GE MDS LEDR400S-74 LEDR 400S Microwave Radio User Manual

GE MDS LLC LEDR 400S Microwave Radio 3627C LEDR Body

a href="https://usermanual.wiki/GE-MDS" itemprop="url"> GE MDS >

Contents

Operating Instructions Part 1 of 2

Installation and Operation Guide P/N 05-3627A01, Rev. CMARCH 2001 LEDR 400S/F, 900S/F, 1400S/F Series Including Protected (1+1) and Space Diversity Versions LEDR DIGITAL MICROWAVE RADIOS
LEDR Series radios are supplied from the factory in matched pairs and will be configured to user’s specifications. There are a few steps necessary to place the pair on-the-air communi-cating with each other. Once this is done, system-specific parameters will need to be reviewed and changed to match your requirements. Below are the basic steps for installing the LEDR radio. For a more detailed installation procedure, please see “INITIAL STARTUP AND CONFIG-URATION” on page 24. When making cable connections, refer to Section 3.6, Rear Panel Con-nectors, on page 16 for a rear panel view of the radio. 1. Install and connect the antenna system to the radio • Ensure a path study has been conducted and that the radio path is acceptable. • Use good quality, low loss coaxial cable. Keep the feedline as short as possible.• Preset directional antennas in the direction of desired transmission/reception. 2. Connect the data equipment to the rear panel data interface • The data interface should be an RJ-45 connector for Fractional-T1, Fractional-E1, or E1, and DB-25 for EIA-530. • Verify the customer premises data equipment is configured as DTE. (By default, the LEDR radio is configured as DCE.) 3. Apply DC power to the radio • Verify that the line voltage matches the power supply input range (24 Vdc or 48 Vdc).• The power connector is a three-pin keyed connector. The power source can be connected with either polarity. The center conductor is not connected. 4. Change SUPER password and set up user access • Login to Network Management System as SUPER , using password SUPER . (See “login” on page 68 .)• Change the password using the PASSWD command. ( See “passwd” on page 73 )• Set up required users, passwords and access levels using the USER command, as required.( See “user” on page 86 ) 5. Set the radio’s basic configuration using front panel or Console interface • Set the transmit/receive frequencies ( TX xxx.xxxx / RX xxx.xxxx ) if they need to be changed from the factory settings. (See “freq” on page 58 .)• Refer to this manual for other configuration settings. 6. Verify and set as necessary the following parameters to allow data throughput and interconnection with the network. • RF transmit and receive frequencies. (See “freq” on page 58 .)• Radio modulation type and data rate parameters. ( See “modem” on page 72 ).• Data interface clocking. ( See “clkmode” on page 54 ).• Data framing. ( See “fstruct” on page 59 ). The Quick Start Guide is continued on the rear cover of this manual.QUICK START GUIDE
Download:
Mirror Download [FCC.gov]
Document ID162757
Application IDpu6QtEhxV7VpPRmnQMb5vA==
Document DescriptionOperating Instructions Part 1 of 2
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize214.76kB (2684478 bits)
Date Submitted2001-08-02 00:00:00
Date Available2001-09-27 00:00:00
Creation Date2001-06-29 15:06:01
Producing SoftwareAcrobat Distiller 4.0 for Macintosh
Document Lastmod2001-06-29 15:07:43
Document Title3627C LEDR Body.book
Document CreatorFrameMaker 5.5
Document Author: MDS Employee
FCC ID Filing: E5M-LEDR400S-74

Navigation menu