Garmin 02723 Wireless Backup Camera User Manual

Garmin International Inc Wireless Backup Camera Users Manual

a href="https://usermanual.wiki/Garmin" itemprop="url"> Garmin >

Users Manual

BC™ 35 WIRELESS BACKUPCAMERAInstallation InstructionsIntroduction WARNINGSee the Important Safety and Product Information guide in the product box forproduct warnings and other important information.Garmin® strongly recommends having an experienced installer with the properknowledge of electrical systems install the device. Incorrectly wiring the powercable can result in damage to the vehicle or the battery and can cause bodilyinjury.When connecting the power cable, do not remove the in-line fuse holder. Toprevent the possibility of injury or product damage caused by fire or overheating,the appropriate fuse must be in place as indicated in the product specifications.In addition, connecting the power cable without the appropriate fuse in place willvoid the product warranty. CAUTIONAlways wear safety goggles, ear protection, and a dust mask when drilling,cutting, or sanding.NOTICEWhen drilling or cutting, always check what is on the opposite side of the surface.These installation instructions do not apply to a specific vehicle type, and aremeant as a guide when installing this product on your vehicle. For questionsspecific to your vehicle, you should contact the vehicle manufacturer.Device OverviewItem DescriptionÀTransmitterÁCameraÂCamera mounting bracketTools Needed• Drill and 10.008 mm, or size X (0.397 in.) drill bitPrinted in TaiwanDecember 2017190-02351-90_01Confidential
• #2 Phillips screwdriver• Screws, bolts, or cable ties (to secure the transmitter)•Solderless wire-splice connector or solder and heat-shrink tubing• RV sealant (optional)InstallationCamera Mounting ConsiderationsWhen selecting a location to mount the camera, observe these considerations.• You should test a mounting location before you permanently mount thecamera.• Installing the camera higher on the back of the vehicle provides a betterviewing angle.• The included bracket can be clipped onto a license plate or other similarsurface, or it can be fastened to the back of the vehicle using the includedself-tapping, panhead screws.Transmitter Location and Wiring ConsiderationsNOTICEThe transmitter is not intended to be held or worn on your body while it is in use.When selecting a location to install the wireless transmitter, observe theseconsiderations.• You should test a proposed installation location before you permanentlyinstall the transmitter.•Some vehicles do not provide constant minimum voltage to the reverselamps. You should use an automotive relay when connecting the transmitterand camera to a power source that does not provide constant voltage.• Although the transmitter can transmit the video signal approximately 45 ft(13.5 m), the location of the transmitter can affect this range.◦ The closer you install the transmitter to the device, the more reliable thesignal.◦ The signal transmits from the flat front and back surfaces À of thetransmitter. The transmitter provides the best signal when either flatsurface points toward the receiver.◦ Dense metal or appliances Á in the path of the transmitter greatly reducethe transmission distance.◦ The fewer solid objects that exist between the path of the transmitter andthe device, the more reliable the signal.•The fuse holder located near the transmitter is not waterproof. Installing thefuse holder in a location that is exposed to the elements is not recommended.• The connector between the camera and the transmitter is not waterproof. Ifyou make this connection in a location exposed to the elements, you mustmake sure that the connection is waterproof.• If you are installing the camera on a boat trailer or other location that may beexposed to water, you must waterproof all wiring connections and the fuseholder in the transmitter cable.Testing the Camera and Transmitter Location1Temporarily secure the camera in the preferred mounting location.2Confidential
2Temporarily place the transmitter in the preferred installation location, andconnect it to power and to the camera.TIP: If you do not want to splice into the wiring of your vehicle for this test,you can connect the transmitter and camera to a 12 Vdc battery.3Test the transmitter for correct operation by viewing the camera on thecompatible Garmin device.NOTE: You may need to pair the camera to the Garmin device before youcan view the image and test the transmitter location (page 4).If you do not see video on the Garmin device at the preferred installationlocation, move the transmitter to another location and test it again.4Repeat steps 2–3 until the transmitter operates correctly.5Test the camera view by observing the video on the device.6If the camera does not provide the optimal view for your vehicle, move it toanother location and test it again.7Repeat steps 5–6 until the camera mounting location provides the optimalview for your vehicle.TIP: Make note of which direction is up when you are testing the camera viewto ensure correct permanent installation.Mounting the CameraBefore you permanently mount the camera, you should test the mounting locationfor the optimal view for your vehicle (page 2).If you have already connected the camera to the bracket, you must firstdisassemble it.1Place the bracket À in the mounting location.2Select an option:• If you are mounting the bracket directly on the surface of your vehicle,mark the locations of the two holes on the bracket Á.• If you are installing the bracket on a license plate, remove one of thelicense plate screws and clip the bracket in place so the hole on thebracket  lines up with the hole on the license plate.3Secure the bracket to the vehicle using either the included self-tappingscrews à or the license-plate screw you removed in step 2 Ä.4Place the camera in the bracket, and determine the best place for the cameracable Å to enter the vehicle.5Using an appropriate drill bit, drill a hole for the camera cable to enter thevehicle.6Feed the camera cable through the hole and route it to the transmitterlocation.7Secure the camera in the bracket using the included hex bolts Æ.3Confidential
Download:
Mirror Download [FCC.gov]
Document ID3682162
Application ID05bgAuR0NMVXxodl90FgnQ==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize61.1kB (763788 bits)
Date Submitted2017-12-18 00:00:00
Date Available2018-03-28 00:00:00
Creation Date2017-12-15 11:23:33
Producing SoftwareAntenna House PDF Output Library 6.3.815 (Windows (x64))
Document Lastmod2017-12-15 11:23:33
Document TitleUsers Manual
Document CreatorAH XSL Formatter V6.3 MR3 for Windows (x64) : 6.3.4.25128 (2016/07/01 17:39JST)
FCC ID Filing: IPH-02723

Navigation menu