of your computer. Do not use a digital telephone line. • Please apply to an Internet Service Provider (ISP) for Internet service in order for you to connect the modem to the Internet and use e-mail. For more detail on the Network key, please refer to your local ISP provider and follow the procedures describe in the “ISP Installation Guide” to proceed with the installation. Using a wired LAN for Connection to Internet For you connect to the Internet, a wired LAN environment normally uses the company’s LAN or a broadband modem. 1. Use the network (LAN) cable to connect to the LAN port of the system. 2. Select on “My Network Places” and click on the “View Network Connection” in the “Control Panel” window. 3. In the “Network Tasks” window, use your mouse pointer to click on
36 the “Local Area Connection”. 4. Select “Properties” from the popup menu that appears 5. In the “This connection uses the following items” field, select “Internet Protocol (TCP/IP), and click “Properties”. 6. Enter the system’s IP and DNS server addresses on the General tab of the “Internet Protocol (TCP/IP) Properties” window. If DHCP is used, click “Obtain an IP address automatically” and “Obtain DNS server address automatically” on the General tab. 7. After all the all the information are correctly entered in the “Internet Protocol (TCP/IP) Properties” window, click “OK” to finish. Using Both DHCP and Static IP for Connection to Internet When you are alternatively using networks with either DHCP or static IP addressing, you can use alternative settings that enable simultaneous configurations of DHCP and static IP to use both of the network connects
37 without reconfiguring. 1. Follow the steps mentioned when you are using wired LAN connection from 1 to 7. 2. Click on the “User configured” and enter the appropriate values in the “Alternate Configuration” tab. 3. When you have completed the entire configuration, click “OK”.
38 Using Wireless LAN Network for Connection to Internet (Microsoft’s Service Pack 2) (Optional)
39 CONFIGURING AND MAINTAINING YOUR SYSTEM Introduction The BIOS (Basic Input and Output System) Setup program is a menu driven utility that enables you to make changes to the system configuration and tailor your system to reflect installed hardware or alter system performance. When the Notebook is turned back on, the system is configured with the values stored in CMOS. With easy-to-use menus, you can configure such items as: • Hard drives and peripherals • Boot up Drive Sequence • Password protection • Power Management Features The settings made in the BIOS Setup program intimately affect how the Notebook performs. Navigating through BIOS Setup The Setup program has been designed to make it as easy to use as possible. If you accidentally make a setting and don’t know which one to switch back to, the Setup program has a hot key that allows you to return to the previous value. Accessing the BIOS Setup Program To access the BIOS Setup program, press the DEL key after the Notebook has run through its POST. Item Specific Help On the right side of the Setup screen is an area labeled Item Specific Help. This area will list navigation key shortcuts and information that is specific for the item that you are currently editing.
40 The Menu Bar The top of the screen has a menu bar with the following selections: • Main - Use this menu to make changes to the basic system configuration. • Advanced - Use this menu to enable and make changes to the advanced features available on your system. • Security - Use this menu to set a password. The password allows boot up and controls access to the BIOS setup menu. • Boot - Use this menu to configure the default system device used to locate and load the Operating System and for booting up the Notebook. • Exit - Use this menu to exit the current menu or specify how to exit the Setup program. To access the menu bar items, press the right or left arrow key on the keyboard until the desired item is highlighted. The Legend Bar At the bottom of the Setup screen you will notice a legend bar. The keys in the legend bar allow you to navigate through the various setup menus. The following table lists the keys found in the legend bar with their corresponding alternates and functions. Legend Key Alternate Key Function F1 Displays the General Help window. It can be enabled from anywhere in the BIOS. Esc Jumps to the Exit menu or returns to the Main menu from a submenu. ← Selects the menu item to the left. → Selects the menu item to the right. ↑ or ↓ arrow keys Moves the cursor up and down between fields. Tab Enter Moves the cursor to the next position available in the field. Shift + Tab Moves the cursor to previous position available in the field.
41 Legend Key Alternate Key Function Minus key (-) Scrolls backward through the values for the highlighted field. Plus key (+) Scrolls forward through the values for the highlighted field. Home PgUp Moves the cursor to the field at the top of the window. End PgDn Moves the cursor to the field at the bottom of the window. F9 Sets the parameters for the current menu to their default values. F10 Save and Exit. Enter Will select a sub menu or show a range of options for a field. Launching Submenus Note that a right pointer symbol  appears to the left of certain fields. This pointer indicates that a submenu can be launched from this field. A submenu contains additional options for a field parameter. To call up a submenu, simply move the cursor to highlight the field and press the [Enter] key. Use the [Esc] key to return to the Main menu. General Help In addition to the Item Specific Help window, the BIOS Setup program also provides a General Help screen can be called up from any menu by simply pressing [F1]. To exit the help window, press the [Enter] or the [Esc] key. Save Changes and Exit the Setup Program Refer to the Exit menu section of this chapter for detailed information on saving changes and exiting the setup program.
42 The Main Menu When the Setup program is accessed, the following screen appears:
43 The Advanced Menu Selecting Advanced from the menu bar displays the advanced menu: If your system support InterVideo application, select the “InterVideo” item from the “Shortcut Key Working With” selection menu. If your system supports the WinXP MCE application, select the “WinXP MCE” item from the “Shortcut Key Working With” selection menu. If your system supports the CyberLink application, select the “CyberLink” item from the “Shortcut Key Working With” selection menu. (Optional)
44 The Security Menu The Notebook’s advanced system of security allows you to set a password to prevent unauthorized access to system resources, data, and the BIOS Setup Program.
45 The Boot Menu The Boot menu allows the user to specify the order in which the Notebook is to check for a device to boot the system. You can also configure the way that the system will boot up. To make changes, select Boot from the menu bar. The following screen appears: Use the up and down arrows to select the boot device. Then press either the plus key [+] to move the device up the list or the minus key [-] to move the device down the list.
46 The Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup. Select Exit from the menu bar to display the following menu:
47 MICROSOFT CENTER EDITION (MCE) (OPTION) Windows XP Media Center Edition (MCE) The Windows MCE is a complete software for home PC operating system for you to enjoy entertainment choices together in one place easily accessible from anywhere in the room. This will benefits the consumers to enjoy Media Center experience in their own living room. For more information on the function of the MCE, please refer to the Microsoft’s Windows XP MCE user’s guide that goes along with your software package.
48 Please be advice that when you received your computer, the MCE port at the right side. MCE Application Sound Adjustment This notice only applies to those systems that only support MCE application when you are using the Windows volume adjustment function. From your Windows, click on the lower left corner of the screen the speaker icon and open the Volume Control Properties Window. If you are using MCE’s “My TV” application 1. Use your mouse right button to click on the “Volume” icon and select the “Open Volume Control” item. 2. The “Volume Control” display window is displayed on your screen. 3. Click on the “Options” tab and select the “Properties” item.
49 4. From the “Properties” display window, enable the “Aux” item and click “OK”. 5. The “Aux” is now added on the “Volume Control” window. 6. Enable the “Mute” tab on the “Aux” item and close the window. If you are using InterVideo’s WinDVR application The procedures are almost the same as those mentioned above from steps 1 to 5 to adjust the volume control. On step 6, disable the “Mute” tab on the “Aux” item and close the window.
50 Page intentionally left blank

Navigation menu