Eton FR-1000 FRS/GMRS COMBINATION User Manual FR1000 Manual qxp
Eton Corporation FRS/GMRS COMBINATION FR1000 Manual qxp
Eton >
USERS MANUAL
Model FR-1000Series
Page 3
TABLE OF CONTENTS 3
Introduction 4
Important Notice, FCC Licensing 5
LCD Display 6
Controls 7
Battery Installation 8
Charging the Battery Pack 9
Low Battery Level Indicator 9
Selecting the Power Source 9
Operating Your Radio 10 - 17
External Speaker/Microphone Jack 17
USB Jack 17
Troubleshooting Guide 18
Use and Care 18
Specifications and Frequency Charts 19 - 20
Model FR-1000Series
Page 4
Welcome to the world of Eton electronics
Congratulations on your purchase of a high quality ETON product. Your 2-
way radio represents the state-of-the-art in high-tech engineering. Designed
for GMRS (General Mobile Radio Service) operation, this compact package
is big in performance. It is a quality piece of electronic equipment, skillfully
constructed with the finest components. The circuitry is all solid-state and
mounted on a rugged printed circuit board. Your two-way radio is designed
for reliable and trouble-free performance for years to come.
Features
- 22 GMRS/FRS Channel
- 121 Privacy Codes (38 CTCSS / 83 DCS)
- AM/FM Receiver
- VOX
- Selectable Call Alert
- NOAA Weather Radio
- NOAA Weather Alert
- Scan Function
- MONITOR Function
- Dual Watch Function
- Roger Beep Tone
- Silent Operation
- Keypad Lock
- Power HI/LO Settings
- Flashlight
- Clock/Alarm Clock Function
- Dynamo Crank Battery Charge Capability
- Phone Charger Jack (For Mobile Phone Charging)
- Speaker / Microphone Jacks
- Battery Meter / Battery Low Indicator
- SOS Function
- Siren Function
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions : (1) this device does not cause harmful interference, and (2) this radio must
accept any interference that may cause undesired operation.
To maintain compliance with FCC’s RF exposure guidelines, for body-worn operation, this
radio has been tested and meets the FCC RF exposure guidelines when used with Eton
Radio Corp. accessories supplied or designated for this product. Use of other accessories
may not ensure compliance with FCC RF exposure guidelines. (Tested with Headset
Model: AVP-1)
Model FR-1000Series
Page 5
IMPORTANT NOTICE, FCC LICENSE REQUIRED FOR GMRS OPERATION
The FR-1000Series operates on GMRS (General Mobile Radio Service)
frequencies which require an FCC (Federal Communications Commission)
license. You must be licensed prior to operating on channels 1 - 7 or 15 - 22,
which comprise the GMRS channels of the FR-1000Series. Serious penalties
could result for unlicensed use of GMRS channels, in violation of FCC rules,
as stipulated in the Communications Act's Sections 501 and 502 (amended).
You will be issued a call sign by the FCC which should be used for station
identification when operating the radio on GMRS channels. You should also
cooperate by engaging in permissible transmissions only, avoiding channel
interference with other GMRS users, and being prudent with the length of their
transmission time.
To obtain a license or ask questions about the license application, contact the
FCC at 1-888-CALL FCC or go to the FCC's website:
http://www.fcc.gov and request form 605.
Exposure To Radio Frequency Energy
Your Eton radio is designed to comply with the following national and
international standards and guidelines regarding exposure of human being to
radio frequency electromagnetic energy:
- United States Federal Communications Commission, Code of Federal
Regulations: 47 CFR part 2 sub-part J
- American National Standards Institute (ANSI)/Institute of Electrical &
Electronic Engineers (IEEE) C95. 1-1992
- Institute of Electrical and Electronic Engineer (IEEE) C95. 1-1999 Edition
- National Council on Radiation Protection and Measurements (NCRP) of the
United States, Report 86, 1986
- International Commission on Non-lonizing Radiation Protection (ICNIRP)
1998
To control your exposure and ensure compliance with the general population
or uncontrolled environment exposure limits, transmit no more than 50% of
the time. The radio generates measurable RF energy exposure only when
transmitting.
IMPORTANT: Changes or modifications to this unit not expressly approved by
ETON could void your right to operate this unit. Your radio is set up to transmit
a regulated signal on an assigned frequency. It is against the law to alter or adjust
the settings inside the COMMUNICATOR to exceed those limitations. Any
adjustment to your radio must be made by qualified technicians.
Model FR--1000Series
Page 6
LCD DISPLA
Y
2
1
3
4
5
6
7
8
9
13
14
15
16
17
18
19
20
21
13. TRANSMIT POWER LEVEL ICON –Indicates
TX Power setting (HI/LO)
14. PRIVACY CODE ICON – Indicates Privacy
Code setting (CTCSS/DCS).
15. KEY LOCK ICON – Indicates KEY LOCK
mode is on.
16. SCAN ICON – Indicates when the radio is in
Scan mode.
17. NOAA WEATHER (WX) BAND ICON –
Indicates when the radio is in Weather
Band mode.
18. ALERT ICON – Indicates the radio has
received a NOAA WEATHER (WX) ALERT
signal.
19. EMG ICON – Indicates when the radio
EMERGENCY fucntion is on.
20. BATTERY METER – Indicates the battery
level.
21. ROGER BEEP ICON – Indicates radio’s
Roger Beep Tone is on.
22. ALARM CLOCK ICON – Indicates when the
Alarm Clock is on.
23. ROGER BEEP ICON – Indicates radio’s
Roger Beep Tone is on.
24. VOX ICON – Indicates when VOX mode is
active.
10
11
12
22
24
23
1. RECEIVER (RX) / TRANSMIT (TX) ICON –
Indicates radio is transmitting a signal (TX) or if
the radio is receiving a transmission (RX).
2. CHANNEL NUMBER – Changes from 1~22 on
GMRS/FRS band (1~7 on WX band). This is
also used to indicate in part the current AM/FM
receiver frequency setting and the current
clock setting.
3. CLOCK AM/PM ICON – Indicates the clock is
set in AM or PM.
4. NOAA WEATHER (WX) ALERT ICON –
Indicates the WX Alert function in on.
5. AM RECEIVER ICON – Indicates radio is in AM
receiver mode.
6. FM RECEIVER ICON – Indicates radio is in FM
receiver mode.
7. NOAA WEATHER (WX) BAND ICON –
Indicates when the radio is in Weather
Band mode.
8. GMRS ICON – Indicates radio is in GMRS mode.
9. FLASHLIGHT ICON – Indicates the Flashlight in
on.
10. S.O.S. ICON – Indicates the SOS function is
on.
11. SIREN. ICON – Indicates the Siren function is
on.
12. DUAL WATCH ICON – Indicates the Dual
Watch function is on.
Model FR-1000Series
Page 7
CONTROLS
25
26
27
28
29
30
31
32
33
34
35
25. ANTENNA
26. BAND SWITCH – used to switch between
AM/FM/WX/GMRS mode.
27. FLASHLIGHT – Built-in flashlight.
28. FUNCTION SWITCH – used to switch
between WX Alert/OFF/Flashlight/SOS/Siren
function.
29. SPEAKER – Built-in speaker.
30. BATTERY SOURCE SWITCH – used to
switch the radio OFF or switch between
Alkaline and Rechargeable NiMH batteries.
31. TUNING KNOB – Rotate clockwise/counter-
clockwise to make adjustment in the MENU
mode. It can also make adjusment in the
Clock and AM/FM receiver mode.
32. MIC – Built-in microphone.
33. DYNAMO CRANK HANDLE – Rotate clock-
wise or counter-clockwise to charge the NiMH
battery pack.
34. DYNAMO CRANK HANDLE SHAFT
35. POWER/VOLUME KNOB – Turn clockwise to
increase the volume level. Turn counter-clock-
wise to decrease the volume level and turn
the power off.
36
37
38
39
40
36. SCAN/HOUR Button – Press to set the Scan
mode on/off in GMRS mode. Press to change
the Hour setting in Clock mode.
37. MENU/MINUTE Button – Press to access
Menu mode in GMRS/FRS and WX mode.
Press to change the Minute setting in Clock
mode.
38. MONITOR / ALARM ON/OFF Button – Press
to turn on the Monitor function in GMRS
mode. Press and hold to turn alarm on/off
in Clock mode. .
39. LOCK/CALL / HOUR Button – Press and
hold to set the key pad lock on/off in GMRS
mode. Press to send a CALL Alert signal in
GMRS mode. Press to change the Hour
setting in Clock mode.
40. PTT/SNOOZE Button – Press and hold to
transmit voice communication in GMRS mode.
Press to confirm the selection in MENU and
Clock mode. Press to activate SNOOZE
function in Clock mode.
Model FR-1000Series
Page 8
BATTERY INSTALLATION
Your FR-1000Series radio operates with either 4 AA alkaline batteries or an
optional NiMH battery pack.
To install the batteries:
1. With the back of the radio facing you, remove the Battery Cover by pressing
down the Battery Cover Lock Tab until it unlocks and lifting it out from the
radio.
2. Insert 4 AA batteries observing the polarity as shown. Installing the batteries
incorrectly will prevent the unit from operating or may damage the unit. Also
install the NiMH battery pack as shown below.
3. Return the Battery Cover by pushing it down into the back of the radio until
the Battery Cover Lock Tab locks into place.
Model FR-1000Series
Page 9
CHARGING THE BATTERY PACK
Your FR-1000Series is equipped for using an rechargeable NiMH battery
pack which can be recharged using an AC wall adapter (included) or a DC
adapter (included). Initial charge time is 24 hours with a charge time of 12
hours thereafter. For maximum battery life, we recommend charging the
battery pack when the low battery icon comes on. Remove the radios from
the charger when the charge time expires. For the location of the
CHARGING JACK see page 17.
In order to ensure that the battery pack is fully charged, it is
recommended that the battery pack be charged for at least 12
hours with the radio turned OFF.
You can also charge the rechargeable NiMH battery pack using the
Dynamo Crank.
To charge using the Dynamo Crank rotate rapidly the Dynamo Crank
handle clockwise or counter-clockwise.
To get the best charging condition, it is recommended to charge the
battery pack thru the Dynamo Crank with the radio turned OFF.
1. Only use our NiMH battery pack.
2. Do not attempt to charge alkaline batteries or any batteries
or battery packs other than the one indicated in the manual.
This may cause leakage and damage to the radio.
3. For long term storage of the radio, turn the radio OFF and
remove the batteries from the radio.
BATTERY LEVEL INDICATOR
Your FR-1000Series has a BATTERY LEVEL METER that shows the
battery power level. The greater the number of bars visible, the stronger the
battery level. When the battery level is low, the Battery Shell icon
will flash in the display indicating your batteries should be replaced or
recharged if using a rechargeable battery pack.
SELECTING
THE POWER SOURCE
Your FR-1000Series can use either an Alkaline battery or the rechargeable
NiMH battery pack. Just set the BATTERY SOURCE switch to either
“Alkaline” or “Rechargeable” (for NiMH battery pack) mode.
!
Model FR-1000Series
Page 10
SETTING THE RADIO TO GMRS/FRS MODE
To set the FR-1000 to GMRS/FRS mode, move the BAND switch in GMRS
position. The LCD will show the current GMRS/FRS channel setting. The
GMRS ICON will appear on the display.
POWER ON/OFF AND VOLUME
Turn the BATTERY SOURCE switch and choose between Alkaline
batteries or NiMH Battery Pack to turn the radio on. Rotate the VOLUME
knob clockwise to increase the volume level. Rotate the control counter-
clockwise to reduce the volume level. During Power On, the LCD will
display all icons for 1 second and the LCD display will indicate the last
channel/frequency selected.
TRANSMITTING AND RECEIVING A CALL
To communicate, all radios in your group must be set to the same channel
and Privacy Code.
1. Press and hold the PTT button and speak in a normal voice into the
microphone. The TX icon will appear continuously on the LCD
Display while transmitting.
When using a HAND MIC, press and hold the PTT button on the side
of the HAND MIC and speak in a normal voice.
For maximum clarity, hold the HAND MIC 2 to 3 inches from your
mouth.
2. To receive a call, release the PTT button. The RX icon will appear on
the display when your radio is receiving a transmission.
ABOUT RANGE
Your FR-1000 Series radios are designed to give you maximum range
under optimum conditions.
Optimum Conditions are:
lOver water
lOpen rural areas without obstructions
lFlat areas where you can see the other person
To ensure you get maximum range:
lBe sure to use fresh or fully charged batteries - low batteries will
cause low power conditions
lBe sure you are on a GMRS channel - FRS channels are
restricted by the FCC to low power
lBe sure to set your radio to use Hi power.
lBe sure to point the ANTENNA upward.
OPERATING YOUR RADIO
Model FR-1000Series
Page 11
FR1000QUICK REFERENCE CHART
CHANNEL SELECTION (GMRS/FRS BAND)
Turn the TUNING knob clockwise or counter-clockwise to select one of the
22 GMRS/FRS channels.
MONITOR
Pressing the MONITOR button will let you check activity on your current
channel before transmitting. This could also be used to adjust the volume
level of the radio when it is not receiving a signal.
Press the MONITOR button again to get out of MONITOR mode.
SCAN
Your FR-1000 Series can scan all 22 channels for any activity. To enter,
quickly press the SCAN button. Repeat the same procedure to exit. Your
radio will rapidly scan each of the 22 channels and stop on any active
channel. Your radio will stay on the active channel as long as the signal is
present and will resume scanning 5 seconds after the signal is no longer
present.
When you press the PTT button to transmit on an active channel, the
scanning function will stop and remain on the active channel.
To resume scanning, quickly press the button.
CALL ALERT
Your FR-1000 Series can transmit a call alert for a fixed length of time. To
send a call alert, press the CALL/LOCK button. The TX icon will appear
while transmitting a call alert and a tone can be heard on the speaker for
confirmation.
The FR1000 has 5 call alert selections.
MENU
Channel VOX
1~22
Privacy Roger Beep
On/Off
Power
H/L
Call Alert
oF/1~5
WX Channel
1~10
Silent Operation
On/Off
oF/1/2/3
CTCSS
DCS
oF~38
oF~83
Dual Watch
1~22
WX Alert
On/Off
Privacy
CTCSS
DCS
oF~38
oF~83
Only when Dual Watch is ON
Hour Setting
12hr AM/PM
Minute Setting
0~60
Alarm Setting
0~60
Minute Setting
0~60
Clock/Alarm Clock Function
Model FR-1000Series
Page 12
KEYPAD LOCK
To avoid accidentally changing the radio setting, press and hold the
CALL/LOCK button for about 4 seconds. The KEY LOCK icon will appear
on the display. The PTT, CALL, and MONITOR function will still be active.
Repeat the same procedure to unlock the keypad.
DISPLA
Y ILLUMINATION
During Power on, the display illumination will activate for approx. 5
seconds. The display illumination can also be activated when the MENU,
SCAN button is pressed. It can also be activated if the TUNING knob is
turned.
Note: In Clock Mode (Power Off) the display illumination can be
activated by pressing any button, or when the TUNING knob is
turned.
SETTING PRIVACY CODES
Your FR-1000 Series has 121 Privacy Codes available. The selected
Privacy Code may be different for each channel. To select a Privacy
Code for the current channel press the MENU button once, and then turn
the TUNING knob to select one of the 38 CTCSS Privacy Code. Press
again the MENU button and turn the TUNING knob to select one of the 83
DCS Privacy Code. The Privacy Code icon on the display will indicate
whether you set your Privacy Code in CTCSS or DCS mode. To confirm the
selection, press the PTT button or press MENU button again to move to the
next feature setting.
Note : If you select any CTCSS Privacy Code, any pre-selected DCS
Privacy Code will be cancelled and vice-versa. Selecting a Privacy
Code of "oF" will disable the Privacy feature. To communicate
between two FR1000Series radios, all radios in your group must
be set to the same channel and Privacy Code selections.
TRANSMIT (TX) POWER LEVEL SELECTION
Your FR-1000 Series has 2 power level settings. To select the power level
on channels 1~7 and 15~22, press the MENU button until a “Pr” icon will
appear on the display. Then turn the TUNING knob to select TRANSMIT
POWER LEVEL icon (H: Hi/L: Lo). To confirm, press the PTT button or
press MENU button again to move to the next feature setting.
When the Battery Meter drops to 1 bar , the TX Power will auto-
matically switch from Hi(H) to Lo(L) level.
Note : You cannot adjust the power setting on the FRS channels
(8~14). They are set to Low power per FCC regulations.
!
!
Model FR-1000Series
Page 13
VOX (Hands-free Transmission)
Your radio has 3 VOX level settings: (oF/1/2/3).
To set VOX, press the MENU button until the display shows “Vo” while on
the right, an “oF” icon appears. Select “1”, “2”, or “3” by turning the
TUNING knob and push the PTT key, or press MENU button again to move
to the next feature setting.
VOX will be more sensitive on the “1”setting than on the “3”setting.
To turn VOX off, press the MENU button until the display shows “Vo” while
on the right, a “1”, “2” or “3” icon appears. Select “oF” by turning the
TUNING knob and push the PTT key, or press MENU button again to move
to the next feature setting.
Note: For VOX Hands-free operation use Eton headset accessories
or built-in internal microphone. The accessory hand mic is not
intended for VOX mode use.
CALL ALERT SELECTION
Your FR-1000 Series has 5 selectable CALL ALERTS (oF/1~5).
To select, press the MENU button until a “CA” icon appears and to the right
of the “CA” icon the current CALL ALERT setting is displayed. Then turn
the TUNING knob to make the CALL ALERT selections - the radio will emit
a corresponding tone for each selection. To confirm, press the PTT button
or press MENU button to move to the next feature setting.
Note: Setting the CALL Alert to “oF” will disable the CALL Alert
function.
ROGER BEEP (end of transmission) TONE
When the PTT button is released, the radio will beep to confirm to other
users that your transmission has finished.
To turn the ROGER BEEP tone on, press the MENU button until the
display shows an “rb” icon while on the right of the “rb” display, an “oF”
icon appears. Select “on” by turning the TUNING knob and push the PTT
key, or press MENU button to move to the next feature setting. The
ROGER BEEP icon will appear on the display.
To turn the ROGER BEEP tone off, press the MENU button until the
display shows an “rb” icon while on the right of the “rb” display, an “on”
icon appears. Select “oF” by turning the TUNING knob and push the PTT
key, or press MENU button to move to the next feature setting. The
ROGER BEEP icon will disappear on the display.
Model FR-1000Series
Page 14
SILENT OPERATION
Your FR-1000 Series has a SILENT OPERATION mode. In this mode, all
“beeps” and “tones” are disabled.
To turn the SILENT OPERATION mode on, press the MENU button until
the display shows an “bP” icon while on the right of the “bP” display, an
“on” icon appears. Select “oF” by turning the TUNING knob and push the
PTT key to confirm or press the MENU button to move to the next feature
setting. The KEY TONE icon will appear on the display.
To turn the SILENT OPERATION mode off, press the MENU button until
the display shows an “bP” icon while on the right of the “bP” display, an
“oF” icon appears. Select “on” by turning the TUNING knob and push the
PTT key or MENU button. The KEY TONE icon will disappear on the
display.
DUAL WATCH
Your FR-1000 Series has a DUAL WATCH function, to enable user to
monitor 2 selected channel/privacy code for any activity. It is similar with
the SCAN function but will only monitor 2 channels instead of the whole 22
channels. The first channel/privacy code is the current setting, the second
channel/privacy code is the one you will set on the MENU.
To turn on the DUAL WATCH function, press the MENU button until the
DUAL WATCH icon appear while in the right an “oF” icon appears. Select
the second channel by turning the TUNING knob.To select a Privacy Code
for the second channel press the MENU button once, and then turn the
TUNING knob to select one of the 38 CTCSS Privacy Code or press again
the MENU button and turn the TUNING knob to select one of the 83 DCS
Privacy Code. Press the MENU or PTT button to confirm. The DUAL
WATCH icon will remain on the display.
The radio will rapidly scan the two channels selected and stop on any
active channel. Your radio will stay on the active channel as long as the
signal is present and will resume scanning 5 seconds after the signal is no
longer present.
To turn off the DUAL WATCH function, press the SCAN button. The current
GMRS/FRS radio setting will be displayed and the DUAL WATCH icon will
disappear on the display.
Model FR-1000Series
Page 15
SETTING THE RADIO TO NOAA WEATHER RADIO MODE
To set the FR-1000 to NOAA WEATHER RADIO mode, move the BAND
switch in WX position. The LCD will show the current WX channel setting,
and the NOAA WEATHER (WX) BAND icon will appear on the display.
Turn the TUNING knob to select one of the 7 NOAA WEATHER (WX)
BAND channels.
NOAA WEATHER ALERT
Your FR-1000 has a NOAA WEATHER ALERT function, to enable you to
automatically receive weather alert from designated NOAA stations.
To turn the NOAA WEATHER (WX) ALERT on, turn the FUNCTION switch
to . The NOAA WEATHER (WX) ALERT icon will appear on the display
while on the right an "oF" icon appears. Select "on" by turning the TUN-
ING knob. To confirm, press the PTT or the MENU button. The radio will
return to WX BAND and the NOAA WEATHER (WX) ALERT icon will
remain on the display. If the radio receives a WX ALERT signal from a des-
ignated NOAA station while on WX mode, the radio will beep for 20 sec-
onds while an "AL" and "In" icon appear on the display while the FLASH-
LIGHT and the display illumination will blink altogether. Afterwhich the
radio will automatically go to NOAA WEATHER RADIO mode.
If the radio receives a WX ALERT signal from a designated NOAA station
while on AM/FM or GMRS/FRS mode, the radio will beep for 20 seconds
while the NOAA WEATHER (WX) ALERT icon will appear blinking on the
display while the FLASHLIGHT and the display illumination will blink
altogether. In this case, the user should set the BAND switch to WX
position to listen for any weather alert broadcast.
The NOAA WEATHER (WX) ALERT icon will remain blinking on the
display when it receives a WX ALERT signal unless the BAND switch
is set to WX mode or any button is pressed. This is to remind the user
that a WX Alert signal have been received in case they missed it.
To turn the NOAA WEATHER (WX) ALERT off, press the MENU button
once while in WX Band. The NOAA WEATHER (WX) ALERT icon will
appear on the display while on the right an "oF" icon appears. Select "oF"
by turning the TUNING knob. To confirm, press the PTT or MENU button.
Model FR-1000Series
Page 16
SETTING THE RADIO TO AM/FM RECEIVER MODE
To set the FR-1000 to AM/FM RECEIVER mode, move the BAND switch in
AM or FM position. The LCD will show the current AM or FM channel
setting.
CHANNEL SELECTION (AM/FM BAND)
Turn the TUNING knob clockwise or counter-clockwise to select the AM or
FM frequency. Turning and holding the TUNING knob will make the radio
scan for the frequency continuously until it receives a strong signal.
SETTING THE RADIO
TO CLOCK MODE
To set the FR-1000 to CLOCK mode, just turn the BATTERY SOURCE
switch to OFF. The display will show the current time setting.
CHANGING
THE HOUR SETTING
To change the hour setting of the clock, press the SCAN/HOUR button
while in CLOCK mode, and the hour digit of the clock will blink. Turn the
TUNING knob to change the hour setting. Press the PTT button to confirm.
CHANGING
THE MINUTE SETTING
To change the minute setting of the clock, press the MENU/MINUTE
button while in CLOCK mode, and the minute digit of the clock will blink.
Turn the TUNING knob to change the hour setting. Press the PTT/SELECT
button to confirm.
SETTING THE ALARM CLOCK
The FR-1000 can also function as an ALARM CLOCK. To turn the ALARM
CLOCK on, press the ALARM ON/OFF button while in CLOCK mode. The
ALARM CLOCK icon will appear.
To set the hour setting of the ALARM, press the SCAN/HOUR button while
in CLOCK mode, and the hour digit of the clock will blink. Turn the
TUNING knob to change the hour setting. Press the PTT/SELECT button
to confirm.
To set the minute setting of the ALARM, press the SCAN/MINUTE button
while in CLOCK mode, and the minute digit of the clock will blink. Turn the
TUNING knob to change the minute setting. Press the PTT button to
confirm.
To turn the ALARM CLOCK off, press the ALARM ON/OFF button while in
CLOCK mode. The ALARM CLOCK icon will disappear.
ALARM CLOCK SNOOZE
When the ALARM CLOCK goes off, you can activate the SNOOZE
function by pressing the SNOOZE button. Everytime the SNOOZE button
is pressed the the ALARM CLOCK will go off again after 8 minutes.
Model FR-1000Series
Page 17
USING THE FLASHLIGHT
Your FR-1000 Series has a built-in FLASHLIGHT.
To turn the FLASHLIGHT on, turn the FUNCTION switch to .
To turn the FLASHLIGHT off, set the FUNCTION switch to OFF.
USING THE S.O.S.
Your FR-1000 Series has a SOS function. During this, a RED LED will blink
to serve as beacon light.
To turn the SOS on, turn the FUNCTION switch to .
To turn the SOS off, set the FUNCTION switch to OFF.
USING
THE SIREN
Your FR-1000 Series has a built-in SIREN.
To turn the SIREN on, turn the FUNCTION switch to .
To turn the SIREN off, set the FUNCTION switch to OFF
Model FR-1000Series
Page 17
EXTERNAL SPEAKER/MICROPHONE JACK
Your FR-1000 Series can be used with an optional external speaker/
microphone or headset, freeing your hands for other tasks. You can also
use the HAND MIC thru the SPEAKER/MICROPHONE JACK.
To use an optional speaker/microphone or headset:
lOpen the SPEAKER/MIC Jack Rubber Cap on the side radio.
lInsert the plug(s) into the SPK/MIC jacks.
lPlace the earbud into your ear, and adjust the mic into your desired
position.
PHONE CHARGER JACK
Your FR-1000 Series can be used to charge a mobile phone by the
DYNAMO CRANK, AC, or DC Adapter thru the PHONE CHARGER Jack.
lOpen the PHONE CHARGER Jack Rubber Cap on the side radio.
lAttach a Charging Cable (not included) to the mobile phone.
lConnect the other end of the Charging Cable to the PHONE
CHARGER Jack of the FR-1000.
lRecharge the mobile phone battery by turning rapidly the DYNAMO
CRANK, or by attaching the AC or DC Adapter in the Charging Jack .
Note: Charging a mobile phone thru the Phone Charger Jack is
intended for emergency purpose only. It is not intended for
recharging fully a discharged battery.
Model FR-1000Series
Page 18
No Power - Check battery installation and/or replace batteries
Cannot Receive
Messages - Confirm the radios have the same channel
and Privacy Code settings.
- Make sure that you are within range of the other
transceivers.
- Buildings and other structures may interfere with
your communication.
(See ABOUT RANGE on Page 10)
Radio is not responding to
button presses - Make sure key lock is not on. See "Keypad Lock"
(Page 12).
- Radio might need to be reset. Turn radio off then
on.
- Ensure accessory microphone is set properly
Display is dim - Recharge or replace batteries.
Charger not functioning - Ensure that the Charger Plug is installed in the radio
properly.
- Ensure the outlet where the charger is plugged
into is functioning properly.
- Check that the battery pack is installed in the
radio properly.
USE AND CARE
1. Use a soft damp cloth to clean the radio
2. Do not use alcohol or cleaning solutions to clean the radio.
3. Do not immerse the radio in water.
4. Dry the radio with dry lint-free cloth should it get wet.
5. Turn off the radio and remove the batteries during long-term storage.
If you have a problem which you believe requires service, please call
first and speak with a service technician. Many problems can be
remedied over the phone without returning the unit for service.
TROUBLESHOOTING GUIDE
Model FR-1000Series
Page 19
SPECIFICATIONS
Channels 22 GMRS/FRS Channels +121 Privacy Codes
7 NOAA Weather (WX) Band Channels
Operating Frequency UHF 462.5500 ~ 467.7125 MHz
AM : 520kHz ~ 1710kHz -10kHz steps
FM : 87.5MHz ~ 108.0MHz - 100kHz steps
Power Source 4 AA Alkaline or 6.0V Rechargeable Ni-MH battery pack
GMRS/FRS FREQUENCY CHART (MHz)
CH. No CH. Freq. CH. No CH. Freq. CH. No CH. Freq.
1 462.5625 9 467.5875 17 462.6000
2 462.5875 10 467.6125 18 462.6250
3 462.6125 11 467.6375 19 462.6500
4 462.6375 12 467.6625 20 462.6750
5 462.6625 13 467.6875 21 462.7000
6 462.6875 14 467.7125 22 462.7250
7 462.7125 15 462.5500
8 467.5625 16 462.5750
NOAA WEATHER (WX) RADIO FREQUENCY CHART (MHz)
CH. No CH. Freq. CH. No CH. Freq.
1 162.400 6 162.525
2 162.425 7 162.550
3 162.450
4 162.475
5 162.500
PRIVACY CODES FREQUENCY CHART (Hz)
Code Freq. Code Freq. Code Freq. Code Freq. Code Freq.
1 67.0 9 91.5 17 118.8 25 156.7 33 210.7
2 71.9 10 94.8 18 123.0 26 162.2 34 218.1
3 74.4 11 97.4 19 127.3 27 167.9 35 225.7
4 77.0 12 100.0 20 131.8 28 173.8 36 233.6
5 79.7 13 103.5 21 136.5 29 179.9 37 241.8
6 82.5 14 107.2 22 141.3 30 186.2 38 250.3
7 85.4 15 110.9 23 146.2 31 192.8
8 88.5 16 114.8 24 151.4 32 203.5
* Channels 8~14 are low-power FRS license free channels
Note: Privacy codes can be programmed for use on any channel
Model FR-1000Series
Page 20
DCS PRIVACY CODE CHART
No.
CODE No. CODE No. CODE
1 023 29 174 57 445
2 025 30 205 58 464
3 026 31 223 59 465
4 031 32 226 60 466
5 032 33 243 61 503
6 043 34 244 62 506
7 047 35 245 63 516
8 051 36 251 64 532
9 054 37 261 65 546
10 065 38 263 66 565
11 071 39 265 67 606
12 072 40 271 68 612
13 073 41 306 69 624
14 074 42 311 70 627
15 114 43 315 71 631
16 115 44 331 72 632
17 116 45 343 73 654
18 125 46 346 74 662
19 131 47 351 75 664
20 132 48 364 76 703
21 134 49 365 77 712
22 143 50 371 78 723
23 152 51 411 79 731
24 155 52 412 80 732
25 156 53 413 81 734
26 162 54 423 82 743
27 165 55 431 83 754
28 172 56 432 - -
Note: Privacy codes can be programmed for use on any channel