GemTek Technology A931208G T-511 54Mbps High Gain Smart Ethernet Client User Manual Copyright and Trademarks

Gemtek Technology Co., Ltd. T-511 54Mbps High Gain Smart Ethernet Client Copyright and Trademarks

Users Manual

        Dual-Band Wireless A+G     PCI Adapter                        Use this guide to install:  WMP55AG ver. 1.3                                                                   Copyright and Trademarks
Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2004 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.     Table of Contents   Chapter 1: Introduction 1   Welcome   What’s in this Guide?     Chapter 2: Planning Your Wireless Network 4   Network Topology   Roaming   Network Layout   Chapter 3: Getting to Know the Dual-Band Wireless A+G PCI Adapter   The LED Indicators     Chapter 4: Software Installation and Configuration     The Installation Procedure     Chapter 5: Hardware Installation     Connecting the Adapter     Chapter 6: Using the WLAN Monitor     Accessing the WLAN Monitor     Link Information   Site Survey   Profiles Creating a New Profile Appendix A: Troubleshooting   Common Problems and Solutions     Frequently Asked Questions     Appendix B: Wireless Security Security Precautions   Security Threats Facing Wireless Networks     Appendix C: Windows Help     Appendix D: Glossary     Appendix E: Specifications     Appendix F: Warranty Information     Appendix G: Regulatory Information     Appendix H: Contact Information
Chapter 1: Introduction   Welcome   Thank you for choosing the Dual-Band Wireless A+G PCI Adapter. With this Adapter, your wireless networking experience will be faster and easier than ever.   The Linksys Dual-Band Wireless A+G PCI Adapter lets your PC communicate with all three wireless network standards. With one PCI Adapter, you can connect to Wireless-A (802.11a), Wireless-G (802.11g) and Wireless-B (802.11b) networks.   Wireless-B networks have a data rate of 11Mbps, and are commonly found in corporate environments and in homes for household Internet connectivity without the need for running cables. They're also popping up all over the country in coffee shops, airports, hotels, convention centers, and other public spaces offering “on the go” connectivity to mobile users.   In high speed or heavy usage environments, Wireless-B is quickly being replaced by a new standard, Wireless-G, which uses the same 2.4GHz radio band, but at 54Mbps, is almost five times faster. The third wireless network standard is Wireless-A, which also runs at 54Mbps, but operates in the less-crowded 5GHz radio band.   Wireless-A is mostly used in corporate installations.   Whichever standard you encounter, the Dual-Band Wireless A+G PCI Adapter is ready to connect. And it's simple to use. Just run the included Setup Wizard, which will walk you through the configuration, and insert the PCI Adapter into one of your PC’s empty PCI slots. All wireless communications can be protected by up to 256-bit encryption, so your data stays secure.   Use the instructions in this Guide to help you set up and install the Adapter. These instructions should be all you need to get the most out of the Dual-Band Wireless A+G PCI Adapter.   What’s in this Guide?   This user guide covers the steps for setting up and using the Dual-Band Wireless A+G PCI Adapter.  • Chapter 1: Introduction   This chapter describes the Adapter’s applications and this User Guide.   • Chapter 2: Planning Your Wireless Network   This chapter discusses a few of the basics about wireless networking.   • Chapter 3: Getting to Know the Dual-Band Wireless A+G PCI Adapter   This chapter describes the physical features of the Adapter.   • Chapter 4: Software Installation and Configuration   This chapter instructs you on how to use the Adapter’s Setup Wizard and configure the Adapter.   • Chapter 5: Hardware Installation   This chapter shows you how to connect the Adapter to your PC.   • Chapter 6: Using the WLAN Monitor   This chapter show you how to use the Adapter’s WLAN Monitor.   • Appendix A: Troubleshooting   This appendix describes some potential problems and solutions, as well as frequently asked questions, regarding installation and use of the Adapter.   • Appendix B: Wireless Security   This appendix discusses security issues regarding wireless networking and measures you can take to help protect your wireless network.   • Appendix C: Windows Help   This appendix describes how you can use Windows Help for instructions about networking, such as installing the TCP/IP protocol.   • Appendix D: Glossary   This appendix gives a brief glossary of terms frequently used in networking.   • Appendix E: Specifications   This appendix provides the Adapter’s technical specifications.   • Appendix F: Warranty Information   This appendix supplies the Adapter’s warranty information.   • Appendix G: Regulatory Information
This appendix supplies the Adapter’s regulatory information.   • Appendix H: Contact Information   This appendix provides contact information for a variety of Linksys resources, including Technical Support.  Chapter 2: Planning Your Wireless Network   Network Topology   A wireless network is a group of computers, each equipped with one wireless adapter. Computers in a wireless network must be configured to share the same radio channel. Several PCs equipped with wireless cards or adapters can communicate with one another to form an ad-hoc network.   Linksys wireless adapters also provide users access to a wired network when using an access point or wireless router. An integrated wireless and wired network is called an infrastructure network. Each wireless PC in an infrastructure network can talk to any computer in a wired network infrastructure via the access point or wireless router.   An infrastructure configuration extends the accessibility of a wireless PC to a wired network, and can double the effective wireless transmission range for two wireless adapter PCs. Since an access point is able to forward data within a network, the effective transmission range in an infrastructure network can be doubled.   Roaming   Infrastructure mode also supports roaming capabilities for mobile users. Roaming means that you can move your wireless PC within your network and the access points will pick up the wireless PC's signal, providing that they both share the same SSID.   Before enabling roaming, choose a feasible radio channel and optimum access point position. Proper access point positioning combined with a clear radio signal will greatly enhance performance.  infrastructure: a wireless network that is   bridged to a wired network via an access point.   ad-hoc: a group of wireless devices   communicating directly with each other (peerto-   peer) without the use of an access point.   roaming: the ability to take a wireless device   from one access point's range to another without   losing the connection.   ssid: your wireless network's name.   topology: the physical layout of a network.   Network Layout   Dual-Band Wireless A+G products offer the most flexibility, because they can connect to 802.11a networks, or they can connect to networks with 802.11g and/or 802.11b devices—depending on the settings you configure on the dual-band products.   The Dual-Band Wireless A+G PCI Adapter is compatible with all 802.11a, 802.11b, and 802.11g routers, as well as access points. It will also communicate with wireless Notebook Adapters for your laptop computers, wireless PCI adapters for your desktop PCs, and wireless USB adapters when you want to enjoy USB connectivity. Wireless products will also communicate with wireless print servers.   When you wish to connect your wired network with your wireless network, network ports on access points and wireless routers can be connected to any of Linksys's switches or wired routers.  With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at www.linksys.com for more information about wireless products.
  Chapter 3: Getting to Know the Dual-Band Wireless A+G PCI Adapter   The LED Indicators   The Adapter's LEDs display information about network activity.   ACT Green. The ACT LED lights up when the Adapter has an active connection. It flashes when data is transmitted or received.     Chapter 4: Software Installation and Configuration   The Dual-Band Wireless A+G PCI Adapter Setup Wizard will guide you through the installation procedure. The Setup Wizard will install the driver and WLAN Monitor, as well as configure the Adapter.  Insert the Setup Wizard CD-ROM into your CD-ROM drive. The Setup Wizard should run automatically, and the Welcome screen should appear. If it does not, click the Start button and choose Run. In the field that appears, enter D:\setup.exe (if “D” is the letter of your CD-ROM drive).  On the Welcome screen, you have the following choices:   Install - Click the Install button to begin the software installation process.   User Guide - Click the User Guide button to open the PDF file of this User Guide.   Exit - Click the Exit button to exit the Setup Wizard.          The Installation Procedure   1. To install the Adapter, click the Install button on the Welcome screen.  2. After reading the License Agreement, click the Next button if you agree, or click the Cancel button to end the installation.   3. The Setup Wizard will ask you to choose a network mode. Click the 5GHz + 2.4GHz radio
button if you will connect to both 802.11a and 802.11g networks. Click the 5GHz radio button if you will connect only to 802.11a networks. Click the 2.4GHz radio button if you will connect only to 802.11g or 802.11b networks.   Click the Next button.  4. The Setup Wizard will ask you to choose a wireless mode. Click the Infrastructure Mode radio button if you want your wireless computers to network with computers on your wired network using a wireless access point. Click the Ad-Hoc Mode radio button if you want multiple wireless computers to network directly with each other.   The Setup Wizard provides three SSID fields. In the SSID 1 field, enter the SSID of your wireless network. The SSID must be identical for all devices in the network. The default setting is linksys (all lowercase).   In the SSID 2 and SSID 3 fields, enter alternative SSIDs. When attempting to connect to the network, the Adapter will first try SSID 1. If the Adapter fails to connect, then it will try SSID 2 and SSID 3 until it establishes a connection. Click the Next button.  5. If you chose Infrastructure Mode, go to Step 6 now. If you chose Ad-Hoc Mode, select the correct operating channel for your network. If you have an 802.11g network, then select the Network Mode from the drop-down menu. Click the Next button, and go to Step 6. Click the Back button to change any settings.   Channel - The channel you choose should match the channel set on the other devices in your wireless network. If you are unsure about which channel to use, select Auto, which enables the Adapter to match the channel setting of the strongest wireless signal it detects.   Network Mode - If you have 802.11b and 802.11g devices in your network, then select Mixed Mode. Both Wireless-G and Wireless-B computers will be allowed on the network, but transmission speeds will be reduced. If you have only 802.11g devices in your network, select G-Only Mode for maximum speed (no Wireless-B users will be allowed on the network).   6. The Setup Wizard will ask you to review your settings before it starts to copy files. Click the Next button to save these settings, or click the Back button to change any settings.   7. After the software has been successfully installed, the Congratulations screen will appear. Click the Exit button. At this point, you may be asked to restart your computer.  Proceed to “Chapter 5: Hardware Installation.”    Chapter 5: Hardware Installation   Connecting the Adapter   1. Turn off your desktop PC.   2. Open your PC’s case, and locate an available PCI slot on the motherboard. Check with your computer’s manufacturer if you need instructions.   3. Slide the Adapter into the PCI slot. Make sure that all of its pins are touching the slot’s contacts. You may have to apply a bit of pressure to slide the Adapter all the way in.   4. After the Adapter is set firmly in place, secure its fastening tab to your PC’s chassis with a mounting screw.   Then close your PC’s case.   5. Rotate the antenna so that it is positioned straight up and perpendicular to the horizon. This will ensure optimum wireless operating range and performance.   6. Power on your desktop PC.   7. Windows will detect the new hardware and begin installing the driver files in your operating system.  Note: For Windows 2000 users, you may be informed that a digital signature has not been found after Windows detects the new hardware. This is normal, and it has been verified that the Adapter does work with Windows 2000. Click the Yes button to continue. Some Windows users may be asked to restart their computers.   Congratulations! The installation of the Dual-Band Wireless A+G PCI Adapter is complete.   If you want to check the link information, search for available wireless networks, or make additional   configuration changes, go to “Chapter 6: Using the WLAN Monitor.”
        Chapter 6: Using the WLAN Monitor   Use the WLAN Monitor to check the link information, search for available wireless networks, or create profiles that hold different configuration settings.   Accessing the WLAN Monitor   After installing the Adapter, the Dual-Band Wireless A+G PCI Adapter WLAN Monitor icon will appear in your system tray. Double-click the icon.   The Link Information screen will appear. From this screen, you can find out how strong the current wireless signal is and how good the connection’s quality is. You can also click the More Information button to view additional status information about the current wireless connection. To search for available wireless networks, click the Site Survey tab. To perform configuration changes, click the Profiles tab.  Link Information   The Link Information screen displays network mode, signal strength, and link quality information about the current connection. It also provides a button to click for additional status information.   Ad-Hoc Mode or Infrastructure Mode - The screen indicates whether the Adapter is currently working in ad-hoc or infrastructure mode.   Signal Strength - The Signal Strength bar indicates signal strength, from 0 to 100%.   Link Quality - The Link Quality bar indicates the quality of the wireless network connection, from 0 to 100%.   Click the More Information button to view additional information about the wireless network connection.  Click the X (Close) button in the upper right corner to exit the WLAN Monitor.
Network Settings   The Networks Settings screen provides information on your current network settings.   Status - The status of the wireless network connection.   SSID - The SSID of the wireless network.   Channel - The channel to which the wireless network devices are set.   Security - The status of the security feature.   Network Type - The wireless mode currently in use, Infrastructure or Ad-Hoc.   IP Address - The IP Address of the Adapter.   Subnet Mask - The Subnet Mask of the Adapter.   Default Gateway - The Default Gateway address of the Adapter.   DNS - The DNS address of the Adapter.   MAC - The MAC address of the wireless network’s access point.   Click the Statistics button to go to the Network Statistics screen.  Click the Back button to return to the initial Link Information screen.  Click the X (Close) button in the upper right corner to exit the WLAN Monitor.   Network Statistics   The Networks Statistics screen provides statistics on your current network settings.   Transmit Rate - The data transfer rate of the current connection.(In Auto mode, the Adapter dynamically shifts to the fastest data transfer rate possible at any given time.)   Receive Rate - The rate that data is received.   Authentication - The current security authentication mode.   Network Mode - The mode of the wireless network currently in use, 802.11a, 802.11b, or 802.11g.  Transmit Total - The total number of packets being transmitted.   Receive Total - The total number of packets being received.   Signal to Noise - This tells you the quality of your signal. The higher the number, the better your signal.  Click the Settings button to go to the Settings screen.  Click the Back button to return to the initial Link Information screen.  Click the X (Close) button in the upper right corner to exit the WLAN Monitor.   Site Survey   The Site Survey screen displays a list of infrastructure and ad-hoc networks available for connection in the table on the left. This table shows the network’s SSID, channel, and the quality of the wireless signal the Adapter is receiving. You may click SSID, Channel, or Signal, to sort by that field.   Site Information   For each network selected, the following settings are listed:   Network Type - The wireless mode currently in use, Infrastructure or Ad-Hoc.   Channel - The channel to which the wireless network devices are set.   WEP - The status of the encryption security feature.   MAC - The MAC address of the wireless network’s access point.   Surveyed at - The time at which the wireless network was scanned.   Refresh - Click the Refresh button to perform a new search for wireless devices.   Connect - To connect to one of the networks on the list, select the wireless network, and click the Connect button  Click the X (Close) button in the upper right corner to exit the WLAN Monitor.   Profiles   The Profiles screen lets you save different configuration profiles for different network setups. The table on the left displays a list of infrastructure and ad-hoc networks available for connection. This table shows the network’s profile name and SSID, as set in the connection profile.   Profile Information   For each profile selected, the following are listed:   Network Type - The mode of the wireless network currently in use, Infrastructure or Ad-Hoc.   Transfer Rate - The Adapter is set to Auto mode, so it will dynamically shift to the fastest data
transfer rate possible at any given time.   Channel - The channel to which the wireless network devices are set. (Auto indicates that the Adapter will use the channel setting of the network’s access point.)   WEP - The status of the encryption security feature.   Connect - To connect to a wireless network using a specific profile, select the profile, and click the Connect button.  Edit - Select a profile, and click the Edit button to change an existing profile.   New - Click the New button to create a new profile. See the next section, “Creating a New Profile,” for detailed instructions.   Import - Click the Import button to import a profile that has been saved in another location. Select the appropriate file, and click the Open button.  Export - Select the profile you want to save in a different location, and click the Export button. Direct Windows to the appropriate folder, and click the OK button.  Delete - Click the Delete button to delete a profile.   Click the X (Close) button in the upper right corner to exit the WLAN Monitor.   NOTE: If you want to export more than one profile, you have to export them one at a time.   Creating a New Profile   1. On the Profiles screen, click the New button to create a new profile.   2. Enter a name for the new profile, and click the OK button. Click the Cancel button to return to the Profiles screen without entering a name.  3. The Profile Wizard screen will appear. Select 2.4GHz + 5GHz if you will connect to 802.11a or 802.11g networks. Select 5GHz if you will only connect to 802.11a networks. Select 2.4GHz if you will only connect to 802.11g networks. Click the Next button.  4. The Network Setting screen will appear next. If your network has a DHCP server, click the radio button next to Obtain an IP address automatically (DHCP). Click the Next button to continue, or click the Cancel button to return to the Profiles screen.  If your network does not have a DHCP server, click the radio button next to Specify the IP Setting. Enter an IP Address, Subnet Mask, Default Gateway, and DNS appropriate for your network. You must specify the IP Address and Subnet Mask on this screen. If you are unsure about the Default Gateway and DNS address, leave these fields empty. Click the Next button to continue, or click the Cancel button to return to the Profiles screen.   IP Address - This IP Address must be unique to your network.   Subnet Mask - The Adapter’s Subnet Mask must be the same as your wired network’s Subnet Mask.  Default Gateway - Enter the IP address of your network’s Gateway here.   DNS 1 and DNS 2 - Enter the DNS address of your (wired) Ethernet network here.   5. The Choose a network type screen shows a choice of two wireless modes. Click the Infrastructure Mode   radio button if you want your wireless computers to communicate with computers on your wired network via a wireless access point. Click the Ad-Hoc Mode radio button if you want multiple wireless computers to communicate directly with each other. Enter the SSID for your network in the SSID 1 field. Enter alternative SSIDs in the SSID 2 and SSID 3 fields.  Click the Next button to continue or the Back button to return to the previous screen.   Infrastructure Mode - This mode allows wireless and wired networks to communicate through an access point.   Ad-Hoc Mode - This mode allows wireless-equipped computers to communicate directly with each other. No access point is used.   SSID 1-3 - The network name. It must be used for all the devices in your wireless network. It is case sensitive.   It should be a unique name to help prevent others from entering your network.   When attempting a connection, the Adapter will first try SSID 1. If unsuccessful, the Adapter will then try SSID 2 and SSID 3 until it establishes a connection.   6. The Wireless Settings screen will appear. If you chose Infrastructure Mode, go to Step 6 now. If you chose Ad-Hoc Mode, select the correct operating channel for your network from the Channel drop-down menu. If you are setting up an 802.11g profile, then select the Network Mode
from the drop-down menu. Click the Next button, and go to Step 6. Click the Back button to change any settings.   Channel - The channel you choose should match the channel set on the other devices in your wireless network. If you are unsure about which channel to use, select Auto, which enables the Adapter to match the channel setting of the strongest wireless signal it detects.   Network Mode (available for 802.11g only)- To allow both Wireless-G and Wireless-B computers on the network, even though transmission speeds may be reduced, select Mixed Mode. If you have only Wireless-G computers on your network, select G-Only Mode for maximum speed (no Wireless-B computers will be allowed on this network).   7. The Security Setting screen will appear. Select WEP, WPA-PSK, WPA-RADIUS, RADIUS, or LEAP for the Encryption Type. WEP stands for Wired Equivalent Privacy, while WPA-PSK stands for Wi-Fi Protected Access   - Pre-Shared Key. WPA is a security standard stronger than WEP encryption. RADIUS stands for Remote Authentication Dial-In User Service, while LEAP stands for Lightweight Extensible Authentication Protocol. If you don’t want to use encryption, select Disabled.  Click the Next button to continue or the Back button to return to the previous screen.   Proceed to the appropriate section for your Encryption Type: WEP, WPA-PSK, WPA-RADIUS, RADIUS, or LEAP. If you do not want to use encryption, proceed to step 8   WEP  WEP - After you select WEP and click the Next button, the next WEP Security Settings screen will appear.   Select 64-Bit, 128-Bit, or 152-Bit from the drop-down menu (152-bit WEP encryption is available only for 802.11a networking). Then enter a pass phrase or WEP key.   Authentication - You have two choices, Open or Shared Key. The default is set to Open. Open key is when the sender and the recipient do not share a WEP key for authentication. Shared Key is when both the sender and the recipient share a WEP key for authentication. All devices on your network must use the same authentication type.   Pass phrase (not available for 152-bit encryption) - Instead of manually entering a WEP key, you can enter a pass phrase in the Pass phrase field, so WEP keys are automatically generated. It is case-sensitive and should   not be longer than 16 alphanumeric characters. This pass phrase must match the pass phrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)   Transmit Key - The default transmit key number is 1. If your network’s access point or wireless router uses transmit key number 2, 3, or 4, select the appropriate number from the Transmit Key drop-down box.   Key 1-4 - If you are not using a Pass phrase, then manually enter your WEP key(s). The WEP keys you enter must match the WEP keys of your wireless network. If you are using 64-bit WEP encryption, then each key must consist of exactly 10 hexadecimal characters. If you are using 128-bit WEP encryption, then each key must consist of exactly 26 hexadecimal characters. If you are using 152-bit WEP encryption, then each key must consist of exactly 32 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.   Click the Next button to continue, and then go to step 8. Click the Back button to return to the previous screen.   WEP  WEP - After you select WEP and click the Next button, the next WEP Security Settings screen will appear.   Select 64-Bit, 128-Bit, or 152-Bit from the drop-down menu (152-bit WEP encryption is available only for 802.11a networking). Then enter a pass phrase or WEP key.   Authentication - You have two choices, Open or Shared Key. The default is set to Open. Open key is when the sender and the recipient do not share a WEP key for authentication. Shared Key is when both the sender and the recipient share a WEP key for authentication. All devices on your network must use the same authentication type.   Pass phrase (not available for 152-bit encryption) - Instead of manually entering a WEP key, you can enter a pass phrase in the Pass phrase field, so WEP keys are automatically generated. It is
case-sensitive and should not be longer than 16 alphanumeric characters. This pass phrase must match the pass phrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)   Transmit Key - The default transmit key number is 1. If your network’s access point or wireless router uses transmit key number 2, 3, or 4, select the appropriate number from the Transmit Key drop-down box.   Key 1-4 - If you are not using a Passphrase, then manually enter your WEP key(s). The WEP keys you enter must match the WEP keys of your wireless network. If you are using 64-bit WEP encryption, then each key must consist of exactly 10 hexadecimal characters. If you are using 128-bit WEP encryption, then each key must consist of exactly 26 hexadecimal characters. If you are using 152-bit WEP encryption, then each key must consist of exactly 32 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.   Click the Next button to continue, and then go to step 8. Click the Back button to return to the previous screen.   WPA-RADIUS  WPA-RADIUS features WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) WPA RADIUS offers two encryption types, TKIP and AES, with dynamic encryption keys, as well as two authentication methods, EAP-TLS and EAP-PEAP.   After you select WPA-RADIUS and click the Next button, the TkIP Setting screen will appear.   Encryption Type - Select the type of algorithm your network is using, TKIP or AES.  Click the Next button to continue. Click the Back button to return to the previous screen.   The EAP settings screen will appear next. Select EAP-TLS or EAP-PEAP from the Authentication Method drop-down menu. The options are described on the next page.  EAP-TLS  If you selected EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the name of the server in the Server Name field. From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network.   Click the Next button to continue, and then go to step 8. Click the Back button to return to the previous screen.   EAP-PEAP  If you selected EAP-PEAP, enter the login name of your wireless network in the Login Name field. Enter the name of the server in the Server Name field. Enter the password of your wireless network in the Password field.   Click the Next button to continue, and then go to step 8. Click the Back button to return to the previous screen.   RADIUS  RADIUS features WEP used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) If you selected RADIUS, the EAP setting screen will appear. RADIUS offers two authentication types: EAP-TLS and EAP-PEAP.   Authentication Type - Select the authentication method your network is using, EAP-TLS or EAP-PEAP. These options are described below.   EAP-TLS  If you selected EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the name of the server in the Server Name field. From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network.   Click the Next button to continue, and then go to step 8. Click the Back button to return to the previous screen.   EAP-PEAP  If you selected EAP-PEAP, enter the login name of your wireless network in the Login Name field. Enter the name of the server in the Server Name field. Enter the password of your wireless network in the Password field.   Click the Next button to continue, and then go to step 8. Click the Back button to return to the previous screen.
LEAP  If you selected LEAP, then the LEAP setting screen will appear.   Login Name - Enter the Login name of your wireless network in the Login Name field.  Password - Enter the password of your wireless network in the Password field.  Click the Next button to continue, and then go to step 8. Click the Back button to return to the previous screen.   8. The Confirm New Settings screen will appear next, showing the new settings. To save the new settings, click the Yes button. To edit the new settings, click the Back button. To cancel these new settings, click the Cancel button.  9. The Congratulations screen will appear next. Click Activate new settings now to implement the new settings immediately and return to the Link Information screen. Click Activate new settings later to keep the current settings active and return to the Profiles screen.  You have successfully created a connection profile.   Click the X (Close) button in the upper right corner to exit the WLAN Monitor.  Appendix A: Troubleshooting   This appendix consists of two parts: “Common Problems and Solutions” and “Frequently Asked Questions.” This appendix provides solutions to problems that may occur during the installation and operation of the Dual-Band Wireless A+G PCI Adapter. Read the description below to solve your problems. If you can't find an answer here, check the Linksys website at www.linksys.com.  Common Problems and Solutions   1. The Dual-Band Wireless A+G PCI Adapter does not work properly.   • Power off your PC.   • Reinsert the Adapter into the PC’s PCI slot.   • For Windows 98 or Me, right-click My Computer, and select Properties. Select the Device Manager tab, and select the Adapter. You will find the Adapter if it has been installed successfully. If you see a yellow exclamation mark, the resources may be in conflict, and you must follow the steps below:   • Uninstall the driver software from your PC.   • Restart your PC and repeat the hardware and software installation as specified in this User Guide.  2. I cannot communicate with a wired computer linked via an access point in the infrastructure configuration.   • Make sure that the PC is powered on.   • Make sure that the Dual-Band Wireless A+G PCI Adapter is configured with the same SSID and WEP encryption as the other computers in your wireless network.   Frequently Asked Questions   Can I run an application from a remote computer over the wireless network?   This will depend on whether or not the application is designed to be used over a network. Consult the application’s user guide to determine if it supports operation over a network.   Can I play computer games with other members of the wireless network?   Yes, as long as the game supports multiple players over a LAN (local area network). Refer to the game’s user guide for more information.   What is the IEEE 802.11a standard?   It is one of the IEEE standards for wireless networks. The 802.11a standard allows wireless networking hardware from different manufacturers to communicate, provided that the hardware complies with the 802.11a standard.   The 802.11a standard states a maximum data transfer rate of 54Mbps and an operating frequency of 5GHz.   What is the IEEE 802.11b standard?   It is one of the IEEE standards for wireless networks. The 802.11b standard allows wireless networking hardware   from different manufacturers to communicate, provided that the hardware complies with the 802.11b standard.
The 802.11b standard states a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz.   What is the IEEE 802.11g standard?   It is one of the IEEE standards for wireless networks. The 802.11g standard allows wireless networking hardware from different manufacturers to communicate, provided that the hardware complies with the 802.11g standard.   The 802.11g standard states a maximum data transfer rate of 54Mbps and an operating frequency of 2.4GHz.   What IEEE 802.11a features are supported?   The product supports the following IEEE 802.11a functions:   • OFDM protocol   • Multi-Channel Roaming   • Automatic Rate Selection   • RTS/CTS feature   • Fragmentation   What IEEE 802.11b features are supported?   The product supports the following IEEE 802.11b functions:   • CSMA/CA plus Acknowledge protocol   • Multi-Channel Roaming   • Automatic Rate Selection   • RTS/CTS feature   • Fragmentation   • Power Management   What IEEE 802.11g features are supported?   The product supports the following IEEE 802.11g functions:   • CSMA/CA plus Acknowledge protocol   • OFDM protocol   • Multi-Channel Roaming   • Automatic Rate Selection   • RTS/CTS feature   • Fragmentation   • Power Management   What is ad-hoc mode?   When a wireless network is set to ad-hoc mode, the wireless-equipped computers are configured to communicate directly with each other. The ad-hoc wireless network will not communicate with any wired network.   What is infrastructure mode?   When a wireless network is set to infrastructure mode, the wireless network is configured to communicate with a wired network through a wireless access point.   What is ISM band?   The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the ISM (Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available worldwide. This presents a truly revolutionary opportunity to place convenient high-speed wireless capabilities in the hands of users around the globe.   What is Spread Spectrum?   Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade-off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives,   Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS).   What is DSSS? What is FHSS? And what are their differences?   Frequency-Hopping Spread-Spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that is known to both transmitter and receiver. Properly synchronized, the net effect is
to maintain a single logical channel. To an unintended receiver, FHSS appears to be short-duration impulse noise. Direct-Sequence Spread- Spectrum (DSSS) generates a redundant bit pattern for each bit to be transmitted. This bit pattern is called a chip (or chipping code). The longer the chip, the greater the probability that the original data can be recovered. Even if one or more bits in the chip are damaged during transmission, statistical techniques embedded in the radio can recover the original data without the need for retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected (ignored) by most narrowband receivers.  Would the information be intercepted while transmitting on air?   WLAN features two-fold protection in security. On the hardware side, as with Direct Sequence Spread Spectrum technology, it has the inherent security feature of scrambling. On the software side, WLAN offers the encryption function (WEP) to enhance security and access control.   What is WEP?   WEP is Wired Equivalent Privacy, a data privacy mechanism based on a shared key algorithm, as described in the   IEEE 802.11 standard.   Appendix B: Wireless Security   Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of Linksys products provide several network security features, but they require specific action on your part for implementation. So, keep the following in mind whenever you are setting up or using your wireless network.   Security Precautions   The following is a complete list of security precautions to take (at least steps 1 through 5 should be followed):   1. Change the default SSID.   2. Disable SSID Broadcast.   3. Change the default password for the Administrator account.   4. Enable MAC Address Filtering.   5. Change the SSID periodically.   6. Use the highest encryption algorithm possible. Use WPA if it is available. Please note that this may reduce your network performance.   7. Change the WEP encryption keys periodically.   Security Threats Facing Wireless Networks   Wireless networks are easy to find. Hackers know that in order to join a wireless network, wireless networking products first listen for “beacon messages”. These messages can be easily decrypted and contain much of the network’s information, such as the network’s SSID (Service Set Identifier). Here are the steps you can take:   Change the administrator’s password regularly. With every wireless networking device you use, keep in mind that network settings (SSID, WEP keys, etc.) are stored in its firmware. Your network administrator is the only person who can change network settings. If a hacker gets a hold of the administrator’s password, he, too, can change those settings. So, make it harder for a hacker to get that information. Change the administrator’s password regularly.   SSID. There are several things to keep in mind about the SSID:  1. Disable Broadcast   2. Make it unique   3. Change it often   Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be more convenient, it allows anyone to log into your wireless network. This includes hackers. So, don’t broadcast the SSID.   Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is “linksys”.)   Hackers know these defaults and can check these against your network. Change your SSID to something unique and not something related to your company or the networking products you
use.  Change your SSID regularly so that any hackers who have gained access to your wireless network will have to start from the beginning in trying to break in.   MAC Addresses. Enable MAC Address filtering. MAC Address filtering will allow you to provide access to only those wireless nodes with certain MAC Addresses. This makes it harder for a hacker to access your network with a random MAC Address.   WEP Encryption. Wired Equivalent Privacy (WEP) is often looked upon as a cure-all for wireless security concerns. This is overstating WEP’s ability. Again, this can only provide enough security to make a hacker’s job   more difficult.   There are several ways that WEP can be maximized:   1. Use the highest level of encryption possible   2. Use “Shared Key” authentication   3. Change your WEP key regularly   WPA. Wi-Fi Protected Access (WPA) is the newest and best available standard in Wi-Fi security. Two modes are available: WPA-PSK and WPA-RADIUS. WPA-PSK gives you a choice of two encryption methods: TKIP (Temporal   Key Integrity Protocol), which utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers, and AES (Advanced Encryption Standard), which utilizes a symmetric 128-Bit block data encryption. WPA-RADIUS offers two encryption methods, TKIP and AES, with dynamic encryption keys, and it uses a RADIUS (Remote Authentication Dial-In User Service) server for authentication.   WPA-PSK. If you do not have a RADIUS server, select the type of algorithm you want to use, TKIP or AES, and enter a password in the Passphrase field of 8-63 characters.   WPA-RADIUS. WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router or other device.) WPA-RADIUS offers two encryption methods, TKIP and AES, with dynamic encryption keys.   Implementing encryption may have a negative impact on your network’s performance, but if you are transmitting sensitive data over your network, encryption should be used.   These security recommendations should help keep your mind at ease while you are enjoying the most flexible and convenient technology Linksys has to offer.   Appendix C: Windows Help   Most Linksys wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix.   TCP/IP  Before a computer can communicate with an access point or wireless router, TCP/IP must be enabled. TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a network. This is true for wireless networks as well. Your PCs will not be able to utilize wireless networking without having TCP/IP enabled. Windows Help provides complete instructions on enabling TCP/IP.   Shared Resources   If you wish to share printers, folder, or files over your network, Windows Help provides complete instructions on utilizing shared resources.   Network Neighborhood/My Network Places   Other PCs on your network will appear under Network Neighborhood or My Network Places (depending upon the version of Windows you're running). Windows Help provides complete instructions on adding PCs to your network.   Appendix D: Glossary   802.11a - An IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps and an operating frequency of 5GHz.
802.11b - An IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz.   802.11g - An IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices.   Access Point - Device that allows wireless-equipped computers and other devices to communicate with a wired   network. Also used to expand the range of a wireless network.   AES (Advanced Encryption Standard) - A 256-bit encryption technique used to secure data.   Adapter - This is a device that adds network functionality to your PC.   Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer) without the use of an access point.   Backbone - The part of a network that connects most of the systems and networks together, and handles the most data.   Bandwidth - The transmission capacity of a given device or network.   Beacon Interval - The frequency interval of the beacon, which is a packet broadcast by a router to synchronize a wireless network.   Bit - A binary digit.   Boot - To start a device and cause it to start executing instructions.   Bridge - A device that connects two different kinds of local networks, such as a wireless network to a wired Ethernet network.   Broadband - An always-on, fast Internet connection.   Browser - A browser is an application program that provides a way to look at and interact with all the information on the World Wide Web.   Buffer - A block of memory that temporarily holds data to be worked on later when a device is currently too busy to accept the data.   Cable Modem - A device that connects a computer to the cable television network, which in turn connects to the Internet.   CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) - A method of data transfer that is used to prevent data loss in a network.   CTS (Clear To Send) - A signal sent by a device to indicate that it is ready to receive data.   Daisy Chain - A method used to connect devices in a series, one after the other.   Database - A collection of data that is organized so that its contents can easily be accessed, managed, and updated.   DDNS (Dynamic Domain Name System) - The capability of having a website, FTP, or e-mail server-with a dynamic IP address-use a fixed domain name.   Default Gateway - A device that forwards Internet traffic from your local area network.   DHCP (Dynamic Host Configuration Protocol) - A protocol that lets one device on a local network, known as a DHCP server, assign temporary IP addresses to the other network devices, typically computers.  DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be “seen” from the Internet.   DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP addresses.   Domain - A specific name for a network of computers.   Download - To receive a file transmitted over a network.   DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines.   DSSS (Direct-Sequence Spread-Spectrum) - A type of radio transmission technology that includes a redundant bit pattern to lessen the probability of data lost during transmission. Used in 802.11b networking.   DTIM (Delivery Traffic Indication Message) - A message included in data packets that can increase wireless efficiency.   Dynamic IP Address - A temporary IP address assigned by a DHCP server.   EAP (Extensible Authentication Protocol) - A general authentication protocol used to control network access.   Many specific authentication methods work within this framework.   EAP-PEAP (Extensible Authentication Protocol-Protected Extensible Authentication Protocol) - A
mutual authentication method that uses a combination of digital certificates and another system, such as passwords.   EAP-TLS (Extensible Authentication Protocol-Transport Layer Security) - A mutual authentication method that uses digital certificates.   Encryption - Encoding data to prevent it from being read by unauthorized people.   Ethernet - An IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium.   Finger - A program that tells you the name associated with an e-mail address.   Firewall - Security measures that protect the resources of a local network from intruders.   Firmware - 1. In network devices, the programming that runs the device. 2. Programming loaded into read-only memory (ROM) or programmable read-only memory (PROM) that cannot be altered by end-users.   Fragmentation - Breaking a packet into smaller units when transmitting over a network medium that cannot support the original size of the packet.   FTP (File Transfer Protocol) - A standard protocol for sending files between computers over a TCP/IP network and the Internet.   Full Duplex - The ability of a networking device to receive and transmit data simultaneously.   Gateway - A system that interconnects networks.   Half Duplex - Data transmission that can occur in two directions over a single line, but only one direction at a time.   Hardware - The physical aspect of computers, telecommunications, and other information technology devices.   HTTP (HyperText Transport Protocol) - The communications protocol used to connect to servers on the World Wide Web.   IEEE (The Institute of Electrical and Electronics Engineers) - An independent institute that develops networking standards.   Infrastructure - Currently installed computing and networking equipment.   Infrastructure Mode - Configuration in which a wireless network is bridged to a wired network via an access point.   IP (Internet Protocol) - A protocol used to send data over a network.   IP Address - The address used to identify a computer or device on a network.   IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device.   IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer.   ISM band - Radio band used in wireless networking transmissions.   ISP (Internet Service Provider) - A company that provides access to the Internet.   LAN (Local Area Network) - The computers and networking products that make up the network in your home or office.   LEAP (Lightweight Extensible Authentication Protocol) - A mutual authentication method that uses a username and password system.   MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking device.   Mbps (Megabits Per Second) - One million bits per second; a unit of measurement for data transmission.  Multicasting - Sending data to a group of destinations at once.   NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different IP address for the Internet.   Network - A series of computers or devices connected for the purpose of data sharing, storage, and/or transmission between users.   NNTP (Network News Transfer Protocol) - The protocol used to connect to Usenet groups on the Internet.  Node - A network junction or connection point, typically a computer or work station.   OFDM (Orthogonal Frequency Division Multiplexing) - A type of modulation technology that separates the data stream into a number of lower-speed data streams, which are then transmitted in parallel. Used in 802.11a,
802.11g, and powerline networking.   Packet - A unit of data sent over a network.   Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically generating the WEP encryption keys for Linksys products.   Ping (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online.   POP3 (Post Office Protocol 3) - A standard protocol used to retrieve e-mail stored on a mail server.  Port - 1. The connection point on a computer or networking device used for plugging in a cable or an adapter. 2.   The virtual connection point through which a computer uses a specific application on a server.   Power over Ethernet (PoE) - A technology enabling an Ethernet network cable to deliver both data and power.   PPPoE (Point to Point Protocol over Ethernet) - A type of broadband connection that provides authentication (username and password) in addition to data transport.   PPTP (Point-to-Point Tunneling Protocol) - A VPN protocol that allows the Point to Point Protocol (PPP) to be tunneled through an IP network. This protocol is also used as a type of broadband connection in Europe.   Preamble - Part of the wireless signal that synchronizes network traffic.   RADIUS (Remote Authentication Dial-In User Service) - A protocol that uses an authentication server to control network access.   RJ-45 (Registered Jack-45) - An Ethernet connector that holds up to eight wires.   Roaming - The ability to take a wireless device from one access point's range to another without losing the connection.   Router - A networking device that connects multiple networks together, such as a local network and the Internet.   RTS (Request To Send) - A packet sent when a computer has data to transmit. The computer will wait for a CTS (Clear To Send) message before sending data.   Server - Any computer whose function in a network is to provide user access to files, printing, communications, and other services.   SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet.   SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol.  Software - Instructions for the computer. A series of instructions that performs a particular task is called a “program”.   Spread Spectrum - Wideband radio frequency technique used for more reliable and secure data transmission.  SSID (Service Set IDentifier) - Your wireless network's name.   Static IP Address - A fixed address assigned to a computer or device that is connected to a network.  Static Routing - Forwarding data in a network via a fixed path.   Subnet Mask - An address code that determines the size of the network.   Switch - 1. Device that is the central point of connection for computers and other devices in a network, so data can be shared at full transmission speeds. 2. A device for making, breaking, or changing the connections in an electrical circuit.   TCP/IP (Transmission Control Protocol/Internet Protocol) - A network protocol for transmitting data that requires acknowledgement from the recipient of data sent.   Telnet - A user command and TCP/IP protocol used for accessing remote PCs.   TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol that uses UDP and has no directory or password capability.   Throughput - The amount of data moved successfully from one node to another in a given time period.  TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted.   Topology - The physical layout of a network.   TX Rate - Transmission Rate.
UDP (User Datagram Protocol) - A network protocol for transmitting data that does not require acknowledgement from the recipient of the data that is sent.   Upgrade - To replace existing software or firmware with a newer version.   Upload - To transmit a file over a network.   URL (Uniform Resource Locator) - The address of a file located on the Internet.   VPN (Virtual Private Network) - A security measure to protect data as it leaves one network and goes to another over the Internet.   WAN (Wide Area Network) - The Internet.   WEP (Wired Equivalent Privacy) - A method of encrypting data transmitted on a wireless network for greater security.   WINIPCFG - A Windows 98 and Millennium utility that displays the IP address for a particular networking device.   WLAN (Wireless Local Area Network) - A group of computers and associated devices that communicate with each other wirelessly.   WPA (Wi-Fi Protected Access) - A wireless security protocol using TKIP (Temporal Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server.   Appendix E: Specifications   Standards IEEE 802.11a, 802.11b, 802.11g   Interface PCI   LEDs LINK, PWR   Transmit Power 11 dBm to 18 dBm  Modulation 802.11a and 802.11g: OFDM   802.11b: CCK, DQPSK, DBPSK   Security Feature WEP   WEP Key Bits 64, 128, 152 Bits   Protocols TCP/IP   Dimensions 5.79" x 0.79" x 4.72" (147 mm x 20 mm x 120 mm)   Unit Weight 3.6 oz. (0.1 kg)   Certifications FCC, CE, IC-03   Operating Temp 32° F to 131° F (0° C to 55° C)   Storage Temp -4° F to 185° F (-20° C to 85° C)   Operating Humidity 10% to 85%, Non-Condensing   Storage Humidity 5% to 90%, Non-Condensing   Appendix F: Warranty Information   LIMITED WARRANTY   Linksys warrants to You that, for a period of three years (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates. This limited warranty extends only to the original purchaser.   If the Product proves defective during the Warranty Period call Linksys Technical Support in order to obtain a Return Authorization Number, if applicable. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. If You are requested to return the Product, mark the Return Authorization Number clearly on the outside of the package and include a copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You are responsible for shipping defective Products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You only. Customers located outside of the United States of America and Canada are responsible for all shipping and handling charges.
ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives You specific legal rights, and You may also have other rights which vary by jurisdiction.   This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated, repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new techniques for intruding upon and attacking networks, Linksys does not warrant that the Product will be free of vulnerability to intrusion or attack.   TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT   (INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even   if any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You.   Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.   Appendix G: Regulatory Information  FCC STATEMENT     This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.  However, there is no guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.IMPORTANT NOTE:FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.If this device is going to be operated in 5.15 ~ 5.25GHz frequency range, then it is restricted in indoor environment only.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.INDUSTRY CANADA (CANADA)This Class B digital apparatus complies with Canadian ICES-003.    Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations.  EC DECLARATION OF CONFORMITY (EUROPE)  
Linksys declares that the Dual-Band Wireless A+G PCI Adapter conforms to the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC:   EN 301 489-1, 301 489-17 General EMC requirements for Radio equipment.   EN 609 50 Safety   EN 300-328-1, EN 300-328-2 Technical requirements for Radio equipment.   Caution: This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. Contact local Authority for procedure to follow.   Note: Combinations of power levels and antennas resulting in a radiated power level of above 100 mW equivalent isotropic radiated power (EIRP) are considered as not compliant with the above mentioned directive and are not allowed for use within the European community and countries that have adopted the European R&TTE directive 1999/5/EC.   For more details on legal combinations of power levels and antennas, contact Linksys Corporate Compliance.   Linksys vakuuttaa täten että Dual-Band Wireless A+G PCI Adapter tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien näiden direktiivien muiden ehtojen mukainen.   Linksys Group déclare la Dual-Band Wireless A+G PCI Adapter est conforme aux conditions essentielles et aux dispositions relatives à la directive 1999/5/EC.   Belgique: Dans le cas d'une utilisation privée, à l'extérieur d'un bâtiment, au-dessus d'un espace public, aucun enregistrement n'est nécessaire pour une distance de moins de 300m. Pour une distance supérieure à 300m un enregistrement auprès de l'IBPT est requise. Pour une utilisation publique à l'extérieur de bâtiments, une licence de l'IBPT est requise. Pour les enregistrements et licences, veuillez contacter l'IBPT.   France:  2.4 GHz Bande : les canaux 10, 11, 12, 13 (2457, 2462, 2467, et 2472 MHz respectivement) sont complétement libres d'utilisation en France (en utilisation intérieur). Pour ce qui est des autres canaux, ils peuvent être soumis à autorisation selon le départment. L'utilisation en extérieur est soumis à autorisation préalable et très restreint.   Vous pouvez contacter l'Autorité de Régulation des Télécommunications (http://www.art-telecom.fr) pour de plus amples renseignements.   Appendix H: Contact Information   Need to contact Linksys?   Visit us online for information on the latest products and updates   to your existing products at: http://www.linksys.com or ftp.linksys.com   Can't find information about a product you want to buy on the web? Do you want to know more about networking   with Linksys products? Give our advice line a call at: 800-546-5797 (LINKSYS)   Or fax your request in to: 949-823-3002   If you experience problems with any Linksys product,   you can call us at: 800-326-7114   Don't wish to call? You can e-mail us at: support@linksys.com   If any Linksys product proves defective during its warranty period,   you can call the Linksys Return Merchandise Authorization   department for obtaining a Return Authorization Number at: 949-823-3000   (Details on Warranty and RMA issues can be found in the Warranty   Information section in this Guide.)      Linksys declares that WMP55AG ver. 1.3 ( FCC ID: Q87-WMP55AGV13 ) is limited in CH1~CH11 for 2.4 GHz by specified firmware controlled in U.S.A.

Navigation menu