Ezurio 1110200 902-928 MHz FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER User Manual

AeroComm Corporation 902-928 MHz FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER UserMan LT1110200

a href="https://usermanual.wiki/Ezurio" itemprop="url"> Ezurio >

Users Manual

LT1110-200 Compliance Information 1.1 AGENCY IDENTIFICATION NUMBERS Family US/FCC CANADA/IC LT1110-200 KQL-1110200 2268C-1110200 LT1110-200 FAMILY Part # Description Packaging PRM240 (+23 dBm), Pluggable with U.FL connector PLG-U.FL PRM241 (+23dBm), Pluggable with -1dBi integrated antenna PLG-ANT 1.2 APPROVED ANTENNA LIST LT1110-200 family has been designed to operate with the antennas listed below and having a maximum gain of 6dBd. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and gain should be chosen so that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. The OEM is free to choose another vendor’s antenna of like type and equal or lesser gain as an antenna appearing in the table and still maintain compliance. Item Part Number Mfg. Type Gain 1 0915AT43A0026 Johanson Chip -1dBi 2 S467FL-6-PX-915S Nearson Dipole 2dBi 3 FG9026 Laird Technologies Omni 6dBd 4 YS8963 Laird Technologies Yagi 6dBd 1.3 FCC/ IC REQUIREMENTS FOR MODULAR APPROVAL In general, there are two agency classifications of wireless applications; portable and mobile. Portable – Portable is a classification of equipment where the user, in general, will be within 20 cm of the transmitting antenna. Portable equipment is further broken down into two classes; within 2.5 cm of human contact and beyond 2.5 cm. The LT1110-10 family is not agency approved for portable applications. The OEM is required to have additional evaluation performed to receive this classification. Contact Laird Technologies for more details.
Mobile – Mobile defines equipment where the user will be 20 cm or greater from the transmitting equipment. The antenna must be mounted in such a way that it cannot be moved closer to the user with respect to the equipment, although the equipment may be moved. This equipment has been approved for mobile applications where the equipment should be used at distances greater than 20 cm from the human body. 1.4 CAUTION Any changes or modifications not expressly approved by Laird Technology could void the user’s authority to operate this equipment. The LT1110-200 is a 902-928 MHz Frequency Hopping Spread Spectrum transmitter. This module is designed to be installed, operated, and used by system integrators and/or professional installers. As such, the product is required to comply with all applicable FCC equipment authorization regulations, requirements and equipment functions not associated with the transmitter module. The OEM is responsible for demonstration of compliance to regulations for non-transmitter components within the host product to requirements for unintentional radiators (Part 15B), such as digital devices and to additional authorization requirements for the non-transmitter functions of the transmitter module (i.e., Verification, or Declaration of Conformity) (e.g., Bluetooth and WiFi transmitter modules). 1.5 NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does not cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Re-orient or relocate the receiving antenna  Increase the separation between the equipment and the receiver  Connect the equipment to an outlet on a circuit that is different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. 1.6 OEM EQUIPMENT LABELING REQUIREMENTS The OEM must ensure that FCC labeling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate identifier for this product as well as the FCC notice below. Contains FCC ID: KQL-1110200 IC: 2268C-1110200 This enclosed device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Label and text information should be in a size of type large enough to be readily legible, consistent with the dimensions of the equipment and the label. However, the type size for the text is not required to be larger than eight point.
Download:
Mirror Download [FCC.gov]
Document ID1547909
Application IDCrX1ZP7J2TKHnZF48bEPYQ==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize2.12kB (26477 bits)
Date Submitted2011-09-23 00:00:00
Date Available2011-09-23 00:00:00
Creation Date2011-09-19 14:33:49
Producing SoftwareAcrobat Distiller 9.4.6 (Windows)
Document Lastmod2011-09-19 14:33:49
Document TitleMicrosoft Word - UserMan LT1110200
Document CreatorPScript5.dll Version 5.2.2
Document Author: Desk
FCC ID Filing: KQL-1110200

Navigation menu