Enlighted SU4E Compact Sensor User Manual PowerPoint Presentation

Download:
Mirror Download [FCC.gov]
Document ID	3002465
Application ID	z0p62yeuaMZMx9Gr8fxu6A==
Document Description	User Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	26.49kB (331103 bits)
Date Submitted	2016-05-24 00:00:00
Date Available	2016-09-21 00:00:00
Creation Date	2016-03-28 11:45:52
Producing Software	Microsoft® PowerPoint® 2013
Document Lastmod	2016-03-28 11:45:52
Document Title	PowerPoint Presentation
Document Creator	Microsoft® PowerPoint® 2013
Document Author:	Enlighted

FCC and Industry Canada Compliance Information
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions:
• this device may not cause harmful interference, AND
• this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by Enlighted Inc.
could void the user's authority to operate the equipment.
Technical Support
For questions regarding the installation or operation of this
product, contact Enlighted
Technical Support: support@enlightedinc.com
6-wire Compact Sensor
(SU-4E)
Installation Instructions
Company Contact Information
Location: 930 Benecia Ave, Sunnyvale, CA 94085
Phone: +1.650.964.1094
Web: enlightedinc.com
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes:
• l'appareil ne doit pas produire de brouillage, ET
• l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Figure 1: Compact Sensor
CE
This device complies with the essential requirements and other relevant
requirements of the R&TTE Directive (1999/5/EC). The equipment is Class 1
radio equipment which can be placed on the market and be put into
service without restrictions in accordance with article 1(3) of Commission
Decision 2000/299/EC (Version July 2014).
Shipped Components
• Enlighted Compact Sensor Unit
Model: SU-4E
No: SU-4E-01
FCC ID: AQQ-SU4E01
IC: 10138A-SU4E01
Tools you may Need
• 1” Drill bit
• Hand drill
Copyright © 2016 Enlighted Inc. All rights reserved.
All other brand or product names are trademarks of
their respective companies or organizations.
Page 5
Page 6
94-00552-02 Rev07
Page 1
Caution
qualified electrician in accordance with local, state, and
national electrical codes (NEC) and requirements.
Tile Mount Sensor Installation
Step
LED Description
Fixture Mount Sensor Installation
• Installation and maintenance must be performed by a
Description
Step
Description
Switch off the circuit breaker supplying power to the light.
LED not on
Check power and wiring
2.
Mount the Control Unit in the ballast cavity of the fixture or
in a UL approved enclosure.
Purple solid
All LEDs are on during boot time for 5-6
seconds
Green blinking
Sensor commissioned and working
Red blinking
Incompatibility between LED driver and sensor
– Replace LED driver and if not resolved,
replace sensor.
Red solid
Faulty sensor – replace sensor
Green solid
Sensor installed, initialized, and
uncommissioned – waiting for discovery.
Blue solid
Image being upgraded or BLE Reset
Switch off the circuit breaker supplying power to the light.
3.
2.
Mount the Control Unit (CU) behind the ceiling tile or in a UL
approved enclosure. Refer to the Control Unit Installation
Guide.
Connect the RJ-12 connector end of the Compact Sensor
cable to the Control Unit. See Figure 5.
4.
3.
Connect the RJ-12 connector end of the Compact Sensor
cable to the Control Unit. See Figure 5.
Note: The sensor is designed to mount in a ½ inch trade size
knockout on a fixture.
Determine the location for the sensor in the fixture and cut
a ½ inch knockout in the fixture. See Figure 3.
4.
Note: The sensor is designed to mount in a
in the ceiling tile.
Make a small circular cut in the ceiling tile.
inch hole
5.
Unthread the spring arms from the Compact Sensor.
6.
Insert the Compact Sensor through the hole in the fixture.
Use the spring arms from behind the sensor to fasten the
Compact Sensor. See Figure 4.
5.
Pull the 6-pin end of the Compact Sensor cable through the
hole in the tile. See Figure 2.
7.
6.
Insert the end of the wire into the sensor’s 6-pin connector.
See Figure 2.
Insert the 6-pin end of the Compact Sensor cable to the
6-pin connector on the sensor.
8.
Turn the power on by switching on the circuit breaker.
7.
Push the spring arms together and insert the sensor through
the hole in the tile. See Figure 2.
8.
Turn the power on by switching on the circuit breaker.
Spring
arms
Description/Solution
1.
1.
15/16th
LED Status
Push the spring
arms together
and insert the
sensor
Figure 5: Wiring Connection
Figure 2: Tile Mount Sensor
Page 2
Figure 3: Sensor location
in a fixture
Figure 4: Fixture Mount Sensor
Page 3
Page 4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
Language                        : en-US
Tagged PDF                      : Yes
Title                           : PowerPoint Presentation
Author                          : Enlighted
Create Date                     : 2016:03:28 11:45:52-07:00
Modify Date                     : 2016:03:28 11:45:52-07:00
Producer                        : Microsoft® PowerPoint® 2013
Creator                         : Microsoft® PowerPoint® 2013

EXIF Metadata provided by EXIF.tools