Enlighted SU5S SU5S User Manual PowerPoint Presentation

Enlighted, Inc. SU5S PowerPoint Presentation

User Manual

Page 5 Page 6 Page 1Copyright © 2017 Enlighted Inc. All rights reserved.All other brand or product names are trademarks oftheir respective companies or organizations.TechnicalSupportFor questions regardingtheinstallation or operation ofthis product,contact EnlightedTechnicalSupport: support@enlightedinc.comCompany Contact InformationLocation: 930 Benecia Ave, Sunnyvale, CA 94085Phone: +1.650.964.1094 Web: enlightedinc.comFCC and Industry Canada Compliance InformationThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.This device complieswith Part 15 of the FCC Rules and Industry Canadalicense-exempt RSS standard(s). Operation is subjectto thefollowing two conditions:•this devicemay not cause harmful interference, AND•this device must accept anyinterference received, includinginterference that may cause undesiredoperation.Changes or modifications not expressly approved by Enlighted Inc.could void the user'sauthority to operate the equipment.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.L'exploitationest autoriséeauxdeux conditions suivantes:•l'appareil ne doit pas produire de brouillage,ET•l'utilisateur de l'appareildoitaccepter tout brouillageradioélectriquesubi,même si le brouillage est susceptible d'encompromettre le fonctionnement.CEThis device complies with the essential requirements and other relevant requirements of the R&TTE Directive (1999/5/EC). The equipment is Class 1 radio equipment which can be placed on the market and be put into service without restrictions in accordance with article 1(3) of Commission Decision 2000/299/EC (Version July 2014).Smart Sensor (Front and Rear)Smart Sensor(SU-5S)Installation InstructionsShipped Components•Smart Sensor•Anchor ScrewSupplemental Components•Enlighted Sensor Cable: CBL-2-7F•Enlighted Control Unit93-02058-01 Rev01Models: SU-5S-H: High Bay, Smart SensorSU-5S-L: Standard Bay, Smart SensorFCC ID: AQQ-SU5S IC: 10138A-SU5SPreliminary
Page 2 Page 3 Page 4InstallationCautionInstallation and maintenance must be performed by a qualifiedelectrician in accordance with local, state, and nationalelectrical codes (NEC) and requirements.LED DescriptionStep 1: De-energize the luminaire.Step 2:Determine the location of the sensor. Push and rotate the anchor screw to the tile at that location. Step 3:Select a place near the anchor screw for the RJ12 connector of the sensor cable from the Control Unit (CU) to exit. See Wiring Diagram on Page 4. Make a small cut in the ceiling tile for the cable to exit. Step 4:Connect the RJ12 connector to the sensor bottom.Step 5:Slide the Smart Sensor onto the screw head. Step 6:Slip the excess sensor cable up into the plenum area and adjust the ceiling tile to the original position. Step 7: Energize the luminaire and confirm that the green LED is solid.Anchor Screw Sensor CableThe Smart Sensor (SU-5S) should be mounted to the ceiling tile within a few inches (between 13/4” to 3”) of the lighting fixture. For wiring connections from the Control Unit to the sensor, refer to the Control Unit Installation Guide. Wiring Diagram:LED Status Description/SolutionLED not on Check power and wiringGreen blinking Sensor commissioned and workingRed blinking Sensor not commissionedRed solid Faulty sensor –replace sensorGreen solid Sensor installed, initialized, and uncommissioned –waiting for discovery.Blue solid Sensor received a request to identify itself Preliminary

Navigation menu